embedded systems
DESCRIPTION
EMBEDDED SYSTEMS & ITS APPLICATIONSTRANSCRIPT
EMBEDDED SYSTEMS????
BY. RUCHI SHARMABVCOE
NEW DELHI
• In order to avoid or reduce road accidents this module can be placed in automobile vehicles.
• Sensors acts as a Neuron for the detection of an obstacle.• The NN is the multilayer feed-forward network
with back propagation training algorithm. • Uses Tangent-sigmoid function.
What is • An Embedded system is an applied computer system.• “Embedded system", it constantly evolves with advances in technology
and dramatic decreases in the cost of implementing various hardware and software components.
• Embedded systems have become very important today as they control many of the common devices we use.
• An embedded system is some combination of computer hardware and software, either fixed in capability or programmable, that is specifically designed for a particular kind of application device.
APPLICATIONS OF EMBEDDED SYSTEM:
• We are surrounded with many embedded products and your daily life largely depends on the proper functioning of these gadgets.
• Apart from all these, many controllers embedded in a car it take care of car operations between the bumpers and most of the times you tend to ignore all these controllers.
• Consumer applications: Office automation:
Industrial automation:
Today a lot of industries are using embedded systems for process control. Computer networking:
Embedded systems are used as bridges routers etc..
Telecommunications
MICRO CONTROLLER
MICRO CONTROLLER
REGULATED POWER SUPPLY
REGULATED POWER SUPPLY
LCD
IR SENSOR1
IR SENSOR2
IR SENSOR3
IR SENSOR4
IR SENSOR5
IR SENSOR6
DRIVER IC
DRIVER IC
DC MOTOR
DC MOTOR
Block diagram
Main Elements in this project
Rps
• Here we can use Ac as well as Dc • For Ac we use a circuit in order convert it to DC
through
We Basically use a SMF (sealed maintenance free) battery, it's a type of lead acid battery, which are rechargeable with specifications
12v,1.3AH and 0.58 kgs
Micro controller• The microcontroller used in this project is Atmel AT89S52
AT89S52:•8K Bytes of In-System Programmable (ISP) Flash Memory•4.0V to 5.5V Operating Range•256 x 8-bit Internal RAM•32 Programmable I/O Lines •Three 16-bit Timer/Counters•Low-power Idle and Power-down Modes •Fast Programming Time •Flexible ISP Programming (Byte and Page Mode) •Green (Pb/Halide-free) Packaging Option•Auto Erase before writing and Auto Verify after writing
IR sensors
• An electronic device that emits and/or detects infrared radiation in order to sense some aspect of its surroundings
• Infrared sensors can measure the heat of an object, as well as detect motion.
An infrared emitter is an LED made from gallium arsenide, which emits near-infrared energy at about 880nm.
IR transmitter
IR Transmitter Diode
Infra red transmitter emits IR rays in planar wave front manner
It propagates along straight line in forward direction.
IR rays have the characteristics of producing secondary wavelets when it collides with any obstacles in its path.
This property of IR is used here.
IR receiverInfrared photo receiver is a two terminal PN junction device, which operates in a reverse bias.
Working of Infrared communication
• The transmitter section consists of a 555 timer IC functioning in astable mode. The output from astable mode is fed to an IR LED via resistor which limits its operating current.
• Infrared LED in the transmitter section emits IR radiation which is focused by a plastic lens (optics) into a narrow beam.
• The device works best when well shielded from abient light, and when the distance between the sensor and the reflective surface is small(less than 5mm).
LCD DISPLAY• A liquid crystal display (LCD) is a thin, flat electronic visual
display that uses the light modulating properties of liquid crystals.
• •Display construction……16 Characters * 2 Lines• •Display type………Positive Transflective• •Operating temperature………Indoor• •Driving voltage………………Single power• •Type……………………COB (Chip On Board)• •Number of data line……8-bit parallel• •Connector……………Pin
DC MOTOR
Based on simple electromagnetism
DRIVER ICL293D Dual H-Bridge Motor Driver
Here with one IC we can interface two DC motors which can be controlled in both clock wise and anti clock wise directions
L293D has an output current of 600mA and peak output current of 1.2A per channel.
The output supply has a wide range from 4.5 V to 36V, which has made L293D as the best choice for DC motor Driver.
Some other Hardware components Used:
Wheels: Two Free wheels are used at back side they are High quality Plastic Tracked Wheel for motors with 6 mm diameter.And one free moving wheel is placed in the front of the body ( Mettalic Cache Body)
Buzzer
A buzzer or beeper is an audio signaling device, which may be mechanical,
electromechanical, or Piezoelectric.
AND Gate IC(DM74LS2IN) Preset
Here we used an open style preset to set the frequency or the sensitivity of light .
Project Kit
ADVANTAGES AND DISADVANTAGES
• Obstacle can be easily notified with IR sensors so that we can avoid accidents
• These are the cheapest sensors when compared to the remaining sensors
•Most infrared sensors must be lined up or they will not work.•It needs a direct line of sight between the transmitter and receiver. For example, it doesn't work through walls or doors.
• In future By using Ultrasonic sensors works on a principle similar to radar or sonar, Ultrasonic sensors generate high frequency sound waves and evaluate the echo which is received back by the sensor. So we can overcome the disadvantages seen here .
• By constructing this module inside a car we can have a safe journey under driver guidance, and most of the vehicle accidents can be avoided