dt607 series - sambo hellas 2easy ... 2 wire /dt607_en.pdf · user manual dt-eng-dt607-v1 / 201607...

USER MANUAL

DT-ENG-DT607-V1 / 201607

• Please read this manual carefully to ensure safe and correct operation.

• Keep this manual well for future reference.

RF CARD

RF CARD

RF CARD

RF CARD

RF CARD

RF CARD

DT607A/ID-S4DT607/ID/FE-S1 DT607/ID/FE-S2

DT607F/ID/FE-S4DT607/ID/FE-S3 DT607/ID/FE-S4

DT607 Series

2 WIRE SYSTEM

Fisheye door station with proximity access control

CONTENTS

PARTS AND FUNCTIONS ..................................................................................... 3

Part Names............................................................................................................. 3

Mounting ................................................................................................................. 4

BASIC FUNCTIONS .............................................................................................. 6

Unlock Operations .................................................................................................. 6

Fisheye Camera ..................................................................................................... 6

External Motion Detection ...................................................................................... 6

SETUP INSTRUCTIONS ........................................................................................ 7

Functions Setting Up .............................................................................................. 7

Setting Door Station Address ................................................................................. 8

Setting Door Station Calling Mode ......................................................................... 8

Setting Camera Resolution.................................................................................... 10

Setting Unlock Mode ............................................................................................. 10

Setting Unlock Time............................................................................................... 11

Setting Nameplate Illumination Mode .................................................................... 11

Setting Night View LED Illumination Mode ............................................................ 12

Setting Ring-back Tone ......................................................................................... 12

Setting Image Display Mode.................................................................................. 13

Registering ID Card ............................................................................................... 14

WIRING ................................................................................................................. 17

Connecting Electric Lock ....................................................................................... 17

Connecting Basic One-to-one ............................................................................... 18

Connecting Multi Door Stations ............................................................................. 18

Connecting Multi Monitors ..................................................................................... 19

APPENDIX ............................................................................................................ 21

Precautions............................................................................................................ 21

Specification .......................................................................................................... 21

Cables and Requirments ....................................................................................... 22

-3-

Part Names

PARTS AND FUNCTIONS

[11]

[10]

[14]

[9]

[1]

[3]

[4]

[1]

[3]

[4]

[8]

[7]

[6]

[5]

[9]

[8]

[7]

[6]

[5]

[12]

[11]

[12]

[13]

[13]

[2]

[2]

Surface mounted

Flush mounted

[1] Microphone

[2] UNLOCK indicator

[3] CALL indicator

[4] Call button

[5] Nameplate

[6] Front panel

[7] Speaker

[8] Night view LED

[9] Camera lens

[10] Rainy cover

[11] Mounting hook

[12] Connection port

[13] Screw hole

[14] Mounting box

-4-

PARTS AND FUNCTIONS

Mounting

1 2 3 4 5

AcDbMLeader (ACDB_MLEADER_CLASS)


Rainy cover

Rainy cover

The distance between the top of main unit and rain cover should be not less than 3mm.

Main unitMain unit

≥3mm

1 2 3 4 5




1. Connect the cable correctly.2. Drill holes in the wall to match the size of screw stoppers,then attach the rainy cover and main unit to the wall, and the distance between the top of main unit and rain cover should be not less than 3mm.3. Install the name plate. 4. Attach the front panel to the main unit.5. Use the special screwdriver and the screws to fix the panel.

1. Drill a hole in the wall to match the size of mounting box,then attach the mounting box to the wall.2. Loosen the high screws to install the name plate. 3. Connect the cable correctly.4. Attach the front panel to the mounting box,then use the special screwdriver and the screws to fix the panel.5. Finish the installation.

Surface mounted

Flush mounted

The installation height is suggested to 145~160cm.

* The camera angle view of surface mount model may be less than 1700.

v-tec

矩形

v-tec

矩形

-5-

PARTS AND FUNCTIONS

Terminal description

Lock Control Jumper: To select the lock type.

Motion Detector Connect Port: To connect external PIR motion detector.

Main Connect Port: To connect the bus line and the electronic locks.

• L1,L2: Connect to the bus line, no polarity.

• PL: External lock power input, connect to the power positive(power +).

• S+: Lock power(+) output.

• S-: Lock power(-) output, connect to the power(-) input of locks(only when using the door station to power the locks, if using the external power supply for the locks, the S- will not be connected).

1 2 3

Lock Control Jumper

PIR Motion DetectorConnect Port

+12V

GN

DP

IR

L1 L2 PL S+ S-Main Connect Port

-6-

BASIC FUNCTIONS

Unlock Operations

Unlocking of ID Card

When the registered user card has been shown to ID card window, the UNLOCK indicator lights up, the buzzer sounds,and the electric door strike is unlocked.

• If show the authorized user card,the buzzer will sound of beep+,and the UNLOCK indicator will light up.

• If show the unauthorized user card,the buzzer will sound of beep,beep,beep.

Fisheye Camera

External Motion Detection

Please note that this function requires the monitor with fisheye function to support.

The angle view is 1700,visitors in this angle view can be seen clearly and can be zoomed to see individuals up close via indoor monitor with fisheye function.

The door station is equipped with a terminal to connect external motion detector.

If the external motion detector is connected to the system,following functions will be effec-tive:

If detect someone passing by, the door station can be activated operation to unlock or turn on light.

Standarddoor station angle

DT6071700 door camera angle

(Wide angle view shown)

12V

Motion detector

GNDPIR

* Please contact with supplier for more details about detector connection.

-7-

SETUP INSTRUCTIONS

Functions Setting Up

KEY_1KEY_2KEY_3KEY_4KEY_SET

LED_UNLOCKLED_TALK

LED_NAME

RF CARD

This section explains the settings of each function,please refer to the following table:

To perform the settings for the function you want,you should move away the metal front panel. Please refer to the sketch map.

Each operation is indicated by the lighting up of the LED indicator on the unit, and by the sounding of the buzzer.

Order Setting items Setting range Default value

1 Setting door station address 0~3 0

2Setting door station

calling modeStandard/Group calling mode Standard calling mode

3 Setting camera resolution High/Low High

4 Setting the unlock mode 0:opened/1:closed 0:opened

5 Setting the unlock time 01 to 99 seconds 1 seconds

6Setting the nameplate

illumination modeOn/Off/Auto On

7Setting night view LED

illumination modeOn/Off/Auto Auto

8 Setting ring-back toneRinging one timeRing continuouslyNo ring-back tone

Ringing one time

9 Setting image display modeAlternate switching mode

Zoom modeFull screen mode

Alternate switching mode

-8-

Setting Door Station Address

Setting Door Station Calling Mode

Total 4 addresses can be configured. It can be modified either before or after installation.

0 is default, to change the setting, please follow the steps:

UNLOCK Indicator:OFFTALK Indicator:OFF

Buzzer Beep+, Beep


Buzzer Beep+

In standby mode, press KEY_SET button once

Press KEY_1 button to set the first door station.

Press KEY_2 button to set the second door station.

Press KEY_3 button to set the third door station.

Press KEY_4 button to set the fourth door station.


Buzzer Beep,Beep


Buzzer Beep,Beep,Beep


Buzzer Beep,Beep,Beep,Beep

ID=0,1st door station ID=1,2nd door station ID=2,3rd door station ID=3,4th door station

SETUP INSTRUCTIONS

• If setting mode has not been exited, you can change the address of door station by pressing KEY1~4 freely.

• The LED_NAME indicator will always blink until exit out the setting mode.

• If without any operation in 10 seconds, it will exit out setting mode automatically.

• In this step,press KEY_SET button four times to exit out the setting mode manually.

There are two calling modes for door station,Standard calling mode and Group calling mode.

Please know that the door station work in Standard calling mode by default.

-9-

• If setting mode has not been exited, you can change the calling mode by pressing KEY1 circularly.

• The LED_NAME indicator will blink all the time until exit out the setting mode.


• In this step,press KEY_SET button three times to exit out the setting mode manually.

SETUP INSTRUCTIONS

* More details about code setting for monitor, please refer to corresponding user manual .

Each call button will respond different addresses when set in different calling mode. Refer to the followings for more informations.

Call buttonA: call the monitor with address 01 by default.

Call buttonB: call the monitor with address 02 by default.

Call buttonC: call the monitor with address 03 by default.

Call buttonD: call the monitor with address 04 by default.

Call buttonA: Call all monitors in group address from 00~15.(one of the monitor should be set to 00)

Call buttonB,C,D: Call all monitors in group address from 16~31. (one of the monitor should be set to 16)

UNLOCK Indicator:OFFTALK Indicator:ON

Buzzer Beep+, Beep

In standby mode, press KEY_SET button twice.


Buzzer Beep+

Press KEY_1 button to activate Standard callingmode for door station.


Buzzer Beep, Beep

Press KEY_1 button again to activate Group calling mode for door station.

Press KEY_1

ABC

ABCD

RF CARDRF CARD

A ABRF CARDRF CARD

1.Standard calling mode(Address range 01-04

by default)

2.Group calling mode

To change this setting, please follow the steps:

-10-

Setting Camera Resolution

Setting Unlock Mode

The resolution of the camera can be adjusted at any time, that means the quality of image on screen can be set to high or low.

High resolution is default, to change the setting, please follow the steps:

There are 2 unlock modes, Normally opened and Normally closed.

Normally opened is default, to change the setting, please follow the steps:


Buzzer Beep+, Beep

In standby mode, press KEY_SET button twice.


Buzzer Beep+

Press KEY_2 button to set thecamera to High resolution.


Buzzer Beep, Beep

Press KEY_2 button again to set the camera to Lowresolution.

Press KEY_2

UNLOCK Indicator:ONTALK Indicator:OFF

Buzzer Beep+, Beep

In standby mode, press KEY_SET button three times.


Buzzer Beep+

Press KEY_1 button to set the unlock mode to Normally opened.


Buzzer Beep, Beep

Press KEY_1 button againto set the unlock mode to Normally closed.

Press KEY_1

SETUP INSTRUCTIONS

• If setting mode has not been exited, you can change the camera resolution by pressing KEY2 circularly.



• In this step,press KEY_SET button three times to exit out the setting mode manually.

• If setting mode has not been exited, you can change the unlock mode by pressing KEY1 circularly.



• In this step,press KEY_SET button twice to exit out the setting mode manually.

-11-

Setting Nameplate Illumination Mode

Setting Unlock Time

There are 3 illumination modes for nameplate indicator, Normally on,Normally off and Auto.

Normally on is default, to change the setting, please follow the steps:

By default, the unlock time is 1s, but it can be changed,the setting range is 1s~99s.

Follow the steps:

SETUP INSTRUCTIONS


Buzzer Beep+, Beep



Buzzer Beep,Beep......

Press and hold on KEY_2 button. The time you holdingon is the new unlock time.


Buzzer Beep+, Beep



Buzzer Beep+

Press KEY_3 button to set the nameplate illumination mode to Normally on.


Buzzer Beep, Beep

Press KEY_3 button againto set the nameplate illumina-tion mode to Normally off.


Buzzer Beep, Beep,Beep

Press KEY_3 button again and again to set the nameplate illumination mode to Auto.

Press KEY_3

• When entering time delayed setting, the buzzer sound one time every second.




• If setting mode has not been exited, you can change the nameplate illumination mode by pressing KEY3 circularly.




-12-

Setting Ring-back Tone

If allow ring-back tone, press the call button to call monitor, a ring-back call tone can be heard from door station.

There are 3 ring-back call tones, Ringing one time,Ringing continuously and No ring-back tone.

Ringing one time is default, to change the setting, please follow the steps:

Setting Night View LED Illumination Mode

There are 3 working modes for night view LED indicator, Normally on,Normally off and Auto.

Auto is default, to change the setting, please follow the steps:

SETUP INSTRUCTIONS


Buzzer Beep+, Beep



Buzzer Beep+

Press KEY_4 button to set the night view LED mode to Normally on.


Buzzer Beep, Beep

Press KEY_4 button againto set the night view LED mode to Normally off.



Press KEY_4 button againand again to set the night view LED mode to Auto.

Press KEY_4

UNLOCK Indicator:ONTALK Indicator:ON

Buzzer Beep+, Beep

In standby mode, press KEY_SET button four times.


Buzzer Beep+

Press KEY_1 button to set the ring-back call tone ringingone time.


Buzzer Beep, Beep

Press KEY_1 button againto set the ring-back call tone ringing continuously.



Press KEY_1 button againand again to close ring-backcall tone.

Press KEY_1

• If setting mode has not been exited, you can change the night view LED illumination mode by pressing KEY4 circularly.




• If setting mode has not been exited, you can change the ring-back tone by pressing KEY1 circularly.



• In this step,press KEY_SET button once to exit out the setting mode manually.

-13-

Setting Image Display Mode

Please know that this setting is only effective for monitors which does not support man-ual operation for pan-tilt.

When door station calls monitor,the image will be displayed on screen,there are 3 modes for im-age displayed, Alternate switching mode,Zoom mode and Full screen mode.

Alternate switching mode: when the monitor being called, switch at regular time(5s) between Full screen and Zoom image.

Zoom mode: when the monitor being called, the image will be displayed on full screen for 5 seconds, then switch to Zoom image.

Full screen mode: when the monitor being called, the image will be always displayed on Full screen.

Alternate switching mode is default, to change the setting, please follow the steps:

When answering the call, the image switching reminder can be activated or forbidden.

If set to activated mode, the image switching reminder will be different for different image display mode.

Alternate switching mode: When answering the call, image switching reminder is not effective.

Zoom mode: When answering the call, the image will be displayed on full screen for 5 sec-onds, then switch to Zoom image to remind to enter talking status.


Buzzer Beep+, Beep



Buzzer Beep+

Press KEY_2 button to set the image display mode to Cycle switching.


Buzzer Beep, Beep

Press KEY_2 button againto set the image display mode to Zoom mode.


Press KEY_2


Press KEY_2 button againand again to set the image display mode to Full screen.

During setting mode, press KEY-2 to switch Cycle switching mode, Zoom mode and Full screen mode in cycle.

SETUP INSTRUCTIONS

When the monitor being called

When answering the call

• If setting mode has not been exited, you can change the image display mode by pressing KEY2 circularly.




-14-


Buzzer Beep+, Beep



Buzzer Beep+

Press KEY_3 button to activate image switching when answering the call.


Buzzer Beep, Beep

Press KEY_3 button againto forbid image switchingwhen answering the call.

Press KEY_3

Registering ID Card

• Up to 320 user cards can be registered by the door station.

• Easy management with LED status and sound hints.

• There are two master cards, one MASTER CARD ADD card and one MASTER CARD DELETE card, When registered new master cards, the old master cards are invalid automatically.

• Card reading distance is less than 3cm.

• The master cards are necessary when you add or delete user cards. Please keep it well for future use.

• EM card, 125kHz.

Authorizing master cards:

By default,there are two master cards marked MASTER CARD ADD and MASTER CARD DELETE ,but you should know that the master card can be authorized by users at any time.That means any two user cards can be authorized to master cards,When registered new master cards, the old master cards will be invalid automatically.

SETUP INSTRUCTIONS

• If setting mode has not been exited, you can change the image display mode by pressing KEY3 circularly.




Full screen mode: When answering the call, the image will be displayed on Zoom mode for 5 seconds, then switch to Full screen to remind to enter talking status.

If set to forbidden mode, there is no image switching reminder at any image display mode.

Activated is default, to change the setting, please follow the steps:

-15-

SETUP INSTRUCTIONS

Switching Access Control:


Buzzer Beep+, Beep

Show the master card of MASTER CARD ADD to ID card window in standby.


Buzzer Beep+, Beep

Show the master card of MASTER CARD DELETE to ID card window.


Buzzer Beep+

Show the master card of MASTER CARD DELETEagain to switch as a door station access control.


Buzzer Beep+,Beep

Show the master card of MASTER CARD DELETEagain to switch to DT-ACCcontrolled.

The access can be controlled by door station or DT-ACC,so it’s available to switch the access function.


• If current access is controlled by door station, next access switching setting is controlled by DT-ACC.

UNLOCK Indicator:Blink two timesTALK Indicator:OFF

Buzzer Beep,Beep

Show the first card to ID card window, set the card of MASTER CARD ADD.

UNLOCK Indicator:Blink three timesTALK Indicator:OFF

Buzzer Beep,Beep,Beep

Show the second card to ID card window, set the card of MASTER CARD DELETE.


Buzzer Beep+, Beep

When power on in 10s,pressand hold on KEY_SET buttonfor 3s.

UNLOCK Indicator:Blink one timeTALK Indicator:OFF

Buzzer Beep+

Press KEY_2 button.

• The LED_NAME indicator will always blink until exit out the master card authorized mode.


• It will exit out setting mode automatically after showing these two cards,the UNLOCK&TALK indicator will be turned off.

-16-

Adding User Cards:


Buzzer Beep+, Beep

Show the master card of MASTER CARD ADD to ID card window in standby.

UNLOCK Indicator:OFFTALK Indicator:Blink one time

Buzzer Beep+

Show user cards to be added in sequence.


Buzzer Beep, Beep+

Show the master card of MASTER CARD ADD again to exit.


• To add user card, the access must be controlled by door station.

SETUP INSTRUCTIONS

Deleting User Cards:

Initializing Access (delete all user cards):


Buzzer Beep+, Beep

Show the master card of MASTER CARD DELETE to ID card window in standby.

UNLOCK Indicator:Blink one timeTALK Indicator:OFF

Buzzer Beep+

Show user cards to be deleted in sequence.


Buzzer Beep, Beep+

Show the master card of MASTER CARD DELETE again to exit.


Buzzer Beep+, Beep

Show the master card of MASTER CARD DELETE to ID card window in standby.


Buzzer Beep+, Beep

UNLOCK Indicator:Blink for some time

TALK Indicator:Blink for some time

Buzzer Beep

Show the master card of MASTER CARD ADD again,format is activated.

Show the master card of MASTER CARD ADD to ID card window.

• .If without any operation in 10 seconds, it will exit out setting mode automatically.




• At step3, the UNLOCK & TALK indicator will blink all time until formatting is finished.

• When formatting is finished, UNLOCK & TALK indicator will be turned off and sound “ Beep+ ”, and exit out setting mode automatically.

-17-

Connecting Electric Lock

Door Lock Controlled with Internal Power

Door Lock Controlled with Dry Contact

1.Electronic lock of Power-on-to-unlock type should be used.

2.The door lock is limited to 12V, and hold-ing current must be less than 250mA.

3.The jumper should be placed on position 2 and 3 before connecting.

4.The door lock control is not timed from Exit Button(EB).

5.The Unlock Mode must be set to 0 (by default).

1.The external power supply must be used according to the lock.

2.The inside relay contact is restricted to 230Vac 1A or 24Vdc 1A.

3.The jumper must be taken off before connecting.

4.Setup the Unlock Mode according to different lock types.

• Power-on-to-unlock type:Unlock Mode=0 (by default)

• Power-off-to-unlock type:Unlock Mode=1

EB*

LOCK

Jumper position on 2&3

1 2 3

L1 L2 PL S+ S-

Take off the jumper

1 2 3

L1 L2 PL S+ S-

LOCK

POWER SUPPLY

WIRING

* DT-RLC relay actuator is needed for 2nd lock connection.

-18-

WIRING

• Max.4 door stations can be connected to the system. • Ensure to set the correct address for each door station, Refer to Page 8 for more details

about the address setting of door stations.

Connecting Basic One-to-one

Connecting Multi Door Stations

BUS(IM) BUS(DS)

-

+

L1 L2 PL S+ S-

ID=0

Code=1, DIP6=on

1 2 3 4 5 6

ON DIP

L2

L1

DIP Switches

RF CARD

PC6A

AC~

100~240VAC

100~240VAC

DBC4A1

A B C D

OFF

ON

Impedance switch

BUS(IM) BUS(DS)

PC6A

AC~

ID=01st door station

ID=12nd door station

ID=23rd door station

ID=34th door station

L1 L2 PL S+ S- L1 L2 PL S+ S- L1 L2 PL S+ S- L1 L2 PL S+ S-

To monitors

RF CARD RF CARD RF CARD RF CARD

• The door station work in Standard mode in this situation. Refer to Page 9 in detail.• The door station is also compatible with other monitors which are provided by our company.

-19-

Basic IN-OUT Wiring in Standard Mode

Connecting Multi Monitors

WIRING

• The door station is also compatible with other monitors which are provided by our company.

• Please set door station into group calling mode if there is more than 4 monitors in villa(Refer to Page 9)

• Distributor is unnecessary in full audio system, and IN-OUT mode is recom-mended.

• For the last monitor connected to the system, DIP6 should set to ON.

ID=0

Code=1, DIP6=off

Optional functional module

SCU camera module(max.4)GSM module(mobile phone transfer)TPS module(PBX transfer)QSW image quad splitter module

(Master)

Code=1, DIP6=off(Slave 2)

Code=1, DIP6=on(Slave 3)

BUS(IM) BUS(DS)

PC6A

AC~

100~240VAC

Code=1, DIP6=off(Slave 1)

RF CARD

SCU GSM TPS QSW

-20-

• The door station is also compatible with other monitors which are provided by our company.

• It can be extended 3 slave monitors for each monitor.(Better use with extra distributor for the extension)

WIRING

DBC4A1

A B

C D

RLC DBC4A1

OFF ONImpedance switch

BUS(IM) BUS(DS)

Code=1，DIP6=on Code=2，DIP6=on

Code=3，DIP6=on Code=4，DIP6=on

ID=0

RF CARD

PC6A

AC~

100~240VAC

Optional functional module

BDU

BDU bus amplifier moduleRLC staircase light controller moduleDBC4A1 2/4 inputs branch distributor

Star Topology Wiring With DBC4A1 in Standard Mode

-21-

Precautions

Specification

• Please clean the unit with soft cotton cloth, don't use the organic impregnant or chemical clean agent. If necessary, please use a little pure water or dilute soap water to clean the dust.

• The unit is weather resistant. However do not spray high pressure water on access control keypad directly. Excessive moisture may cause problems with the unit.

• You must use the right adaptor which is supplied by the manufacture or approved by the manufacture.

• Pay attention to the high voltage inside the products, please refer service only to a trained and qualified professional.

APPENDIX

Power supply: DC 24V

Power consumption: Standby 0.8W; Working 3W

Camera lens: Color CMOS, 2.0 Mega pixel

1/2.7’’ fisheye camera,1700 wide angle

Lock Power supply: 12Vdc, 280mA(Internal Power);

Number of relay circuits: 2(the second lock need external device to support)

Mounting: Surface wall-mount / flush mount

Working temperature: -20ºC ~ +55ºC

Protection: IP54

Material: Zinc alloy panel(surface mounted)

Stainless steel panel(flush mounted)

Wiring: 2 wires, non-polarity

Dimension: 176(H)×90(W)×27(D)mm(surface mounted)

220(H)×119(W)×52(D)mm(flush mounted)

-22-

APPENDIX

Cables and Requirments

The maximum distance of the wiring is limited in the DT system. Using different cables may also affect the maximum distance which the system can reach.

Cable and distance(unit:m)

Cable Usage A B

≤2 IM

B

≤16 IM

Twisted cable 2x0.75mm2 60 100 40

Twisted cable 2x1mm2 80 120 60

A

B

RF CARD

PC6A

Basic IN-OUT Wiring Mode

-23-

B

A

C2

2

DBC4A1

RF CARD

PC6A

Cable and distance(unit:m)

Cable Usage A B C

Twisted cable 2x0.75mm2 60 60 30

Twisted cable 2x1mm2 80 80 40

APPENDIX

Star Topology Wiring Mode With DBC4A1

The design and specifications can be changed without notice to the user. Right to interpret and copyright of this manual are preserved.

DT-ENG-DT607-V1

dt607 series - sambo hellas 2easy ... 2 wire /dt607_en.pdf · user manual dt-eng-dt607-v1 / 201607...

Documents