ego thermostat bath & shower set tx449se - toto … · "ego" thermostat bath & shower set tx449se...

of 1 /1
4.CERAMIC HEAD WORK 1. AERATOR 2. FILTER 5. BOLT 6. BOLT 3.NUT SPECIFICATIONS OPERATING CONDITIONS S06219S TROUBLESHOOTING "EGO" THERMOSTAT BATH & SHOWER SET TX449SE TX449SEN "EGO" Thermostat Bath & Shower Set INSTALLATION MOUNT CONNECTORS PARALLEL WITH THE WALL 1 3 5 A0905 OPTIONAL SHOWER TYPE SHOWER D1205QMFT1 A0905 Cover Spout Filter Body CHECK POINT Flow rate unsatisfactory 1, 2 Remove and clean Water leaks around the handle Tighten PROBLEM SOLUTION Handle is loose 5, 6 Tighten 3, 4 Flexible Hose w/ Packing Screw Hanger Hand Shower 150±20 150 Hot Water Supply Cold Water Supply Leg 2 4 Adjust the number 40º on the handle with mark line in the body, then install the handle If get the water temperature at 40ºC, release the handle. Make sure the spindle not rotated. 6 40 Mark Line Handle Spindle Bolt Handle 40 o C Safety Knob Open full the stop valve and check the water temperature 40ºC. When water temperature not 40ºC , set the water temperature until get 40ºC then follow step 5 and 6. 2 X Ø8 Holes TX449SEV1N "EGO" Thermostat Bath & Shower Mixer w/o Hand Shower Set MAINTENANCE Always wipe chrome plated area with dry soft cloth, and sometimes wipe it with cloth soaked in mild soap. TX449SEV2Z "EGOII " Thermostat Bath & Shower Set _ MARK Sleeve Anchor 171 42° Ø8 20 40 55 47 Ø50 215.5 0 -7 PJ ½ 150±20 228 0 -7 D1205QMFT1 Cap ALIGN WITH MARK OPEN O-Ring R4 Bolt Washer Cap Washer ATTENTION 1. Use of abrasive cleaning material such as; detergents containing hydrochloric acids, thinner, polishing powder, and nylon brush is not recommended. 2. Press safety knob turn left to increase temperature over 40 o C. 3. Please don't open the thermostat cartridge, because it cause to unstabilize temperature in this product. 4. Flow Regulator should not be remove because it could damage the system 1. Water supply pressure : 0.05 ~ 0.75 MPa. Hot water supply temperature shall be higher by 10 o C. at least, than desired temperature of mixed water. (Recommendation: Hot water supply temperature =60 o C) Hot water supply pressure shall be the same or lower than cold water supply . Ensure that water supply is clean (No Sand, Dirt, Etc.). 2. 3. 4. Flow Regulator Inside (Don’t remove) Rain Spray Button Massage Spray Button

Author: others

Post on 07-Apr-2020

9 views

Category:

Documents


0 download

Embed Size (px)

TRANSCRIPT

  • 4.CERAMIC HEAD WORK

    1. AERATOR

    2. FILTER

    5. BOLT

    6. BOLT

    3.NUT

    SPECIFICATIONS

    OPERATING CONDITIONS

    S06219S

    TROUBLESHOOTING

    "EGO" THERMOSTAT BATH & SHOWER SET TX449SE

    TX449SEN"EGO" Thermostat Bath & Shower Set

    INSTALLATION MOUNT CONNECTORS PARALLEL WITH THE

    WALL

    1

    3

    5

    A0905

    OPTIONAL SHOWER

    TYPE SHOWERD1205QMFT1

    A0905

    Cover

    Spout

    Filter

    Body

    CHECKPOINT

    Flow rate unsatisfactory 1, 2 Remove and cleanWater leaks around the handle Tighten

    PROBLEM SOLUTION

    Handle is loose 5, 6 Tighten3, 4

    Flexible Hosew/ Packing

    Screw

    Hanger

    Hand Shower

    150±20

    150

    Hot Water

    Supply

    Cold Water Supply

    Leg

    2

    4

    Adjust the number 40º on the handle with mark line in the body, then install the handle

    If get the water temperature at 40ºC, release the handle. Make sure the spindle not rotated.

    640

    Mark LineHandle

    Spindle

    Bolt

    Handle

    40oC

    Safety Knob

    Open full the stop valve and check the water temperature 40ºC. When water temperature not 40ºC , set the water temperature until get 40ºC then follow step 5 and 6.

    2 X Ø8 Holes

    TX449SEV1N"EGO" Thermostat Bath & Shower Mixer w/o Hand Shower Set

    MAINTENANCEAlways wipe chrome plated area with dry soft cloth, and sometimes wipe it with cloth soaked in mild soap.

    TX449SEV2Z"EGOII " Thermostat Bath & Shower Set

    _

    MARK

    Sleeve Anchor

    17142°

    Ø8

    20

    40

    5547

    Ø50

    215.5 0-7

    PJ ½150±20

    228

    0 -7

    D1205QMFT1

    Cap

    ALIGN W

    ITH MAR

    K

    OPEN

    O-Ring

    R4

    BoltWasher

    Cap

    Washer

    ATTENTION1. Use of abrasive cleaning material such as; detergents containing hydrochloric acids, thinner, polishing powder, and nylon brush is not recommended.2. Press safety knob turn left to increase temperature over 40oC.3. Please don't open the thermostat cartridge, because it cause to unstabilize temperature in this product.4. Flow Regulator should not be remove because it could damage the system

    1. Water supply pressure : 0.05 ~ 0.75 MPa.Hot water supply temperature shall be higher by 10oC. at least, than desired temperature of mixed water. (Recommendation: Hot water supply temperature =60oC)Hot water supply pressure shall be the same or lower than cold water supply .Ensure that water supply is clean (No Sand, Dirt, Etc.).

    2.

    3.

    4.

    Flow Regulator Inside (Don’t remove)

    Rain Spray Button

    Massage Spray Button