electrical machines and energy conversion unit 1 deck 1 magnetism basics
TRANSCRIPT
Electrical Machines and
Energy Conversion
Unit 1 Deck 1Magnetism Basics
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Magnetic fields are described by drawing flux lines that represent the magnetic field.
Summary
Where lines are close together, the flux density is higher.
Where lines are further apart, the flux density is lower.
Magnetic Quantities
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
The unit of flux is the weber. The unit of flux density is the weber/square meter, which defines the unit tesla, (T), a very large unit.
Summary
Flux density is given by the equationwhere
B = flux density (T) = flux (Wb)
A = area (m2)
B=A
F lu x l in e s (
A rea (m )2
Magnetic Quantities
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Example: What is the flux density in a rectangular core that is 8 mm by 10 mm if the flux is 4 mWb?
Summary
B=A
3
2-3 -3
4 10 Wb50 Wb/m = 50 T
8 10 m 10 10 mB
Magnetic Quantities
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
• Magnetic flux lines surround a current carrying wire.
Summary
• The field lines are concentric circles.
Magnetic Quantities
• As in the case of bar magnets, the effects of electrical current can be visualized with iron filings around the wire – the current must be large to see this effect.
Current-carrying wire
Iron filings
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Summary
• Permeability () defines the ease with which a magnetic field can be established in a given material. It is measured in units of the weber per ampere-turn meter.
Magnetic Quantities
• Relative Permeability (r) is the ratio of the absolute permeability to the permeability of a vacuum.
• The permeability of a vacuum (0) is 4 x 10-7 weber per ampere-turn meter, which is used as a reference.
0 r
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Summary
• Reluctance (R) is the opposition to the establishment of a magnetic field in a material.
R= reluctance in A-t/Wbl = length of the path = permeability (Wb/A-t m).A = area in m2
Magnetic Quantities
A
l
R
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Fm = NI
• Recall that magnetic flux lines surround a current-carrying wire. A coil reinforces and intensifies these flux lines.
Summary
• The cause of magnetic flux is called magnetomotive force (mmf), which is related to the current and number of turns of the coil.
Fm = magnetomotive force (A-t)
N = number of turns of wire in a coil I = current (A)
Magnetic Quantities
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Summary
• Ohm’s law for magnetic circuits is
Magnetic Quantities
• flux () is analogous to current• magnetomotive force (Fm) is analogous to voltage• reluctance (R) is analogous to resistance.
What flux is in a core that is wrapped with a 300 turn coil with a current of 100 mA if the reluctance of the core is 1.5 x 107 A-t/Wb? 2.0 Wb
RmF
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Summary
• The magnetomotive force (mmf) is not a true force in the physics sense, but can be thought of as a cause of flux in a core or other material.
Current in the coil causes flux in the iron core.
What is the mmf if a 250 turn coil has 3 A of current?
750 A-t
Magnetic Quantities
Iron core
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Summary
• Magnetic field intensity is the magnetomotive force per unit length of a magnetic path.
H= Magnetic field intensity (Wb/A-t m)Fm = magnetomotive force (A-t)
l = average length of the path (m)N = number of turns I = current (A)
H =
F m
l H = NI
lor
• Magnetic field intensity represents the effort that a given current must put into establishing a certain flux density in a material.
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Summary
• This relation between B and H is valid up to saturation, when further increase in H has no affect on B.
• If a material is permeable, then a greater flux density will occur for a given magnetic field intensity. The relation between B (flux density) and H (the effort to establish the field) is
B = H
= permeability (Wb/A-t m).H= Magnetic field intensity (Wb/A-t m)
Magnetic Quantities
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Summary
• As the graph shows, the flux density depends on both the material and the magnetic field intensity.
M a g n e tic F ie ld In te n s ity, , (A t/m )H
Flux
den
sity
, ,
(Wb/
/m)
B2
S a tu ra tio n b e g in s
M a g n e tic m a te r ia l
N o n -m a g n e t ic m a te r ia l
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
SummaryAs H is varied, the magnetic hysteresis curve is developed.
(d )(c )
B
H
(b )
B
H
(a )
B
H
(f )
B
H
(g )
B
H
(e )
0 H sa t
Sa tura tio n
0
B sa t B R
H = 0 H
H sa t
B sa t
Sa tura tio n B
H C
0
H0 0
H = 0
B R
B
H sa t
B sa t
H C
H
B
H C
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Summary
A B-H curve is referred to as a magnetization curve for the case where the material is initially unmagnetized. The B-H curve differs for different materials; magnetic materials have in common much larger flux density for a given magnetic field intensity, such as the annealed iron shown here.
Magnetization Curve
M agn etic F ield In tensity, H , (A -t/m )200 400 600 800 1000 1200 16001400 1800 2000
0
0 .5
1 .0
1 .5
2 .0
0
Flu
x D
ensi
ty, B
, (T
)
M agn etic F ield In tensity, H , (A -t/m )200 400 600 800 1000 1200 16001400 1800 2000
0
0 .5
1 .0
1 .5
2 .0
0
Flu
x D
ensi
ty, B
, (T
)
Annealed iron
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Relative motion
When a wire is moved across a magnetic field, there is a relative motion between the wire and the magnetic field.
When a magnetic field is moved past a stationary wire, there is also relative motion.
NS
NS
In either case, the relative motion results in an induced voltage in the wire.
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
The induced voltage due to the relative motion between the conductor and the magnetic field when the motion is perpendicular to the field is dependent on three factors:
Summary
Induced voltage
• the flux density
• the length of the conductor in the magnetic field
• the relative velocity (motion is perpendicular)
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Faraday experimented with generating current by relative motion between a magnet and a coil of wire. The amount of voltage induced across a coil is determined by two factors:
Summary
Faraday’s law
1. The rate of change of the magnetic flux with respect to the coil.
NS
V- +Voltage is indicated only when magnet is moving.
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Faraday also experimented generating current by relative motion between a magnet and a coil of wire. The amount of voltage induced across a coil is determined by two factors:
Summary
1. The rate of change of the magnetic flux with respect to the coil.
2. The number of turns of wire in the coil.
NS
V- +
Faraday’s law
Voltage is indicated only when magnet is moving.
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Just as a moving magnetic field induces a voltage, current in a coil causes a magnetic field. The coil acts as an electromagnet, with a north and south pole as in the case of a permanent magnet.
Summary
Magnetic field around a coil
No rthSo uth
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Summary
A dc generator includes a rotating coil,
DC GeneratorMechanical drive turns the shaft
which is driven by an external mechanical force (the coil is shown as a loop in this simplified view). As the coil rotates in a magnetic field, a pulsating voltage is generated.
Brushes
Commutator
To external circuit
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Magnetic flux densityFlux
Magnetizing force
Magnetomotive force
Permeability
Tesla
Weber
Weber/ampere-turn-meter
Ampere-turn/Weber
Ampere-turn
Ampere-turn/meter
B
RFm
H
Reluctance
It is useful to review the key magnetic units from this chapter:
Quantity SI Unit Symbol
Magnetic units
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Magnetic field
Magnetic flux
Weber (Wb)
Permeability
Reluctance
The lines of force between the north pole and south pole of a permanent magnet or an electromagnet.The SI unit of magnetic flux, which represents 108 lines.
A force field radiating from the north pole to the south pole of a magnet.
Selected Key Terms
The measure of ease with which a magnetic field can be established in a material.
The opposition to the establishment of a magnetic field in a material.
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Magnetomotive force (mmf)
Solenoid
Hysteresis
Retentivity
An electromagnetically controlled device in which the mechanical movement of a shaft or plunger is activated by a magnetizing current.
A characteristic of a magnetic material whereby a change in magnetism lags the application of the magnetic field intensity.
The cause of a magnetic field, measured in ampere-turns.
Selected Key Terms
The ability of a material, once magnetized, to maintain a magnetized state without the presence of a magnetizing current.
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Induced voltage (vind)
Faraday’s law
Lenz’s law
A law stating that the voltage induced across a coil of wire equals the number of turns in the coil times the rate of change of the magnetic flux.
Voltage produced as a result of a changing magnetic field.
Selected Key Terms
A law stating that when the current through a coil changes, the polarity of the induced voltage created by the changing magnetic field is such that it always opposes the change in the current that caused it. The current cannot change instantaneously.
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Quiz
1. A unit of flux density that is the same as a Wb/m2 is the
a. ampere-turn
b. ampere-turn/weber
c. ampere-turn/meter
d. tesla
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Quiz
2. If one magnetic circuit has a larger flux than a second magnetic circuit, then the first circuit has
a. a higher flux density
b. the same flux density
c. a lower flux density
d. answer depends on the particular circuit.
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Quiz
3. The cause of magnetic flux is
a. magnetomotive force
b. induced voltage
c. induced current
d. hysteresis
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Quiz
4. The measurement unit for permeability is
a. weber/ampere-turn
b. ampere-turn/weber
c. weber/ampere-turn-meter
d. dimensionless
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Quiz
5. The measurement unit for relative permeability is
a. weber/ampere-turn
b. ampere-turn/weber
c. weber/ampere-turn meter
d. dimensionless
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Quiz
6. The property of a magnetic material to behave as if it had a memory is called
a. remembrance
b. hysteresis
c. reluctance
d. permittivity
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Quiz
7. Ohm’s law for a magnetic circuit is
a.
b.
c.
d.
Fm = NI
B = H
A
l
R
RmF
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Quiz
8. The control voltage for a relay is applied to the
a. normally-open contacts
b. normally-closed contacts
c. coil
d. armature
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Quiz
9. A partial hysteresis curve is shown. At the point indicated, magnetic flux
a. is zero
b. exists with no magnetizing force
c. is maximum
d. is proportional to the current
B
H
BR
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Quiz
10. When the current through a coil changes, the induced voltage across the coil will
a. oppose the change in the current that caused it
b. add to the change in the current that caused it
c. be zero
d. be equal to the source voltage
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Quiz
Answers:
1. d
2. d
3. a
4. c
5. d
6. b
7. c
8. c
9. b
10. a
Unit 10Unit 10
Electronics FundamentalsCircuits, Devices and Applications - Floyd © Copyright 2009 Pearson
Electrical Machines
and Energy Conversion
Unit 1 Deck 1Magnetism Basics
Electrical Machines and Energy Conversion
End of Presentation