Sht1DRAWING TITLE:DRAWING No.:REV. No.PROJECT No.:DRAFTSMAN NAME:ITEMDESCRIPTIONYESNOREMARKS1GENERAL1.1Have you familiarise with the drawing workscope?2PREPARATION OF THE DRAWING2.1Engineer's / SD's briefing given ? ---a)on compliance to contract specification, section:-b)on compliance to Classification Body, section:-c)on compliance to Authority Rule, section:-d)on using ex-stock material, document no:-e)on preliminary B.O.M, document no:-f)on owner-approved vendors' listg)on which area to use armoured or non-armour cableh)on cable ampacity table to be usedi)on consumer breaker/starter sizing and selection2.2Is the drawing size correct ? (A0, A1 or A3 )2.3Check drawing title & number as per PPS ?2.4Check owner drawing number ? (If any)2.5Are you using the project drawing title format ?2.6Is the background from mechanical section latest ?Name of the source of information:-2.7Has all unnecessary details being removed from the background ?2.8Has the line work for the background been lightened ? (Only emphasise on electrical system)2.9Have you include the key plan ? (Vessel fwd arrow to be indicated)2.10Are you doing the standardise way of drawing presentation ?Is the cost code number added ?2.11Is vendor information available ?Have compile equipment data/specification and attach to this check list ?Have prepare a list of equipment information which is not available and attach to this check list ?3ELECTRICAL EQUIPMENT SELECTION3.1Have you check correct frequency, rated voltage and current (amp) used ?3.2Are the selected equipment suit the hazardous area requirements ?Is the explosion-proof equipment c/w approved classification body certificate ?3.3Are the selected equipment comply to that area ingress protection (IP) requirements ?3.4Are the selected equipment completely assembled ?3.5Are the selected equipment cable entry size suit this project cable/gland size ?3.6Have you check the material requirements, e.g. SS316, GRP & etc ?3.7Have you check the mounting type, e.g. surface, flush & etc ?Refer KFELS standard document for guidance & suitability3.8Is the indicating light colour scheme check ?3.9Ensure no double tier terminal block is being used. Maintenance difficulty in future.4PREPARING THE ARRANGEMENT & SCHEMATIC4.1Are all information presented clearly and legible ? (Lettering height 2.5mm minimum)4.2Are all outgoing cable tagging according to KFELS method ?4.3Is the panel (power) incoming cable tagged as per respective source drawing cable number?4.4Are all electrical equipment tagging according to KFELS method & also the same itemnumber as in purchase specification document ?4.5Is the symbols and standardisation practise ?4.6Is the equipment name same as mechanical section ?4.7Are all consumer necessary data such as kilowatt and full load current incorporated ?4.8Is the consumer check for 1ph or 3ph power supply requirements ?4.9Is the convector heater unit prepare by mechanical section c/w built-in thermostat and poweron/off switch ?4.10Is the steam heater blower prepare by mechanical section c/w remote manual starter ?If the manual starter require to be purchased by electrical section, get actual motor IFL datafrom vendor to size thermal unit. (Do not calculate using motor KW rating)4.11Is mechanical section inform of the distribution power panel location ?Are cables bottom entry ?4.12To indicate "PCM" in "Revision Column" of the drawing if PCM have been issued.Continue on page 2FILE NAME:- Echeck4

&C&"Arial,"ELECTRICAL DRAFTING CHECK LIST FOR HEATER AND BLOWER SYSTEM&R&9

Page 1 of 2

Sht2Continue from page 1ITEMDESCRIPTIONYESNOREMARKS5INTERFERENCE CHECK5.1Is the electrical equipment spacing check for:-a)accessibilityb)comply to contract specificationc)comply to classification bodyChecking should also take into consideration:-a)miscellaneous working platformsb)handrailsc)ladder position (especially the vertical type)d)equipment coaming/drip pan positione)door swing position6CABLE SIZING6.1Is the single phase outgoing cable 2/C+E or 3/C ? (Same type used in lighting system)6.2Is the conductor size for consumer load #14AWG or 2.5mm minimum ?6.3Refer this project cable ampacity table to select cable size ?6.4Is the armoured or non-armour cable clearly indicated in drawing ?6.5Is cable rating for consumer load higher than breaker amp-trip ?6.6Have you considered voltage drop ?(Engineer to provide/ensure correct calculation formula)7BREAKER SIZING - AMP.TRIP7.1Have you check vendor data ? ---e.g. rating, number of poles and correct voltage used.8FINAL CHECK8.1Have you estimate & input cable length in the database ?8.2Have you input the material quantity in the purchase specification (or B.O.M) database ?8.3Check general notes content ?8.4Are reference drawings used and indicated in this drawing ?8.5Have you save this drawing file in the network ?FILE NAME:- Echeck4DWG START DATE:DWG FINISH DATE:CHECKED BY:CHECKING DATE:LEAD ENGINEER COUNTER-SIGN:

&C&"Arial,"ELECTRICAL DRAFTING CHECK LIST FOR HEATER AND BLOWER SYSTEM&R&9

Page 2 of 2