duradrive et series ide solid state drive et.pdf · in the task file /cs[1:0] i 38, 37 /cs0 is the...

www.supertalent.com

Overvie w

DuraDrive ET Series IDE Solid State Drive

es

128GB

turPhysical Specifications

Endurance Specifications

Performance Specifications

Environmental Specifications

Reliability Specifications

Super Talent's DuraDrive AT SSD series represent the next generation indata storage. Thanks to a unique Flash disk control chip and premiumNAND Flash memory, DuraDrive AT SSDs combine unprecendented vibration and shock tolerance with impressive speeds. Super Talent'spatented Flash management techniques increase reliability and endurance, and through our software and hardware testing ensuresquality of each DuraDrive AT SSD. The DuraDrive AT series is available ina wide range of form factors and capacities to fit any application. The Dura Drive AT SSD is geared specifically for applications that requirehigh tolerance to environmental conditions. Example industries include:

- Military / Aerospace - Embedded / Industrial Systems - Enterprise Computing - Medical Industry - Casino Gaming

Form Factor 1.3’’ / 1.8’’ / 2.5’’ 1.3’’ 8GB – 32GB 1.8’’ 8GB – 64GB

Capacities

2.5’’ 8GB – 128GB 1.3’’ 50.8mm x 46.5mm x 8.9mm 1.8’’ 69.9mm x 60.0mm x 7.5mm

Dimension

2.5’’ 69.9mm x 100.2mm x 7.5mm IDE Interface

Up to PIO Mode 6 MDMA Mode 4 UDMA Mode 5

Power Supply 5.0Vcc ± 5% Package Complete metal housing

Read Unlimited 8GB 43.8 yrs @ 50GB write-erase/day 16GB 87.7 yrs @ 50GB write-erase/day 32GB 175.3 yrs @ 50GB write-erase/day 64GB 350.7 yrs @ 50GB write-erase/day

Write

128GB 701.4 yrs @ 50GB write-erase/day

Sequential Read Rate 65 MB/sec (max) Sequential Write Rate 50 MB/sec (max) Sequential Read IOPS 58,675 IOPS Access Time 0.1 ms

Shock (operating) 1500G Vibration (operating) 16G

Industrial -40°C to +85°C Operating Temp. Commercial 0°C to +70°C

MTBF +1,000,000 hours Data Reliability Built-in EDC/ECC function Data Integrity 10 years Wear Leveling Algorithm Patent Pending

© 2008 Super Talent Technology. Specifications subject to change without notice. US patent #6,547,130 #7,243,185 #7,301,776 #7,318,117 and others apply. *Usable capacity may be less than specified after formatting. p.1

ssd.supertalent.com

ssd.supertalent.com

Overvie w


Module F

e

tur es

Revision HistoryApril 2, 2008 Rev-A Preliminary Product Specification Released

SYBMOL RATING VALUE UNIT VCC Power Supply Voltage -0.3 to 6.5 V VIN Input Voltage -0.5 to VCC+0.5 V TSTG Storage Temperature -65 to 150 °C

Industrial 0 to 70 TOPR Operating Temperature Commercial -40 to 85

°C

ABSOLUTE MAXIMUM RATINGS

SYMBOL PARAMETER MIN TYP. MAX UNIT VCC Power Supply Voltage 4.5 5.0 5.5 V VIH High Level Input Voltage 2.0 - V VIL Low Level Input Voltage - 0.8 V

RECOMMENDED DC OPERATING CONDITIONS

SYMBOL PARAMETER MIN TYP. MAX UNIT ICCO Operating Current 40 A ICCS Sleep Mode Current 1.2 A VOH High Level Output Voltage VCC-0.8 - - V VOL Low Level Output Voltage - - 0.4 V

DC CHARACTERISTICS (Ta = -40C to 85C, Vcc = 5V +/-10%)

aPIN SYMBOL PIN SYMBOL 1 /RESET 2 GND 3 HD7 4 HD8 5 HD6 6 HD9 7 HD5 8 HD10 9 HD4 10 HD11 11 HD3 12 HD12 13 HD2 14 HD13 15 HD1 16 HD14 17 HD0 18 HD15 19 GND 20 Key 21 DMARQ 22 GND 23 /IOW 24 GND 25 /IOR 26 GND 27 WAIT 28 CSEL 29 /DMACK 30 GND 31 IRQ 32 /IOIS16 33 HA1 34 /PDIAG 35 HA0 36 HA2 37 /CS0 38 /CS1 39 /DASP 40 GND 41 Vcc 42 Vcc 43 GND 44 N/C

Pin Assignment: 44 pin Flash Drive

© 2008 Super Talent Technology. Specifications subject to change without notice. US patent #6,547,130 #7,243,185 #7,301,776 #7,318,117 and others apply. p.2

ssd.supertalent.com

O ervie w

Dura Drive ET Series IDE Solid State Drive

Module F

ea

tur es

Signal Name Dir Pin Description HA[2:0] I 36, 33, 35 A2-A0 are used to select the one of the eight registers

in the Task File /CS[1:0] I 38, 37 /CS0 is the chip select for the Task File registers

while /CS1 is used to select the Alternative Status Register and the Device Control Register

CSEL I 28 This internally pulled-up signal is used to configure this device as a Master or a Slave, if J_CSEL_-EN is grounded by a jumper from B to D. When the pin is grounded, this device is configured as a Master. When the pin is open, this device is configured as a Slave.

HD[15:0] I/O 18, 16,14, 12, 10, 8, 6, 4, 3, 5, 7, 9, 11, 13, 15, 17

All the Task File operations occur in byte mode on the low order bus HD[7:0] while all data transfers are 16 bit using HD[15:0].

/DASP I/O 39 This input/output is the Disk Active/ Slave Present signal in the Master/Slave handshake protocol.

DMARQ O 21 DMA transfer request /DMACK I 29 DMA request knowledge /IOW:STOP I 23 The I/O Write strobe pulse is used to clock I/O data

on the Card Data bus into the Drive controller registers when the Drive is configured to use the I/O interface. The clocking will occur on the negative to positive edge of the signal (trailing edge). During Ultra DMA, this is the stop signal.

/IOR: HDMARDY/HSTROBE

I 25 This is an I/O Read strobe generated by the host. This signal gates I/O data onto the bus from the Drive. Ultra DMA control signal used to extend host transfer cycles.

IRQ O 31 Signal used to interrupt host when service is requested.

/IOIS16 O 32 This output signal is asserted low when this device is expecting a word data transfer cycle.

IORDY: DDMARDY/DSTROBE

O 27 This output signal may be used as IORDY. Ultra DMA control signal used to extend host transfer cycles.

/PDIAG I/O 34 This input/output is the Pass Diagnostic signal in the Master/Slave handshake protocol.

/RESET I 1 This input pin is the active low hardware reset from the host.

GND -- 2, 19, 22, 24, 26, 30, 40, 43

Ground

Key -- 20 This pin is keyed so that the drive can only be connected with the cable pin 1 to drive pin 1.

N/C -- 44 No connect Vcc -- 42, 41 +5V

Configuration Descriptions

Capacity Industrial Temp Commercial Temp 8GB FHD8GC13I FHD8GC13M 16GB FHD16GC13I FHD16GC13M 32GB FHD32GC13I FHD32GC13M

Capacity Industrial Temp Commercial Temp

8GB FHD8GC18I FHD8GC18M 16GB FHD16GC18I FHD16GC18M 32GB FHD32GC18I FHD32GC18M 64GB FHD64GC18I FHD32GC18M

Capacity Industrial Temp Commercial Temp

8GB FHD8GC25I FHD8GC25M 16GB FHD16GC25I FHD16GC25M 32GB FHD32GC25I FHD32GC25M 64GB FHD64GC25I FHD64GC25M

128GB FHD28GC25I FHD28GC25M

Ordering Information - 1.8'' Form Factor




ssd.supertalent.com

Overvie w


Mechanical Specifications for 1.3'' DuraDrive ET SSD

50.80

46.50

26.00

14.00

3.00

8.90

4-M2.5X0.45BOTH SIDE


ssd.supertalent.com

Overvie w


Mechanical Specifications for 1.8'' DuraDrive ET SSD (low capacities)

69.852.750

2.95

0.11

6

0.91

0.35

602.

362

63.452.498

3.200.126

54.1

02.

130

10.14 0.375

M2.5 X 2.8[0.110]TAP MIN (4X)

[0.0

360.

014]

2.820.111

2.13

00.

116

M2.5 X 2.8[0.110] TAP MIN (4X)

7.50

0.29

5

421.654

20.0792

0.07

9

3.99

0.15

7[.399 0.015]


ssd.supertalent.com

Overvie w


Mechanical Specifications for 1.8'' DuraDrive ET SSD (high capacities)

TAP MIN (4X)

0.91

0.35

3.200.126

69.852.750

602.

362

63.452.498

54.1

02.

130

2.95

0.11

6

10.14 0.375

M2.5 X 2.8[0.110]

[0.0

360.

014]

2.820.111

54.1

02.

130

2.95

0.11

6

M2.5 X 2.8[0.110] TAP MIN (4X)

9.60

0.37

8

20.0792

0.07

9 421.654

3.99

0.15

7[.399 0.015]


ssd.supertalent.com

Overvie w


Mechanical Specifications for 2.5'' DuraDrive ET SSD (low capacities)

69.85[2.750]

61.72[2.430]

140.

551

100.

203.

945

4.07[0.160]

76.6

03.

016

9.70

0.38

2

10.14[0.399]

M3 X 4.0[0.157]MAX (4X)

7.50

0.29

5

3.99

[0.1

57]

20.079

421.654

20.

079

30.118 14

0.55

176

.60

3.01

6

M3 X 4.0[0.157]MAX (4X)


ssd.supertalent.com

Overvie w


Mechanical Specifications for 2.5'' DuraDrive ET SSD (high capacities)

61.72[2.430]

69.85[2.750]

140.

551

100.

20[3

.945

]

4.07[0.160]

76.6

03.

016

9.70

0.38

2

10.14[0.399]

M3 X4.0[0.157]MAX (4X)

110.

433

20.079

421.654

20.

079

3.99

[0.1

57]

30.118 14

0.55

176

.60

3.01

6

M3 X 4.0[0.157]MAX (4X)


duradrive et series ide solid state drive et.pdf · in the task file /cs[1:0] i 38, 37 /cs0 is the...

Documents