eduard jas-39d gripen twin seater self adhesive · 2013. 5. 22. · jas-39 gripen twin seater...
TRANSCRIPT
14B
(25A)
(26A)
25B
26B
7B (7A)
10
11
1
2
5
5
3
6
4
4
18
1/48 scale detail set for kit •sada detailů pro model 1/48ITALERI ITALERI
JAS-39D Gripen twin seater self adhesive
FE382
eduard
REMOVEODSTRANIT
OPTIONVOLBA?
REPLACENAHRADIT
BENDOHNOUT
GRINDOBROUSIT
SYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽ
DRILL HOLEVRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PŘED SLEPENÍM
ORIGINAL KIT PARTSPŮVODNÍ DÍLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTANÉ DÍLY
PARTS TO BE REMOVEDDÍLY K ODSTRANĚNÍ
FILLTMELIT
1/4 FE 382
film
FE 382 + 49 382JAS-39 Gripen
twin seater
REFERENCES:www.39gripen.cz
MODEL FAN #10/2001 (POLAND)
MODEL MAGAZIN #2/1999 (SLOVAKIA)
41B
43A
1A
17A
41A
21
22
4,0mm
5B
41B
film
front instrument panel
5B
14
12
7
23
2/4 FE 382
43A
41B20
19
14A
rear instrument panel
correct positioncorrect position
5A
17
13
41A
correct position
17A1A
15
16
front instrument panel
8
9
filler
2,0mm
43A
17A
1A24, 25
2425
2,0mm
rearinstrument
panel
© EDUARD M.A. 2007 Made in Czech Republicwww.eduard.com
3/4 FE 382
2. Do not inadvertently place etched componets on anunwanted surface. Attempts to remove will result indamage to your part.
2. Nepokládejte samolepící díly na volné plochy. Pokudje omylem přilepíte, při pokusu o odlepení dojde kpoškození dílu.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na části dílů, na kterých je naneseno lepidlo.
1. Separate the etched components from their frames on theprotective paper. Removal from the paper is done only afterseparation of the parts from the frames.
1.Samolepící díly oddělujte od rámečku na podkladovémpapíře. Po oddělení je sejměte z krycího papíru.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za části, na kterýchnení nanesené lepidlo.
5. Lightly place the component in the desired location andposition. Adjust as required. The component will bypermanently affixed when pressed onto its intendedlocation, its location can be adjusted.
5. Díl lehce položte do pozice, ve které má být nalepen.Upravte přesnou pozici a přimáčkněte. Díl dokonale přilneaž po přimáčknutí, před přimáčknutím lze dílem opatrněmanipulovat.
1/48 scale detail set for kit •sada detailů pro model 1/48ITALERI ITALERI
JAS-39D Gripen twin seater self adhesive
4/4 FE 382
1/48 FE 382 + 49 382 JAS-39 Gripen twin seater
© EDUARD 2007 Made in Czech Republic
1 2
3 4
5 5 6 6
6 6 5 5 4 3 2 1
7
8 9
10 11
12
13
14
15
16
17
181920
2122
23
24
25