eclipser 2000 - encore fasteners – encore fasteners€¦ · 03/10/2018 · 30040 spring 20038...
TRANSCRIPT
SAFETY INFORMATION
READ THE ENTIRE MANUAL BEFORE OPERATING THE TOOL.
SAFETY GLASSES should always be worn while operating, maintaining or repairing a tool.
KEEP HANDS AND FINGERS AWAY from the blade and anvil area when operating or
connecting air supply to tool.
DISCONNECT THE AIR SUPPLY when mechanically clearing a jam, performing
maintenance or repairs, and whenever the tool is not in use.
Never use oxygen, carbon dioxide or any other bottled gas as a power source for this
tool—the tool will explode and cause serious injury.
INJURY PREVENTION—Never point the tool toward yourself or anyone else.
ENCORE (EA) ECLIPSER 2000 SERIES Pneumatic Clipping Tool GREEN Housing GREEN Clip Magazine
HARTCO (HR) ECLIPSER 2000 SERIESPneumatic Clipping Tool BLACK Housing BLACK Clip Magazine
Compatible with Encore E-Clips, Hartco clips and other industry standard clips
Eclipser 2000and Optional Hanger Assembly
[email protected], IL 60062 U.S.A.Phone: (224) 723-5524Fax: (224) 723-5526
MADE IN THE U.S.A.
Optional Hanger Assembly
Thin (“T”) Models for Trap and Cage Assembly
Hartco Eclipser 2000 Series(Black)
Encore Eclipser 2000 Series (Green)
Revised 2018-10-03
30011TRIGGER
30021 PIN, BLADE
30004PISTON
30005 SPRING
20011SCREW
SEE CHART ON PAGE 3
20021 NUT
30040SPRING
20038 SHCS
30012SIDE PLATE R. H.
20012NUT
30022FRONT PLATE
30023SHOULDER SCREW
20004O-RING
20036 C-CLIP
30006GROOVED PIN
30010 LEVER
30009 SLEEVE
20007 O-RING
30008 VALVE
30007 SPRING
20006 O-RING
20005O-RING
30051 PUSHER “A”
20034 SCREW
30029PUSHER PULL
30017 YOKE
30018 ROLLER
30019 LINK
30020 PIN, ROLLER
20018 PIN
20008BHCS
20009 PIN
30015 PIN
30014TOP PLATE
30016SPRING
30013 SIDE PLATE L. H.
30000 VALVE
20003 O-RING
20000 O-RING
20001 O-RING
20019 PLUG
20035 PLUG (RED)
20011 SCREW
30001 CAP
15316 SCREW
55095HANGER YOKE
20037 E-CLIP
30130 HANGER
30033HANGER PIN
15037 BEARING
20012 NUT
20065SCREW
20036C-CLIP
20010 PIN
30002 HOUSING (GREEN) 35002 HOUSING (RED)38002 HOUSING (BLACK)
BLADEGUIDE
SEE CHART ON
PAGE 3
BLADESEE CHART
ANVILSEE CHART
PUSHER with Latch
SEE CHART ON PAGE 3
MAGAZINE
30041PIN
20037 E-CLIP
Thin “T” Models
20037 E-CLIP
Standard
Thin “T”
2018-10-03www.encorehartco.comStandard Models
30131 Hanger Assembly 115037 Bearing 115316 Screw 120012 Nut 120036 C-Clip 120037 E-Clip 120065 1/4-20 3/8” Flange Head 130033 Hanger Pin 130130 Hanger 155095 Hanger Yoke 1
Item # Description Qty
2The Eclipser 2000 Series
Note: Models 2000-1533 and 2000-4528 use
Part #30056
3
2000-1020 30210 30220 30202 30050 38050 30051 A2000-1020S 30210 30220 30203 30050 38050 30051 A2000-1022 30210 30222 30201 30050 38050 30051 A2000-1024 30210 30224 30208 30050 38050 30051 A2000-1121 30211 30221 30201 30050 38050 30051 A2000-1234 30212 30234 30254 30050 38050 30049 A2000-1533** 30215 30233 30255 30050 38050 30051 A2000-1926 30219 30226 30203 30050 38050 30051 A2000-1929 30219 30229 30203 30050 38050 30051 A2000-3236 30232 30236 30207 30024 38024 30031 E2000-4050 30240 30250 30205 30024 38024 30030 F2000-4139 30241 30239 30209 30024 38024 30031 E2000-4151T* 30241 30251 30205 30024 38024 30035 F2000-4157T* 30241 30257 30204 30060 38060 30035 F2000-4528** 30245 30228 30256 30050 38050 30051 A2000-6075 30260 30275 30200 0 30024 38024 30025 F, H2000-6080 30260 30280 30200 0 30024 38024 30025 F, H2000-6082 30260 30282 30200 0 30024 38024 30025 F, H2000-6181 30261 30281 30200 0 30024 38024 30025 F, H2000-6181T* 30261 30281 30200 0 30024 38024 30035 F, H2000-6183 30261 30283 30200 1 30024 38024 30025 F, H2000-6183T* 30261 30283 30200 1 30024 38024 30035 F, H2000-6185 30261 30285 30200 0 30024 38024 30025 F, H2000-6187T* 30261 30287 30200 1 30060 38060 30035 F, H2000-6189 30261 30289 30200 1 30024 38024 30025 F, H2000-6788 30267 30288 30206 30060 38060 30025 F, H2000-6791T* 30267 30291 30206 30060 38060 30035 F, H2000-6794 30267 30294 30302 30061 38061 30025 F, H
Magazine Fits Blade
Pusher Clip Model Anvil Blade Guide GREEN BLACK w/Latch Width
0 Indicator (visible from back of tool) shows required orientation for Part #30200 in tool.
ECLIPSER 2000 PARTS IdENTIfICATIONTo better serve our customers, we regularly add new models and make refinements to parts. For the most up-to-date manual and parts listing, visit encorehartco.com and click on the SUPPORT tab.
SAfETY CAUSE SOLUTIONBlade does not Sticky valve Lubricate main valve and check return that main valve piston moves
Dirty #3000 valve 1/32” hole must be clear
Loose screw in housing cap Tighten all 4 screws in cap
Sluggish tool Dry main valve Lubricate main valve
Clips not feeding Obstruction in magazine Remove obstruction
Broken pusher spring Replace pusher spring
Loose clips Low air pressure Increase pressure to 80 psi
Worn blade or anvil Replace blade or anvil
Clip jamming Clips are loaded backward Reorient strip so that single ear into the magazine on clip is loaded forward
Tool not cycling Clogged trigger valve Clean trigger valve assembly
WEIGHT: 4.4 lbs (2.0 kg)
dIMENSIONS: 16.5” x 7” x 4” (419.1 x 177.8 x 101.6mm)
COMPONENT MATERIALS: Composite plastic housing and clip magazine
CLIP fEEdING METHOd: Constant force spring
PRIMARY POWER UNIT: Main cylinder - Bore 3.06” (78mm) spring return
AIR SUPPLY: 80-90 psi (5.5-6.2 bars) of dry, lubricated air
AIR CONSUMPTION (SCfM): 3.56, assuming 90 psi and 1 cycle per second 3.22, assuming 80 psi and 1 cycle per second
20000 O-Ring 120001 O-Ring 120003 O-Ring 120004 O-Ring 120005 O-Ring 120006 O-Ring 120007 O-Ring 120008 BHCS 220009 Dowel Pin 120010 Dowel Pin 220011 SHCS 620012 Nut* 220018 Dowel Pin 120019 Plug 120021 Nut 120034 Screw 220036 C-Clip 120035 Plug (Red) 120037 E-Clip* 420038 SHCS 130000 Valve 130001 Cap 130002 Housing, GREEN
135002 Housing, RED38002 Housing, BLACK
Item # Description Qty Item # Description Qty
* Tools with a “T” have a narrow clipping head. On those tools: - Part #20037 (E-Clip) is used instead of Part #20012 (Nut) - Part #30041 (Pin) is used instead of Part #30023 (Shoulder Screw)
** Models 2000-1533 and 2000-4528 use Front Plate #30056. All other models use Front Plate #30022.
ANVIL NUMBER (AA) LOCATED ON BACK OF ANVIL
BLADE NUMBER (BB) LOCATED UNDER FRONT PLATE. TO FIND, PRESS IN PIN AND SLIDE THE COVER UP.
XXXXX
MODEL NUMBER = 2000-AABB
PIN
5-DIGIT SERIAL
NUMBERXXXXX
NUMBER /ARROW ON BLADE GUIDE
VISIBLE HERE
2018-10-03
30004 Piston Assy. 130005 Compression Spring 130006 Grooved Pin 130007 Spring 130008 Trigger Valve 130009 Valve Sleeve 130010 Trigger Lever 130011 Trigger Assy. 130012 Side Plate, R. H. 130013 Side Plate, L. H. 130014 Top Plate 130015 Pin 130016 Spring 130017 Yoke 130018 Roller 130019 Link 230020 Pin, Roller 130021 Pin, Blade 130022 Front Plate** 130023 Shoulder Screw* 230029 Pusher Pull 130040 Spring 130041 Pin* 2All other parts are model specific and are listed in the chart at right.
RECOMMENdEd dAILY MAINTENANCEAdd 2-3 drops of air tool oil (10-weight recommended) to air inlet hose fitting (A); and openings between the side plates at these two locations:
• inthegapatthebackofthetopplateandthehousing (B)
• theopeningonthefrontplate(C), as shown on affixed label
3
PARTS REPLACEMENTBLAdE: dISCONNECT AIR. REMOvE CLIPS fROM TOOL.
1. Depress pin (I) at top of front plate (J); slide plate up and remove.
2. Swing blade (L) from tool and align link pin (K) with holes in both side plates. Remove pin through holes and take out old blade.
3. Lubricate new blade.
4. With new blade at 90° angle, align blade hole with links (Part #30019)and side plate holes on both sides. Insert link pin (K) through aligned holes to secure blade. Firmly strike blade face to swing back into original position.
5. Re-lubricate front plate. Depress pin (I) and slide front plate down until pin is released, securing plate in place.
ANvIL: dISCONNECT AIR. REMOvE CLIPS fROM TOOL.
1. Remove lower shoulder screws (M) or pins/e-clips if tool is a “T” model.
2. Remove old anvil (N) and replace.
PUSHER SPRING: dISCONNECT AIR. REMOvE CLIPS fROM TOOL. For better access, turn tool upside down.
1. Loosen screw (R) with a 9/64" hex key and remove damaged pusher spring from magazine. Insert new spring (S) into back of pusher (P).
TOOL OPERATION1. Connect air supply to air inlet hose fitting (A), keeping fingers and
hands away from blade and anvil area. Recommended air supply is 80-90 psi (5.5–6.2 bars) of dry, lubricated air.
Eclipser air consumption (SCFM), assuming 90psi and 1 cycle per second, is 3.56. Assuming 80psi and 1 cycle per second, SCFM is 3.22.
2. Load clips into magazine.
3. Set wires to be fastened into side plate notches (d). For best results, smaller wire should be on the bottom. Squeeze trigger (E) to install clip.
LOAdING CLIPS 1. Pull pusher (f) back until it latches at the end of magazine (G).
2. Remove strip of clips from box. Load entire strip into magazine with the single “ear” facing towards the front of the tool.
3. Secure clips in place by depressing pusher latch on underside of magazine.
www.encorehartco.com • [email protected], Illinois 60062 U.S.A.Phone: (224) 723-5524 • Fax: (224) 723-5526
U
2. Pull spring out from pusher with fingers or by using the screw.Align the spring hole with the magazine screw hole. Insert screw and secure with nut (U). Be careful not to deform spring.
3. Pull pusher back and latch at end of magazine.
2018-10-03
1
2
RS
P
4
F
SINGLE EAR FACES FRONT OF
TOOL
SMALLER wIRE ON BOTTOM
E
puShERLATCh
CLIPS
G
D
AC
TO GET STARTEdInstall a ¼” NPT fitting (not included) into air inlet opening in the back of the housing, using suitable thread sealant. DO NOT REMOVE RED PLUG LOCATED ABOVE THIS OPENING.
B
I
ANVILM
BLADEL
DIRECTION ShOwN TO
REMOvE pART(S).
REvERSE TO puT IN NEw
pART
N
K
J