electric vehicles and power electronics.pdf

1JSL

Electric Vehicles and Power Electronics

Jih-Sheng (Jason) LaiVirginia Polytechnic Institute and State University

Center for Power Electronics Systems668 Whittemore Hall

Blacksburg, VA 24060TEL: 540-231-4741FAX: 540-231-6390

EMAIL: [email protected]

August 16, 2001

Presentation atUniversidad Technica Federico Santa Maria

Valparaiso, Chili

JSL

Outline of Presentation Part A: Background and Introduction

What are Electric Vehicles? Why Electric Vehicles? Partnership for Next Generation Vehicles

Part B: Overview of EV/HEVs on the Market GM EV1 Ford Ranger Honda EVPlus, Insight Toyota Prius Ford P2000

Part C: Power Electronic Technologies in EV/HEV Energy Sources Traction Motors/Inverters Auxiliary Motors/Inverters Bi-directional Chargers Basic Structure of a Fuel Cell Vehicle

2JSL

Part A: Background and Introduction

What are Electric Vehicles? Why Electric Vehicles? Partnership for a New Generation of Vehicles Specification of Supercar EV/HEV Configurations

JSL

EV/HEV Definitions

An Electric Vehicle is A vehicle fueled with mains electricity. An EV usually requires a battery pack as energy storage.

A Hybrid Vehicle isA chemically fueled vehicle equipped with at least one bi-directional energy reservoir. The fueled hybrid power unit (HPU) is usually a heat engine, but may be a fuel cell. Energy storage and delivery is usually electric.

3JSL

Driving Forces for EV/HEV

!!!! Simplicity (1910)!!!! Energy Security (1970)!!!! Environmental Concerns (1990)!!!! Customer Expectations (2000)

JSL

US Customer Expectations for EV/HEVs

!!!! Range: Minimum 160 km/charge!!!! Safety: Same as ICE Vehicles!!!! Performance: Same as ICE Vehicles!!!! Cost: No more than ICE vehicles!!!! Features: No less than ICE vehicles

4JSL

Partnership for a New Generation of Vehicles

LONG-TERM GOAL Development of a SupercarGas mileage: 3X average of Concorde/Taurus/Lumina, or 80 mpg Load: Six passengers + 200 pounds of luggageRange: Similar to todays models At least 80 percent recyclable

Technology Areas Hybrid/electric vehicle drive trainsDirect-injection engines Fuel cells Lightweight materials

JSL

Specifications of Baseline Vehicle and Supercar

Baseline Supercar

Curb Weight 3200 lbs 40% lessDrag coeff. 0.32 0.20Friction: 0.005 0.008 Engine: Internal Combustion flywheel, battery, ultracapacitorFuel Efficiency: 26.6 mpg 80 mpg (3X)Recycleability: 75% 80%Range (HWY): 380 miles same or betterAccel (0-62 mi): 12 seconds same or betterLuggage: 168 ft3 same or betterLoad: 6 passengers + 200 lb same or betterLife: 100,000 miles same or better

5JSL

PNGV Time Table

JSL

Where are the Energy Goes in a Conventional Car?For Metro-Highway Driving Cycle

DrivelineEngine

100%

Aerodynamics6%

Accessories2%

Engine77% Driveline

6%

Rolling5%

Braking4%

Fuel

6JSL

Electric/Hybrid Electric Vehicle Configurations

Fueltank

Xmission

ICE

Diff.Wheels

Pure ICE Drive

ICE: Internal Combustion EngineXmission: TransmissionDiff.: Differential gear

ElectricMotor

Battery

Diff.Wheels

Pure Electric Drive

Parallel Hybrid Series Hybrid

Hybrid Drives

Fueltank

Xmission

ICE

Diff.Wheels

ElectricMotorBattery

FueltankICE

Diff.Wheels

ElectricMotor

Battery

Generator

JSL

How Does a Hybrid Electric Vehicle Work?

(a) Shaft driven by both ICE and electric motor

(b) Shaft driven by electric motor and battery is charged

7JSL

Part B: Overview of EVs on the Market

GM EV1

Ford Ecostar, Ranger

Honda EVPlus, Insight

Toyata Prius

Ford P2000

JSL

General Motor EV1

Power: 137 hpTop speed: 80 miles per hourDrag coeff.: 0.19Acceleration: 0 to 60 miles, less than 9 secondsRange: 55 to 95 miles with 26 lead-acid battery pack

75 to 130 miles with Nickel-Metal Hydride (NiMH) battery pack Charging: 220 V, 6.6 kW non-contact inductive charging, 6 hours Braking: front disk, rear drum, and regenerative

Price: $33,995 MSRPLease: $424 - $574 / mo

36-month lease $0.20/mile over 30,000 miles

http://www.gmev.com/index.htm

8JSL

GM Inductive Charge Coupler

JSL

Ford Ranger and US Post Office Electric Vehicles

Battery:Fourth generation sealed lead acid 39x8 volt modules; 312 volt systemCapacity rating @ FUDS: 23 kWh (18 kWh at 80% discharge)On-board Charger: On-board, 240 V/30 A

Performance:0-50 mph acceleration: 13 secondsRated top speed (governed) : 75 mphCustomer range @ 72F: 50 milesRange - FUDS cycle @ 72F: 58 miles without A/C or heater operation

9JSL

Ford Ranger Schematic

90 hp, 3-phase AC induction

JSL

Honda EVPlus

New Technology Features

Nickel-metal hydride batteries Permanent-magnet motor Single-speed, direct-drive transmission Regenerative braking On-board charger 110- or 220-volt Heating and air conditioning High-intensity headlightsStandard Features

EPA City: 100 miles; Highway: 84 miles (Use 80% battery capacity) Meets all federal motor vehicle safety standards Dual airbags and 3-point seat belts Anti-lock braking system (ABS) Power windows, door locks and mirrors AM/FM/CD audio system Remote keyless entry and security system Cargo area with "fold-flat" rear seats Walk-in feature for rear seat access

10

JSL

Honda Insight Hybrid Electric Vehicle

Integrated Motor Assist: 1.0-liter, 3-cylinder gasoline engine + electric motorEPA mileage ratings: 61 mpg city/70 mpg highwayDriving range: 600 - 700 miles Drag coefficient: 0.25Electric motor: 36 ft-lb, 10-kW DC-brushless motor, 2.3 wide,

sits between the engine and transmission, mounted directly to the engine's crankshaft

Battery: A 144-volt nickel metal-hydride battery packInverter: An advanced electronic Power Control Unit (PCU),

adopted from Honda EV PLUS

JSL

Drivetrain of Honda Insight

11

JSL

Toyota Prius - A Hybrid Vehicle

Engine: 1.5-liter, DOHC, 16-valve, EFI 4-cylinder with Variable Valve Timing with intelligence (VVT-i)

Maximum Engine Output: 58 hp at 4,000 rpmMaximum Speed: 100 mph (engine and motor combined)Motor Type: permanent magnet, 30 kW/40 hp at 9402,000 rpmBattery Type: sealed nickel-metal hydride with 40 modulesCombined Horsepower: 58 hp engine + 40 hp motor + 3 hp batteries = 101 hpFuel Efficiency: 66 mpg (Japanese 1015 city drive mode)Maximum Range: 850 miles (combined city/highway)Regeneration Braking: Front disc/rear drum brakes with ABS

JSL

Prius Hybrid Drivetrain

12

JSL

Power Flow in Prius

BatteriesInverterGenerator

Motor

Engine

Electrical power path

Motive power path

Engine FlowStarting from rest/low speedsFull-throttle accelerationNormal drivingDeceleration/braking

Reduction Gear

JSL

Emission Comparison of Prius and Corolla

10.314.72171570.2050.1240.8640.8080.0680.0251143Corolla

12.720.81551120.0630.0010.0620.0250.0330.0021237Prius

Sec.Km/LTECarTECarTECarTECar(kg)Vehicle

AccelFrom0-60 mi/h

FuelEco-nomy

Curb Weight

NonmethaneOrganic gases(NMOG), g/km

CarbonMononxide

g/km

Nitrogen oxideg/km

Carbon dioxide

g/km

Note: Car values are vehicle exhaust (tailpipe) emissions TE values are total emissions-Car plus upstream, including fuel

cycle emission Source: IEEE Spectrum, March 2001, Pages 47 50.

13

JSL

Ford P2000 Low Storage Requirement (LSR) Car

Features:

Low Storage Requirement (LSR) Direct Injection Aluminum Through-bolt Assembly (DIATA) engine Integrated Starter/Alternator Engine shut-down during braking and at rest Very fast engine restart Improve engine dynamics and shift fell Modified shift strategy for reduced emissions Weight and cost penalties low relative to full hybrid enables limited re-generative braking

JSL

Comparison of P2000 LSR and Hybrid Vehicles

Series Parallel P2000

Platform 5 + passenger, Al-Intensive, Sedan5 passenger, Light-weight prototype

5 passenger, Light-weight prototype

HPU 55 kW, Turbo-Alternator 55 kW, 1.2 L, CIDI 55 kW, 1.2L, CIDI

Transmission none Auto 5-speed Auto 5-speed

Traction Motor 75 kW, EV transaxle 18/30 kW motor on 4x4 transfer case8 kW starter/alternator

Battery 180 kW x 6 kWh 48 kW x 2 kWh 15 kW x 0.4 kWhWeight 1401 kg 1258 kg 1000 kgFuel Economy (v. Taurus) City:

Metal Ceramic 1.8x 2.4x 2.9x 2.5x

Highway 1.4x 1.9x 2.2x 1.9x

14

JSL

Ford P2000Hydrogen Fuel Cell Car

Chemical Energy Electrical Energy Mechanical Energy

HydrogenTank

FuelCell

TractionInverterMotor

TurboCompressor

Transxle

JSL

Daimler-Chrysler NECAR IVA Fuel Cell Electric Vehicle with Built-in Reformer

Fuel: MethanolEmission: zeroTop Speed: 90 mphRange: 280 miles

15

JSL

Part C: Power Electronic Technologies in EV/HEV

Energy Sources and Storages! Batteries! Fuel Cells

Traction Motors Soft-Switching Inverters Bi-Directional Chargers

JSL

Energy Sources and Storages

Lead Acid Batteries Nickel Metal-Hydride (NiMH) Batteries Lithium Batteries Fuel Cells

16

JSL

Lead Acid Batteries

Flood type: First design in 1880s With flat pasted plate immersed in a dilute sulfuric acid

electrolyte

Valve Regulated Lead Acid (VRLA) type: Original development in 1960s with sealed lead acid

batteries The gases produced during operation are recombined

to minimize water losses Typical gas recombination efficiency is 95% Gas recombination cell can be made with Absorptive

Glass Mat separator or Gel Electrolyte

Source: www.hawker.invensys.com

Electric Vehicles use deep charge/discharge type VRLA batteries

JSL

VRLA Battery Charging Voltage and Currentfor a Typical Tubular Gel Product

Typical State of Charge Voltage 100% 2.13 V70% 2.09 V50% 2.06 V20% 2.02 V* Measuring open ckt voltage after

battery rested >24 hr.

Charging Voltage at diff temp.0C 2.35 V10C 2.28 V20C 2.23 V30C 2.20 V35 C 21.7 V

Charging Current Typically 10% of the 10-hour capacity, C10 In general, not exceed 30% of C10 For fast charge, keep 2.35 V per cell with 10% of C10 as the current

limit

Source: www.hawker.invensys.com

17

JSL

Nickel Metal-Hydride (NiMH) Batteries

Negative Electrode: rare earth/nickel alloys LaNi5 (AB5 alloys) titanium and zirconium (AB2 alloys)

Positive Electrode: Sintered-type positive electrodes are economical and rugged while exhibiting excellent high-rate performance, long cycle life, and good capacity

Electrolyte: Alkaline, a dilute solution of potassium hydroxide

Energy Density: Improved energy density (up to 40 percent greater than Nickel Cadmium cells)

GM EV1 Test Range: 55 to 95 miles with 26 lead-acid battery pack 75 to 130 miles with Nickel-Metal Hydride (NiMH) battery pack

JSL

Comparison of Nickel-Metal Hydride to Nickel Cadmium Batteries

Nominal Voltage Same (1.25V) Discharge Capacity NiMH up to 40% greater than NiCd Discharge Profile Equivalent Discharge Cutoff Voltages Equivalent High Rate Discharge Capability Effectively the same rates High Temp (>35oC) Discharge Capability NiMH slightly better than NiCd cells Operating Temperature Limits Similar, NiMH slightly better at cold temp Self-Discharge Rate Similar to NiCd Cycle Life Similar to NiCd Mechanical Fit Equivalent Selection of Sizes/Shapes/Capacities Equivalent Environmental Issues Reduced with NiMH because of elimination

of cadmium toxicity concerns. Collection of spent NiMH batteries is not mandated

18

JSL

Lithium/Thionyl Chloride Batteries

Negative Electrode: mixture of carbon, Teflon, fiberglass, alcohol, and water

Positive Electrode: Lithium

Electrolyte: Thionyl Chloride

Lithium batteries have been widely used in computers and communications and will be competing with NiMH batteries for EV applications

JSL

Fuel Cell Vehicle - Future Trend

Fuel Cell Electric Vehicles (FCEVs) are similar to a battery-powered EV except that fuel cells replace batteries. As with batteries, fuel cell emit no carbon dioxide, although carbon dioxide and other emissions may be created in vehicle manufacturing and fuel production.

A fuel cell produces electricity by combining hydrogen and oxygen in an electrochemical reaction. Fuel cells require no combustion, unlike a conventional gasoline- or diesel-powered engine. The only emission from hydrogen fuel cells is water vapor.

19

JSL

Fuel Cell Vehicle Configurations with Different Sources

Hydrogen storage

Fuel Cell Stack

Inverter

Bi-directionaldc-dc

converter

Gear

Battery

Methanol storage

Fuel cell stack

Inverter

Bi-directionaldc-dc

converter

Gear

Battery

Fuel cell stack

Inverter

Bi-directionaldc-dc

converter

Gear

Battery

Methanol reformer

Gasoline storage

Partial oxidation

ref.

Motor

/Gen

Motor

/Gen

Motor

/Gen

(a) With hydrogen (b) With Methanol (c) With Gasoline

JSL

Basic Hydrogen-Oxygen Fuel Cell

Fuel (H2)

Oxidant

(Air O2)

Water

(H2O)

Electrical loads+-2e- 2e-

1/2 O2

H2 2H+ 2H+

Ion Exchange Membrane(IEM)

Electrode (-) Electrode (+)

H2OElectrolyte

20

JSL

Proton Exchange Membrane (PEM) Fuel Cell

CO2

Methanol Fuel

CH3CHOxidant

(Air O2)

Water

(H2O, N2, O2)

Electrical loads+-6e- 6e-

CO2+

6H+3H2O

6H++

3/2 O2

H+

H+

H+

H+

H+

H+

H+

H+

H+

H+

Proton Exchange Membrane(PEM)

Electrode (-) Electrode (+)

Water

H2O

Vaporizer

MethanolReformer

CO2Oxidization

Catalyst

JSL

Fuel Cell Output Voltage and Current Characteristic

0

50

100

150

200

250

300

350

400

0 100 200 300

Stack Current(A)

Stac

k Vo

ltage

(V)

21

JSL

Fuel Cell Output Power and Current Characteristic

0102030405060708090

0 100 200 300

Stack Current (A)

Net

Pow

er (k

W)

JSL

20 kW Future Car Stack

22

JSL

Traction Motors/Inverters

Motor Design Consideration1. Using Federal Urban Driving Schedule to Find Most

Critical Speed and Torque Region2. Optimize Motor Design in Proper Torque-Speed

Regions Motor Types Inverter Partitioning for Integrated Inverter-Motor Soft-Switching Inverter Considerations Bi-directional Chargers for Fuel Cell Vehicles

1. A 20-kW Non-isolated Bi-directional Converter2. A 5-kW Isolated Bi-directional Converter

JSL

Motor Design Consideration 1 Using Federal Urban Driving Schedule to Find Most Critical

Speed and Torque Regions

FUDS CYCLE

0

20

40

60

0 500 1000 1500

Time (sec)

Spee

d (m

ph)

Battery Current (Pos=Discharge)

-100-50

050

100150

0 500 1000 1500

Time (seconds)

Cur

rent

(am

p)

23

JSL

Torque-Speed Envelope

0

20

40

60

80

100

120

0 5 10 15 20 25Speed (x1000 rpm )

Torq

ue (l

bft,h

p) TorquePowerEfficiency

Motor Design Consideration 2 Optimize Motor Design in Proper Torque-Speed Regions Resulting High-Speed (20,000 rpm) Design that Cuts Size and Weight by 30%

JSL

Motor Types

Induction Motor Permanent Magnet Motor Switched Reluctance Motor Other Combinations

24

JSL

Inverter Partitioning for Integrated Inverter-Motor

INVERTERPOWER MODULE

COLD PLATE

INSULATOR

TRACTIONPOWER INPUT

COOLANT/LUBRICANT

INTPUT

GEAR LUBRICANT

GEAR ASSEMBLY

CONTROLLERMOUNTING BLOCK

MOTOR LINE COOLANT

OPTICALDRIVE SIGNAL

OPTICAL STATUS SIGNAL

ADVANCED AC MOTOR AND CASING

JSL

Inverter Design and Partioning

InductionMotor

SensorConditioning

ia ib va vb

r

Hall Sensors

OpticalEncoder

IGBT Modules

Interface Circuit

DSP Circuit

Battery

Fuel CellUnit

Pow

er F

low

Con

trol

Gate Driver withProtection

25

JSL

Using Optical Fiber to Link Integrated Power Stage and Control Interface

SensingBoard

DSPInterfaceBoard

GateDriver

GateDriver

GateDriver

IGBT Based Inverter Power Stage

Optical fiber link

Motor

JSL

Compact Gate Driver with Optical Fiber Link

PWM

Fault

Optical Fiber

IGBT Module

MC

3315

3 +15V

-5V

54

78

23

Ron

Roff

+15V

6 1

-5V

26

JSL

Soft-Switching Inverter Considerations

Zero-Voltage-Transition Auxiliary Resonant Commutated Pole (ARCP) Inverter for AC Motor Drives

Zero-Current Transition (ZCT) Inverter Advantages:

Allow high switching frequencies Low switching losses Low EMI

JSL

Turn-on Loss Reduction with Soft-Switching

Vce(100v/div)

Is(10A/div)

Vce(100v/div)

Is(10A/div)

Hard-switching Soft-switching

Voltage, Vswitch

Power, Pswitch

Current, Iswitch

27

JSL

Turn-off Loss Reduction with Soft-Switching

Vce(100v/div)

Is(10A/div) Is(10A/div)

Vce(100v/div)

Hard-switching Soft-switching

Current, Iswitch

Voltage, Vswitch

Power, Pswitch

JSL

A Zero-Voltage-Transition Inverter for AC MotorsAuxiliary Resonant Commutated Pole (ARCP)

Lra

Vs

C1 C3

C4 C6

C5

C2

S1 S3 S5

S4 S6 S2

Csp

Csn

acmotor

Lrb

Sb

Sa

Lrc

Scauxiliary circuits

28

JSL

Basic Operating Principle of ZVT Soft-Switching

t1 t2 t3 t4

ILr

IS1

IS2IC2

IC1Sr

Ix ILoad

0

0

0

0

C1

C2

ILoad

S2

S1

LrILr

C1

C2

ILoad

S2

S1

LrILr

From t1 to t2 From t2 to t2

t2 t3

C1

C2

ILoad

S2

S1

LrILr

C1

C2

ILoad

S2

S1

LrILr


JSL

ARCP ZVT Inverter Test Results

ia

SX1 SX2

LX1

CX1

CX2ia

S1

S2

CS

CS

Vdc

Auxiliary Circuit

D1

D2

DS1

DS2

M1

A : vg(S2) (20 V/div)B : ia (200 A/div)C : iax (200 A/div)D : vS2 (200 V/div)

A

BC

D

2 s/div

SX1 SX2

LX1

CX1

CX2

S1

S2

CS

CS

Vdc

Auxiliary Circuit

D1

D2

M1ia

91

92

93

94

95

96

97

50.2 80.9 5.0 20.7 50.5 101.4 5.9 12.2 41.6 10.1 14.8 31.9 13.3 20.4

1920 3770 5635 7560 9460

Torque [N-m]

Speed [rpm]

Inve

rter

effi

cien

cy [%

]

with diodeswithout diodes

29

JSL

Zero Current Transition Inverter

ACMotor

CsVs

Sr4 Sr6 Sr2

Sr3 Sr5Sr1 S1 S3 S5

S4 S2S6

Lr Cr

JSL

Basic Operation of ZCT Soft Turn-on

ILr

IS1

VCr

S1

ILoad

0

ILoad

S2

S1

LrILr ILoad

S2

S1

LrILr


Cr

ILoad

S2

S1

LrILr ILoad

S2

S1

LrILr


+ VCr

Cr

0

t1 t2 t3 t4

0

0

VCE1

Sr0

t0

0

currentdirectionin thisperiod

currentdirectionin thisperiod

30

JSL

Test Results of 30-kW Soft-Switching Inverters

5 /d i

Ix (200 A/div)

Iload (200A/div)

5ms/div

ARCP ZVT

ZCT Vce (250 V/div)

ILoad (200A/div)

5ms/div

Ix (200 A/div)

Vce (200 V/div)

JSL

Basic Operation of ZCT Soft Turn-off

ILr

IS1

VCr

S1

ILoad

0

ILoad

S2

S1

LrILr ILoad

S2

S1

LrILr


Cr

ILoad

S2

S1

LrILr ILoad

S2

S1

LrILr


+ VCr

Cr

0

t8 t9t6 t10

0

0

VCE1

Sr0

t5

0

Initial VCr is negative

Vdc

t7

31

JSL

Soft-Switching Inverter Assembled in EV1 Chassis

Development...

Testing...

On the Road...

JSL

Bi-directional Charger for Fuel Cell Powered Electric Vehicles

Inverter

Vol

tage

Cla

mp

CompressorMotor

Expanding Unit

CM

EUC

ontr

olle

r

OtherLoads

Bi-d

irec

tiona

l Po

wer

Flo

w

dc-d

c C

onve

rter

High Voltage Bus (>300V)+

Motor

Energy Storage Cap.

Fuel

Cel

l

Batteryfor Startup

+

32

JSL

Why Bi-directional DC-DC Converter is Needed?

1. Need to have high voltage to start up the CMEU controller.2. Need to stabilize the bus voltage during transient

conditions. 3. Need battery to charge the dc bus bus for the initial startup

power (Boost operation)3. Need to keep battery charged (Buck operation)

JSL

Circuit Topology Considerations for the Bi-directional DC-DC Converter

1. Single-directional vs. bi-directional2. Isolated vs. non-isolated3. Multiple-leg Interleaved vs. single-leg 4. Voltage source vs. current source for either primary or

secondary side5. Low side battery with 12 V, 42 V, or 180 V vs. high side

fuel cell at about 300 V

33

JSL

Non-Isolated Buck Converter L

R+

Vg

C

+

v

vgs

Q1

D1g

sd

vgs

iL

v

Gate on Gate off

DTs DTs

Inductor charged

Inductor discharged

Capacitor charged

Capacitor discharged

gDVV =

Average output voltage:

where D is the duty ratio. Because D < 1, V is always less than Vg " buck converting

JSL

Non-Isolated Boost Converter

+

CQ1

D1L

RVg

v

+

iL iD

iQ iCvL+

vgs

vgs

iL

v

Gate on Gate off

DTs DTs

Inductor charged

Inductor discharged

Capacitor discharged

Capacitor charged

gg VDV

DV

'1

11

=

=

Average output voltage:

where D is the duty ratio, and D = 1 D. Because D < 1, Vis always greater than Vg "boost converting

34

JSL

Non-Isolated Single-Directional Boost ConverterNon-Interleaved vs. Interleaved

Load

L1

L2

S1u S2u

S1d S2d

+

Vbatt

i1

i2 VFC

Load

L

Su

Sd

+

Vbatt

iVFC

(b) Interleaved(a) Non-Interleaved

JSL

A Non-Isolated Bi-Directional DC-DC Converter with Interleaved Control

Ld2

Ld3

S2u S3u

S2d S3d

VFC

Power module

Vbatt

Load

35

JSL

Ripple Current Cancellation Effect in a 20 kW Interleaved Boost Converter

33 A/div50 s/div

IL1 IL2

IL1 + IL2

33 A/div

JSL

Efficiency Test Results of a 20 kW Interleaved Boost Converter

86889092949698

0 5000 10000 15000 20000 25000

Predicted

experimental

Output Power (W)

Effic

ienc

y (%

)

DCM operated converter has parasitic ringing losses at the light load condition, and the efficiency is suffered.

At Vin = 200 V, Vo = 300 V

36

JSL

Isolated Buck Converter

Q1 Q3

Q2 Q4

Vg

L

Cfa

b

+

C Rv+

1 : n

Suitable for high voltage input and low voltage output Zero-voltage switching can be achieved with phase-shift modulation

JSL

Isolated Boost Converter

Suitable for low voltage input and high voltage output The main problem is high voltage stress on the switching devices

Q1 Q3

Q2 Q4

Vg

L

Cfa

b

+

C Rv+

1 : n

37

JSL

Low-Voltage Side Half-Bridge Current-Fed Isolated Bi-directional Converter

L1 L2

Cc

S1 S2

S5

S6S7

S8

CoVb

1:nLlk

!!!! Low switch counts!!!! Simple transformer winding structure!!!! Low transformer current Start-up problem Low choke ripple frequency (fs) Duty cycle limitation#### Passive clamp is easy to implement but lossy

Rc

JSL

Low-Voltage Side Full-Bridge Current-Fed Isolated Bi-directional Converter

!!!! Simple voltage clamp circuit implementation!!!! Simple transformer winding structure and lower turns ratio!!!! Low transformer current!!!! High choke ripple frequency (2fs) Start-up problem High switches count

L

S1

S2

S5

S7 S6

S8

CoVb

1:nLlk

S3Cc

S4

Sc

38

JSL

Complete Bi-directional dc-dc Charger with Clamping and Start-up Circuits

Lk+

_

S1

S3 S2

S4S5

S7Cc

L

Sc

A

S6

S8

B D

C-Ip

Ic

Vpn

+

_

Tr

1:n

Vo

CoCinIs

Vb

+

_

1:n LkfDf

IL

Ifp

n

Start-up circuit

Active Clamp circuit

JSL

Prototype of a Liquid Cooled Bi-directional DC-DC Converter to be Installed in a Fuel

Cell Vehicle

39

JSL

Start-up Mode Operation

IL

Is

Vo

ILref

125 A/d

20 A/d

100 A/d

100 V/d

Start-upcommandinitiation

Transitionfrom start-upto regularboost

Average current loop regulated

Loadengaged atVo=255 V

Voregulated Vb = 12 V, IL = 161 A, Vo = 280 V,

Pd = 1.83 kW in steady state

Start Up Process:

t0-t1 Start up mode, open loop controlled

t1-t2 Boost mode, open loop controlled

t2-t3 Boost mode, inner current loop regulated

t3- Boost mode, outer voltage loop regulated

t0 t1 t2 t3

JSL

Switch Voltage and Current Waveforms in Boost (Discharging) Mode Operation

S3

Is

Vpn

10 A/d

10 V/d

Vb = 8 V, IL = 228 A, Vo = 288 V, Pd = 1.55 kW

40

JSL

Comparison of Measured Efficiency Profile forDischarging (Boost) Mode Operation

400 600 800 1,000 1,200 1,400 1,6000.82

0.84

0.86

0.88

0.9

0.92

0.94

Po

Efficie ncy

Full-Bridge

L-Type

10 V

8 V

10 V

8 V

Test conditions:

Start-up, battery discharging

Battery voltage: Vb = 8 and 10 VHigh side voltage: Vo = 288 VSwitching freq.: fs = 20 kHz

1. Higher battery voltage, higher overall efficiency.2. Full bridge is more efficient than the L-type half-bridge converter in overall

operating range.3. Efficiency at light-load exceeds 90% with full-bridge version.4. L-type converter is lossy due to passive clamp circuit.

JSL

Switch Voltage and Current Waveforms in Buck (Charging) Mode Operation

Vcd

Is

Vpn

250 V/d

20 A/d

50 V/d

Vb = 15 V, IL = 335 A, Vo = 425 V, Pcp = 5 kW

41

JSL

Comparison of Measured Efficiency Profile forCharging (Buck) Mode Operation

1,000 2,000 3,000 4,000 5,0000.7

0.7250.75

0.7750.8

0.8250.85

0.8750.9

0.9250.95

Pch (W)

Efficie ncy

Full-Bridge

L-TypeTest conditions:

Regenerative Mode Battery voltage: Vb=15 V High voltage bus: Vo=425 V

1. L-type half-bridge efficiency reaches only 90% 2. Full bridge converter is more efficient with peak efficiency 95% because

more devices in parallel on low-voltage side active clamp circuit provides lossless snubbing soft-switching with zero-voltage zero-current operations

JSL

Summary and Discussions

Development of EV/HEV is very vital in recent years HEV has hit the market since 1999 Fuel cell is becoming the choice of energy source for future

EVs Power electronics is the main driver of EV/HEV Key power electronics technologies are traction motor/inverter

drives and bi-directional chargers Power electronics engineers are in great demand

electric vehicles and power electronics.pdf

Documents