emc vspex with emc xtremsf and emc xtremsw cache · pdf fileemc vspex with emc xtremsf and emc...

DESIGN GUIDE

EMC VSPEX WITH EMC XTREMSF AND EMC XTREMCACHE

EMC VSPEX

Abstract

This Design Guide describes how to use EMC® XtremSF™ and EMC XtremCache™ in a virtualized environment with an EMC VSPEX™ Proven Infrastructure for VMware vSphere or Microsoft Hyper-V. This Design Guide also illustrates how to configure XtremSF, allocate XtremCache resources following best practices for maximum effectiveness, and use all the benefits that XtremCache offers.

December 2013

2 EMC VSPEX with EMC XtremSF and EMC XtremCache Design Guide

Copyright © 2013 EMC Corporation. All rights reserved. Published in the USA.

Published December 2013.

EMC believes the information in this publication is accurate as of its publication date. The information is subject to change without notice.

The information in this publication is provided as is. EMC Corporation makes no representations or warranties of any kind with respect to the information in this publication, and specifically disclaims implied warranties of merchantability or fitness for a particular purpose. Use, copying, and distribution of any EMC software described in this publication requires an applicable software license.

EMC2, EMC, and the EMC logo are registered trademarks or trademarks of EMC Corporation in the United States and other countries. All other trademarks used herein are the property of their respective owners.

For the most up-to-date listing of EMC product names, see EMC Corporation Trademarks on EMC.com.

EMC VSPEX with EMC XtremSF and EMC XtremCache Design Guide

Part Number H12565

http://www.emc.com/legal/emc-corporation-trademarks.htm

http://www.emc.com/legal/emc-corporation-trademarks.htm

Contents


Contents

Chapter 1 Introduction 9

Purpose ............................................................................................................... 10

Business value ..................................................................................................... 10

Scope .................................................................................................................. 10

Audience.............................................................................................................. 11

Terminology ......................................................................................................... 11

Chapter 2 Before You Start 13

Deployment workflow overview ............................................................................. 14

Essential reading .................................................................................................. 14

VSPEX Solution Overviews ................................................................................ 14

VSPEX Implementation Guides.......................................................................... 14

VSPEX Proven Infrastructures ............................................................................ 15

Chapter 3 Solution Overview 17

Introduction ......................................................................................................... 18

EMC VSPEX Proven Infrastructure........................................................................... 18

EMC XtremCache: The business case ..................................................................... 19

XtremSF and XtremCache ...................................................................................... 20

XtremSF ........................................................................................................... 20

XtremCache ..................................................................................................... 20

Business benefits of XtremSF and XtremCache ....................................................... 21

XtremSF ........................................................................................................... 21

XtremCache ..................................................................................................... 21

XtremCache features............................................................................................. 22

XtremCache management ................................................................................. 28

VNX integration ................................................................................................ 30

Oracle RAC support .......................................................................................... 30

Software-only feature ....................................................................................... 31

AIX support ...................................................................................................... 31

Solution architecture ............................................................................................ 32

How XtremCache works .................................................................................... 32

XtremCache in a virtualized environment ........................................................... 35

Contents


Chapter 4 Solution Design Considerations and Best Practices 39

Overview .............................................................................................................. 40

XtremCache Performance Predictor ........................................................................ 40

Requirements .................................................................................................. 40

Sample output from XtremCache Performance Predictor ..................................... 41

VSPEX environments that can benefit from XtremCache .......................................... 44

Selecting an XtremSF card ..................................................................................... 46

Design best practices ....................................................................................... 46

MLC versus SLC ................................................................................................ 46

Virtualization design considerations ...................................................................... 47

Sizing recommendations .................................................................................. 47

Performance recommendations ........................................................................ 48

XtremCache placement considerations .................................................................. 48

Flexibility ......................................................................................................... 48

Design best practices ....................................................................................... 48

VMware considerations......................................................................................... 50

Hyper-V considerations ......................................................................................... 52

Chapter 5 XtremCache Solution for Applications 54

Overview .............................................................................................................. 55

Architecture of XtremCache deployment on VMware ............................................... 55

Architecture of XtremCache deployment on Hyper-V ............................................... 57

XtremCache for SQL Server OLTP database ............................................................. 58

Benefits of XtremCache in a SQL Server OLTP environment ................................. 58

Best practices .................................................................................................. 59

Use case design and deployment ...................................................................... 59

Configuration of XtremCache in the VMware environment................................... 61

Test results ...................................................................................................... 61

XtremCache for Exchange Server ........................................................................... 63

Benefits of XtremCache in an Exchange environment ......................................... 63

Best practices .................................................................................................. 64



Test results ...................................................................................................... 70

XtremCache for SharePoint.................................................................................... 74

Benefits of XtremCache in a SharePoint environment ......................................... 74

Best practices .................................................................................................. 74



Contents


Test results ...................................................................................................... 77

XtremCache for Oracle OLTP database ................................................................... 79

Benefits of XtremCache in an Oracle environment .............................................. 79

Best practices .................................................................................................. 79


Test results ...................................................................................................... 81

XtremCache for private cloud ................................................................................ 82

Benefits of XtremCache in a private cloud environment ...................................... 83

Best practices .................................................................................................. 83



Test results ...................................................................................................... 86

Chapter 6 References 90

EMC documentation ............................................................................................. 91

Other documentation ............................................................................................ 92

Links .................................................................................................................... 92

Appendix A Ordering Information 94

Ordering XtremSF and XtremCache ........................................................................ 95

Contents


Figures Figure 1. VSPEX Proven Infrastructure .............................................................. 18

Figure 2. I/O gap between the processor and storage subsystems .................... 19

Figure 3. VMware live migration ...................................................................... 23

Figure 4. XtremCache data deduplication ........................................................ 24

Figure 5. XtremCache data deduplication architecture overview ........................ 25

Figure 6. Split-card mode used for SQL Server configuration ............................. 27

Figure 7. XtremCache Management Center....................................................... 29

Figure 8. XtremCache deployment in an Oracle RAC environment ...................... 31

Figure 9. Read Hit example with XtremCache ................................................... 32

Figure 10. Read Miss example with XtremCache................................................. 33

Figure 11. Write example with XtremCache ........................................................ 34

Figure 12. XtremCache implementation in a VMware environment ...................... 35

Figure 13. XtremCache in a VMware environment ............................................... 36

Figure 14. XtremCache in a Hyper-V environment ............................................... 37

Figure 15. XtremCache Performance Predictor sample output: collecting performance data ............................................................................. 41

Figure 16. XtremCache Performance Predictor sample output: I/O size distribution ..................................................................................... 42

Figure 17. XtremCache Performance Predictor sample output: predicting the cache hit rate ............................................................................. 43

Figure 18. XtremCache Performance Predictor sample output: disk latency prediction ........................................................................................ 44

Figure 19. XtremCache use cases ...................................................................... 45

Figure 20. Comparison between SLC and MLC flash cell data storage .................. 46

Figure 21. Cache device configuration screen .................................................... 50

Figure 22. XtremCache configuration using EMC VSI plug-in ............................... 51

Figure 23. XtremCache implementation in VMware environment for VSPEX .......... 51

Figure 24. XtremCache implementation in Hyper-V environment for VSPEX .......... 53

Figure 25. Architecture of the VSPEX Proven Infrastructure for XtremCache deployment on VMware .................................................................... 56

Figure 26. Architecture of the VSPEX Proven Infrastructure for XtremCache deployment on Hyper-V .................................................................... 57

Figure 27. Architecture design for XtremCache enabled SQL Server virtual environment..................................................................................... 60

Figure 28. SQL Server AlwaysOn XtremCache deployment .................................. 61

Figure 29. Performance boost after enabling XtremCache ................................... 62

Figure 30. Architecture design for XtremCache-enabled Exchange virtual environment..................................................................................... 66

Figure 31. XtremCache deployment for Exchange 2010 on vSphere .................... 67

Figure 32. Enabling data deduplication on the XtremCache device ...................... 68

Contents


Figure 33. Exchange 2010 performance with XtremCache and LoadGen workload 71

Figure 34. XtremCache statistics with data deduplication ................................... 71

Figure 35. Exchange server CPU utilization with XtremCache data deduplication . 73

Figure 36. Exchange server disk latencies with XtremCache data deduplication ... 73

Figure 37. Exchange database LUN performance with XtremCache data deduplication ................................................................................... 74

Figure 38. Architecture design for XtremCache enabled SharePoint environment . 76

Figure 39. XtremCache deployment for SharePoint 2010 on vSphere .................. 77

Figure 40. Content database latency dropped after enabling XtremCache ........... 78

Figure 41. Full crawl performance improved after enabling XtremCache .............. 78

Figure 42. Architecture design for XtremCache enabled Oracle 11g R2 environment..................................................................................... 80

Figure 43. XtremCache deployment for Oracle 11g R2 on vSphere ....................... 81

Figure 44. OLTP TPM improvement .................................................................... 82

Figure 45. Architecture design for XtremCache-enabled private cloud environment with multiple applications ................................................................ 85

Figure 46. Deduplication statistics for SQL Server OLTP ...................................... 87

Tables Table 1. Terminology ..................................................................................... 11

Table 2. Deployment process: XtremSF and XtremCache overlay on VSPEX Proven Infrastructure .............................................................. 14

Table 3. Performance characteristics of selected XtremSF cards ....................... 20

Table 4. XtremSF device card group for cache pool in ESXi environment ........... 26

Table 5. XtremCache management utilities ..................................................... 28

Table 6. XtremCache management utilities ..................................................... 29

Table 7. SLC and MLC flash comparison ......................................................... 47

Table 8. Recommended cache for each application ......................................... 48

Table 9. Performance data with OLTP load ...................................................... 63

Table 10. XtremCache deployment in a private cloud environment..................... 86

Table 11. Performance summary for the private cloud environment.................... 88

Contents


Chapter 1: Introduction


Chapter 1 Introduction

This chapter presents the following topics:

Purpose ............................................................................................................... 10

Business value ..................................................................................................... 10

Scope .................................................................................................................. 10

Audience .............................................................................................................. 11

Terminology ......................................................................................................... 11



Purpose

EMC® VSPEX™ Proven Infrastructures are optimized for virtualizing business-critical applications. VSPEX provides partners with the ability to plan and design the virtual assets to support applications such as Microsoft SQL Server, Microsoft SharePoint, Microsoft Exchange, and Oracle Database on a VSPEX private cloud.

The EMC VSPEX with EMC XtremSF™ and EMC XtremCache™ solution provides partners with a server-based caching solution that reduces application latency and increases throughput. This solution runs on a VMware vSphere or Microsoft Hyper-V virtualization layer, backed by the highly available EMC VNX® family of storage systems. The computing and network components, while vendor-definable, are designed to be redundant and are sufficiently powerful to handle the processing and data needs of the virtual machine environment.

This design guide describes how to select and configure XtremCache resources for a VSPEX Proven Infrastructure and includes best practices and the results of use case testing.

Business value

IT administrators are often challenged to improve the performance of applications running heavy input/output (I/O) loads, while continuing to minimize the cost of the supporting systems. These I/O sensitive applications are typically limited by storage latency and response times. XtremCache is intelligent caching software that uses server-based flash technology to improve performance by reducing latency and accelerating throughput for dramatic application performance improvement.

XtremCache accelerates read performance by putting the data closer to the application. It also protects data by using a write-through cache to the networked storage array to deliver persistent high availability (HA), integrity, and disaster recovery. XtremCache, coupled with array-based EMC FAST™ software, creates the most efficient and intelligent I/O path from the application to the datastore. The result is a networked infrastructure that is dynamically optimized for performance, intelligence, and protection for both physical and virtual environments.

Scope

This design guide is an overlay solution that describes how to select and deploy XtremCache resources on a VSPEX Proven Infrastructure for VMware vSphere or Microsoft Hyper-V. Furthermore, this guide illustrates best practices and recommendations for using XtremCache to improve the performance of virtualized applications running on a VSPEX Proven Infrastructure.



Audience

This guide is intended for qualified EMC VSPEX partners. The guide assumes that VSPEX partners who intend to deploy XtremSF and XtremCache on respective applications are:

Qualified to sell and implement the application(s) that will be used in conjunction with the XtremCache solution

Qualified by EMC to sell, install, and configure the EMC VNX family of storage systems

Certified for selling VSPEX Proven Infrastructures

Qualified to sell, install, and configure the network and server products required for VSPEX Proven Infrastructures

Trained in and familiar with EMC’s XtremSF hardware and XtremCache software

Readers must also have the necessary technical training and background to install and configure:

EMC VSPEX private cloud solutions for VMware vSphere or Microsoft Hyper-V, depending on the hypervisor in use

Windows Server 2012 with Hyper-V or VMware vSphere as the virtualization platforms

External references are provided where applicable and EMC recommends that readers become familiar with these documents. For details, see Essential reading.

Terminology

Table 1 includes the terminology used in this guide.

Table 1. Terminology

Term Definition

Cache page size The smallest unit of allocation that is inside the cache, typically a few kilobytes in size. The default XtremCache page size is 8 KB.

CSV Cluster-shared volume. A Windows Server clustering feature that enables multiple clustered virtual machines to use the same logical unit number (LUN).

DAS Direct-attached storage

DSS Decision support system

IOPS Input/output operations per second

MLC Multi-level cell flash. A flash memory technology using multiple levels per cell to allow more bits to be stored using the same number of transistors.

NFS Network File System



Term Definition

PCIe Peripheral Component Interconnect Express

SLC Single-level cell flash. A type of solid-state storage (SSD) that stores one bit of information per cell of flash media.

tempdb Refers to a system database used by Microsoft SQL Server as a temporary working area during processing.

VHDX Hyper-V virtual hard disk format

VMDK VMware virtual machine disk format

Working set The frequently accessed data that is likely to be promoted to XtremCache

XtremCache EMC server flash-caching software

XtremSF EMC Peripheral Component Interconnect Express (PCIe) Flash cards with industry-leading performance

Chapter 2: Before You Start


Chapter 2 Before You Start


Deployment workflow overview............................................................................. 14

Essential reading ................................................................................................. 14



Deployment workflow overview

EMC recommends that you refer to the process flow in Table 2 to design and implement your XtremSF and XtremCache overlay on the VSPEX Proven Infrastructure.

Table 2. Deployment process: XtremSF and XtremCache overlay on VSPEX Proven Infrastructure

Step Action Reference

1 Review the Xtrem products and features. EMC documentation

2 Determine if the XtremCache solution is appropriate for your application.

Solution Design Considerations and Best Practices

3 Select and order the right VSPEX Proven Infrastructure.

VSPEX Proven Infrastructures

4 Select the required XtremCache hardware and determine where to place the cards.

XtremCache Solution for Applications

5 Deploy and test your virtualized applications. VSPEX Implementation Guides

Essential reading

EMC recommends that you read the following documents, available from the VSPEX space in the EMC Community Network or from the VSPEX Enablement Center.

Refer to the following VSPEX Solution Overview documents:

EMC VSPEX Server Virtualization for Midmarket Businesses

EMC VSPEX Server Virtualization for Small and Medium Businesses

Refer to the following VSPEX Implementation Guides:

EMC VSPEX for Virtualized Microsoft Exchange 2010 with Microsoft Hyper-V

EMC VSPEX for Virtualized Microsoft Exchange 2010 with VMware vSphere

EMC VSPEX for Virtualized Microsoft Exchange 2013 with Microsoft Hyper-V

EMC VSPEX for Virtualized Microsoft Exchange 2013 with VMware vSphere

EMC VSPEX for Virtualized Microsoft SharePoint 2010 with Microsoft Hyper-V

EMC VSPEX for Virtualized Microsoft SharePoint 2010 with VMware vSphere

EMC VSPEX for Virtualized Microsoft SharePoint 2013 with Microsoft Hyper-V

EMC VSPEX for Virtualized Microsoft SharePoint 2013 with VMware vSphere

EMC VSPEX for Virtualized Microsoft SQL Server 2012 with Microsoft Hyper-V

EMC VSPEX for Virtualized Microsoft SQL Server 2012 with VMware vSphere

VSPEX Solution Overviews

VSPEX Implementation Guides

https://community.emc.com/community/partner/vspex?view=overview

https://education.emc.com/VSPEX_Enablement_Center/



EMC VSPEX for Virtualized Oracle Database 11g OLTP

Refer to the following VSPEX Proven Infrastructures:

EMC VSPEX Private Cloud VMware vSphere 5.1 for up to 100 Virtual Machines

EMC VSPEX Private Cloud VMware vSphere 5.1 for up to 500 Virtual Machines

EMC VSPEX Private Cloud VMware vSphere 5.1 for up to 1,000 Virtual Machines

EMC VSPEX Private Cloud VMware vSphere 5.5 for up to 1,000 Virtual Machines

EMC VSPEX Private Cloud Microsoft Windows Server 2012 with Hyper-V for up to 100 Virtual Machines

EMC VSPEX Private Cloud Microsoft Windows Server 2012 with Hyper-V for up to 500 Virtual Machines

EMC VSPEX Private Cloud Microsoft Windows Server 2012 with Hyper-V for up to 1,000 Virtual Machines

VSPEX Proven Infrastructures

Chapter 3: Solution Overview


Chapter 3 Solution Overview


Introduction ......................................................................................................... 18

EMC VSPEX Proven Infrastructure .......................................................................... 18

EMC XtremCache: The business case..................................................................... 19

XtremSF and XtremCache...................................................................................... 20

Business benefits of XtremSF and XtremCache ...................................................... 21

XtremCache features ............................................................................................ 22

Solution architecture ............................................................................................ 32



Introduction

This design guide describes the requirements and process for deploying EMC XtremSF and XtremCache on VSPEX Proven Infrastructures. The guidance applies to all VSPEX Proven Infrastructures unless specifically stated otherwise.

This chapter provides an overview of VSPEX Proven Infrastructure, XtremSF and XtremCache, and the key technologies used in the XtremSF and XtremCache overlay for the VSPEX Proven Infrastructure. A VSPEX Proven Infrastructure includes servers, storage, network components, and application components that focus on small and medium business private cloud environments. The XtremSF and XtremCache overlay provides latency reduction and accelerates throughput for dramatic application performance improvement.

EMC VSPEX Proven Infrastructure

A VSPEX Proven Infrastructure, as shown in Figure 1, is a modular, virtualized infrastructure validated by EMC and delivered by EMC partners. VSPEX includes components supporting virtualization, servers, network, storage, and backup designed by EMC to deliver reliable and predictable performance. VSPEX enables businesses to transform their IT, application and end user computing environments by providing complete virtualization solutions that have been sized and tested by EMC.

Figure 1. VSPEX Proven Infrastructure

VSPEX provides the flexibility to choose network, server, and virtualization technologies that fit a customer’s environment to create a complete virtualization solution. VSPEX delivers faster deployment for EMC partner customers, with greater simplicity and efficiency, more choice, and lower risk to a customer’s business.



EMC XtremCache: The business case

The capabilities of modern processors continue to widen the performance gap between CPUs and disks. Often, the disk datastore becomes a bottleneck in any deployed solution.

As processing capacity and workloads increase, the storage system is challenged to keep pace with growing I/O demands. The performance of the magnetic disk remains relatively flat while CPU performance improves 100-fold every decade, as shown in Figure 2. XtremSF Flash drives can help to close the gap.

Figure 2. I/O gap between the processor and storage subsystems

Flash technology can be used in different ways in the storage environment to compensate for the performance limitations of disk based storage. EMC’s architectural approach is to use the right technology in the right place at the right time. This includes using flash in the following ways:

In the storage array

As an array-side cache

As a server-side cache

As a tier

As the storage for the entire application



XtremSF and XtremCache

XtremCache (formerly known as VFCache or EMC XtremSW Cache) is the first step in EMC’s long-term server flash strategy. This strategy delivers a server-side storage product featuring a combination of intelligent caching software—XtremCache—and server-based Peripheral Component Interconnect Express (PCIe) Flash hardware—XtremSF.

XtremCache software turns the XtremSF card into a caching device, to enhance the performance of a wide variety of critical transactional and decision support applications. XtremCache can run with a wide variety of multilevel cell (MLC) and single-level cell (SLC) XtremSF Flash cards.

VSPEX partners can order XtremCache software and XtremSF hardware through Channel Express. For ordering information, refer to Appendix A: Ordering Information.

XtremSF is single, low-profile server flash hardware card that fits in any rack-mounted server within the power envelope of a single PCIe slot, and is available with a broad set of MLC and SLC capacities. It can be deployed:

As local storage that sits within the server to deliver high performance

In combination with XtremCache software to improve network storage array performance, while maintaining the level of protection required by critical application environments

You can use EMC XtremCache software to create server-side cache for data. XtremCache is designed with the following basic principles:

Performance: Reduce latency and increase throughput to dramatically improve application performance.

Intelligence: Add another tier of intelligence by extending FAST array-based technology into the server.

Protection: Deliver performance with protection by using the high availability and disaster recovery features of EMC networked storage.

Table 3 shows the performance characteristics of some selected XtremSF cards.

Table 3. Performance characteristics of selected XtremSF cards

350 GB MLC

550 GB MLC

700 GB MLC

1.4 TB MLC

2.2 TB MLC

350 GB SLC

700 GB SLC

Read Bandwidth (MB/s)

3,175 1,555 3,215 3,215 2,600 3,215 3,215

Write Bandwidth (MB/s)

330 512 570 605 1,000 756 1900

Random 4 K Read IOPS

730 K 175 K 750 K 750 K 340 K 715 K 750 K

XtremSF

XtremCache



350 GB MLC

550 GB MLC

700 GB MLC

1.4 TB MLC

2.2 TB MLC

350 GB SLC

700 GB SLC

Random 4 K Write IOPS

23 K 50 K 50 K 95 K 110 K 95 K 205 K

Random 4 K Mixed IOPS

105 K 110 K 190 K 200 K 220 K 415 K 415 K

Read Access Latency (4 kB) μs

100 76 100 100 76 50 50

Write Access Latency (4 kB) μs

13 30 13 13 30 13 13

Business benefits of XtremSF and XtremCache

XtremSF delivers extremely high performance with low latency and enables applications to achieve memory-class based performance. It eliminates the need for additional memory or storage capacity purchases, and thereby helps reduce overall deployment footprint. The XtremSF family of server-based PCIe Flash cards offers customers the following benefits:

Leading performance: XtremSF Flash devices are proven to deliver a record 1.13 million IOPS in a standard form factor—an achievement unmatched in the industry. The XtremSF device’s next-generation design delivers twice the throughput of other offerings in the market to enhance real world workloads in Web-scale and other applications.

Unmatched flexibility: The XtremSF Flash device is available in a broad range of eMLC (from 350 GB up to 2.2 TB) and SLC (350 GB and 700 GB) capacities. In addition, when deployed with XtremCache, XtremSF devices can be used as caching devices for accelerated performance with array protection for applications such as Oracle, Microsoft SQL Server, and Microsoft Exchange.

New levels of efficiency: XtremSF Flash devices deliver the industry’s lowest total cost of ownership (TCO)—up to 58 percent better TCO than other offerings. All XtremSF products are standard half-height, half-length, 25W PCIe cards, providing the highest storage capacity with the smallest footprint for maximum performance, best density, and lowest power consumption, reducing CPU utilization by up to 50 percent.

XtremCache delivers the following major benefits:

Provides performance acceleration for read-intensive workloads

As a write-through cache, enables accelerated performance with the protection of the back-end, networked storage array

Provides an intelligent path for the I/O and ensures that the right data is in the right place at the right time

XtremSF

XtremCache



In split-card mode, enables you to use part of the server flash for cache and the other part as DAS for temporary data

By offloading flash and wear-level management onto the PCIe card, uses minimal CPU and memory resources from the server

Achieves greater economic value when data deduplication is enabled by providing an effective cache size larger than the physical size, and longer card life expectancy

Works in both physical and virtual environments

Integrated with EMC Virtual Storage Integrator (VSI) plug-ins for vSphere makes it simple to manage and monitor XtremCache in a VMware environment

Works in active/passive clustering environments

Works with VMware live migration

Provides a highly scalable performance model in the storage environment

XtremCache features

XtremCache software caches the most frequently referenced data on the server-based PCIe card XtremSF, thereby putting the data closer to the application.

The XtremCache caching optimization automatically adapts to changing workloads by determining the most frequently referenced data and promoting it to the server flash cache. This means that the “hottest” (most active) data automatically resides on the PCIe card in the server for faster access.

XtremCache accelerates reads and protects data by using a write-through cache to the storage array to deliver persistent high availability, integrity, and disaster recovery.

XtremCache is transparent to applications, so no rewriting, retesting, or recertification is required to deploy XtremCache in the environment.

XtremCache works with any storage array in the enviornment. Regardless of the vendor or type of the storage, it works seamlessly to improve the performance of the storage array.

XtremCache offloads much of the read traffic from the storage array, which allows it to allocate greater processing power to other applications. While one application is accelerated with XtremCache, the array’s performance for other applications is maintained or even slightly enhanced.

XtremCache enhances both virtualized and physical environments. Integration with VSI plug-ins for vSphere makes it simple to manage and monitor XtremCache.

Server-side flash caching for maximum speed

Write-through caching for total protection

Application and storage agnostic

XtremCache vSphere integration



VMware automated live migration

XtremCache supports live virtual machine migration (vMotion), HA, DRS, and SRM. You can continue to use these technologies exactly as they are used without the presence of XtremCache.

During the migration process, the virtual machine is operational and the cache is purged with a temporary I/O performance impact.

XtremCache software must be installed on the virtual machines and the ESX host. The XtremCache device is created as a RDM device in the XtremCache pool, and passes through to the assigned virtual machine. The cache device appears to the source and target ESX hosts as shared resources with a multipath plug-in (MPP) over RDM.

On each virtual machine, a virtual SCSI device is created with a fixed ID. This ID is the same on all ESX hosts within the cluster. The virtual machine accesses the flash device using an RDM disk over that SCSI device. Write activity to the cache flows through the RDM disk to the MPP on the ESX server and from there it flows straight to the flash device.

Figure 3 illustrates the live migration with XtremCache.

Figure 3. VMware live migration

Post migration

After the migration, the cache, which always starts cold, must “warm up” again because the virtual machine now uses a new physical device. This warm-up process also prevents data on the source device from becoming out of sync with the cached data. The migrated virtual machine can then follow the HA/DRS policies without any problems regardless of the XtremCache availability on the new ESXi server.

XtremCache works seamlessly with the Windows Hyper-V host and the virtual machines that are deployed from it.

Integration with Hyper-V



XtremCache does not require a significant amount of memory or CPU cycles because all flash and wear-level management is done on the PCIe card and—unlike other PCIe solutions—does not use server resources.

XtremCache creates the most efficient and intelligent I/O path from the application to the datastore, which results in an infrastructure that is dynamically optimized for performance, intelligence, and protection for both physical and virtual environments.

Currently, EMC is the only vendor to provide customers with a deduplication option on a server cache flash card. Deduplication can provide the following benefits:

Better cost per gigabyte: Using an effective cache size that is larger than the physical cache size

Longer card life expectancy: Reduction in the number of write operations to the flash card resulting in lower wear out

Data deduplication can eliminate redundant data by storing only a single copy of identical chunks of data, while enabling this data to be referenced. As shown in Figure 4, when deduplication is enabled, only one copy of data is actually stored in XtremCache. With some additional memory space for pointers, the amount of data that can be cached increases dramatically.

Figure 4. XtremCache data deduplication

Data deduplication uses server memory to process the deduplication function and maximize the capacity of XtremCache. You can enable or disable this function as needed. Figure 5 shows the deduplication architecture in XtremCache.

Minimum impact on system resources

Data deduplication



Figure 5. XtremCache data deduplication architecture overview

XtremCache supports several common types of active/passive native operating system clustering.

Supported active/passive clustering

Some environments (RHEL Cluster Suite, Veritas Cluster Server, and AIX PowerHA) require configuring the supplied XtremCache Clustering script to ensure that stale data is never retrieved. The scripts use Cluster Management events that relate to an application service start/stop transition to trigger a mechanism that purges the cache. Other environments, such as Microsoft Cluster Service and Oracle Real Application Clusters, do not require script configuration.

Note: When you use XtremCache in a cluster, do note define quorum disks as source devices.

Microsoft active/passive cluster support

For XtremCache version 2.0 and higher, multiple applications in a cluster can use XtremCache for Microsoft Cluster Server environments. The required scripts are automatically installed during XtremCache installation. Cluster resources are automatically defined when you define a source device.

Microsoft Cluster Service requires the following:

Windows PowerShell must be installed on the cluster nodes. PowerShell is usually installed by default during a typical Windows installation.

Active/passive clustering support



The XtremCache driver must be installed on all nodes in the cluster, including nodes without any server devices.

Applications and shared disks with dependencies must be defined before you add or start the XtremCache source device. Resources will appear automatically in the Microsoft Cluster Services (MSCS) window after sources are defined.

In Microsoft active/passive clusters, when the passive node of one cluster is also configured as the active node of another database cluster, XtremCache supports that configuration by specifying different XtremCache devices for the two different clusters on two different nodes.

You can install Multiple XtremSF cards on a single server and configure them as cache devices to improve application performance.

XtremCache pool in an ESXi server

In VMware environments, each ESXi server can have one or more XtremCache pools. You can add devices from a specific vendor and model to the same cache pool.

You can use a flash card in ESXi environments for DAS or for caching, but not for both (split-card). When you add cards to the local cache pool, all cards from the same group are added according to those defined in Table 4:

Table 4. XtremSF device card group for cache pool in ESXi environment

XtremSF device name Member of group

XtremSF550 Group A

XtremSF2200

XtremSF300S Group B

XtremSF700

Group C XtremSF1400

XtremSF350S

XtremSF700S

Using flash cards for DAS

If you use a flash card for DAS, any card used from the same group will be used as the DAS-intended card and will not be used for caching. For example:

For an ESX host on which XtremSF550 and XtremSF2200 are installed, if both cards are from the same group, both cards must be used for caching or both cards must be used for DAS.

For an ESX host on which XtremSF550 and XtremSF700 are installed, if the cards are from different groups, the cards can be used in any combination of caching and DAS with no limitations.

Multiple cards per server



XtremCache includes a unique software option that enables you to split the XtremSF card between the cache and the local storage. You can simultaneously use the card as a caching device for critical data, both as a read and as a write storage device for temporary data. You can fully optimize your workload by adjusting caching or storage without having to change your card deployment.

With this feature, both read and write operations from the application to the local storage are performed directly on the flash capacity in the server. Since the data on the local flash storage does not persist in any storage array, it is best used for ephemeral data only, such as the operating system swap space and temporary file space.

Figure 6 shows an example of a use case for the split-card mode of XtremCache. In a SQL Server, where the tempdb needs acceleration for both read and write operations but the database file only needs read acceleration, XtremSF can be configured so that part of the card can be used for the local storage as tempdb, and part of it can be used as a cache. However, there is a limitation in this configuration as vMotion is not viable when the tempdb storage is local.

Figure 6. Split-card mode used for SQL Server configuration

Split-card mode support



XtremCache includes management utilities described in Table 5.

Table 5. XtremCache management utilities

Management utility Description

Command Line Interface (CLI) You can use the CLI to execute vfcmt commands to configure and manage XtremCache. It is installed with the XtremCache installation.

VSI Plug-in The EMC VSI Storage Viewer for VMware vSphere™ (VSI) is a plug-in to VMware’s vSphere Client that provides a single management interface used for managing EMC storage including XtremCache within the vSphere environment.

Lite Client Xtrem Lite Client enables you to view, manage, and monitor the XtremCache of a physical or virtual machine or ESX host. You can also use Lite Client to manage the XtremCache of an individual system.

Communication between the Lite Client and managed systems uses the CIM/XML protocol over HTTPS on the port 5989.

Management Center The XtremCache Management Center provides all the functionality of the Lite Client. In addition, it retains machine history and enables you to manage multiple machines (physical, virtual, and ESX hosts) from a single view.

VNX users can benefit from the integration of the management center with Unisphere remote for VNX. For VNX LUNs being accelerated by XtremCache, this integration simplifies the cache performance monitoring by displaying the information directly on the Unisphere Remote management screens. In addition, you can see the health information of XtremSF flash cards that are managed by the Management Center from Unisphere Remote.

To enable this integration, register the XtremCache Management Center in the Unisphere Remote by providing the IP addresses and credentials of the Management Center.

XtremCache management



Figure 7 shows the XtremCache Management Center’s performance view.

Figure 7. XtremCache Management Center

Table 6 shows the differences between the XtremCache management utilities that you can choose to fit the specific needs of your environment.

Table 6. XtremCache management utilities

CLI VSI plug-in Lite Client Management Center

Environment All VMware Physical , except AIX

All, except AIX

Installation Installed by default with caching software runs on the server

VMware plug-in for vSphere Client

Desktop client installed and runs on a windows machine

Run as a virtual appliance (vApp), Web interface, no client installation

Scale Manages single machine

Manages multiple machines

Manages single machine

Manages multiple machines

Recommended for Scripting, when GUI access isn’t needed, or for AIX

Management of multiple accelerated virtual machines

GUI access to a single machine, with minimal setup costs

Managing multiple machines, or when history and audit on changes is important

External API - - - REST API



If VNX Unisphere Remote is deployed, XtremCache can be managed and monitored directly through Unisphere Remote.

Configuration and monitoring, such as link and launch capabilities to drill down and configure any cache device in the system, can all be done in a single management panel with:

LUN selection based on VNX trending analysis

Performance and health monitoring

Discovery and configuration

XtremCache support for Oracle RAC enables active/active shared storage in an Oracle environment with a distributed cache coherency algorithm. XtremCache supports Oracle RAC in the following environment:

Oracle 11g on Windows, RHEL, or OEL (running the same OS versions that are supported by XtremCache)

Running Oracle Clusterware 11g with Ethernet interconnect

Up to eight nodes per cluster

At installation time, XtremCache automatically recognizes the presence of Oracle RAC and switches operation to clustering mode.

When a certain block of information is overwritten in shared storage and on a cache device, other cache devices in the cluster will delete that block from their cache devices to prevent the use of invalid data.

When a node joins the cluster, XtremCache must know about it to provide modification to shared storage by that node. The integration with the Oracle cluster management using SCSI-3 Persistent Reservations to notify the back-end storage to wait until XtremCache “approves” the joining node before accessing the storage.

When a node leaves the cluster, all cache devices will change to pass-through mode and are purged to ensure coherency.

We recommend using this feature to cache your data file LUNs. Do not use it to cache redo logs, archives, temporary data, or grid data.

Note: XtremCache is supported in AIX environments, but we do not support XtremCache for Oracle RAC in AIX environments.

VNX integration

Oracle RAC support



Figure 8 shows how an Oracle RAC environment deploys XtremCache.

Figure 8. XtremCache deployment in an Oracle RAC environment

XtremCache’s software-only feature enables you to use XtremCache to serve as a cache device with any other devices. For example, you can use it in blade servers as well as many other device forms including all SATA or SAS SSD devices and PCIe cards such as HHHL and HHFl. You can also use devices with SATA, ATA, or SCSi bus configurations. VMware environments support SCSi devices only.

XtremCache versions 2.0 and above support IBM Power 7 servers with AIX 6.1 and 7.1. The standard edition of PowerVM; Native clustering (PowerHA active/passive); and Certified AIX SSDs are supported as underlying hardware.

Software-only feature

AIX support



Solution architecture

If the application I/O is for a source volume on which XtremCache has not been enabled, then the XtremCache driver is transparent to the application I/O and works as if there is no XtremCache driver in the server I/O stack. In the following examples, the application I/O is assumed for a source volume which is being accelerated by XtremCache.

Read Hit example

In this example, XtremCache has been running for some time and the application working set has already been promoted into XtremCache. The application issues a read request, and the data is present in XtremCache. This process is called “Read Hit”, as shown in Figure 9.

Figure 9. Read Hit example with XtremCache

The sequence of the steps in Figure 9 is:

1. The application issues a read request that is intercepted by the XtremCache driver.

2. Because the application working set has already been promoted into XtremCache, the XtremCache driver determines that the data being requested by the application already exists in the XtremCache. Therefore, the read request is sent to the PCIe XtremSF card rather than to the back-end storage.

3. Data is read from the XtremCache and returned to the application.

How XtremCache works



Read Hit provides the entire throughput and latency benefits of XtremCache to the application because the read request is fulfilled within the server rather than incurring latencies by going over the network to the back-end storage.

Read Miss example

In this example, the application issues a read request and the data is not present in XtremCache. This process is called “Read Miss”, as shown in Figure 10. The data is not present in XtremCache either because the card has just been installed in the server or the application working set has changed so that the application has not yet referenced this data.

Figure 10. Read Miss example with XtremCache

The sequence of the steps in Figure 10 is: 1. The application issues a read request that is intercepted by the XtremCache

driver.

2. The XtremCache driver determines that the requested data is not in XtremCache and forwards the request to the back-end storage.

3. The data is read from the back-end storage and returned to the application.

4. Once the application read request is completed, XtremCache driver writes the requested data to the XtremSF card. This process is called “promotion”. This means that when the application reads the same data again, it will be a Read Hit for XtremCache, as described in the previous example.

If all the cache pages in XtremCache are already used, XtremCache uses a least-recently-used (LRU) algorithm to write new data. If needed, the data that is least likely to be used in future is discarded first to create space for the new XtremCache promotions.



Write example

In this example, the application has issued a write request, as shown in Figure 11.

Figure 11. Write example with XtremCache

The sequence of the steps in Figure 11 is:

1. The application issues a write request that is intercepted by the XtremCache driver.

2. Since this is a write request, the XtremCache driver passes this request to the back-end storage for completion. The data in the write request is written to the XtremCache card in parallel.

If the application is writing to a storage area that has already been promoted to XtremCache, the copy of that data in XtremCache is overwritten. Therefore, the application does not receive a stale or old version of data from the XtremCache in response to future read requests. XtremCache algorithms ensure that, if the application writes some data and then reads the same data later on, the read requests will find the requested data in XtremCache.

3. Once the write operation is completed on the back-end storage, an acknowledgment for the write request is sent back to the application.

The process of promoting new data into XtremCache, as described in the previous two examples, is called “cache warm-up”. Any cache needs to be warmed up with the application working set before the application starts seeing the performance benefits. When the working set of the application changes, the cache automatically warms up with the new data over a period of time.



The implementation of XtremCache in a virtualized environment is slightly different from an implementation in a physical environment. In a virtualized environment, multiple virtual machines on the same server may share the performance advantages of a single XtremSF card or multiple XtremSF cards in the XtremCache pool.

VMware environment

Figure 12 shows an XtremCache implementation in a VMware virtualized environment.

Figure 12. XtremCache implementation in a VMware environment

An XtremCache implementation in a VMware environment consists of the following components:

A physical XtremSF card on the VMware ESX Server

XtremSF firmware and driver and XtremCache software on the ESX Server

XtremCache software in each virtual machine that needs to be accelerated using XtremCache. This includes the XtremCache driver, command line interface (CLI) package, and XtremCache Agent. Only virtual machines that need to be accelerated with XtremCache must have XtremCache software installed.

The Xtrem VSI Plug-in for XtremCache management in the VMware vCenter client

Both the raw device mapping (RDM) and Virtual Machine File System (VMFS) volumes are supported with XtremCache. Network File System (NFS) file systems in VMware environments are supported as well.

XtremCache in a virtualized environment



Figure 13 shows implementation details of a VMware environment.

Figure 13. XtremCache in a VMware environment

The flash device appears to the source and target ESXi hosts as a shared resource through a multipath plug-in (MPP) over RDM. On each virtual machine, a virtual SCSI device with a fixed ID that is identical over all ESX hosts on the cluster is used to access the flash device.

XtremCache provides the flexibility to implement its caching capacity for one or many virtual machines in the ESX host from the vCenter server, with the VSI plug-in or XtremCache Management Center providing a single view for configuration and management. To configure this environment:

The Xtrem shared datastore (named XtremSW_Cache_DS) must be created on a LUN that is visible to all ESXi hosts in the datacenter that may host a virtual machine with XtremCache on it. The LUN does not need to be larger than 1 GB.

Add the XtremSF devices to the ESXi server XtremCache pool. Multiple cards from the same group (see Table 4) on the same ESXi server will need to be added to the same cache pool.

Enable XtremCache remote monitoring from VSI plug-in.

Enable UUID mapping to support vMotion, HA, DRS, and SRM to create a cache device from the XtremCache pool. You can determine the size of the cache device by the caching requirements of the specific virtual machine.

After creating the cache device, you can use it the way as you use it in the physical environment.

Attach a source device to be accelerated. Acceleration starts by default.



The cache space in the ESX cache pool is only consumed when the virtual machine is active and there is enough space on that ESX server. vMotion activity will be successful even if there is no cache or there is not enough space on the ESX server. The cache space for XtremCache is allocated on a first-come, first-served basis.

If there is no space when the virtual machine is active, the XtremCache operates in pass-through mode (as if there is no XtremCache) until there is space for it. This allows vMotion to move the virtual machines to another ESX server even if there is not enough cache space (or if the cache card has failed for any reason).

Hyper-V environment

Figure 14 shows an implementation in a Hyper-V virtualized environment.

Figure 14. XtremCache in a Hyper-V environment

An XtremCache implementation in a Hyper-V environment consists of the following components:

A physical XtremSF card on the Windows Hyper-V server

XtremSF driver and firmware on the Windows Hyper-V server

XtremCache software on the Windows Hyper-V server

In a Hyper-V environment, all the devices that need to be accelerated are configured at the Hyper-V root server level. The installation procedure is identical to the procedure for the physical Windows server.

Unlike the VMware implementation, all virtual machines in the Hyper-V environment share the same physical XtremSF card installed on the Hyper-V server. Caching is provided through the Hyper-V host.



In the Hyper-V environment, XtremCache provides the caching capacity to support one or many virtual machines in the Hyper-V host:

Virtual disks can be defined either before or after configuring the LUN as a source device.

All virtual disks allocated on a source device LUN will be accelerated.

NFS, Hyper-V virtual hard disk (VHDX), and physical pass-through disk types are all supported. Currently, cluster- shared volumes (CSV) are not supported.

Chapter 4: Solution Design Considerations and Best Practices


Chapter 4 Solution Design Considerations and Best Practices


Overview .............................................................................................................. 40

XtremCache Performance Predictor ....................................................................... 40

VSPEX environments that can benefit from XtremCache ......................................... 44

Selecting an XtremSF card .................................................................................... 46

Virtualization design considerations ..................................................................... 47

XtremCache placement considerations ................................................................. 48

VMware considerations ........................................................................................ 50

Hyper-V considerations ........................................................................................ 52



Overview

This chapter provides best practices and considerations for the XtremCache implementation within the VSPEX Proven Infrastructure for various applications. We1 considered the following aspects during the solution design:

XtremCache Performance Predictor

XtremCache remote management console

XtremSF card selection

XtremCache layout design

Virtualization design

XtremCache Performance Predictor

XtremCache Performance Predictor is a free tool available on EMC Online Support. You can use this tool to estimate the benefits of implementing XtremCache in a specific environment. This tool collects data on the host side using common trace collection tools, and trace analysis on a host or on any laptop that meets the system requirements. The tool simulates XtremCache’s operations and generates a PDF output file describing the benefits.

This tool requires no card or software purchase and runs on all XtremCache-supported operating systems.

The tool creates a set of charts and graphics that show whether the environment can benefit from XtremCache, and provides an estimate of possible performance improvement based on:

Observed host response time

Capacity used by the host

Skew level

1 In this guide, “we” refers to the EMC Solutions engineering team that validated the solution.

Requirements

https://support.emc.com/



This section provides sample output from the XtremCache Performance Predictor tool. Figure 15 shows the performance collection and the cache configuration from a sample PDF output of the tool.

Figure 15. XtremCache Performance Predictor sample output: collecting performance data

Sample output from XtremCache Performance Predictor



Figure 16 shows the tool’s output regarding the disk I/O distribution. You can use this information to set the page size and maximum I/O size of the actual XtremCache for better performance if required (the default for page size is 8 K and maximum I/O size is 64 k).

Figure 16. XtremCache Performance Predictor sample output: I/O size distribution



Figure 17 shows the cache read analysis. If the tool indicates a very high cache hit rate, then the device under load is a good candidate for XtremCache acceleration.

Figure 17. XtremCache Performance Predictor sample output: predicting the cache hit rate



Figure 18 shows an estimate of the performance improvement gained by the disk from the XtremCache acceleration. This is a simulated result and serves a good reference for how well the application will benefit from XtremCache acceleration.

Figure 18. XtremCache Performance Predictor sample output: disk latency prediction

For best performance, use XtremCache Performance Predictor as a planning tool when including XtremCache in a VSPEX environment.

VSPEX environments that can benefit from XtremCache

Workload environments with these characteristics can generally benefit from XtremCache:

A high read-to-write workload ratio. The maximum effectiveness is gained where the same data blocks are read many times and seldom written.

A small working set that receives the maximum possible boost.

Predominantly random workloads. Sequential workloads tend to have a significantly larger, active dataset in proportion to the available XtremCache size (such as data warehousing), and so do not benefit greatly from XtremCache.

A high degree of I/O concurrency (that is, multiple I/O threads).

Smaller I/O sizes (8 KB or lower). Applications that generate a large amount of I/O, such as Exchange Server 2010, can still benefit.



The XtremCache software enables you to tune features such as page size and maximum I/O sizes, which greatly helps in these environments to continue to accelerate particular I/O activity and avoid other I/O activity (such as backup read I/O).

As explained in Chapter 3: Solution Overview, XtremCache can accelerate read operations, while all write operations are written to the storage array and are not affected by XtremCache. In many cases, improvement in write-throughput performance can be observed as XtremCache offloads the read operations, enabling the array to handle more write operations as a side benefit. XtremCache may not be suitable for more write-intensive or sequential applications such as data warehousing, streaming, media, or Big Data applications. Figure 19 shows these use cases.

Figure 19. XtremCache use cases

The horizontal axis represents a typical read-to-write ratio for an application workload. The left side represents write-heavy applications such as backups. The right side represents read-heavy applications such as reporting tools.

The vertical axis represents the working set of the application’s workload. The lower end represents applications that have a very large working set and the top of the chart represents applications with a small working set, where the majority of the I/O goes to a very small set of data. Typically, applications with a small working set occupy less space in XtremCache.

The greatest performance improvement can be achieved with XtremCache in high-read applications with a highly concentrated, small working set of data.



To summarize, you can use XtremSF as the local storage for read and write acceleration, temporary data, and large working sets, while XtremSF with XtremCache can be used for read acceleration of mission-critical data with small working sets that require data protection.

Selecting an XtremSF card

In general, the two major technologies used in all flash drives are:

SLC NAND-based flash cell

Multilevel cell (MLC) NAND-based flash cell

This section discusses which card to select when designing an XtremCache solution. EMC XtremSF has both SLC and MLC cards in different sizes to fit the different needs of a customer environment. For more information about XtremSF card sizes, see Table 3 on page 20.

Flash storage devices store information in a collection of flash cells made from floating gate transistors. SLC devices store only one bit of information in each flash cell (binary). MLC devices store more than one bit per flash cell by choosing between multiple levels of electrical charge to apply to the floating gates in the transistors, as shown in Figure 20.

Figure 20. Comparison between SLC and MLC flash cell data storage

Because each cell in MLC flash has more information bits, an MLC flash-based storage device offers increased storage density compared to an SLC flash-based version. However, MLC NAND has lower performance and endurance because of its inherent architectural tradeoffs. Higher functionality further complicates the use of MLC NAND, which makes it necessary to implement more advanced flash management algorithms and controllers.

Table 7 compares the SLC and MLC flash characteristics with some typical values.

Design best practices

MLC versus SLC



Table 7. SLC and MLC flash comparison

Features MLC SLC

Bits per cell 2 1

Endurance (erase/write cycles) About 10,000 About 100,000

Read service time (Avg.) 129 μs 38 μs

Write service time (Avg.) 1,375 μs 377 μs

Block erase (Avg.) 4,500 μs 1,400 μs

Although SLC NAND Flash offers a lower density, it also provides an enhanced level of performance in the form of faster reads and writes. Because SLC NAND Flash stores only one bit per cell, the need for error correction is reduced. SLC also allows for higher write and erase cycle endurance, making it a better fit for use in applications that require increased endurance and viability in multiyear product life cycles.

SLC and MLC NAND offer capabilities that serve two different types of applications—those requiring high performance at an attractive cost per bit (MLC), and those that are less cost sensitive and seeking even higher performance over time (SLC).

Virtualization design considerations

XtremCache is fully supported when deployed in a virtual environment with VMware vSphere ESXi technology or Windows Server Hyper-V technology. The following describes the best practices and design considerations for XtremCache in virtualized environments:

Identify the virtual machines on the ESXi server that would be a good candidate for XtremCache to accelerate its performance with reasonable cost.

Calculate the total capacity needed for XtremCache.

If needed, adjust the placement of the virtual machines in the environment to best utilize XtremCache.

Select the appropriate XtremSF card for both capacity and performance.

Sizing recommendations are available for each different application type. The implementation also varies for each different environment. Table 8 shows the minimum configurations recommended for each application, based on our testing in a controlled environment with a typical database workload and application workload. Use the numbers provided as a guideline.

To determine the sizing that best fits a specific application and environment, it is important to consider both the performance level you need and the cost you can afford. In most cases, adding more XtremCache gives better performance until the size of the cache is equal to or greater than the working set.

Table 8 provides XtremCache recommendations for each application. The cache-to-storage ratio (the cache and database storage size ratio, a 1:10 ratio, represents

Sizing recommendations



a 1 GB XtremCache for each 10 GB of data) largely depends on the active working set of the database, and will change based on actual usage.

Table 8. Recommended cache for each application

Application Database type Read-to-write ratio

Recommended XtremCache-to-storage ratio2

SQL Server/ Oracle OLTP 90:10 1:10

SQL Server/ Oracle OLTP 70:30 1:5

SharePoint Server Content/crawl 100% read 1:5

Exchange Server Mailbox 60:40 1:100

For Oracle or SQL Server online analytical processing (OLAP) applications, such as a data warehouse environment, eMLC XtremSF (alone, or in split-card mode) can be used as the tempdb to improve the query performance. Consider at least 200 GB tempdb space for every 1 TB of database.

XtremCache placement considerations

EMC XtremCache can accelerate performance on demand for applications in a VSPEX Proven Infrastructure.

The flexibility of an XtremCache implementation enables you to place XtremSF on the server that hosts the specific virtual machines requiring performance acceleration. In those virtual machines, you enable only the specific storage LUNs that need XtremCache. To ensure that those virtual machines continue to have access to XtremCache acceleration, set the appropriate affinity rules for the hypervisor so the virtual machines can reside only on those servers that are accelerated with XtremSF Cache.

Additionally, you can install XtremSF Flash cards in all physical servers in the server infrastructure, and then install and enable XtremCache across all servers.

Working from the base configuration of VSPEX, for each application you intend to run within the environment, determine which applications need XtremCache acceleration by using XtremCache Performance Predictor. This will estimate the benefits of adding the XtremCache to the environment.

2 XtremCache-to-storage ratio is the cache and database storage size ratio. If the ratio is 1:10, then for each 10 GB of data, provide at least 1 GB of XtremCache.

Performance recommendations

Flexibility

Design best practices



Use XtremCache for read acceleration of mission-critical data with small working sets that require data protection. Consider the following guidelines when placing the flash card within the server infrastructure:

Use XtremCache Performance Predictor to estimate the benefits for adding the XtremCache to the environment

Use XtremCache for read acceleration of mission-critical data with small working sets that require data protection.

Put at least two XtremSF cards within your VSPEX server infrastructure when redundancy is required.

If vMotion is required, calculate the XtremSF capacity and placement so that the remaining server and XtremSF capacity can still serve the configured XtremCache settings of all virtual machines when vMotion takes place.

For example, you configure 10 virtual machines to use 100 GB of XtremCache, which requires a total of 1 TB of XtremCache capacity. If vMotion is required, the remaining servers in the virtualized cluster with XtremCache must facilitate at least 1 TB of cache space.

If applications only need a small part of the XtremSF card capacity for each virtual machine, the virtual machines with these applications cab share the same physical card. You can place them on the same ESXi or Hyper-V host.

If a certain application demands all the available capacity of the XtremSF card, then the host should dedicate that specific card to the virtual machine. You can install Multiple XtremSF cards on the same server, if required. You can also configure multiple XtremSF cards on the same hypervisor or Cache Pool to create larger cache capacity for virtual machine(s).

The XtremCache page size is the smallest unit of allocation inside the cache. The default page size is 8 KB. The XtremCache maximum I/O size is the maximum I/O size that will be promoted into the cache. The default maximum I/O size is 64 KB.

Determine the I/O size distribution of all applications selected for acceleration. If an application generates significantly large I/O sizes (such as Exchange Server), this may warrant a change of the default page size and maximum I/O size configurations for XtremCache.

Figure 21 shows the configuration screen in VSI plugin used to change these configuration settings. The minimum size for the XtremCache device is 20 GB for any virtual machine that needs flash cache acceleration.



Figure 21. Cache device configuration screen

There is minimal resource consumption (overhead) for virtual machines using XtremCache to accelerate application performance, except when the deduplication feature is enabled. Resource consumption, including CPU and memory, depends on the application and especially depends on the size of the working set. Deduplication introduces very limited memory utilization and CPU consumption when enabled in an environment with a small working set and high skew. This is detailed in the Exchange solution example; for more information, see XtremCache for Exchange Server.

XtremCache can be disabled or enabled any time once the XtremSF card is installed on the physical host and configured for the virtual machine.

VMware considerations

This section provides the most common and important design considerations for implementing XtremCache in a VSPEX with VMware environment.

The VMware environment in a VSPEX Proven Infrastructure should follow the general VSPEX design principles and best practices for specific applications on VMware, as detailed in the VSPEX Implementation Guides.

XtremSF should be installed on each ESXi server with virtual machines that require XtremCache acceleration, as determined by customer’s performance and cost analysis.



After installing the XtremSF Flash card, you can configure the XtremCache pool within the ESXi cluster using the VSI plug-in or using XtremCache Management Center, as shown in Figure 22.

Figure 22. XtremCache configuration using EMC VSI plug-in

You can use multiple XtremCache devices in a single cache pool to support larger cache capacity in certain virtual machines. A single XtremSF cache device can also support multiple virtual machines’ cache needs, as shown in Figure 23.

Figure 23. XtremCache implementation in VMware environment for VSPEX



The size of the XtremCache should follow the best practices for each different application, as previously described in the Sizing recommendations section. For multiple applications or database LUNs, simply add the required XtremCache device size, and create a single XtremCache device for the virtual machine, as shown in Figure 23. The only exception to this is when there is a need to segregate the I/O traffic, or when one XtremSF card is not big enough for the virtual machine, and then multiple cache devices are needed.

Since each virtual machine in the VMware environment has its own XtremCache cache device, there is no contention among different virtual machines for XtremCache caching. Each deployment should be a careful balance of performance and cost considerations.

As previously noted, virtual machines are expected to migrate across the VMware cluster. Ensure that sufficient XtremCache capacity is available on other nodes to accept an “incoming” virtual machine configured for acceleration. For example, if you want to move SQLVM1 (configured with a 50 GB cache) from the host ESXServer1 to the host ESXServer2 (through a vMotion migration), ensure that ESXServer2 has at least 50 GB of free XtremCache capacity available.

Hyper-V considerations

This section provides the most common and important design considerations for implementing XtremCache in a Hyper-V environment.

The Hyper-V environment in a VSPEX implementation should follow the general VSPEX design best practices for the specific application in the Hyper-V environment, as detailed in the VSPEX Implementation Guides.

As shown in Figure 24, install XtremSF on each Hyper-V server with virtual machines that require XtremCache acceleration, as determined by the customer’s performance and cost analysis.

Once the XtremSF card is installed, configure it as the XtremCache target device on the Hyper-V server. From the Hyper-V server, configure all the LUNs requiring XtremCache acceleration as source LUNs for the XtremCache target device.

As shown in Figure 24, all VHDXs for the different virtual machines, as well as the physical pass-through disks on those LUNs configured as XtremCache source LUNs, are accelerated by XtremCache.



Figure 24. XtremCache implementation in Hyper-V environment for VSPEX

Since XtremCache in a Hyper-V environment works at the Hyper-V level, all the source devices from the different virtual machines are accelerated with the same XtremCache target. This means:

Applications may enjoy a higher level of service from XtremCache when other virtual machines on the same Hyper-V server are not as active. This is because the source device is not limited to the calculated capacity of the XtremCache and can potentially use all the available cache capacity.

There may be contention between different virtual machines if the workload and active data set (the hot data) on one of the virtual machines is overwhelmingly high and using more than its quota. To avoid contention, it is better to put applications that place a high demand on XtremCache on different Hyper-V servers, or to configure them with a different XtremSF card on the same Hyper-V server.

Currently, CSV volumes are not supported with XtremCache 1.5x software. CSV volumes will be supported in future releases.

Note: Volumes in a Hyper-V cluster do not need to be CSV to avail of the benefits of Live Migration or other advanced Hyper-V features. Also, in cases where Tier-1 applications require acceleration, it may be best not to enable CSV on those volumes and ensure they are dedicated to the application from the volume to LUN to storage array disks.

When using VHDX, all VHDXs on the same LUN that are configured with XtremCache are accelerated with XtremCache. When designing the storage layout, consider placing only the VHDXs that require XtremCache acceleration on the LUNs that are configured with XtremCache.

Chapter 5: XtremCache Solution for Applications


Chapter 5 XtremCache Solution for Applications


Overview .............................................................................................................. 55

Architecture of XtremCache deployment on VMware .............................................. 55

Architecture of XtremCache deployment on Hyper-V .............................................. 57

XtremCache for SQL Server OLTP database ............................................................ 58

XtremCache for Exchange Server........................................................................... 63

XtremCache for SharePoint ................................................................................... 74

XtremCache for Oracle OLTP database .................................................................. 79

XtremCache for private cloud ................................................................................ 82



Overview

Any VSPEX Proven Infrastructure that needs to boost the performance of applications such as Oracle and SQL Server OLTP applications, web applications, financial trading applications, and Exchange can benefit from XtremCache. XtremCache can be considered as an upgrade or add-on feature for a larger cloud solution.

This section describes application use cases where XtremCache provides value. It includes the best practices, the deployment scenarios, and the expected benefits for the following application use cases:

SQL Server

Exchange

SharePoint

Oracle

Private cloud

Architecture of XtremCache deployment on VMware

Figure 25 shows the validated architecture for an XtremCache deployment on a VSPEX Private Cloud with VMware. The XtremSF card is installed on the physical VMware ESXi server and put into an XtremCache pool. The XtremCache device created in that cache pool is assigned to the virtual machines hosting the application that needs to be accelerated. The cache device can use part or all of the available storage in the XtremCache pool.

On each virtual machine, we configured the LUNs that will be accelerated by the XtremCache as source LUNs for the XtremCache device. After enabling them, data is cached just as it is in a physical environment. The source LUN can be any LUN in the virtual machine, such as Virtual Machine Data file for VMware (VMDK) or RDM.



Figure 25. Architecture of the VSPEX Proven Infrastructure for XtremCache deployment on VMware



Architecture of XtremCache deployment on Hyper-V

Figure 26 shows the validated architecture for an XtremCache deployment on a VSPEX Private Cloud with Hyper-V. In a Hyper-V environment, the XtremCache is deployed on the Hyper-V host and managed from this level. The I/O issued by the virtual machines is accelerated at the Hyper-V level. If there are multiple VHDXs on the same LUN in the Hyper-V host, they will all be accelerated because the XtremCache source LUN is configured at the Hyper-V host level.

If a VHDX is used in Hyper-V, the source LUN for XtremCache on the Hyper-V host should contain only VHDXs that need to be accelerated.

Figure 26. Architecture of the VSPEX Proven Infrastructure for XtremCache deployment on Hyper-V



XtremCache for SQL Server OLTP database

In a SQL Server environment, the storage LUNs that host the database data files for the OLTP database are most likely to benefit from XtremCache acceleration.

The read-to-write ratio of a typical SQL Server OLTP database data file ranges from 70:30 to 90:10, making the database data file LUN ideal for XtremCache acceleration. In the example use case described in this section, we tested an active OLTP database with a read-to-write ratio of 90:10. Using about a 100 GB cache to accelerate a 1 TB OLTP database reduced the read latency by more than half.

XtremCache is proven to be highly scalable and reliable. It can relieve the I/O processing pressure from the storage system and boost the disk read operations driven by the host, even in virtual ESXi-based environments. XtremCache increases the overall transaction rate of SQL Server and significantly reduces disk latencies with minimal impact on system resources.

XtremCache in SQL Server OLTP environments provides the following benefits:

XtremCache can reduce SQL Server storage response time.

The XtremCache host driver has minimal impact on server and virtual machine system resources. In testing, the system resources were mostly consumed by the SQL Server workload. The XtremCache driver overhead was negligible—0.4 percent CPU usage in this example use case.

With a highly optimized, multitier storage system, XtremCache can offload read I/O processing from the storage array while reducing disk latencies, thus enabling higher transactional throughput and enabling the EMC storage array to consume even more workload.

With less optimized, two-tier storage configurations, XtremCache can significantly boost SQL Server transactions and lower overall host disk latency. It can address “hot-spots” in the datacenter and alleviate possible storage bottlenecks.

We observed a performance boost immediately after the LUNs were added to the XtremCache pool. Performance reached a steady state in approximately one hour for all 16 LUNs hosting a 3 TB database file.

XtremCache is a server-based cache. Introducing XtremCache to a storage environment does not require any changes to the application or storage system layouts.

Because XtremCache is a caching solution rather than a storage solution, there is no need to move data. Therefore, you do not risk having inaccessible data if the server or the PCIe card fails.

XtremCache minimizes CPU overhead in the server by offloading flash management operations from the host CPU onto the PCIe card.

Managing and monitoring XtremCache in a vSphere environment is easy. After configuration, XtremCache requires no user intervention and continuously adjusts to meet the needs of the application workload.

Benefits of XtremCache in a SQL Server OLTP environment



Based on the XtremCache Performance Predictor, in a SQL Server OLTP environment running a heavy OLTP workload, the primary database LUNs can benefit most from XtremCache acceleration. The log LUNs and tempdb LUNs are write-heavy and should not be used with the XtremCache.

In summary, in a typical SQL Server OLTP environment:

You should use XtremCache Performance Predictor to estimate the benefits for adding the XtremCache to SQL server environment.

The read-intensive database data file LUNs generally have heavy workload, subjected to a high-read skew, and are good candidates for XtremCache.

SQL Server OLTP data files experience constant random reads and contribute to the overall duration of transaction times. Data files also experience regular bursts of write activity during a checkpoint operation. Using XtremCache to perform cache reads and avoid an I/O workload on the EMC array enables the array to consume those burst writes faster and avoid any read delays for transactions.

Log LUNs and tempdb LUNs in OLTP databases are write-intensive and typically do not benefit from XtremCache.

In SQL Server AlwaysOn environments, the secondary databases do not need to be accelerated unless a specific performance requirement justifies the use of XtremCache.

Set the page size to 64 KB in the XtremCache to accommodate the large I/O for the SQL Server database.

If the workload is not expected to increase after deploying XtremCache in the VSPEX Proven Infrastructure, there is no need for additional system resources such as memory or CPU.

With a read-to-write ratio of 90:10 in the OLTP database LUNs, for each 1 TB of database, an XtremCache of 100 GB or more would significantly improve the OLTP query performance and read operations.

The example use case deployed XtremCache to accelerate OLTP performance in a multiuser SQL Server 2012 database virtualized with the VMware environment. Two ESXi servers each hosted one SQL Server virtual machine. One of the SQL Server virtual machines used a 700 GB SLC XtremSF card. The other server did not have XtremCache configured.

The environment is based on a multitier storage solution that is controlled and optimized by EMC Fully Automated Storage Tiering for Virtual Pools (FAST VP).

The solution design includes the following components and features as shown in Figure 27:

Two vSphere ESXi servers, each hosting one SQL Server virtual machine

XtremCache enabled on the primary SQL Server virtual machine

Best practices

Use case design and deployment



Figure 27. Architecture design for XtremCache enabled SQL Server virtual environment

Deployment scenarios

Figure 28 shows the XtremCache deployment for this use case. All the database file LUNs on the primary server are configured as source LUNs for XtremCache acceleration; tempdb LUNs and log LUNs are excluded. The secondary server does not have XtremCache configured.



Figure 28. SQL Server AlwaysOn XtremCache deployment

In this solution, we configured one 278 GB XtremCache. All 16 source data devices were associated with the cache device, as shown in Figure 28.

Configuration is straightforward using the wizards in the VSI integrated plug-in. If preferred, you can use the command line from the Windows virtual machine.

Perform the following steps to configure the XtremCache for the database LUNs in the virtual machine:

1. Use vCenter Server to create a VMFS datastore, and then create XtremCache pool with the XtremSF card in the ESXi server.

2. Create the XtremCache device from the Cache pool and assign it to the virtual machines through the VSI plug-in for XtremCache.

3. Add the source devices to the enabled XtremCache device to accelerate their performance.

Any source device can be stopped temporarily or removed from the caching operation without affecting other source devices.

XtremCache boosts system performance

After enabling XtremCache for the first time, the performance boost was visible immediately.

XtremCache started to take effect as soon as it was enabled with the devices needing a performance boost added into the cache pool. It took approximately one hour in this environment to reach the maximum performance boost.

We tested XtremCache for SQL Server in both a two-tier and three-tier configuration. Figure 29 shows the read and write IOPS for the primary SQL Server before and after enabling XtremCache in a two-tier storage system.

Configuration of XtremCache in the VMware environment

Test results



Figure 29. Performance boost after enabling XtremCache

After the system reached the steady state, the system performance was stable during the 24-hour testing period. XtremCache reduces SQL Server response time

XtremCache significantly reduced the SQL Server response time for high response time transactions in both the two-tier and three-tier configurations.

The XtremCache host driver had a minimal impact on the server and virtual machine system resources. The read latency reduced by approximately 50 to 70 percent after we enabled XtremCache. We observed a similar result with the transaction latency, where XtremCache also significantly lowered the response time of high latency transactions.

Without XtremCache, the two-tier configuration can support only 14,000 IOPS. With XtremCache, it can fully support a 24,000 IOPS load with a 90:10 read-to-write ratio.

XtremCache significantly lowered the I/O activities on the storage array (about 10,000 IOPS) in the three-tier configuration, thus enabling the storage system to support more server I/O requests.

0

2

4

6

8

10

12

0

5,000

10,000

15,000

20,000

late

ncy

(m

s)

IOP

S

IOPS and latency change after enabling XtremCache

IOPS latency ( ms)

Baseline | XtremCache Enabled Steady state



Table 9 shows the detailed test results for all the test scenarios in this solution. Table 9. Performance data with OLTP load

Performance

Three-tier storage Two-tier storage

Without XtremCache

With XtremCache

Without XtremCache

With XtremCache

SQL Server virtual machine CPU 67.45% 67.85% 15.50%* 51.43%

ESXi CPU 77.80% 78.20% 24.63%* 65.57%

Client transactions per second (TPS)

2,193 2,585 1,225 2,229

SQL Server virtual machine IOPS 23,938 23,916 14,123 23,602

Array front-end IOPS 24,698 14,987 15,475 13,798

Latency (ms) (read/write/transfer) 4/1/4 2/2/2 11/1/10 4/3/4

* CPU usage was lower because the storage bottleneck created in this test limited the client load that can be pushed to the system.

XtremCache for Exchange Server

In an Exchange Server environment, the Exchange database LUNs are most likely to benefit from XtremCache acceleration.

The performance of the database can be improved by using 10 GB of XtremCache for each 1 TB of Exchange data in the Mailbox server virtual machines in the example use case described in this section.

Even though the typical Exchange Mailbox workload has about a 60:40 read-to-write ratio and a large I/O size, the working set of the Exchange databases is very small. This means that the Mailbox workload performance can be dramatically improved when a small slice of XtremSF is configured as XtremCache for the Mailbox database LUNs. The high I/O skew in this use case also makes it a good candidate for deduplication with limited memory and CPU consumption.

Using XtremCache in an Exchange environment offers many benefits:

XtremCache improves Exchange performance by reducing read latencies and offloading read operations from the back-end storage.

XtremCache helps to maximize I/O throughput for Exchange workloads without changing or adding any additional storage resources.

XtremCache reduces bandwidth requirements through deduplication features, offloading write processing from the Exchange back-end storage.

Benefits of XtremCache in an Exchange environment



XtremCache can be integrated with vSphere for virtual machine migration that has an XtremCache device attached. With proper configuration, the applications can resume the accelerated state after virtual machine auto-migration occurred.

XtremCache has little impact on system resources such as CPU and memory.

The initial warm-up period for XtremCache with Exchange-simulated workloads varies for each environment. In this solution, the effect of XtremCache was observed immediately after it was enabled. It reached a steady state in approximately 30 minutes for all Exchange accelerated database LUNs with 15 TB of data.

Integration with the VSI plug-in for VMware makes XtremCache easy to manage and monitor in a virtualized environment.

XtremCache is designed to minimize CPU overhead in the server by offloading flash management operations from the host CPU onto the XtremSF PCIe card.

With an Exchange workload, XtremCache can relieve I/O processing pressure from the storage system and boost the disk read operations driven by the host.

XtremCache increases the overall Exchange application IOPS and significantly reduces disk latencies with minimal impact on system resources.

Using XtremCache enables customers to configure Exchange for high performance and low cost without making trade-offs.

Managing and monitoring XtremCache in a vSphere environment is easy. After configuration, XtremCache requires no user intervention and continuously changes to meet the application workload requirements.

In an Exchange environment configured with Database Availability Groups (DAGs) (for both active and passive copies of DAG), and based on the XtremCache performance predictor tool results, the LUNs for the databases can benefit most from XtremCache acceleration.

More importantly, the working set for Exchange database is relatively small; thus, the XtremCache size needed for Exchange server acceleration is also small. In this use case, every 1 TB of Exchange data requires only about 10 GB of XtremCache. Enabling XtremCache acceleration for both active and passive databases also improves the performance. If there is a DAG failover, XtremCache is already warm when the DAG fails over and the whole Exchange environment shows almost no performance impact. The LUNs for the database log should be excluded because of their sequential workload.

In summary, in a typical Exchange environment:

Use XtremCache Performance Predictor to estimate the benefits of adding XtremCache to the Exchange environment.

In Mailbox virtual machines, typically both active and passive database file LUNs with a heavy workload are good candidates for XtremCache source LUNs. XtremCache also helps improve the performance even in a DAG failover scenario.

Best practices



You should typically exclude log LUNs from XtremCache.

Set the page size to 64 KB in XtremCache to accommodate the large I/O size of the Exchange Server.

For each Exchange virtual machine, for every 1 TB of Exchange data, configure about a 10 GB XtremCache to significantly improve the Mailbox server performance.

The example use case deployed XtremCache to accelerate the performance of Exchange 2010 in a DAG configuration with two database copies virtualized with the VMware environment.

We installed two 700 GB SLC XtremSF cards on the vSphere ESXi servers hosting six Exchange Mailbox server virtual machines.

In testing, the system IOPS improved by over 26 percent, and read latencies decreased by about 50 to 70 percent.

We also tested the environment for deduplication with little additional system resource consumption. When enabling XtremCache deduplication for Exchange Server, you can reduce the CPU usage by up to 50 percent in certain workloads, with a drop of up to 30 percent in the write IOPS to the back-end array.

Figure 30 shows the solution design, which included the following components:

A vSphere HA cluster consisting of two vSphere ESXi servers, each hosting three Exchange Mailbox server virtual machines

Two copies of the DAG database configured on different Mailbox servers

XtremSF installed on both ESXi servers in the HA cluster

Each Exchange Mailbox server virtual machine configured with a 50 GB XtremCache for their 5 TB databases (including both active and passive DAG copies).




Figure 30. Architecture design for XtremCache-enabled Exchange virtual environment


Figure 31 shows the XtremCache deployment for the Exchange use case. We configured all database LUNs for active and passive copies on the virtual machines as source LUNs for XtremCache acceleration. The log LUNs were excluded mostly because of their write and sequential I/O.



Figure 31. XtremCache deployment for Exchange 2010 on vSphere

In this deployment, for each virtual machine with 5 TB of storage, we deployed 50 GB of XtremCache. We configured the rest of the XtremCache capacity to support the vMotion failover.

The configuration of XtremCache for an Exchange Mailbox server in a VMware environment is similar to the SQL Server configuration previously shown in Figure 28.

In addition, for this use case, we configured deduplication and vMotion migration. You can configure the XtremCache data deduplication feature for the Exchange Mailbox server virtual machines. Data deduplication eliminates redundant data by storing only a single copy of identical chunks of data while, at the same time, providing access to the data from the cache. Deduplication also helps to reduce storage and bandwidth requirements and extend the life expectancy of the cache device.

Configuring the XtremCache device with data deduplication

To enable data deduplication for the XtremCache device, follow these steps:

1. Select the Use Data Deduplication checkbox in the Add XtremCache Device wizard, when adding the XtremCache device to a virtual machine.




2. Select the expected data deduplication gain based on your Exchange workload type, as shown in Figure 32.

Figure 32. Enabling data deduplication on the XtremCache device

You can also enable data deduplication using the XtremCache CLI on the Windows client machine by running the following command:

vfcmt add -cache_dev harddisk13 –set_page_size 64 –set_max_io_size

64 –enable_ddup –ddup_gain 20

Where: Is:

harddisk13 A configured operating-system cache device for the virtual machine

ddup_gain 20 The deduplication gain percentage for the system cache device on the virtual machine

After adding the deduplication-enabled XtremCache device, add the Exchange database LUNs as source devices to the XtremCache device for performance acceleration.

To determine the appropriate data deduplication gain for your Exchange workload, review the XtremCache statistics information in the XtremCache VSI plug-in or use the CLI on the Windows server. After the cache warm-up, follow these recommendations:

Calculate the observed deduplication hit ratio and compare it with the configured ratio.

Calculate the observed deduplication hit ratio by dividing the Write Hits by the Writes Received. This is the amount of duplicated data in the cache.

If the observed ratio is less than 10 percent, turn off deduplication or reconfigure the deduplication gain to zero percent. To benefit from the extended life of the cache device, keep deduplication enabled.



If the observed ratio is over 35 percent, raise the deduplication gain to match the observed deduplication.

If the observed ratio is between 10 and 35 percent, leave the deduplication gain as it is.

To change the configured ratio, remove the XtremCache device from the Exchange Mailbox server virtual machine, and add it back again with a new deduplication percentage value. To do this, use the VSI plug-in or the CLI command (vfcmt add -cache_dev), as described previously in this section.

Migrating an Exchange virtual machine with XtremCache device

It is possible to move an Exchange virtual machine that has an XtremCache disk from one vSphere host to another. Under a typical scenario, without an XtremCache device, you can use the native vSphere migrate command to move a virtual machine from one host to another. This is possible because in a typical scenario the virtual machine’s datastores and RDMs are shared resources.

In the XtremCache environment, however, the XtremCache datastore is mapped to its local host flash drive. Consequently, this datastore is accessible only to that host and the native vSphere migrate command is not supported. Instead, use the EMC XtremCache VSI plug-in to perform the virtual machine migration with the XtremCache device attached.

Multiple forms of migration are available. The form of migration that you choose determines the steps you perform to complete the migration.

Before you begin, ensure that your system meets the following prerequisites:

The target datastore has enough available capacity for the new device.

There are no additional DAS flash-based devices for the host virtual machine.

Only one XtremCache device is configured on the host virtual machine.

The virtual machine you want to migrate is not currently being migrated.

The source host and the target host must be able to communicate with each other, so ensure the IP and Domain Name System (DNS) have been properly configured.

Recovering Exchange data from a snapshot

If you are using backup software that performs snapshots of Exchange LUNs accelerated by XtremCache, follow specific procedures when restoring data from those snapshots to ensure data integrity.

If an Exchange LUN snapshot is taken on the array, and later used to roll back changes on the source LUN, the server will not be updated with the changes. This could result in the cache supplying data that may not been updated with the contents of the snapshot.

To prevent this from occurring, when recovering from the snapshot, perform the following steps:

1. Quiesce the application that is accessing the source volume using application-specific tools, such as EMC Replication Manager.



2. Flush the data in the host buffers using an appropriate command, such as admsnap flush, and unmount the file system.

3. Invalidate the contents of the source device by using the purge -source_dev command.

4. Perform the snapshot restore operations on the array.

5. After the restore is complete, remount the file system, as necessary.

XtremCache acceleration test results

We observed consistent reductions in read latencies and increased user IOPS with all workload types when we enabled XtremCache to accelerate performance for the database LUNs. Even 300-message workloads that experienced over 20 ms read latencies without XtremCache became a normal steady workload with reduced latencies and increased IOPS with XtremCache enabled. This extreme workload was expected to fail as the storage and Exchange virtual machine resources were originally designed for 150-message workloads.

Figure 33 provides additional details for each test performed. Highlights of the observed test results include:

A 150-message per user per day workload achieved a 51 percent reduction in read latencies (by 6.4 ms) and a 14.6 percent increase in user IOPS (by 224 IOPS).

A 250-message per user per day workload achieved a 69.3 percent reduction in read latencies (by 11.1 ms) and a 12.8 percent increase in user IOPS (by 275 IOPS).

A 300-message per user per day workload achieved a 56.8 percent reduction in read latencies (by 12.5 ms) and a 12 percent increase in user IOPS (by 346 IOPS).

Test results



Figure 33. Exchange 2010 performance with XtremCache and LoadGen workload

Performance with XtremCache data deduplication

To validate Exchange performance with XtremCache inline data deduplication, we performed validation on one Exchange virtual machine with 5,000 users. We performed a series of Microsoft Exchange Load Generator (LoadGen) tests, with each test lasting eight hours and with multiple workload profiles, to see the effect of data deduplication. We monitored the XtremCache statistics to determine the appropriate deduplication ratio for each workload. With the LoadGen workloads we generated, we observed that a 30 percent deduplication ratio would be more effective than the default 20 percent. Figure 34 shows the deduplication ratio observed during testing.

Figure 34. XtremCache statistics with data deduplication

Note: The LoadGen workload does not represent the actual workload in your specific production environment. The results observed and recommendations provided here are based on our lab configuration and results only. Ensure that you configure your environment based on your particular workload requirements and characteristics.



Deduplication test results summary

In Figure 35 and Figure 36, the XtremCache data deduplication test results with multiple workload profiles for the Exchange 2010 Mailbox server show:

Decreased Exchange Server CPU utilization with each workload

Slightly increased write latencies due to XtremCache analysis and processing of the duplicated data



Figure 35. Exchange server CPU utilization with XtremCache data deduplication

Figure 36. Exchange server disk latencies with XtremCache data deduplication



Analysis of the back-end VNX storage array shows that when we enabled deduplication on the server, the writes to the VNX array were reduced. In Figure 37, the write activity was reduced from 90 IOPS to around 65 IOPS for one of the database LUNs, which is about a 27.7 percent difference.

Figure 37. Exchange database LUN performance with XtremCache data deduplication

XtremCache for SharePoint

For the SharePoint environment, content database and crawl database LUNs are most suitable for XtremCache acceleration.

A typical SharePoint content database workload has a 70:30 read-to-write ratio, making it an ideal candidate for XtremCache acceleration. With two 600 GB XtremCache devices configured on two 700 GB XtremSF cards, the database latency can drop to less than one third during a full crawl.

This use case demonstrates the following results:

XtremCache offloads the read workload of the SharePoint content database workload during the crawl process from the storage array to the server.

XtremCache improves the crawl performance by lowering the latencies in the content database of the SharePoint farm in a virtualized environment.

XtremCache has little impact on system resources such as CPU and memory.

Integration with the VSI plug-in for VMware vSphere vCenter makes XtremCache easy to manage and monitor in a virtualized environment.

In a SharePoint environment, based on the XtremCache Performance Predictor tool, the LUNs for the content databases during the crawl process can benefit most from XtremCache acceleration. The database file LUNs for the content database are, therefore, good candidates for the XtremCache source LUNs. Exclude the log LUNs and tempdb LUNs from XtremCache as they are mostly write-heavy.

In summary, in a typical SharePoint Farm:

Use XtremCache Performance Predictor to estimate the benefits of adding XtremCache to SharePoint Farm.

Benefits of XtremCache in a SharePoint environment

Best practices



The content database files LUNs and crawl database LUNs with a heavy workload are good candidates for the XtremCache source LUNs.

Log LUNs and tempdb LUNs in the SharePoint farm are excluded from the acceleration of XtremCache.

Set the page size to 64 KB and the maximum I/O size to 128 KB in the XtremCache to accommodate the large I/O size of the content and crawl databases, especially when NFS is in use.

For each 1 TB of the content database, an XtremCache of 200 GB or more can significantly improve the OLTP query performance.

The example use case deployed a virtualized SharePoint 2010 farm with 1.8 TB content databases in one SQL Server 2012 virtual machine in a vSphere 5.1 virtualized environment, configured with two 700 GB XtremSF cards. You can improve the performance of the SharePoint crawl by:

Deploying 600 GB XtremCache in the SQL Server virtual machine

Configuring all the content database file LUNs and the crawl database file LUNs to be accelerated by the XtremCache

The latency for these LUNs decreases dramatically and the crawl performance improves by more than 20 percent.

The configuration of XtremCache for SharePoint in a VMware environment is similar to the SQL Server configuration. Only the SQL Server virtual machine in the SharePoint farm needs XtremCache acceleration.

The solution design includes the following components, as shown in Figure 38:

XtremSF installed on vSphere ESXi servers hosting the SQL Server virtual machine for SharePoint Server

XtremCache enabled on the SQL Server virtual machine, only configured for the content databases and the crawl databases

Storage tiers with FAST VP enabled




Figure 38. Architecture design for XtremCache enabled SharePoint environment


Figure 39 shows the XtremCache deployment for this use case. All the content database file LUNs are configured as source LUNs for XtremCache acceleration, but tempdb LUNs and log LUNs are excluded.



Figure 39. XtremCache deployment for SharePoint 2010 on vSphere

In this solution, two cache devices with a usable size of 600 GB out of the 700 GB XtremCache card are configured for the content database virtual machine. All the LUNs for the content databases data file and the crawl database data file are associated with the two cache devices.

During the crawl process, the content database data file is 100 percent random read and the crawl database data file is around 60 percent read. Set the I/O page size for the cache device to 64 KB (the default is 8 KB) and the maximum I/O size to 128 KB (the default is 64 KB).

The Read Hit rate for the content database during a full crawl is about 70 to 75 percent, and the crawl database is around 40 percent.

The hard disks that store the content databases all have an over 70 percent Read Hit rate. The Read Hit rate is around 40 percent for the crawl database hard disk.

The latency of the content databases and crawl database dropped dramatically after we enabled the cache device, as shown in Figure 40. Note that the property database is not configured as source devices for cache. The latency drop contributed to the property database improvement because it was in the same disk pool in the storage array. As the I/O on the backend for the content and crawl database were offloaded to


Test results



the XtremCache, a side effect was an improvement in the latency for the property database.

Figure 40. Content database latency dropped after enabling XtremCache

The full crawl duration decreased by 21.2 percent when XtremCache was enabled, as shown in Figure 41

.

Figure 41. Full crawl performance improved after enabling XtremCache



XtremCache for Oracle OLTP database

In the VSPEX for virtualized Oracle environment, the database LUN for the OLTP database is most likely to benefit from XtremCache acceleration.

We tested a database with a read-to-write ratio of 70:30. Within an XtremCache of 200 GB to accelerate 1 TB of the database LUN, the transaction rate almost doubled.

Similar to the application environments described previously, the VSPEX for virtualized Oracle environment will benefit from XtremCache as a server-based cache. Introducing the XtremCache virtual infrastructure does not require any changes to the application or storage system layouts. Because XtremCache is a caching solution rather than a storage solution, there is no need to move data. Therefore, your data is not at risk of becoming inaccessible if the server or the PCIe card fails. XtremCache is designed to minimize CPU overhead in the server by offloading flash management operations from the host CPU to the PCIe card. In a virtualized Oracle OLTP environment, XtremCache:

Delivers an 80 percent improvement in transactions per minute (TPM) compared to the baseline without any changes to applications

Maintains the integrity of and protects the data

In an Oracle Database 11g R2 environment, based on the XtremCache Performance Predictor tool, the database file LUNs can benefit most from XtremCache acceleration and are good candidates for the XtremCache source LUNs.

In summary, in a typical Oracle OLTP environment:

Use the XtremCache Performance Predictor tool to estimate the benefits of adding XtremCache to the environment.

The database file LUNs with a heavy workload are good candidates for the XtremCache source LUNs.

Log LUNs and tempdb LUNs in the OLTP databases are excluded from the acceleration of XtremCache.

For each 1 TB of database with a read-to-write ratio of 70:30, an XtremCache of 200 GB or more can significantly improve the performance of the database.

The example use case deployed a standard TPC-C-like OLTP workload, with a 1.2 TB database and a 70 to 30 percent read/write mix on Oracle Database 11g R2 on a Red Hat Enterprise Linux 5 virtual machine virtualized with vSphere 5.1. By deploying 250 GB of usable XtremCache in the Oracle virtual machine from a single 350 GB XtremSF card, the performance of the workload can be dramatically improved. The transactions per minute improved 80 percent compared with the same environment without XtremCache.

Benefits of XtremCache in an Oracle environment

Best practices




The solution design includes the physical components shown in Figure 42:

A single vSphere ESXi server hosting one Oracle Database 11g R2 server on a Red Hat Enterprise Linux 5 virtual machine

A 1.2 TB database on eight VMDK LUNs for the database files and two VMDK LUNs for the logs

XtremSF installed on the ESXi server with a 250 GB XtremCache configured for the Oracle virtual machine

We configured only database VMDKs as source LUNs for XtremCache. We excluded the log LUNs and the tempdb LUNs.

Figure 42. Architecture design for XtremCache enabled Oracle 11g R2 environment




Figure 43 shows the XtremCache deployment for the Oracle use case. We configured all of the database VMDK LUNs on the virtual machines as source LUNs for XtremCache acceleration. We excluded log LUNs because of their write-intensive nature. In this deployment, we configured 250 GB of XtremCache for caching 1.2 TB of the OLTP database.

Figure 43. XtremCache deployment for Oracle 11g R2 on vSphere

Configuring XtremCache for Oracle in a VMware environment is similar to configuring the other application environments described in the previous sections.

Figure 44 compares the overall system throughput (in TPM) of the baseline and XtremCache-enabled environments. The availability of the hot data in the server’s XtremCache resulted in an 80 percent improvement in transactions per minute.

Test results



Figure 44. OLTP TPM improvement

XtremCache for private cloud

This use case deployed the XtremCache to accelerate performance of the following applications in a private cloud environment virtualized with VMware:

Oracle Database 11g R2 OLTP database

SQL Server OLTP database

SQL Server decision support system (DSS) database

SQL Server 2012 cluster

In the Oracle and SQL Server OLTP virtual machines, we configured the XtremCache based on the principals described in the previous application-specific sections. The cluster support configured XtremCache for both active and passive databases. SQL Server DSS uses XtremSF storage in a split configuration for the tempdb of the DSS database.

With a comprehensive private cloud environment, XtremCache and XtremSF proved to be flexible and were able to deliver the expected performance improvement for all the applications in different configurations.

XtremCache is proven to complement FAST VP for performance improvement of both the SQL Server and Oracle OLTP databases.

The tempdb, supported by XtremSF in the database for the DSS workload, gets a performance boost from the XtremSF.



This EMC solution has shown the implementation of multiple critical applications in a VMware private cloud environment, supported by XtremSF and XtremCache. Each application had different workload characteristics and placed varying demands on the underlying storage. XtremCache provided better performance for the applications that involve heavy read I/O.

The benefits of XtremCache in a private cloud environment include the following:

Performance optimization—accelerating application-specific performance at the host level using EMC XtremSF cards:

With a three-tier FAST VP configuration, XtremCache offloads the IOPS of the array significantly. The array can be free for other I/O requests.

With a two-tier FAST VP configuration, XtremCache reduces disk latencies and response times, enabling a higher transaction throughput.

XtremCache reduces disk latencies and response time, enabling higher transaction throughput by offloading much of the read I/O traffic from the storage array.

XtremCache caches the read I/O so the data is not at risk of being inaccessible if the server or the XtremCache card fails.

Using XtremSF storage in a split-card configuration for the tempdb of the DSS database boosts the performance of the tempdb.

XtremCache in a virtualized environment is easy to manage and monitor due to its integration with the VSI plug-in to VMware vSphere vCenter.

XtremCache deduplication helps to reduce the footprint on bandwidth.

In this private cloud environment, XtremCache demonstrated both flexibility and ease of management in a comprehensive configuration, improving performance while having little impact on system resource consumption.

In a private cloud environment, you need to consider multiple applications. Follow the application-specific best practices, particularly for the deployment of XtremCache in a heterogeneous environment:

Always use the XtremCache Performance Predictor tool to determine which application can benefit from XtremCache the most.

Allocate XtremCache for the most critical application virtual machine first, and then consider the rest of the virtual machines.

Consider placing virtual machines on a different physical server to optimize the capacity of XtremSF.

MLC XtremSF (alone or in split-card mode) can be used as a tempdb for data warehouse or DSS types of databases. To improve query performance, consider allowing at least 200 GB of tempdb space for every 1 TB of database.

Benefits of XtremCache in a private cloud environment

Best practices



In the example use case, Microsoft SQL Server 2012 (two OLTP and one DSS), Oracle Database 11g R2 (OLTP), and Microsoft SQL Server failover clustering are all on the virtualized environment. These applications ran on virtual machines in a VMware vSphere 5 environments on FAST VP-enabled EMC storage, which continually monitors and tunes performance by relocating data across tiers based on access patterns and predefined FAST policies.

We deployed XtremSF on both ESXi servers, one configured in a split-card mode. We configured XtremCache to support the OLTP databases for caching purposes, while using the remaining XtremSF capacity for the storage of tempdb in the DSS database.

Load generation tools drove these applications simultaneously to validate the infrastructure and function of XtremCache acceleration to the data LUNs of the OLTP application.

The solution design included the following components, as shown in Figure 45:

Two vSphere ESXi servers, one hosting the Oracle Database 11g R2 server and a SQL Server virtual machine as part of Microsoft Server failover cluster; the other hosting the other SQL Server of the MSCS, two SQL Servers with OLTP, and one SQL Server with a DSS workload.

XtremSF configured in split-mode is used as tempdb storage for the SQL Server virtual machine with the DSS workload.

XtremCache enabled on all other virtual machines.

FAST VP-enabled storage tiers.




Figure 45. Architecture design for XtremCache-enabled private cloud environment with multiple applications


Table 10 shows the XtremCache deployment for the private cloud use case. The configuration of the database LUNs follows the same best practices as the application-specific use cases, such as source LUNs for XtremCache acceleration. We excluded the log LUNs because they have mostly write and sequential I/O. We used XtremSF in split mode for the DSS tempdb store to accelerate the DSS workload.



Table 10. XtremCache deployment in a private cloud environment

XtremCache allocation per application/virtual machine

ESXi 01 (allocation unit: GB)

ESXi 02 (allocation unit: GB)

Configuration details

Oracle OLTP 600 0 2 TB database under 1,800 Swingbench sessions

DSS 0 200 2.5 TB database with DSS workload

SQL OLTP 01 0 200 1.75 TB with OLTP workload

SQL OLTP 02 0 200 1.12 TB with OLTP workload

Total 600 600

The configuration of XtremCache for a private cloud in a VMware environment needs to follow all the guidelines for each individual application, such as SharePoint, SQL Server, Exchange, and Oracle.

For more information, refer to the EMC XtremCache Installation and Administration Guide.

Test result for XtremSF in split mode used as the SQL Server tempdb for a DSS workload

In the solution, a 200 GB XtremCache was taken from the 700 GB XtremSF card and was used for the tempdb database data and log storage to accelerate performance. The SQL Server tempdb was heavily used as a temporary table store for sorting, row versioning, and so on. As the tempdb store for a DSS workload, the XtremCache DAS can:

Lower the peak latency of the tempdb data LUN from tens of milliseconds to less than 20 ms.

Lower the average tempdb data LUN latency from tens of milliseconds to one ms.

Test results for XtremCache deduplication

The test result shows:

The Oracle deduplication hit ratio was about 4 percent.

The SQL OLTP deduplication hit ratio was about 3 percent.

The recommended deduplication settings for a structured database such as Oracle or SQL Server are:

If the observed ratio is less than 10 percent, turn off the deduplication or reconfigure the deduplication gain to zero percent, to benefit from the extended cache device life.


Test results



If the observed ratio is over 35 percent, raise the deduplication gain to match the observed deduplication.

If the observed ratio is between 10 and 35 percent, leave the deduplication gain as it is.

Figure 46 shows that the deduplication hit ratio of SQL Server is 3 percent.

Figure 46. Deduplication statistics for SQL Server OLTP

Test results for two-tier storage

Table 11 shows the performance summary for the private cloud environment. For Oracle, the response time dropped from 35 ms to 3 ms. For SQL Server, the response time dropped from over 20 ms to 3 ms. All database transaction rates improved, with the SQL Server OLTP gaining the most (which was a three times transaction rate increase using part of the 700 GB caching space).

The increased CPU usage was largely due to the increased workload. When the workload is kept the same or is not greatly increased, CPU usage does not increase much. This is seen in the case of ESXi 01, which hosts Oracle—with only a moderate increase in the workload, the CPU usage did not greatly increase.



Table 11. Performance summary for the private cloud environment

Component Performance Two tiers configured without XtremCache

Two tiers configured with XtremCache

SAN storage Array IOPS 24,000 10,000

Busy% 60% 30%

ESXi 01 Avg. CPU utilization 16% 21%

ESXi 02 Avg. CPU utilization 2% 40%

Oracle OLTP Swingbench Order Entry (SOE) TPS

6,653 8,590

Swingbench Avg. Oracle response (ms)

35 3

SQL Server SQL01 Latency (ms) read/write/transfer

22/4/21 3/2/3

SQL02 Latency (ms) read/write/transfer

21/4/21 2/3/2

SQL01 vCPU utilization 1.20% 69.84%

SQL02 vCPU utilization 1.46% 63.04%

Client TPS (total) 56 162

TPS 2,073 6,054

XtremCache Hit Rate SQL01 N/A 69%

SQL02 N/A 82%

XtremCache Read Rate

SQL01 N/A 93%

SQL02 N/A 89%

Chapter 6: References


Chapter 6 References


EMC documentation ............................................................................................. 91

Other documentation ........................................................................................... 92

Links ................................................................................................................... 92



EMC documentation

The following documents, available from the EMC Online Support or EMC.com websites, provide additional and relevant information. If you do not have access to a document, contact your EMC representative.

EMC VNX Virtual Provisioning—Applied Technology

EMC VNX Series Unified Storage Systems—Specification Sheet

EMC VNX Family—Data Sheet

EMC Mission Critical Infrastructure for Microsoft SQL Server 2012—White Paper

EMC Storage Optimization and High Availability for Microsoft SQL Server 2008 R2 - EMC VNX5700, EMC FAST Suite, VMware vSphere 5—White Paper

EMC Mission Critical Infrastructure for Microsoft SQL Server 2012 - EMC Symmetrix VMAX 10K, EMC FAST VP, SQL Server AlwaysOn Availability Groups, VMware vSphere—White Paper

Accelerating Microsoft Exchange 2010 Performance with EMC XtremCache - EMC VNX Storage and VMware vSphere—White Paper

EMC VFCache Accelerates Oracle - EMC VFCache, EMC Symmetrix VMAX and VMAX 10K, Oracle Database 11g—White Paper

EMC VFCache Accelerates Virtualized Oracle - EMC VFCache, EMC Symmetrix VMAX and VMAX 10K, VMware vSphere, Oracle Database 11g—White Paper

EMC VFCache Accelerates Oracle - EMC VFCache, EMC VNX, EMC FAST Suite, Oracle Database 11g—White Paper

EMC VFCache Accelerates Microsoft SQL Server - EMC VFCache, EMC VNX, Microsoft SQL Server 2008—White Paper

EMC VFCache Accelerates Virtualized Oracle - EMC VFCache, EMC Symmetrix VMAX, EMC FAST Suite, VMware vSphere, Oracle Database 11g—White Paper

For additional information, visit the following spaces on EMC.com:

XtremCache

VNX Series

At the time of publication, the following related documents were available:

XtremCache Installation and Administration Guide v2.0.1

XtremCache Installation Guide for VMware 2.0.1

XtremCache Troubleshooting Guide 2.0.1

XtremCache Troubleshooting Guide for VMware v2.0.1

XtremCache VMware VSI Plug-in Guide 2.0.1

Introduction to EMC VFCache

EMC VFCache—Data Sheet

VFCache Installation and Administration Guide for Windows and Linux

https://support.emc.com/

http://www.emc.com/resource-library/resource-library.htm

http://www.emc.com/collateral/hardware/white-papers/h8222-vnx-virtual-provisioning-wp.pdf

http://www.emc.com/collateral/software/specification-sheet/h8514-vnx-series-ss.pdf

http://www.emc.com/collateral/hardware/data-sheets/h8520-vnx-family-ds.pdf

http://www.emc.com/collateral/hardware/white-papers/h10507-mission-critical-sql-server-2012.pdf

http://www.emc.com/collateral/hardware/white-papers/h8987-mssql-vnx5700-wp.pdf

http://www.emc.com/collateral/hardware/white-papers/h8987-mssql-vnx5700-wp.pdf




http://www.emc.com/collateral/hardware/white-papers/h8888-exch-2010-storage-best-pract-design-guid-emc-storage.pdf

http://www.emc.com/collateral/hardware/white-papers/h8888-exch-2010-storage-best-pract-design-guid-emc-storage.pdf

http://www.emc.com/collateral/hardware/white-papers/h9538-vfcache-oracle-vmax-wp.pdf


http://www.emc.com/collateral/hardware/white-papers/h9537-vfcache-virtualized-oracle-vmax-wp.pdf

http://www.emc.com/collateral/hardware/white-papers/h9537-vfcache-virtualized-oracle-vmax-wp.pdf

http://www.emc.com/collateral/hardware/white-papers/h10501-vfcache-accelerates-oracle-vnx-wp.pdf

http://www.emc.com/collateral/hardware/white-papers/h10501-vfcache-accelerates-oracle-vnx-wp.pdf

http://www.emc.com/collateral/hardware/white-papers/h9539-vfcache-accelerates-microsoft-sql-server-vnx-wp.pdf

http://www.emc.com/collateral/hardware/white-papers/h9539-vfcache-accelerates-microsoft-sql-server-vnx-wp.pdf



http://www.emc.com/resource-library/resource-library.htm

http://www.emc.com/storage/vfcache/vfcache.htm

http://www.emc.com/storage/vnx/vnx-series.htm



VFCache Release Notes for Windows and Linux

VFCache Installation Guide for VMware

VFCache Release Notes for VMware

VFCache VMware Plug-in—Administration Guide

Considerations for Choosing SLC versus MLC Flash

EMC Storage Integrator for Windows Version 2.0.1—Product Guide

Microsoft Exchange 2010 on VMware—Best Practices Guide

VSI for VMware vSphere: Storage Viewer Version Product Guide 5.4

Other documentation

For additional Microsoft information, refer to the following articles:

SQL Server Best Practices

Tuning options for SQL Server when running in high performance workloads

Optimizing tempdb Performance

Microsoft Multipath I/O (MPIO) Users Guide for Windows Server 2012

For additional Oracle information, refer to the following documents:

Oracle Database Installation Guide11g Release 2 (11.2) for Linux

Oracle Database Release Notes for Linux

For additional VMware information, refer to the following document:

Installing EMC® XtremCache™ on ESXi 5.0 and 5.1

Links

For additional product information, visit the following websites:

VMware

Microsoft TechNet Library

MSDN Library

Oracle Database 11gR2 Documentation Library 11g Release 2 (11.2)

Oracle Support website (for the latest OPatch and latest PSU)

Note: The links provided in this guide were working correctly at the time of publication.

http://msdn.microsoft.com/en-us/library/cc966412.aspx

http://support.microsoft.com/kb/920093

http://msdn.microsoft.com/en-us/library/ms175527.aspx

http://www.microsoft.com/en-us/download/details.aspx?id=30450

http://docs.oracle.com/cd/E11882_01/install.112/e24321.pdf

http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=2059943

http://www.vmware.com/

http://technet.microsoft.com/en-us/library/aa991542.aspx

http://msdn.microsoft.com/library/default.aspx

http://www.oracle.com/pls/db112/homepage

http://support.oracle.com/

Appendix A: Ordering Information


Appendix A Ordering Information

This appendix presents the following topic:

Ordering XtremSF and XtremCache ....................................................................... 95

Appendix A: Ordering Information


Ordering XtremSF and XtremCache

XtremCache can be ordered through Direct Express and Channel Express. XtremCache can be ordered by itself or in combination with XtremSF hardware. Use the following model numbers when placing an order:

XtremCache

456-105-133 – ONE license for XtremCache (previously VFC-Software prior to introducing e-licensing)

456-105-135 – a pack of FIVE licenses of XtremCache( UCS blades)

XtremSF

PCIEHHS-3XXM2 (350 GB, SLC)

PCIEHHS-7XXM (700 GB, SLC)

PCIEHHM-350M (350 GB, MLC)

PCIEHHM-550V (550 GB, MLC)

PCIEHHM-700M (700 GB, MLC)

PCIEHHM-1400M (1.4 TB, MLC)

PCIEHHM-2200V (2.2 TB, MLC)

emc vspex with emc xtremsf and emc xtremsw cache · pdf fileemc vspex with emc xtremsf and emc...

Documents