ego thermostat bath & shower set tx449se - toto… · "ego" thermostat bath &...

1
4.CERAMIC HEAD WORK 1. AERATOR 2. FILTER 5. BOLT 6. BOLT 3.NUT SPECIFICATIONS OPERATING CONDITIONS S06219S TROUBLESHOOTING "EGO" THERMOSTAT BATH & SHOWER SET TX449SE TX449SEN "EGO" Thermostat Bath & Shower Set INSTALLATION MOUNT CONNECTORS PARALLEL WITH THE WALL 1 3 5 A0905 OPTIONAL SHOWER TYPE SHOWER D1205QMFT1 A0905 Cover Spout Filter Body CHECK POINT Flow rate unsatisfactory 1, 2 Remove and clean Water leaks around the handle Tighten PROBLEM SOLUTION Handle is loose 5, 6 Tighten 3, 4 Flexible Hose w/ Packing Screw Hanger Hand Shower 150±20 150 Hot Water Supply Cold Water Supply Leg 2 4 Adjust the number 40º on the handle with mark line in the body, then install the handle If get the water temperature at 40ºC, release the handle. Make sure the spindle not rotated. 6 40 Mark Line Handle Spindle Bolt Handle 40 o C Safety Knob Open full the stop valve and check the water temperature 40ºC. When water temperature not 40ºC , set the water temperature until get 40ºC then follow step 5 and 6. 2 X Ø8 Holes TX449SEV1N "EGO" Thermostat Bath & Shower Mixer w/o Hand Shower Set MAINTENANCE Always wipe chrome plated area with dry soft cloth, and sometimes wipe it with cloth soaked in mild soap. TX449SEV2Z "EGOII " Thermostat Bath & Shower Set _ MARK Sleeve Anchor 171 42° Ø8 20 40 55 47 Ø50 215.5 0 -7 PJ ½ 150±20 228 0 -7 D1205QMFT1 Cap ALIGN WITH MARK OPEN O-Ring R4 Bolt Washer Cap Washer ATTENTION 1. Use of abrasive cleaning material such as; detergents containing hydrochloric acids, thinner, polishing powder, and nylon brush is not recommended. 2. Press safety knob turn left to increase temperature over 40 o C. 3. Please don't open the thermostat cartridge, because it cause to unstabilize temperature in this product. 4. Flow Regulator should not be remove because it could damage the system 1. Water supply pressure : 0.05 ~ 0.75 MPa. Hot water supply temperature shall be higher by 10 o C. at least, than desired temperature of mixed water. (Recommendation: Hot water supply temperature =60 o C) Hot water supply pressure shall be the same or lower than cold water supply . Ensure that water supply is clean (No Sand, Dirt, Etc.). 2. 3. 4. Flow Regulator Inside (Don’t remove) Rain Spray Button Massage Spray Button

Upload: haphuc

Post on 31-Aug-2018

303 views

Category:

Documents


1 download

TRANSCRIPT

Page 1: EGO THERMOSTAT BATH & SHOWER SET TX449SE - toto… · "EGO" THERMOSTAT BATH & SHOWER SET TX449SE TX449SEN "EGO" Thermostat Bath & Shower Set ... "EGO T h erm os taB & SwMix / H nd

4.CERAMIC HEAD WORK

1. AERATOR

2. FILTER

5. BOLT

6. BOLT

3.NUT

SPECIFICATIONS

OPERATING CONDITIONS

S06219S

TROUBLESHOOTING

"EGO" THERMOSTAT BATH & SHOWER SET TX449SE

TX449SEN"EGO" Thermostat Bath & Shower Set

INSTALLATION MOUNT CONNECTORS PARALLEL WITH THE

WALL

1

3

5

A0905

OPTIONAL SHOWER

TYPE SHOWERD1205QMFT1

A0905

Cover

Spout

Filter

Body

CHECKPOINT

Flow rate unsatisfactory 1, 2 Remove and cleanWater leaks around the handle Tighten

PROBLEM SOLUTION

Handle is loose 5, 6 Tighten3, 4

Flexible Hosew/ Packing

Screw

Hanger

Hand Shower

150±20

150

Hot Water

Supply

Cold Water Supply

Leg

2

4

Adjust the number 40º on the handle with mark line in the body, then install the handle

If get the water temperature at 40ºC, release the handle. Make sure the spindle not rotated.

640

Mark LineHandle

Spindle

Bolt

Handle

40oC

Safety Knob

Open full the stop valve and check the water temperature 40ºC. When water temperature not 40ºC , set the water temperature until get 40ºC then follow step 5 and 6.

2 X Ø8 Holes

TX449SEV1N"EGO" Thermostat Bath & Shower Mixer w/o Hand Shower Set

MAINTENANCEAlways wipe chrome plated area with dry soft cloth, and sometimes wipe it with cloth soaked in mild soap.

TX449SEV2Z"EGOII " Thermostat Bath & Shower Set

_

MARK

Sleeve Anchor

17142°

Ø8

20

40

5547

Ø50

215.5 0-7

PJ ½150±20

228 0 -7

D1205QMFT1

Cap

ALIGN WITH MARK

OPEN

O-Ring

R4

BoltWasher

Cap

Washer

ATTENTION1. Use of abrasive cleaning material such as; detergents containing hydrochloric acids, thinner, polishing powder, and nylon brush is not recommended.2. Press safety knob turn left to increase temperature over 40oC.3. Please don't open the thermostat cartridge, because it cause to unstabilize temperature in this product.4. Flow Regulator should not be remove because it could damage the system

1. Water supply pressure : 0.05 ~ 0.75 MPa.Hot water supply temperature shall be higher by 10oC. at least, than desired temperature of mixed water. (Recommendation: Hot water supply temperature =60oC)Hot water supply pressure shall be the same or lower than cold water supply .Ensure that water supply is clean (No Sand, Dirt, Etc.).

2.

3.

4.

Flow Regulator Inside (Don’t remove)

Rain Spray Button

Massage Spray Button