drill and boring bits, adapters · drill and boring bits, adapters 800-544-8436

Drill and Boring Bits, Adapters

800-544-8436 www.guhdo.com

Hinge Boring Bit T.C. Z2+V230103Dmm

L1mm

Part-No.Shankmm

25 65 30103-5-02500-R830 65 30103-5-03000-R835 65 30103-5-03500-R8

Technical detailsTwo raker teeth, centre point and two inserted spurs. Right-hand rotation.

ApplicationFor drilling of accurate holes for hinges in hardwood and various kinds of wood composites on portable routers. Forhard, brittle synthetic coating we recommend No. 30190.

2.1PU = packing unit

Hinge Boring Bit T.C. Z230190 interchangeable shank designDmm

L1mm

Part-No.Shankmm

35 60 30193-5-35000-R835 60 30196-5-35000-R1235 50 30197-5-35000-RM 1035 50 30198-5-35000-RM 12 x 1

ApplicationFor drilling of accurate holes for hinges on portable routers.

Technical detailsTwo raker teeth, centre point, with ground side bevel. Cutting angle geometry designed for speed up to 25 000R.P.M. Right-hand rotation.

2.2popular size, ex stockwhile stocks last

PU = packing unit

Hinge Boring Bit with interchangeable T.C. tip22650 interchangeable shank designDmm

L1mm

Part-No.Shankmm

34 59 22658-5-34000-RM 12 x 1

Part-No.Spare parts / Accessories PU

Interch. T.C. tip for D= 34 mm 172650-6-34000-RInterch. T.C. tip for D= 35 mm 172650-6-35000-RTorx countersunk screw M 4 x 8, T10 1039084-0-04080-R

Technical details/ApplicationWith 1 straight interchangeable T.C. tip with centre point, chip guiding step and side bevels. For drilling of tear-freeholes and hinge holes on portable routers up to 25 000 R.P.M.


PU = packing unit

Slot Bit T.C.T.30025Dmm

L2mm

L1mm

Shankmm

Part-No.

5 20 IG M 6 x 0,7549 30025-5-05000-R6 20 IG M 6 x 0,7549 30025-5-06000-R8 25 IG M 6 x 0,7549 30025-5-08000-R10 25 IG M 6 x 0,7549 30025-5-10000-R

IG = internal thread

Technical detailsTwo cutting edges with ground side bevel, without centre point. Shank with internal thread and clamping flat. Right-handrotation.

ApplicationFor use on FESTO-DOMINO-joining machines. Oscillating routing of long holes for Domino-dowels.

for FESTO - DOMINO


PU = packing unit

Dowel Drill T.C.T.30515Dmm

L2mm

L1mm

Shankmm

Part-No.

5 30 8 x 1757,5 30515-5-05030-R6 30 8 x 1757,5 30515-5-06030-R8 30 8 x 1757,5 30515-5-08030-R10 30 8 x 1858 30515-5-10030-R12 30 8 x 1858 30515-5-12030-R16* 30 8 x 1858/65 30515-5-16030-R

* Only on DD40P

ApplicationFor drilling of blind-holes in solid wood, various wood composites and boards etc. on MAFELL-Duo dowel machinesDD40G and DD40P, as well as on portable routers.

Technical detailsCentre point and two cutting edges with side bevel. Cutting geometry designed for high spindle speeds. Spiral partTeflon-coated. Parallel shank with clamping flat and length adjusting screw. Right-hand rotation.

for Mafell


PU = packing unit

Diamond (PCD) Dowel Drills30540-9 for blind holes Z2Dmm

L2mm

L4mm

Part-No.L1mm

Shankmm

8 27 57,52,6 30540-9-08025-L10 x 268 27 57,52,6 30540-9-08025-R10 x 268 35 702,6 30540-9-08035-L10 x 308 35 702,6 30540-9-08035-R10 x 3010 35 703,2 30540-9-10035-L10 x 3010 35 703,2 30540-9-10035-R10 x 30

30565-9 for through holes Z1Dmm

L2mm

L4mm

Part-No.L1mm

Shankmm

Z

5 27 57,54,5 30565-9-05027-L10 x 26 15 27 57,54,5 30565-9-05027-R10 x 26 15 35 704,5 30565-9-05035-L10 x 26 15 35 704,5 30565-9-05035-R10 x 26 18 35 706,5 30565-9-08035-L10 x 26 18 35 706,5 30565-9-08035-R10 x 26 1

30566-9 for through holes Z2Dmm

L2mm

L4mm

Part-No.L1mm

Shankmm

8 35 706,4 30566-9-08035-L10 x 268 35 706,4 30566-9-08035-R10 x 2610 35 708,6 30566-9-10035-R10 x 2612 35 709,5 30566-9-12035-L10 x 2612 35 709,5 30566-9-12035-R10 x 26

Technical detailsNo. 30540-9: Two PCD cutting edges with double bevel.No. 30565-9: Z1 with V-point and with double bevel.No. 30566-9: Z2 with V-point and with double bevel. Shank with clamping flat and adjusting screw.

ApplicationFor drilling of accurate blind-holes or through-holes in extremely abrasive materials, e.g. MDF, HDF etc., fire resistantchipboard and MDF-board or gypsum plaster boards. For use on automatic dowel hole machines or CNC machines. No. 30540-9/30566-9 in D < 8 mm and No. 30565-9: Not applicable for particularly dense workpiece material (e.g.Corian, Trespa, etc.)


PU = packing unit

Twist Drill for load-bearing bolts T.C.30145-5/30150-5Dmm

L2mm

L1mm

Shankmm

Part-No.

12 65 10 x 30*105 30145-5-12065-R12 105 13 x 50170 30150-5-12000-R13 110 13 x 50175 30150-5-13000-R

Technical detailsSolid T.C. head with two cutting edges, centre point and negatively ground spurs. Spiral portion Teflon-coated. Withlanded flute. Right-hand rotation.

ApplicationFor drilling accurate blind-holes for hinges with load-bearing bolts.

* With clamping flat For other diameters see pages 2.15/2.38.


PU = packing unit

Solid T.C. Twist Drill30566-6Dmm

L2mm

L1mm

Shankmm

Part-No.

3 27 10 x 2457,5 30566-6-03027-R3 27 10 x 3370 30566-6-03070-R

Technical details/ApplicationSpiral portion in solid T.C. with V-point 120°. Parallel shank with clamping flat and length adjusting screw. Right-handrotation. For drilling fastening holes for face plates, striking plates, and mounting plates for floor sealings on CNCmachines.

for fastening holes


PU = packing unit

Twist Drill - solid T.C.30120 common shank and drilling diameterDmm

L2mm

Part-No.L1mm

2 12 30120-6-02000-L382 12 30120-6-02000-R282,5 14 30120-6-02500-L432,5 14 30120-6-02500-R433 16 30120-6-03000-L463 16 30120-6-03000-R463 27 30120-6-03027-L463 27 30120-6-03027-R463,5 20 30120-6-03500-L523,5 20 30120-6-03500-R523,5 30 30120-6-03530-L523,5 30 30120-6-03530-R524 22 30120-6-04000-L584 22 30120-6-04000-R584 32 30120-6-04032-L584 32 30120-6-04032-R585 26 30120-6-05000-L585 26 30120-6-05000-R585 35 30120-6-05035-L585 35 30120-6-05035-R58

Technical details/ApplicationV-point, common shank and drilling diameter. For use in adaptor bushes Nos. 39220/39225.


PU = packing unit

Boring Pin - Solid T.C.20005Dmm

L2mm

L1mm

Shankmm

Part-No.

Common shank and drilling diameter 1)

2,0 12 2,038 20005-6-02000-02,5 15 2,545 20005-6-02500-03,0 15 3,045 20005-6-03000-03,0 23 3,048 20005-6-03023-03,5 15 3,545 20005-6-03500-03,5 30 3,555 20005-6-03530-04,0 20 4,045 20005-6-04000-04,0 32 4,057,5 20005-6-04032-0

Shank 10 mm, L1 = 57,5 mm

2,5 15 10 x 3357,5 20005-6-02515-03,0 15 10 x 3357,5 20005-6-03015-03,5 15 10 x 3357,5 20005-6-03515-04,0 20 10 x 3357,5 20005-6-04020-05,0 25 10 x 2557,5 20005-6-05025-06,0 25 10 x 2557,5 20005-6-06025-08,0 25 10 x 2657,5 20005-6-08025-0

Shank 10 mm, L1 = 70 mm

2,5 15 10 x 3370 20005-6-02570-03,0 23 10 x 3370 20005-6-03070-03,5 30 10 x 3370 20005-6-03570-04,0 32 10 x 2570 20005-6-04070-05,0 35 10 x 2570 20005-6-05035-06,0 35 10 x 2570 20005-6-06035-08,0 35 10 x 2570 20005-6-08035-0

• Extremely long tool life which could only be achieved with diamond drills!

• Applicable for R.-H. and L.-H. rotation!

• Large regrinding area, modest regrinding costs!

1) * To be used with adaptors No. 39225 ( see page 2.51).


Length adjusting screw Length adjusting screw 1039075-0-05080-RLength adjusting screw M 5 x 17, special design* 1039075-0-05017-R

DBP

Technical detailsRound tool body with special grade solid T.C. with oneparallel flute and tapered point. D = 2,5 to 4 mm withcommon shank and clamping diameter, to be used inconjunction with adaptor No. 39225 or with brazedshank 10 mm, with clamping flat and length adjustingscrew. From D = 5 mm upwards brazed into shank 10mm. Can be used for either right-hand or left-handrotation.

ApplicationBesonders geeignet für Sacklöcher in abrasivwirkenden Werkstoffen, auch mit mineralischenBestandteilen. Auch für trockene Massivhölzereinsetzbar. Einsatz auf Dübellochbohrautomaten oderCNC-Maschinen. Die Anzahl der Bohrstifte, diezusammen in einem Bohrgetriebe eingesetzt werdenkönnen, hängt von der Leistungsfähigkeit derMaschine ab.


PU = packing unit

Dowel Drill - Solid T.C.30550-6 parallel shank 10 mmDmm

L2mm

Part-No.Shankmm

Overall length 57,5 mm

2,5 14 30550-6-02514-L10 x 332,5 14 30550-6-02514-R10 x 333 16 30550-6-03016-L10 x 333 16 30550-6-03016-R10 x 333,5 20 30550-6-03520-L10 x 333,5 20 30550-6-03520-R10 x 334 22 30550-6-04022-L10 x 254 22 30550-6-04022-R10 x 255 27 30550-6-05027-L10 x 255 27 30550-6-05027-R10 x 256 27 30550-6-06027-L10 x 256 27 30550-6-06027-R10 x 25

Overall length 70 mm

3 27 30550-6-03027-L10 x 333 27 30550-6-03027-R10 x 333,5 30 30550-6-03530-L10 x 333,5 30 30550-6-03530-R10 x 334 32 30550-6-04032-L10 x 254 32 30550-6-04032-R10 x 255 35 30550-6-05035-L10 x 255 35 30550-6-05035-R10 x 256 35 30550-6-06035-L10 x 256 35 30550-6-06035-R10 x 25


Length adjusting screw 1039075-0-05080-RLength adjusting screw M 5 x 17, special design* 1039075-0-05017-R

with flat point

Technical detailsSolid T.C. spiral protion with flat centre point, shapedby the point angle and two negative ground,strengthened spurs. Enlarged flutes. Parallel shankwith clamping flat and length adjusting screw.

ApplicationFor use in adaptor chucks etc. on dowel hole boringmachines and CNC machines. To drill blind-holes insolid wood, various kinds of wood composites andboards etc., as well as in plastic laminated materials.

• Essential improvement of the tool life achieved through more wear resistant T.C. grade

• Little vibration stress through rigid solid T.C. design

• No break-outs when retracting the drill through non-stepped parallel spiral portion

• Maximum concentricity

• Regrinding area considerably increased


PU = packing unit

ISODUR Dowel Drills T.C.T.30555 parallel shank 10 mmDmm

L2mm

Part-No.Shankmm


5 27 30555-5-05027-L10 x 275 27 30555-5-05027-R10 x 276 27 30555-5-06027-L10 x 276 27 30555-5-06027-R10 x 278 27 30555-5-08027-L10 x 278 27 30555-5-08027-R10 x 2710 27 30555-5-10027-L10 x 2710 27 30555-5-10027-R10 x 27


5 35 30555-5-05035-L10 x 305 35 30555-5-05035-R10 x 306 35 30555-5-06035-L10 x 306 35 30555-5-06035-R10 x 307 35 30555-5-07035-L10 x 307 35 30555-5-07035-R10 x 308 35 30555-5-08035-L10 x 308 35 30555-5-08035-R10 x 3010 35 30555-5-10035-L10 x 3010 35 30555-5-10035-R10 x 3012 35 30555-5-12035-L10 x 3012 35 30555-5-12035-R10 x 30


5 42 30555-5-05044-L10 x 305 42 30555-5-05044-R10 x 308 42 30555-5-08044-L10 x 308 42 30555-5-08044-R10 x 30



with flat point

Technical detailsSolid T.C. head with flat centre point shaped by thepoint angle and two negatively ground spurs. Enlargedflutes. Spiral portion Teflon-coated for reduced frictionand better chip flow. Parallel shank with clamping flatand length adjusting screw. Tool life furtherincreased compared with No. 30550, by optimizingthe T.C. grade, the grinding quality, as well as thegeometry of the cutting edges.

ApplicationFor use in adaptor chucks, etc. on dowel hole boringmachines and CNC machines to drill blind-holes insolid wood, various kinds of wood composites andboards etc. also in plastic laminated materials.

• Considerably increased tool life compared with traditional T.C. dowel drills

• Set-up times can be enormously reduced for only a small extra costs


PU = packing unit

Dowel Drill T.C.T.30540-5 parallel shank 10 mmDmm

L2mm

Shankmm

Part-No.


4 27 10 x 27 30540-5-04027-L4 27 10 x 27 30540-5-04027-R4,5 27 10 x 27 30540-5-04527-L4,5 27 10 x 27 30540-5-04527-R5 27 10 x 27 30540-5-05027-L5 27 10 x 27 30540-5-05027-R5,1 27 10 x 27 30540-5-05127-L5,1 27 10 x 27 30540-5-05127-R5,2 27 10 x 27 30540-5-05227-R6 27 10 x 27 30540-5-06027-L6 27 10 x 27 30540-5-06027-R6,35 27 10 x 27 30540-5-06327-L6,35 27 10 x 27 30540-5-06327-R8 27 10 x 27 30540-5-08027-L8 27 10 x 27 30540-5-08027-R8,2 27 10 x 27 30540-5-08227-L8,2 27 10 x 27 30540-5-08227-R9 27 10 x 27 30540-5-09027-R10 27 10 x 27 30540-5-10027-L10 27 10 x 27 30540-5-10027-R10,5 27 10 x 27 30540-5-10527-L10,5 27 10 x 27 30540-5-10527-R11 27 10 x 27 30540-5-11027-L11 27 10 x 27 30540-5-11027-R12 27 10 x 27 30540-5-12027-R12,7 27 10 x 27 30540-5-12727-L12,7 27 10 x 27 30540-5-12727-R


4 35 10 x 30 30540-5-04035-L4 35 10 x 25 30540-5-04035-R4,5 35 10 x 30 30540-5-04535-L4,5 35 10 x 30 30540-5-04535-R5 35 10 x 30 30540-5-05035-L5 35 10 x 30 30540-5-05035-R5,1 35 10 x 30 30540-5-05135-L5,1 35 10 x 30 30540-5-05135-R5,2 35 10 x 30 30540-5-05235-R5,5 35 10 x 30 30540-5-05535-L5,5 35 10 x 30 30540-5-05535-R6 35 10 x 30 30540-5-06035-L6 35 10 x 30 30540-5-06035-R6,2 35 10 x 30 30540-5-06235-R6,35 35 10 x 30 30540-5-06335-L6,35 35 10 x 30 30540-5-06335-R6,5 35 10 x 30 30540-5-06535-L6,5 35 10 x 30 30540-5-06535-R7 35 10 x 30 30540-5-07035-L7 35 10 x 30 30540-5-07035-R7,5 35 10 x 30 30540-5-07535-L7,5 35 10 x 30 30540-5-07535-R8 35 10 x 30 30540-5-08035-L8 35 10 x 30 30540-5-08035-R8,1 35 10 x 30 30540-5-08135-L8,1 35 10 x 30 30540-5-08135-R8,2 35 10 x 30 30540-5-08235-L8,2 35 10 x 30 30540-5-08235-R8,5 35 10 x 30 30540-5-08535-L8,5 35 10 x 30 30540-5-08535-R9 35 10 x 30 30540-5-09035-L9 35 10 x 30 30540-5-09035-R9,52 35 10 x 30 30540-5-09535-L9,52 35 10 x 30 30540-5-09535-R10 35 10 x 30 30540-5-10035-L10 35 10 x 30 30540-5-10035-R10,2 35 10 x 30 30540-5-10235-L

without landed flute


PU = packing unit

10,2 35 10 x 30 30540-5-10235-R10,5 35 10 x 30 30540-5-10535-R11 35 10 x 30 30540-5-11035-L11 35 10 x 30 30540-5-11035-R12 35 10 x 30 30540-5-12035-L12 35 10 x 30 30540-5-12035-R12,7 35 10 x 30 30540-5-12735-L12,7 35 10 x 30 30540-5-12735-R


5 42 10 x 30 30540-5-05044-L5 42 10 x 30 30540-5-05044-R6 42 10 x 30 30540-5-06044-L6 42 10 x 30 30540-5-06044-R8 42 10 x 30 30540-5-08044-L8 42 10 x 30 30540-5-08044-R10 42 10 x 30 30540-5-10044-L10 42 10 x 30 30540-5-10044-R12 42 10 x 30 30540-5-12044-L12 42 10 x 30 30540-5-12044-R

Technical detailsSolid T.C. head with centre point, two cutting edges and negatively ground spurs. Increased back relief angle. Spiralportion Teflon-coated for reduced friction and better chip flow. Parallel shank with clamping flat and length adjustingscrew.

ApplicationFor use in adaptor chucks, etc. on dowel hole boring machines and CNC machines to drill blind-holes in solid wood,various kinds of wood composites and boards etc., as well as in plastic laminated materials.




PU = packing unit

Dowel Drills T.C.T.30530-5 parallel shank 10 mmDmm

L2mm

Shankmm

Part-No.


5 30 10 x 20 30530-5-05030-L5 30 10 x 20 30530-5-05030-R6 30 10 x 20 30530-5-06030-L6 30 10 x 20 30530-5-06030-R7 30 10 x 20 30530-5-07030-L7 30 10 x 20 30530-5-07030-R8 30 10 x 20 30530-5-08030-L8 30 10 x 20 30530-5-08030-R10 30 10 x 20 30530-5-10030-L10 30 10 x 20 30530-5-10030-R12 30 10 x 20 30530-5-12030-L12 30 10 x 20 30530-5-12030-R13 30 10 x 20 30530-5-13030-R


5 43 10 x 20 30530-5-05043-L5 43 10 x 20 30530-5-05043-R5,5 43 10 x 20 30530-5-05543-L5,5 43 10 x 20 30530-5-05543-R6 43 10 x 20 30530-5-06043-L6 43 10 x 20 30530-5-06043-R7,5 43 10 x 20 30530-5-07543-R8 43 10 x 20 30530-5-08043-L8 43 10 x 20 30530-5-08043-R8,2 43 10 x 20 30530-5-08243-R9 43 10 x 20 30530-5-09043-L9 43 10 x 20 30530-5-09043-R10 43 10 x 20 30530-5-10043-L10 43 10 x 20 30530-5-10043-R12 43 10 x 20 30530-5-12043-L12 43 10 x 20 30530-5-12043-R12,2 43 10 x 20 30530-5-12243-R13 43 10 x 20 30530-5-13043-L13 43 10 x 20 30530-5-13043-R14 43 10 x 20 30530-5-14043-L14 43 10 x 20 30530-5-14043-R15 43 10 x 20 30530-5-15043-L15 43 10 x 20 30530-5-15043-R16 43 10 x 20 30530-5-16043-L16 43 10 x 20 30530-5-16043-R

Technical detailsSolid T.C. head with centre point, two cutting edges and negatively ground spurs. Increased back relief angle. Spiralportion Teflon-coated, with landed flute. Parallel shank with clamping flat and length adjusting screw. No. 30145 withoutlength adjusting screw. The landed flute (heel) provides improved centering on return stroke and permitsinfinitely variable mounting of the countersink directly on the spiral portion of the drill.

ApplicationFor use in adaptor chucks, etc. on dowel hole boring machines and CNC machines to drill blind-holes in solid wood,various kinds of wood composites and boards etc., as well as in plastic laminated materials.



30145-5 parallel shank 10 mmDmm

L2mm

Part-No.Shankmm


5 45 30145-5-05045-L10 x 305 45 30145-5-05045-R10 x 306 45 30145-5-06045-L10 x 306 45 30145-5-06045-R10 x 307 45 30145-5-07045-L10 x 307 45 30145-5-07045-R10 x 308 45 30145-5-08045-L10 x 308 45 30145-5-08045-R10 x 30

with landed flute


PU = packing unit

10 45 30145-5-10045-L10 x 3010 45 30145-5-10045-R10 x 3012 45 30145-5-12045-L10 x 3012 45 30145-5-12045-R10 x 30


5 65 30145-5-05065-L10 x 305 65 30145-5-05065-R10 x 306 65 30145-5-06065-L10 x 306 65 30145-5-06065-R10 x 306,5 65 30145-5-06565-R10 x 307 65 30145-5-07065-L10 x 307 65 30145-5-07065-R10 x 307,5 65 30145-5-07565-R10 x 308 65 30145-5-08065-L10 x 308 65 30145-5-08065-R10 x 308,5 65 30145-5-08565-R10 x 309 65 30145-5-09065-R10 x 3010 65 30145-5-10065-L10 x 3010 65 30145-5-10065-R10 x 3011 65 30145-5-11065-R10 x 3012 65 30145-5-12065-L10 x 3012 65 30145-5-12065-R10 x 30*14 65 30145-5-14065-L10 x 3014 65 30145-5-14065-R10 x 30

Overall length 110/130 ** mm

16 80 30145-5-16080-L10 x 2516 80 30145-5-16080-R10 x 2514 ** 98 30145-5-14098-L10 x 2514 ** 98 30145-5-14098-R10 x 2516 ** 98 30145-5-16098-R10 x 25


PU = packing unit

Dowel Drills HSS30530-4 parallel shank 10 mmDmm

L2mm

Part-No.


5 43 30530-4-05043-L5 43 30530-4-05043-R6 43 30530-4-06043-L6 43 30530-4-06043-R8 43 30530-4-08043-L8 43 30530-4-08043-R

Technical detailsTwo cutting edges with spurs and centre point. Parallel shank, without length adjusting screw.No. 30530: Spiral portion with landed flute.No. 30145: Spiral portion without (with *) landed flute.

ApplicationFor use in adaptor chucks, etc. on dowel hole boring machines or CNC machines. For drilling accurate blind-holes insoft and hardwood.

30145-4 parallel shank 10 mmDmm

L2mm

Part-No.Shankmm


5 45 30145-4-05045-R10 x 308 45 30145-4-08045-L10 x 308 45 30145-4-08045-R10 x 30


PU = packing unit

Dowel Drill T.C.T.30510 parallel shank 8 mmDmm

L2mm

Shankmm

Part-No.


4 30 8 x 20 30510-5-04030-L4 30 8 x 20 30510-5-04030-R5 30 8 x 20 30510-5-05030-L5 30 8 x 20 30510-5-05030-R6 30 8 x 20 30510-5-06030-L6 30 8 x 20 30510-5-06030-R8 30 8 x 20 30510-5-08030-L8 30 8 x 20 30510-5-08030-R10 30 8 x 20 30510-5-10030-L10 30 8 x 20 30510-5-10030-R12 30 8 x 20 30510-5-12030-R


4 40 8 x 20 30510-5-04040-R5 40 8 x 20 30510-5-05040-L5 40 8 x 20 30510-5-05040-R6 40 8 x 20 30510-5-06040-L6 40 8 x 20 30510-5-06040-R8 40 8 x 20 30510-5-08040-L8 40 8 x 20 30510-5-08040-R10 40 8 x 20 30510-5-10040-L10 40 8 x 20 30510-5-10040-R12 40 8 x 20 30510-5-12040-R

Technical detailsSolid T.C. head with centre point, two cutting edges and negatively ground spurs. Increased back relief angle. Spiralportion Teflon-coated, with landed flute. Parallel shank with clamping flat and length adjusting screw. The landed flute(heel) provides improved centering on return stroke and permits infinitely variable mounting of the countersinkdirectly on the spiral portion of the drill.

ApplicationFor use in adaptor chucks etc. on dowel hole drilling machines and CNC machines, to drill blind-holes in solid wood,various kinds of wood composites and boards etc., as well as in plastic laminated materials.


Allen screw 1039075-0-05080-R

with landed flute


PU = packing unit

Dowel Drill T.C.T.30566 parallel shank 10 mmDmm

L2mm

Shankmm

Part-No.


3 27 10 x 24 30566-6-03027-L3 27 10 x 24 30566-6-03027-R4 25 10 x 25 30566-5-04027-L4 25 10 x 25 30566-5-04027-R5 25 10 x 25 30566-5-05027-L5 25 10 x 25 30566-5-05027-R5,1 25 10 x 25 30566-5-05127-R6 25 10 x 25 30566-5-06027-L6 25 10 x 25 30566-5-06027-R7 25 10 x 25 30566-5-07027-L7 25 10 x 25 30566-5-07027-R8 22 10 x 25 30566-5-08027-L8 22 10 x 25 30566-5-08027-R


3 27 10 x 33 30566-6-03070-L3 27 10 x 33 30566-6-03070-R3,5 30 10 x 25 30566-6-03570-R4 35 10 x 25 30566-5-04035-L4 35 10 x 25 30566-5-04035-R4,5 35 10 x 25 30566-5-04535-L4,5 35 10 x 25 30566-5-04535-R5 35 10 x 25 30566-5-05035-L5 35 10 x 25 30566-5-05035-R5,5 35 10 x 25 30566-5-05535-L5,5 35 10 x 25 30566-5-05535-R6 35 10 x 25 30566-5-06035-L6 35 10 x 25 30566-5-06035-R6,5 35 10 x 25 30566-5-06535-L6,5 35 10 x 25 30566-5-06535-R7 35 10 x 25 30566-5-07035-L7 35 10 x 25 30566-5-07035-R7,5 35 10 x 25 30566-5-07535-R8 35 10 x 25 30566-5-08035-L8 35 10 x 25 30566-5-08035-R8,5 35 10 x 25 30566-5-08535-L8,5 35 10 x 25 30566-5-08535-R9 35 10 x 25 30566-5-09035-R9,5 35 10 x 25 30566-5-09535-R10 35 10 x 25 30566-5-10035-L10 35 10 x 25 30566-5-10035-R11 35 10 x 25 30566-5-11035-L11 35 10 x 25 30566-5-11035-R12 35 10 x 25 30566-5-12035-L12 35 10 x 25 30566-5-12035-R


5 45 10 x 25 30566-5-05045-L5 45 10 x 25 30566-5-05045-R6 45 10 x 25 30566-5-06045-L6 45 10 x 25 30566-5-06045-R6,5 45 10 x 25 30566-5-06545-R7 45 10 x 25 30566-5-07045-L7 45 10 x 25 30566-5-07045-R8 43 10 x 25 30566-5-08045-L8 43 10 x 25 30566-5-08045-R8,5 42 10 x 25 30566-5-08545-R9 42 10 x 25 30566-5-09045-L9 42 10 x 25 30566-5-09045-R10 42 10 x 25 30566-5-10045-L10 42 10 x 25 30566-5-10045-R11 45 10 x 25 30566-5-11045-L11 45 10 x 25 30566-5-11045-R12 45 10 x 25 30566-5-12045-L12 45 10 x 25 30566-5-12045-R

for through holes


PU = packing unit

Technical details60°V-point of solid T.C. Ø 3 and 3,5 mm with solid T.C. spiral portion and 120° V-point. Parallel shank with clamping flatand length adjusting screw. Spiral portion Teflon-coated up from Ø 4 mm.

ApplicationFor drilling through-holes in different kinds of wood composites and boards on various dowel hole boring machines(automatic boring machines, CNC machines, etc.). Ø 3 and 3,5 mm can also be used to drill blind-holes.




PU = packing unit

Dowel Drill T.C.T.30560 parallel shank 8 mm - with landed fluteDmm

L2mm

Part-No.Shankmm


5 25 30560-5-05030-L8 x 205 25 30560-5-05030-R8 x 208 25 30560-5-08030-L8 x 208 25 30560-5-08030-R8 x 20


5 35 30560-5-05040-L8 x 205 35 30560-5-05040-R8 x 208 35 30560-5-08040-R8 x 20

Technical details60° V-point of solid T.C. Parallel shank with clamping flat and length adjusting screw. Spiral portion with landed flute,Teflon-coated for reduced friction and better chip flow.

The landed flute (heel) provides improved centering on return stroke and permits infinitely variable mounting of thecountersink directly on the spiral portion of the drill.

ApplicationFor drilling through-holes in various kinds of wood composites and boards on automatic dowel hole boring machinesand CNC machines.

for through holes


PU = packing unit

Dowel Drill T.C.T.30567 parallel shank 10 mm - with landed fluteDmm

L2mm

Part-No.Shankmm


5 25 30567-5-05025-L10 x 205 25 30567-5-05025-R10 x 20


5 35 30567-5-05035-L10 x 255 35 30567-5-05035-R10 x 258 35 30567-5-08035-L10 x 258 35 30567-5-08035-R10 x 25

* Description see page 2.24.

Technical details60° V-point of solid T.C. Parallel shank with clamping flat and length adjusting screw. Spiral portion with landed flute,Teflon-coated for reduced friction and better chip flow.

The landed flute (heel) provides improved centering on return stroke and permits infinitely variable mounting of thecountersink directly on the spiral portion of the drill.

ApplicationFor drilling through-holes in various kinds of wood composites and boards on automatic dowel hole boring machinesand CNC machines.



for through holes


PU = packing unit

Dowel Drill - Solid T.C.30568 parallel shank 10 mmDmm

L2mm

L3mm

Shankmm

Part-No.


5 25 10 x 274,3 30568-6-05025-L5 25 10 x 274,3 30568-6-05025-R8 22 10 x 276,9 30568-6-08022-L8 22 10 x 276,9 30568-6-08022-R


5 35 10 x 274,3 30568-6-05035-L5 35 10 x 274,3 30568-6-05035-R8 35 10 x 276,9 30568-6-08035-L8 35 10 x 276,9 30568-6-08035-R10 33 10 x 278,7 30568-6-10033-L10 33 10 x 278,7 30568-6-10033-R

Technical detailsSolid T.C. spiral portion, with V-point 60°. Parallel shank with clamping flat and length adjusting screw.

ApplicationFor drilling through-holes in solid wood, various kinds of wood composites and boards on automatic dowel holes drillingmachines and CNC-machines. Especially recommended for drilling GFK, CFK, HPL (e.g. Trespa) and all commonkinds of wood composites.

• Increased tool life through wear resistant T.C. grade

• Little vibration stress through rigid solid T.C. design

• No break-outs when retracting the drill through non-stepped parallel spiral portion

• Finest ground spiral portion for improved chip flow

• Considerably increased regrinding area

Application dataR.P.M. = 6 000 - 9 000 min-1 vf = 0,5 - 4 m/min Reduce R.P.M. and feed rate for difficult ranges of materials (R.P.M. = 3000 - 4 000 m min-1 and vf = 0,5 - 1 m min-1). To increase the tool life and to improve the chip flow an add. JSO-Xcoating is possible. See page . Price on request.

for through holes


PU = packing unit

ISODUR Dowel Drill T.C.T.30570 parallel shank 10 mmDmm

L2mm

Part-No.Shankmm


5 27 30570-5-05027-L10 x 255 27 30570-5-05027-R10 x 258 24 30570-5-08027-L10 x 258 24 30570-5-08027-R10 x 25


4 35 30570-5-04035-L10 x 254 35 30570-5-04035-R10 x 255 35 30570-5-05035-L10 x 255 35 30570-5-05035-R10 x 256 35 30570-5-06035-L10 x 256 35 30570-5-06035-R10 x 257 35 30570-5-07035-L10 x 257 35 30570-5-07035-R10 x 258 35 30570-5-08035-L10 x 258 35 30570-5-08035-R10 x 2510 35 30570-5-10035-L10 x 2510 35 30570-5-10035-R10 x 25


5 45 30570-5-05045-L10 x 255 45 30570-5-05045-R10 x 258 43 30570-5-08045-L10 x 258 43 30570-5-08045-R10 x 25

Technical detailsSolid special grade T.C. head, with V-point and double bevel. Spiral portion Teflon-coated for reduced friction and betterchip flow. Parallel shank with clamping flat and length adjusting screw.

ApplicationFor drilling through-holes in different kinds of wood composites and boards on dowel hole drilling machines and CNCmachines.

• Considerably increased tool life compared with traditional T.C. dowel drills

• Set-up times can be enormously reduced for only small extra costs



for through holes


PU = packing unit

Dowel Drills with threaded shank T.C.T.30700-5 external thread M 8Dmm

L2mm

Part-No.L3mm

Drilling depth 45 mm

5 45 30700-5-05045-L635 45 30700-5-05045-R636 45 30700-5-06045-L636 45 30700-5-06045-R638 45 30700-5-08045-L638 45 30700-5-08045-R63

30705-5 external thread M 8 - with register 9 x 4 mmDmm

L2mm

Part-No.L3mm


8 40 30705-5-08040-L558 40 30705-5-08040-R55


8 60 30705-5-08060-L758 60 30705-5-08060-R75

30710-5 external thread M 10Dmm

L2mm

Part-No.L3mm


5 45 30710-5-05045-L635 45 30710-5-05045-R636 45 30710-5-06045-L636 45 30710-5-06045-R638 45 30710-5-08045-L638 45 30710-5-08045-R6310 45 30710-5-10045-L6310 45 30710-5-10045-R63


8 60 30710-5-08060-L808 60 30710-5-08060-R8010 60 30710-5-10060-L8010 60 30710-5-10060-R8012 60 30710-5-12060-L8012 60 30710-5-12060-R80

30715-5 external thread M 10 - V-point 60°Dmm

L2mm

Part-No.L3mm

5 40 30715-5-05040-L655 40 30715-5-05040-R65

Technical details No. 30700/30705/30710/30720Solid T.C. head with centre point, two cutting edges and negatively ground spurs. Increased back relief angle. Spiralportion Teflon-coated. (No. 30700/30710/30720).

ApplicationFor drilling accurate blind-holes and through-holes (No. 30715) in various kinds of wood composites and boards.

Technical details No. 3071560° V-point of solid T.C. Spiral portion Teflon-coated.


PU = packing unit


PU = packing unit

Dowel Drills T.C.T.30730-5 external thread M 10 - with register 11 x 4Dmm

L2mm

Part-No.L3mm

5 45 30730-5-05045-L635 45 30730-5-05045-R636 45 30730-5-06045-R638 45 30730-5-08045-L638 45 30730-5-08045-R6310 45 30730-5-10045-L6310 45 30730-5-10045-R63

30500 shank 6 mm - for Schleicher machinesDmm

L2mm

L1mm

Shankmm

Part-No.

6 35 6 x 3076 30500-5-06035-R10 35 6/10 x 2886 30500-5-10035-R

Technical detailsSolid T.C. head with two cutting edges and centre point. Negatively ground spurs and increased back relief. Spiralportion Teflon-coated. No. 30500: spiral portion with landed flute. Parallel shank with clamping flat, up from D = 8 mmwith additional collar D = 10 mm.

ApplicationFor drilling accurate blind-holes in solid wood and wood composites and boards.


PU = packing unit

Dowel Drills T.C.T.26180-5 centre point and spursDmm

L2mm

Part-No.L1mm

5 47 26180-5-05047-L805 47 26180-5-05047-R806 47 26180-5-06047-R808 47 26180-5-08047-L808 47 26180-5-08047-R8010 47 26180-5-10047-R80

26190 V-pointDmm

L2mm

Part-No.L1mm

5 28 26190-5-05028-L615 28 26190-5-05028-R61

Technical details No. 26180-5Solid T.C. head with two cutting edges, with centre point and negatively ground spurs and increased back reliefangle (same as No. 30500). Spiral portion Teflon-coated.

ApplicationFor drilling accurate blind-holes (No. 26180) and through-holes (No. 26190) in wood composites and boards.

internal thread M 10


PU = packing unit

Hinge Boring Bits T.C.T. Z2+V230300Dmm

L2mm

Shankmm

Part-No.


15 55,5 10 x 26 30300-5-15057-L15 55,5 10 x 26 30300-5-15057-R18 55,5 10 x 26 30300-5-18057-L18 55,5 10 x 26 30300-5-18057-R20 55,5 10 x 26 30300-5-20057-L20 55,5 10 x 26 30300-5-20057-R22 55,5 10 x 26 30300-5-22057-R25 55,5 10 x 26 30300-5-25057-L25 55,5 10 x 26 30300-5-25057-R26 55,5 10 x 26 30300-5-26057-R30 55,5 10 x 26 30300-5-30057-R34 55,5 10 x 26 30300-5-34057-R35 55,5 10 x 26 30300-5-35057-L35 55,5 10 x 26 30300-5-35057-R40 55,5 10 x 26 30300-5-40057-R


15 68 10 x 26 30300-5-15070-L15 68 10 x 26 30300-5-15070-R18 68 10 x 26 30300-5-18070-L18 68 10 x 26 30300-5-18070-R20 68 10 x 26 30300-5-20070-L20 68 10 x 26 30300-5-20070-R24 68 10 x 26 30300-5-24070-R25 68 10 x 26 30300-5-25070-L25 68 10 x 26 30300-5-25070-R30 68 10 x 26 30300-5-30070-L30 68 10 x 26 30300-5-30070-R34 68 10 x 26 30300-5-34070-R35 68 10 x 26 30300-5-35070-L35 68 10 x 26 30300-5-35070-R


35 75 10 x 26 30300-5-35077-R

Special design for through-holes see page 2.34.

30301 with reduced centre pointDmm

L2mm

Shankmm

Part-No.


15 68 10 x 26 30301-5-15070-L15 68 10 x 26 30301-5-15070-R19 68 10 x 26 30301-5-19070-L19 68 10 x 26 30301-5-19070-R35 68 10 x 26 30301-5-35070-R



Technical detailsTwo T.C.T. cutting edges, two inserted spurs andcentre point. Parallel shank with clamping flat andlength adjusting screw. Diamond (PCD) hinge boringbits see type 30300-9 on page .

ApplicationFor drilling accurate and clean-cut blind-holes inhardwood, various kinds of wood composites andboards etc. (for furniture fittings etc.). No. 30301: Withreduced centre point. To drill blind-holes for hingesclose to the lower surface layer.


PU = packing unit

Hinge Boring Bits T.C.T. Z3+V330320/30330Dmm

L2mm

L1mm

Shankmm

Part-No.

With centre point

25 55,5 10 x 2657,5 30320-5-25000-L35 55,5 10 x 2657,5 30320-5-35000-L35 55,5 10 x 2657,5 30320-5-35000-R

Without centre point

25 55,5 10 x 26- 30330-5-25000-L25 55,5 10 x 26- 30330-5-25000-R26 55,5 10 x 26- 30330-5-26000-R35 55,5 10 x 26- 30330-5-35000-R38 55,5 10 x 26- 30330-5-38000-L

* Description on page 2.29.

Technical detailsNo. 30320 with three cutting edges, three inserted spurs and centre point.No. 30330 with three cutting edges, three inserted spurs, without centre point. Both with parallel shank and lengthadjusting screw.

ApplicationFor drilling accurate and clean cut blind-holes in hardwood, various kinds of wood composites and boards etc. (forfurniture fittings etc.), on hinge boring machines, drilling machines or on CNC machines.




PU = packing unit

Hinge Boring Bit Set T.C.T. for Double-head hinges30305Dmm

L1mm

Type Part-No.RotationShankmm

30 57,5 rh./lhA 30305-5-30000-010 x 2634 57,5 rh./lhA 30305-5-34000-010 x 2634 57,5 rh./lhB 30305-5-34001-010 x 26

Single drills

30 57,5 rightA 30305-5-30000-R10 x 2630 57,5 leftA 30305-5-30000-L10 x 2634 57,5 rightA 30305-5-34000-R10 x 2634 57,5 leftA 30305-5-34000-L10 x 2634 57,5 rightB 30305-5-34001-R10 x 2634 57,5 leftB 30305-5-34001-L10 x 26

Technical detailsSet consisting of 1 pc each left-hand and right-hand T.C.T. hinge boring bit. Two cutting edges, two inserted spurs andcentre point. Parallel shank with clamping flat and length adjusting screw.

ApplicationFor drilling precise, blind-holes for double-head hinges (e.g. GU-JET-T-SOLO), as well as for corner fittings and scissorfittings in wooden windows on the following corner fitting drilling machines.

Type A: for Striffler, Ganner, Götzinger, Hess, Schafberger a. Sprödhuber, etc. machines. Type B: for Weinig-Unirex,Weinig-Conturex, Koch machines.


PU = packing unit

Hinge Boring Bits with threaded shank T.C.T. Z2+V230390 external thread M 10Dmm

L2mm

Part-No.L1mm

20 63 30390-5-20000-R7825 63 30390-5-25000-R78

Technical detailsTwo T.C.T. cutting edges, two inserted spurs and centre point.

ApplicationFor drilling accurate and clean cut blind-holes in hardwood, various kinds of wood composites and boards, etc. (forfurniture fittings etc.).


PU = packing unit

Hinge Boring Bit with reversible T.C. tips Z2+V222605Dmm

L2mm

L1mm

Shankmm

Part-No.

25 55,5 10 x 3057,5 22605-5-25575-R30 55,5 10 x 3057,5 22605-5-30575-R35 55,5 10 x 3057,5 22605-5-35575-R25 68 10 x 3070 22605-5-25700-R30 68 10 x 3070 22605-5-30700-R35 68 10 x 3070 22605-5-35700-L35 68 10 x 3070 22605-5-35700-R

Technical detailsTwo reversible T.C. raker tips and two reversible spurs. Adjustable centre point for drilling depths close to lower surfacelayer if necessary. Raker tips fixed with counter sunk screws for perfect chip removal. Shank with clamping flat andlength adjusting screw.

ApplicationFor drilling accurate and clean cut blind-holes in all common board materials, soft- and hardwood (e.g. for furniturefittings). * With chip breaking grooves for reduced feed force available on request .

• Without disturbing clamping screws in the chip space and therefore barrier free chip flow

• Ouick and easy unimpeded tip change


PU = packing unit

Cylinder Boring Bit T.C.T. Z2+V230100-5Dmm

L1mm

Part-No.Shankmm

10 90 30100-5-01000-R10 x 6212 90 30100-5-01200-R10 x 6213 90 30100-5-01300-R10 x 6214 90 30100-5-01400-R10 x 6215 90 30100-5-01500-R10 x 6216 90 30100-5-01600-R10 x 6217 90 30100-5-01700-R10 x 6218 90 30100-5-01800-R10 x 6219 90 30100-5-01900-R10 x 6220 90 30100-5-02000-R10 x 6221 90 30100-5-02100-R10 x 6222 90 30100-5-02200-R10 x 6223 90 30100-5-02300-R10 x 6224 90 30100-5-02400-R10 x 7425 90 30100-5-02500-R10 x 7426 90 30100-5-02600-R10 x 7427 90 30100-5-02700-R10 x 7428 90 30100-5-02800-R10 x 7430 90 30100-5-03000-R10 x 7432 90 30100-5-03200-R10 x 7434 90 30100-5-03400-R10 x 7435 90 30100-5-03500-R10 x 7436 90 30100-5-03600-R10 x 3038 90 30100-5-03800-R10 x 3040 90 30100-5-04000-R10 x 3042 90 30100-5-04200-R10 x 3045 90 30100-5-04500-R10 x 3047 90 30100-5-04700-R10 x 3048 90 30100-5-04800-R10 x 3050 90 30100-5-05000-R10 x 30

Technical detailsTwo cutting edges and centre point. Up to Ø 13 mm with spurs on plunge tips, from Ø 14 mm with two inserted spurs.Parallel shank. Right-hand rotation.

ApplicationFor drilling accurate holes in hardwood, various kinds of wood composites and boards, compressed wood, etc.

short design


PU = packing unit

Cylinder Boring Bit T.C.T. Z2+V230110-5 parallel shankDmm

L1mm

Part-No.Shankmm

20 140 30110-5-02000-R13 x 10522 140 30110-5-02200-R13 x 10524 140 30110-5-02400-R13 x 10525 140 30110-5-02500-R13 x 10328 140 30110-5-02800-R13 x 10330 140 30110-5-03000-R13 x 10335 140 30110-5-03500-R16 x 10340 140 30110-5-04000-R16 x 10345 140 30110-5-04500-R16 x 12050 140 30110-5-05000-R16 x 118

Special peak design for through-holes on page 2.34

Technical detailsTwo cutting edges, two inserted spurs, centre point. Parallel shank. Right-hand rotation.

ApplicationFor drilling accurate holes in hardwood, various kinds of wood composites and boards, compressed wood etc.

long design


PU = packing unit

Twist Drill HS30130/30132 common shank and drilling diameterDmm

L2mm

Part-No.L1mm

2 22 30130-4-02000-L492 22 30130-4-02000-R492,5 25 30130-4-02500-L572,5 25 30130-4-02500-R573 33 30130-4-03000-L603 33 30130-4-03000-R603,5 39 30130-4-03500-L703,5 39 30130-4-03500-R704 43 30130-4-04000-L754 43 30130-4-04000-R754,5 47 30130-4-04500-L804,5 47 30130-4-04500-R805 52 30130-4-05000-L855 52 30130-4-05000-R855,5 57 30130-4-05500-R926 57 30130-4-06000-L926 57 30130-4-06000-R926,5 63 30130-4-06500-R1007 69 30130-4-07000-R1087,5 69 30130-4-07500-R1088 75 30130-4-08000-L1158 75 30130-4-08000-R1158,5 75 30130-4-08500-R1159 80 30130-4-09000-R12510 87 30130-4-10000-R130

Extra length

4 100 30132-4-04000-R1505 100 30132-4-05000-R1506 100 30132-4-06000-R1508 100 30132-4-08000-R15010 100 30132-4-10000-R150

Technical detailsWith centre point and spurs. Particularly large flutes for better chip removal. Special coating for improved life time andagainst rust.

ApplicationFor drilling accurate blind-holes and through-holes in soft and hardwood. Solid tungsten carbide design see No. 30120-6(page 2.9).


PU = packing unit

Twist Drill T.C.T.30140-5 common shank and drilling diameterDmm

L2mm

Part-No.L1mm

5 35 30140-5-05035-L705 35 30140-5-05035-R706 35 30140-5-06035-R708 35 30140-5-08035-R7010 35 30140-5-10035-L7010 35 30140-5-10035-R70

Extra length

4 55 30140-5-04055-R804,5 60 30140-5-04560-R855 60 30140-5-05060-R905,5 65 30140-5-05565-R1006 65 30140-5-06065-R1006,5 70 30140-5-06570-R1107 70 30140-5-07070-R1108 75 30140-5-08075-R1208,5 80 30140-5-08580-R1309 80 30140-5-09080-R13010 90 30140-5-10090-R14011 95 30140-5-11095-R15012 100 30140-5-12100-R155

Technical detailsSolid T.C. head with centre point, two cutting edges and negatively ground spurs. Increased back relief angle (ill.on page 2.38). Spiral portion Teflon coated, with landed flute.* * The landed flute (heel) provides improvedcentering on return stroke and permits infinitely mounting of countersinks directly on the spiral portion of thedrill.

ApplicationEspecially recommended for drilling accurate blind-holes and through-holes in all kinds of wood, wood composites andboards, due to landed flute.

Please also see No. 30120-6 (page 2.9) for D = 5 mm below.

with landed flute


PU = packing unit

Twist Drill T.C.T.30150-5 parallel shank 13/16 x 50 mmDmm

L2mm

L1mm

Shankmm

Part-No.

6 75 13 x 50140 30150-5-06000-R8 85 13 x 50150 30150-5-08000-R10 95 13 x 50160 30150-5-10000-R12 105 13 x 50170 30150-5-12000-R13 110 13 x 50175 30150-5-13000-R14 115 13 x 50180 30150-5-14000-R15 120 13 x 50185 30150-5-15000-R16 125 16 x 50190 30150-5-16000-R18 130 16 x 50200 30150-5-18000-R20 140 16 x 50210 30150-5-20000-R

Technical detailsSolid T.C. head with centre point, two cutting edges and negatively ground spurs. Inceased back relief angle. Spiralportion Teflon-coated, with landed flute.

The landed flute (heel) provides improved centering on return stroke and permits infinitely mounting of the countersinkdirectly on the spiral portion of the drill.

ApplicationEspecially recommended for drilling accurate blind-holes and through-holes in all kinds of wood, wood composites andboards, due to landed flute vibration-free running.

with landed flute


PU = packing unit

Twist Drill - Solid T.C.30155-6 parallel shankDmm

L2mm

L3mm

Part-No.L1mm

Shankmm

8 70 1133,5 30155-6-08070-L10 x 258 70 1133,5 30155-6-08070-R10 x 258 90 1333,5 30155-6-08090-L10 x 258 90 1333,5 30155-6-08090-R10 x 2510 70 1133,5 30155-6-10070-L10 x 2510 70 1133,5 30155-6-10070-R10 x 2510 90 1333,5 30155-6-10090-L10 x 2510 90 1333,5 30155-6-10090-R10 x 25

Technical detailsSolid T.C., two raker edges, two spurs, extra long centre point. Polished flutes for perfect chip removal, with JSO-XD-coating for improved life time. Parallel shank with clamping flat for use in Weldon clamping chucks.

ApplicationFor drilling very deep and exceptionally accurate holes without emptying between. Especially applicable to drillingconnection- and dowel holes in frame- and window production. Also perfect for drilling holes in oblique work-pieces. Forsoft and hardwood, glued wood as well as for wood in window production. In long-grain and end-grain. Applicationdata: R.P.M = 4 500 - 6 000 vf = 2 - 3 m/min It is necessary to determine the optimum feed rate within the specificrange, depending on the material to be worked on.

with landed flute


PU = packing unit

Stockade Drill HS30175-4 parallel shankDmm

L2mm

L4mm

Part-No.L1mm

Shankmm

12 105 17010,0 30175-4-12000-R13 x 5014 115 18012,5 30175-4-14000-R13 x 5016 125 19013,0 30175-4-16000-R13 x 5018 130 20016,0 30175-4-18000-R13 x 5020 140 21016,5 30175-4-20000-R13 x 5022 150 22016,5 30175-4-22000-R13 x 5024 160 23518,0 30175-4-24000-R13 x 5025 170 25018,5 30175-4-25000-R13 x 50

Technical detailsTwo cutting edges, two spurs and extra long centre point. Spiral portion with landed flute. Stepped parallel shank 13 x50 mm. Right-hand rotation.

ApplicationFor drilling holes in oblique work-pieces, e.g. holes for stockades in stair production. To be used with jigs or drillingattachments for stockade holes. For hardwood or exotic wood please use T.C. design No. 30175-5 for longer tool life.

with landed flute


PU = packing unit

Countersink Z230755-5 T.C.T.dmm

Dmm

L1mm

Shankmm

Part-No.

3 15 10 x 3058 30755-5-03000-L3 15 10 x 3058 30755-5-03000-R3,5 15 10 x 3058 30755-5-03500-R4 15 10 x 3058 30755-5-04000-L4 15 10 x 3058 30755-5-04000-R4,5 15 10 x 3058 30755-5-04500-L4,5 15 10 x 3058 30755-5-04500-R5 15 10 x 3058 30755-5-05000-L5 15 10 x 3058 30755-5-05000-R5,5 15 10 x 3058 30755-5-05500-R6 15 10 x 3058 30755-5-06000-L6 15 10 x 3058 30755-5-06000-R

Technical detailsTwo cutting edges. Countersink angle 90°. Parallel shank 10 x 30 mm.

ApplicationTo be used in conjunction with parallel shank twist drills No. 30130 page 2.36, No. 30140 page and No. 30120 page2.9.

with parallel shank


PU = packing unit

Countersink solid T.C. Z324545Dmm

Angle L3mm

Part-No.L1mm

Shankmm

14 60° 62,512 24545-5-14060-R1014 60° 62,512 24546-5-14060-R1214 90° 55,57 24545-5-14001-R10*14 90° 707 24545-5-14002-R10*14 90° 587 24545-5-14003-R1014 90° 62,57 24546-5-14090-R12

Technical details:Three solid T.C. edges, precise centre point on bottom. Right-hand rotation.

* With clamping flat and length adjusting screw

ApplicationFor countersinking of pre-drilled holes. Can also be used as decorative groove and bevelling cutter.


PU = packing unit

Loose Countersink T.C.T. Z230650-5dmm

Dmm

Part-No.L1mm

3 15,5 30650-5-03000-R16,54 15,5 30650-5-04000-L16,54 15,5 30650-5-04000-R16,55 15,5 30650-5-05000-L16,55 15,5 30650-5-05000-R16,56 15,5 30650-5-06000-L16,56 15,5 30650-5-06000-R16,57 15,5 30650-5-07000-L16,57 15,5 30650-5-07000-R16,58 15,5 30650-5-08000-L16,58 15,5 30650-5-08000-R16,59 15,5 30650-5-09000-R16,510 20 30650-5-10000-L16,510 20 30650-5-10000-R16,512 20 30650-5-12000-R16,5

Technical details/ApplicationTwo T.C.T. cutting edges, countersink angle 90°. To be used in conjunction with twist drills and dowel drills with landedflute Nos. 30510/30530/ 30150/ 30140/ 30145/ 30500/ 30567. To be clamped directly onto the spiral portion of the drill.


Allen screw 1039070-0-06040-R


PU = packing unit

Loose Countersink T.C.T. Z230660 for shank clampingdmm

Dmm

L1mm

For drillsdiameter

Part-No.

10 15,5 5 - 1016,5 30660-5-15500-L10 15,5 5 - 1016,5 30660-5-15500-R10 20 5 - 1017,5 30660-5-20001-L10 20 5 - 1017,5 30660-5-20001-R

Technical details/ApplicationTwo T.C.T. cutting edges, countersink angle 90°. To be clamped onto the extended shank of drills No. 30540-5 (page2.13).


Allen screw M 6 x 4 ISO 4029 (for D = 15,5/20 mm) 1039070-0-06040-RAllen screw M 6 x 5 ISO 4029 (for D = 22 mm) 1039070-0-06050-R


PU = packing unit

Copying Cutter HS (HSS-E) Z125213-4Dmm

L2mm

L3mm

Part-No.L1mm

Shankmm

Form A

3 12 60- 25213-4-03012-R84 12 60- 25213-4-04012-R88 14 80- 25213-4-08014-R88 14 120- 25213-4-08120-R810 14 80- 25213-4-10014-R812 14 80- 25213-4-12014-R8

Form B

5 18 8035 25213-4-05035-R85 16 9045 25213-4-05045-R86 16 9045 25213-4-06045-R88 14 10068 25213-4-08068-R8

Technical detailsOne helical HS cutting edge. Cutting on bottom and periphery. Type B with narrow neck. Right-hand rotation.

ApplicationFor grooving, slotting and aperture operations in aluminium and plastic materials. For use on copying machines, e.g.Elumatec, Haffner, Rotox, Striffler, Wegoma, etc.

for working aluminium or plastics


PU = packing unit

Water Slot Cutters HS (HSS-E)25217/25218 helical designDmm

L2mm

L1mm

Part-No.ZShankmm

5 35 180 25217-4-05035-R85 40 1100 25217-4-05040-R86 40 1100 25217-4-06040-R8

25220/25221 straight designDmm

L2mm

Part-No.L1mm

Z

With V-point

5 10055 25221-4-05055-R1

Technical detailsNo. 25217/25218: helical design with either one or two cutting edges.No. 25220/25221: straight design, with one cutting edge.No. 25221: with V-point.Right-hand rotation.

ApplicationFor use on copying and water slot machines, e.g. Elumatec, Haffner, Rotox, Striffler, Wegoma, etc. No. 25221especially recommendable for extrusions in plastics (PVC).


PU = packing unit

Quick-Change Adaptors21300 Drill holderdmm

Dmm

Part-No.ELmm

10 17,8 21300-0-10175-017,5

21312-21340 Machine adaptorsdmm

amm

Part-No.Machine

Ill. No. 1

10 22,5 21312-0-10000-RNottmeyer (former design)10 22,5 21312-0-10000-LNottmeyer (former design)

Ill. No. 2

10 20 21314-0-10000-RBrema, Nottmeyer (newdesign)

10 20 21314-0-10000-LBrema, Nottmeyer (newdesign)

Ill. No. 3

10 22,5 21316-0-10000-RAyen, Holzma, Mayer,Torwegge, etc.

10 22,5 21316-0-10000-LAyen, Holzma, Mayer,Torwegge, etc.

Ill. No. 4

10 22,5 21322-0-10000-RBiesse, Busellato,Morbidelli, Torwegge,Weeke, etc.

10 22,5 21322-0-10000-LBiesse, Busellato,Morbidelli, Torwegge,Weeke, etc.

Ill. No. 5

10 45 21340-0-10000-RScheer10 45 21340-0-10000-LScheer

Technical details/ApplicationTwo-piece design, consisting of machine adaptor and drill holder, providing a system for quick changing of boring bits,adaptable to a variety of different spindle nose designs. Two clamping screws.


Lubricating grease in tin 121460-0-00000-0Socket spanner for machine adaptor 139073-0-00800-0Allen screw 1039070-0-05040-RAllen key SW 2,5, hexagon 539120-0-02500-0Plastic protection cap for d =10 mm 1021450-0-10000-0Plastic protection cap for d = 8 mm 1021450-0-08000-0


PU = packing unit

Adaptors21250 - 21280dmm

L1 amm mm

Part-No.Machine

Ill. No. 1

10 55 7 21250-0-10000-0D = 19 mm

Ill. No. 2

10 40 5 21252-0-10040-RNottmeyer (former design)10 40 5 21252-0-10040-LNottmeyer (former design)

Ill. No. 3

10 40 5 21254-0-10040-RBrema, Nottmeyer (newdesign)

10 40 5 21254-0-10040-LBrema, Nottmeyer (newdesign)





Ill. No. 4

10 40 5 21256-0-10040-RAyen, Biesse, Holzma,Mayer, Torwegge, etc.

10 40 5 21256-0-10040-LAyen, Biesse, Holzma,Mayer, Torwegge, etc.

8 40 5 21256-0-08040-RAyen, Biesse, Holzma,Mayer, Torwegge, etc.

8 40 5 21256-0-08040-LAyen, Biesse, Holzma,Mayer, Torwegge, etc.

Ill. No. 5

10 41 5 21262-0-10041-RBiesse, Busellato,Morbidelli, Torwegge,Weeke, etc.

10 41 5 21262-0-10041-LBiesse, Busellato,Morbidelli, Torwegge,Weeke, etc.

8 41 5 21262-0-08041-RBiesse, Busellato,Morbidelli, Torwegge,Weeke, etc.

8 41 5 21262-0-08041-LBiesse, Busellato,Morbidelli, Torwegge,Weeke, etc.

Ill. No. 6

10 51 8,5 21270-0-10051-RBilek, type K and N10 51 8,5 21270-0-10051-LBilek, type K and N

Ill. No. 7

10 47 9,3 21272-0-10047-RAlberti, Balestrini, Bilek,Schleicher, Vitap, etc.

10 47 9,3 21272-0-10047-LAlberti, Balestrini, Bilek,Schleicher, Vitap, etc.

Ill. No. 8

10 46 27 21280-0-10046-RScheer10 46 27 21280-0-10046-LScheer

Technical details/ApplicationDesigned as an adaptor chuck between spindle nose and drill shank. Two clamping screws. D = 19 mm (d = 10 mm),resp. D = 15,5 mm (d = 8 mm).


Allen screw 1039070-0-06040-RAllen key 539120-0-03000-0


PU = packing unit

Quick-Change Adaptor21480 JSOFIXDmm

dmm

L1mm

Part-No.Shankmm

20 10 M 756,5 21480-0-21256-R920 10 M 756,5 21480-0-21256-L920 10 M 856,5 21480-0-21156-R920 10 M 856,5 21480-0-21156-L920 10 M 1056,5 21480-0-21056-R1120 10 M 1056,5 21480-0-21056-L11

Technical detailsRetention mechanism with sliding sleeve and magnet-assisted clamping.

ApplicationFor keyless changing of drilling tools with 10 mm shank diameter, clamping flat and standard length adjusting screw.Chuck without built-in drilling tools must be covered against pollution with optional available dust protection bolts.

Specific advantages:

• Insertion assisted by magnetism

• Powerful but short stroke of the sliding sleeve

• Improved concentricity

• Smooth running

• Special length adjusting screw not necessary

Please ask for our special JSOFIX leaflet.


PU = packing unit

Quick-Change Adaptors21290-21296dmm

D2mm

D1mm

L1mm

Part-No.

For Weeke, Ill. No. 1

10 17,2 4620 21290-0-10000-0

For Biesse, Ill. No. 2

10 - 3720 21295-0-10000-R10 - 3720 21295-0-10000-L

For Grass, Ill. No. 3

10 - 3920 21296-0-10000-0


Allen screw M 6 x 5 ISO 4029 (for Weeke/Grass) 1039070-0-06050-RAllen screw M 6 x 6 ISO 4029 (for Biesse) 1039070-0-06060-RAllen key 539120-0-03000-0


PU = packing unit

Bushings for Twist Drills39220 Split adaptor bushdmm

Dmm

Part-No.L1mm

2 10 39220-0-02000-0232,5 10 39220-0-02500-0233 10 39220-0-03000-0233,5 10 39220-0-03500-0234 10 39220-0-04000-0235 10 39220-0-05000-0236 10 39220-0-06000-023

39225 Adaptor bush with parallel shankdmm

Dmm

L1mm

Shankmm

Part-No.

2 15 10 x 2140 39225-0-02000-02,5 15 10 x 2140 39225-0-02500-03 15 8 x 1938 39225-0-03008-03 15 10 x 2140 39225-0-03000-03,5 15 10 x 2140 39225-0-03500-04 15 10 x 2140 39225-0-04000-05 15 10 x 2140 39225-0-05000-0

Technical details/ApplicationTo take twist drill No. 30120 and boring pin No. 20005 (page 2.10). Shank with clamping flat, without length adjustingscrew. Can be used for either right-hand or left-hand rotation.


Allen screw 1039070-0-06050-RAllen key 539120-0-03000-0


PU = packing unit

drill and boring bits, adapters · drill and boring bits, adapters 800-544-8436

Documents