duke duke energy corporation mcguire nuclear stationb01.020 head welds b01.021 circumferential 0...

Duke Duke Energy Corporation McGuire Nuclear Station

ft. EnetJy. 12700 Hagers Ferry Road Hunrersville, NC 28078-9340

H. B. Barron (704) 875-4800 OFFICE

Vice President (704) 875-4809 FAX

January 11, 2001

U. S. Nuclear Regulatory Commission Washington, D.C. 20555-0001

ATTENTION: Document Control Desk

Subject: McGuire Nuclear Station, Unit 2 Docket No. 50-370 Inservice Inspection Report End of Cycle 13 Refueling Outage

Please find attached the Inservice Inspection Report for inspections

conducted prior to the conclusion of the end of cycle 13 (EOC-13)

refueling outage for McGuire Nuclear Station (MNS), Unit 2. This

report is submitted pursuant to the filing requirements of Article

IWA-6000 of Section XI of the ASME Code.

Section 5.2 of the attached report lists the limited examination item

numbers for which a relief request will be submitted. Limited

examination relief request 01-001 is under development. Submittal of

relief request 01-001 to the NRC is considered a regulatory

commitment.

Article IWA-6000 establishes filing requirements for inservice

inspection summary reports. During a review of this report, Duke

identified that the filing requirements had not been satisfied for

some inspection items. Several of the documented inspection items in

this report were performed during a prior outage cycle. Therefore,

these items are being submitted beyond the time requirements of

Article IWA-6000. A licensee corrective action program report (PIP#

M-00-05032) was issued to address the administrative failure to

satisfy this ASME Code filing requirement.

Any questions on this matter should be directed to M. R. Wilder, MNS

Licensing and Compliance, at (704) 875-5362.

Sincerely,

/ B. Barron--

H. B. Barron

U.S. Nuclear Regulatory Commission January 11, 2001

Attachment

cc w/o att: Mr. L. A Reyes Regional Administrator, Region II U. S. Nuclear Regulatory Commission 101 Marietta Street, NW, Suite 2900 Atlanta, Georgia 30323

Mr. F. Rinaldi, Project Manager Office of Nuclear Reactor Regulation U. S. Nuclear Regulatory Commission One White Flint North, Mail Stop 9H3 Washington, D.C. 20555

S. M. Shaeffer Senior NRC ResidentInspector McGuire Nuclear Station

U.S. Nuclear Regulatory Commission January 11, 2001

bxc w/att: ELL (EC050) Master File: 1.3.8.1 - Routine Reports R.L. Gill, Jr. (ECl2R)

bxc w/o att: Kay L. Crane (MG01RC) Gary D. Gilbert (CN01RC) Charles J. Thomas (EC050) Lisa Vaughn (PB05E) Larry E Nicholson (ON03RC) R.K. Rhyne (EC07J) R. Branch (MG01MM)

pages 140

FORM NIS-1 OWNER'S DATA REPORT-FOR INSERVICE INSPECTIONS

As required by the Provisions of the ASME Code Rules

1. Owner:Duke Energy Corporation, 526 S. Church St., Charlotte, NC 28201-1006

(Name and Address of Owner)

2 Plant: McGuire Nuclear Station. Highway 73 Cowans Ford. N.C. 28216

3

5.

(Name and Address of Plant)

Plant Unit: 2 4. Owner Certificate of Authorization (if required) N/A

Commercial Service Date: March 1.1984 .6. National Board Number for Unit -4:

7. Components Inspected:

Component or Appurtenance

Manufacturer or Manufacturer or State or Installer Installer Serial. Province No.

No.

See Section 1.1 in the Attached Report

Note: Supplemental sheets in form of lists, sketches, or drawings may be used provided (1) size is 8'112fTi- x.

11 in., (2) information in items 1 through 6 on this data report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

National Board No..

FORM NIS-1 (Back)

8. Examination Dates April 16, 1999 to October 13, 2000

9. Inspection Period Identification:

10. Inspection Interval Identification:

11. Applicable Edition of Section XI

12. Date/Revision of Inspection Plan:

Second Period

Second Interval

1989 Addenda None

September 7, 1999/Revision 3

13. Abstract of Examinations and Test. Include a list of examinations and tests and a statement concerning status of work required for the Inspection Plan. See Sections 3.0. 4.0 and 11.0

14. Abstract of Results of Examination and Tests.

15. Abstract of Corrective Measures.

See Section 5.0 and 11.0

See Section 8.0

We certify that a) the statements made in this report are correct b) the examinations and tests meet the Inspection Plan as required by the ASME Code, Section XI, and c) corrective measures taken conform to the rules of the ASME Code, Section XI.

Certificate of Authorization No. (if applicable)

Date -•2e: J Signed Duke Enera\Owner

N/A Expiration Date

vo Cor. By X 1, LP

CERTIFICATE OF INSERVICE INSPECTION

I, the undersigned, holding a valid commisnion issued by the National Board of Boiler and Pressure Vessel Inspectors and the State of Province of "6L"-r'4 .- .hL(&JA employed by * The HSBI&I Co. of HI -r- . cr have inspected the components described in this Owners' Report during the

period i.. $... . to 0-•"90 , and state that to the best of my knowledge and belief, the Owner has performed examinations and tests and taken corrective measures described in the Owners' Report in accordance with the Inspection Plan and as required by the ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations, test, and corrective measures described in this Owners' Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection

___Commissions I'J 77(i3, to./ A) -2Inspect Is Signature

Date /&Ii

National Board, State, Province, and -naorsements

* The Hartford Steam Boiler Inspection & Insurance Co. 200 Ashford Center North Suite 300 Atlanta, GA. 30338

N/A

L

Ili I I I 0>

INSERVICE INSPECTION REPORT UNIT 2 MCGUIRE 2000

OUTAGE 5/EOC-13

Location: Hwy. 73, Cowans Ford, North Carolina 28216

NRC Docket No. 50-370

National Board No. 84

Commercial Service Date: March 1, 1984

Owner: Duke Energy Corporation 526 South Church St.

Charlotte, N.C. 28201-1006

Revision 0

Prepared By:

Reviewed By:

Approved By:

Date \ Z. I |zo0

Date /12 1q Zoo

Date jz 1 6-

DISTRIBUTION LIST

Duke Energy Corporation Quality Assurance Technical Services (Original Copy

McGuire Mechanical Maintenance/ QA Technical Support

NRC Document Control

Hartford Steam Boiler Inspection and Insurance Company (AIA); ANII/McGuire

State of North Carolina Department of Labor c/o J. M. Givens, Jr.

Nuclear GO Regulatory & Industrial Affairs c/o Laura Burba Mail Code/ EC050

TABLE OF CONTENTS

Section Title Revision

1. General Information 0

2. Summary of Inservice Inspections 0

3. Second Ten Year Inspection Status 0

4. Final Inservice Inspection Plan 0

5. Results of Inspections Performed 0

6. Reportable Indications 0

7. Personnel, Equipment, and Material Certifications 0

8. Corrective Action 0

9. Reference Documents 0

10. Class 1 (Tab A) and 2(Tab B) Repairs and Replacements 0

11. Pressure Testing 0

1.0 General Information

This report describes the Inservice Inspection of Duke Energy Corporation's McGuire Nuclear Station Unit 2 during Outage 5/EOC-13. This is the Third Outage of the Second Inspection Period of the Second Ten Year Interval.

Included in this report are the final Inservice Inspection Plan, the inspection results for each item, a summary for each category of examination and corrective action taken when unacceptable conditions were found. In addition, there is a section included for repairs and replacements required since April 16, 1999.

1.1 Identification Numbers

Manufacturer National Manufacturer or Installer State or Board

Item or Installer Serial No. Province No. No.

Reactor Vessel Rotterdam 30664 NC-201819 -

Pressurizer Westinghouse 1491 NC-201818 W1 0285

Steam Generator 2A BWI 7700-02 NC-302674 159

Steam Generator 2B BWI 7700-04 NC-302675 161

Steam Generator 2C BWI 7700-01 NC-302676 158

Steam Generator 2D BWI 7700-03 NC-302677 160

Centrifugal Pacific Pumps 2A - 48584 N/A 25 Charging Pump 2B1- 48585 28

Containment Spray Heat Delta Southern Co. 2A-35005-73-3 NC-234203 3396 Exchanger 2B-35005-73-4 NC-201822 3397

Outage 5/EOC-13 McGuire Unit 2 Section 1

Page 1 of 4 Revision 0 December 6, 2000

Identification NumbersContinued



Manufacturer National Manufacturer or Installer State or Board

Item or Installer Serial No. Province No. No.

Excess Letdown Heat Westinghouse 1810 NC-234264 1555 Exchanger

Letdown Heat Exchanger Joseph Oat & Sons, Inc. 2049-2B NC-201842 553

Reciprocating Charging Union Pump Co. N721031 B-604 N/A 80 Pump

2A 5-114E841G02 Reactor Coolant Pump Westinghouse 2B 6-114E841 G02 N/A N/A

2C 7-114E841G02 2D 8-114E841G02

Reciprocating Charging Metal Bellows Company 74730-002 N/A 002 Pump Accumulator

Reciprocating Charging Richmond Engineering N-2409.20 N/A 75220 Pump Suction Stabilizer Supply Co.

Residual Heat Joseph Oat & Sons, Inc. 2A 2046-2C NC-169800 637 Removal Heat 2B 2046-2D NC-201823 638 Exchanger

Safety Injection Pump Pacific Pumps 2A 49357 N/A 130 2B 49358 131

Regenerative Heat Joseph Oat & Sons, Inc. 2047-2B NC-201817 628 Exchanger 629

630

Seal Water Heat Atlas Industrial 1767 NC 201827 1549 Exchanger Manufacturing Company

Seal Water AMF Cuno 2A -20 N/A 4364 Injection Filter 2B - 22 4365

1.1

1.1 Identification NumbersContinued

Manutacturer Manufacturer or Installer State or National

Item or Installer Serial No. Province No. Board No.

Main Steam Supply to Duke Power Co. SA N/A 62 Auxiliary Equipment System

Containment Air Duke Power Co. VQ N/A 56 Release and Addition System

Main Steam System Duke Power Co. SM NIA 70

Main Steam Vent to Duke Power Co. SV N/A 67 Atmosphere System_

Reactor Coolant Duke Power Co. NC N/A 82 System

Liquid Waste Recycle Duke Power Co. WL N/A 76 System

Refueling Water Duke Power Co. FW N/A 54 System

Auxiliary Feedwater Duke Power Co. CA N/A 73 System

Residual Heat Duke Power Co. ND N/A 63 Removal System

Nuclear Service Water Duke Power Co. RN N/A 60 System

Chemical & Volume Duke Power Co. NV N/A 80 Control System

Component Cooling Duke Power Co. KC N/A 78 System

Main Feedwater Duke Power Co. CF N/A 61 System

Containment Spray Duke Power Co. NS N/A 69 System IIIII



1.1 Identification Numbers Continued

Manufacturer Manufacturer or Installer State or National

Item or Installer Serial No. Province No. Board No.

Containment Duke Power Co. RV N/A 72 Ventilation Cooling Water System

Safety Injection System Duke Power Co. NI N/A 83

Unit 2 Duke Power Co. N/A N/A 84

1.2 Authorized Nuclear Inservice Inspector(s)

Name: R. D. Klein

Employer: The Hartford Steam Boiler Inspection & Insurance Company

Business The Hartford Steam Boiler Inspection & Insurance Co.

Address: 200 Ashford Center North Suite 300 Atlanta, GA 30338



2.0 Summary of Inservice Inspections

The information shown below provides an abstract of ASME Section XI Class 1, Class 2, and Augmented Items scheduled and examined during Outage 5/EOC-1 3 at McGuire Nuclear Station Unit 2.

2.1 Class 1 Inspection

Examination Category B-A Pressure Retaining Welds in Reactor Vessel

item Description Total Examined

Number During Outage

B01.010 Shell Welds

B01.011 Circumferential 0

B01.012 Longitudinal N/A

B01.020 Head Welds


B01.022

B01.030

B01.040

B01.050

B01.051

TOTALS

Meridional

Shell-to-Flange Welds

Head-to-Flange Welds

Repair Welds

0

0

0

Beltline Region N/A

0



I -

Exami



nation Category B-B Pressure Retaining Welds in Vessels Other than Reactor Vessels

Item Description Total Examined


Pressurize B02.01 0 Shell-to-Head Welds


B02.012 Longitudinal

B02.020 Head Welds

B02.021 Circumferential N/A

B02.022 Meridional N/A

(Primary Side)

B02.030 Head Welds



B02.040 Tubesheet-to-Head Weld 0

Heat Exchangers (Primary Side) -- Head

B02.050 Head Welds



Heat Exchangers ' ~~(primary Side) -- Shell ...

B02.060 Tubesheet-to-Head Welds N/A

B02.070 Longitudinal Welds N/A

B02.080 Tubesheet-to-Shell Welds N/A

TOTALS 0

Examination Category B-D Full Penetration Welds of Nozzles in Vessels Inspection Program B

item Description Total Examined0 ....Number , During Outage

PReactor Vessel

B03.090 Nozzle-to-Vessel Welds 0

B03.100 Nozzle Inside Radius Section 0 S.......... .. Pressurizer . .

B03.1 10 Nozzle-to-Vessel Welds 0

B03.120 Nozzle Inside Radius Section 0

S.. )_. Steam Generators (Primary Side)

B03.130 Nozzle-to-Vessel Welds N/A

B03.140 Nozzle Inside Radius Section 0

B03.150 Nozzle-to-Vessel Welds N/A

B03.160 Nozzle Inside Radius Section N/A

TOTALS 0

Examination Category B-E Pressure Retaining Partial Penetration Welds in Vessels

REFERENCE SECTION 11.0 OF THIS REPORT



Examination Category B-F Pressure Retaining Dissimilar Metal Welds

Item Description Total Examined Number During Outage

Reactor Vessel

B05.010 Nominal Pipe Size 4" or Larger 0 Nozzle-to-Safe End Butt Welds

B05.020 Nominal Pipe Size Less Than 4" N/A Nozzle-to-Safe End Butt Welds

B05.030 Nozzle-to-Safe End Socket Welds N/A

Pressurizer




Steam Generator




Heat Exchangers

B05.100 Nominal Pipe Size 4" or Larger N/A Nozzle-to-Safe End Butt Welds


605.120 Nozzle-to-Safe End Socket Welds N/A

Outage 5/EOC-13 Page 4 of 19

McGuire Unit 2 Revision 0

Section 2 December 6, 2000

Examination Category B-F

Piping

B05.130 Nominal Pipe Size 4" or Larger Dissimilar Metal Butt Welds

0

B05.140 Nominal Pipe Size Less Than 4" N/A Dissimilar Metal Butt Welds

B05.150 Dissimilar Metal Socket Welds N/A

TOTALS 1 0

Examination Category B-G-1 Pressure Retaining Bolting, Greater Than 2" in Diameter


Reactor Vessel

B06.010 Closure Head Nuts 0

B06.020 Closure Studs (in place) 0

B06.030 Closure Studs (when removed) 0

B06.040 Threads in Flange 0

B06.050 Closure Washers, Bushings 0

Pressurizer

B06.060 Bolts and Studs N/A

B06.070 Flange Surface (when connection N/A disassembled)

B06.080 Nuts, Bushings, and Washers N/A

S~Steam Generators

B06.090 Bolts and Studs 0

B06.100 Flange Surface (when connection *8 disassembled)

B06.110 Nuts, Bushings, and Washers 0



(Continued)

Examination Category B-G-1

Heat Exchangers

B06.120 N/A



• • Piping




Pumps

B06.180 Bolts and Studs 0

B06.190 Flange Surface1 0 (when connection disassembled)


Valves


B06.220 Flange Surface1 N/A (when connection disassembled)


TOTALS *8

Items disassembled will be examined but will not be counted in the totals or percentages for the B-G-1 category. These items will be listed in sections 4 and 5 of the applicable report.

* These items were examined but will not be counted in the totals. Examinations performed during

the third period will be credited for report totals.



Bolts and Studs

(Continued)

Examination Category B-G-2 Pressure Retaining Bolting, 2" and Less in Diameter

Item Numbc

Description Total Examined Durina Outaae

Reactor Vessel

B07.010 Bolts, Studs, and Nuts

* A.Pressurizer


Steam Generators


Heat Exchangers


Piping


SPumps


CValvesing

B07.070 Bolts, Studs, and Nuts CRD Housing

B07.080 Bolts, Studs, and Nuts in CRD

Housing when disassembled 2

TOTALS

N/A

n

N

0 1

N

0

1

2 Items disassembled will be examined but will not be counted in the totals or percentages for the B-G-2

category. These items will be listed in sections 4 and 5 of the applicable report.



I

Integral Attachments for VesselsExamination Category B-H

Total Examined Irfrinn OItari

Reactor Vessel

Integrally Welded Attachments 0

Pressurizer

I Integrally Welded Attachments 0

Steam Generators

RnR n(0 IIntegrally Welded Attachments

Heat Exchangers

B08.040 Integrally Welded Attachments N/A

TOTALS 0

Examination Category B-J Pressure Retaining Welds in Piping



B09.010 Nominal Pipe Size 4" or Larger

B09.011 Circumferential Welds 15

B09.012 Longitudinal Welds 3 N/A

B09.020 Nominal Pipe Size Less than 4"

B09.021 Circumferential Welds 0

B09.022 Longitudinal Welds 3 N/A



Item Number

N/A

DescriptionI

I

I

Examination Category B-J

B09.030

R0g.031

Branch Pipe Connection Welds

Nominal Pipe Size 4" or Larger 0

B09.032 Less than Nominal Pipe Size 4" 0

B09.040 Socket Welds 10

TOTALS 25

3 Longitudinal welds in Examination Category B-J that intersect circumferential welds are examined per Code Case N-524.

Examination Category B-K-1

Item

B10.010

Description

Piping

Inte-qrally Welded Attachments

Pumps

Integrally Welded Attachments

Valves

B 10.030 Integrally Welded Attachments N/A

TOTALS N/A



Integral Attachments for Piping,

Pumps and Valves

Total Examined nrr}•nen i tiH rv I

N/A

(Continued)

I

I

Examination Category B-L-l, B-M-1

B-L-2, B-M-2

Item Number

Pressure Retaining Welds in Pump Casings and Valve Bodies

Pump Casings and Valve Bodies

Description

Pumps

Total Examined f -l " nfrmý IwAz~~

Pump Casing Welds (B-L-l)

Pump Casing (B-L-2) (when disassembled for Maintenance Repair or Volumetric Examination)

N/A

0

Valves

B12.030 Valves, Nominal Pipe Size Less than 4" Valve Body Welds (B-M-1)

N/A

B12.040 Valves, Nominal Pipe Size 4" or N/A Larger Valve Body Welds (B-M-l)

B12.050 Valve Body, Exceeding 4" Nominal 0 Pipe Size (B-M-2)

TOTALS 0

Examination Category B-N-1 Interior of Reactor Vessel

B-N-2 Integrally Welded Core Support Structures and Interior Attachments to Reactor Vessels

B-N-3 Removable Core Support Structures


Reactor Vessel

B13.010 Vessel Interior (B-N-1) 0



I

Examination Category B-N-l, B-N-2, B-N-3 (Continued)

Reactor Vessel (PWR)

B13.050 Interior Attachments Within the Beitline Regcion (B-N-2)

N/A

B13.060 Interior Attachments Beyond Beltline 0 Region (B-N-2)

B13.070 Core Support Structure (B-N-3) 0

TOTALS 1 0

Examination Category B-O Pressure Retaining Welds in Control Rod Housings



Reactor Vessel

B14.010 Welds in CRD Housing 0

TOTALS 0

Examination Category B-P All Pressure Retaining Components




Examination Category B-Q

Note: Steam Generator Tubing is examined and documented by the Steam Generator Maintenance Group of the Station Support Division as required by the Station Technical Specifications and is not included in this report.

Examination Category F-A Class I Component Supports

Outage 5/EOC-13 McGuire Unit 2

Section 2



F01.010 Class 1 Piping Supports (Code Case 2 N-491 applies) Reference Section 4.0 of this report

TOTALS 1 2

Steam Generator Tubing

2.2 Class 2 Inspections

Examination Category C-A Pressure Retaining Welds in Pressure Vessels


C011.010 Shell Circumferential Welds 0

C01.020 Head Circumferential Welds 0

C01.030 Tubesheet-to-Shell Weld 2

TOTALS 2

Examination Category C-B Pressure Retaining Nozzle Welds in Vessels


C02.010 Nozzles in Vessels < 1/2" Nominal Thickness I

C02.011 Nozzle-to-Shell (or Head) Weld 0

C02.020 Nozzles Without Reinforcing Plate in Vessels >1/2" Nominal Thickness

C02.021 Nozzle-to-Shell (or Head) Weld 1

C02.022 Nozzle Inside Radius Section ' 0


Page 13 of 19 Revision 0

December 6, 2000

Examination Category C-B

C02.030

C02.031

(Continued)

Nozzles With Reinforcing Plate in Vessels >1/2" Nominal Thickness

Reinforcing Plate Welds to Nozzle and Vessel

0

C02.032 Nozzle-to-Shell (or Head) Welds N/A when Inside of Vessel is Accessible

C02.033 Nozzle-to-Shell (or Head) Welds 0

when Inside of Vessel is Inaccessible 1 _1

TOTALS _________________________________1

4 (Item # C02.022) Nozzle Inside Radius Section welds are examined as required by Table IWC2500-1 Category C-B. However, for reporting purposes, the totals do not reflect the number of Nozzle Inside Radius Section welds examined during this outage. Nozzle Inside Radius Section welds are to be examined in conjunction with C02.021. examinations.

Examination Category C-C Integral Attachments for Vessels, Piping, Pumps, and Valves

Description

Pressure Vessels

Total Examined nrfflrnrir"r Ia•i nif

I Integral Welded Attachments

Piping


Pumps


Valves

C03.040 Integrally Welded Attachments N/A

TOTALS 1



Item umber

N

I

N

I

II .N N-winn

Examination Category C-D

Item ,.njhnI

Pressure Retaining Bolting Greater Than 2" in Diameter

Description Total Examined frnrinn Mifmtnaf

Pressure Vessels

C04.01 0 Bolts and Studs

Piping

C04.020 I Bolts and Studs

Pumps

Bolts and Studs

Valves

C04.040 Bolts and Studs N/A

TOTALS N/A

Examination Category C-F-1 Pressure Retaining Welds in Austenitic Stainless Steel or High Alloy Piping


C05.010 Piping Welds > 3/8" Nominal Wall Thickness for Piping > Nominal Pipe Size 4"

C05.011 Circumferential Weld 12

C05.012 Longitudinal Weld5 See Code Case N-524



N/A

I

I

Examination Category C-F-1

C05.020

C05.021

Piping Welds > 1/5" Nominal Wall Thickness for Piping _> Nominal Pipe Size 2" and < Nominal Pipe Size 4"

Circumferential Weld 8

C05.022 Longitudinal Weld' N/A

C05.030 Socket Welds 5

C05.040 Pipe Branch Connections of Branch Piping > Nominal Pipe Size 2"


C05.042 Longitudinal Weld5 N/A

TOTALS 25

5Longitudinal welds in Examination Categories C-F-1 and C-F-2 that intersect circumferential welds are examined per Code Case N-524.

Examination Category C-F-2 Pressure Retaining Welds in Carbon or Low Alloy Steel Piping


C05.050 Piping Welds _> 3/8" Nominal Wall Thickness for Piping > Nominal Pipe Size 4"


C05.052 Longitudinal Weld5 See Code Case N-524



(Continued)

Examination Category C-F-2

C05.060

f'lO( ORI(R

Piping Welds > 1/5" Nominal Wall Thickness for Piping > Nominal Pipe Size 2" and <_ Nominal Pipe Size 4"

Circumferential Weld N/A


C05.070 Socket Welds N/A

C05.080 Pipe Branch Connections of Branch Piping > Nominal Pipe Size 2"

C05.081 Circumferential Weld N/A


TOTALS 11

5Longitudinal welds in Examination Categories C-F-1 and C-F-2 that intersect circumferential welds

are examined per Code Case N-524.

Examination Category C-G Pressure Retaining Welds in Pumps and Valves


Pumps

C06.010 Pump Casing Welds N/A

Valves

C06.020 Valve Body Welds 0

TOTALS 0

Examination Category C-H All Pressure Retaining Components


Outage 5fEOC-13 McGuire Unit 2 Section 2


(Continued)

Class 2 Component Supports


F01.020 Class 2 Piping Supports (Code Case 10 N-491 applies) Reference Section 4.0 of this report

TOTALS _ 10

Examination Category F-A Supports Other than Piping Supports


F01.040 Supports other than Piping Supports 2 Class 1, 2, & 3 (Code Case N-491 applies) Reference Section 4.0 of this report

TOTALS 2

Examination Category Component Supports Class 1, 2, & 3


F01.050 Component supports snubbers Class * N/A •1,2& 3

TOTALS * N/A

• Examinations to be performed per Request for Relief 97-005



Examination Category F-A

2.3 Augmented Inspection

Item Total Examined Number Description During Outage

G01.001 RCP Flywheel Exam 0

G03.001 Pipe Rupture Protection 0

TOTALS 0



3.0 Second Ten Year Interval Inspection Status

The completion status of inspections required by the 1989 ASME Code Section XI, no Addenda is summarized in this section. The requirements are listed by the ASME Section Xl Examination Category as defined in Table IWB-2500-1 for Class 1 Inspections, Table IWC-2500-1 for Class 2 Inspections, and IWF-25001(Code Case N-491 applies) for Class 1, 2 and 3 Component Supports. Augmented inspections are also included.

Class I Inspections

Examination Description Inspections Inspections Percentage 6Deferral Category Required Completed Completed Allowed

B-A Pressure Retaining Welds 15 3 20.00% Yes in Reactor Vessel

B-B Pressure Retaining Welds 5 3 60.00% No in Vessels Other than Reactor Vessels

B-D Full Penetration Welds of 36 22 61.11% Partial Nozzles in Vessels Inspection Program B

B-E Pressure Retaining Partial Penetration Welds in Vessels REFERENCE SECTION 11.0 OF THIS REPORT

B-F Pressure Retaining 38 24 63.15% No Dissimilar Metal Welds

B-G-1 Pressure Retaining Bolting 241 159 65.97% No Greater than 2" in Diameter

B-G-2 Pressure Retaining Bolting 22 14 63.63% No 2" and Less in Diameter I j



Class I Inspections (Continued)

Examination Description Inspections Inspections Percentage 6Deferral Category Required Completed Completed Allowed

B-H Integral Attachments for 12 7 58.33% No Vessels

B-J Pressure Retaining Welds 197 125 63.45% No in Piping

B-K-1 Integral Attachments for N/A N/A N/A No Piping, Pumps and Valves

B-L-1 Pressure Retaining Welds N/A N/A N/A Yes in Pump Casings

B-L-2 Pump Casings 1 0 00.00% Yes

B-M-1 Pressure Retaining N/A N/A N/A Yes Welds in Valve Bodies

B-M-2 Valve Body > 4 in. 6 3 50.00% Yes Nominal Pipe Size

B-N-1 Interior of Reactor Vessel 3 2 66.66% No

B-N-2 Integrally Welded Core Support Structures and 2 0 00.00% Yes Interior Attachments to Reactor Vessels

B-N-3 Removable Core Support 1 0 00.00% Yes Structures

B-O Pressure Retaining Welds 3 2 66.66% Yes in Control Rod Housings



Class I Inspections (Continued)

Examination Description Inspections Inspections Percentage 6Deferral

Category Required Completed Completed Allowed

B-P Al Pressure Retaining REFERENCE SECTION 11.0 OF THIS REPORT Components

B-Q Steam Generator Tubing See Note below

F-A Class I Component 49 32 65.30% No F01.010 Supports

(Code Case N-491) I

Note: Steam Generator Tubing is examined and documented by the Steam Generator Maintenance Group of the Station Support Division as required by the Station Technical Specifications and is

not included in this report.

6 Deferral of inspection to the end of the interval as allowed by ASME Section XI Tables IWB and IWC

2500-1



Class 2 Inspections



C-A Pressure Retaining Welds 25 16 64.00% No

in Pressure Vessels

C-B Pressure Retaining Nozzle 22 12 54.54% No

Welds in Vessels

C-C Integral Attachments for 9 5 55.55% No

Vessels, Piping, Pumps, and Valves

C-D Pressure Retaining Bolting N/A N/A N/A No

Greater Than 2" in Diameter

C-F-1 Pressure Retaining Welds 251 160 63.74% No

in Austenitic Stainless Steel or High Alloy Piping

C-F-2 Pressure Retaining Welds 51 31 60.78% No

in Carbon or Low Alloy Steel Piping

C-G

C-H

F-A

F01.020

Pressure Retaining Welds in Pumps and Valves

All Pressure Retaining Components

Class 2 Component Supports (Code Case N-491)

6 Deferral of inspection to the end of the 2500-1

6 4 66.66%

-J ______________________ a ______________________ .1 ____________________


-1. I

i , --

181 11664.08% No

interval as allowed by ASME Section Xl Tables IWB and IWC



No

Additional Component Support Examinations Class 1, 2 & 3



F-A Supports other than Piping 36 22 61.11% No

F01.040 Supports Class 1, 2 & 3 (Code Case N-491applies)

Examination Description Inspections Inspections Percentage 6DeferTal


F-A Component Supports No

F01.050 Snubbers Class 1, 2 & 3

6 Deferral of inspection to the end of the interval as allowed by ASME Section X1 Tables IWB-2500-1 and

IWC-2500-1.

*Examinations to be performed per Request for Relief 97-005

Augmented Inspections

Description Percentage Complete

Reactor Coolant Pump Flywheels (Item No. Series GO1.) 100% of requirements for OUTAGE 5/EOC-13

Pipe Rupture Protection (Item No. Series G03.) 100% of requirements for OUTAGE 5/EOC-13



4.0 Final Inservice Inspection Plan

The final ISl Plan shown in this section lists all ASME Section Xl Class 1 and Class 2, and Augmented examinations credited for Outage 5/EOC-13 at McGuire Nuclear Station Unit 2.

The information shown below is a field description for the reporting format included in this section of the report:

Item Number

ID Number

Iso / Dwg. Numbers

Proc

Insp Req.

Mat / Sch.

Diam. / Thick

Cal Blocks

Comments

= ASME Section Xl Tables IWB-2500-1 (Class 1), IWC-2500-1 (Class 2), IWF-2500-1 (Class 1 and Class 2 ), Augmented Requirements

= Unique Identification Number

= Location and/or Detail Drawings

- Examination Procedures

= Examination Technique - Magnetic Particle, Dye Penetrant, etc.

= General Description of Material

= Diameter/Thickness

= Calibration Block Number

= General and/or Detail Description

Outage 5fEOC-13 McGuire Unit 2 Section 4


EOC 13

CATEGORY B-G-1, Pressure Retaining Bolting, Greater than 2" In Diameter

tearn Generators

ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS

**** Flange Surface, when connection dissassembled ****

DUKE ENERGY CORPORATION QUALITY ASSURANCE TECHNICAL SERVICES

Inservice Inspection Database Management System

McGuire 2

Inservice Inspection Plan for Interval 2 Outage 5 PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS

B06.100.001 2SGA-MW-YI-Xl NC MCM 2201.01-0194 QAL-13 VT-1 CS 0.000 2A SIG PRIMARY INLET MANWAY FLANGE.

MCM 2201.01-0126 0.000 YI-X1 QUADRANT. REFERENCE 2MNS-065

Class A

B06.100.002 2SGA-MW-X1-Y2 NC MCM 2201.01-0194 QAL-13 VT-I CS 0.000 2A SIG PRIMARY OUTLET MANWAY FLANGE.

MCM 2201.01-0126 0.000 X1-Y2 QUADRANT. REFERENCE 2MNS-065

Class A

806.100.003 2SGB-MW-YI-X2 NC MCM 2201.01-0194 QAL-13 VT-1 CS 0.000 2B SIG PRIMARY INLET MANWAY FLANGE.

MCM 2201.01-0127 0.000 Y1-X2 QUADRANT. REFERENCE 2MNS-065

Class A

B06.100.004 2SGB-MW-X2-Y2 NC MCM 2201.01-0194 QAL-13 VT-I CS 0.000 2B S/G PRIMARY OUTLET MANWAY FLANGE.

MCM 2201.01-0127 0.000 X2-Y2 QUADRANT. REFERENCE 2MNS-065

Class A

B06.100.005 2SGC-MW-Y1-X1 NC MCM 2201.01-0194 QAL-13 VT-1 CS 0.000 2C S/G PRIMARY INLET MANWAY FLANGE.

MCM 2201.01-0126 0.000 Y1-X1 QUADRANT. REFERENCE 2MNS-065

Class A

806.100.006 2SGC-MW-X1-Y2 NC MCM 2201.01-0194 QAL-13 VT-1 CS 0.000 2C S/G PRIMARY OUTLET MANWAY FLANGE.

MCM 2201.01-0126 0.000 Xl-Y2 QUADRANT. REFERENCE 2MNS-065

Class A

B06.100.007 2SGD-MW-Y1-X2 NC MCM 2201.01-0194 QAL-13 VT-1 CS 0.000 2D S/G PRIMARY INLET MANWAY FLANGE.

MCM 2201.01-0127 0.000 YI-X2 QUADRANT. REFERENCE 2MNS-065

Class A

B06.100.008 2SGD-MW-X2-Y2 NC MCM 2201.01-0194 QAL-13 VT-1 CS 0.000 2D S/G PRIMARY OUTLET MANWAY FLANGE.

MCM 2201.01-0127Class A

Total B06.100 Items:

Total B06 Items:

0.000 X2-Y2 QUADRANT. REFERENCE 2MNS-065

8 8

Plan Report Page 1

1210612000

COMMENTS

EOC 13

CATEGORY B-G-2, Pressure Retaining Bolting, 2" And Less In Diameter




McGuire 2

Inservice Inspection Plan for Interval 2 Outage 5 PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

Plan Report Page 2

1210612000

**** Bolts, Studs, and Nuts **** B07.070.003B 2NC-34A NC MCFI-2NC62 QAL-13 VT-1 SS 0.000 3" VALVE. INSPECT ONLY ONE VALVE IN THIS

MC 2553-2.0 0.000 GROUP PER INTERVAL

Class A MCM 1205.09-08

Total B07.070 Items: 1

Total B07 Items: I

EOC 13

CATEGORY B-J, Pressure Retaining Welds In Piping MNPS 4 or Larger

ITEM NUMBER ID NUMBER SYS ISOIDWG NUMBERS



McGuire 2


**** Circumferential Welds ****

B09.011.010 2NC2FW2-3 NC MCFI-2NC2 NDE-600 UT SS 14.000 50207 PRESSURIZER SURGE LINE SE Circumferential MCM 2201.01-118 160 1.406 UT FROM PIPE SIDE

Class A Term end Pipe to SAFE END

B09.011.010A 2NC2FW2-3 NC MCFI-2NC2 NDE-35 PT SS 14.000 PRESSURIZER SURGE LINE SE Circumferential MCM 2201.01-118 160 1.406

Class A Term end Pipe to SAFE END

B09.011.010B 2NC2FW2-3 NC MCFI-2NC2 NDE-600 UT SS 14.000 50207 PRESSURIZER SURGE LINE SE

Circumferential MCM 2201.01-118 1.640 UT FROM SE SIDE

Class A Term end SAFE END to Pipe SAFE END

B09.011.031 2NC2FW53-24 NC MCFI-2NC53 NDE-600 UT SS 6.000 50211 Circumferential 160 0.719

Class A Stress weld Pipe to Elbow

B09.011.031A 2NC2FW53-24 NC MCFI-2NC53 NDE-35 PT SS 6.000 Circumferential 160 0.719



Class A Stress weld Elbow to Flange



B09.01 1.034 2NC2FW53-28 NC MCFI-2NC53 NDE-600 UT SS 6.000 50211160Circumferential

Class A Stress weld0.719

Pipe to Elbow

Plan Report Page 3

1210612000

EOC 13

CATEGORY B-J, Pressure Retaining Welds In Piping



McGuire 2

Inservice Inspection Plan for Interval 2 Outage 5

ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

B09.011.034A 2NC2FW53-28 NC MCFI-2NC53 NDE-35 PT SS 6.000

Circumferential 160 0.719


B09.011.035 2NC2FW53-29 NC MCFI-2NC53 NDE-600 UT SS 6.000 50211


Class A Stress weld Elbow to Pipe








Circumferential 160 0.719 Class A Stress weld Elbow to

Pipe





B09.011.038A 2NC2FW53-36 NC MCFI-2NC53 NDE-35 PT SS 6.000160Circumferential

Class A Stress weld

0.719

Pipe to Elbow

Plan Report Page 4

1210612000

EOC 13

CATEGORY B-J, Pressure Retaining Welds In Piping

MNP 4 or Langer



McGuire 2


Circumferential Class A

160 Valve 2N1181 to Elbow

0.719

Plan Report Page 5

12/0612000





B09.011.039A 2NC2FW53-37 NC MCFI-2NC53 NDE-35 PT SS 6.000



B09.011.162 2N12F471 NI MCFI-2NI15 NDE-600 UT SS 6.000 50211


Class A Valve 2N1180 to Elbow

B09.011.162A 2NI2F471 NI MCFI-2NI15 NDE-35 PT SS 6.000


Class A Valve 2N1180 to Elbow



Class A Pipe to Elbow










B09.011.165 2NI2F494 NI MCFI-2NI16 NDE-600 UT SS 6.000 50211

EOC 13

CATEGORY B-J. Pressure Retaining Welds In PipingP MN 4 r Larger



McGuire 2



B09.011.165A 2N12F494 NI MCFI-2NI16 NDE-35 PT SS 6.000


Class A Valve 2NI181 to Elbow

B09.011.166 2NI2F496 NI MCFI-2NI16 NDE-600 UT SS 6.000 50211


Class A Elbow to Pipe

B09.011.166A 2Nl2F496 NI MCFI-2NI16 NDE-35 PT SS 6.000


Class A Elbow to Pipe

B09.011.167 2Nl2F866 NI MCFI-2NI16 NDE-600 UT SS 6.000 50211



B09.011.167A 2N12F866 NI MCFI-2NI16 NDE-35 PT SS 6.000



Total B09.011 Items: 31

Plan Report Page 6

12/06/2000

EOC 13

CATEGORY B-J, Pressure Retaining Welds In

Piping 2ocket Welds




McGuire 2

Inservice Inspection Plan for Interval 2 Outage 5PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

B09.040.006 2NC2FW40-1 NC MCFI-2NC40 NDE-35 PT SS 2.000

Socket 160 0.344

Class A Stress weld Nozzle to Pipe


Socket 160 0.281

Class A Stress weld Full Coupling to Pipe


Socket 160 0.281

Class A Stress weld Valve 2N117 to Pipe

B09.040.050 2NI2FW89-1 NI MCFI-2N189 NDE-35 PT SS 1.500

Socket 160 0.281

Class A Stress weld Valve 2NI349 to Pipe

B09.040.051 2NI2FW89-3 NI MCFI-2NI89 NDE-35 PT SS 1.500

Socket 160 0.281



Socket 160 0,281

Class A Stress weld Pipe to Valve 2NI19

B09,040.053 2NI2FW89-5 NI MCFI-2NI89 NDE-35 PT SS 1.500

Socket 160 0.281



Socket

Class A Stress weld

160 Pipe to Valve 2NI15

0.281

Plan Report Page 7

12106/2000

r

EOC 13

CATEGORY B-J, Pressure Retaining Welds In Piping e

f2ockt Welds



McGuire 2


ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMEN I


Socket 160 0.281



Socket 160 0.281

Class A Stress weld Pipe to Valve 2NI17

Total B09.040 Items:

Total B09 Items:

10 41

Plan Report Page 8

12106/2000

EOC 13

CATEGORY C-A! Pressure Retaining Welds In Pressure Vessels Eiubesheet-to-Shell Weld




McGuire 2

Inservice Inspection Plan for Interval 2 Outage 5 PROC INSP REQ MAT/SCH DIANTHK CAL BLOCKS COMMENTS

Plan Report Page 9

12/0612000

C01.030.011 2BCSHX-50-B NS MCM 1201.06-0093 NDE-630 UT SS 55.375 50420 2B CONTAINMENT SPRAY HEAT EXCH. SHELL Circumferential MC 2563.1-0 0.437 TO BOTTOM TUBE SHEET PSI EXAMINATION

Class B SHELL(2B) to LISTED ID# AS NS COOLER 2B-120

TUBESHEET

C01.030.012 2BCSHX-50-A NS MCM 1201.06-0093 NDE-630 UT SS 55.375 50420 2B CONTAINMENT SPRAY HEAT EXCH. SHELL

Circumferential MC 2563.1-0 0.437 TO TOP TUBE SHEET PSI EXAMINATION LISTED

Class B SHELL(2B) to ID# AS NS COOLER 2B3-125

TUBESHEET

Total C01.030 Items: 2Total C01 Items: 2

EOC 13

CATEGORY C-B, Pressure Retaining Nozzle Welds In Vessels

Nzz._les Without Reinforcing Plate In Vessels > W112 in. Nom. ThicknessITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS



McGuire 2

Inservice Inspection Plan for Interval 2 Outage 5 PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS

**** Nozzle-to-Shell (or Head) Weld **** C02.021.007 2SGC-W259 SM M

Circumferential M Class B

1CM 2201.01-0207

1CM 2201.01-0160

NDE-620 UT CS

See Com Nozzle to SHELL

6.000 5139385 STEAM GENERATOR 2C AUXILLIARY

4.125 50236A FEEDWATER NOZZLE TO SHELL. REFERENCE 2MNS-068 ADDED AS A RESULT OF S/G REPLACEMENT. Depending upon the examiner's qualifications, procedure PDI-UT-6 may be used in lieu of procedure NDE-620

C02.021.007A 2SGC-W259

Circumferential Class B

SM MCM 2201.01-0207

MCM 2201.01-0160NDE-25 MT CS 6.000

4.125

Nozzle to SHELL

STEAM GENERATOR 2C AUXILLIARY FEEDWATER NOZZLE TO SHELL. REFERENCE 2MNS-068 ADDED AS A RESULT OF S/G REPLACEMENT.

Total C02.021 Items: 2

Total C02 Items: 2

Plan Report Page 10

1210612000

EOC 13

CATEGORY C-C, Integral Attachments For Vessels, Piping, Pumps. And Valves




McGuire 2

Inservice Inspection-Plan for Interval 2 Outage 5

PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

**** Integrally Welded Attachments **** C03.020.010 2MCA-ND-6123 ND MCFI-2ND18

2MCA-Nr)-6123

Class B

NDE-35 PT SS-CS- *1fflfl A A*.-r* flt IRArLET

I �3I¶ML P� I I IW�flIVI�IN Iu.UUU 1.000

I I

Total C03.020 Items:

Total C03 Items:

Plan Report Page 11

1210612000

IN I M-UMA/L M I I/%.,MIVII-IN I

EOC 13

CATEGORY C-F-I, Pressure Retaining Welds In Austenitic SS or High Alloy Piping EPloInc Welds >= 318 in. Nominal Wall ThicknessITNor Piping > NPS 4 ITEM NUMBER ID NUMBER SYS ISOIDWG NUMBERS



McGuire 2

Inservice Inspection Plan for Interval 2 Outage 5PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS

**** Circumferential Weld C05.01 1.021 2NDP109-1


ND MCFI-2ND10 NDE-600 UT SS STD

Elbow to Pipe

C05.011.021A 2NDP109-1 ND MCFI-2ND10 NDE-35 PT SS 12.000

Circumferential STD 0.375

Class B Elbow to Pipe

C05.011.030 2ND2F-202 ND MCFI-2ND10 NDE-600 UT SS 12.000 *See Section 8 for Calibration Block Requirements


Class B Pipe to Elbow

C05.011.030A 2ND2F-202 ND MCFI-2ND10 NDE-35 PT SS 12.000



C05.011.034 2ND2FW16-18 ND MCFI-2ND16 NDE-600 UT SS 12.000 50313



C05.011.034A 2ND2FW16-18 ND MCFI-2ND16 NDE-35 PT SS 12.000



C05.011.104 2N12F440 NI MCFI-2NI14 NDE-600 UT SS 6.000 50211


Class B Reducer to Pipe

C05.011.104A 2N12F440 NI MCFI-2NI14 NDE-35 PT SS 6.000Circumferential

Class B

160 Reducer to Pipe

0.719

Plan Report Page 12

1210612000

12.000 0.375

50313

SYS ISO/DWG NUMBERS

EOC 13

CATEGORY C-F-t, Pressure Retaining Welds In Austenitic SS or High Alloy Piping Wiping Welds >= 318 in. Nominal Wall Thickness



McGuire 2Plan Report

Page 13 .4 'lnlI*Jnnn

Wor Piping > NPS 4 Inservice Inspection Plan for Interval 2 Outage 5 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS

C05.011.126 2NIP145-1 NI MCFI-2NI16 NDE-600 UT SS 6.000 50211 Circumferential 160 0.719


C05.011.126A 2NIP145-1 NI MCFI-2NI16 NDE-35 PT SS 6.000 Circumferential 160 0.719


C05.011.129 2NI2F493 NI MCFI-2NI16 NDE-600 UT SS 6.000 50211 Circumferential 160 0.719

Class B Pipe to Valve 2NI181

C05.011.129A 2NI2F493 NI MCFI-2NI16 NDE-35 PT SS 6.000 Circumferential 160 0.719

Class B Pipe to Valve 2NI181

C05.011.151 2NI2FW26-4 NI MCFI-2NI26 NDE-600 UT SS 12.000 50219 Circumferential 140 1.125

Class B Tee to Reducer

C05.011.151A 2NI2FW26-4 NI MCFI-2NI26 NDE-35 PT SS 12.000

Circumferential 140 1.125 Class B Tee to

Reducer

C05.011.152 2NI2FW26-10 NI MCFI-2NI26 NDE-600 UT SS 12.000 50219 Circumferential 140 1.125


C05.011.152A 2NI2FW26-10 NI MCFI-2NI26 NDE-35 PT SS 12.000 Circumferential 140 1.125


C05.011.159 2N12F449 NI MCFI-2NI14 NDE-600 UT SS 6.000 *See Section 8 for Calibration Block Requirements

CircumferentialClass B

160 0.719Pipe to Elbow

EOC 13

CATEGORY C-F-1, Pressure Retaining Welds In Austenitic SS or High Alloy Piping Wiping Welds >= 318 in. Nominal Wall Thickness



McGuire 2

Wor Piping > NPS 4 Inservice Inspection Plan for Interval 2 Outage 5 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

C05.011.159A 2N12F449 NI MCFI-2NI14 NDE-35 PT SS 6.000 Circumferential 160 0.719


C05.0i1.163 2N12F443 NI MCFI-2NI14 NDE-600 UT SS 6.000 Circumferential 160 0.719




C05.011.164 2N12F590 NI MCFI-2NI20 NDE-600 UT SS 12.000 Circumferential 140 1.125

Class B Elbow to Tee

C05.011.164A 2NI2F590 NI MCFI-2NI20 NDE-35 PT SS 12.000 Circumferential 140 1.125

Class B Elbow to Tee

C05.011.165 2NI2F591 NI MCFI-2NI20 NDE-600 UT SS 12.000


Class B Tee to Pipe

C05.011.165A 2N12F591 NI MCFI-2NI20 NDE-35 PT SS 12.000


Class B Tee to Pipe


Plan Report Page 14

S'fidflti'lnnn

EOC 13

CATEGORY C-F-I, Pressure Retaining Welds In Austenitic SS or High Alloy Piping WPiping Welds > 115 in. Nom Wall For Piping >=

"*NPS 2 And <= NPS 4 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS



McGuire 2


**** Circumferential Weld ****

C05.021.008 2NI2F535 Circumferential

Class B

NI MCFI-2NI17 4.000 0.531

NDE-600 UT SS 160

Tee to Reducer



C05.021.017 2N12F-693 NI MCFI-2NI2 NDE-600 UT SS 4.000 50436


Class B Reducer to Elbow

C05.021.017A 2N12F-693 NI MCFI-2NI2 NDE-35 PT SS 4.000


Class B Reducer to Elbow

C05.021.063 2NV2FW116-2 NV MCFI-2NV116 NDE-600 UT SS 3.000 50225



C05.021.063A 2NV2FW116-2 NV MCFI-2NV116 NDE-35 PT SS 3.000 Circumferential 160 0.438


C05.021.072 2NV2FW292-3 NV MCFI-2NV292 NDE-600 UT SS 3.000 50225 Circumferential 160 0.438

Class B Elbow to Elbow

C05.021.072A 2NV2FW292-3 NV MCFI-2NV292 NDE-35 PT SS 3.000Circumferential

Class B

160 Elbow to Elbow

0.438

Plan Report Page 15

1210612000

50275

EOC 13

CATEGORY C-F-I, Pressure Retaining Welds In Austenitic SS or High Alloy Piping *PiDinq Welds > 1/5 in. Nom Wall For PiDina >=MNPS 2 And <= NPS 4



McGuire 2

Inservice Inspection Plan for Interval 2 Outage 5ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

C05.021.081 2RCPA-TE NV MCFI-2NV69 NDE-600 UT SS 3.000 50225 FOR DWG. ON RECIPROCATING CHARGING

Circumferential 160 0.438 PUMP ACCUMULATOR SEE MCM 1201.04-0197

Class B Term end Tee to RCHP ACCUMULATOR

C05.021.081A 2RCPA-TE NV MCFI-2NV69 NDE-35 PT SS 3.000 FOR DWG. ON RECIPROCATING CHARGING

Circumferential 160 0.438 PUMP ACCUMULATOR SEE MCM 1201.04-0197

Class B Term end Tee to RCHP ACCUMULATOR

C05.021.087 2NV2FW33-23 NV MCFI-2NV33 NDE-600 UT SS 4.000



C05.021.087A 2NV2FW33-23 NV MCFI-2NV33 NDE-35 PT SS 4.000



C05.021.090 2NV2FW101-1 NV MCFI-2NV101 NDE-600 UT SS 4.000 50275 Circumferential 160 0.531

Class B Pipe to Reducer


Circumferential 160 0.531 Class B Pipe to

Reducer

C05.021.099 2NV2FW54-16 NV MCFI-2NV54 NDE-600 UT SS 4.000 50275

Circumferential 160 0.531 Class B Reducer to

Elbow


Circumferential 160 0.531 Class B Reducer to

Elbow


Plan Report Page 16

1210612000

EOC 13

CATEGORY C-F-I, Pressure Retaining Welds In Austenitic SS or High Alloy Piping

Socket Welds

ITEM NUMBER ID NUMBER SYS ISO/DW(• NUMBERS



McGuire 2


C05.030.008 2N12FW33-9

Socket Class B

NI MCFI-2NI33 NDE-35 PT SS 160

Pipe to Full Coupling

C05.030.052 2NV2FW101-7 NV MCFI-2NV101 NDE-35 PT SS 2.000

Socket 160 0.344

Class B Pipe to Tee

C05.030.061 2NVP182-1 NV MCFI-2NV180 NDE-35 PT SS 2.000

Socket 160 0.344

Class B Pipe to Flange


Socket 160 0.344



Socket 160 0.344

Class B Tee to Pipe

Total 005.030 Items: 5

Plan Report Page 17

1210612000

2.000 0.344

EOC 13

CATEGORY C-F-2. Pressure Retaining Welds In Carbon Or Low Alloy Steel PipingWiping Welds >= 318 in. Nominal Wall ThicknessITor PipingN > NPS 4 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS



McGuire 2


**** Circumferential Weld ****

C05.051.002 2CA2FW45-27 CA MCFI-2CA45 NDE-600 UT CS 6.000 50331


Class B Valve 2CF128B to Pipe

C05.051.002A 2CA2FW45-27 CA MCFI-2CA45 NDE-25 MT CS 6.000


Class B Valve 2CF128B to Pipe



Class B Tee to Elbow

C05,051.003A 2CA2FW45-21 CA MCFI-2CA45 NDE-25 MT CS 6.000


Class B Tee to Elbow



Class B Term end Elbow to Nozzle SG-2C

C05.051.011A 2CA2FW51-25 CA MCFI-2CA51 NDE-25 MT CS 6.000


Class B Term end Elbow to Nozzle SG-2C

C05.051.204 2SM5C-D SM MCFI-2SM13 NDE-600 UT CS 10.000 50249


1.500 Nozzle Forged nozzle to Transition piece

C05.051.204A 2SM5C-D


SM MCFI-2SM13 NDE-25 MT CS

Nozzle Forged nozzle to Transition piece

Plan Report Page 18

12/0612000

10.000 1.500

EOC 13

CATEGORY C-F-2, Pressure Retainina Welds In Carbon Or Low Alloy Steel Piping Wping Welds >= 3/8 in. Nominal Wall Thickness




Page 19 4 lfnl~ngnn

Ufor Piping > NPS 4 Inservice Inspection Plan for Interval 2 Outage 5 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

C05.051.209 2SM2F-22 SM MCFI-2SM50 NDE-12 RT CS 32.000

Circumferential MCFD 2591-01.01 1.375

Class B Transition Ring to Elbow

C05.051.209A 2SM2F-22 SM MCFI-2SM50 NDE-25 MT CS 32.000


Class B Transition Ring to Elbow

C05.051.215 2SM2F-72 SM MCFI-2SM3 NDE-600 UT CS 34.000 40415



C05.051.215A 2SM2F-72 SM MCFI-2SM3 NDE-25 MT CS 34.000



C05.051.217 2SM2FW13-10 SM MCFI-2SM13 NDE-600 UT CS 36.000 50385

Circumferential 2.437

Class B Pipe to Valve 2SM3AB

C05.051.217A 2SM2FW13-10 SM MCFI-2SM13 NDE-25 MT CS 36.000

Circumferential 2.437

Class B Pipe to Valve 2SM3AB

C05.051.220 2SGA-W1 38 SM MCFI-2SM50 NDE-600 UT CS 32.625 Steam Generator 2A

Circumferential MCFD-2591-01.01 1.500 Main Ssteam Nozzle to

Class B Term end MCM 2201.01-0207 2S/G-A Nozzle to Transition Ring

Transition Ring Transition Ring added as a result of SGRP *Reference General Requirements Section 8.1.10

C05.051.220A 2SGA-W138 SM MCFI-2SM50 NDE-25 MT CS 32.625 Steam Generator 2A

Circumferential Class B Term end

MCFD-2591-01.01 MCM 2201.01-0207

1.500

2S/G-A to Transition Ring

Main Ssteam Nozzle to Transition Ring Transition Ring added as a result of SGRP

EOC 13

CATEGORY C-F-2. Pressure Retaining Welds In Carbon Or Low Alloy Steel Piping *Pi•Jin-q Welds >= 318 in. Nominal Wall Thickness




Page 20 4 •l5 llal~inn

*or Piping> NPS 4 Inservice Inspection Plan for Interval 2 Outage 5 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

C05.051.252 2SV2FW9-7 SV MCFI-2SV9 NDE-600 UT CS 6.000 50281

Circumferential XXS 0.864

Class B Pipe to Valve 2SV19

C05.051.252A 2SV2FW9-7 SV MCFI-2SV9 NDE-25 MT CS 6.000 Circumferential XXS 0.864

Class B Pipe to Valve 2SVI 9

C05.051.300 2VP2FW1-4 VP MCFI-2VP1 NDE-600 UT CS 12.000 50440


Class B Flange to Pipe

C05.051.300A 2VP2FWI-4 VP MCFI-2VP1 NDE-25 MT CS 12.000 Circumferential STD 0.375


C05.051.301 2VP2FW2-1 VP MCFI-2VP2 NDE-600 UT CS 24.000 * REFERENCE 8.1.10 OF GENERAL

Circumferential STD 0.375 REQUIREMENTS


C05.051.301A 2VP2FW2-1 VP MCFI-2VP2 NDE-25 MT CS 24.000



Total C05.051 Items:

Total C05 Items:

22

67

EOC 13

CATEGORY D-B, Systems In Support Of ECC, CHR, Atmos. Cleanup, And Reactor RHR E Integral Attachment




McGuire 2

Inservice Inspection Plan for Interval 2 Outage 5 PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS

**** Component Supports and Restraints **** D02.020.040 2MCA-RN-3083 RN 2RN-351 QAL-14 VT-3 NA 0.000 RIGID RESTRAINT

Rigid Restraint (SHT.20F3) 0.594 PIPE ATT.

Class C

D02.020.041 2MCA-RN-3086 RN 2RN-351 QAL-14 VT-3 NA 0.000 RIGID SUPPORT Rigid Support (SHT.20F3) 0.375 PIPE ATT.

Class C

Total D02.020 Items: 2

Plan Report Page 21

1210612000

Total D02 Items: 2

EOC 13

CATEGORY F-A, Supports

MClass 1 Pipn upot

ITEM NUMBER ID NUMBER

F01.010.102A 2MCR-NV-4443 Rigid Support

Class A

(Categiory A)

SYS ISO/DWG NUMBERS

NV 2NV-204(SHT.1OF3)



McGuire 2

Inservice Inspection Plan for Interval 2 Outage 5 PROC INSP REQ MAT/SCH DIANTHK CAL BLOCKS COMMENTS

QAL-14 VT-3 NA 2.000 0.000

F01.010.103A 2MCR-NV-4438 NV 2NV-204(SHT.1OF3) QAL-14 VT-3 NA 3.000

Rigid Support 0.000

Class A

Total F01.010 Items: 2

Plan Report Page 22

12/0612000

EOC 13

CATEGORY F-A, Supports (Categorv A)

MClass 2 PiNUMBE Su

ITEM NUMBER ID NUME3ER SYS ISO/DWG NUMBERS



McGuire 2


F01.020.078B 2MCA-FW-5009 FW 2FW-350 SHT.1 QAL-14 VT-3 NA 0.000

Mech Snubber 0.000

Class B

F01.020.079C 2MCA-FW-5160 FW 2FW-350 SHT.2 QAL-14 VT-3 NA 0.000

Spring Hgr 0.000

Class B

F01.020.080C 2MCA-FW-5180 FW 2FW-350 SHT.2 QAL-14 VT-3 NA 0.000

Hyd Snubber 0.000

Class B

F01.020.108B 2MCA-ND-6108 ND 2ND-350(SHT.10F7) QAL-14 VT-3 NA 8.000

Rigid Restraint 0.000

Class B

F01.020.122B 2MCA-ND-6117 ND 2ND-350(SHT.7OF7) QAL-14 VT-3 NA 8.000


Class B

F01.020.224B 2MCA-NS-5305 NS 2NS-352(SHT.10F2) QAL-14 VT-3 NA 10.000


Class B

F01.020.225B 2MCA-NS-5308 NS 2NS-352(SHT.2OF2) QAL-14 VT-3 NA 8.000


Class B

F01.020.250A 2-MCA-S-NI-504-I-K NV 2-MCA-S-NI-504-I-RD7 QAL-14 VT-3 NA 2.000

Rigid Restraint Class B

0.000

Plan Report Page 23

12106/2000

EOC 13

CATEGORY F-A. SuDiorts (Cateqory A)DUKE ENERGY CORPORATION

QUALITY ASSURANCE TECHNICAL SERVICES Inservice Inspection Database Management System

MClass 2 pi McGuire 2 Page 24 E Inservice Inspection Plan for Interval 2 Outage 5 12/0612000


F01.020.251C 2-MCA-S-NI-504-I-L NV 2-MCA-S-NI-504-I-RD7 QAL-14 VT-3 NA 2.000

Mech Snubber 0.000 Class B

F01.020.264A 2MCR-NV-5191 NV 2NV-201(SHT.2OF2) QAL-14 VT-3 NA 2.000 Rigid Support 0.000

Class B


Plan Report

EOC 13

CATEGORY F-A. SuDDorts

Class 3 Piping Supports

ITEM NUMBER ID NUME

(Category A)

EER SYS ISO/DWG NUMBERS



McGuire 2


F01.030.154B 2MCA-RN-3028 RN 2RN-351(SHT.1OF3) QAL-14 VT-3 NA 20.000


Class C



Class C

F01.030.156A 2MCA-RN-3086 RN 2RN-351(SHT.2OF3) QAL-14 VT-3 NA 18.000


Class C



Class C


Plan Report Page 25

1210612000

EOC 13

CATEGORY F-A, Supports

mSupports other than Piping SupDorts (Class 1. 2.

IT~FhA NIl IRA~tE lfl Nil I!�AP�P � I�C�IflWC NUMRFRS



McGuire 2


PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS

F01.040.005 2RCP-B-SUPPORT NC MC 1070-7

Class A

F01.040.023 2RNP-SUP-2B RN

OAL-14 VTI-3N/�L u.uuiJ

MC 1070-8 MC 1070-17

QAL-14 VT-3 NAMC1201.05-190

U.UUU 0.000

u.uuu0.000 0.000

2B RCP SUPPORT COLUMN ASSEMBLIES AND LATERAL SUPPORT HANGER FUNCTION CATEGORIZATION B

2B NUCLEAR SERVICE WATER PUMP SUPPORT HANGER FUNCTION CATEGORIZATION B

Class C

Total F01.040 Items:

Plan Report Page 26

1210612000

Total F01 Items:

2

18

In KIHhA9Zr:P SYS ISO/DWG NUMBERS

NA

5.0 Results Of Inspections Performed

The results of each examination shown in the final ISl Plan (Section 4 of this report) are included in this section. The completion date and status for each examination are shown. Limited examinations are described in further detail in Section 5.2. All examinations revealing reportable indications are described in further detail in Section 6.

5.1 The information shown below is a field description for the reporting format included in this section of the report:

Item Number

ID Number

Insp Date

Insp Status

Insp Limited

Geo. Ref. (Geometric Reflector applies only to UT)

Comments

= ASME Section XI Tables IWB-2500-1 (Class 1), IWC-2500-1 (Class 2), IWF2500-1 (Class I and Class 2), Augmented Requirements

= Unique Identification Number

= Date of Examination

= CLR Clear REC Recordable REP Reportable

= Indicates inspection was limited. Coverage obtained is listed

= �Y Yes N No




EOC 13

Plant: McGuire 2

ITEM NUMBER

B06.100.001

B06.100.002

B06.100.003

B06.100.004

B06.100.005

B06.100.006

B06.100.007

B06.100.008

B07.070.0038

B09.01 1.010

B09.011.01 OA

B09.01 1.010B

B09.011.031

B09.011.031A

B09.011.032

B09.011.032A

B09.011.034

B09.011.034A

B09.011.035

B09.011.035A

B09.011.036

B09.011.036A

B09.011.037

B09.011.037A

B09.011.038

B09.011.038A

B09.011.039

B09.011.039A

B09.011.162

B09.011.162A

B09.011.163

B09.011.163A

B09.011.164

B09.011.164A

B09.011.165

B09.011.165A

809.011.166

Run D Page 1

12/0612000

ID NUMBER 2SGA-MW-YI-Xl

2SGA-MW-X1-Y2

2SGB-MW-YI-X2

2SGB-MW-X2-Y2

2SGC-MW-YI-Xl

2SGC-MW-XI-Y2

2SGD-MW-YI-X2

2SGD-MW-X2-Y2

2NC-34A

2NC2FW2-3

2NC2FW2-3

2NC2FW2-3

2NC2FW53-24

2NC2FW53-24

2NC2FW53-25

2NC2FW53-25

2NC2FW53-28

2NC2FW53-28

2NC2FW53-29

2NC2FW53-29

2NC2FW53-30

2NC2FW53-30

2NC2FW53-31

2NC2FW53-31

2NC2FW53-36

2NC2FW53-36

2NC2FW53-37

2NC2FW53-37

2N12F471

2N12F471

2N12F474

2N12F474

2N12F477

2N12F477

2N12F494

2NI2F494

2N12F496

DUKE ENER(% JRPORATION QUALITY ASSURANCE TECHNICAL SERVICES

In-Service Inspection Database Management System McGuire 2 Inservice Inspection Listing

Interval 2 Outage 5

SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS

NC 09/21/2000 CLR -- N N

NC 09/21/2000 CLR --- N N

NC 09/20/2000 CLR -- N N

NC 09/20/2000 CLR --- N N

NC 09/25/2000 CLR --- N N

NC 09/25/2000 CLR -- N N

NC 09/22/2000 CLR --- N N

NC 09/22/2000 CLR --- N N

NC 09/28/2000 CLR --- N N

NC 09/21/2000 CLR --- N N

NC 09/21/2000 CLR --- N N

NC 09/21/2000 CLR --- N N

NC 09/20/2000 CLR --- N N

NC 09/20/2000 CLR -- N N

NC 09/20/2000 CLR 60.30% N Y

NC 09/20/2000 CLR -- N N

NC 09/20/2000 CLR --- N N

NC 09/20/2000 CLR -- N N

NC 09/20/2000 CLR --- N N

NC 09/20/2000 CLR -- N N

NC 09/20/2000 CLR -- N N

NC 09/20/2000 CLR --- N N

NC 09/2012000 CLR -- N N

NC 09/20/2000 CLR --- N N

NC 09/20/2000 CLR --- N N

NC 09/20/2000 CLR --- N N

NC 09/20/2000 CLR 60.30% N Y

NC 09/20/2000 CLR --- N N

NI 09/12/2000 CLR 59.70% N Y

NI 09/12/2000 CLR --- N N

NI 09/07/2000 CLR - N N

NI 09/07/2000 CLR --- N N

NI 09/0712000 REC -- Y N

NI 09/07/2000 CLR --- N N

NI 09/12/2000 CLR 59.61% N Y

NI 09/12/2000 CLR - N N

NI 09/12/2000 REC -- Y N

EOC 13

Plant: McGuire 2

ITEM NUMBER B09.011.166A

B09.011.167

B09.011.167A

B09.040.006

B09.040.017

B09.040.018

B09.040.050

B09.040.051

B09.040.052

B09.040.053

B09.040.054

B09.040.055

B09.040.056

C01.030.011

C01.030.012

C02:021.007

C02.021.007A

C03.020.010

C05.011.021

C05.011.021A

C05.011.030

C05.011.030A

C05.011.034

C05.011.034A

C05.011.104

C05.011.104A

C05.011.126

C05.011.126A

C05.011.129

C05.011.129A

C05.011.151

C05.011.151A

C05.011.152

C05.011.152A

C05.011.159

C05.011.159A

C05.011.163

Run D Page 2

12/0612000

ID NUMBER

2N12F496

2N12F866

2N12F866

2NC2FW40-1

2NC2FW40-12

2NC2FW40-14

2N12FW89-1

2N12FW89-3

2NI2FW89-4

2N12FW89-5

2N12FW89-6

2N12FW89-7

2N12FW89-8

2BCSHX-50-B

2BCSHX-50-A

2SGC-W259

2SGC-W259

2MCA-ND-6123

2NDP109-1

2NDPI09-1

2ND2F-202

2ND2F-202

2ND2FW16-18

2ND2FW16-18

2N12F440

2NI2F440

2NIP145-1

2NIP145-1

2N12F493

2N12F493

2N12FW26-4

2N12FW26-4

2N12FW26-10

2NI2FW26-10

2N12F449

2N12F449

2N12F443

DUKE ENERs- .ORPORATION QUALITY ASSURANCE TECHNICAL SERVICES


Interval 2 Outage 5 SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS

NI 09/12/2000 CLR -- N N

NI 09/12/2000 CLR --- N N

NI 09/12/2000 CLR -- N N

NC 09/18/2000 CLR -- N N

NC 09/08/2000 CLR --- N N

NC 09/08/2000 CLR --- N N

NI 09/08/2000 CLR -- N N

NI 09/08/2000 CLR --- N N

NI 09/08/2000 CLR -- N N

NI 09/18/2000 CLR --- N N

NI 09/18/2000 CLR --- N N

NI 09/18/2000 CLR -- N N

N I 09/18/2000 CLR -- N N

NS 08/29/2000 REC --- Y N

NS 08/29/2000 REC -- Y N

SM 09/23/2000 CLR 74.40% N Y SM 09/22/2000 CLR -- N N

ND 08/31/2000 CLR --- N N

ND 08/29/2000 CLR --- N N

ND 08/29/2000 CLR --- N N

ND 08/29/2000 CLR --- N N

ND 08/29/2000 CLR --- N N

ND 08/30/2000 CLR -- N N

ND 08/30/2000 CLR --- N N

N I 09/13/2000 CLR -- N N

NI 09113/2000 CLR -- N N

NI 09/16/2000 CLR -- N N

NI 09/16/2000 CLR --- N N

N I 09/12/2000 CLR 59.86% N Y NI 09/12/2000 CLR -- N N

N I 09/13/2000 CLR --- N N

NI 09/1312000 CLR --- N N

N I 09/13/2000 CLR --- N N

N I 09/13/2000 CLR --- N N

N I 09/13/2000 CLR --- N N

N I 09/13/2000 CLR - N N

N I 09/13/2000 CLR --- N N

EOC 13

Plant: McGuire 2

ITEM NUMBER ID NUMBER C05.011.163A 2N12F443 C05.011.164 2N12F590 C05.011.164A 2N12F590

C05.011.165 2N12F591 C05.011.165A 2N12F591 C05.021.008 2N12F535 C05.021.008A 2N12F535 C05.021.017 2N12F-693 C05.021.017A 2N12F-693 C05.021.063 2NV2FW1 16-2 C05.021.063A 2NV2FWI 16-2 C05.021.072 2NV2FW292-3 C05.021.072A 2NV2FW292-3 C05.021.081 2RCPA-TE C05.021.081A 2RCPA-TE C05.021.087 2NV2FW33-23

C05.021.087A 2NV2FW33-23 C05.021.090 2NV2FW101-1

C05.021.090A 2NV2FW101-1 C05.021.099 2NV2FW54-16

C05.021.099A 2NV2FW54-16 C05.030.008 2NI2FW33-9 C05.030.052 2NV2FW101-7 C05.030.061 2NVP182-1 C05.030.070 2NV2FW235-4 C05.030.079 2NV2FW303-15 C05.051.002 2CA2FW45-27 C05.051.002A 2CA2FW45-27 C05.051.003 2CA2FW45-21 C05.051.003A 2CA2FW45-21 C05.051.011 2CA2FW51-25 C05.051.011A 2CA2FW51-25 C05.051.204 2SM5C-D

C05.051.204A 2SM5C-D C05.051.209 2SM2F-22 C05.051.209A 2SM2F-22 C05.051.215 2SM2F-72

Run D Page 3

1210612000

DUKE ENERL ,ORPORATION QUALITY ASSURANCE TECHNICAL SERVICES


Interval 2 Outage 5 SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS

NI 09/13/2000 CLR -- N N

NI 08/31/2000 REC --- Y N

NI 08/30/2000 CLR --- N N

NI 08/31/2000 CLR --- N N

NI 08/30/2000 CLR --- N N

NI 09W16/2000 CLR -- N N

NI 09/16/2000 CLR -- N N

NI 08/31/2000 CLR -- N N

NI 08/31/2000 CLR --- N N

NV 09/26/2000 CLR -- N N

NV 09/26/2000 CLR --- N N

NV 08/30/2000 CLR -- N N

NV 08/30/2000 CLR -- N N

NV 08/31/2000 CLR 58.17% N Y NV 08/31/2000 CLR --- N N

NV 08/31/2000 CLR --- N N

NV 08/31/2000 CLR --- N N

NV 09/16/2000 CLR --- N N

NV 09/16/2000 CLR --- N N

NV 09/06/2000 CLR --- N N

NV 09/06/2000 CLR --- N N

NI 09/13/2000 CLR --- N N

NV 09/16/2000 CLR --- N N

NV 09/06/2000 CLR --- N N

NV 09/16/2000 CLR --- N N

NV 08/31/2000 CLR --- N N

CA 09/16/2000 REC -- Y N

CA 09/16/2000 CLR --- N N

CA 09/15/2000 CLR --- N N

CA 09/15/2000 CLR -- N N

CA 09/23/2000 REC -- Y N

CA 09/23/2000 CLR -- N N

SM 09/15/2000 CLR --- N N

SM 09/15/2000 CLR - N N

SM 09/17/2000 REC -- N N

SM 09/16/2000 CLR -- N N

SM 09/09/2000 CLR - N N

EOC 13

Plant: McGuire 2

ITEM NUMBER C05.051.215A C05.051.217 C05.051.217A C05.051.220 C05.051.220A C05.051.252 C05.051.252A C05.051.300 C05,051.300A C05.051.301 C05.051.301A D02.020.040 D02.020.041 F01.010.102A F01.010.103A F01.020.078B F01.020.079C F01.020.080C F01.020.108B F01.020.1228 F01.020.224B F01.020.225B F01.020.250A F01.020.251C F01.020.264A F01o.030.154B F01.030.155B F01.030.156A F01.030.157B F01.040.005 F01.040.023

DUKE ENERG. JRPORATION lUALITY ASSURANCE TECHNICAL SERVICES ervice Inspection Database Management System

McGuire 2 Inservice Inspection Listing Interval 2 Outage 5

INSP STATUS INSP LIMITED GEO REF RFRID NUMBER 2SM2F-72

2SM2FW13-10

2SM2FW13-10

2SGA-W138

2SGA-W138

2SV2FW9-7

2SV2FW9-7

2VP2FW1-4

2VP2FW1-4

2VP2FW2-1

2VP2FW2-1

2MCA-RN-3083

2MCA-RN-3086

2MCR-NV-4443

2MCR-NV-4438

2MCA-FW-5009

2MCA-FW-5160

2MCA-FW-5180

2MCA-ND-6108

2MCA-ND-6117

2MCA-NS-5305

2MCA-NS-5308

2-MCA-S-NI-504-I-K

2-MCA-S-NI-504-I-L

2MCR-NV-5191

2MCA-RN-3028

2MCA-RN-3083

2MCA-RN-3086

2MCA-RN-3045

2RCP-B-SUPPORT

2RNP-SUP-2B

SYSTEM SM SM SM SM SM SV SV VP VP VP VP RN RN NV NV FW FW FW ND ND NS NS NV NV NV RN RN RN RN NC RN

C In-S

INSP DATE 09/08/2000 09/1512000 09/15/2000 09/16/2000 09/16/2000 09/15/2000 09/15/2000 09/07/2000 09/07/2000 09/07/2000 09/07/2000 08/30/2000 08/22/2000 09/02/2000 09/06/2000 08/22/2000 08/22/2000 08/22/2000 08/22/2000 08/22/2000 08/22/2000 08/22/2000 08/22/2000 08/22/2000 09/06/2000 08/22/2000 08/30/2000 08/22/2000 08/22/2000 09/06/2000 08/22/2000

CLR CLR CLR CLR CLR

CLR CLR CLR CLR CLR CLR

CLR

CLR CLR

CLR CLR CLR

CLR CLR CLR

CLR CLR CLR CLR CLR REC

CLR

CLR

CLR

CLR

CLR

N N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N

Run D Page 4

12/0612000

COMMENTS

5.2 Limited examinations (i.e., 90% or less of the required examination coverage obtained) identified during Outage 5/EOC-13 are shown below. A Request for Relief will be submitted for NRC approval. Reference Section 9 for additional information.

Item Number

B09.011.032

B09.011.039

B09.011.162

B09.011.165

C02.021.007

C05.011.129

C05.021.081

Request for Relief Serial Number

01-001

01-001

01-001

01-001

01-001

01-001

01-001



6.0 Reportable Indications

Outage 5/EOC-1 3 had no reportable indications.



7.0 Personnel. Equipment and Material Certifications

All personnel who performed or evaluated the results of inservice inspections from to April 16, 1999 to October 13, 2000 at McGuire Nuclear Station, Unit 2, were certified in accordance with the requirements of the 1989 Edition of ASME Section Xl with no addenda including Appendix VII for ultrasonic inspections. In addition, ultrasonic examiners were qualified in accordance with ASME Section XI, Appendix VIII, and 1992 Edition with the 1993 Addenda through the Performance Demonstration Initiative (PDI) for similar metal piping welds. The appropriate certification records for each inspector are on file at McGuire Nuclear Station or copies can be obtained by contacting the Duke Energy's Corporate Office in Charlotte, North Carolina.

Records of periodic calibration of inspection equipment are on file at Nuclear Station or copies can be obtained by contacting the Duke Corporate Office in Charlotte, North Carolina.

Records of materials used, (i.e., NDE consumables) are on file at Nuclear Station or copies can be obtained by contacting the Duke Corporate Office in Charlotte, North Carolina.

McGuire Energy's

McGuire Energy's

Outage 5IEOC-13 McGuire Unit 2 Section 7


8.0 Corrective Action

No corrective action was required as a result of examinations performed during Outage 5/EOC-13.

Outage 5[EOC-13 McGuire Unit 2 Section 8


9.0 Reference Documents

The following reference documents apply to the inservice inspection performed during Outage 5/EOC-1 3 at McGuire Unit 2. A copy of these can be obtained by contacting the ISI Plan Manager at Duke Energy's Corporate Office in Charlotte, North Carolina:

Request for Relief 01-001



10.0 Class I and 2 Repairs and Replacements

As required by ASME Section Xl 1989 Edition, no Addenda, a record of (Form NIS-2) the Class I and Class 2 Repairs and Replacements for work performed from April 16, 1999 to October 13, 2000 is provided and is included in this section of the report. The individual work request documents are on file at McGuire Nuclear Station.



FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section X1

1. Owner Address: Duke Power Company

526 S. Church Street, Charlotte, NC 28201-1006

2. Plant Address:

la. Date May 18, 1999 Sheet 1 of I

McGuire Nuclear Station

12700 Hagers Ferry Road, Huntersville, NC 28078

2a. Unit: 01 E12 03 r'Shared (specify Units _

3. Work Performed By: Duke Power Company 3a. Work Order#:

Address: 526 S. Church Street, Charlotte NC 28201-100698043857

RepeJr Oganiz Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A

4. (a) Identification of System: NC - Reactor Coolant 4. (b)

5. (a) Applicable Construction Code: AWE HI 197t Edition, Summer and Winter Addenda,

(b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989, No Addenda

6. Identification of Components Repaired or Replaced and Replacement Components:

3b. NSM or MM #:

Class of System: A

N/A

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Repaired, Replaced, or ASME Code Stamped

Replacement (yes or no)

A E Repaired, 03 No 2A Steam Generator B&W 770002 159 N/A 1996 03 Replaced,

__Replacement 0Yes B 0 Repaired, 03 No

o3 Replaced,

[] Replacement 0 Yes

C 0 Repaired, 0 No o Replaced, [o Replacement 0 Yes r-I E3 h,,- I--r ki

O3 Replaced, O Replacement

________________ -t t "r � .�. I U t-tepairea, Li NOR epaired, "0 Replaced,

"0 Replacement_____ .1 1 I t.-. - -. u I-¶epaireU, U P40

uRtepalreu, "0 Replaced, "O Replacement

03 Yes

U NO

13 Yes

N Yo

0 Yes

Page I of 2 Revision 5

N/A

Code Cases

D

E

F

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in itemsl through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced Studs

8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. 0

9. Remarks

Other 0 Exempto

Pressure _ __psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

(Applicable Manufacturer's Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the ASME Code, Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A

Signed ,.ý Q FL Grass Jr.,QA Tech Specialist Date h,/ , 19 Owner odvwners Designee, Weite


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected th omponents described in this Owners Report during the period A ý .4 tcto. S±--2 ; and state that to the best of my knowledge and belief, the Owner has performed examinatiohs and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

"Commissions r%7"7dý o 1 Q3C '3", --Inspec or'" ature National Board, State, Province and Endorsements

Date 1.9-YT

FORM NIS-2 OWNER'S hr-PORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section Xl



2. Plant Address:

la. Date May18,1999

Sheet 1 of 1


12700 Hagers Ferry Road, Huntersvtlle, NO 28078

2a. Unit: 01 E12 03 OShared (specify Units

3. Work Performed By: Duke Power Company Address: 526 S. Church Street, Charlotte NC 28201-1006


4. (a) Identification of System: NC - Reactor Colloant

3a. Work Order#:

3b. NSM or MM

4. (b) Class of System: A

98043858 R~epr Organizs~wr Job #

N/A

5. (a) Applicable Construction Code: ASME II1971 Edition, Summer and Winter Addenda,. (b) Applicable Edition of Section XI Utilized for Repairs or Replacements: 1989, No Addenda


N/A Code Cases


Replacement (yes or no) A 0 Repaired, 0 No

28 Steam Generator B&W 770004 161 N/A 1996 0 Replaced, EReplacement 0Yes

B 0 Repaired, 0 No o Replaced,

__ Replacement 0 Yes C 0 Repaired, 0 No

0 Replaced,

[0 Replacement 0 Yes

D 0 Repaired, 0 No 0[ Replaced, [o Replacement 0 Yes

E 0 Repaired, 0 No 0 Replaced, ]0 Replacement 0 Yes

F 0 Repaired, 0 No o Replaced, _0 Replacement 0 Yes


Form NIS-2 (Back)


7. Description of WorkRDlaced stud #16R

8. Test Conducted:Hydrostatic 0 Pneumatic l1 Nom. Operating Press. 9 Oither 11 Exemptol

9. Remarks

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF


CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the ASME Code, Section Xl.


Signed FL Grass Jr..QA Tech Specialist Date 5 '/ 19 Owneror• Owner's Designee, Title


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connectict ,ha e inspected the,,components described in this Owner's Report during the period - -P- to,.a -F -FY; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissions MZ77aý4 ,/3-7 fns t r' S' ture 0e- National Board, Stat4, Province and Endorsements

Date 12P 1917

-

-- ! ........... ., ov

FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section Xl



2. Plant Address:

la. Date May18,1999

Sheet 1 of 1


12700 Haners Ferry Road, Huntersville, NC 28078

2a. Unit: 01 122 03 OShared (specify Units

3. Work Performed By: Duke Power Company Address: 526 S. Church Street, Charlotte NC 28201 -1006


4. (a) Identification of System: NC - Reactor Coolant

3a. Work Order #:

3b. NSM or MM #:

98043860 Repir Organiaq Jd #

N/A


5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda,

(b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989, No Addenda


N/A Code Cases



A 03 Repaired, 03 No 2D Steam Generator B&W 770003 160 N/A 1996 01 Replaced,

RI Replacement ERYes B 0l Repaired, 01 No

03 Replaced,

E0 Replacement 03 Yes C 10 Repaired, 03 No

03 Replaced, E3 Replacement 0 Yes

D 10 Repaired, 03 No 03 Replaced, _3 Replacement 0 Yes

E 03 Repaired, 03 No 03 Replaced, 03 Replacement 03 Yes 03 Repaired, 03 No 03 Replaced, _0 Replacement 0 Yes


Form NIS-2 (Back)


7. Description of Work Replaced stud #2

8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. El Other El Exempto

Pressure _psig Test Temp. - F Pressure _ _ psig Test Temp. F__ F Pressure _ _ psig Test Temp. OF

9. Remarks




Signed ýý" a FL Grass Jr..QA Tech Specialist Date 19 __• "Owner,( Owners Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of --North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period i'i• " to and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection:

Commissions i\)_%77 ýýi, A'SS3', AJT Inspector's %nature National Board, state, Province and Endorsements

Date 9

Page 2 of 2 Rcvision 5

FORM NIS-2 OWNER'S hr-t'ORT FOR REPAIRS OR REPLACEMENTS As Required By The Provlslons Of The ASME Code Section X1



2. Plant Address:

la. Date May 25, 1999

Sheet 1 of 1


12700 i-iaqers Ferry Road, Huntersville, NC 28078

2a. Unit: 01 R12 03 OShared (specify Units

3. Work Performed By: Duke Power Company Address: 526 S. Church Street. Charlotte NC 28201-1006 Type Code Symbol Stamp: N/A Authorization No.. N/A Expiration Date: N/A

4. (a) Identification of System: NI - Safety Injection

3a. Work Order#:

3b. NSM or MM #:

98044201 RertrgnOizfwhoi Job

N/A


5. (a) Applicable Construction Code: ASME Ill 1971 Edition, Summer and Winter Addenda, (b) Applicable Edition of Section XI Utilized for Repairs or Replacements: 1989, No Addenda


N/A Code Cases



A E3 Repaired, o3 No

2NI-0070 Walworth A1344 564 N/A 1976 03 Replaced, I__Replacement IYes

B 0 Repaired, 03 No o Replaced,

__ Replacement 03 Yes C 0 Repaired, 0 No

O3 Replaced, o Replacement 0 Yes

D 0 Repaired, 03 No o3 Replaced,

_0Replacement 0 Yes E 0 Repaired, 0 No

O3 Replaced,

10 Replacement 0 Yes 03 Repaired, 03 No 03 Replaced,

_0 Replacement 03 Yes


Form NIS-2 (Back)


7. Description of Work Replaced Disc

8. Test Conducted:Hydrostatic 51 Pneumatic 51 Nom. Operating Press. 1Z Other 0 Exempts

Pressure _psig Test Temp. OF Pressure j psig Test Temp. _ F Pressure psig Test Temp. OF

9. Remarks

(Applicable Manufacturers Data Records to be attached)



Signed .- ,, FL Grass Jr.,QA Tech Specialist Date 19 q Owner ofOwner's Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut hav 1 inspected the components described in this Owners Report during the period -3to and state that to the best of my knowledge and belief, the Owner has perforrhed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

SCommissions &J% 77 q 7 6 ,q Inspecto S ia re National Board, State Province and Endorsements Date--- 199 " - 9_q

Pagc 2 of 2 Revision 5


1. Owner Address: Duke Power Comipanv


2. Plant Address:

la. Date May11,1999 Sheet 1 of 1



2a. Unit: 0`1 E12 03 []Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #:


Repair Organizeiioý Job #

Type Code Symbol Stamp: N/.A Authorization No. N/A Expiration Date: N/A

4. (a) Identification of System: NV - Chemical and Volume Control

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda,_ (b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989, No Addenda

3b. NSM or MM #:


N/A



. Replacement (yes or no)

A 0 Repaired, 0 No

2NV-14 Walworth A0658 244 N/A 1974 0 Replaced, _ _ Replacement WYes

B 0 Repaired, 0 No o3 Replaced, [3 Replacement 03 Yes

C 0 Repaired, 03 No o3 Replaced, _0 Replacement 0 Yes

D 0 Repaired, 0 No 0 .Replaced, O Replacement 0 Yes

E Repaired, 0 No

o Replaced, _ _ Replacement 0 Yes

F 0 Repaired, 0 No 03 Replaced, _0 Replacement 0 Yes


N/A

Code Cases

Form NIS-2 (Back)


7. Description of Work Replaced 12 body to bonnet studs with 24 nuts

8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. [] Other EJ Exempt[

Pressure _psig Test Temp. OF Pressure psig Test Temp. O__ _F Pressure psig Test Temp. OF

9. Remarks




Signed - , jI, FL Grass Jr.,QA Tech Specialist Date 5 ', 1999 Owner 6r Owners Designee, TMtle

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owners Report during the period to and state that to the best of my knowledge and belief, the Owner has perfor•ed examinations and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

S~~~Commissions&%7 ,7 ad MýM M4- £ Inspecor's SignaCmso Nationai Board, S(ate, Province and'Endorsements

Date 19C79gj


FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI



2. Plant Address:

1 a. Date September 11, 2000

Sheet 1 of 1



2a. Unit: 01 0•2 03 DShared (specify Units .)

3. Work Performed By: Duke Power Compan I' Address: 526 S. Church Street, Charlofte NC 28201-1006


4. (a) Identification of System: NI - Safety Injection

3a. Work Order # :

3b. NSM or MM #:

98220269 Repir Organ=zafe Jcb*

N/A


5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)




A 0 Repaired, 0 No 2-MCR-NI-4556 Duke Power," 14984 N/A N/A N/A OReplaced,

S...._ [ Replacement 03 Yes

B 03 Repaired, []No 2-MCR-NI-4556 Duke Power 21122 N/A N/A N/A 03 Replaced,

__Replacement 03 Yes C 03 Repaired, 0 No

0 Replaced, _0 Replacement 0 Yes

D 10 Repaired, 03 No 0. Replaced,

_3 Replacement 03 Yes E0 Repaired, 0 No 0 Replaced,

E3 Replacement 0 Yes F [0 Repaired, 03 No

0 Replaced,



Form NIS-2 (Back)


7. Description of WorkRenlaced sniihh�r

8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. 01 Other 0 Exemptl9

9. Remarks

Pressure psig Test Temp. OF Pressure _ _ psig Test Temp. OF Pressure psig Test Temp. OF


CERTIFICATE OF COMPUANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the ASME Code, Section XI.


Signed \• • FL Grass Jr.. QA Tech Specialist Date !/!, 2 Owvner,'r Owner's Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of --North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owners Report during the pedod °rQ". to.J:-l l'-06 ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

kAA R.D. KleininspdctoisiSignature

Date .1L _a-o00Commissions

National Board, State, Province and Endorsements


NB7728, NC853. N-1

Renlaced -qni hhpr

FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME!Code Section X1


526 S, Church Street, Charlotte, NC 28201-1006

1 a. Date October 10, 2000 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station t 12700 Hagqers Ferry Road, Huntersville. NC 28078

2a. Unit: 01 02 03 r'Shared (specify Units

3. Work Performed By: Duke Power Comoanv 3a. Work Order#:

Address: 526 S. Church Street, Charlotte NC 28201 -100698243414

Reper Or If Jd$#


4. (a) Identification of System: NC - Reactor Coolant 4. (b)

3b. NSM or MM #:

Class of System: A

N/A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda. N/A Code Cases

(b) Applicable Edition of Section XI Utilized for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)


Column I Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name ol Component Name of Mfg Mfg Serial No. National Board No. Other Identlicati-on Year Built Repaired, Replaced, or ASME Code StampedI


2-NC-VA-0003 Crosby N56925-00-0002 26 N/A 1974 I Replaced, 13 Replacement 0Yes

B 03 Repaired, 03 No 2-NC-VA-0003 Crosby N56925-00-0001 25 N/A 1974 [] Replaced,

.. _ _ _Replacement OYes C 13 Repaired, [] No

03 Replaced, _E Replacement El Yes

D 03 Repaired, 0 No Q Replaced,

[O Replacement [] Yes

E E3 Repaired, 03 No o3 Replaced, _3 Replacement 03 Yes rI D ; r K I

O Replaced, O Replacement 03 Yes


F

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced valve

8. Test Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. 12 Other El Exempto

Pressure 2235 psig Test Temp. 557 OF Pressure ___psig Test Temp. - IF Pressure _ psig Test Temp. _ OF

9. Remarks test was performed per work order 98243956 / 01 under procedure MP/0/A7650/076.




Signed FL Grass Jr., QA Tech Specialist Date -1-0"6 4 OwnerO Owner's Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owners Report during the period - to Ib -/6-00 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, conceming the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

RR.D. Klein Commissions NB7728, NC853, N-I nS r. nature _ D.nalurn-- National Board, State, Province and Endorsements

Date. 10-1 &00,0

'---.


FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASJIVE Code Section XI



2. Plant Address:

la. Date October 12, 2000 Sheet 1 of 1


12700 Haaers Ferry Road. Huntersville, NC 28078

2a. Unit: 01 02 03 OShared (specify Units -

3. Work Performed By: Duke Power Comoany Address: 526 S, Church Street. Charlotte NC 28201-1006

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A.

4. (a) Identification of System: NC • Reactor Coolant

3a. Work Order #: noAA141

Rtemki Ormwfzsio Jeb#

3b. NSM or MM #: N/A


5. (a) Applicable Construction Code: ASMUI 11971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)




A 10 Repaired, 03 No

2A Steam Generator B & W 770002 159 N/A 1996 0 Replaced, 0_ Replacement IYes

B 0 Repaired, 0 No 03 Replaced,

3 0 Replacement 03 Yes C El Repaired, 03 No

03 Replaced,

03 Replacement 03 Yes

D 03 Repaired, 03 No 0, Replaced,

.E3_ Replacement 0 Yes

E 0 Repaired, 0 No 03 Replaced, _3 Replacement 0 Yes

F -0 Repaired, 0 No 03 Replaced, _0 Replacement 0 Yes

Page 1 of2 Revision 7

Form NIS-2 (Back)


7. Description of Work Replaced one primary manway stud (18)

8. Test Conducted:Hydrostatic 5 Pneumatic 5 Nom. Operating Press. R1 Other 0 Exempts

Pressure psig Test Temp. O__ _F Pressure .psig Test Temp. OF Pressure psig Test Temp. F__ F

9. Remarks The test was performed per work order number 98243956 / 01 during the class A walkdown.




Signed S-4 , FL Grass Jr., OA Tech Specialist Date ,., Ownerd& Owner's Designee, Te/

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have Inspected the components described in this Owner's Report during the period _.-.Ca -Q00 to 4:242 -Qg and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owners Report In accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

_R.D. Klein Commissions NB7728, NC853, N-I Inspedtor~ignae National Board, State, Province and Endorsements


Date (-I -.a kooo

FORM NIS-2 OWNER'S REPORT As Required By The Provisio,

REPAIRS OR REPLACEMENTS Ahe ASME Code Section XI

1. Owner Address:

2. Plant Address:

la. Date

Sheet

Duke Power Company


Mcguire Nuclear Station


2a. Unit: " 1 Z 2 [] 3 [] Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order #

Address: 526 S. Church Street. Charlotte, NC 28201-1006 Repai

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #

4. (a) Identification of System: NC 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME m 1971 Edition, Summer and Winter Addenda, N/A Code Cases

(b) Applicable Edition of Section XI Utilizing for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC


98245228/08 r Organization Job #

N/A

and CC and their supports)

Page I of2 Revision 7

10/06/00

1 of I

Column 1 Column 2 Column 3 Column 4 Column 5 Col. 6 Column 7 Column 8 Repaired, ASME Code Name of Component Name of Mfg. Mfg. Serial No. National Other Year Replaced, or Stamped (yes or

Board No. Identification Built Replacement no)

O] Repaired, [] No

A 2MCR-NC-4783 DUKE POWER N/A N/A N/A N/A [ Replaced,

ID Replacement Q Yes [] Repaired, E3 No

B [3 Replaced,

0o Replacement 0 Yes [o Repaired, 0 No

C EO Replaced, 0O Replacement El Yes [o Repaired, 0 No

D [] Replaced, [0 Replacement 0 Yes [o Repaired, 0 No

E [] Replaced,

""O Replacement [0 Yes "O Repaired, 0 No

F [] Replaced,

0] Replacement 0 Yes

Form NIS -2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items I through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of work: Replaced pipe clamp

8. Test Conducted : Hydrostatic [I Pneumatic 0 Nom. Operating Press. 0 Other 0 Exempt 0

Pressure psig Test Temp OF Pressure psig Test Temp OF Pressure psig Test Temp OF

9. Remarks:


CERTIFICATE OF COMPLIANCE We certify that he statements made in the report are correct and this repair or replacement conforms to the rules of the ASME Code, Section XI.

Type Code Symbol Stamp N/A

Certificate of Authorization No. N/A Expiration Date N/A Signed F. R. Sorrow Exec. Supp. Date 10/06 20 00

Owner or Owner's Designee, Title

Page 2 of 2

Rvikx)n 7

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid conmmission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period - to -O-(3 ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Klei ,rL•.. , Commissions NB7728, NC853, N-I Inspector's•'Jgture National Board, State, Province and Endorsei

Date 1. 6 , 20__.,ments

FORM NIS-2 OWNER'S REPOR" As Required By The Provisi,

"REPAIRS OR REPLACEMENTS The ASME Code Section XI

1. Owner Address:

2. Plant Address:

Ia. Date

Sheet

Duke Power Company

526 S. Church Street. Charlotte, NC 28201-1006



2a. Unit: [ 1 ED 2 [1 3 F] Shared (specify units)

3. Work Performed By: Duke Power Company

09/30/00

1 of 1

3a. Work Order # 98312705/01 'PAný6r -- ~nTt-n TM, A4

Address: 526 S. Church Street. Charlotte, NC 28201-1006 -1 .. .... .

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # 11970

4. (a) Identification of System: NI 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME M 1971 Edition, Summer and Winter Addenda, N/A Code Cases

(b) Applicable Edition of Section XI Utilizing for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)


Column 1 Column 2 Column 3 Column 4 Column 5 Col. 6 Column 7 Column 8

Name of Component Name of Mfg. Mfg. Serial No. National Other Year Repaired, ASME Code Board No. Identification Built Replacement no)

o] Repaired, 0] No A 2MCR-NI-4122 DUKE POWER N/A N/A S/N-10404 N/A 0 Repaced,

[] Replaced, [o Replacement El Yes

B 2MCR-NI-4122 DUKE POWER N/A N/A S/N-61224-70 N/A [ Repaired, 0 No o Replaced, ]0 Replacement [3 Yes

C 0 Repaired, 03 No C0 Replaced,

1 0 Replacement 0 Yes D o Repaired, 0 No

D0 Replaced,

EO Replacement 0 Yes E [] Repaired, El No

E Replaced,

D_ Replacement 0l Yes F E Repaired, El No

F0 Replaced,

[] Replacement El Yes

P.ge I of 2 Revision 7

Form NIS -2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used , provided (1) size is 8 1/2 in. x 11 in. (2) information in items I through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of work: Replaced Mech. Snubber with Lesiga HYD.

Snubber

8. Test Conducted: Hydrostatic " Pneumatic 0 Nom. Operating Press. 0 Other 0 Exempt l


9. Remarks:



Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed F. R. Sorrow Exec. Sit Date 09/30 20 00

Owner or Owner s Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period q-1 2-f--O) to 'q-0".,-•) ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Klein Commissions NB7728, NC853, N-I Inspector's Si•a Yure National Board, State, Province and Endorsements

Date •'2C) , 20C"

Page 2 of 2 Rc'qsmon 7


1. Owner Address:

2. Plant Address:

Duke Power Company



1 a. Date September 27, 2000

Sheet 1 of 1

12700 Hagqers Ferry Road, Huntersville, NC 28078

2a. Unit: 01 02 013 r-Shared (specify Units



4. (a) Identification of System: NC - Reactor Coolant

3a. Work Order#: 98314147 Rep*Ir OrganlzazoJob#



5. (a) Applicable Construction Code: ASMEIll 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)



-Replacement (yes or no)

A '0 Repaired, EINo 2-MCR-NC-4288 Duke Power 2443 N/A N/A N/A EIReplaced, 13 Replacement 03 Yes

B 0 Repaired, RINo 2-MCR-NC-4288 Duke Power 2365 N/A N/A N/A 03 Replaced,

RReplacement 03 Yes

C 0 Repaired, 03 No 13 Replaced, _0 Replacement 0 Yes

D 03 Repaired, 0 No

G, Replaced, [] Replacement 0 Yes E 0 Repaired, 0 No

03 Replaced, [0 Replacement 0 Yes 0 Repaired, 0 No 0 Replaced, _0 Replacement 03 Yes


Form NIS-2 (Back)


7. Description of Work Replaced Snubber

8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. 0 Other 0 Exemptlo

Pressure _psig Test Temp. - F Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks




Signed V, FL Grass Jr., QA Tech Specialist Date .4 ' , 2

Owner 9fOwners Designee, Tite


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period to Sle ) to - and state that to the best of my knowledge and belief, the Owner h.s'performed examinations and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, conceming the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection. A .. ' R.D. Klein- Commissions NB7728, NC853, N-I

Inspector's 6ratur National Board, State, Province and Endorsements

Date

FORM NIS-2 OWNER'S r , FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section Xi



2. Plant Address:

la. Date May 19, 1999 Sheet 1 of 1


12700 Haiers Ferry Road, Huntersville, NC 28078

2a. Unit: 01 R12 03 OShared (specify Units

3. Work Performed By: ' Duke Power Company 3a. Work Order#:: Address: 526 S. Church Street, Charlotte NC 28201-1006

97050156Reer Orgwizadon Job#


4. (a) Identification of System: NI -Safety Iniection

5. (a) Applicable Construction Code: ASME-Ill 19Z1 Edition, Summer and Winter Addenda, _ (b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989, No Addenda


3b. NSM or MM #:

4. (b) Class of System: B

N/A

N/A

Code Cases


Replacement (yes or no) A0 E Repaired, 0 No

2NI-14 BWPI 97EP0203 N/A N/A 1997 03 Replaced, IReplacement EIYes B0 Repaired, 0 No

o Replaced, _0 Replacement 0 Yes

C 0 Repaired, 0 No o Replaced, [0 Replacement 0 Yes


E [0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes F0 Repaired, 0 No 0 Replaced, _0 Replacement 0 Yes


Form NIS-2 (Back)



8. Test Conducted:Hydrostatic 0i Pneumatic El Nom. Operating Press. R1 Other El Exemptfl

Pressure psig Test Temp. OF Pressure psig Test Temp. O_ F Pressure psig Test Temp. OF

9. Remarks




Signed \--6.AW Q FL Grass Jr..QA Tech Specialist Date -5-/' 19 9 Owner or'Owner's Designee, Title


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period -- -9q to ,'-o..; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Inpcor _ _a_-_aCommissions Bo7a7qd, 16)a 1 e-!2' aE VsInspector' Sigau National Board, State, Province and Endforsements

Date- 5ýd 199q

FORM NIS-2 OWNER'S i (FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section Xl



2. Plant Address:

la. Date May 19, 1999 Sheet 1 of 1


12700 Haqers Ferry Road. Huntersville, NC 28078

2a. Unit: E1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Companv Address: 526 S. Church Street, Charlotte NC 28201-1006

Type Code Symbol Stamp: N/A Authorization No. NIA Expiration Date: N/A

4. (a) Identification of System: NI - Safety Inlection

3a. Work Order#:

3b. NSM or MM #:

97050160 Repr Organizmon Job #

N/A


5. (a) Applicable Construction Code: ASME III 19Z1 Edition, Summer and Winter Addenda, (b) Applicable Edition of Section XI Utilized for Repairs or Replacements: 1989, No Addenda

N/A Code Cases




A [3 Repaired, 03 No

2N1-18 BWPI 97EP0201 N/A N/A 1997 0 Replaced, OReplacement EYes

B [3 Repaired, 0 No O Replaced, E3 Replacement 0 Yes

C 0 Repaired, 0 No

O Replaced, [] Replacement 03 Yes

D [0 Repaired, 01 No O Replaced,

[] Replacement 0 Yes E 0 Repaired, 0 No

O1 Replaced,

[O Replacement 0 Yes 0 Repaired, 0 No

o Replaced,

0O Replacement 0 Yes


Form NIS-2 (Back)


7. Description of Work Reolaced Disc

8. Test Conducted:Hydrostatic El Pneumatic 0 Nom. Operating Press. I Other El Exempt[]

9. Remarks





Signed FL Grass Jr.,QA Tech Specialist Date - / 19_.91_ Owner,"f Owner's Designee, Tide

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period -3 -a.-91 to 6*-oD-; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissions /\JB--77W A.-, , -- 7 Inspectors igature National Board, State, Province and Endorsements

Date S ? 9I


FORM NIS-2 OWNER'S hi-PORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section Xl



2. Plant Address:

Ia. Date July20, 1999

Sheet 1 of 1


12700 Haaers Ferry Road, Huntersville, NC 28078




4. (a) Identification of System: ND - Residual Heat Removal

3a. Work Order #: 97107046Repair Or zation Jcb #

3b. NSM or MM


#: N/A

5. (a) Applicable Construction Code: ASME Il 11971 Edition, Summer and Winter Addenda, N/A Code Cases fb) Applicable Edition of Section Xi Utilized for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)


Column I Column 2 Column 3 Column 4 Column 6 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Sedal No, National Board No. Other Identification Year Built Repaired, Replaced, or ASME Code Stamped Replacement (yes or no)

A 0 Repaired, 03 No

2ND32 Kerotest KP13-12 7047 N/A 1975 03 Replaced, I_ Replacement IYes

B [ Repaired, 0 No o Replaced, 0_ Replacement 0 Yes

C 0 Repaired, 0 No O Replaced,

o Replacement 03 Yes D 10 Repaired, 0 No

0 Replaced, __ Replacement 0 Yes

E 0 Repaired, 0 No 03 Replaced, 0 Replacement 03 Yes

F 03 Repaired, 0 No 0 Replaced, 13 Replacement 10 Yes


Form NIS-2 (Back)


7. Description of Work Replaced disc and bonnet

8. Test Conducted:Hydrostatic 0l Pneumatic El Nom. Operating Press. [1 Other 0] Exempt[E

Pressure _psig Test Temp. _ F Pressure .psig Test Temp. °F Pressure _psig Test Temp. OF

9. Remarks




Signed -,- 4O) FL Grass Jr.,QA Tech Specialist Date July. 20 1999 "Owner o(:wner's Designee, Title


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period "n'-,3.-.to ýD?- 4 -and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

RgDt Klein Commissions NB7728, NC853. N-I inspect ' iNational Board, State, Province and Endorsements

Date oq

FORM NIS-2 OWNER'S r-rORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section Xl



2. Plant Address:


Sheet 1 of I


12700 Haagers Ferry Road, Huntersville, NC 28078


3. Work Performed By: Duke Power ComDanv Address: 526 S. Church Street, Charlotte NO 28201-1006 Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A

4. (a) Identification of System: CF - Feedwater

3a. Work Order#:

3b. NSM or MM #:Repeir Or IZl Jcb

N/A


5. (a) Applicable Construction Code: ASME Ill 1971 Edition, Summer and Winter Addenda,

(b) Applicable Edition of Section XI Utilized for Repairs or Replacements: 1989, No Addenda


N/A Code Cases

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 • Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Repaired, Replaced, or ASME Code Stamped

Replacement s or no)

A 03 Repaired, 03 No CF Piping Duke Power N/A 61 N/A 1982 [0 Replaced,

EIReplacement EIYes

B 03 Repaired, 03 No 03 Replaced, _0 Replacement 0 Yes 03 Repaired, 03 No 03 Replaced, _3 Replacement 03 Yes

D 13 Repaired, 03 No 03 Replaced, _3 Replacement 03 Yes 0] Repaired, 03 No 03 Replaced, 03 Replacement 03 Yes

F 03 Repaired, 03 No 03 Replaced, __ Replaement 0] Yes


Form NIS-2 (Back)


7. Description of Work Seal welded valve 2CF0188 body to bonnet

8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. IA Other 0 Exempt•l

Pressure _psig Test Temp. OF Pressure psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks




Signed ",, .,• , FL Grass Jr..QA Tech Specialist Date - 19 9jY Owner oi•Owner's Designee, Title


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of. North Carolina and employed by HSBI and I Company of Hartford Connecticut bave inspected thI components described in this Owner's Report during the period L- to , and state that to the best of my knowledge and belief, the Owner has performed examinatiohs and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, conceming the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

S•(• (•P ~ V',.._Commissions KYR77o 9.,n 5 t n VS.e -.7" Inspector'd 8igurue- National Board, StAte, Province and rndorsements

FORM NIS-2 OWNER'S nmr'ORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI



2. Plant Address:

la. Date May20, 1999

Sheet 1 of 1


12700 Haggers Ferry Road, Huntersville, NC 28078

2a. Unit: 01 1•2 03 r3Shared (specify Units



4. (a) Identification of System: NV - Chemical and Volume Control 4. (b)

5. (a) Applicable Construction Code: ASME III 19L1 Edition, Summer and Winter Addenda, (b) Applicable Edition of Section XI Utilized for Repairs or Replacements: 1989, No Addenda


3a. Work Order #:

3b. NSM or MM #:

98024727 Repi OrMazone Job #

N/A

Class of System: B

N/A Code Cases




2NV0124 Fisher 5921347 741 N/A 1975 O3Replaced, ,.__ _Replacement EYes

B 0 Repaired, 03 No

03 Replaced, _ __Replacement O3Yes

C [0 Repaired, 03 No 0 Replaced,

__3 [] Replacement 03 Yes D 10 Repaired, 0 No

0] Replaced,

[0 Replacement 0 Yes E 13 Repaired, 01 No


LI- riepa'•,J ,'LI I'IOri--tigpalredo, 0 Replaced,

0 Replacement 0 Yes


F

Form NIS-2 (Back)


7. Description of Work Replaced Plug

8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. l0 Other 51 Exempts

Pressure _psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. -OF

9. Remarks




Signed FL Grass Jr.,QA Tech Specialist Date t.w, 19 iL Owner orOwne's Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owners Report during the period 3 a! to 5"-94 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Nationa oard Commissions M-7-7 a2? M)and3. N -7m Inspector's Signatdr) - National Board, Stale, Province and Enaorsements


Date 1~2 I 194

FORM NIS-2 OWNER'S F-iEPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Secton X1



2. Plant Address:

la. Date April 29, 1999 Sheet 1 of 1



2a. Unit: 01 E12 103 []Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #:




5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda,



3b. NSM or MM #:

Class of System: B N/A

98024747 R•er Organiz&oi Jolb#

N/A

Code Cases

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8

Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Repaired, Replaced, or ASME Code Stamped Replacement (yes or no)

A 0 Repaired, 03 No

2NV-1 1 Walworth 2318SP A0598 N/A 1973 0 Replaced, ElReplacement 0Yes

B 0 Repaired, 03 No O3 Replaced, 1o Replacement 03 Yes

C [0 Repaired, [3 No o3 Replaced, Eo Replacement E3 Yes rI ;I-A I,-

0 Replaced, 0] Reolacement 03 Yes

_________________la e * I ..0 Repaired, O Replaced, 0 Replacement

4 1 I I � I LI fl�p�II�U, LI PIV

0 Replaced, O ReDlacement

13 Yes

0] YesII I__ _ __ _ _ .- I7L_ __ _ _


E

F

N/A

Form NIS-2 (Back)


7. Description of WorkPin neiorlo hrnnnatt hnlf,- annt f M "U~% ,rjS ,JL, A 0 L.

8. Test Conducted:Hydrostatic 0 Pneumatic El Nom. Operating Press.

9. Remarks

Z] Other El Exempt[]

Pressure psig Test Temp. _ F Pressure psig Test Temp. OF Pressure psig Test Temp. OF




Signed N• C4/- FL Grass Jr.,QA Tech Specialist Date 19 2Ownetror Owner's Designee, Title


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut haveinspected the mponents described in this Owner's Report during the period ..- "- to -TZ-!=1; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissions A) 7 •A! S ' J Inspectors Si _ l National Board, State, Province and Endorsements

Date

FORM NIS-2 OWNER'S r-PORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section Xi



2. Plant Address:

la. Date May26.,1999

Sheet 1 of 1

McGuire Nuclear Station,

12700 Hapers Ferry Road, Huntersville, NC 28078

2a. Unit: 01 219 1-3 OShared (specify Units

3. Work Performed By: Duke Power Company Address: 526 S. Church Street, Charlotte NC 28201-1006 Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A

4. (a) Identification of System: CF- Feedwater

5. (a) Applicable Construction Code: ASME IIl 1971 Edition, Summer and Winter Addenda, (b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989, No Addenda


3a. Work Order #:

3b. NSM or MM #:


N/A

98025055 Repair Organizaion Job#

N/A

Code Cases



A 03 Repaired, 03 No 2CF-0190 Kerotest DAN1-8 31242 N/A 1980 03 Replaced,

I EIReplacement IBYes B 0 Repaired, E3 No

0 Replaced, 10 Replacement 03 Yes

C 0 Repaired, 03 No 0 Replaced, _0 Replacement 0 Yes

D 0 Repaired, 0 No 0 Replaced,



F 0 Repaired, 0 No 0 Replaced,

__ Replacement 0 Yes


Form NIS-2 (Back)


7. Description of Work Seal welded Body to bonnet

8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. Rl Other [] Exemptl

Pressure _psig Test Temp. O__ _F Pressure psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks




Signed ,M/_ FL Grass Jr.,QA Tech Specialist Date ,z•/Z1 19_._2 "bwner o )•ner's Designee, Titoe

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticu have inspected the components described in this Owners Report during the period 3---.-Rq to S and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

totur Commissions AY1V7-WA J~ iC-~ On /J 17T ate 9r Ia~onal Board, State, Province andEndorsements Date



1. Owner Address:

2. Plant Address:

Duke Power Company




Ia. Date 4/1/99

Sheet 1 of I

2a. Unit: [I 1 ] 2 [- 3 E] Shared (specify units)

3. Work Performed By: Duke Power Company

Address: 526 S. Church Street, Charlotte, NC 28201-1006


(a) Identification of System: NV 4. (t

(a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda,

Applicable Edition of Section XI Utilizing for Repairs or Replacements: 1989, No Addenda

Identification of Components Repaired or Replaced and Replacement Components:

3a. Work Order # 98043826 Repair Organization Job #

3b. NSM or MM # N/A

) Class of System: B

NO Code Cases

Column 1 Column 2 Column 3 Column 4 Column 5 Col. 6 Column 7 Column 8 Repaired, Replaced, or ASME Code

Name of Component Name of Mfg. Mfg. Serial No. National Board No. Other Identification Year Built Replacement Stamped (yes or no) __________________Repair et tmeddyes N o ro

A Hanger DUKE POWER CO NA NA LOAD PIN NA E3 Repaired, 0 No 0 Replaced,

2-MCR-NV-4483 3/8" DIA [] Replacement 0 Yes

B HANGER DUKE POWER CO NA NA LOAD PIN NA 0 Repaired, 0 No 0 Replaced,

2-MCR-NV-4483 3/8" DIA 0 Replacement E0 Yes C ] Repaired, 0 No o[ Replaced,

[3 Replacement E3 Yes D 0 Repaired,' 0 No

[o Replaced, EO Replacement " [ Yes

o] Repaired, 0 No E E Replaced,

[o Replacement 0 Yes [] Repaired, 0 No

F [3 Replaced, E3 Replacement 0 Yes

Page I of 2 Revixion 5

4.

5.

(b)

6.

Form NIS -2 (Back)


7. Description of work : Replaced load pin

8. Test Conducted : Hydrostatic [] Pneumatic 0 Nom. Operating Press. [I Other [I Exempt 0

Pressure Pressure Pressure

psig psig psig

Test Temp

Test Temp

Test Temp

OF

OF OF

9. Remarks : No testing required, snubber operability was not affected


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Providence of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period --- [ to.1-&.1." L ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Inspector' Signature

Date 1'6 ,1s_

Commissions . 77,,,S J -IZ National Board, State, Providence and Endorsements


Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed A4WI'Vla ./?!16:WV• , '-Date 4/1 19 99

Ownei or Owner's Designee,"litle

Pape 2 of 2 Revision 5


1. Owner Address:

2. Plant Address:

Duke Power Company



12700 Hagers Fry Road, Huntersville, NC 28078

Ia. Date 4/28/99

Sheet 1 of

Unit: []1 ] 2 [] 3 [] Shared (specify units)

Work Performed By: Duke Power Company 3a. Work Order 4


Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM

(a) Identification of System: CA 4. (b) Class of System: B

(a) Applicable Construction Code: ASME 1111971 Edition, Summer and Winter Addenda, NO Code Cases

Applicable Edition of Section XI Utilizing for Repairs or Replacements: 1989, No Addenda

Identification of Components Repaired or Replaced and Replacement Components:

98043826 Repair Organization Job #

# N/A


2a.

3.

4.

5.

(b)

6.


Name of Component Name of Mfg. Mfg. Serial No. National Board No. Other Identification Year Built Replacement Stamped (yes or no)

A Hanger DUKE POWER CO NA NA LOAD PIN NA '] Repaired, 0 No 0 Replaced,

2-MCA-CA-H089 3/4" DIA [3 Replacement 0l Yes

B HANGER DUKE POWER CO NA NA LOAD PIN NA [3 Repaired, 0 No [3 Replaced,

2-MCA-CA-H089 3/4" DIA [] Replacement [3 Yes O[ Repaired, 0l No

C [3 Replaced,

1 o Replacement 0l Yes O[ Repaired, 0l No

D 0l Replaced, [o Replacement 0l Yes 0 Repaired, 0l No

E [3 Replaced, 1 [3 Replacement El Yes

O Repaired, 0l No F E Replaced, )

I r-_ Replacement 0l Yes

Form NIS -2 (Back) NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used , provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of work: Replaced load pin

8. Test Conducted : Hydrostatic 0 Pneumatic 0 Nom. Operating Press. 0 Other 0 Exempt 0





Type Code Symbol Stamp N/A Certificate of Authorizatio J/o. N/A Expiration Date N/A Signed / L el•' /Ž' (" "•1 ý5'i#•C'41 5 'Date 4/28 19 99


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Providence of North Carolina and employed by HSBI and I Company ofHartford onncticut havei spc the components described in this Owner's Report during the d ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissions /) 7 A ' ?• / ) .K InD tor'-Signature National Board, State, Providence and Endorsernents Date - 6 , 1929

Page 2 o"2 Revision 5

FORM NIS-2 OWNER'S htM-ORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. Owner Address:

2. Plant Address:


Sheet 1 of 1

Duke Power Company



12700 Ha-ers Ferry Road, Huntersville, NC 28078

2a. Unit: 01 12 03 O3Shared (specify Units . _.

3. Work Performed By: Duke Power Company 3a. Work Order #: 98071681 Address: 526 S. Church Street, Charlotte NC 28201-1006 Regr OWaion Job

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: MGMM104

4. (a) Identification of System: RV - Containment Ventilation Cooling Water 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 19Z1 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989, No Addenda


.05

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Seda] No. National Board No. Other Identification Year Built Repaired, Replaced, or ASME Code Stamped


RV Piping Duke Power N/A 72 N/A 1982 OReplaced, _ Replacement ElYes

B 03 Repaired, 13 No o3 Replaced, _Replacement OYes

C 0 Repaired, 03 No El Replaced, 1o Replacement El Yes

D 0 Repaired, 13 No El Replaced, E3 Replacement 0 Yes 03 Repaired, 13 No El Replaced, EO Replacement El Yes

-In Q I I u

"0 Replaced, "0 Replacement 13 Yes


Form NIS-2 (Back)


7. Description of Work Replaced bolting in flange at Valve 2RV32A.

8. Test Conducted:Hydrostatic [] Pneumatic 0 Nom. Operating Press. 01 Other 0 Exempt[

Pressure psig Test Temp. -OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks




Signed ,, FL Grass Jr..QA Tech Specialist Date 19 19 Owner or Owner's Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have in p~cted the components described in this Owners Report during the pedod -4 toS"-J.--'q and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

nso r NaCommissions aO BIor S1Z tA en, o in) a1 Inspefto s Hrgn~iture National Board, State,'Province and 1fridorsernents


Date . 19

FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section X!

1. Owner Address:

2. Plant Address:

2a. Unit: E1 02

1a. Date May 20, 1999

Sheet 1 of 1Duke Power Company



12700 Haaers Ferry Road, Huntersville. NC 28078

03 O-Shared (specify Units

3. Work Performed By: Duke Power Company Address: 526 S. Church Street, Charlotte NC 28201 -1006


4. (a) Identification of System: RV - Containment Ventilation Cooling Water

3a. Work Order # :

3b. NSM or MM #:


5. (a) Applicable Construction Code: ASME 1II 1971 Edition, Summer and Winter Addenda, (b) Applicable Edition of Section XI Utilized for Repairs or Replacements: 1989, No Addenda


N/A Code Cases



RV Piping Duke Power N/A 72 N/A 1982 O3Replaced, __Replacement I0Yes

B 03 Repaired, 03 No o3 Replaced,

[]Replacement DYes C 03 Repaired, 0 No

o Replaced,

13 Replacement 0 Yes D 0 Repaired, 0 No


E 0 Repaired, 0 No 0 Replaced,


RI epaired, 03 Replaced, 03 Replacement

0YNO

13 Yes

Page l of2 Revision 5

98071683Replr OqwaizaWlon Jcb#

MGMM1 0405

F

Form NIS-2 (Back)


7. Description of Work Replaced bolting in flange at Valve 2RV33B.

8. Test Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exempto

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks


CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the ASME Code, Section X1.


Signed FL Grass Jr.,QA Tech Specialist Date 19 .;Eo1

"Owner c1 Owner's Designee, Title


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have ins•ected the components described in this Owner's Report during the period 3A:2ýS% to §ý"---9 : and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, conceming the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

n'po aCommissions M '77• , L7,3C ) J -- ? nspec or sNational Board, State, Province and Endorsements

Date 1 9_j


1. Owner Address:

2. Plant Address:

Duke Power Company



1 a. Date May 20, 1999

Sheet 1 of 1



3. Work Performed By: Duke Power Company Address: 526 S, Church Street, Charlotte NC 28201-1006

Type Code Symbol Stamp: N/_A Authorization No. N/A Expiration Date: N/A

4. (a) Identification of System: RV - Containment Ventilation Cooling Water

3a. Work Order#:

3b. NSM or MM #:

98071686 Repair OMwkellw Job #

MGMM10405


5. (a) Applicable Construction Code: ASME 1II 1971 Edition, Summer and Winter Addenda, (b) Applicable Edition of Section Xi Utilized for Repairs or Replacements: 1989, No Addenda


N/A Code Cases


Replacement (yes or no) A E3 Repaired, 03 No

RV Piping Duke Power N/A 72 N/A 1982 nReplaced, .__ _ _ _I .Replacement OYes

B 03 Repaired, 03 No 03 Replaced, nReplacement DYes

C 0 Repaired, 0 No o Replaced, O Replacement 0 Yes

D 0 Repaired, 0 No 0 Replaced, 0 Replacement 03 Yes

E 0 Repaired, 0 No o Replaced, [0 Replacement 03 Yes

R -epaired, 03 Replaced, 03 Replacement

U NO

0 Yes


F

Form NIS-2 (Back)


7. Description of Work Replaced bolting in flange at Valve 2RV76A.

8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. IA Other 0 Exempt[

Pressure psig Test Temp. OF Pressure __ _psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks




Signed \,• _ FL Grass Jr..QA Tech Specialist Date .Ž•-Q, 19 99_ Owner or Owners Designee, ride

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have ins ed the components described in this Owners Report during the period 9to , and state that to the best of my knowledge and belief, the Owner has performdd examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section X1. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

'Jrg~ture Commissions -177W ,M SS tJ --T InsPctors &gtkturG National Board, State, Province andFEndorsements


Date 1.9(1




2. Plant Address:


Sheet 1 of I


12700 Hagers Ferry Road. Huntersville. NC 28078




3a. Work Order#:

3b. NSM orMM

98071687Reer Organiai Job#

PAt_-A AA,4 A A.r

4. (a) Identification of System: RV - Containment Ventilation Cooling Water 4. (b)

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, _ (b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989. No Addenda

Class of System: B

N/A




A 03 Repaired, 03 No RV Piping Duke Power N/A 72 N/A 1982 OReplaced,

"I _Replacement EYes 0E Repaired, 03 No 03 Replaced,

OReplacement OYes C 03 Repaired, 0 No

o3 Replaced,

E0 Replacement 03 Yes D 0 Repaired, 0 No

0 Replaced, 13 Replacement 03 Yes

E 0 Repaired, 0 No 0 Replaced, 1_ Replacement 0 Yes

"LI Repaired, "0 Replaced, 0 Replacement

LI No

0 Yes


Code Cases

F

0

Form NIS-2 (Back)


7. Description of Work Replaced bolting in flange at Valve 2RV77B.

8. Test Conducted:Hydrostatic 0] Pneumatic 0 Nom. Operating Press. IA Other 0 Exempt[]

Pressure psig Test Temp. OF Pressure psig Test Temp. F__ F Pressure _psig Test Temp. OF

9. Remarks




Signed \ FL Grass Jr..QA Tech Specialist Date .S-,' 19 .2_ "Owner of'Owner's Designee, Tite

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period -'o -j to" and state that to the best of my knowledge and belief, the Owner has performed examinations find taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or pro rt damage or a loss of any kind arising from or connected with this inspection.

-- _ _ __ Commissions 0- '7T7 9 W ',- A) -. 7 Inspector's S gnatufeo National Board, State, Province and Endorsements


Date l


1. Owner Address:

2. Plant Address:

2a.

3.

1 a. Date 09-23-00

Sheet 1 of I

Duke Power Company




Unit: El1 2 2 [] 3 El Shared (specify units)

Work Performed By: Duke Power Companv 3a. Work Order # 98071897-08 Repair Organization Job #


Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM# MGMM10177

4. (a) Identification of System: FW REFUELING WATER 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME m 1971 Edition, Summer and Winter Addenda, N-416-1 Code Cases




Column 1 Column 2 Column 3 Column 4 Column 5 Col. 6 Column 7 Column 8 Repaired, Replaced, or ASME Code Name of Component Name of Mfg. Mfg. Serial No. National Board No. Other Identification Year Built Replacement Stamped C(es or no)

0] Repaired, 0] No A VALVE 2FW 009 WALWORTH A1116 316 2FW 1974 [3 Replaced,

[3 Replacement 0 Yes 0] Repaired, 0] No

B VALVE 2FW 075 ITT GRINNELL 80-52815-1-8 WR6321 2FW 1980 [3 Replaced,

________________ ___________[3 Replacemet, e 0 Replacement 0 Yes

C PIPING DUKE POWER N/A 54 2FW 1982 [] Repaired, 0 No [3 Replaced,

M] Replacement 0 Yes [I Repaired,. 0 No

D [ Replaced, [3 Replacement [3 Yes [0 Repaired, E3 No

E [ Replaced, ----- 1-[o Replacement [3 Yes

E3 Repaired, [3 No F 0 Replaced,

[o Replacement 0 Yes

Form NIS -2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of work: DELETED VALVE 2FW 009 & INSTALL VALVE

2FW 75 & PIPING

8. Test Conducted : Hydrostatic D Pneumatic D Nom. Operating Press. 0 Other 0 Exempt 0

Pressure HEAD psig Test Temp 81.9 OF Pressure psig Test Temp OF Pressure psig Test Temp OF

9. Remarks:



Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed E. P. Robinson Exec. Supp. 0, Date 09-28 20 00


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut h veinspected the components described in this Owner's Report during the period _ to, 8-111M ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Klein S Commissions NB7728, NC853, N-I Inspector s~ National Board, State, Province and Endorsements

Date f-, .• , 20 C)(2>





2. Plant Address:


Sheet 1 of 1



2a. Unit: 01 I02 03 OShared (specify Units

3. Work Performed By: Duke Power Company Address: 526 S. Church Street, Charlotte NC 28201-1006 Type Code Symbol Stamp: N/A Authorization No. N/._A Expiration Date: N/A

4. (a) Identification of System: SM - Main Steam

5. (a) Applicable Construction Code: ASME Il 1971 Edition, Summer and Winter Addenda, (b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989, No Addenda


3a. Work Order #:

3b. NSM or MM #:


N/A

98090072 Repat OrWizubw Jcb#

N/A

Code Cases



2SM-0101 Kerotest TM5-5 12302 N/A 1996 OReplaced, __Replacement 0Yes

B 13 Repaired, 03 No o3 Replaced, [0Replacement DYes

C 13 Repaired, 03 No

03 Replaced, _ Replacement 03 Yes

D 10 Repaired, 0 No 0 Replaced, 10 Replacement 0] Yes

E E0 Repaired, 0 No 0 Replaced,


u Repaired, 03 Replaced, 03 Replacement

Li NO

0 Yes


F

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items1l through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.


8. Test Conducted:Hydrostatic Li Pneumatic EJ Nom. Operating Press. Rl Other El ExemptEi

Pressure _psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks


CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the ASME Code, Section X1.


Signed !;.aog6/ FL Grass Jr.,QA Tech Specialist Date 19 9q Owner lOwner's Designee, Title


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owners Report during the period 3-0--qt to ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissionsar Inspector's i nre National Board, State, Province and Endorsements

DateJS VA6 19T

2. Plant Address:

-....... V wei %mrnpany

526 S. Church Street, Charlotte. NC 28201-1006



Ia. Date 10-01-00

Sheet 1 of I

2a. Unit: [-1 ] 2 [1 3 El Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order # 98098695-58

Address: 526 S. Church Street. Charlotte. NC 28201-1006 Repi orgn.nti, Job


4. (a) Identification of System: NI (SAFETY INJECTION) 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME I 1921 Edition, Summer and Winter Addenda, N-416-1 Code Cases



.. . Column 1 Column 2 Column 3 Column 4 Column 5 Col. 6 Column 7 Column 8 Repaired, Replaced, or ASME Code Name of Component Name of Mfg. Mfg. Serial No. National Board No. Other Identification Year Built Replacement Stamped (yes or no)

A 2NI VALVE 9A WALWORTH C54751 2 NI 1973 [0 Repaired, 03 No 0 Replaced,

_..... ......... .C3 Replacement 0 Yes

B 2NI VALVE 9A BWIP E492A-l-3 2102 NI 1998 [0 Repaired, 0 No [3 Replaced,

S........ .0 Replacement 0 Yes C 0 Repaired, 0 No

[3 Replaced, I...... ... [I Replacement [0 Yes

D [o Repaired, 0 No D-0 Replaced,

__........___0 Replacement 0 Yes E [0 Repaired, 0 No E3 Replaced,

S•.___ Replacement 0 Yes F [o Repaired, [3 No F0 Replaced,

0O Replacement 0 Yes


3

.0 < Z c r '

\ __u~ r'0A-]

FORM NPV-1 CERTIFICATE HOLDERS' DATA REPORT FOR NUCLEAR PUMPS OR VALVES. 7 As Required by the Provisions of the ASME Code, Section III, Division 1 e ,

Pg. of

"8W/IP International, Inc. Valve Division -- eet

1. Manufactured and certified by 701 First Street, Williamsport, PA. 17701 jname and address of N Certificate Holder)

2. Manufacturedfor Duke Energy Corporati.on P.O. Box 1015, Charlotte, NC. 28201-115 (name a address of Puechasee) 2........ .... 8-89"

McGuire Nuclear Site, 13225 Hagers Ferry Rd. Highway 73, Huntersville, NC. 3. Location of installation Iname and address

Flex Wedge Gate W9825122 Rev. B _ N/A t. Model No.. Series No.. or Type Drawing Rev. CRN_

;. ASME Code, Section Wit, Division 1: 1989 1990 2 N/A leditiont (addenda datel (classl (Code Case no.) Va 1ve 4 4

Pump or valve Valve Nominal inlet size -- Outlet size (in.) (in.)

Material: Body SA351-CF8M Bonnet SA_82-F316 Disk SA351-CFBM g• . NIA

(a) Cert.

Holder's

Serial No.

'92A-1-3 .92A-l-4

1b) Nat'l

Board

No.

NB# 2102 NB# 2103

Ic) Body Serial No.

Y1172 Y1174

(d) Bonnet

Serial No.

3 4

(el Disk

Serial No.

3

emental information in form of lists. sketches, or dcawings may be used provided (II size is 8 % x 11, (2) information in items I through 4

a Data Report is included on each sheet. (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

This form I00037) may be obtained from the Order Dept.. ASME. 22 Law Drive. Box 2300. Fairfield, NJ 07007-2300. 1EPFI.4T 693

12 ,,7


1. Owner Address:

2. Plant Address:

la. Date 05/20/99




12700 Hagers Ferr Road, Huntersville. NC 28078

2a. Unit: F] 1 0 2 0l 3 E] Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order A

Address: 526 S. Church Street. Charlotte, NC 28201-1006

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM

4. (a) Identification of System: NV 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME MI 1921 Edition, Summer and Winter Addenda, N/A Code Cases

(b) Applicable Edition of Section XI Utilizing for Repairs or Replacements: 1989, No Addenda


98103158 Repair Organization lob#

# N/A


Name of Component Name of Mfg. Mfg. Serial No. National Board No. Other Identification Year Built Replacement Stamped (yes or no) 198 Repaired, 0 No

A VALVE DRESSER TE09057 415 2NV-486 1978 0 Repaed, [] Replaced,

__ Replacement M Yes

o3 Repaired, [3 No B 0 Replaced,

[o Replacement 0 Yes [I Repaired, 0 No

C 0 Replaced, 0] Replacement 0 Yes [o Repaired, 0 No

D 0 Replaced, _ _ Replacement _0 Yes o Repaired, 0 No

E 0 Replaced, 0 Replacement 0 Yes

o Repaired, 0 No

F 0 Replaced, o Replacement 0 Yes


Form NIS -2 (Back)


7. Description of work: REPLACED DISC

8. Test Conducted : Hydrostatic 0 Pneumatic [0


,psig

psig psig

Nonm Operating Press. 0 Other 0 Exempt 0

Test Temp Test Temp Test Temp



Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed F.R. Sorrow Exec. Supp. y Date 05/20 19 99

Owner or Owner's D•signee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Providence of North Carolina and employed by HSBI and I Company of Hartford Connecticut have ins pcted the components described in this Owner's Report during the period -,b to'; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Klein QU Inspector's Sign ure

Date I , 19-9_1

Commissions NB7728, NC853, N-I National Board, State, Province and Endorsements


9. Remarks :

OF OF OF


1. Owner Address:

2. Plant Address:

I a. Date July 6. 2000 Sheet 1 of 1

Duke Power Company




2a. Unit: 01 212 03 O-Shared (specify Units )




3a. Work Order #:

3b. NSM or MM #:

98107296 Re~r Orgkafion Job*

N/A


5. (a) Applicable Construction Code: ASMEIII 1971 Edition, Summer and Winter Addenda, N/A Code Cases

(b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)



Replacement s or no) A 10 Repaired, 03 No

2NV-265 Kerotest DG5-1 1 5879 N/A 1981 03 Replaced, iReplacement WYes

B 03 Repaired, 0 No 03 Replaced, [0 Replacement 0 Yes

0 Repaired, 03 No 0 Replaced,





__ Replacement 0 Yes


Form NIS-2 (Back)


7. Description of WorkRim ntlsOHrld icr

8. Test Conductedl--Hydrostatic 0 Pneumatic 0 Nom. Operating Press. AOther 0 Exempto

9. Remarks

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure -psig Test Temp. OF

(Applicable Manufacturers Data Records.to be attached)

CER7IFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the ASME Code, Section Xl.


Signed .i,-. ) FL Grass Jr.. QA Tech Specialist Date 7 / , '

Owner o(Owners Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owners Report during the period Yt- to 4•-L 1, and state that to the best of my knowledge and belief, the Owner has p4drirel examinations and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, conceming the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

- '_4 t ,- R.D. Klein Inspec nature

Date ao



R•nln•rl rlic=n




2. Plant Address:

la. Date May25. 1999

Sheet 1 of 1



2a. Unit: 01 02 03 []Shared (specify Units

3. Work Performed By: Duke Power Company Address: 526 S. Church Street. Charlotte NC 28201-1006 Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A


3a. Work Order #:

3b. NSM or MM #:

98122733 Repair Owanizaion Job#

N/A


5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, (b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989, No Addenda


N/A Code Cases



2ND-0008 Borg - Warner 4625 39 N/A 1975 03 Replaced, _ _...._IOReplacement 0Yes

B 03 Repaired, 03 No 03 Replaced, E3 Replacement 03 Yes

03 Repaired, 03 No 03 Replaced, 03 Replacement 03 Yes

D 13 Repaired, 03 No 03 Replaced, _0 Replacement 03 Yes 03 Repaired, 03 No 03 Replaced, _0 Replacement 03 Yes 0 0 Repaired, 03 No 03 Replaced, _0 Replacement 0 Yes


Form NIS-2 (Back)


7. Description of Work Replaced Disc Assembly

8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. El Other I] Exempti


9. Remarks




Signed Lý& Q FL Grass Jr.,QA Tech Specialist Date -5 4, 19 •' Owner d(Owner's Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspectedth components described in this Owners Report during the period t ( to" ---c,: and state that to the best of my knowledge and belief, the Owner has performned examinatiob's and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

-•Commissions "77 A -i Inspei•t r SComminjure National Board, State, Province and Endorsements


Date 1W1 9_._1

FORM NIS-2 OWNER'S h,-r-ORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section Xl



2. Plant Address:

la. Date May 25,.1999 Sheet 1 of 1


12700 Haagers Ferry Road, Huntersville, NC 28078


3. Work Performed By: Duke Power Company Address: 526 S. Church Street. Charlotte NC 28201-1006 Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A

4. (a) Identification of System: VI - Instrument Air

3a. Work Order #: 98142870Rep& Oraqazao Job #

3b. NSM or MM#: N/A


5. (a) Applicable Construction Code: ASME 1111971 Edition, Summer and Winter Addenda, (b) Applicable Edition of Section XI Utilized for Repairs or Replacements: 1989, No Addenda


N/A Code Cases



A E3 Repaired, 03 No

2VI-0040 Kerotest S20-12 N/A N/A 1973 03 Replaced,

1 I•Replacement E[Yes

B 03 Repaired, 03 No O Replaced, 13 Replacement 03 Yes

-C 0 Repaired, 03 No [] Replaced,

o3 Replacement 03 Yes D O Repaired, 03 No

O3 Replaced,

1o Replacement 0 Yes

"El Replaced, "0 ReDlacement

I__ _ _ _ __ _. I i I U I'JIu iepalrea, "0 Replaced,

"0 Replacement

U YNe

13 Yes

0 Yes


E

Form NIS-2 (Back)



8. Test Conducted:Hydrostatic 0 Pneumatic 51 Nom. Operating Press. I£ Other 0 ExemptE

Pressure _psig Test Temp. F__ F Pressure _psig Test Temp. _ F__F Pressure _psig Test Temp. OF

9. Remarks



Type Code Symbol Stamp NIA Certificate of Authorization No. N/A Expiration Date N/A

Signed -•- , FL Grass Jr.,QA Tech Specialist Date , ;• 19 I__j Owner opner's Designee, TtMee


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period •-•-' to ; and state that to the best of my knowledge and belief, the Owner has performed examinatiofs and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

______ ,__, _ Commissions FCB7• ., _, - /SJ- l Insaecto,.' S I , 1a.re National Board, State, Province and Endorsements

Date._. 1997

FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XA



2. Plant Address:

la. Date May20,1999 Sheet I of 1


12700 Haqers Ferry Road, Huntersville, NC 28078

2a. Unit: 01 1212 03 [Shared (specify Units

3. Work Performed By: Duke Power Company Address: 526 S. Church Street. Charlotte NC 28201-1006



5. (a) Applicable Construction Code: ASME 1111971 Edition, Summer and Winter Addenda,



3a. Work Order #:

3b. NSM or MM #:

98143386 RqeptOrganizason Jab#

N/A

Class of System: B

NIA Code Cases


, Replacement (yes or no)

A 03 Repaired, 03 No 2NV238 Fisher 5921349 790 N/A 1976 E3Replaced,

1_EReplacement EYes

B 03 Repaired, 03 No 03 Replaced, [0Replacement WYes

C [0 Repaired, 03 No 0 Replaced, 03 Replacement 03 Yes

D 0 Repaired, 0 No [0 Replaced, 0 Replacement 03 Yes

E 0 Repaired, 0 No 0 Replaced, [0 Replacement 0 Yes 03 Repaired, 03 No"0 Replaced, "0 Replacement 01 Yes


r

Form NIS-2 (Back)



8. Test Conducted:Hydrostatic El Pneumatic 0 Nom. Operating Press. IA(ther El Exempto

Pressure psig Test Temp. OF Pressure - psig Test Temp. OF Pressure _ _ psig Test Temp. OF

9. Remarks




Signed -A FL Grass Jr.,QA Tech Spialist Date 19 Owner o(Owner's Designee, Tie


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have insp eWted the components described in this Owners Report during the pedod- to . and state that to the best of my knowledge and belief, the Owner has performd examination' and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

tor N e 04Commissions '"717 , MC Y.3, /0 T Inspector'Signet0National Board, State,4 Province and Enddrsements

DateS



2. Plant Address:



Ia. Date July 6, 2000

Sheet 1 of 1

12700 Hacters Ferry Road, Huntersville, NC 28078




4. (a) Identification of System: VI - Instrument Air

3a. Work Order #:

3b. NSM or MM #:


98145459 RepairOwantzadon Jcb#

N/A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)





2V1-124 Kerotest $20-9 N/A N/A 1973 03 Replaced, IReplacement WYes

B 03 Repaired, 0 No 0 Replaced, 03 Replacement 03 Yes

3 0 Repaired, 03 No 03 Replaced, _0 Replacement 03 Yes

D 0 Repaired, 0 No

0 Replaced, 3 0Replacement 03 Yes

E 0 Repaired, 03 No 0 Replaced, _0 Replacement 0 Yes 03 Repaired, 0 No 03 Replaced,



Form NIS-2 (Back)



8. Test Conducted:Hydrostatic 0 Pneumatic EJ Nom. Operating Press. lBOther 0 ExemptO

Pressure psig Test Temp. °F Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks




Signed FL Grass Jr., QA Tech Specialist Date ____

"Owner orDwner's Designee, Tie

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owners Report during the period1: .. to "--J- . and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R.D. Klein Commissions NB7728. NC853, N-I " "gnata r National Board, State, Province and Endorsements

Date • 4~s ,



1. Owner Address:

2. Plant Address:

la. Date 4/1/1999

Sheet 1 of I

Duke Power Company




2a. Unit: ] 1 Z 2 E] 3 [] Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order # 98146480 Repair Organization Job#


Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # N/A


5. (a) Applicable Construction Code: ASME 11 1971 Edition, Summer and Winter Addenda, NO Code Cases

(b) Applicable Edition of Section XI Utilizing for Repairs or Replacements: 1989, No Addenda


Column I Column 2 Column 3 Column 4 Column 5 Col. 6 Column 7 Column 8 Repaired, Replaced, or ASME Code

Name of Component Name of Mfg. Mfg. Serial No. National Board No. Other Identification Year Built Replacement Stamped (yes or no) Hanger DUKE POWER CO NA NA LOAD PIN NA 0 Repaired, 0 No

g0 Replaced,

2-MCR-NV-4470 3/4" DIA 0[ Replacement 0 Yes 0] Repaired, [] No

B HANGER DUKE POWER CO NA NA LOAD PIN NA. [ Replaced,

2-MCR.NV-4470 3/4" DIA _0 Replacement 0 Yes 0[ Repaired, 0 No C0 Replaced, [O Replacement 0 Yes

0 Repaired, D No

D ]0 Replaced, 0] Replacement 0 Yes

o[ Repaired, 0 No E 0" Replaced,

""o Replacement 0 Yes o] Repaired, [0 No

F 0[ Replaced, 1 [o Replacement 10 Yes


Form NIS -2 (Back)


7. -Description of work: Replaced load pin

8. Test Conducted : Hydrostatic [] Pneumatic 0 Nom. Operating Press. 0 Other [I Exempt 0

Pressure psig Pressure psig Pressure psig

Test Temp

Test Temp

Test Temp

OF

OF OF




Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed A~ g Date 4/1 19 99 Owner or Owner's Design, ritde

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Providence of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the peio to f, and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Ins 's Signature

Date . _19 9

Commissions A¢1"A7e A1 r'i IV-YNational Board, State, Providence and Endorsements


°

FORM NIS-2 OWNER'S RLPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Sectlon XI



2. Plant Address:

la. Date May27,1999

Sheet 1 of 1


12700 Haqers Ferry Road. Huntersville, NC 28078


3. Work Performed By: Duke Power Company Address: 526 S, Church Street, Charlotte NC 28201-1006



3a. Work Order #:

3b. NSM or MM #:

98149341 RelIr OtrWgnlio, Job#

MGMM - 10952


5. (a) Applicable Construction Code: ASME III 19Z1 Edition, Summer and Winter Addenda, (b) Applicable Edition of Section XI Utilized for Repairs or Replacements: 1989, No Addenda


N/A Code Cases


Replacement (yes or no) A PSA 03 Repaired, []No

2MCA-S-NV-504-1- Duke Power 14183 N/A Mechanical N/A El Replaced, KK Snubber E3 Replacement 03 Yes

B Lisega 03 Repaired, EINo

2MCA-S-NV-504-1- Duke Power 61224-36 N/A Hydraulic N/A 03 Replaced, KK Snubber E]Replacement 0 Yes

03 Repaired, 03 No 0 Replaced, _0 Replacement 03 Yes

D 0 Repaired, 03 No 0 R3eplaced, _0 Replacement 0 Yes


_,__3 Replacement 03 Yes 0F Repaired, 0 No 0 Replaced, ]0 Replacement 0 Yes


Form NIS-2 (Back)


7. Description of Work Replaced PSA Mechanical Snubber with a Lisega Hydraulic Snubber

8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. Li Other 0 Exempto


9. Remarks




Signed .) FL Grass Jr..QA Tech Specialist Date 19_1 Owner or neer's Designee, Title


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period ,.-7--qto ."-,"9; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

In-spectr' ure Cmis ons l "ard, Ste, Province and'Endorsements

1 MDate

FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Sectaon XI


526 S. Church Street, Charlotte. NC 28201-1006

2. Plant Address:

la. Date July 15.1999 Sheet 1 of 1


12700 Haaqers Ferry Road, Huntersville, NC 28078




3a. Work Order #:

3b. NSM or MM #:

98150360 Rtpeor Organizaoý Job #

N/A

4. (a) Identification of System: SM - Main Steam 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases

(b) Applicable Edition of Section XA Utilized for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)



Replacement (yes or no) A 10 Repaired, I0No

2MCA-SM-H020 Duke Power 18871 N/A N/A N/A I[Replaced, O3 Replacement 0] Yes

B 03 Repaired, E[No

2MCA-SM-H020 Duke Power 21359 N/A N/A N/A 03 Replaced, _EIReplacement C0 Yes

C 0 Repaired, 0 No o3 Replaced, [] Replacement 0 Yes

D 0] Repaired, 0 No o Replaced, [] Replacement 0 Yes

E 0 Repaired, 0 No o Replaced, 1O Replacement 0 Yes

F 03 Repaired, 0] No O[ Replaced,

[O Replacement 0 Yes


Form NIS-2 (Back)



8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. 0 Other 11 Exemptr-I

Pressure _ psig Test Temp. OF Pressure psig Test Temp. - OF Pressure psig Test Temp. _ F

9. Remarks




Signed ". & 2 FL Grass Jr., QA Tech Specialist Date July 15 , 1999 Owner dr Owner's Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owners Report during the period -to L--- 0.. ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R.D. Klein Commissions NB7728, NC853, N-1 Inspect s S nature National Board, State, Province and Endorsements

Dtate


FORM NIS-2 OWNER'S RI . - FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XA

1. Owner Address: Duke Power Compan


2. Plant Address:

1 a. Date June 3. 1999 Sheet 1 of 1


12700 Haaqers Ferry Road, Huntersville, NC 28078


3. Work Performed By: Duke Power Companv Address: 526 S. Church Street, Charlotte NC 28201-1006



3a. Work Order #:

3b. NSM or MM #:

98150372Repair Orgnizo Job #

N/A


5. (a) Applicable Construction Code: ASME I 1971 Edition, Summer and Winter Addenda, (b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989, No Addenda

N/A Code Cases



Replacement (yes or no) A 13 Repaired, EiNo

1-MCA-SM-H1 1 Duke Power 22389 N/A N/A N/A EIReplaced, 0 Replacement 0 Yes

B 0 Repaired, I•No

1-MCA-SM-H11 Duke Power 15720 N/A N/A N/A 0 Replaced, .IReplacement 03 Yes 03 Repaired, 0 No

03 Replaced, _ 0 Replacement 03 Yes


E 0 Repaired, 0 No 0 Replaced, _0 Replacement 0 Yes 0 Repaired, 03 No 03 Replaced, _0 Replacement 0 Yes


Form NIS-2 (Back)



8. Test Conducted:Hydrostatic E0 Pneumatic 0 Nom. Operating Press. El Other E] Exempto

Pressure psig Test Temp. OF Pressure psig Test Temp. -F Pressure psig Test Temp. OF

9. Remarks




Signed -..7 g FL Grass Jr..QA Tech Specialist Date ,/J .19 1.q Owner or Owner's Designee, Titlo

Page 2 of 2 Revision S

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owners Report during the period &!"I to - : and state that to the best of my knowledge and belief, the Owner has performed examinati6ns and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

-- A, t__Nat Commissions &% rd 7 S 7 rL c 1 5E lnspectorv'sigrture 'National Board, State,'Province and Eri~dorsernents

19-9?


1. Owner Address:

2. Plant Address:

-Duke Power Company




Ia. Date 9-26-00

Sheet 1 of

2a. Unit: El 1 ] 2 [] 3 [] Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order# 98182096-16 Repair Otganimatlon Job #


Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # n/a

4. (a) Identification of System: SV- MAIN STEAM VENT TO ATMO 4. (b) Class of System: B





Nam of Component Name of Mfg. Mfg. Serial No. National Board No. Other Identification Year Built Replacement Stamped (yes or no)

A 2SV 7 BABCOCK WILCOX 15958-5-2 12 2SV 1977 M Repaired, 0 No []Replaced,

o Replacement 0 Yes

o] Repaired, 0 No [B Replaced,

I"3 Replacement [3 Yes o Repaired, 0 No

C Replaced,


D 0 Repaired,. [0 No D Replaced,


o Repaired, 0 No E 0 Replaced,


O Repaired, [3 No F [0 Replaced,


Page I o(2 Revision 7

Form NIS -2 (Back)


7. Description of work: WELD BUILD UP ON BONNET OF VALVE

8. Test Conducted : Hydrostatic 0 Pneumatic D Nom. Operating Press. 0 Other [I Exempt M

psig psig psig



CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period. 7?.e,2. to7C•-6 -C ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Klein-44) .t/ Inspectorl 2gf0a4re

Date 966, 20 CO


Page 2 of 2 Revion 7


9. Remarks -

OF OF OF


Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed E. P. Robinson Exec. Supp.s&&• *i/ Q Date 9-26 20 00

Owner or Owner's IMsign&, Title

FORM NIS-2 OWNER'S REPORT As Required By The Provisic

REPAIRS OR REPLACEMENTS rhe ASME Code Section X)

1. Owner Address:

2. Plant Address:

Duke Power Company

526 S. Church Street. Charlotte. NC 28201-1006



2a. Unit: F] I Z 2 [] 3 [] Shared (specify units)

3. Work Performed By: Duke Power Companv 3a. Work Order# 98182096/01

Address: 526 S. Church Street. Charlotte, NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. NIA Expiration Date: N/A 3b. NSM or MM # N/A

4. (a) Identification of System: SV 4. (b) Class of System: B






A Valve 2SV-7 B & W 15958-5-2 12 SV 1977 0 Repaired, No 0] Replaced,

S0 Replacement 0g Yes B 0 Repaired, [I No B0 Replaced,

[3 Replacement [I Yes

C o Repaired, 0 No C Replaced, 0] Replacement 0 Yes

D o Repaired, 0 No D[3 Replaced, , , [O Replacement 0 Yes

E [o Repaired, 0 No E Replaced,

[] Replacement 0 Yes o 0 Repaired, 0 No F Replaced, [] Replacement 0 Yes


la. Date

Sheet

10/05/00

I of I

Form NIS -2 (Back)


7. Description of work: Replaced plug assembly

8. Test Conducted : Hydrostatic [] Pneumatic 0 Nom. Operating Press. E0 Other 0 .. Exempt 0.


9. Remarks:



Type Code Symbol Stamp N/._A Certificate of Authorization No. N/A Expiration Date N/A Signed F. R. Sorrow Exec. Supp. ' Date 10/05 20 00


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period Cq.-(. -- 00l to /0-1, --& ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. K~leiE/ Commissions NB7728, NC853, N-I Inspector's i ture National Board, State, Province and Endorsements

Date (4L- , 2<

Puge 2 of 2 Rciion 7



2. Plant Address:



la. Date June 29, 2000

Sheet 1 of 1



3. Work Performed By: j Duke Power Company Address: 526 S, Church Street, Charlotte NC 28201-1006



;I 3a. Work Order #: 98220267 RPe&rOmwhnz.to Jcb#



5. (a) Applicable Construction Code: ASMSJII 19Z1 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)




A 0 Repaired, PNo 2-MCA-ND-H5508 Duke Power 14936 N/A N/A N/A 0 Replaced,

... _ [Replacement 03 Yes

B 0 Repaired, 0 No 2-MCA-ND-H5508 Duke Power 21746 N/A N/A N/A 0 Replaced,

13 Replacement 03 Yes 0 Repaired, 03 No O3 Replaced, _ _ Replacement E3 Yes

D 10 Repaired, 0 No O Replaced, ]0 Replacement 0 Yes


-E3 Replacement 0 Yes F 13 Repaired, 03 No

0 Replaced, ____________ ____________________ ________ ____ Replacement 0] Yes


Form NIS-2 (Back)


7. Description of Work Replaced snubber

8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. 0 Other 0 Exemptlo

Pressure _ _ psig Test Temp. _ OF Pressure psig Test Temp. __ OF Pressure _psig Test Temp. _ OF

9. Remarks




Signed VAe 42 FL Grass Jr..QA Tech Specialist Date 07Ownep'6r Owner's Designee, Titoe


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owners Report during the period "--A' 0o to "2-L•C and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, conceming the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

igQ •0 R.D. Klein Commissions NB7728, NC853, N-I n s Natonal Board, State, Province and Endorsements

Date 4 L 9 ;M


1. Owner Address:

2. Plant Address:

Duke Power Company

526 S. Church Street, Charlotte, NO 28201-1006


Ia. Date September 11, 2000

Sheet 1 of 1





4. (a) Identification of System: CA - Auxiliary Feedwater

3a. Work Order#: 98221268 Raepek Orgizgq Jeb#

3b. NSM or MM #:


N/A

5. (a) Applicable Construction Code: ASME-II 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)


Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Repaired, Replaced, or ASME Code Stamped Replacement (yes or no)

A C3 Repaired, 0 No

2-MCA-CA-60 Duke Power'. 15679 N/A N/A N/A OReplaced, [0 Replacement 03 Yes

B 03 Repaired, ONo 2-MCA-CA-60 Duke Power 18871 N/A N/A N/A 03 Replaced,

__Replacement 0 Yes C 0 Repaired, 0 No


D 0] Repaired, 0 No 03 Replaced, 13 Replacement 0 Yes

E .0 Repaired, 03 No 0 Replaced, _0 Replacement -0 Yes

0 Repaired, 0 No 0 Replaced,

__ Replacement 0] Yes


Form NIS-2 (Back)



8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. 0 Other 0 Exempt[l

9. Remarks

Pressure -psig Test Temp. °F Pressure psig Test Temp. OF Pressure p psig Test Temp. OF




Signed ,O,4WQ FL Grass Jr., QA Tech Specialist Date // 2a9 Owner or.,ner's Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period 9-5.-OO to +-W'-O and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.


S I.-I-. R.D. Klein Dnsapt, or- tignature Date ° ,- aOC6






Sheet 1 of 1

2. Plant Address:

12700 Hagers Ferry Road,. Huntersville, NC 28078




4. (a) Identification of System: CA- Auxiliary Feedwater

3a. Work Order #:Repair OrWantlN Job#

3b. NSM or MM #:


N/A

5. (a) Applicable Construction Code: ASME III 19Z. Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xi Utilized for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)


Column 1 Column 2 Column 3 . Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Repaired, Replaced, or ASME Code Stamped

_......._Replacement (yes or no)

A 03 Repaired, 0 No 2-MCA-CA-56 Duke Power. 14807 N/A N/A N/A OReplaced,

_0 Replacement 0 Yes B [] Repaired, ONo

2-MCA-CA-56 Duke Power 10734 N/A N/A N/A [] Replaced, []Replacement 0 Yes

C [] Repaired, '0 No 03 Replaced, _ 0 Replacement 0 Yes

D 03 Repaired, 0 No o3 Replaced, _3 Replacement [3 Yes

E .0 Repaired, 03 No 0 Replaced, 03 Replacement 0 Yes F0 Repaired, 0 No O3 Replaced, _0 Replacement 0 Yes



Form NIS-2 (Back)



8. Test Conducted:Hydrostatic 0 Pneumatic El Nom. Operating Press. El Other 0l ExemptO

9. Remarks



CERTIFICATE OF COMPUANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the ASME Code, Section Xl.


Signed FL Grass Jr., QA Tech Specialist Date /// , Owner o Owner's Designee, Ti

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period .---- to ..-)p-o0 ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

SR.D. Klein IDnspe ct'4 Signature Date 01--] , qe 0• 0




I. Owner Address:

2. Plant Address:

Duke Power Company




la. Date 09-21-00

Sheet 1 of 1

2a. Unit: [I 1 ] 2 E] 3 F1 Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order # 98237248-10 Repair Organizntion Job #

Address: 526 S. Church Street. Charlotte. NC 28201-1006

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # MGMM-11289

4. (a) Identification of System: ND RESIDUAL HEAT REMOVAL 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASMEIII 1971 Edition, Summer and Winter Addenda, N/A Code Cases




Name of Component Name of Mfg. Mfg. Serial No. National Board No. Other Identification Year Built Replacement ___Stamped (yes or no)

A VALVE 2ND 23 BORG WARNER 4626 40 ND 1975 0 Repaired, D No o] Replaced, [o Replacement 0 Yes o[ Repaired, 0 No B"3 Replaced, E3 Replacement 0 Yes

C o Repaired, 0 No [C Replaced,

1 1 [o Replacement [3 Yes D [o Repaired,. 0 No D0 Replaced,

[o Replacement -0 Yes

E [o Repaired, 0 No [0 Replaced, 0] Replacement 03 Yes

O[ Repaired, 0 No [F Replaced,

[I Replacement 0 Yes

Page l of 2 Revision 7

Form NIS -2 (Back)


7. Description of work: WELD NEW BACKSTOP ON TO VALVE BONNET

8. Test Conducted: Hydrostatic 0 Pneumatic [] Nom. Operating Press. 0 Other-[] Exempt o


9. Remarks:


CIERI'IHCATE OF COMPLIANCE We certify that he statements made in the report are correct and this repair or replacement conforms to the rules of the ASME Code, Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed E. P. Robinson Exec. Supp. Date 09-21 20 00


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period •"I..O to- ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Klein AWO OAA-1

Ing5tor' s Si-Cnure

Date qn 20,




1. Owner Address:

2. Plant Address:

Duke Power Company




la. Date 09-21-00

Sheet 1 of I

2a. Unit: ']l 1 2 F1 3 [] Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order # 98237249-11 Repair Organization Job#


Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # MGMM- 11289

4. (a) Identification of System: ND RESIDUAL HEAT REMOVAL 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME fI 1921 Edition, Summer and Winter Addenda, N/A Code Cases

(b) Applicable Edition of Section XI Utilizing for Repairs or Replacements: 1989. No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)




A VALVE 2ND 8 BORG WARNER 4625 39 ND 1975 W Repaired, 0 No AR Replaced,

E] Replacement 0 Yes

B [] Repaired, [3 No [o Replaced, E3 Replacement 0 Yes

C oI Repaired, 0 No [] Replaced,

j-[O Replacement 0 Yes D [] Repaired, • 0 No

[D Replaced, [0 Replacement 0l Yes

o Repaired, 0 No E [] Replaced,

]0 Replacement 0 Yes 0 Repaired, 0 No

F [ Replaced, [] Replacement 0 Yes


Form NIS -2 (Back)


7. Description of work: WELD NEW BACKSTOP ON TO VALVE BONNET

8. Test Conducted: Hydrostatic 0 Pneumatic 0 Nom. Operating Press. 0 Other.0 Exempt i


psig psig psig


OF OF OF

9. Remarks :



Type Code Symbol Stamp NIA Certificate of Authorization No. N/A

Signed E. P. Robinson Exec. Supp. , Date 09-21 Owner or Owner's Designee, TitlI

T/A

20 00

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period >",--o6 to - ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D.Klein Inspecto0rs 'gnade

Date , 20-0



Expiration DateN


1. Owner Address:

2. Plant Address:

-Duke Power Company

526 S, Church Street, Charlotte, NC 28201-1006



1 a. Date 09-23-00

Sheet I of 1

2a. Unit: El 1 Z 2 [- 3 EQ Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order# 98251940-30 Repair Organization Job#


Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # MGMM10698

4. (a) Identification of System: NV CHEM. & VOL. CONTROL 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME M 1971 Edition, Summer and Winter Addenda, N-416-1 Code Cases





A PIPING DUKE POWER N/A .80 2NV 1982 0 Repaired, 0 No [3 Replaced, ,, Cg Replacement 0 Yes

B [3 Repaired, 0 No t. [0 Replaced,

S.... O] Replacement [3 Yes C [3 Repaired, [3 No

[o Replaced, [3 Replacement Q Yes

D 0 Repaired, [3 No D 0 Replaced, [I Replacement [3 Yes

E 0 Repaired, 0 No [0 Replaced,

0] Replacement 0 Yes [0 Repaired, 03 No F3 Replaced,

I [o Replacement [3 Yes


Form NIS -2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used , provided (I) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of work: ADD FET=INGS FOR HP & LP INSTR. LOOP

2NVLT 5761 FOR VCT

8. Test Conducted: Hydrostatic " Pneumatic 0 Nom. Operating Press. 0 Other 4J Exempt [

32 psig psig psig

Test Temp 75 Test Temp Test Temp


Type Code Symbol Stamp N/A Certificate of Authorization No. N/A I/A

20 00Signed E. P. Robinson Exec. Supp_ Date 09-29 Owner or Owner's Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period :%4QS:f)C to q.-30W ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Klein % JA Inspector's Si-gature

Date 930 ,20



9. Remarks :

OF OF OF



Exniration Date, N

FORM NIS-2 OWNER'S REPORT As Required By The Provisio.

REPAIRS OR REPLACEMENTS rhe ASME Code Section XI

1. Owner Address:

2. Plant Address:

Duke Power Company




2a. Unit: [] 1 0 2 E] 3 E] Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order# 98252135



4. (a) Identification of System: SM 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME M 1971 Edition, Summer and Winter Addenda, N/A Code Cases





OReplairmed, 0 No

A Valve Kerotest JH13-2 6985 2SM-18 1975 [3 Repaired, 0 No [] Replaced, _ Replacement 0 Yes

B o Repaired, 0 No O Replaced, [o Replacement 0 Yes

C 0 Repaired, 0 No [C Replaced,

0] Replacement [0 Yes D o Repaired, 0 No

0 Replaced, [] Replacement 0 Yes

E O Repaired, [3 No [E Replaced,

]0 Replacement 0l Yes El Repaired, El No

F 0[ Replaced,

_E Replacement El Yes


la. Date

Sheet

09/29/00

1 of 1

Form NIS -2 (Back)


7. Description of work: Replaced valve disc

8. Test Conducted: Hydrostatic [] Pneumatic 0

Pressure

Pressure Pressure

psig

psig psig

Nom. Operating Press. 0 Other 0 Exempt 0

Test Temp

Test Temp

Test Temp




Signed F. R. Sorrow Exec. Supp. Date 09/29 20 00 Owner or Owner's Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period -ýg•-'..O to i-3c.0•O . ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Ki Commissions NB7728, NC853, N-I

Inspector's Sigialure National Board, State, Province and Endorsements

Date ,-SQ 0 20A)Q,

Pge 2 of 2 Revisiok 7

9. Remarks :

OF

OF OF

FORM NIS-2 OWNER'S REPOR.3 As Required By The Provisi(

REPAIRS OR REPLACEMENTS The ASME Code Section XI

1. Owner Address:

2. Plant Address: M

12

2a. Unit: F1 I] 2 [1

3. Work Performed By:

Address:

Duke Power Company

526 S. Church Street Charlotte, NC 28201-1006

Ia. Date

Sheet

09/29/00

1 of 1

cguire Nuclear Station


3 E] Shared (specify units)

Duke Power Company


3a. Work Order # 98258913/03 Repair

Organization Job #


4. (a) Identification of System: RF 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME II 1971 Edition, Summer and Winter Addenda, N/A Code Cases

(b) Applicable Edition of Section XI Utilizing for Repairs or Replacements: 1989 No (1992 through 1992 Addenda for Class MC and CC and their supports) Addenda


Column I Column 2 Column 3 Column 4 Column 5 Col. 6 Column 7 Column 8

Name of Component Name of Mfg. Mfg. Serial No. National Board Other Year Repaired, ASME Code No. Identification Built Replaced, or Stamped (yes or

Replacement no)

A Valve TRW J6814 11 1RF-834 1979 0 Repaired, 0 No [] Replaced, 0[] Replacement 0 Yes

B Vvalve Anderson N15031 14 IRF-834 1982 [ Repaired, 0 No

Greenwood [0 Replaced, __ Replacement 0 Yes

C 0 Repaired, 0 No 0 Replaced, [3 Replacement 0 Yes

D [O Repaired, 0 No D0 Replaced,'

11 Replacement 0 Yes O[ Repaired, 0 No E0 Replaced, o Replacement 0 Yes O1 Repaired, 0 No 0 Replaced, 0] Replacement 0 Yes


Form NIS -2 (Back)


7. Description of work: Replaced valve, studs and nuts in flange

8. Test Conducted : Hydrostatic C) Pneumatic [I Nom. Operating Press. [D Other 0 Exempt []


9. Remarks:



Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed F. R. Sorrow Exec. Su Date 09/29 20 00

Owner or Owner"s Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period r---04 to9•ga--00 ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. KleinA Commissions NB7728, NC853, N-I Inspector's Signure National Board, State, Province and

Endorsements

Date -q _9 200

Pa€g 2 of 2 Revixkln 7


1. Owner Address:

2. Plant Address:

Ia. Date 09-23-00

Sheet 1 of I

-Duke Power Company




2a. Unit: C 1 0 2 El 3 0 Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order # 98263089-13 Repair Organization Job #

Address: 526 S. Church Street, Charlotte. NC 28201-1006


4. (a) Identification of System: SV MAIN STEAM VENT TO ATMOS. 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME 1111971 Edition, Summer and Winter Addenda, N/A Code Cases



Column 1 Column 2 Column 3 Column 4 Column 5 Col. 6 Column 7 Column 8 Repaired, Replaced, or ASME Code Name of Component Name of Mfg. Mfg. Serial No. National Board No. Other Identification Year Built Replacement Stamped Cyes or no)

A VALVE 2SV 13 BABCOCK WILCOX 15958-5-3 13 SV 1977 0 Repaired, [3 No [3 Replaced,

.. [0 Replacement 0 Yes

B O Repaired, El No [B Replaced, [0 Replacement 0 Yes [] Repaired, 0 No

C 0[ Replaced, [o Replacement 0 Yes

D El Repaired,. 0 No o Replaced, 1o Replacement 0 Yes.

E0 Repaired, [3 No E ]0 Replaced,


0 Repaired, 0 No F0 Replaced, 0o Replacement 0 Yes


Form NIS -2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used , provided (1) size is 8 1/2 in. x II in. (2) information in items I through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of work: WELD BUILDUP ON BONNET OF VALVE

8. Test Conducted: Hydrostatic 0 Pneumatic [] Nom. Operating Press. 0 Other.Q Exempt o


psig psig psig


OF OF OF

9. Remarks :



Type Code Symbol Stamp N/A Certificate of Authorization No. N/A [/A

20 00Signed E. P. Robinson Exec. Supp. 5 _ Date 09-23


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period 9 ,4 qC4O!. to I-1j, ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Klein Inspector' - nature

Date 4-.3 20(SXP



•xnir:•ticm I'•t,•. NT

FORM NIS-2 OWNER'S REPORT As Required By The Provisio

ZEPAIRS OR REPLACEMENTS fhe ASME Code Section XI

1. Owner Address:

2. Plant Address:

Duke Power Comnany




2a. Unit: [I- 1 [ 2 E] 3 [] Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order # 98263089/01

Address: 526 S. Church Street, Charlotte, NC 28201-1006 Repair Organization Job #


4. (a) Identification of System: SV 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME m 197L Edition, Summer and Winter Addenda, N/A Code Cases




Name of Component Name of Mfg. Mfg. Serial No. National Other Year Repaired, ASME Code Board No. Identification Built Replaced, or Stamped (yes or BoaN . dReplacement no)

A Valve 2SV-13 B & W 15958-5-3 13 SV 1977 D Repaired, 0 No O] Replaced,

[0 Replacement 0 Yes o] Repaired, E] No o Replaced, [I Replacement [3 Yes

C o Repaired, 0 No

o Replaced, [] Replacement 0 Yes

D ol Repaired, 0 No D Replaced, D] Replacement 0 Yes

oE Repaired, 0 No ""0 Replaced,

"O Replacement 0 Yes

o] Repaired, 0] No ""0 Replaced,

[I Replacement 0 Yes


la. Date

Sheet

10/05/00

1 of 1

Form NIS -2 (Back)


7. Description of work: Replaced plug assembly

8. Test Conducted: Hydrostatic 0 Pneumatic []

Pressure Pressure

Pressure

psig psig

psig

Nom. Operating Press. 0 Other 0 Exempt E

Test Temp Test Temp

Test Temp




Signed F. R. Sorrow Exec. Supp. ,_.. -.. 4,.. Date 10/05 20 00 Owner or Owner's Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period c--0-..o to 1.-6 -- 'DO ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Klein ---- JA... Commissions NB7728, NC853, N-I Inspector's Sigature National Board, State, Province and Endorsements

Date (0-(0 200"'

Pag, 2 of 2 Rvismn 7

9. Remarks :

OF OF OF

FORM NIS-2 OWNER'S REPORT FOR REPAIRSOR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI



2. Plant Address:


Sheet 1 of 1



2a. Unit: 01 E2 03 OShared (specify Units )




3a. WorkOrder#:

3b. NSM or MM #:


98264158Repalr Orgenization Job#

MGMM-1 1127

5. (a) Applicable Construction Code: ASMEIII 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)


Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Repaired, Replaced, or ASME Code Stamped Replacement (yes or no)

A 0 Repaired, lNo 2-MCR-NV-5180 Duke Power N/A N/A N/A N/A 03 Replaced,

.__._I__Replacement 03 Yes B 0 Repaired, 0 No


C 0 Repaired, 03 No 03 Replaced, 0 Replacement 0 Yes

D 03 Repaired, 0 No 03 Replaced, [0 Replacement 0 Yes

E 0 Repaired, 0 No 03 Replaced, ""_ Replacement 03 Yes

"0 Repaired, 0 No "0 Replaced,

]0 Replacement 0 Yes


Form NIS-2 (Back)


7. Description of Work Replaced spring can

8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. 0 Other EJ ExemptlZ


9. Remarks




Signed FL Grass Jr., QA Tech Specialist Date ___,

&Oner, OrOwner's Designee, lWte


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Coinpany of Hartford Connecticut have inspected the components described in this Owner's Report during the period -o . to .'-f-OO : and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this ins

R.D. Klein Commissions NB7728, NC853, N-I Inspectors Signatu a- National Board, State, Province and Endorsements

Date gýA'- COD


1. Owner Address:

2. Plant Address:

Duke Power Company



12700 Hauers Ferry Road. Huntersville, NC 28078

la. Date 10-10-00

Sheet 1 of I

2a. Unit: - 1 Z 2 El 3 [1 Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order # 98264158-15 Repair Organization Job#


Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # MGMM1 1127

4. (a) Identification of System: NV CHEM. & VOL. CONTROL 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME HI 1971 Edition, Summer and Winter Addenda, N-416-1 Code Cases



Column 1 Column 2 Column 3 Column 4 Column 5 Col. 6 Column 7 Column 8 Repaired, Replaced, or ASME Code Name of Component Name of Mfg. Mfg. Serial No. National Board No. Other Identification Year Built Replacement Stamped (Cyes or no

A VALVE 2NV 454 CCI 100072-1-2 55 2NV 2000 [0 Repaired, 0 No o3 Replaced,

S.0 [ Replacement 0 Yes

B HANGER 2MCR-NV- DUKE POWER N/A N/A N/A 2000 D Repaired, 0 No o[ Replaced, 5180 ._ 0 Replacement 0 Yes

C 0 Repaired, E3 No [C Replaced, [o Replacement 0 Yes

D O Repaired,. E No 0 Replaced, [o Replacement [3 Yes

E 0 Repaired, [3 No E0 Replaced, r0O Replacement 0 Yes o] Repaired, 0 No F0 Replaced, I-1 Replacement 10 Yes


Form NIS -2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used , provided (1) size is 8 1/2 in. x I I in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of work: REPLACE VALVE 2NV 454 & SPRING CAN ON HGR

2 MCR-NV-5180 (ITEM # 15)

8. Test Conducted: Hydrostatic [I Pneumatic 0 Nom. Operating Press. 0 Other 0

9. Remarks : ONE SIDE OF VALVE IS 2235 PSIG AND 330 PSIG ON OTHER SIDE



OF OF OF

Pressure 2235 psig Pressure 330 psig Pressure psig

Exempt []


Type Code Symbol Stamp NIA Certificate of Authorization No. N/A Expiration Date N/A Signed F. R. Sorrow Exec. Supp .-• All, ý Date 10-10 20 00


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have ins ted the components described in this Owner's Report during the period c-1-O0 to -/-11M ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Kh Commissions NB7728, NC853, N-I Inspector's Si at e National Board, State, Province and Endorsements

Date / 2, 20(



1. Owner Address:

2. Plant Address:

1 a. Date October 9. 2000









3a. Work Order#:

3b. NSM or MM #:

98265754 Repair OW&Won Job #

N/A


5. (a) Applicable Construction Code: ASME III 197t Edition, Summer and Winter Addenda, N/A Code Cases

(b) Applicable Edition of Section XI Utilized for Repairs or Replacements: 1989, No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)


Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identificatlon Year Built Repaired, Replaced, or ASME Code Stamped



2-SM-VA-1AB Atwood - Morrell 5-623 N/A N/A 1976 0 Replaced, _iReplacement E[Yes

B 0 Repaired, 03 No o3 Replaced, E3 Replacement 03 Yes

C C3 Repaired, 03 No o Replaced,

_0 Replacement 03 Yes D 0 Repaired, 0 No

0 .Replaced,

_3 Replacement 0 Yes E 0 Repaired, 0 No

"0 Replaced,

""] Replacement 0 Yes

F [0 Repaired, 03 No 03 Replaced,



Form NIS-2 (Back)



8. Test Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. IOther 0 Exempto

Pressure psig Test Temp. F__ F Pressure _ psig Test Temp. OF Pressure _ _ psig Test Temp. - OF

9. Remarks

(Applicable Manufactureres Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are conrct and this repair or replacement conforms to the rules of the ASME Code, Section XI.


Signed t FL Grass Jr, QA Tech Specialist Date _,__

4 n rwner's De.mgne, Te

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I ConLpany of Hartford Connecticut have inspected the components described in this Owners Report during the period -4,6 to/o-',-- C) and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, conceming the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

S NR.D. Klein Commissions NB7728, NC853, N-I InspectoeirS~jnature National Board, State, Province and Endorsements

Date -d O


FORM NIS-2 OWNER'S REPOR:,' As Required By The Provisw.

REPAIRS OR REPLACEMENTS The ASME Code Section XI

1. Owner Address:

2. Plant Address:

Duke Power Company




2a. Unit: l 1 Z 2 El 3 [1 Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order # 98267345/01




5. (a) Applicable Construction Code: ASME 111 1971 Edition, Summer and Winter Addenda, N/A Code Cases




Ia. Date

Sheet

09/26/00

1 of 1

Column I Column 2 Column 3 Column 4 Column 5 Col. 6 Column 7 Column 8

Name of Component Name of Mfg. Mfg. Serial No. National Other Year Repaired, ASME Code Board No. Identification Built Replaced, or Stamped (yes or

a NReplacement no)

O' Repaired, 0] No A Valve Kerotest SVF- 1-25 16712 2NV-77 1977 3 Repaced,

[]Replaced, __ Replacement [ Yes

B [o Repaired, 0 No [B Replaced,


C O Repaired, 0 No C Replaced,

[] Replacement El Yes D Repaired, El No

D Replaced,


E [] Repaired, El No 0 Replaced,

I 1 o Replacement 1 l Yes

F o] Repaired, El No FE Replaced,

0_ Replacement D Yes

Form NIS -2 (Back)


7. Description of work: Replaced Disc Assembly

8. Test Conducted : Hydrostatic 0 Pneumatic [I Nom. Operating Press. 0 Other 0 Exempt [

psig psig

psig




Type Code Symbol Stamp N/A

Certificate of Authorization No. N/A Expiration Date N/A Signed F. R. Sorrow Exec. Supp.- Date 09/26 20 00

Owner or Owner s Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period 3fjlC-,> to -qnQ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Klein & Commissions NB7728, NC853, N-I nspector's"Signiauure National Board, State, Province and Endorsements

Date , 20

Page 2 ,,f 2

Revison 7

Pressure

Pressure Pressure

9. Remarks :

OF OF

OF


1. Owner Address:

2. Plant Address:

Duke Power Company



12700 Haters Ferry Road, Huntersville, NC 28078

I a. Date 09-23-00

Sheet I of 1

2a. Unit: [] 1 ] 2 E" 3 E] Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order # 98279643-06 Rermttr Organization Job #


Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # MGMM-1 1844

4. (a) Identification of System: FW REFUELING WATER 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASNEI M 1971 Edition, Summer and Winter Addenda, N/A Code Cases




Column I Column 2 Column 3 Column 4 Column 5 Col. 6 Column 7 Column 8 Name of Component Name of Mfg. Mfg. Serial No. National Board No. Other Identification Year Built Repaired. Replaced, or ASME Code

Replacement St0am (yes or no)

A FW PIPING DUKE POWER N/A 54 2FW 1982 I- Repaired, [3 No C3 Replaced, M0 Replacement M Yes

B o Repaired, E3 No B3 Replaced,

0] Replacement [3 Yes

o[ Repaired, [3 No C [ Replaced,

0o Replacement [3 Yes D O Repaired, 0 No [D Replaced,

0] Replacement 0 Yes o Repaired, 0 No

E 0 Replaced, 1 o Replacement 10 Yes o] Repaired, 0 No

[F Replaced, I [] Replacement 0 Yes

Form NIS -2 (Back)


7. Description of work: INSTALL HALF/CPLG ASSEMBLY TO ENCAPSULATE

2FWTX 5050.

8. Test Conducted : Hydrostatic 0 Pneumatic 0 Nom. Operating Press. 0 Other [I Exempt Z]

psig psig psig



CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have ins eted the components described in this Owner's Report during the period 4--'7-O ) to q~ P-L0 ;and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Klein "YUT"?iAv Ins, itr's Sigh ,ure

Date g-T , 20O


Pagc 2 of 2 Revsion 7


9. Remarks :

OF OF OF


Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed E. P. Robinson Exec. Supp. " Date 09-23 20 00



1. Owner Address:

2. Plant Address:

1 a. Date 10-09-00

Sheet 1 of 1

Duke Power Company




2a. Unit: [-E]I [D 2 E] 3 [] Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order# 98312376-05 Repair Organization Job #


Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # MGMM11989

4. (a) Identification of System: NV CHEMICAL &VOLUME CONTROL 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME 1I 1921 Edition, Summer and Winter Addenda, N-416-1 Code Cases



Column 1 Column 2 Column 3 Column 4 Column 5 Col. 6 Column 7 Column 8 Repaired, Replaced, or ASME Code Name of Component Name of Mfg. Mfg. Serial No. National Board No. Other Identification Year Built Replacement Stamped (yes or no)

197 E Repaired, El No A VALVE 2NV 151A KEROTEST CAB22-8 2538 2NV 1979 0 Replaced,


VALVE 2NV 151A KEROTEST AEC1-6 35770 2NV 1983 El Repaired, 0 No o Replaced, __ Replacement El Yes

o] Repaired, [I No D0 Replaced, [3 Replacement [3 Yes

D Repaired, 0[ No

D E0 Replaced, _ _ Replacement 0l Yes

E 0 Repaired,' [3 No E [] Replaced,

0] Replacement [3 Yes

El Repaired, 0l No F l[ Replaced,

[E Replacement El Yes


Form NIS -2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (I) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of work: REPLACE VALVE 2NV151A

8. Test Conducted : Hydrostatic 0 Pneumatic 0 Nom. Operating Press. 0 Other 0 Exempt 0

2640 psig psig psig


9. Remarks :



Type Code Symbol Stamp N/A Certificate of Authorization No. N/A

Signed E. P. Robinson Exec. Supp.-46 & "_ Owner or Owner's Designee, 1lide

Expiration Date N/A

Date 10-09 20 00


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period 4]--0 to/--- ;and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Klei Commissions NB7728, NC853, N-I Inspectd `s ,ature National Board, State, Province and Endorsements

Datet(f•2- ' 20f9


OF OF

OF




2. Plant Address:

Ia. Date September 12, 2000 Sheet 1 of 1



2a. Unit: 01 02 03 0Shared (specify Units _


Type Code Symbol Stamp: N/A Authorization No. NIA Expiration Date: N/A


3a. Work Order#:

3b. NSM or MM #:

98312407 Reperf Or lza n Jcb#

N/A



(b) Applicable Edition of Section XI Utilized for Repairs or Replacements: 1989. No Addenda (1992 through 1992 Addenda for Class MC and CC and their supports)



__________Reclacemrrit (yes or no) [AA 10 Repaired, EfNo

2MCA-SM-HG-0064 Duke Power 6457 N/A N/A N/A 0 Replaced, _.... _EReplacement 3 Yes

0 Repaired, 03 No

0 Replaced, [] Replacement 0 Yes 0 Repaired, 03 No 03 Replaced,

0 Replacement 03 Yes D 10 Repaired, 03 No

0 .Replaced,





.0 [0 Replacement 0 Yes


Form NIS-2 (Back)


7. Description of WorkRenlaced nivot nin

8. Test Conducted:Hydrostatic El Pneumatic 0l Nom. Operating Press. El Other El ExemptlZ

9. Remarks

Pressure _ _ psig Test Temp. OF Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF



Type Code Symbol Stamp N/AI Certificate of Authorization No. N/A Expiration Date N/A

Signed :-/ - FL Grass Jr., QA Tech Specialist Date _.,_


CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period *-'- to ?--/7'.J ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection. istr, t R.D. Klein Commissions NB7728, NC853, N-I Inspector%'Siqnature National Board, State, Province and Endorsements

Date fEJ3.


<

FORM NIS-2 OWNER'S REPOR1 As Required By The Provisi

REPAIRS OR REPLACEMENTS lhe ASME Code Section XI

1. Owner Address:

2. Plant Address:

Duke Power Company




2a. Unit: "-1 ] 2 E] 3 [] Shared (specify units)

3. Work Performed By: Duke Power Comnany 3a. Work Order # 98317278/06




5. (a) Applicable Construction Code: ASME ImI 1971 Edition, Summer and Winter Addenda, N/A Code Cases




Name of Component Name of Mfg. Mfg. Serial No. National Other Year Repaired, ASME Code Board No. Identification Built Replaced, or Stamped (yes or B Replacement no)

A Piping Duke Power N/A 80 2NV 1982 [] Repaired, 13 No [3 Replaced, __ Replacement 0 Yes

B[ Repaired, 0 No [B Replaced, [3 Replacement Q Yes

C O Repaired, 0 No C0 Replaced, [O Replacement , Yes

D [o Repaired, 0 No [] Replaced, [3 Replacement 0l Yes

E E] Repaired, [I No [E Replaced,

]0 Replacement [3 Yes F [] Repaired, 0 No [F Replaced,

__ Replacement [0 Yes


Ia. Date

Sheet

10/09/00

1 of I

Form NIS -2 (Back)


7. Description of work: Replaced studs and nuts in 2NV99FL- I at valve 2NV-93

8. Test Conducted: Hydrostatic [] Pneumatic 0 Nom. Operating Press. El Other C1 Exempt g

psig psig

psig

Test Temp Test Temp

Test Temp




Signed F. R. Sorrow Exec. SuppzI -O-.k Date 10/09 20 00 Owner or Owner's Designee, Title

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period q-!q to 0Jzý ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Klei •& ý Commissions NB7728, NC853, N-I Inspector'Cai -t ue National Board, State, Province and Endorsements

Date/ Q/ , 20-00

Page 2 of 2 R-iswn 7

Pressure Pressure

Pressure

9. Remarks :

OF OF OF

FORM NIS-2 OWNER'S REPOP As Required By The Provisie

ZEPAIRS OR REPLACEMENTS fhe ASME Code Section XI

1. Owner Address:

2. Plant Address:

Duke Power Company




2a. Unit: F1 1 S 2 F1 3 F1 Shared (specify units)

3. Work Performed By: Duke Power Company 3a. Work Order# 98317575/01


Type Code Symbol Stamp: N/.A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # 12030





_ Column 1 Column 2 Column 3 Column 4 Column 5 Col. 6 Column 7 Column 8 !Repaired, ASME Code

Name of Component Name of Mfg. Mfg. Serial No. National Other Year Repaied, ASme Cod Board No. Identification Built Replacement no)

A 2MCA-NV-5313 DUKE POWER N/A N/A N/A N/A 0 Repaired, 0 No E3 Replaced,

• • [0 Replacement [3 Yes o] Repaired, 0l No o Replaced, [o Replacement El Yes

C El Repaired, El No [o Replaced, El Replacement [3 Yes

D [I Repaired, 0l No El Replaced, _ _ Replacement [3 Yes

El Repaired, El No E] Replaced, 1_ El Replacement El Yes

El Repaired, El No [E Replaced, 0E Replacement El Yes

Page I of 2 Revixion 7

la. Date

Sheet

10/07/00

1 of I

Form NIS -2 (Back)


7. Description of work: Cut out and replaced 3/16" weld between item #1 and #4

8. Test Conducted: Hydrostatic [] Pneumatic 0 Nom. Operating Press. [] Other 0 Exempt 0

psig psig

psig

Test Temp

Test Temp Test Temp

Pressure Pressure

Pressure

9. Remarks :

OF

OF OF



Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed F. R. Sorrow Exec. Supp.. - ' Date 10/07 20 00


1, -ýý

CERTIFICATE OF INSERVICE INSPECTION L the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBI and I Company of Hartford Connecticut have inspected the components described in this Owner's Report during the period t)'- O to A '•0 ;and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section XI. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in the Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

R. D. Klein Commissions -NB7728, NC853, N-I Inspectors.gna re National Board, State, Province and Endorsements

Pge 2 of 2 Revisko 7

11.0 Pressure Testinc,

There are three refueling outages scheduled for the second period of the second inspection interval for Duke Power Company's McGuire Nuclear Station Unit 2. This section describes Pressure Tests performed for the second period through

the 2000 refueling outage (also referred to as EOC-13). *The seven remaining Inservice/Functional pressure tests and the three remaining Hydrostatic pressure tests will be summarized in a special report that will cover a time period from the end of EOC-13 until the expiration of the second period on March 1, 2001.

Total Total (%)

Examination Test Requirement Examinations Examinations Examinations

Category Required For Credited For Complete For This Period This Period This Period

B-E System Hydrostatic 0 0 0%

B-P System Leakage Test 3 3 100% (IWB-5221)

B-P System Hydrostatic 0 0 0% Test (IW B-5222) .. . •° ;, . . ....

C-H System 35 *28 80% Inservice/Functional

Test (IWC-5221)

C-H System Hydrostatic 16 *13 81.25% Test (IWC-5222) _

A detailed description of each Examination Category listed above is located in

subsection 11.1 of this report. Results of each Examination Category are located in subsection 11.2 of this report.

*The 7 Category C-H Inservice/Functional pending items are as follows:

C07.030.012, C07.030.020, C07.030.027, C07.030.028, C07.030.031, C07.030.032, & C07.030.034.

*The 3 Category C-H Hydrostatic pending items are as follows: C07.040.018,

C07.040.019, & C07.040.021.

Refueling Outage Report EOC13 McGuire Unit 2 Section 11


11.1 Required Examinations This Outage:

A listing of each VT-2 Visual Examination that is required for EOC-13 through the end of the second period is included in this section.

The information shown below is a field description for the listing format included in this section of the report:

Item No.

ISI Drawing

Required Test

System Name

Required Inspection

Required Procedure

Comments

=ASME Section XI Tables IWB-2500-1 (Class 1) and IWC-2500-1 (Class 2)

= Detail Drawing of Inspection Boundary

= Type of Pressure Test

= Name of Pressure Retaining Component System

= Type of Visual Examination Required

= Required Inspection Procedure




Duke Power Company - McGuire Unit 2 Pressure Testing Item Number Listing

Outage 13

ISI Item Number Drawing

B15.050.001 SEE COMMENTS

Required Test

LEAKAGE

System Name

NC SYSTEM

Required Inspection

VT-2

Required Procedure

QAL-15Comments

Class A Leakage Boundary Dwgs: MCL-2553-1.0, MCL-2553-2.0, MCL-2554-1.0, MCL-2554-1.1, MCL-2554-1.2, MCL-2561-1.0, MCL-2562-1.0, MCL-2562-2.0, MCL-2562-2.1, MCL-2562-3.0, MCL-2562-3.1

This Report Was Generated On: 12/05/2000


Outage 13

Item Number

C07.030.005

C07.030.010

C07.030.012

C07.030.015

G07.030.018

C07.030.020

C07.030.026

C07.030.027

C07.030.028

C07.030.031

C07.030.032

ISI Drawing

MCL-2561 -1.0

MCL-2562-3.1

MCL-2563-1 .0

MCL-2571 -1.0

MCL-2572-1.1

MCL-2572-3.0

MCL-2580-1.0

MCL-2584-1.0

MCL-2591 -1.1

MCL-2592-1.0

MCL-2593-1.2

Required Test

INSER

System Name

ND SYSTEM

INS/FUN NI SYSTEM

INS/FUN NS SYSTEM

INSER FW SYSTEM

INSER NM SYSTEM

FUNC NM SYSTEM

INS/FUN BB SYSTEM

INSER BW SYSTEM

INS/FUN CF SYSTEM

INS/FUN CA SYSTEM

INSER SA/TE SYSTEM

Required Inspection

VT-2

VT-2

VT-2

VT-2

VT-2

VT-2

VT-2

VT-2

VT-2

VT-2

VT-2

Required Procedure

QAL-15

QAL-15

Comments

VT-2 Examination of C02.033.001 & C02.033.002 Telltale Hole also required for ND HX 2A.

This test is required for periods 1,2 and 3

QAL-1 5 VT-2 Examination of C02.033.005 and C02.033.006

Telltale Hole also required for NS HX 2A. This system is partially complete for the 2nd period but

will be 100% complete by 3/1/2001.

QAL-1 5 This test is required for periods 1,2 and 3

Penetrations 2M-358 and 2M-377 - Reference PIP#2-M95-0043

QAL-15 Penetration M-280 - Reference PIP#2-M95-0043

QAL-1 5 Class B penetrations M-335, M-338, M-340 and

M-341. This system is partially complete for the 2nd period but will be 100% complete by 3/1/2001.

QAL-1 5 Penetrations M-300, M-301, M-303 and M-304

QAL-1 5 This system has not been tested for the 2nd period

but will be 100% complete by 3/1/2001.

QAL-15 Penetrations M-153, M-262, M-308 and M-440. Thit,

system is partially complete for the 2nd period but will be 100% complete by 3/1/2001.

QAL-1 5 Penetrations M-1 56, M-286, M-465 and M-31 00. This system is partially complete for the 2nd period


QAL-15 This system is partially complete for the 2nd period



Outage 13

Item Number

C07.030.034

C07.040.006

C07.040.017

C07.040.018

C07.040.019

C07.040.021

IS1 Drawing

MCL-2617-1.0

MCH-2554-1.1

MCH-2562-2.1

MCH-2562-3.0

MCH-2562-3.1

MCH-2563-1.0

Required Test

INSER

System Name

YA SYSTEM

HYDRO NV SYSTEM

HYDRO NISYSTEM

HYDRO NISYSTEM

HYDRO NISYSTEM

HYDRO NS SYSTEM

Required Required Inspection Procedure

VT-2

VT-2

VT-2

VT-2

VT-2

VT-2

Comments


OAL-15 Reference PIP#2-M95-0043. This system has not been tested for the 2nd period but will be 100% complete by 3/1/2001.

QAL-1 5 This test is required for periods 2 and 3 Penetrations M-256, M-343 and M-344

QAL-15 This test is required for periods 2 and 3 Penetration M-321

QAL-1 5 This test is required for periods 2 and 3 Penetrations M-277, M-316 and M-319. This systerr is partially complete for the 2nd period but will be 100% complete by 3/1/2001.

QAL-1 5 This test is required for periods 2 and 3. This system is partially complete for the 2nd period but will be 100% complete by 3/1/2001.

QAL-1 5 VT-2 Examination of C02.033.005 and C02.033.006 Telltale Hole also required for NS HX 2A. This system is partially complete for the 2nd period but will be 100% complete by 3/1/2001.


11.2 Examination Results For This Outage:

The results of each VT-2 Visual Examination that is required for EOC-13 through the end of the second period is included in this section

The information shown below is a field description for the listing format included in this section of the report:

Item Number

ISI Drawing

Required Test

Test Status

Test Result

VT-2 Date

Comments

=ASME Section XI Tables IWB-2500-1 (Class 1) and IWC-2500-1 (Class 2)

= Detail Drawing of Inspection Boundary

= Type of Pressure Test

- Complete, Partial, Not Tested, or Not Required

= Clear, Recordable, or Reportable

= Date VT-2 Visual Examination Was Performed




Duke Power Company - McGuire Unit 2 Pressure Testing VT-2 Results For Outage 13

ISI Item Number Drawing

B1 5.050.001 SEE COMMENTS

Required Test Test Status

LEAKAGE COMPLETE

Test Result

CLEAR

VT-2 Date Comments

10/10/2000 Class A Leakage Boundary Dwgs: MCL-2553-1.0, MCL-2553-2.0, MCL-2554-1.0, MCL-2554-1.1, MCL-2554-1.2, MCL-2561-1.0, MCL-2562-1.0, MCL-2562-2.0, MCL-2562-2.1, MCL-2562-3.0, MCL-2562-3.1



Item Number

C07.030.005

C07.030.010

C07.030.012

C07.030.015

C07.030.018

C07.030.020

C07.030.026

C07.030.027

C07.030.028

C07.030.031

C07.030.032

ISI Drawing

MCL-2561 -1.0

MCL-2562-3.1

MCL-2563-1 .0

MCL-2571 -1.0

MCL-2572-1.1

MCL-2572-3.0

MCL-2580-1 .0

MCL-2584-1.0

MCL-2591 -1.1

MCL-2592-1.0

MCL-2593-1.2

Required Test

INSER

INS/FUN

INS/FUN

INSER

INSER

FUNC

INS/FUN

INSER

Test Status

COMPLETE

COMPLETE

PARTIAL

COMPLETE

COMPLETE

PARTIAL

COMPLETE

NOT TESTED

INS/FUN PARTIAL

INS/FUN PARTIAL

INSER PARTIAL

Test Result

CLEAR

CLEAR

CLEAR

CLEAR

CLEAR

CLEAR

CLEAR

N/A

CLEAR

CLEAR

CLEAR

VT-2 Date Comments11/19/1998 VT-2 Examination of C02.033.001 & C02.033.002 Telltale

Hole also required for ND HX 2A.

04/13/1999 This test is required for periods 1,2 and 3

03/14/1999 VT-2 Examination of C02.033.005 and C02.033.006 Telltale Hole also required for NS HX 2A. This system is partially complete for the 2nd period but will be 100% complete by 3/1/2001.

03/30/1999 This test is required for periods 1,2 and 3 Penetrations 2M-358 and 2M-377 - Reference PIP#2-M95-0043

12/27/1999 Penetration M-280 - Reference PIP#2-M95-0043

04/13/1999 Class B penetrations M-335, M-338, M-340 and M-341. This system is partially complete for the 2nd period but will be 100% complete by 3/1/2001.

12/27/1999 Penetrations M-300, M-301, M-303 and M-304

/ / This system has not been tested for the 2nd period but will be 100% complete by 3/1/2001.

04/13/1999 Penetrations M-1 53, M-262, M-308 and M-440. This system is partially complete for the 2nd period but will be 100% complete by 3/1/2001.

04/13/1999 Penetrations M-1 56, M-286, M-465 and M-31 00. This system is partially complete for the 2nd period but will be 100% complete by 3/1/2001.

07/31/1997 This system is partially complete for the 2nd period but will be 100% complete by 3/1/2001.



Item Number

C07.030.034

C07.040.006

C07.040.017

C07.040.018

C07.040.019

C07.040.021

ISI Drawing

MCL-2617-1.0

MCH-2554-1.1

MCH-2562-2.1

MCH-2562-3.0

MCH-2562-3.1

MCH-2563-1.0

Required Test

INSER

Test Status

NOT TESTED

HYDRO COMPLETE

HYDRO COMPLETE

HYDRO PARTIAL

HYDRO PARTIAL

HYDRO PARTIAL

Test Result

N/A

CLEAR

CLEAR

CLEAR

CLEAR

CLEAR

VT-2 Date //

Comments

Reference PIP#2-M95-0043. This system has not been tested for the 2nd period but will be 100% complete by 3/1/2001.

12/27/1999 This test is required for periods 2 and 3 - Penetrations M-256, M-343 and M-344

03/13/1999

12/28/1998

This test is required for periods 2 and 3 - Penetration M-321

This test is required for periods 2 and 3 Penetrations M-277, M-316 and M-319. This system is partially complete for the 2nd period but will be 100% complete by 3/1/2001.

11/02/1998 This test is required for periods 2 and 3. This system is partially complete for the 2nd period but will be 100%

complete by 3/1/2001.

11/02/1998 VT-2 Examination of C02.033.005 and C02.033.006 Telltale Hole also required for NS HX 2A. This system is partially complete for the 2nd period but will be 100% complete by 3/1/2001.


11.3 Reportable Indications:

None

