ecosmart 250w en
DESCRIPTION
Ecosmart 250W goboprojector manualTRANSCRIPT
Goboservice Lighting by Sunland Optics SRL Via Gaspare del Fosso 33, 89127 Reggio Calabria
+39 0965 813264 Via Lombardia 269, 20047 Brugherio (MB)
+39 02 23166538 www.goboservice.com [email protected]
INSTRUCTIONS, USE
AND MAINTENANCE
MANUAL FOR ECOSMART PROJECTOR
BEFORE USE
This fixture must be operated only by adults.
Unpack the content from the box and check whether there are any damages caused by transportation.
Make sure that voltage and frequency in your area are the same the projector is certified to operate within.
You must connect the projector to a grounded wall socket.
Make sure there are no inflammable materials around the projector.
Put the projector in a place with good airflow. Do not use the projector in closed or semi-closed environments that
might increase the working temperature, thereby reducing the life of the unit.
The ambient temperature should not exceed 30°C.
INTRODUCTION
Read carefully the following instructions before any operation. The product described in this manual is a lighting
fixture for projecting a luminous beam. It is normally employed to illuminate, with a high level of brightness, small
areas that must be emphasized. The projector can be used to create luminous effects for decorative purposes. The
fixture must be used only for the purposes for which it has been designed and built. It is aimed to indoor and
outdoor lighting, every other use is not approved by the manufacturer and therefore it frees him from any
responsibility for damages deriving from improper or uncorrect use. This unit should be disposed of according to your
country’s regulations regarding the differentiated waste collection and disposal.
CLAUSES
This instructions manual must accompany the fixture. This manual must be stored carefully for at least 10 years, in a
place known by all the concerned persons. This manual has been written accordingly to the EU directives 2006/95/EC
and 2004/108/EC. The safety instructions contained in this manual cannot exclude other situations where the
product may result dangerous. Remember always to pay attention and to be careful when dealing with the product.
FOREWORD
For a proper use of the product, please follow these user's instructions to avoid damages to the product and to the
user. The aim of this manual is to inform you about installation, use, safety and maintenance. The manual does not
give only a description of the fixture, but it gives also useful advice in order to guarantee the maximum efficiency.
Since the knowledge of the manual is very important when dealing with emergencies, it must be read carefully
before using the product and must be consulted everytime difficulties or doubts should arise.
INSTALLATION AND USE
After undertaking the aforementioned checks, the user can install the projector. The installation must be executed
exclusively by qualified staff. The fixture must be fixed to wall with dowels, screws or other type of suitable
elements. After fixing the unit, you can connect it to the wall socket (you must connect it to a grounded wall socket).
Please follow the standard safety measures concerning any electrical appliance.
Caution ! never connect the projector to the wall socket when the installation is still taking place
Caution ! when the projector is connected to the wall socket, avoid any contact with water or humid surfaces or
moisture
After installing the fixture and connecting it to the ground, the unit can be switched on. If the lamp does not start or
there is a significant flicker, disconnect the unit from the wall socket before any action. The user is not allowed to
dissasemble the projector or to carry out any action on the electric part of it.
The projector's purpose is the projection of logos, texts, pictures. Should you see any cracks or breaks in the
housing, stop using the product immediately. Do not install the projector in a place where there are people or crowd
passing by. The fixture, if disconnected from the wall socket, is not harmful even when wet or under the rain.
The fixture works with low woltage AC and is as dangerous as a normal household appliance. The projector has been
designed according to all the available criteria of safety and has been built using materials fit for preventing dangers
and minimizing risks, but behave responsibly during use.
The projector is for indoor use only and should be kept away from moisture.
The projector gets very hot during use: avoid contact with the naked skin to prevent burns. You should wear gloves
when touching it.
When the projector is turned on, do not touch the housing or the cables and avoid watching in the lamp’s direction.
Before doing any maintenance on the unit, you must:
• switch off the unit and unplug it from the wall socket.
• wait 15 minutes before opening the housing.
After turning off the projector, wait 5-10 minutes before turning it on again, to avoid damages to the lamp.
If you need replacing the lamp, the engine or the ballast, please contact your reseller for genuine spare parts.
Never disassemble the projector or replace the faulty parts with non-genuine ones.
RESDIUAL RISKS
Even if the fixture has been built according to all laws and regulations, there is still some risk due to some structural
and functional aspects of the fixture. Do not disassemble the unit, and all maintenance operations must be carried
out only by specialized staff. The ballast is sealed for safety reasons and it should never be opened. Warranty is void
if the ballast seal is broken. Please put the projector in a place that can be easily seen by other people, to avoid
them stumble upon it. Avoid installing the unit in a place where it might fall from, hurting people underneath. Keep
children away at all times when the unit is switched on or when it is plugged to the wall socket.
MAINTENANCE
The only maintenance operation you can undertake is the cleaning of the unit, which must not be washed but only
cleaned with a soft damp cloth. Never clean the unit when it is switched on or when it is plugged to the wall socket.
GOBO SUBSTITUTION
To substitute the gobo:
1. Switch off the projector and disconnect it from the wall socket.
2. Wait 15 minutes before opening the housing.
3. Unscrew the 8 screws on the front of the projector and remove it.
4. Take out the gobo-holder and unscrew the ring as shown below.
6. Put the gobo in the place shown below.
6. Screw the ring back in place around the gobo and re-insert the gobo-holder inside the projector.
7. Screw the projector’s front with the 8 screws available.
FOCUSING
To set the focus you only need to turn the ring around the lens, on the projector’s front.
LAMP REPLACEMENT
Replace the old lamp only with one of the same kind. Do not exceed the maximum supported voltage.
To install a new lamp:
1. switch off the projector and disconnect it from the wall socket.
2. wait 15 minutes before opening the housing.
3. unscrew the 8 screws on the front of the projector and remove it.
4. move the gobo-holder until the end of the rods and take it out from the projector.
5. Gently pull the lamp in your direction with a gloved hand. The lamp’s bulb should not be touched with your bare
hands. Should it happen, clean it with an alcohol-soaked cloth.
6. Insert the new lamp.
7. put the gobo-holder back inside, sliding it on the rods towards the lamp.
8. screw the front of the projector back in place with the 8 screws available.
REPLACEMENTS
Any replacement or substition must be carried out only by specialized staff. For any maintenance operation, please
contact your reseller.
CE MARKING
The projector described in this manual has been designed and built according to EU Directives 2006/95/EC (low vol-
tage) and 2006/95/EC (electromagnetic compatibility). This is confirmed by the CE mark on the product and by the
Declaration of Conformity at the end of this manual.
WASTE DISPOSAL
This unit should be disposed of according to your country’s regulations regarding the differentiated waste collection
and disposal.
WARRANTY
Our products have a 24-month warranty. We will, at our own choice, repair or replace your product. We need an
adequate amount of time for the operations required and for the spare parts delivery. All the costs for shipping the
parts to be replaced are charged on you. Unauthorized servicing or repairing voids the warranty. Only the original
purchaser can benefit the warranty. We are not subject to the warranty when the original purchaser resells the
product, the product is modified or any parts not produced by us are added to the product. Warranty does not cover
damages caused by excessive strain, such as after realizing there is an anomaly caused by misuse, improper
maintenance, or ignoring the use instructions. We are not responsible for any difficulties that might arise when
reselling the product or using it abroad in the country when it has been sold.
Should you need to use the warranty, please tell us the following information:
• Date of purchase
• Detailed description of the problem
The unit has been delivered to you in perfect conditions. All users are required to follow strictly the safety instructions and
the notes contained in this manual. Any damage caused by the disregarding of the manual voids the warranty. We are not
responsible for damages or problems caused by the disregarding of the manual.
Any servicing or repairing must be undertaken only by the manufacturer. We are not responsible for damages caused by
unauthorized servicing or repairing. Unauthorized total or partial disassembling of the projector voids the warranty. Spare
parts such as lamps or fuses are not covered by the warranty.
We have the right to modify the manual’s content, anytime and without notice.
Pictures shown are for illustration purpose only.
IMPORTANT
Pictures shown are for illustration purpose only. Actual product may vary due to product enhancement.
I, the undersigned, Mario Suraci, born in Vibo Valentia (Italy) on 2
March 1962 and resident in Reggio Calabria, Via Pio XI diramazione
Gullì n°34/C
as the legally authorized representative of Sunland Optics SRL, establi-
shed in Reggio Calabria, Via S.Anna II° Tronco n°28,
DECLARE
that the Eco Smart 250W projector
Serial Number:
has been built in accordance with the following EU directives:
2006/95/EC (low voltage)
2004/108/EC (electromagnetic compatibility)
and so it complies with the law in force.
Reggio Calabria, 21 May 2010
(Ing. Mario Suraci)
DECLARATION OF CONFORMITY