ecigworld kanger starter kit manual

www.eCigWorld.com.au

For more guides, hints and tips; visit www.eCigWorld.com.au

eCigWorld Kanger Starter Kit Manual

Congratulations on your purchase of this eCigWorld Kanger Starter kit! The following are some basic

instructions on handling, use and care of your equipment.

Please read this guide completely before using your device.

Please also ensure the batteries are fully charged before your first use. The battery is locked when

shipped (see charging and unlocking instructions below).

General Kit contents

eGo/510 compatible Normal or Variable Voltage (either 4 click VV or VV Twist) batteries

Kanger Clearomisers (Protank V1, V1 Mini, Protank V2, V2 Mini, Protank V3, V3 mini, Aerotank series USB charger lead with LED indicator

Optional - Australian wall plug for USB cable

eliquid - Options extra Carry case

How to Fill/Re-fill the clearomiser

Kanger Protank, Aerotank and Subtank series are all Bottom Fill tanks. Please follow this instructions

Unscrew the clearomizer from the battery if your kit has arrived assembled. Always screw/unscrew clearomisers from their base rather than the main body.

Unscrew the bottom hardware from the clearomiser.

Holding the main tube section upside-down, drip or syringe 1.5ml maximum (less if refilling as hold holds some juice even when the clearo is empty) into the tank, ensuring you do not allow liquid to enter the centre tube inside the clearomiser.

Once filled, screw the bottom hardware back on, being careful not to cross thread or over-tighten.

NOTE: Allow 3 – 5 minutes for liquid to absorb into the coil head before first use; otherwise you may experience a burnt taste. Stand the clearomizer upright to assist in the absorption process. When using, never allow the clearomizer to run dry.

Assembly

Screw the clearomiser into the battery. Be careful not to cross thread or over-tighten.



NOTE: Over-tightening chargers, clearomizers and atomizers can damage a battery. Carefully screw on

these components until you begin to feel resistance; then apply a maximum further one-quarter turn.

General Usage

When you receive the battery, it will be locked (see unlocking instructions below). Once unlocked, simply

hold down the button as you take a draw. This activates the device and creates the vapor. Release the

button just prior to the end of your draw.

Battery locking (ON / OFF) feature

The batteries have a button operated lock; which prevents unintended activation of the battery. Batteries are shipped locked. To turn the battery on, click the button rapidly 5 times. The LED will then flash 3 times indicating it is now in standby mode; ready to use. To switch off, click the button 5 times. The LED will flash 3 times and then the battery will be locked.

Variable voltage feature using 4-CLICK Button

Some eliquids vape better at a lower voltage and some higher - and "better" can be somewhat subjective; so having this feature allows you to choose what’s right for you.

To change voltages is very simple - 3 rapid button clicks takes you to the next setting. The current setting is indicated when you press the button by the colour of the LED light. Green signifies the low voltage (~3V), blue medium (~3.6V) and red, high (~4.2V). We recommend trying your juices at the low setting (green) first as this is also the most energy efficient and will provide the longest battery life between recharges. The "normal" setting is 3.6V (blue).

Variable voltage using Twist Nob at the bottom - VV Twist / Vision Spinner / Aspire CF Batteries

IMPORTANT: Only use the eCigWorld supplied 420mA charging lead and USB plug. Using other chargers may damage the device and create a fire risk.

Please fully charge the battery before use.

Ensure the battery’s connector is dry and clean before connecting to the charger. The battery is connected to the charger by screwing it into the device. Take care not to cross the thread or over-tighten.

NOTE: Over-tightening chargers, clearomizers and atomizers can damage a battery. Carefully screw on

these components until you begin to feel resistance; then apply a maximum further one-quarter turn.

The battery will take 3.5 - 4.5 hours to recharge from flat using the USB wall plug. We strongly recommend the use of the USB wall plug.

Variable voltage Twise batteries have a nob dialer at the bottom of the battery which can be turned/twisted to set it at desired voltage setting These batteries are lot easier to change the voltage setting. Vision Spinner, Spinner 2, Aspire CF VV, Aspire CF VV+ have twist dialer.



The battery includes IC (integrated circuit) protection on the PCB (Printed Circuit Board), which prevents over discharge, over charge and over current. The battery charger lead will automatically switch to standby (green) once the appropriate voltage has been reached.

Please note that the USB wall plug LED will remain the same colour, regardless of charging stage. The wall plug also contains safety features in its circuitry.

Regardless of the safety features, a charging battery is a fire risk. You should not leave a charging battery unattended and the battery should be removed from the charger as soon as the cycle is complete.

Changing atomizer heads

The atomizer head inside the clearomizer should last a couple of weeks under fairly consistent use. Once vapour production decreases or juices start tasting a little odd; it’s a good sign the head needs changing. Spare heads are available from eCigWorld. The head change is a simple process:

Unscrew the bottom hardware, then unscrew the coil head from the bottom hardware and replace with a fresh coil head

IMPORTANT: General care

Like any electronic device with a lithium battery, some basic safety precautions should be taken; with some extra points with regard to vaping equipment. Don’t hesitate to contact us for clarifications.

Only use the eCigWorld charging lead specific to your battery and AU approved wall plugs.

Keep the battery dry and clean the battery connector with a cloth before charging.

Do not expose to extreme heat - such as leaving in the car on a hot summer’s day. Never charge a battery unattended and check battery regularly while charging.

If battery becomes hot when charging, remove from charger immediately and contact us.

Remove battery from charger as soon as charging cycle is complete.

Do not use cartomizers, clearomizers and modifications not suited to the battery.

Only use standard resistance cartomizers and clearomizers

Batteries should be rested for an hour after charging.

Avoid dropping a battery and do not subject it to other forms of shock. Use the battery button lock when not in use. More performance and safety tips available at www.eCigWorld.com.au.

How to use Kanger Protank and Aerotank Clearomizer e-cigarette. a. How to change coil head: Step 1:Unscrew the Kanger Protank glass tube from bottom base .

Step 2: Unscrew the old Kangertech Protank coil head from the top of the base assembly.

Step3: Screw the new Kangertech Protank coil head into the bottom base again;

* Tips: A loose coil head can cause leaking. And too tight coil head can damager battery head/contact Step4: Screw the Kanger Protank glass tube back into the bottom base.

b. How to fill e-liquid to the Kanger Protank glass clearomiser: Step 1: Take out the e-liquid bottle lid; Step 2: Cut off the top of bottle;

Step 3:Unscrew the Protank bottom base from the glass tube.

. Step 4:Fill the e-liquid to the Kanger Protank glass tube. Using an eliquid bottle or syringe, fill the Protank glass tube by inserting e-liquid down the side wall (Do not fill e-liquid in the center hole, that is for air flow).

Step 5: Screw the Kanger Protank bottom base back into the glass tube again.

* Tips: the protank coil head may be loosed with the bottom base, if so, please re-screw it in the bottom base again. c. How to enjoy your Kanger Protank e-cig : Screw filled protank glassomizer with the eGo battery, then will be stand-by state.

* Activate the battery by click the button 5 times. It will turn the battery ON (To Turn it OFF press the button 5 times). Once battery is on, it will fire every time button is pressed. Now to start vaping press the LED button and inhale at the same time. d. How to charge the Kanger Protank battery: You just screw the eGo battery with the USB charger, then plug it into the PC or AC-USB Adapter. 1. the first charge should be kept for 8 hours, even if the LED light turns green. 2. Use for 20 minutes., 3. Charge the battery for another 1 hour. Your eGo battery is ready for normal using now. The normal charging time should be kept for 3 hours( even if the LED light turns green).

e. Tips of the Kanger Protank clearomizer (glassomizer) e-cig: 1. A loose Kangertech Protank coil head can cause leaking and poor contact. 2. Kangertech Protank coil heads have an average lifespan between 7 to 15 days (sometimes longer). A coil head should be replaced when it begins to leak, produce less vapour, taste bad and/or stop working entirely. 3. It is not uncommon for the coil head to become loose after refilling the clearomizer a few times. It is good practice to check the coil head to ensure that it is tight when filling. 4. It is normal to find a small amount of liquid in the eGo battery contact area when removing the Clearomizer or any atomizer. The eGo battery should be cleaned out with a paper towel or tissue before charging. 5. Ensure that the Kangertech Protank base is tightly connected to the tank or leaking can occur. 6. Try to keep the tank full of E-Liquid ("topped off"). This helps maintain the "vacuum" in the tank and prevent leaks/gurgling. f. How to clean Kangertech Protank glassomizer/coil heads: Step 1: Take off the Kangertech Protank coil head atomizer from the Protank. Step 2: Put the Kangertech Protank coil head in the alcohol for 24 hours. Step 3: Take off the Kangertech Protank coil head from the alcohol and fling it, thrown away the alcohol. Step 4: Put it in the Kangertech Protank coil head again, the cleaning has been finished.



Warning:

eCigWorld products are not intended for non-smokers and we recommend medical supervision when using vaping products. Our products are not intended for use by children, pregnant or breastfeeding women, persons with or at risk of heart disease, high blood pressure or diabetes. If you have allergies or sensitivities to any type or combination of inhalants or are taking any sort of medication, consult professional medical advice before commencing use of vaping products.

If you should experience any difficulties with your equipment, we want to know about it. Please don’t hesitate in contacting us via the eCigWorld.com.au web site – our goal is to have happy customers J.

ecigworld kanger starter kit manual

Documents