empanelment and annual rate contract of suppliers for furniture ... · office furniture ,(b):...
TRANSCRIPT
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
INDIAN INSTITUTE OF TECHNOLOGY BOMBAY
EMPANELMENT AND ANNUAL RATE CONTRACT OF SUPPLIERS FOR
FURNITURE & FIXTURES 201617
MMD, IIT BOMBAY Page no. 1 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
INDEX
SECTION 1 – INVITATION OF THE BIDS
SECTION 2 ELIGIBILITY CRITERIAELIGIBILITY (A) : OFFICE FURNITURE ELIGIBILITY (B) : MODULAR / CUSTOMISED FURNITUREELIGIBILITY (C) : LAB FURNITURE / FUME HOOD
SECTION 3 – INSTRUCTIONS TO BIDDERS
SECTION 4 – TERMS AND CONDITIONS OF CONTRACT
SECTION 5 ANNEXURES
Annexure 1 : Undertaking Submission of OfferAnnexure 2 : Declaration Regarding Clean Track by BidderAnnexure 3 : Declaration for Acceptance of RFP Terms and ConditionsAnnexure 4 : Client's Experience DetailsAnnexure 5 : Declaration Of Annual Turnover And Income Tax ReturnAnnexure 6 : Bidder's Information
SECTION 6 TECHNICAL BID(A) : Office Furniture (B) : Modular furniture / Customised furniture (C) : Lab furniture / Fume hood
SECTION 7 PRICE BID(A) : Office Furniture (B) : Modular Furniture / Customised Furniture (C) : Lab Furniture / Fume Hood
SECTION 8 CHECK LIST
MMD, IIT BOMBAY Page no. 2 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
SECTION 1 – INVITATION OF THE BIDS
Sealed Tenders are invited from reputed suppliers for supply of furniture for following categories : (A): Office Furniture ,(B): Modular furniture / Customised furniture ,(C) : Lab furniture & Fume hood. The suppliers will be empanelled categorywise.
RFP No. MMD/FURNITURE & FIXTURES/RC/201617
RFP Date 16/02/2016
Advt. No. Advt. No. A49/1516
Item Description EMPANELMENT AND ANNUAL RATE CONTRACT OF SUPPLIERS FOR FURNITURE & FIXTURES
Pre Bid Meeting Date & Time 08th March 2016 at 11.00 am
PreBid Meeting Place Materials Management Division, IIT Bombay, Powai, Mumbai 400 076.
Last date & time of submission of Tender :
29th April 2016 upto 1.00 pm
Place of Submission of Bids Materials Management Division, IIT Bombay, Powai, Mumbai 400 076.
Submission of Bids Two Bid System : The two bid system will be followed for this tender. In this system bidder must submit their offer in separate sealed envelopes as – Technical Bid and Price Bid. Both the Technical Bid and Price Bid envelopes should be clearly marked as “Envelope No. 1 Technical Bid" and "Envelope No. 2 Price Bid" and both these sealed covers are to be put in a bigger cover which should also be sealed and duly superscribed with our Tender No. & Due Date and to be submitted to the concern department/section mentioned in tender document.
Opening Date & Time of tender 29th April 2016 at 3.00 pm
Place of Opening Tender Materials Management Division, IIT Bombay, Powai, Mumbai 400 076.
Tender Fees Tender Fee of Rs. 500/ (Rs. Five Hundred Only) in the form of Demand Draft in the favour of 'The Registrar, IIT Bombay' payable at Mumbai' to be submitted in Technical Bid“Envelop 1”.
Earnest Money Deposit Earnest Money Deposit (EMD) of Rs. 5,00,000/ (Rs. Five Lakh Only) in the form of Demand Draft in the favour of 'The Registrar, IIT Bombay' payable at Mumbai to be submitted in Technical Bid
MMD, IIT BOMBAY Page no. 3 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
“Envelop 1”.
Any Clarification Name : Deputy Registrar Dept : Materials Management Division ,IIT BombayEmail : [email protected] No. : 0222576 8805/8800
MMD, IIT BOMBAY Page no. 4 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
SECTION 2 (A) ELIGIBILITY CRITERIA FOR OFFICE FURNITURE
1. The Bidder should have existence of firm for a minimum period of ten years – (Certificate of Incorporation/Registration Certificate of the firms)(Copy to be enclosed).
2. Copy of the PAN CARD of the firm. (Copy to be enclosed).3. The Bidder must not be blacklisted/Suspended or any service related dispute with any
organisation/Govt. Organisations/Semi Govt org/ Banks in India or out side India. Annexure 2.4. The Bidder should accept RFP Terms & Conditions Annexure 3.5. Client's Experience Details Annexure 4. Work completion certificate from any government
organisation of single purchase order for supplies of furniture worth Rs 2 crore during last five years. – (work completion certificate to be enclosed and details in Annexure 4)
6. The Bidder should have Excisable Annual Business Turnover of minimum 4 Crores for the last two Financial years i.e. 201314 & 201415. Annexure 5 (Enclosed copy of Excise Duty paid challan). In absence of Excise duty paid challan for four crores turnover for last two years, tender will be rejected. This is to ensure that the bidder is Original Manufacturer. Sales Turnover will not be considered for eligibility. (Copy of Audited Annual Accounts for the last two years to be submitted).
7. The Bidder should have submitted filed ITR for last two years i.e. A.Y. 201415 & A.Y. 201516. Annexure5. (Copy of filed Acknowledgments to be submitted.)
8. Bidder's Information. Annexure6.9. Valid Sales Tax/VAT Registration certificate. (copy to be enclosed)10. Factory ACT Registration Certificate. (copy to be enclosed)11. EPF/ESIC Registration Certificate. (copy to be enclosed)12. The furniture manufacturing companies should possess prevalent certification related to quality
& safety possessed by most of reputed brands of furniture manufacturers e.g. ISO9001, ISO 14001, ISO18001, BIFMA (Certificates to be attached).
13. The bidder should possess 10 tank Anti Rust treatment plant, powder coating machinery and oven in their own premises to ensure minimum BGrade phospating and quality power coating. (copy of detail machinery to be attached).
14. Most of the furniture should be in Knock down Design.
MMD, IIT BOMBAY Page no. 5 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
(B)ELIGIBILITY CRITERIA FOR MODULAR /CUSTOMISED FURNITURE
1. The Bidder should have existence of firm for a minimum period of ten years – (Certificate of Incorporation/Registration Certificate of the firms)(Copy to be enclosed).
2. Copy of the PAN CARD of the firm. (Copy to be enclosed).3. The Bidder must not be blacklisted/Suspended or any service related dispute with any
organisation/Govt. Organisations/Semi Govt org/ Banks in India or out side India. Annexure 2.4. The Bidder should accept RFP Terms & Conditions Annexure 3.5. Client's Experience Details Annexure 4. Work completion certificate from any government
organisation of single purchase order for supplies of furniture worth Rs 2 crore during last five years. – (work completion certificate to be enclosed and details in Annexure 4)
6. The Bidder should have Excisable Annual Business Turnover of minimum 4 Crores for the last two Financial years i.e. 201314 & 201415. Annexure 5 (Enclosed copy of Excise Duty paid challan). In absence of Excise duty paid challan for four crores turnover for last two years, tender will be rejected. This is to ensure that the bidder is Original Manufacturer. Sales Turnover will not be considered for eligibility. (Copy of Audited Annual Accounts for the last two years to be submitted).
7. The Bidder should have submitted filed ITR for last two years i.e. A.Y. 201415 & A.Y. 201516. Annexure5. (Copy of filed Acknowledgments to be submitted.)
8. Bidder's Information. Annexure6.9. Valid Sales Tax/VAT Registration certificate. (copy to be enclosed)10. Factory ACT Registration Certificate. (copy to be enclosed)11. EPF/ESIC Registration Certificate. (copy to be enclosed)12. The furniture manufacturing companies should possess prevalent certification related to
quality & safety possessed by most of reputed brands of furniture manufacturers e.g. ISO9001, ISO 14001, ISO18001, BIFMA (Certificates to be attached).
13. The bidder should possess 10 tank Anti Rust treatment plant, powder coating machinery and oven in their own premises to ensure minimum BGrade phospating and quality power coating. (copy of detail machinery to be attached).
14. Most of the furniture should be in Knock down Design.
MMD, IIT BOMBAY Page no. 6 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
(C) ELIGIBILITY CRITERIA FOR LAB FURNITURE / FUME HOOD
1. The Bidder should have existence of firm for a minimum period of ten years – (Certificate of Incorporation/Registration Certificate of the firms) (Copy to be enclosed).
2. Copy of the PAN CARD of the firm. (Copy to be enclosed).3. The Bidder must not be blacklisted/Suspended or any service related dispute with any
organisation/Govt. Organisations/Semi Govt org/ Banks in India or out side India. Annexure 2.4. The Bidder should accept RFP Terms & Conditions Annexure 3.5. Client's Experience Details – Work completion certificate from any government organisation of
single purchase order for supplies of furniture worth Rs. 1 crore during last five years.(work completion certificate to be enclosed and details in Annexure 4)
6. The Bidder should have Annual financial Turnover of Rs. 20 Crores on manufacturing, supply & installation of lab furniture works for the last two Financial years i.e. 201314 & 201415.(Copy of Audited Annual Accounts for the last two years to be submitted). Annexure 5
7. The Bidder should have submitted filed ITR for last two years i.e. A.Y. 201415 & A.Y. 201516. Annexure5. (Copy of filed Acknowledgments to be submitted.)
8. Bidder's Information. Annexure6.9. Valid Sales Tax/VAT Registration certificate. (copy to be enclosed)10. Factory ACT Registration Certificate. (copy to be enclosed)11. EPF/ESIC Registration Certificate. (copy to be enclosed)12. Lab furniture comprising of fume hoods, lab work benches, electrical, LAN, gas & utility
distribution, etc. 13.The bidder should have in house ASHRAE ( American Society of Heating, Refrigerating, and
AirConditioning Engineers) 110: 1995 and EN 14175:2003 fume hood test facility. Photographs of this test facility must be attached to the technical bid. (Certificates to be enclosed).
14.SEFA ( Scientific Equipment and Furniture Association) Membership Certificates for Last four years on a continuous basis. (Certificates to be enclosed).
15.Test Report: Welded Cabinets should be thirdparty tested for SEFA (Scientific Equipment and Furniture Association) 8M by an independent thirdparty . (Certificates to be enclosed).
16.Test Report: Lab Furniture should be thirdparty tested for DIN EN 13150 (Workbenches for laboratories – Safety requirements and test methods : English Version of DIN EN ). (Certificates to be enclosed).
17.Test Report: Lab Furniture should be thirdparty tested for SEFA 8(Scientific Equipment and Furniture Association). (Copy to be enclosed).
18.Test Report: Welded Cabinets should be thirdparty tested for DIN EN 14727 (Workbenches for laboratories – Safety requirements and test methods : English Version of DIN EN ). (Certificates to be enclosed).
19.Test Report: Fume Hood should be typetested as per EN 14175 by a thirdparty . (Certificates to be enclosed).
20.Test Report: Fume Hood should be typetested as per ASHRAE ( American Society of Heating, Refrigerating, and AirConditioning Engineers) 110 by a thirdparty. (Certificates to be
MMD, IIT BOMBAY Page no. 7 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
enclosed).21. Membership Certificate: The bidder/parent company should possess the key professional staff,
at least one, in his organization with good knowledge of codes and standards like SEFA (Scientific Equipment and Furniture Association), OSHA (Occupational Health and Safety Management System), EN 14175, ASHRAE ( American Society of Heating, Refrigerating, and AirConditioning Engineers) 110 and NFPA 45. Such professionals should have a valid membership of SEFA (Scientific Equipment and Furniture Association) and in addition membership of any of the international governing standards ISO 90012008, ISO 140012004, BS OSHAS (Occupational Health and Safety Management System) 180012007 (For Design, Development, Manufacturing, Supply and servicing), (Certificates to be attached.)
22. The steel laboratory furniture manufacturer shall provide work tops and casework all manufactured & shipped with proper packing.
23. General Performance: Furniture shall meet the performance requirements and should follow SEFA (Scientific Equipment and Furniture Association) 8 guidelines
24. The dealer/the company should have own manpower for all design & execution related works stationed.
25. The bidder should possess 9 tank Anti Rust treatment plant, powder coating machinery and oven in their own premises to ensure minimum BGrade phospating and quality power coating. (copy of detail machinery to be attached).
MMD, IIT BOMBAY Page no. 8 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
SECTION 3 – INSTRUCTIONS TO BIDDERS
Submission of Offer: • Tender MUST BE ENCLOSED IN A SEALED COVER superscribing Tender number / due date &
should reach the undersigned on or before due date mentioned in the tender notice. If the quotation cover is not sealed, it will be rejected.
• Tender should be dropped in the tender box kept in the office of concerned Department / Section or to Indenter. No tender is to be handed over to our staff personally unless otherwise specified. All communications are to be addressed to the undersigned only. In case due date happens to be holiday the tender will be accepted and opened on the next working day.
• Tender can be submitted in person or through post/ courier (IIT Bombay shall not be responsible for any postal delays or any other reason for not submitting the bid in the specified time and resulting in disqualification / rejection of any bid) so as to reach on or before the due date and time.
• Any information furnished by the bidder found to be incorrect either immediately or at a later date, would render him liable to be debarred from tendering/taking up of work in IIT Bombay.
Cost of Bidding
• The Bidder shall bear all costs associated with the preparation and submission of its Bid and the Purchaser shall not be responsible or liable for those costs regardless of the conduct or outcome of the bidding process.
Amendment of Bidding Documents
• At any time prior to the deadline for submission of bids,IIT Bombay may, for any reason, whether on its own initiative or in response to the clarification request by a prospective BIDDER may modify the bid document.
• All prospective BIDDERs who have downloaded the bidding document may visit IIT Bombay, website for amendments / modifications which will be binding on them.
Bid Opening Process:
• The Technical Bid will be opened in the first instance in the presence of representatives of the bidders at IIT Bombay.
• Financial bids of only those bidders, whose bids are found technically qualified, by the Technical Evaluation Committee, will be opened in the presence of the vendor’s representatives subsequently at a later date for further evaluation.
• One authorized representative of each of the bidder would be permitted to be present at the time of aforementioned opening of the bids.
• The authorized representative of bidders, present at the time of opening of the bids shall be required to sign an attendance register as a proof of having attended the Price bid opening.
MMD, IIT BOMBAY Page no. 9 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Cancellation of tender: • Not withstanding anything specified in this tender document, Purchaser / IIT Bombay in
his sole discretion, unconditionally and without having to assigned any reasons, reserves the rights: a) To accept OR reject lowest tender or any other tender or all the tenders. b) To accept any tender in full or in part. c) To reject the tender offer not confirming to the tenders terms. d) To give purchase preference to Public Sector undertakings when applicable as per Govt. Policy/ Guidelines.
• The conditional bid will be summarily rejected.
Late tenders : IIT Bombay will not be responsible:
i) For delayed / late tender submitted / sent by post / courier etc. ii) For submission / delivery of quotations at wrong places other than the mentioned in the tender.iii) Fax / Email / Telegraphic / Telex tenders will not be considered. iv) Any bid inadvertently received by IIT Bombay after the deadline i.e. due date & time for submission of bids, will not be accepted and returned unopened to the BIDDER.
Validity of the offer :
180 Days from the date of opening of the Technical bid .
Transfer and subletting :
The seller shall not sublet, transfer, assign or otherwise part with the acceptance to the tender or any part thereof, either directly or indirectly, without the prior written permission of the Purchaser.
Evaluation of Offer :
• After preliminary scrutiny of the firms; the firms satisfying eligibility criteria will be called for presentation to the Institute and the committee may visit factory of all the prequalified bidders.
• The successful bidders will have to submit samples if the committee requires and the cost for transportation will have to beared by the bidders.
Deadline for Submission of Bids :• Bids must be received by IIT Bombay before the due date and time at the address specified in the
tender document. In the event of the specified date for the submission of bids being declared as a holiday for IIT Bombay the bid-closing deadline will stand extended to the next working day up to the same time.
MMD, IIT BOMBAY Page no. 10 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Earnest Money Deposit :While submitting bid, the BIDDER shall deposit an amount mentioned in tender document as Earnest Money, with the IIT Bombay through the following instruments:
1. Earnest Money Deposit (EMD) of Rs. 5,00,000/ (Rs. Five Lakh Only) in the form of Demand Draft in the favour of 'The Registrar, IIT Bombay' payable at Mumbai to be submitted in Technical Bid. Failing which, submitted bid will be Rejected.
2. The Earnest Money shall be valid upto a period of 180 days .3. No interest shall be payable by the BUYER to the BIDDER on Earnest Money for the period of
its currency. 4. EMD of a tenderer will be forfeited, if the tenderer withdraws or amends its tender or
derogates from the tender in any respect within the period of validity of its tender. Further, if the successful tenderer fails to furnish the required performance security within the specified period, its EMD will be forfeited.
MMD, IIT BOMBAY Page no. 11 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
SECTION 4 : TERMS & CONDITIONS OF CONTRACT
Award of Contract• The Empanelment and Rate Contract will be valid for a period of ONE year.• For all categories L2 will be allowed to match with L1 and both will be empaneled for that
particular item.• Purchase Orders will be placed from various department/sections and centers with reference to
the contract.• The Company should have technically qualified manpower available and first response time for
service should be within two working days (excluding Sunday / holiday).• The firm under the contract will have sole responsibility of providing furniture layout
drawings/design of furniture to the Institute without any extra cost for the period of contract. • The Rate contract will be terminated, if the firm fails to abide by the terms and conditions of the
contract or fail to supply the goods in time or supply substandard goods or make any false declaration or fails to provide satisfactory after sale service to the Institute. In such situation the penalty will be imposed on the firms by an expert committee and penalty amount will be deducted from the Security Deposits provided by the firm.
• IIT Bombay reserves right to keep number of firms in Rate contract for the supply of furniture & fixture.
• If the quality of product and service provided is not found satisfactory, IIT Bombay reserves the right to cancel or amend the contract.
• The Empaneled supplier will be abide by all the Terms & Conditions of the Tender.• Warranty for all the products quoted to be given 3 Years.• Deviation+ / 5% is acceptable. • Manufacturing Testing Certificate will be required to be submitted for all the products. • Samples have to be submitted for approval before supply of material and cost of approved
samples will be paid. • IIT Bombay reserves the right to cancel any category from the rate contract and continue with
other categories.
Prices
• Bid Prices MUST BE SUBMITTED IN ENCLOSED PRICE BID FORM ONLY.• If the price is not quoted in Price Bid Form provided in tender document then, IIT Bombay will
reject bid along with forfeiting Earnest Money Deposit. If supplier wish to give pricing details may be attached in separate sheet.
• As per Govt. of India Notification no. 10/97CE dt. 1st March 1997, IIT Bombay is exempted from Excise duty for SCIENTIFIC / TECHNICAL INSTRUMENTS WHICH ARE USED FOR RESEARCH PURPOSE ONLY. If the items are exempted under notification NO. 10/97CE dt. 1st March 1997 certificate will be provided. We shall provide all the documents under this notification to enable you to clear the goods without payment of excise duty, whenever required. Please state clearly that this certificate is required.
• Any new taxes and duties liable on the subject contract due to change in legislation during the contract period shall be reimbursed subject to the applicability of the said act to the satisfaction of
MMD, IIT BOMBAY Page no. 12 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
the purchaser and the production of documentary evidence after availing of statutory concession, benefits etc.
• The supplier shall pay and bear all other liabilities, taxes and duties not specifically agreed by the Purchaser in the contract.
• VAT/Other Govt. Taxes : Excise Duty (ED), other taxes, levies, like Service Tax (ST), Education Cess, etc., are to be indicated separately. BIDDER should mention Central and State Sales Tax/VAT Registration, PAN Number are to be necessarily indicated in the offer.
• We are not authorised to issue any Sales Tax forms like form “C” & “D”.
Terms of payment : • Payment within 30 days from the date of delivery and & Acceptance Certificate of concerned
Department / Section / Materials Management Division. Advance payment will be made against Bank Guarantee.
• Payment shall be made by Cheque or such other mode / electronic fund transfer offered by the Bank.
Delivery schedule :• Free delivery at IIT Bombay. General Delivery Period is 2-4 weeks, and for bulk purchases
delivery period is 6-8 weeks from the date of issue of Purchase order. Non-availability of the stock should be informed in writing immediately. No part-supply will be allowed. Defective items or items not as per given brands or samples, if any supplied must be taken back and be replaced with no additional cost.
Security Deposit :• For successful tenderer/ bidder Earnest money deposit will be converted to Security Deposit and
will be retained with IIT Bombay till the expiry / termination of rate contract without interest.• The successful tenderer is entirely responsible for due performance of the contract in all respects
according to the speed, intent and meaning of the terms and conditions and specification and all other documents referred to in the acceptance of tender.
Penalty :• Timely delivery is essence of the contract and hence if any consignment be delayed,liquidated
damages at the rate 0.5% of the price of the delayed consignment, for each week or part whereof shall be levied and recovered subject to maximum of 5% of total purchase order value.
Force Majeure : • Force Majeure will be accepted on adequate proof thereof.
Legal matter : • In the event of any dispute over this contract, IIT Bombay's decision shall be final and binding.
MMD, IIT BOMBAY Page no. 13 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
SECTION 5 : ANNEXURES
ANNEXURE 1 UNDERTAKING FOR SUBMISSION OF OFFER(On Company / firm's Letterhead)
To, Date: The Deputy RegistrarMaterials Management DivisionI.I.T. Bombay,Powai, Mumbai – 400 076.
Dear Sir,
Sub: RFP No. MMD/Furniture& Fixtures/RC/201617 dated 16th February, 2016 for “RFP for Empanelment & Annual Rate contract of suppliers for Furniture & Fixtures”.
I/we hereby confirm that we are interested in following categories of Furniture & Fixtures and has submitted the documents for the same :
Sr. No. Type of Furniture & Fixtures category Submit quotation for (Yes/No)
A. Office furniture
B. Modular / Customised furniture
C. Lab Furniture/ Fume Hoods
I hereby declare that information submitted by us in this tender is best of our knowledge and its true. If you found any discrepancies in the tender information you can disqualify my tender without notice.
Yours faithfully,
(Signature of the Bidder)Printed NameDesignationSealDate :Business Address :
MMD, IIT BOMBAY Page no. 14 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
ANNEXURE 2 – DECLARATION REGARDING CLEAN TRACK (On Company / firm's Letterhead)
To, Date :
The Deputy RegistrarMaterials Management DivisionI.I.T. Bombay,Powai, Mumbai – 400 076.
Sir,
Re: RFP No. MMD/Furniture& Fixtures/RC/201617 dated 16th February, 2016 for “RFP for Empanelment & Annual Rate contract of suppliers for Furniture & Fixtures”.
I/we carefully gone through the Terms & Conditions contained in the above referred RFP. I/we hereby declare that my company / firm is not currently debarred / black listed/convicted by any Government / Semi Government Organizations / Institutions in India or abroad. I/we further certify that I'm competent officer in my company /firm to make this declaration.
Or
I/we declare the following
No.
Country in which the company is debarred / blacklisted / case is pending
Black listed / debarred by Government / Semi Government Organizations / Institutions
ReasonSince when and for how long
(NOTE : In case the company / firm was blacklisted previously, please provide the details regarding Period for which the company / firm was blacklisted and the reason/s for the same)
Yours faithfully
(Signature of the bidder)
Printed NameDesignation
MMD, IIT BOMBAY Page no. 15 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
ANNEXURE 3 : DECLARATION FOR ACCEPTANCE OF RFP TERMS AND CONDITIONS(On Company / firm's Letterhead)
To, Date :The Deputy RegistrarMaterials Management DivisionI.I.T. Bombay,Powai, Mumbai – 400 076.
Sir,
Re: RFP No. MMD/Furniture& Fixtures/RC/201617 dated 16th February, 2016 for “RFP for Empanelment & Annual Rate contract of suppliers for Furniture & Fixtures”.
I/we carefully gone through the Terms & Conditions as mentioned in the above referred RFP document. I/we declare that all the provisions of this RFP are acceptable to my company. I /we further certify that I'm an authorized signatory of my company and am, therefore, competent to make this declaration.
Yours faithfully,
(Signature of the bidder)Printed NameDesignationSeal
Date :Business Address :
MMD, IIT BOMBAY Page no. 16 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
ANNEXURE 4 : CLIENT EXPERIENCE DETAILS(On Company / firm's Letterhead)
To, Date :The Deputy RegistrarMaterials Management DivisionI.I.T. Bombay,Powai, Mumbai – 400 076.
Sir,Re: RFP No. MMD/Furniture& Fixtures/RC/201617 dated 16th February, 2016 for “RFP for
Empanelment & Annual Rate contract of suppliers for Furniture & Fixtures”.
Brief particulars of the similar work done in government institutions: (Please attach copy of work orders for our reference) :Order Placed by (full add of client)
Order No. & date
Item Description Value of order
Date of completion of contract
Contact Person along with Telephone No., Fax No. and email address.
Yours faithfully,
(Signature of the bidder)Printed NameDesignationSealDate : Business Address :Encl : As above
MMD, IIT BOMBAY Page no. 17 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
ANNEXURE 5 : DECLARATION OF ANNUAL TURNOVER AND INCOME TAX RETURN (On Company / firm's Letterhead)
To, Date: The Deputy RegistrarMaterials Management DivisionI.I.T. Bombay,Powai, Mumbai – 400 076.
Sir,
Re: RFP No. MMD/Furniture& Fixtures/RC/201617 dated 16th February, 2016 for “RFP for Empanelment & Annual Rate contract of suppliers for Furniture & Fixtures”.
1) I/we hereby declare that, our firm's Annual Turnover as follows, and I/we have also supported an Audited Accounts for your references :
F. Y. 2013 – 14 F. Y. 2014 – 15
And,
2) I/we hereby declare that, our firm had filed Income Tax Returns for last years i.e. A.Y. 201415 & A.Y. 201516. Supported by copy of ITR of two years.
Yours faithfully,
(Signature of the bidder)Printed NameDesignationSeal
Date :Business Address :
Encl : As above
MMD, IIT BOMBAY Page no. 18 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
ANNEXURE 6 : BIDDER'S INFORMATION (On Company / firm's Letterhead)
Details of the bidders :
1 Name of the bidder
2 Address of the bidder
3 Status of the Company (Public Ltd./ Pvt. Ltd.)
4 Details of the Incorporation of the Company Date:
Ref. Document
5 Valid Sales Tax Registration No.
6 Valid Service Tax Registration No.
7 Permanent Account No. (PAN)
8 Name & Designation of the Contact person to whom all references shall be made regarding this tender.
9 Telephone No. (with STD Code)
10 Email Address of the contact person
11 Fax No. (with STD Code)
MMD, IIT BOMBAY Page no. 19 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
SECTION 6
(A) Technical Bid : Office Furniture
The vendors must provide the following mandatory information :
Sr. No.
Type Particulars with details specification Sample Image Complian
ce(Yes /
No)
If any
Deviation
mention
1 Office Chair (1)
The seat and back are made from 1.2_+ 0.1cm thick hot pressed plywood and upholstered with fabric and moulded polyurethanefoam together with seat and back covers. The back foam is designed with contoured Lumbar support for extra comfort. The Lowback SIZE: 44.0cm (W) *47.0cm. (H), SEAT SIZE: 52.0(W)*48.0CM.(D) Overall Dimensions: 70.0 cm(W)*70.0 cm(D)*87.5cm(H)-98.5cm, Seat Height:43.0Cm -54.0 Cm The polyurethane foam is moulded with density=45+/-2kg/m3 and hardness load 16_+2Kgf for 25% compression. The seat and back covers are injection moulded in black Co-polyner Polypropylene. The one-piece armrest are made of black integral skin polyurethane reinforced with M.S insert with 50-70 Shore 'A' hardness.The armrests are scratch and weather resistant.The armrests are fitted to the seat with armrest brackets made of 0.5_+0.5cm thk.HR . The permanent contact mechanism is designed with the following features: 360 degree revolving type, 14 degree _+ 2 degree maximum back tilt only, Upright position locking, Tilt tension adjustment. The Pneumatic height adjustment has an adjustment styroke of 9.0 _+ 0.3cm. The below is 3 piece telescopic type and injection moulded in
MMD, IIT BOMBAY Page no. 20 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification Sample Image Complian
ce(Yes /
No)
If any
Deviation
mention
black polypropylene. The pedestal is fabricated from 0.2_+0.2cm Thick HR sheet(IS:DD 1079/HR),POWDER COATED (DFT 40-60 MICRONS) AND FITTED WITH AN INJECTION MOULDED black polypropylene hub cap and 5 nos.twin wheel castors, The pedestal is 60.0_+0.5cm. Pitch-centre dia (70_+1.0 cm with castors).The twin wheel castors are injection moulded in Black Nylon.
2 Office Chair (2)
Medium Back Revolving Chair Upholstry/Frame: 12 mm hot pressed ply covered with moulded Polyurethene foam in seat with Polypropylenecover & back with ABS cover upholstered with fabric Seat size : 500 mm (W) x 460 mm (D)Back size : 500 mm (W) x 600 mm (H)Arms: Steel inserted Polyurethene arms fixed with seat Standard Mechanism : Synchro tilt Single point Mechanism Height Adjustment : Gas Lift Base : Nylon base with twin wheel castors
MMD, IIT BOMBAY Page no. 21 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification Sample Image Complian
ce(Yes /
No)
If any
Deviation
mention
3 Office Chair (3)
1. SEAT/BACK ASSEMBLY: The seat is uphol made up of 12 MM thick hot pressed plywood HB2 stered with Mesh fabric and Polyurethane Foam. The back is made up High quality Nylon mesh. The back is made of stretched Mesh designed to provide maximum lumber support for comfortable seating posture. a. Chair Dimensions Max Height = 1130mm Chair Depth = 710mm Upholstery Used = Fabric + Mesh b. Base Seat Width = 470mm Depth / Length = 620mm Thickness = 50mm c. Back Seat Width = 480mm Length = 480mm Thickness = 13mm d. Min. Seat Height from Ground = 650mm 2.POLYURETHANE FOAM: The polyurethane foam for seat is moulded with density = 45 +/ 2 kg/m3 and Hardness = 20 +/ 2 kg/m3.3. ARMRESTS: Adjustable PU Type Arm. Adjustable PU Type ARM Handle Out = 630mm Adjustable PU Type ARM Handle In = 460mm 4. Centre Syncro MECHANISM: The mechanism is designed with the following features: • Seat pan and backrest is linked so that the angles adjust in a fixed ratio. The backrest tilts 1.5 2.5 degrees for each degree of seat pan til. 5. PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height has an adjustment of 120 MM. 6. PEDESTAL ASSEMBLY: The pedestal is fabricated from plastic compound with steel inserted injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 610 ±8 MM. Pitch center dia. (710±10 MM with castors). 7. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon.
MMD, IIT BOMBAY Page no. 22 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification Sample Image Complian
ce(Yes /
No)
If any
Deviation
mention
(Castor wheel dia. 5.0 cm) 8. Fabric Color Available = Maroon, Red, Orange, Dark Blue, Sky Blue, Green, Grey, Black 9. Mesh Color Available = Black
4 Executive Chair (1)
The seat is made up of insert moulded Polyurethene Foam upholstered with foam laminated mesh fabric. The insert moulded foam is assembled over a load bearing plastic seat cover. Back is made up of two piece injection moulded frame and has adjustable lumbar support for achieving comfortable seating.The Polyurethene foam for seat is moulded with density 65+5kg/m3. Overall Dimension: 76cm(W)*76cm(D)*117cm(H)132cm and seat height 45cm54cm.Seat size 51cm(W)X52.5cm.The armrest top is injection moulded in polyurethane and mounted on injection moulded height adjustable type armrest. The armrest height is adjustable up to 4.5+_0.5cm in 3 steps width adjustable up to 20mm. The mechanism shall be designed with 360° revolving type, The mechanism shall be single point control. Front pivot for tiltwith feet resting on ground ensuring more comfort. Tilt tension adjustment. 4position locking with antishock feature. Spine bracket is made up of Aluyminium Diecast piece. The neck trest assembly is mounted on top of back.It can be adjustable to 4.5+_0.5cm up and down. Pneumatic height adjustment has an adjustment of 9.0+_0.3cm. Pedestal is made of Die cast aluminium fitted with 5 nos twin wheel casters. Twin wheel castor having are injection moulded in black nylon.
MMD, IIT BOMBAY Page no. 23 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification Sample Image Complian
ce(Yes /
No)
If any
Deviation
mention
5 Executive Chair (2)
The cushioned seat assembly consist of seat outer(material30% Glass Fiber Nylon) & upholstered Seat inner (material Poly Propylene) with moulded Polyurethene foam & polyster fabric.The Net Back is made up of Back outer (material Glass Fiber Filled Nylon) & Back inner (materialPP) and upholstered using Polyster Mesh fabric with high tenacity yam. It has full back size of 46.5cm (W) and 60.0cm (H). It has a seat size of 51.0cm (W) X 49.0cm(D).Overall Dimension: 75.0 CM X 75.0 CM X 109.3124.4 CM;Seat Height : 45.5Cm X 55.5 cm .The HR Polyurethane foam is moulded with density=45±2 kg/m^3 and Hardness load 12± 2 kgf for 25% compression. The support spine is made up of High Pressure Die cast polished Aluminium. The armrest having two adjustment , Height(6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment is provided in aluminium structure of armrest which is connected to Aluminium Back spine and is operated by button.The depth adjustment is provided in pad which is fixed to armrest structure.The mechanism shall be designed with 360° revolving type, Uprightposition locking, The mechanism shall be single point control. Front pivot for tilt with feet resting on ground ensuring more comfort. Tilt tension adjustment, Seat/back tilting ratio of 1:2. Seat depth adjustment range is of 3.75+0.1cm . Lumber support assembly consist of lumbar spine (material Glass Fiber Filled Nylon) which is fixed to aluminium Back spine. Lumbar support Assembly has height adjustment of 5.0±0.5cm. The Neckrest assembly consists of upholstered Neckrest inner (material Poly Propylene) with moulded Polyurethane foam &
MMD, IIT BOMBAY Page no. 24 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification Sample Image Complian
ce(Yes /
No)
If any
Deviation
mention
polyester fabric. Neck rest assembly has height adjustment of 5.5±0.5cm and Rotation adjustment of overall 20 degree. The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm.The pedestal is High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitchcenter dia.The twin wheel castors are injection moulded in black PP having 6.0±0.1cm wheel Diameter.
6 Executive Visitor Chair without wheels
The seat is made up of 1.2+_0.1 cm. thick hot pressed plywood upholstered with leatherite and moulded Polyurethane Foam. The back is made up 1.2 cm +0.1cm. thick hot pressed plywood upholstered with replaceable leatherite upholstery covers and moulded polyurethane foam.The back ply and foam is designed with contoured lumber support for comfortable seating posture.MID BACK SIZE 48.0cm.(W) X 64.5cm.(H)SEAT SIZE 51.0cm.(W) X 48.0cm.(D)Overall Dimension : 66.5 cm (W)X 58.0 cm(D) X 88.5 cm (H)The polyurethane foam for seat and back is moulded with density = 45plus minus2 kg/m3 and Hardness = 20 plus minus 2.The armrest top is made of moulded polyurethane (P.U) and mounted on to a fixed type M.S. tubular armrest support chrome plated.The backrest consists of a fixed type mechanism i.e no back up/down adjustment.Leg frame welded assembly made from 35 X 15 X 16BG (1.6THK) Elliptical M.S ERW tube with base plate chrome plated for seat fixing.
MMD, IIT BOMBAY Page no. 25 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification Sample Image Complian
ce(Yes /
No)
If any
Deviation
mention
7 Visitor Chair
Seat Back Assembly – The seat and back are made up of 1.2 +_0.1 cm,thick hot pressed plywood measured and upholstered with fabric upholstery cover and moulded polyurethanefoam.The back foam is designed with contoured lumber support for extra support.The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE 47.5 cm. (W) * 58.0 cm (H) and SEAT SIZE47.0cm(W)*48.0cm(D). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +_ 2 Kg/m3 and hardness load of 16_+2 Kgf as per IS:7888 for 25% compression. ARMRESTS: The onepiece armrest are injection moulded from black Co polymer Polypropylene. CENTER TILT STNCRO MECHANISM : The mechanism is designed with the following feature. 360 degree revoling type. Upright position locking Tilf tension adjustment Seat/back tilting ratio of 1:3 PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0_+0.3cm. TELESCOPIC BELLOW ASSEMBLY : The bellow is 3 piece telescopic type and injection moulded in black polypropylene. PEDESTAL ASSEMBLY : The pedestal is injection moulded in black 33% glass filled Nylon66 and fitted with 5 nos twin wheel castors, The pedestal is 66.3_+0.5cm. Pitch center dia(76.3_+1.0cm with castors) TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in black nylon.
MMD, IIT BOMBAY Page no. 26 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification Sample Image Complian
ce(Yes /
No)
If any
Deviation
mention
8 Visitor Chair Without Wheels
The seat / back are made up of 1.2 ±0.1cm. thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam together with moulded seat and back covers. The back foam is designed with contoured lumbar support for extra comfort.* MID BACK SIZE 50.0 cm. (W) x 49.0 cm. (H) * SEAT SIZE 50.0 cm. (W) x 46.5 cm. (D)Overall Dimension: 59.0cm(W) X 63.0 cm(H)X81.5 cmThe Polyurethane foam is moulded with density = 45±2 kg/m3 and Hardness = 20±2 at 25% compression.SEAT BACK COVERS: For the seat and Back cover is injection moulded in black copolymer polypropylene. The onepiece armrests made of black integral skin polyurethane with 5070 Shore 'A Hardness and reinforced with M.S. insert. The armrests are scratch and weather resistant. The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 0.5 ± 0.05 cm. thk. HR steel.The tubular frame is cantilever type & made of 0 2.54 +0.03cm. x 0.2 ±0.016cm.thk M.S. E.R.W. tube and black powder coated ( DFT 4060 microns).
MMD, IIT BOMBAY Page no. 27 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification Sample Image Complian
ce(Yes /
No)
If any
Deviation
mention
9 Conference Chair
The seat is made up of 1.2 +/ 0.1 cm thick hot pressed plywood. The back is made up of injection moulded glass filled nylon & upholstered using Net fabric with high tenacity yarn. Seat Size 47cm (W) x 51.5(D) cm , Back Size 45cm X 65.3cm (H).The HR polyurethane foam shall be moulded with density= 45+/2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The armrest have an Up down adjustment of 8.5 +/ 0.5 cm which is provided in armrest structure. Armrest top has an integrated layer of Thermoplastic Elastomer. The lumbar suport consist of polpropylene pad wih moulded polyurethane foam & covered with polyster fabric. The height of lumbar pad can be adjusted through two projecting knobs provided on rear side of pad. The lumbar pad has an adjustment of 8.0 +/ 0.5 cm in height. The adjustable tilting mechanism with 360 degree revolving type, single point control, front pivot for tilt with fet resting on ground ensuring more comfort, tilt tension adjustment, 4 position locking with anti shock feature, seat/back tilting ratio of 1:2.The pedestal is injection moulded in black 30% glass filled Nylon and fitted with 5 nos twin wheel castors. The twin wheel castors are injection moulded in black Nylon.Overall Dimension:76.2cm(W)X 76.1cm(D)X 98.0108.0cm(H)
10 Study Chair(1)
The seat subassembly is made up of 1.2±0.1cm thk hot pressed Plywood & back in injection moulded from black copolymer polypropylene upholstered with fabric and moulded polyurethane foam together with seat and back covers.The back foam is designed with contoured lumber support for extra support.The seat and back cover is injection moulded in black copolymer polypropylene.BACK SIZE: 45.0 cm (W) X 42.0 cm (H);SEAT SIZE: 39.0cm (W) X 38.0 cm (D)Overall Dimension : 55.5cm (W) X 72.5cm (D) X 84.0 cm (H); Seat Height : 45.0 cmThe HR polyurethane foam shall be moulded with density= 45+/2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compressionThe tubular frame is made of 0 2.54 ±0.03cm. x 0.16 ±0.0128cm.thk. M.S. E.R.W. tube and black powder coated ( DFT 4060 microns ). The armrests are made of black integral skin Polyurethane with 5070 Shore 'A' Hardness and reinforced with M.S. insert. The P.U. armrests are then fixed to black powdercoated (DFT 4060 microns )
MMD, IIT BOMBAY Page no. 28 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification Sample Image Complian
ce(Yes /
No)
If any
Deviation
mention
armrest brackets made of of 0.8 ± 0.05 cm. thk. HR steel.The RH bracket has provision for mounting retractable desklet.The desklet is fixed retractable type & made up of 1.8 ± 0.05cm thick medium density fiberboard and membrene formed with black 0.4mm thick PVC film.The bottom side is provided with backing laminate.pprox Size of Desklet : 34.5± 0.1 cm (W) x 26.5± 0.1cm (D)
11Study Chair
(2)
The seat subassembly is made up of 1.2±0.1cm thk Plywood upholstered with moulded foam and polyester fabric and covered with an injectionmoulded polypropylene outer cover. The seat can tipup when not in use and this feature can be used while stacking the chairs horizontally The back subassembly is made up of injectionmoulded polypropylene inner upholstered with moulded foam and polyester fabric and covered with an injectionmoulded polypropylene outer cover. The contoured back with width extension at the bottom area is designed to give comfort to lower back. The back flexing features allows the back to tilt by 9c±2' to aid the user in adopting a comfortable reclining posture. Both these subassemblies are fixed to the tubular structure,BACK SIZE: 45.2cm (W) X 44.6cm (H);SEAT SIZE: 47.0cm (W) X 50.0cm (D)Overall Dimension :71.0cm (W) X 82.0cm (D) X 89.0 cm (H); Seat Height : 47.5 cmThe powdercoated 4 leg structure is made of 2.2 ±0.03cm dia x 0.25 ±0.02cm thk M.S. E.R.W. Tube front and rear leg welded along with connecting tube made of 1.9 ±0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube to form the tubular frame assembly. The legs are provided with injectionmoulded adopter
MMD, IIT BOMBAY Page no. 29 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification Sample Image Complian
ce(Yes /
No)
If any
Deviation
mention
bush in black Nylon and brakeloaded castors enabling easy maneuvering while not in use and stable sitting while in use_ The chairs can be stacked horizontally when not in use. Polyurethane foam is moulded with density = 70.0 ±8.0 kg/m3 and Hardness = 20 ±2 for Seat & 16 ±2 for back at 25% compression.The armrest structure is made up of 2.2 ±0.03crn dia x 0.25 ±0.02cm thk M.S. E R.W. Tube welded to the Tubular Frame structure and having a scratchresistant ABS Arm top.The Full Desklet assembly is Flipup type and is made up of extension tube of 1.9 ±0.02em dia x 0_2 ±0.016cm thk PAS. E.R.W. Tube and a support tube on L.H. side of 1.6 ±0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube on which an scratch resistant ABS desklet top is fixed and covered on bottom side with a bottom cover.The brakeloaded castors are assembled to the chair legs, to give a free movement for maneuvering the chair when not in use and it will brake the movement when load is applied (while in use) to give a stable feel. The twin wheelcastors are injection molded in black Polypropylene.
12 Hostel Chair (1)
The seat / back are made up of 1.0 ±0.1cm. thick water resistant, flat plywood and upholstered with P.U. foam fabric.*MID BACK SIZE 42.0 cm. (W) x 26.5 cm. (H) * SEAT SIZE 42.0 cm. (W) x 42.0 cm. (D)Overall Dimension: 54.0cm(W) X 71.5 cm(H)X78.5 cm; Seat size: 45.5 cmThe Polyurethane foam is moulded with density = 45±2 kg/m3 and Hardness = 16±2 kgf at 25% compression.The tubular frame is made of 0 2.54 +0.03cm. x 0.2 ±0.016cm.thk M.S. E.R.W. tube to form complete assembly which is powder coated ( DFT 4060 microns ).
MMD, IIT BOMBAY Page no. 30 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification Sample Image Complian
ce(Yes /
No)
If any
Deviation
mention
13 Hostel Chair (2)
The seat / back are made up of 1.2 ±0.1cm. thick water resistant, flat plywood and upholstered with fabric or synthetic leather and moulded polyurethene foam.The back foam is designed with contoured lumber support for extra comfort.. MID BACK SIZE 46.0 cm (W) x 47.0 cm (H) * SEAT SIZE 46.0 cm (W) x 46.0 cm (D)Overall Dimension: 54.0cm(W) X 71.5 cm(H)X78.5 cm; Seat size: 45.5 cmThe Polyurethane foam is moulded with density = 45±2 kg/m3 and Hardness = 16±2 kgf at 25% compression.The assembly is welded understructure made up of 3.5 +0.03cm X1.5+0.02cm X 0.16 ±0.0128cm.thk M.S. E.R.W. OBLONG tube and black powder coated ( DFT 4060 microns ).
14 Canteen Chair (1)
The seatback shall be made up of injection moulded high impact strength polypropylene polymer compound with indoor grade UV resistance.BACK SIZE: 52.5cm. (W) X 53.2cm. (H);SEAT SIZE: 51.6cm. (W) X 40.5cm. (D)Overall dimension 52.5mm(W)X55.8mm(D)X84.5mm (H); Seat Height: 45.0 CmThe powder coated welded tabular frame is made from Deg. 2.22±0.03 cm x 0.16± 0.0128 cm and 3.5 ±0.03 cm x0.15±0.03cmx 0.16±0.0128 cm M.S.E.R.W. tube. The Powder coated welded beam M.S. Structure is made from 5.08 ±0.03 cm x 5.08 ±0.03cmx 0.16± 0.0128 cm.The 0.315 ± 0.008 cm thk HR plate is welded to beam for fixing seat and back frame.The Powder coated welded leg M.S. Structure is made from 5.08 ±0.03 cm x 5.08 ±0.03cmx 0.16± 0.0128cm and 5.08 ±0.03 cm x 2.45 ±0.03cm x 0.16± 0.0128cm.The shoes are made from high impact strength polyprolene polymer compound with indoor grade UV resistance and pressed fitted with tubular frame.
MMD, IIT BOMBAY Page no. 31 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification Sample Image Complian
ce(Yes /
No)
If any
Deviation
mention
15 Canteen Chair (2)
The seatback shell shall be made up of 1.2 ±0.1cm. thick hot pressed plywood and laminated with natural veneer in three different shades of Teak & Mahogany.* BACK SIZE: 42.0cm. (W) X 45.0cm. (H)* SEAT SIZE: 44.0cm. (W) X 40.0cm. (D)Overall dimension 51.5cm(W)X54.0cm(D)X86.0cm (H);Seat Height : 45.5 cmThe understructure is made of M.S. tube 0 1.9 ±0.02cm. x 0.16 ±0.0128cm. thk. and black powder coated ( DFT 4060 microns ).
MMD, IIT BOMBAY Page no. 32 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
FACULTY FURNITURE Compl
iance(
Yes /
No)
If any
Deviation
mention
16 Faculty Unit (1)
These Laminated top desks have a designer perforated modesty panel in mild steel. Comprising a desk unit, credenza and a free standing pedestal. Laminated Top : 36 mm thick laminated top* with 2mm lipping all around.36 mm top = 18 mm PLT + 18 mm PLB Baton. Understructure : MS frame of Rec. tube 40X20X1.6THK with CRMS 3thk plates for bolting the leg. Legs: MS ERW round tube of Dia 50 X 1.6 mm thick. Modesty & Side Panel : Perforated MS Sheet of 0.9 mm thick. Joining Plates CRMS 3thk plates to join Main desk with Extended Return Unit. Laminated Top: 36 mm thick laminated top with 2mm lipping all around. 36 mm top = 18 mm PLT + 18 mm PLB Baton. Pedestal : Shell : 0.8 mm Thick, Drawer Trey : 0.6 mm Thick, Drawer Front: 0.8 mm Thick, Sides: Double extension ball sides.Glass door unit: Body: 0.8mm Thick MS, Glass: 0.6mm Thick clear glass.
Main Desk1 Size(mms): 1500W x
800D x 750H
Type no.(16A)
Main Desk2 Size(mms):1800W x
800D x 750HType no.(16B)
Main Desk3 Size(mms): 2400W x
800D x 750HType No. (16C)
Free standing pedestal(cms)
Size:390 (w) X 590 (D)X646(h)
Type no.(16D) Extended Return Unit1 Size(cms): 1200W x 600D x
750HType no.(16E)
Extended Return Unit2
Size(cms):1675W x 600D x 750H
Type no.(16F)Extended Return
Unit3 Size: 900 x 450 x 750x 750
Type no.(16G)
(Side Table)Type no.(16H) Extended Return
Unit3 Size(cms):900W x
600D x 750HType no.(16I)
MMD, IIT BOMBAY Page no. 33 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Pedestal for Side Table (cms)
Size:390W x 435D x 674H
Type no.(16J)
Side Table 1 Size(mms): 1188 x
441 x 750Type no.(16K)
Side Table 2 Size(mms): 1188 x
441 x 750Type no.(16L)
Side Table 3 Size(mms): 1581 x
441 x 750Type no.(16M)
Side Table 4 Size(mms): 1581 x
441 x 750Type no.(16N)
Side Table 5 Size(mms): 1581 x
441 x 750Type no.(16O)
17 Faculty Unit
(2)
These veneer top desks have a designer perforated modesty panel in mild steel. Comprising a desk,a return unit, credenza and a free standing pedestal . veneer Top : 48 mm thick veneer top coated with melamine; 48 mmTop=4 mm Veneer+25 mm top plain particle board+ 18 mm baton+backing decorated laminated. Legs: MS ERW round tube of Dia 50.8 X 1.6 mm thick. Modesty & Side Panel : Perforated MS Sheet of 0.9 mm thick.Veneer Top : 48 mm thick veneer top coated with melamine; 48 mmTop=4 mm Veneer+25 mm top plain particle board+ 18 mm baton+backing decorated laminated.Pedestal : Shell : 0.8 mm Thick, Drawer Trey : 0.6 mm Thick, Drawer
Size(mms): 1500W x 750D
x 750HType no.(17A)
Size(mms): 1650W x 880D
x 750HType no.(17B)
Size(mms): 2062W x 880D
x 750H Type no.(17C)
Size (mms): 1200W x 450D
x 750HType no.(17D)
MMD, IIT BOMBAY Page no. 34 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Front: 0.8 mm Thick, Sides: Double extension ball sides.Glass door unit: Body: 0.8mm Thick MS, Glass: 0.6mm Thick clear glass.
Size(cms): 1675W x 450D
x 750HType no.(17E)
Size(cms):900W x 450D x
750HType no.(17F)
Pedestal(cms) Size:390W x 590D x 646H
Type no.(17G)
Size(mms): 1188 x 440 x
750Type no.(17H)
Size(mms): 1188 x 440 x
750Type no.(17 I)
Size(mms): 1580 x 440 x
750Type no.(17 J)
Size(mms): 1580 x 440 x
750Type no.(17K)
Size(mms): 1580 x 440 x
750Type no.(17 L)
MMD, IIT BOMBAY Page no. 35 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Pedestal 390 (w) 440 (D) X 646 (h)Type no.(17M)
Pedestal is made up of 0.8 thk CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, RearSide Stiffener,1.2 thk CRCA Top Stiffener & Bottom stiffener.All Drawers with Double extension precision ball slide,390 wide Pedestals File drawer.For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Knobs rovided on rawer only for free standing and Credenza.Pedestal. Locking • 10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism for ‘BoxBox File’ Pedestal.Finish : Epoxy Polyester Powder coated to the thickness of 50 microns (+/10).
Extended Return Unit
Type no.(17 N)
This fine range of postformed desks are complemented by side units and storage unit options to form the complete suite and are available in different sizes and colour options. Top: 25 mm thick plain particle board (ppb) clad with 0.6mm thick post formed laminate and 1mm thick backinglaminate (bdl). flat edge duly sealed with 2mm thick Side Panel: PVC beading. Modesty:18mm thick plain particle board (ppb) clad with 1.0mm thick decorative laminate (dl) on both. Sides. edge sealed with 2mm thick pvc beading.
LHS Size WDH (mms):
1550X450X705Type no.(17 O)
RHS Size WDH (mms):
1550X450X705Type no.(17 P)
HDU Size WDH (mms):
1280X425X705Type no.(17 Q)
This fine range of postformed desks are complemented by side units and storage unit options to form the complete suite and are available in different sizes and colour options. Top: 25 mm thick plain particle board (ppb) clad with 0.6mm thick post formed laminate and 1mm thick backinglaminate (bdl). flat edge duly sealed with 2mm thick Side Panel: PVC beading.Doors:18mm thick plain particle board (ppb) Partitions,Shelves: clad with 1.0mm thick decorative laminate (dl) on both sides. edge sealed with 2mm thick pvc beading.
CONFERENCE ROOM FURNITURE
18 Conference table 1
Work surface should be made up of 12mm THK toughened glass with back painted design on to under side and crystal edge polish finish. Construction should be knock down construction.All panels are made from 36mm Thick Pre–laminated board (interior grade) with 2mm
8 Seater Curve/StraightType no.(18 A)
10 Seater Curve/Straight
MMD, IIT BOMBAY Page no. 36 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Type no.(18 B) thick. PVC edge beading. Understructure consisits of storage for cpu, projector and paper storage. Provision for glass adjustment for glass aligning. Legrand electricals are used for wire management on to centre suport beam panel and cpu storage area for socket connections,RJ11,RJ45.
12 Seater Curve/StraightType no.(18 C)
14 Seater Curve/StraightType no.(18 D)
19 Conference Table 2
This eco modular conference table enables various configurations to suit different conference rooms. It is made of particle board and has wire management facilities for uncluttered wiring. It has profiled legs with twin colored modesty for better looks. # Overall dimensions (mms) Single Seat 675.0W X 600.0D X 750.0H Double Seat 1350.0W X 600.0D X 750.0H Top work surface thickness is 25mm PLB with PVC beading allover. Legs are made from 18mm thick PLT having curved profile. Madesty made from PLT (Prelaminated Twin)boards 18mm thick in two shades. A Wire Manager running along the width of desk fitted on the modesty Panel from Inside.
MMD, IIT BOMBAY Page no. 37 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
STORAGE FOR FACULTY AND ADMINISTRATION STAFF
20 2 Drawer Vertical filing
cabinet
Vertical filing cabinet Models & Product Size 2 Drawer:Width: 470mm Height: 710mmDepth: 620mm; 4 Drawer Width: 470mm Height: 1320mm Depth: 620mm. Construction:Rigid Knock Down Construction Material:CRCA 0.7 mm Thick (Top, Side & Drawer Front);0.6 mm Thick (Frames, Drawer Inside Cover, Side Back Side)0.5mm Thick (Back, Bottom, Drawer Bottom) Drawer front:Easy to grip Full length Handle recess integrated into Metal Drawer fronts Label Holder Snap on type plastic label holder on Drawer Fronts Drawer Size & Files type For hanging office files (Foolscap) from front to back (Files Along theWidth) No. of 20 mm thk file which can be hanged in above way per drawer is 28.Locking & antitipping arrangement Centralized locking with 10 lever Cam Lock&having antitipping arrangement to ensure that when one drawer is opened for use, it does not allow other drawers to be opened.Slide High quality precision ball slide. Drawer Load:40 kg. UDL for 75,000 cycles (BS)Triangular Plate Plain Triangular plate pop riveted at the bottom corners for rigidity. Accessories (Optional) Drawer Partition § Cradle for hanging A4 file folders front to back Finish:Epoxy Polyester Powder coated to the thickness of 50 microns (+/10).
MMD, IIT BOMBAY Page no. 38 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
21 4 Drawer Vertical filing
cabinet
Vertical filing cabinet Models & Product Size 2 Drawer:Width: 470mm Height: 710mmDepth: 620mm; 4 Drawer Width: 470mm Height: 1320mm Depth: 620mm. Construction:Rigid Knock Down Construction Material:CRCA 0.7 mm Thick (Top, Side & Drawer Front);0.6 mm Thick (Frames, Drawer Inside Cover, Side Back Side)0.5mm Thick (Back, Bottom, Drawer Bottom) Drawer front:Easy to grip Full length Handle recess integrated into Metal Drawer fronts Label Holder Snap on type plastic label holder on Drawer Fronts Drawer Size & Files type For hanging office files (Foolscap) from front to back (Files Along theWidth) No. of 20 mm thk file which can be hanged in above way per drawer is 28.Locking & antitipping arrangement Centralized locking with 10 lever Cam Lock&having antitipping arrangement to ensure that when one drawer is opened for use, it does not allow other drawers to be opened.Slide High quality precision ball slide. Drawer Load:40 kg. UDL for 75,000 cycles (BS)Triangular Plate Plain Triangular plate pop riveted at the bottom corners for rigidity. Accessories (Optional) Drawer Partition § Cradle for hanging A4 file folders front to back Finish:Epoxy Polyester Powder coated to the thickness of 50 microns (+/10).
MMD, IIT BOMBAY Page no. 39 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
22 CUPBOARD MAJOR WITH 4 SHELVES
1. The cupboard should be Plain with 4 Shelves The raw material used in cupboard should be PRIME quality, CRCA should be as per IS513(1994,1998) ‘D’ grade 2 .Dimensions: 915 mm (W) x 485 mm (D) x 1980 mm (H), (Variations in Dimension within +/ 3% is acceptable).3. The Cupboard should have Welded construction.4. The material used for constructing thecupboard should be at least 0.8 mm thick Cold Rolled Close Annealed (CRCA) Steel for Back, Shelf & at least 0.9 mm thick CRCA for all other components.5. The doors provided should be Full height Steel Hinged Doors6. The handle provided should be matching, easy to grip, sleek and elegant.7. The Cupboard should have a 3 way locking mechanism with shooting bolt arrangement.8. Shelving :8.1 The shelving should be Height wise Adjustable and Shelf Mounting.8.2 The Uniformly Distributed Load Capacity per each full shelf should be 80 Kg at least.8.3 The cupboard should have 4 numbers of adjustable full shelves.9. The cupboard should have Epoxy Polyester Powder finishing coated to the thickness of 50 microns (+/10). After 10 tanks anti rust treatment.
MMD, IIT BOMBAY Page no. 40 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
23 Cupboard (Glass Door)
Size: 914 mm (W) x 320mm (D) x 1742 mm (H) for 4 Door. Rigid knock down construction.Top panel, Back panel and side panel are made from 0.7mm high yield strength CRCA, rest in 0.8mm CRCA.Each door has 6 lever Cam lock with common keys.Each door has 3mm thk transperent glass for clear inside vision secured in a Metal frame through rubber gasket.Each door has a Scissor mechanism for receding inside the top of the respective compartment & ensures parallel and smooth movement.Each door has plastic side end caps as Handle which is easy to grip.Each Compartment has storage shelf.Uniformly Distributed load capacity per each shelf is 80 kg max.4 Door has inside Metal top panel.2 Door has 18 mm PLB top straight edge with PVC lipping.Epoxy polyster powder coated to thickness of 50 microns(+10).
24 Personal Locker Unit with 4 individual lockers
Overall size: H72" × W15" × D18" Size of Each locker: H435 × W380× D457 (mm) CRCA IS 513 ‘D’ grade steel 06 mm. Shelf UDL capacity per each shelf is 35 Kg. 10 lever camLock on each door. Label holder on each door for case of identification. Perforation on each for ventilation. Epoxy polyester powder coated to the thickness of 50 microns All steel parts are powder coated in high quality powder after 10 tanks anti rust treatment oven baked in 210 C to give unique everlasting finish.
25 Study Table 1. Table Top is rectangular shaped with 6 Study Table for rounded corner. 2. Frame of the Table are made of MS Square tubes of ERW Quality of thickness 1.25mm confirming to BIS (IS 7138 – 19733. Table Top is made of Prelaminated board of 25mm with decorative laminate and with hot glued PVC Lipping around the periphery. 4. Frame of Table is powder coated in black color and drawer unit painted in TA Grey color. 5. Two legs with level adjusters.
MMD, IIT BOMBAY Page no. 41 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
6. Modest panel with square embossed dots for good looks & strength starts from MODEL T 4.5 x 2.25, MODEL T 5 x 3, MODEL 6 x 3. 7. Drawer Unit is with 3 Drawers on lefthand side of Table. Locking Top Drawer,other two drawers will also get automatically locked. 8. Locker Unit is with one shelf inside on right handside of Table. 9. Drawer Unit components are made of MSCRCA Sheets of Thickness 0.63mm, 0.8mm,1.25mm + 1.6mm conforming to BIS (IS 513 1986). 10. Dimensions of MODEL T 4 x 2 = 755 H x 1200 W x 600 D (mm)
26 Single Bed (1)
Single Bed for hostels. Overall size : L030 x W 865 x H985 mm Mattress size : L905 x W790 mm Seating Height : 395 mm Backrest panel : 100 degree with horizontal Material Description: Bed structure made of OD – 38 mm x 1.2 mm (18 SWG) thick ERW round tube (CRC). Bed mattress frame & 4 nos. centre support of 25 x 25 x 1.6 mm (16 SWG) thick ERW square tube (CRC) Mid Panel of 18 mm thick full length marine ply with bolted with mattress frame at bottom side. Backrest panel & lower storage unit (open type) of 18 mm thick. Marine ply with both side 1.2 mm thick laminated & 2 mm PVC beading all over edge. 3 nos. main structure support made of OD 19 mm x 1.6 mm (16 SWG) thick ERW round tube (CRC) Good quality PVC shoes. All steel parts in powder coated finished with high quality powder after 10 tank anti rust treatment.
27 Single Bed (2)
Single Bed for hostel and Barrack. Overall size: H27" × L78" × D36" [ L6.5' x D3' feet]
MMD, IIT BOMBAY Page no. 42 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Material Specification: • Bed frame structure made up of prime quality CRC (M.S) rectangular tube 25x50x1.2 mm (18 SWG.) • Bed body made up from prime quality 0.8mm (22 SWG) CRCA sheet of 'D' grade Steel IS 513. • Good quality Plastic Shoes. • All steel parts in Powder Coated finished with standard quality powder after 10 tanks antirust treatment in our own in house plant • Knockdown construction.
MMD, IIT BOMBAY Page no. 43 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
(B) TECHNICAL BID FOR MODULAR / CUSTOMISED FURNITURESr. No.
Type Particulars with details specification
Sample Image Compliance
(Yes / No)
If any
Deviation
mention
1 (WORKSTATION TYPE1) RECTANGULAR
1 PERSON MODULE NON SHARED 1200
X 600Type NO. (1A)
Manufacturing assembling, transporting & placing in position worktops 25 mm thk. Prelaminated particle board (as per IS:12823) with approved laminate externaly and balancing laminate on bottom surface , cut to size & shape as per design & drawings. Edges to be fixed with 2 mm thk PVC edge lipping of approved make & matching to laminate, which is glued with hotmelt EVA glue. Understructure Legs to be fabricated by CO2 welding. Made up of section 50.8mm x50.8mm (IS: 7138 ERW tube, 50.8mm x 25mm x 16bg) with base plate of the MS tube is fitted with glided plate of 47 x x 47 x 5mm (IS: 2062, 5 mm HR). M8 levelers to be provided for height adjustment of 50mm. Finish to be in epoxy polyster power coated with 40 to 50 microns.For floating look of table, spacers (outer dia 20 x 20mm ht) are provided which are fixed on main leg & table top. Spacers are plastic molded.Wiremanagement Wire tray which is attached below worksurface to carry wires horizontly, is made up of combination of 3mm & 5mm dia MS rod (IS: 9550 bright bar) along with 5mm thk MS plate (IS: 2062 5mm HR). Height of tray to be 45mm. Tray to be powder coated. Access flap to access switches which are
2 PERSON SIDE BY SIDE MODULE 1200 X 600Type NO. (1B)
4 PERSON BACK TO BACK MODULE 1200X 600Type NO. (1C)
6 SEATER BACK TO BACK MODULE 1200 X 600Type NO. (1D)
8 SEATER BACK TO BACK MODULE 1200 X 600Type NO. (1E)
MMD, IIT BOMBAY Page no. 44 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification
Sample Image Compliance
(Yes / No)
If any
Deviation
mention
mounted on MS power box (below worktop). Made from Aluminium extrusion and ABS milded ends are capped to both ends of extrusions. Flap is connected with 90 deg hinge which is fitted on the inside edge of the aluminium extrusion making them discreet. Cable pole To carry wires vertically from junction box to wirecarrier. Cable pole assembly to be made of 705mm L x 333mm W x 0.8 mm thk. In between divider angle to seperate data cable from power cable to be made of 540 mm L x 83.5 mm W & 0.8 mm thk.To be coated with 45 microns thk of epoxy powder coating. Screens A.With Aluminium extrusions frames 18mm block with in frame of Aluminium Extrusion sections (HE9, IS:63400) of thickness 23mm. Corners are covered with Aluminium Die cast caps finished with PVC flat edge band /Tmould to give a clear edge. Screen finish Double block Fabric Magnetic screen + White Board screen 23 mm thk plain partical board with GI sheet pasted on it and than fabricis wrapped all around. Edges to be covered with T mould and white baord made up of 18mm prelaminated board with 2mm PVC lipping all around respectively. Ht of screen shall be 642 MM FOR 1200 MM HT OF SYSTEM.Work top 25 mm thk. Prelaminated particle board (as
MMD, IIT BOMBAY Page no. 45 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification
Sample Image Compliance
(Yes / No)
If any
Deviation
mention
per IS:12823) with approved laminate externaly and balancing laminate on bottom surface, cut to size & shape as per design & drawings. Edges to be fixed with 2 mm thk PVC edge lipping of approved make & matching to laminate, which is glued with hotmelt EVA glue. Size of worktop will be as per layout 1200 MM WIDTH X 600 MM DEPTH.Pedestal 3 drawer pedastal unit (box + box + file) of over all size 646H X 390W X 435D made out 0.8mm thk CRCA for body shell, drawer tray, front & rear side stiffner. Top & bottom stiffner of 1.2mm thk. Drawer front & top.All slides with double extension precision ball slide. Drawers to be without handles for clean finish. For drawer pulling, side wise tapered recess provided in shell behind drawer fronts. Drawer width to accomodate fullscape office files in depthwise manner, A4 files in width wise manner. 10 lever cam lock & central locking with actuator & lock channel mechanism. Metal finish to be in epoxy polyster power coated with 40 to 50 microns.
2 (WORKSTATION TYPE2)
PENTAGONAL1 PERSON
MODULE NON SHARED 1500 X 1500 X 600
Type NO. (2A)
Manufacturing assembling, transporting & placing in position worktops 25 mm thk. Prelaminated particle board (as per IS:12823) with approved laminate externaly and balancing laminate on bottom surface , cut to size & shape as per design &
MMD, IIT BOMBAY Page no. 46 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification
Sample Image Compliance
(Yes / No)
If any
Deviation
mention
drawings. Edges to be fixed with 2 mm thk PVC edge lipping of approved make & matching to laminate, which is glued with hotmelt EVA glue.Legs to be fabricated by CO2 welding. Made up of section 50.8mm x50.8mm (IS: 7138 ERW tube, 50.8mm x 25mm x 16bg) with base plate of the MS tube is fitted with glided plate of 47 x x 47 x 5mm (IS: 2062, 5 mm HR). M8 levelers to be provided for height adjustment of 50mm. Finish to be in epoxy polyster power coated with 40 to 50 microns.For floating look of table, spacers (outer dia 20 x 20mm ht) are provided which are fixed on main leg & table top. Spacers are plastic molded. Wiremanagement Wire tray which is attached below worksurface to carry wires horizontly, is made up of combination of 3mm & 5mm dia MS rod (IS: 9550 bright bar) along with 5mm thk MS plate (IS: 2062 5mm HR). Height of tray to be 45mm. Tray to be powder coated. Access flap to access switches which are mounted on MS power box (below worktop). Made from Aluminium extrusion and ABS milded ends are capped to both ends of extrusions. Flap is connected with 90 deg hinge which is fitted on the inside edge of the aiuminium extrusion making them discreet. Cable pole To carry wires vertically from junction box to wirecarrier. Cable pole assembly to be made of 705mm L x
T MODULE 1500 X 1500 X
600Type NO. (2B)
4 PERSON + MODULE
Type NO. (2C)
MMD, IIT BOMBAY Page no. 47 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification
Sample Image Compliance
(Yes / No)
If any
Deviation
mention
333mm W x 0.8 mm thk. In between divider angle to seperate data cable from power cable to be made of 540 mm L x 83.5 mm W & 0.8 mm thk. . To be coated with 45 microns thk of epoxy powder coating. Screens A.With Aluminium extrusions frames 18mm block with in frame of Aluminium Extrusion sections (HE9, IS:63400) of thickness 23mm. Corners are covered with Aluminium Die cast caps finished with PVC flat edge band /Tmould to give a clear edge. Screen finish Double block Fabric Magnetic screen + White Board screen 23 mm thk plain partical board with GI sheet pasted on it and than fabricis wrapped all around. Edges to be covered with T mould and white baord made up of 18mm prelaminated board with 2mm PVC lipping all around respectively. SINGLE block Fabric Magnetic screen 23 mm thk plain partical board with GI sheet pasted on it and than fabricis wrapped all around. Edges to be covered with T mould a Ht of screen shall be 642 MM FOR 1200 MM HT OF SYSTEM.Work top 25 mm thk. Prelaminated particle board (as per IS:12823) with approved laminate externaly and balancing laminate on bottom surface, cut to size & shape as per design & drawings. Edges to be fixed with 2 mm thk PVC edge lipping of approved make & matching to laminate, which is glued with
MMD, IIT BOMBAY Page no. 48 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification
Sample Image Compliance
(Yes / No)
If any
Deviation
mention
hotmelt EVA glue. Size of worktop will be as per layout 1500 MM W1 X 1500 MM W2 X 600 D.Pedestal 3 drawer pedastal unit (box + box + file) of over all size 646H X 390W X 435D made out 0.8mm thk CRCA for body shell, drawer tray, front & rear side stiffner. Top & bottom stiffner of 1.2mm thk. Drawer front & top . All slides with double extension precision ball slide. Drawers to be without handles for clean finish. For drawer pulling, side wise tapered recess provided in shell behind drawer fronts. Drawer width to accomodate fullscape files in depthwise manner, A4 files in width wise manner. 10 lever cam lock & central locking with actuator & lock channel mechanism. Metal finish to be in epoxy polyster power coated with 40 to 50 microns.
3 (WORKSTATION TYPE3)
PENTAGONAL1 PERSON MODULE
Type NO. (3A)
52.4 mm thk. 1200 panel based work station partition with flexible construction offering various functional and decorative finishes as well as cable management capacity. All trims made of aluminium extrusions. Blocks made out of a composite construction of MDF and paper honeycomb with fabric wrapped on it. Tiles should be slid in to the panels from top before fixing
MMD, IIT BOMBAY Page no. 49 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification
Sample Image Compliance
(Yes / No)
If any
Deviation
mention
the top horizontal. Top tile to be in Fabric magnetic + white board. These tiles to be supported from top & bottom side with clips made from PP co polymer fitted in horizontal extrusion. Bottom tile and leg to be made of Mild steel with epoxy powder coated.Fabricated bottom frame as a welded structure of steel components. The panels and worktops to be supported with MS legs with levelers at various locations depending on the layout requirements.Work top shall be made of 25mm thick Pre laminated particle board interior grade of approved Architect shade conforming to IS: 12823. Bottom shall have a backing laminate of minimum 0.6 mm thickness. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping and the size shall be 1500 mm w1 x 1500 mm w2 x 600 mm d.Plain Metal tiles are made of 0.6 mm thick M.S. CRCA Grade D as per IS: 513 powder coated with Epoxy Polyester finish.Fabric magnetic tiles are fabric upholstered metal tiles in 0.6 mm thick G.I. Grade. White board tiles are made of 8.0 mm thick particle board laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and having all its edges with minimum 0.5 mm thick PVC edgingPlain Metal tiles are made of 0.6 mm thick M.S. CRCA Grade D as
2 PERSON T MODULE
Type NO. (3B)
4 PERSON + MODULE
Type NO. (3C)
MMD, IIT BOMBAY Page no. 50 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification
Sample Image Compliance
(Yes / No)
If any
Deviation
mention
per IS: 513 powder coated with Epoxy Polyester finish.Fabric magnetic tiles are fabric upholstered metal tiles in 0.6 mm thick G.I. Grade. White board tiles are made of 8.0 mm thick particle board laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and having all its edges with minimum 0.5 mm thick PVC edgingPedestal Size 646mm H X 390mm W X 435 mm D. 3 drawer pedastal unit (box + box + file) to be made out 0.8mm thk CRCA for body shell, drawer tray, front & rear side stiffner. Top & bottom stiffner of 1.2mm thk. All slides with double extension precision ball slide. Drawers to be without handles for clean finish. For drawer pulling, side wise tapered recess provided in shell behind drawer fronts. 10 lever cam lock & central locking with actuator & lock channel mechanism. Metal finish to be in epoxy polyster power coated with 40 to 50 microns.
4 (WORKSTATION TYPE4)
RECTANGULAR1 PERSON
MODULE NON SHARED 1200
X 600Type NO. (4A)
52.4 mm thk. 1200 panel based work station partition with flexible construction offering various functional and decorative finishes as well as cable management capacity. All trims made of aluminium extrusions. Blocks made out of a composite construction of MDF and paper 2 PERSON SIDE
MMD, IIT BOMBAY Page no. 51 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification
Sample Image Compliance
(Yes / No)
If any
Deviation
mention
BY SIDE MODULE 1200
X 600Type NO. (4B)
honeycomb with fabric wrapped on it. Tiles should be slid in to the panels from top before fixing the top horizontal. Top tile to be in Fabric magnetic + white board. These tiles to be supported from top & bottom side with clips made from PP co polymer fitted in horizontal extrusion. Bottom tile and leg to be made of Mild steel with epoxy powder coated.Fabricated bottom frame as a welded structure of steel components. The panels and worktops to be supported with MS legs with levelers at various locations depending on the layout requirements.Work top shall be made of 25mm thick Pre laminated particle board interior grade of approved Architect shade conforming to IS: 12823. Bottom shall have a backing laminate of minimum 0.6 mm thickness. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping and the size shall be 1200 MM W X 600 MM D.Plain Metal tiles are made of 0.6 mm thick M.S. CRCA Grade D as per IS: 513 powder coated with Epoxy Polyester finish.Fabric magnetic tiles are fabric upholstered metal tiles in 0.6 mm thick G.I. Grade. White board tiles are made of 8.0 mm thick particle board laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and having all its edges with minimum 0.5 mm
4 PERSON BACK TO BACK
MODULE 1200X 600
Type NO. (4C)
6 SEATER BACK TO BACK
MODULE 1200 X 600
Type NO. (4D)
8 SEATER BACK TO BACK
MODULE 1200 X 600
Type NO. (4E)
MMD, IIT BOMBAY Page no. 52 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification
Sample Image Compliance
(Yes / No)
If any
Deviation
mention
thick PVC edging. Plain Metal tiles are made of 0.6 mm thick M.S. CRCA Grade D as per IS: 513 powder coated with Epoxy Polyester finish.Fabric magnetic tiles are fabric upholstered metal tiles in 0.6 mm thick G.I. Grade. White board tiles are made of 8.0 mm thick particle board laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and having all its edges with minimum 0.5 mm thick PVC edging Pedestal Size 646mm H X 390mm W X 435 mm D. 3 drawer pedastal unit (box + box + file) to be made out 0.8mm thk CRCA for body shell, drawer tray, front & rear side stiffner. Top & bottom stiffner of 1.2mm thk. All slides with double extension precision ball slide. Drawers to be without handles for clean finish. For drawer pulling, side wise tapered recess provided in shell behind drawer fronts. 10 lever cam lock & central locking with actuator & lock channel mechanism. Metal finish to be in epoxy polyster power coated with 40 to 50 microns.
5 Class Room Table
1 Seater CPU / Laptop WxDxH (mms): 900 x
600 x 680Type No. (5A)
WorkSurface shall be 25mm Thick (±1mm): Base Material 25mm Thick Prelaminated particle board.2mm Thk PVC edge banding on straight outer edges (Available in matching colour and contrast colour as per colour chart) 2 Seater CPU
MMD, IIT BOMBAY Page no. 53 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification
Sample Image Compliance
(Yes / No)
If any
Deviation
mention
WxDxH (mms): 1500 x 600 x
680Type No. (5B)
Modesty is18mm Thick (±1mm) :Base material 16mm Plain particle boardPostlaminated with 0.6mm Top laminate on either side 2mm Thk and 0.8mm Thk PVC edge banding of matching colour on outer edges of modesty Legs are made from 1.6mm Matt silver Anodized Aluminium extrusion. Legs assembled together with 8mm thick MS powder coated plate at bottom and 5mm thick MS powder coated plate at topThe Base support plate is having provision for wire entry and glide fixing The wire carrying is facilited through the hollow space between two leg extrusions and the wires are concealed between removable rigid PVC extrusion in the leg Max. 20 nos. of Dia 6 wires can be passed through the space between two leg extrusions Powder coated table support brackets made from 2mm thick MS shee provided for . overall product stability.Powder coated stopper made from 1.5mm thick Aluminium extrusion fixed with worksurface by powder coated stopper bracket made from 3mm thick MS sheet.Both ends of Aluminium extrusion covered with plastic moulded End capMade from plastic moulded components to facilitate access of Electrical/Data/Voice sockets access from Top. Powder coated switch mounting tray made from 0.8mm and 2mm thick MS sheet fitted on modesty through which
2 Seater Laptop WxDxH (mms):
1350 x 600 x 680
Type No. (5C)
3 Seater CPU / Laptop WxDxH (mms):2700 x
600 x 680Type NO. (5D)
4 Seater Laptop WxDxH (mms):
2700 x 600 x 680
Type No. (5E)
4 Seater CPU WxDxH (mms):
3000 x 600 x 680
Type No. (5F)
6 Seater CPU WxDxH (mms):
4500 x 600 x 680
Type No. (5G)
6 Seater Laptop WxDxH (mms):
4050 x 600 x 680
Type No. (5H)
MMD, IIT BOMBAY Page no. 54 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Sr. No.
Type Particulars with details specification
Sample Image Compliance
(Yes / No)
If any
Deviation
mention
cables can be passed. Switches to be mounted on tray asper requirement. Powder coated Cable tray made from 0.6mm thick MS sheet hooked on switch mounting tray for keeping extra length Electrical/Data/Voice cables
MMD, IIT BOMBAY Page no. 55 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
(C) TECHNICAL BID : LAB FURNITURE / FUME HOOD
TECHNICAL SPECIFICATIONS
A) CFRAME SYSTEMAll CFrames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA/G.I (Cold Rolled Close Annealed/Galvanized Iron) confirming to IS Code 513:1994. The suspended underbench welded units should be supported on heavyduty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. Cframe should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This shall provide more knee space or leg space and would facilitate uninterrupted lateral movement of the underbench units within the bench run. The Cframe legs should be supplied with adjustable feet (tolerance from 5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus.
MMD, IIT BOMBAY Page no. 56 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. The structure should have a removable back panel to provide access for maintenance throughout the length of table. The Cframe shall also have skirting at back bottom side. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths should be 620 mm, 770 mm and 920 mm for wall side and 1240mm, 1540mm, 1840mm for Island tables. The Corner Units shall fit well with 770mm & 920mm table depths. All framework is should be pretreated with superior pure epoxy powder coated finish.The CFrames should be for suspended storage cabinets or for cabinets that can slide throughandthrough from one end of the workbench to the other through CFrames (configuration depends upon the Schedule of Quantities)
B)HORIZONTAL MEMBERS These should be made from rectangular pipes of 2mm thickness. Crosssectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA/GI MS and coated with pure epoxy powder. These connect two CFrames together as shown using Cclamps/Uclamps. Together with the CFrames and Horizontal Members connected together, the skeletal structure of the workbench is formed on which the worktop can be placed and the hangingtype storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent CFrames. They should be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800
These cover panels cover the service lines that run behind them. These should be easily removable (unclipped) and the service line be accessed for maintenance. This allows the equipment on workbench to remain undisturbed They should be made of CRCA/GI MS with pure epoxy powder coating and are of 1mm thickness
MMD, IIT BOMBAY Page no. 57 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
C)COVER PANELSAll side cover panels and back panels, filler panels should be made from CRCA/GI MS panels of 1.0mm thickness with pure epoxy powder coating.
MMD, IIT BOMBAY Page no. 58 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
MMD, IIT BOMBAY Page no. 59 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
MMD, IIT BOMBAY Page no. 60 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
D)VERTICAL UPRIGHT The Upright system will form the backbone for internal distribution of GDS, Electrical supply systems Shelves and Top Units and should be constructed from 16 gauge CRCA/GI formed steel panels with removable covers. Shelf height should be adjusted with an increment of 1inch / 25mm. Upright should also provide support to Top Units for hanging thus eliminating the danger of fixing the Top Units on nonrigid partition wall / panels. Uprights should be supplied with adjustable feet from 5mm to +20mm.
E) ELECTRICAL BOOMElectrical Boom shall be made out of 18gauge CRCA steel panels and shall span the length between uprights and will be provided with removable service panels. Electrical and GDS supplies shall be supplied through this Electrical Boom . Boom shall be supplied with factory fitted combinations of switch & sockets with 15 amps standard grade.
MMD, IIT BOMBAY Page no. 61 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
F)TABLE MOUNTED ELECTRICAL TRUNKINGUsed for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking should be made from 1.0 mm thick CRCA/GI MS panel. It should be available in both, single sided and double sided configurations. It should be made from CRCA/GI MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope
MMD, IIT BOMBAY Page no. 62 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
G) ELECTRICAL FITTINGS AND ACCESSORIESService fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.
H)REAGENT SHELVESH1 ALUMINIUM EXTRUSION SHELF WITH GLASSDepending upon BOQ requirement, height adjustable shelves should be provided between uprights with 1” of height adjustability. Complete modular design consisting of 2 stage horizontal storage shelves. The ends and intermediate vertical supports should be 2mm thick aluminum extrusion with MS brackets of 2 mm thick. Toughened glass should be puton over these shelves for taking care of bottle marks/corrosion. The depth of the shelf should be at least 300mm. Sliding mechanism of reagent shelves will not be acceptable as their stability reduces over a period of time, only positive catching of the shelves on uprights will be acceptable
MMD, IIT BOMBAY Page no. 63 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
H2) FIXED TYPE REAGENT SHELFFixedType reagent shelves should be provided. It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets. It should have provision for placing Granite pieces as per requirement
MMD, IIT BOMBAY Page no. 64 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
I) OVERHEAD CABINETSThe construction should be the same as the underbench cabinets. Knockdown design off storages will not acceptable as their strength is not as good as that of the welded cabinets.The height of these cabinets should be around 635mm while the depth should be around 340mm. The shutters should be available in two options: Metal shutters and Metal frame with inserted glass. There should be one heightadjustable shelf inside each cabinet. Other construction should be similar to underbench cabinet
MMD, IIT BOMBAY Page no. 65 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
J)STORAGE UNITWelded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel.Knockdown design off storages will not acceptable as their strength is not as good as that of thewelded cabinets.It should be relocated anywhere easily as it is an independent unit. Cabinet should be of square nonsharp edge construction. Doors should be assembled with SS304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front is of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Storage Units to be of the following types:
1. Suspended Type
2. Sliding Type
3. Castorbased Mobile Type
(Depending upon the requirement in the schedule of quantity)Dimensions: W=300/450/600/750/900 mm, D = 530mm/570mm H = 635/485 , 675/525 mm. Configurations: 1 Shutter/ 2 Shutters + No Drawer/1 Drawer/2 Drawers/3 Drawers, MOC: MSCRCA: IS – 513 (1994), Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. Finish: Powder coating pure epoxy, thickness 4050 microns. Handle: Anodized Aluminum RecessedType,
MMD, IIT BOMBAY Page no. 66 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
CTC: 160.0mm. Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit). Hinge: Knucklebutt type SS Hinge. Screw: SS304. Shutter should be of twintype construction with sound dampening effect using profeel. Shutter cover should be equipped with Bump on for sound dampening. Ball Slide: 500mm Length (required only for drawer unit). Shutter should have provision of roller catch
MMD, IIT BOMBAY Page no. 67 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
MMD, IIT BOMBAY Page no. 68 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
J46) Modesty Panels
These are CRCA/GI MS powder coated 1mm thick modesty panels to cover up gaps/openings at back or sides in the furniture benches.
J47) Back Support Brackets
MMD, IIT BOMBAY Page no. 69 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
These are metal brackets that support the service lines at the back of the workbench.
J48) Modesty Panels
In Floor mounted cabinets, the PVC skirting covers the metal skirting all around. It gives a curvature at the bottom that discourages dust accumulation and assists easier cleaning and protects the metal skirting from direct contact of floor cleaning acids.
K)ANTIVIBRATION TABLE The table consists of following parts:
• Tubular frame Completely modular type tubular frame, which carries the load of kadappa and granite, kept on it. Hightension Pan Head M6 Zinc blackcoated screws (for better corrosion resistance) are used for the fastening. The material used is: 40Sq x 1.6 mm thick ERW tube and the overall load carrying capacity of tubular frame is 250 kgs of uniform distributed load.
• Cover Panels – They are 0.8 mm thick CRCA /GI MS sheet and pretreated and epoxy powder coated for better corrosion resistance. The thickness of powder coat is 4550 microns which passes the test of Salt Spray for 1000 Hours and having the Scratch Hardness of 3 Kgs.
• Kadappa 25mm thick Kadappa acts as the shockdampening component.
• Work Surface – granite
• Vibration Isolating Rubber pads The objective of using these rubber pads is to absorb the pulsating vibrations coming from the floor .The pads are made up from combination of nitrite rubber, cork particles and cross linked polyester fiber. This highgrade compound material possesses all the physical and mechanical properties required to minimize the dampening effect
• Leveling screws The Tubular frame has the provision for 4 height adjusters or Leveling Screws that take care of all leveling aspects.
• Size: (Width: 900mm, Depth: 600mm , Height: 900mm)
MMD, IIT BOMBAY Page no. 70 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
L1) LABORATORY SINK AND ACCESSORIES
L11) SS Sink
MMD, IIT BOMBAY Page no. 71 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
L12) Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Standard bowl size (L x W x D) is 500 x 400 x 300 mm.
L13) Cup Sink Oval Drip Cup :
MMD, IIT BOMBAY Page no. 72 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
L14, 5)AntiSiphon Bottle trap / Flexible/ F ; Connector Size : 38mm x Length = 1m
L16) PEG BOARDSThese should be Single faced high grade stainless steel pegboard having a tray hole for water drainage and detachable pegs. The essence should be made up of I mm thick stainless steel (SS 304) / Acrylic whereas the pegs should be made up of polypropylene and should be adjustable with a minimum 10mm distance between each peg
MMD, IIT BOMBAY Page no. 73 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
L17) 3 Way Faucet Bench mounted 3 way water fittings with 8" swing gooseneck
Water faucets and valve bodies should be cast red brass alloy or bronze forgings. All fittings should be powder coated.
L18) Single Water Faucet Deck mounted, 8" swing gooseneck
L19) Twoway Deck Mounted Eye WashDeck mounted drench hose units should have a single outlet head with a rubber protective collar and should deliver an aerated flow of water. The valve should be forged brass selfclosing type with a stainless steel squeeze handle. Units should be furnished with a deck flange and an 8 ft. reinforced PVC hose
MMD, IIT BOMBAY Page no. 74 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
L110) Floor Mounted PVC emergency safety shower with eyewash
FLOOR BASED PVC EMERGENCY SHOWER CUM EYEWASH – Corrosion resistant, combination eye wash/shower safety station with ABS plastic shower head, ABS plastic bowl, cast aluminium powder coated flag handle, PVC floor flange, 2” IPS Schedule 80 PVC pipe and fittings, 1” IPS and ½” IPS U.S. made PVC coated brass stay open ball valves, and polished stainless steel pull rod. Unit shall have (2) polypropylene spray heads with integral dust covers, filters, and 1.8GPM flow control orifices mounted on a PVC coated brass head assembly. Unit shall include ANSI compliant sign
MMD, IIT BOMBAY Page no. 75 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
M) GAS VALVE
M1)Singleway Gas Valve for Non Burning Gases
M2)Twoway Gas Valve for Non Burning Gases
MMD, IIT BOMBAY Page no. 76 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
M3)Singleway Gas Valve for Burning Gases
M4)Twoway Gas Valve for Burning Gases
N) SPOT EXTRACTORSGeneral description Extractor arms mainly for use in chemical environments, where an extended resistance against chemical substances is a demand. All aluminium parts should have a double anodized surface protectionArm sections – Thin walled anodized aluminium sections with a very good corrosion resistance. Swivel – Swivel with 360 degree rotation. Add reduction for correct connection diameter. Joints – The adjustment knobs on the friction joints should be supported by ballbearings. The first joint should be supported by a spring (not Ø1001200). 360 degree rotation where indicated. Mini hood – The Mini hood should be supplied together with the arm and is also interface to the multipurpose and metal hood.
MMD, IIT BOMBAY Page no. 77 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Mounting – The arms can be mounted on ceilings, walls and floors or fixed to tables. By using an extension profile the arm’s operational reach must be increased. Other – All the arms should be provided with dampers, tight down to an under pressure of 3500 Pa. Air temperature 10 C to 70 C. Material recovery: 99% by weight.̊ ̊Components to be provided:Spot Extractor arm, Bracket for Spot Fume Extractor, Multipurpose hood (380mm x 460mm), Aluminium Extension Profile 1100mm Length, Reducer 7580 FR Spot Fume
DIMENSIONSConnection Direction
Diameter (mm)
A (mm) B (mm) C (mm) D (mm) Length (mm)
Up 75 250 700 500 250 1500
MATERIALSFlange PP
Tubes Aluminium, surface HMWhite
Joints PP with glass fibre reinforcement
Plastic rings PP with glass fibre reinforcement
Axial locking rings PP with glass fibre reinforcement
Adjustment knobs PP with glass fibre reinforcement screws in stainless steel
Threaded shaft inside joints Stainless steel
MMD, IIT BOMBAY Page no. 78 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Damper blade Thermo Plastic Elastomer
Damper adjustment handle Aluminium, anodized
Internal spring Stainless steel
Bearings swivel PP with glass fibre reinforcement
Swivel Aluminium
Rivets Stainless steel
Recommended airflows
Ø 50 50110 m3/h
Ø 75 110240 m3/h
Ø 100 200450 m3/h
O) OTHER LAB ACCESSORIES
O1) PLASTIC KBPT
O2) REV STOOL MCH HT ADJ + BACK HI BASE
MMD, IIT BOMBAY Page no. 79 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
P)CHEMICAL STORAGE CABINETS
It is used for storages of corrosive chemicals and is provided with a ventilation system to enable exhaust of localized fumes emanating from the chemicals stored.
P1) MS Chemical Storage Cabinet [with top cover plate] Size:1000 x 486 x 1800mm : 1.2mm thk.: The material should be is 1.2 mm CRCA/GI MS with pure Epoxy Powder coating. It must be fitted with a float glass to enable visibility inside the cabinet. It should also has louvers/perforations for air supply. The overall dimensions are 1000 x 486 x 1800 mm (W x D x H). The chemical storage cupboard must always be connected to exhaust to prevent corrosion from fumes emanating from acid containers
MMD, IIT BOMBAY Page no. 80 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
MMD, IIT BOMBAY Page no. 81 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
P2) Full PP Cabinet for Acid Storage Dimensions: 1000mm W x 486mmD x 1500mm H – Entire Cabinet made of Polypropylene with no metal parts/components exposed inside. It should have 4 loading levels inside with at least two adjustable shelves. There should be an exhaust path at the back of the cupboard on the inside to provide a guided path for exhausting the fumes. The doors should have provision for allowing air into the cupboard and should also have provision to allow locking of the cupboard doors. The shelf should be able to take a UDL of 30 kgs. The manufacturer should certify Spill Containment as per SEFA 8P and Spillage or Leakage Test of SEFA 11 with internal reports. The manufacturer should also submit a thirdparty Chemical Surface Finish Test as per SEFA 8P – No Level 3 conditions for the list of 49 reagents specified
MMD, IIT BOMBAY Page no. 82 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Other Dimensions: 540mm/700mm/840mm W x 530mm D x 630 mm H for storages under fume hood
P3) Cabinet for Flammable liquid storages with 10 mins fire rating (FM Approved) Size: 1092W X 457D X 1651H1 mm thick double wall construction, with 38mm insulating air space. Fully welded construction, dual vents with inbuilt flash arresters, selfindexing doors for closing in sequence, 3 loading levels with keyed 3point latch, builtin earthing connector. The cupboard has 51mm liquid tight containment sump. Make: Justrite/Eagle
MMD, IIT BOMBAY Page no. 83 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
P4) Cabinet for acids and alkalis (FM Approved) Size: 1092W X 457D X 1651HConstruction similar to the flammable liquids storage cabinets above but for storage of Acids and Corrosives with provisions for venting
Make: Justrite/Eagle
P5) VSDU 8 (Vertical Sliding Door Unit with glass shutter)
Size: 900 x 450 x 1830mm
• GlassDoor Model with dimensions 900mm (W) x 450mm (D) x 1830mm (H)• Construction and Material
1. It has a rigid knockdown construction2. Back, Sides and Door are made of 0.7mm high yield strength CRCA, rest are made of
0.8mm CRCA• Sliding Door Arrangement
1. Sliding Door with tophanging arrangement to prevent derailment2. Each door provided with 2 plastic rollers having steel ball bearings for smooth
movement of door and creation of minimal noise• Locking and Handle
1. Snap on type aesthetically appealing die cast 5 Lever Cam lock for safe locking2. Plastic Flush and recessed handle
• Shelving1. Heightwise Adjustable Shelf Mounting2. Uniformly distributed load capacity of shelf is 40kg maximum3. There are 4 nos. of adjustable Full Shelves
MMD, IIT BOMBAY Page no. 84 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
4. Box file A4size can be stored vertically on four shelves and clear space above fifth shelf is 220mm as shown in the image
• Top1. Metal Top
• Leveler1. Screwtype leveler with hexplastic base (add in unit height min. 8mm and additional
5mm max for adjustment)• Finish
1. Epoxy Polyester Powder coated to the thickness of 50 microns (+/ 10)
Q)WORKSURFACE and ACCESSORIES
It should be 19mm (+/ 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a Vgroove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. A representation the worktop edges is shown as in drawing.
MMD, IIT BOMBAY Page no. 85 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
Specification of Laboratory Fume hood
Super structure : All outer walls of the fume hood to be made of IS: 277 GI sheets the thickness of the sheets is 1.2 mm for all load bearing members and 0.8 mm for all cover panels. The fume hood to have a double wall construction and with inner wall made of 6 mm thick phenol based industrial laminate sheets. The back wall to have baffle arrangement made of 6 mm thick phenol based industrial laminate to ensure aerodynamic airflow for gases of various densities. The double wall construction to house all the service fittings of the fume hood with the connections to the top of the fume hood. The front fascia of the fume hood and the side walls of the fume hood to be openable to allow for the maintenance of the fume hoods in case of any service requirements without having to move the fume hood from its location. All fume hoods to have all side panels covered so that it can be moved and placed at any other location without any problems – No add on fume hoods with missing side panels allowed.
Sash frame : The sash frame to be made of Aluminum extrusion as per IS: 733 and the glass in the frame to be Toughened float glass as per IS: 2553 part 1. The sash frame to be operated with sprocket and chain mechanism the chain sprocket system to take a load of 700 kgs for a pair. Sash handle to be of Aluminum extrusion as per IS: 733. Sash handle ensures aerodynamic flow of air in to the fume hood.
Service doors : The fume hood to have super structure with a service door on the top to give access for maintenance of all the electrical and light fixtures etc. the Service door to be with polyamide hinges and to have a gas assisted lifts for easy door opening.
Air foil : Aerodynamic shaped airfoil to control vortex inside the fume hood. The airfoil to be made of 1.6 mm thick Aluminum powder coated as per 52000H1 of IS: 737.
Worktop : The fume hood work top to be made of jet black granite of 18 mm thick with 6 mm thick edge molding all around the worktop making it a water tight pan construction.
Cup sink: Polypropylene cup sink of approved make to be provided in the fume hood.
Apparatus Holding Grid: The grid to be made of SS 304 tubes dia 12.7 mm 1 mm thick with powder coating. The Grid to cover the entire width of the fume hood.
Electrical control panel: 1) In case the fume hood is connected to the blower then the electric control box on the fume hood to
be provided with Input of 3 phase, 415 V AC, 30 A. The electric box to have an overload relay for the motor, Circuit breaker in the event of short circuit and overload and phase failure detection for motor protection. Earthing point to be provided on the control box for additional safety.
2) In case the fume hood is not connected to the motor and is running on a cluster then the control panel to be provided with Input of 3 phase, 415 V AC, 30 A. Circuit breaker in the case of short
MMD, IIT BOMBAY Page no. 86 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
circuit and overload. Earthing point to be provided on the control box for additional safety.
Lights: The fume hood to be provided with energy efficient, maintenance free and environmental friendly LED lamps. The LED lamp to be of 15 W with glass diffuser to provide an average lux level of 600 Airflow monitor: The fume hood to be provided with a digital airflow monitor with a safe flow alarm indicator. The airflow monitor to be of TEL UK make.
Port for electrical cables: To stream line the power cords/Hose of the instruments from the fume hood a port to be provided on the side of the fume hood. The dia of the port to be 80 mm made of Polypropylene homo polymer H 110 MA.
Electrical Switch sockets: The switch sockets provide on the sides of the fume hood to be 3 module with 16 A sockets and 16 A tiny trip of approved make. Each side of the fume hood to have a maximum power capacity of 20 A, 3.5 KW. The fume hood to be internally wired and tested on the factory with FRLS wires of approved make.
Service Valves: Valves and faucets to be of approved make tubes used to be PVC braided hose of ½ inch OD. And for Vacuum SS braided flexible hose of ½ inch OD. The valves to be tested for working pressure of 125 PSI.
Ceiling Enclosure: The fume hood to be covered above the hood level to the false ceiling level with a ceiling enclosure. The enclosure is to be made of 1.2 mm thick GI sheet as per IS: 277. Powder Coating: All metal surfaces to be powder coated with pure epoxy powder coating of approved make with Dry film thickness of 70 – 80 Microns.
Fume hood understructure: The under structure of the fume hood to be of welded construction with removable back panel for maintenance access. The Storage to be made of 1.2 mm thick GI as per IS: 277. The unit to also have one shelf and hinge to be made of SS 304 of Knuckle barrel type. The shutter to be a sandwich design with 14 mm thick profeel insert for sound dampening. Handles to be Aluminium recess type.
Fume Hood understructure Chemical storage: The under structure of the fume hood to be of welded construction with removable back panel for maintenance access. The Storage to be made of 1.2 mm thick GI as per IS: 277. The unit to also have one shelf and hinge to be made of SS
MMD, IIT BOMBAY Page no. 87 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
304 of Knuckle barrel type. The shutter to be a sandwich design with 14 mm thick profeel insert for sound dampening. Handles to be Aluminium recess type. The cabinet to have a lining of 2 mm thick FRV coating. The shelves to be of 5 mm thick FRV. The interior of the cabinet to not have any exposed metal parts.
Centrifugal Blower – Silenthigh efficiency remote blower consisting of continuous rating motor and chemical resistant impellar. The blower should be designed to give a face velocity at safe working height as per the international safe velocity norms. (ANSI/AIHA Z9.5). The blower body should be polypropylene UV treated, high density and chemical (corrosion) resistant and mounted on a metallic stand.
Ducting – Rigid Ducting of PP (Polypropylene) + FRP (Fibre Reinforced Polyester) and flexible ducting with flanges, bends, damper transitions, clamps etc. Flexible joint should be provided in the ducting in order to avoid transmitting the blower vibrations to the hood. A weather proof rain cowl is provided at the outlet of blower.
MMD, IIT BOMBAY Page no. 88 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
LIST OF APPROVED MAKES
Steel TATA Steel, JINDAL SteelPowder Coating Kansai Nerolac, Berger Paints, Asian Paints ,
AkzonobleEmergency Equipment, Water Faucets and Gas Valves, Fume Hood Utility Fittings
Watersaver, Broen
Switches and Sockets, Data and LAN points Northwest, NorisysLocks Hettich, Hafele, Godrej, KalfDrawer Slides Hettich, Hafele, Godrej, KalfSink (PP Sink) KL Labs, Malaysia, Alloyplass, Premier
PolymersWorktop Jet Black GraniteStorages for Flammable items Justrite, AsecosBlowers Seat, Colasit, Almonard, PlastifierSpot Extractors Nederman, Fumex, Premier PolymersWires & Cables Polycab, Finolex
LAB FURNITURE :
SR. NO. ITEM DESCRIPTION IF ANY DEVIATION MENTION
A CFRAME SYSTEM
B HORIZONTAL MEMBERS
C COVER PANELS
D VERTICAL UPRIGHT
E ELECTRICAL BOOM
F TABLE MOUNTED ELECTRICAL TRUNCKING
G ELECTRICAL FITTINGS AND ACCESSORIES
H REAGENT SHELVES
I OVERHEAD CABINETS
J STORAGE UNITS
K ANTI VIBRATION TABLE
L SINKS AND ACCESSORIES
M GAS VALVE
N SPOT EXTRACTOR
MMD, IIT BOMBAY Page no. 89 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
O OTHER LAB ACCESSORIES
P CHEMICAL STORAGE CABINETS (WITHOUT EXHUST)
Q WORKSURFACE AND ACCESSORIES
R INSTALLATION
FUME HOOD :
SR. NO. ITEM DESCRIPTION IF ANY DEVIATION MENTION
A SUPER STRUCTURES
B UNDERSTRUCTURE
C AFA 1000/1 FOR FUMEHOOD
D COVER PANEL FOR FUMEHOOD
E ELECTRICALS
F APPARATUS GRID
G UTILITY SERVICE VALVES (FLEXIBLE TUBING)
H UTILITY SERVICE VALVES (SS TUBING)
I AUTOSASH
J UNDERSTRUCTURE FRAME
K BLOWERS
L DUCTING (PER SQ. FT.)
M INSTALLATION
MMD, IIT BOMBAY Page no. 90 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
SECTION 7
(A) PRICE BID FOR OFFICE FURNITURE
Sr. No.
Description of Item & Specification
Qty in Units
Unit Price
Excise/Custom Duty %
CST/VAT%
Octroi %
Other charges if any please specify details
Total Price
1. Office Chairs (1) 1 no.
2 Office Chair (2) 1 no.
3 Office Chair (3) 1 no.
4 Executive Chair (1) 1 no.
5 Executive Chair (2) 1 no.
6 Executive Visitor Without Wheels Chairs
1 no.
7 Visitor Chairs 1 no.
8 Visitor Chair Without Wheels 1 no.
9 Conference Chair 1 no.
10 Study Chair (1) 1 no.
11 Study Chair (2) 1 no.
12 Hostel Chair (1) 1 no.
13 Hostel Chair (2) 1 no.
14 Canteen Chair (1) 1 no.
15 Canteen Chair (2) 1 no.
16 Faculty Unit (1)
16A Faculty Table (Type 16A) 1 no.
16B Faculty Table (Type 16B) 1 no.
16C Faculty Table (Type 16C) 1 no.
16D Faculty Table (Type 16D) 1 no.
16E Faculty Table (Type 16E) 1 no.
16F Faculty Table (Type 16F) 1 no.
16G Faculty Table (Type 16G) 1 no.
MMD, IIT BOMBAY Page no. 91 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
16H Faculty Table (Type 16H) 1 no.
16 I Faculty Table (Type 16 I) 1 no.
16J Faculty Table (Type 16J) 1 no.
16K Faculty Table (Type 16K) 1 no.
16L Faculty Table (Type 16L) 1 no.
16M Faculty Table (Type 16M) 1 no.
16N Faculty Table (Type 16N) 1 no.
16O Faculty Table (Type 16O) 1 no.
17 Faculty Unit (2)
17A Faculty Table (Type 17A) 1 no.
17B Faculty Table (Type 17B) 1 no.
17C Faculty Table (Type 17C) 1 no.
17D Faculty Table (Type 17D) 1 no.
17E Faculty Table (Type 17E) 1 no.
17F Faculty Table (Type 17F) 1 no.
17G Faculty Table (Type 17G) 1 no.
17H Faculty Table (Type 17H) 1 no.
17 I Faculty Table (Type 17 I) 1 no.
17J Faculty Table (Type 17J) 1 no.
17K Faculty Table (Type 17K) 1 no.
17L Faculty Table (Type 17L) 1 no.
17M Faculty Table (Type 17M) 1 no.
17N Faculty Table (Type 17N) 1 no.
17 O Faculty Table (Type 17 O) 1 no.
17P Faculty Table (Type 17P) 1 no.
17Q Faculty Table (Type 17Q) 1 no.
18 Conference Table (1)
18A Conference Table (Type 18A) 1 no.
18B Conference Table (Type 18B) 1 no.
18C Conference Table (Type 18C) 1 no.
18D Conference Table (Type 18D) 1 no.
19 Conference Table (2) 1 no.
20 2 Drawer Filing Cabinet 1 no.
MMD, IIT BOMBAY Page no. 92 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
21 4 Drawer Filing Cabinet 1 no.
22 Cupboard Major with 4 Shelves
1 no.
23 Cupboard (Glass Door) 1 no.
24 Personal Locker Unit with individual lockers
1 no.
25 Study Table 1 no.
26 Single Bed (1) 1 no.
27 Single Bed (2) 1 no.
Place : VAT Registration No :
Date : TIN Registration No :
Signature :
Name :Office Address :Affix Rubber Stamp:
MMD, IIT BOMBAY Page no. 93 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
(B) PRICE BID FOR MODULAR / CUSTOMISED FURNITURE
Sr. No.
Description of Item & Specification
Qty in Units
Unit Price
Excise/Custom Duty %
CST/VAT%
Octroi %
Other charges if any please specify details
Total Price
1 Workstation (1)
1A Workstation Type No. (1A) 1 no.
1B Workstation Type No. (1B) 1 no.
1C Workstation Type No. (1C) 1 no.
1D Workstation Type No. (1D) 1 no.
1E Workstation Type No. (1E) 1 no.
2 Workstation (2)
2A Workstation Type No. (2A) 1 no.
2B Workstation Type No. (2B) 1 no.
2C Workstation Type No. (2C) 1 no.
3 Workstation (3)
3A Workstation Type No. (3A) 1 no.
3B Workstation Type No. (3B) 1 no.
3C Workstation Type No. (3C) 1 no.
4 Workstation (4)
4A Workstation Type No. (4A) 1 no.
4B Workstation Type No. (4B) 1 no.
4C Workstation Type No. (4C) 1 no.
4D Workstation Type No. (4D) 1 no.
4E Workstation Type No. (4E) 1 no.
5 Class Room Table
5A Class Room Table Type No. (5A)
1 no.
5B Class Room Table Type No. (5B)
1 no.
5C Class Room Table Type No. (5C)
1 no.
MMD, IIT BOMBAY Page no. 94 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
5D Class Room Table Type No. (5D)
1 no.
5E Class Room Table Type No. (5E)
1 no.
5F Class Room Table Type No. (5F)
1 no.
5G Class Room Table Type No. (5G)
1 no.
5H Class Room Table Type No. (5H)
1 no.
Place : VAT Registration No :
Date : TIN Registration No :
Signature :
Name :
Office Address :Affix Rubber Stamp:
MMD, IIT BOMBAY Page no. 95 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
(C) PRICE BID FOR LAB FURNITURE
Sr. No.
Description of Item & Specification
Qty in Units
Unit Price
Excise/Custom Duty %
CST/VAT%
Octroi %
Other charges if any please
specify details
Total Price
A CFRAME
A1 750 height CFrame
1 750 ht.CFrame assy. 595 mm Depth
1 no.
2 750 ht.CFrame assy. 670 mm Depth
1 no.
3 750 ht.CFrame assy. 745 mm Depth
1 no.
4 750 ht.CFrame assy. 820 mm Depth
1 no.
5 750 ht.CFrame assy. 895 mm Depth
1 no.
6 750 ht.Corner CFrame assy. 1 no.
A2 900 height CFrame
1 900 ht.CFrame assy. 595 mm Depth
1 no.
2 900 ht.CFrame assy. 670 mm Depth
1 no.
3 900 ht.CFrame assy. 745 mm Depth
1 no.
4 900 ht.CFrame assy. 820 mm Depth
1 no.
5 900 ht.CFrame assy. 895 mm Depth
1 no.
6 900 ht.Corner CFrame assy. 1 no.
B HORIZONTAL MEMBERS
MMD, IIT BOMBAY Page no. 96 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
B1 750 Ht. Horizontal members
1 600 module length horizontal members
1 no.
2 750 module length horizontal members
1 no.
3 900 module length horizontal members
1 no.
4 1050 module length horizontal members
1 no.
5 1200 module length horizontal members
1 no.
6 1350 module length horizontal members
1 no.
7 1500 module length horizontal members
1 no.
8 1650 module length horizontal members
1 no.
9 1800 module length horizontal members
1 no.
10 1460 end sink unit module length horizontal members
1 no.
11 1760 end sink unit module length horizontal members
1 no.
B2 900 Ht. Horizontal members
1 600 module length horizontal members
1 no.
2 750 module length horizontal members
1 no.
3 900 module length horizontal members
1 no.
4 1050 module length horizontal members
1 no.
5 1200 module length horizontal members
1 no.
6 1350 module length horizontal members
1 no.
7 1500 module length horizontal 1 no.
MMD, IIT BOMBAY Page no. 97 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
members
8 1650 module length horizontal members
1 no.
9 1800 module length horizontal members
1 no.
10 1460 end sink unit module length horizontal members
1 no.
11 1760 end sink unit module length horizontal members
1 no.
C COVER PANELS FOR C FRAMES
C1 750 working height cover panels
1 1540 depth island table end cover panel
1 no.
2 1840 depth island table end cover panel
1 no.
3 770 depth wall side end cover panel
1 no.
4 end sink unit side covr panel 1 no.
5 filler panel for end sink unit side
1 no.
6 920 depth wall side end cover panel
1 no.
C2 900 working height cover panels
1 1540 depth island table end cover panel
1 no.
2 1840 depth island table end cover panel
1 no.
3 770 depth wall side end cover panel
1 no.
4 end sink unit side covr panel 1 no.
5 filler panel for end sink unit side
1 no.
6 920 depth wall side end cover panel
1 no.
MMD, IIT BOMBAY Page no. 98 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
D VERTICAL UPRIGHTS
1 Master Upright 2400 mm Ht. (Service Dropper)
1 no.
2 1500 ht. upright 1 no.
3 1800 ht. upright 1 no.
4 2100 ht. upright 1 no.
E ELECTRICAL BOOM
1 600 module length (Cutout : 6 module)
1 no.
2 750 module length (Cutout : 6 module)
1 no.
3 900 module length (Cutout : 6 module+ 6 module)
1 no.
4 1050 module length (Cutout : 6 module+ 6 module)
1 no.
5 1200 module length (Cutout : 6 module+ 6 module)
1 no.
6 1350 module length (Cutout : 6 module+ 6 module)
1 no.
7 1500 module length (Cutout : 6 module+ 6 module)
1 no.
8 1650 module length (Cutout : 6 module+ 6 module)
1 no.
9 1800 module length (Cutout : 6 module+ 6 module)
1 no.
F TABLE MOUNTED ELECTRICAL TRUNCKING
1 600 module length (Cutouts : 6 module+ 6 module)
1 no.
2 750 module length (Cutout : 6 module)
1 no.
3 900 module length (Cutout : 6 module+ 6 module)
1 no.
4 1050 module length (Cutout : 6 module+ 6 module)
1 no.
5 1200 module length (Cutout : 6 module+ 6 module)
1 no.
MMD, IIT BOMBAY Page no. 99 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
6 1350 module length (Cutout : 6 module+ 6 module)
1 no.
7 1500 module length (Cutout : 6 module+ 6 module)
1 no.
8 1650 module length (Cutout : 6 module+ 6 module)
1 no.
9 1800 module length (Cutout : 6 module+ 6 module)
1 no.
G ELECTRICAL FITTINGS AND ACCESSORIES
1 1 Module Plate 1 no.
2 6 Module Plate 1 no.
3 16A, 1 way Switch 1 no.
4 6/16A, 6 pin shutter Socket 1 no.
5 32A, SP MCB 1 no.
6 Telephone Jack RJ11 (2 Points)
1 no.
7 Computer Data Transfer Socket With Shutter RJ45 CAT 5
1 no.
8 Blanking Plate 1 no.
9 5 pin, 32A Industrial Plug Cat. No. PS32AA5
1 no.
10 5 pin, 32A Industrial Socket: Cat. No. PS32BA5
1 no.
H REAGENT SHELVES
H1 Aluminum Extrusion Shelf with Glass
1 600 module length 1 no.
2 750 module length 1 no.
3 900 module length 1 no.
4 1050 module length 1 no.
5 1200 module length 1 no.
H2 FIXED TYPE REAGENT SHELF
1 Fixed type reagent shelf 600 L (Cutouts : 6 module+ 6 module (Total 2 Cutouts Only)
1 no.
MMD, IIT BOMBAY Page no. 100 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
2 Fixed type reagent shelf 750 L (Cutouts : 6 module+ 6 module (Total 2 Cutouts Only)
1 no.
3 Fixed type reagent shelf 900 L (Cutouts : 6 module+ 6 module (Total 2 Cutouts Only)
1 no.
4 Fixed type reagent shelf 1050 L (Cutouts : 6 module+ 6 module (Total 2 Cutouts Only)
1 no.
5 Fixed type reagent shelf 1200 L (Cutouts : 6 module+ 6 module (Total 2 Cutouts Only)
1 no.
I OVERHEAD CABINETS
1 Overhead Cabinet: 450W 635H 1 Shutter
1 no.
2 Overhead Cabinet: 600W 635H 2 Shutters
1 no.
3 Overhead Cabinet: 750W 635H 2 Shutters
1 no.
4 Overhead Cabinet: Corner 635H 1 Shutter
1 no.
J STORAGE UNITS
J1 FLOOR MOUNTED WITH METAL SKIRTING TYPE (RecessType Handles)
1 Floor Mounted Welded Cabinet 1 Shutter 445W875H
1 no.
2 Floor Mounted Welded Cabinet 1 Shutter 1 Drawer 450W875H
1 no.
3 Floor Mounted Welded Cabinet 2 Shutters 1 Drawer 600W875H
1 no.
4 Floor Mounted Welded Cabinet 2 Shutters 1 Drawer 900W875H
1 no.
5 Floor Mounted Welded Sink Cabinet 2 Shutters 600W875H
1 no.
6 Floor Mounted Welded Corner Cabinet 1 Shutter 875H
1 no.
MMD, IIT BOMBAY Page no. 101 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
7 Floor Mounted Welded Corner Sink Cabinet 1 Shutter 875H
1 no.
8 Floor Mounted Welded Cabinet 1 Shutter 1 Drawer 450W725H
1 no.
9 Floor Mounted Welded Cabinet 2 Shutters 1 Drawer 600W725H
1 no.
10 Floor Mounted Welded Cabinet 2 Shutters 1 Drawer 750W725H
1 no.
11 Floor Mounted Welded Cabinet 2 Shutters 1 Drawer 750W725H
1 no.
12 Floor Mounted Welded Cabinet 2 Shutters 1 Drawer 900W725H
1 no.
13 Floor Mounted Welded Corner Cabinet 1 Shutter 725H
1 no.
J2 WFUHANGING TYPE (RecessType Handles)
1 Hanging Storage Unit 1 Shutter 1 Drawer 450W 725H
1 no.
2 Hanging Storage Unit 2 Shutters 1 Drawer 600W 725H
1 no.
3 Hanging Storage Unit 2 Shutters 1 Drawer 750W 725H
1 no.
4 Hanging Storage Unit 2 Shutters 1 Drawer 900W 725H
1 no.
5 Hanging Storage Corner Unit 1 Shutter 725H
1 no.
6 Hanging Storage Unit 1 Shutter 445W 900H
1 no.
7 Hanging Storage Unit 1 Shutter 1 Drawer 450W 900H
1 no.
8 Hanging Storage Unit 2 Shutters 1 Drawer 600W 900H
1 no.
9 Hanging Storage Unit 2 Shutters 1 Drawer 750W 900H
1 no.
MMD, IIT BOMBAY Page no. 102 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
10 Hanging Storage Unit 2 Shutters 1 Drawer 900W 900H
1 no.
11 Hanging Storage Sink Unit 2 Shutters 1 Drawer 600W 900H
1 no.
12 Hanging Storage Corner Unit 1 Shutter 900H
1 no.
13 Hanging Storage Corner Sink Unit 1 Shutter 900H
1 no.
J3 CASTOR BASED WFMMOBILE TYPE (RecessType Handles)
1 Mobile Storage 450 W 1 Shutter 1 Drawer 7H
1 no.
2 Mobile Storage 600 W 2 Shutters 1 Drawer 7H
1 no.
3 Mobile Storage 450 W 1 Shutter 1 Drawer 9H
1 no.
4 Mobile Storage 600 W 2 Shutters 1 Drawer 9H
1 no.
J4 LEGSPACE AND ACCESSORIES (WELDED FLOOR MOUNTED RANGE)
1 Leg Space with Slim Drawer 580W875H
1 no.
2 Leg Space with Slim Drawer 730W875H
1 no.
3 Leg Space Plain 580W875H 1 no.
4 Leg Space Plain 730W875H 1 no.
5 Leg Space with Key Board Tray 730W875H
1 no.
6 Modesty Panels 1 no.
7 Back Support Brackets 1 no.
8 PVC Skirting 90mm Ht Black Color + Glue
1 no.
K ANTI VIBRATION TABLE
1 AVT 2 Frame : 900 x 600 x 900mm
1 no.
2 AVT 2 : GRANITE SLAB 1 no.
MMD, IIT BOMBAY Page no. 103 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
3 AVT 2 : KADAPPA SLAB 1 no.
L ACCESSORIES
L1 SINKS AND ACCESSORIES
1 SS Sink 1 no.
2 PP Dropin Sink Size : 560 mm (W) x 355 mm (D)
1 no.
3 Cup Sink Oval Drip Cup 1 no.
4 AntiSiphon bottle trap 1 no.
5 Flexible/ F ; Connector Size : 38mm x Length = 1m
1 no.
6 SS Pegboard Size : 550 x 420 x 55, 25 Pegs
1 no.
7 3 Way Faucet Bench mounted 3 way water fittings with 8" swing gooseneck
1 no.
8 Single Water Faucet Deck mounted, 8" swing gooseneck
1 no.
9 Twoway Deck Mounted Eye Wash
1 no.
10 Floor Mounted PVC emergency safety shower with eyewash
1 no.
M GAS VALVE
1Singleway Gas Valve for Non Burning Gases
1 no.
2 Twoway Gas Valve for Non Burning Gases
1 no.
3 Singleway Gas Valve for Burning Gases
1 no.
4 Twoway Gas Valve for Burning Gases
1 no.
N SPOT EXTRACTORCeiling/ Wall MountedModel No: FX75
1 Arm FX75 1500L Connection up
1 no.
2 Bracket for Spot Fume Extractor
1 no.
MMD, IIT BOMBAY Page no. 104 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
3 Multipurpose Hood 380 x 460 1 no.
4 Extension Profile 1100L 1 no.
5 Reducer 75 80 FR Spot Fume 1 no.
O OTHER LAB ACCESSORIEES
1 Plastic KBPT 1 no.
2 REV STOOL MCH HT ADJ + BACK HI BASE
1 no.
P CHEMICAL STORAGE CABINETS [Without Exhaust]
1 MS Chemical Storage Cabinet [with top cover plate] Size:1000 x 486 x 1800mm : 1.2mm thk.
1 no.
2 Full PP Cabinet for Acid Storage Dimensions: 1000mm W x 486mm D x 1500mm H
1 no.
3 Cabinet for Flammable liquid storages with 10 mins fire rating (FM Approved) Size: 1092W X 457D X 1651H
1 no.
4 Cabinet for acids and alkalis (FM Approved) Size: 1092W X 457D X 1651H
1 no.
5 VSDU 8 (Vertical Sliding Door Unit with glass shutter) Size: 900 x 450 x 1830mm
1 no.
Q WORKSURFACE and ACCESSORIES
1 Jet Black Granite (Sq.mt.) 20 (±2) mm thk.
1 no.
2 Silicon Sealant Black 1 no.
3 Masking Tape 1 no.
4 Neoprene Strip (Running Meter) (30mm wide & 6 mm thick)
1 no.
5 SR998 Glue for Neoprene Mat. (Litres)
1 no.
6 MDF with Laminate, (Nos.) 25mm [1200mm x 2400mm]
1 no.
MMD, IIT BOMBAY Page no. 105 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
7 Trespa Top Lab Plus(Sq mt) 16 mm thk.
1 no.
R INSTALLATION %
Place : VAT Registration No :
Date : TIN Registration No :
Signature :
Name :
Office Address :Affix Rubber Stamp:
MMD, IIT BOMBAY Page no. 106 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
(C1) PRICE BID FOR FUME HOOD
Sr. No.
Description of Item & Specification
Qty in Units
Unit Price
Excise/Custom Duty %
CST/VAT%
Octroi %
Other charges if any please specify details
Total Price
A SUPER STRUCTURES
4 FEET BENCHTOP LCV FUME HOOD WITH LED LIGHT (WITHOUT ANY ACCESSORIES)
1 no.
5 FEET BENCHTOP LCV FUME HOOD WITH LED LIGHT (WITHOUT ANY ACCESSORIES)
1 no.
6 FEET BENCHTOP LCV FUME HOOD WITH LED LIGHT (WITHOUT ANY ACCESSORIES)
1 no.
7 FEET BENCHTOP LCV FUME HOOD WITH LED LIGHT (WITHOUT ANY ACCESSORIES)
1 no.
8 FEET BENCHTOP LCV FUME HOOD WITH LED LIGHT (WITHOUT ANY ACCESSORIES)
1 no.
B UNDERSTRUCTURE
B1 FIXED TYPE APPARATUS STORAGE CABINET FOR BENCH TOP FUME HOOD
600 WIDTH FIXED TYPE APPARATUS STORAGE CABINET FOR BENCH TOP FUME HOOD
1 no.
750 WIDTH FIXED TYPE APPARATUS STORAGE
1 no.
MMD, IIT BOMBAY Page no. 107 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
CABINET FOR BENCH TOP FUME HOOD
900 WIDTH FIXED TYPE APPARATUS STORAGE CABINET FOR BENCH TOP FUME HOOD
1 no.
B2 MOBILE APPARATUS STORAGE CABINET FOR BENCH TOP FUME HOOD
1 540W MOBILE APPARATUS STORAGE CABINET FOR BENCH TOP FUME HOOD WITH FRAME BASED UNDERSTRUCTURE
1 no.
2 700W MOBILE APPARATUS STORAGE CABINET FOR BENCH TOP FUME HOOD WITH FRAME BASED UNDERSTRUCTURE
1 no.
3 840W MOBILE APPARATUS STORAGE CABINET FOR BENCH TOP FUME HOOD WITH FRAME BASED UNDERSTRUCTURE
1 no.
B3 FIXED STORAGE FOR FLAMMABLE LIQUIDS (FM APPROVED)
591 W X 889H X 457D 1 no.
889 W X 889H X 559 D 1 no.
B4 FULL PP ACID STORAGE CABINET
1 540 W X 630H X 530D 1 no.
2 700 W X 630H X 530D 1 no.
3 840 W X 630H X 530D 1 no.
C AFA 1000/1 FOR FUMEHOOD
1 no.
D COVER PANEL FOR FUMEHOOD
1 no.
E ELECTRICALS
1 6 MODULE SWITCH SOCKET 1 no.
MMD, IIT BOMBAY Page no. 108 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
WITH TINY TRIP 16A
2 INDUSTRIAL SWITCH SOCKET 20A
1 no.
E APPARATUS GRID
4 FEET BENCHTOP FUMEHOOD
1 no.
5 FEET BENCHTOP FUMEHOOD
1 no.
6 FEET BENCHTOP FUMEHOOD
1 no.
7 FEET BENCHTOP FUMEHOOD
1 no.
8 FEET BENCHTOP FUMEHOOD
1 no.
G UTILITY SERVICE VALVES (FLEXIBLE TUBING)
1 no.
H UTILITY SERVICE VALVES (SS TUBING)
1 no.
I AUTOSASH 1 no.
J UNDERSTRUCTURE FRAME
1 FRAME BASED UNDERSTRUCTURE FOR 4 FEET BENCH TOP FUMEHOOD WITH NO CUTOUT ON TRUNKING
1 no.
2 FRAME BASED UNDERSTRUCTURE FOR 5 FEET BENCH TOP FUMEHOOD WITH NO CUTOUT ON TRUNKING
1 no.
3 FRAME BASED UNDERSTRUCTURE FOR 6 FEET BENCH TOP FUMEHOOD WITH NO CUTOUT ON TRUNKING
1 no.
4 FRAME BASED UNDERSTRUCTURE FOR 7 FEET BENCH TOP FUMEHOOD WITH NO CUTOUT ON TRUNKING
1 no.
MMD, IIT BOMBAY Page no. 109 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
5 FRAME BASED UNDERSTRUCTURE FOR 8 FEET BENCH TOP FUMEHOOD WITH NO CUTOUT ON TRUNKING
1 no.
K BLOWERS
1 PP + FRP lined Blower with FRPvinylester impeller and a motor, 1100CFM, 1400RPM, 0.75H.P. KEC/CGL Make Motor, 50mm W.G.
1 no.
2 PP + FRP lined Blower with FRPvinylester impeller and a motor, 1000CFM, 1400RPM, 0.75H.P. KEC/CGL Make Motor, 50mm W.G.
1 no.
3 PP + FRP lined Blower with FRPvinylester impeller and a motor, 1100CFM, 1400RPM, 1.5H.P. KEC/CGL Make Motor, 60mm W.G.
1 no.
4 PP + FRP lined Blower with FRPvinylester impeller and a motor, 1100CFM, 1400RPM, 2H.P. KEC/CGL Make Motor, 60mm W.G.
1 no.
L DUCTING (PER SQ. FT.) (PER SQ. FT.)
M INSTALATION %
Place : VAT Registration No :
Date : TIN Registration No :
Signature :
Name :
Office Address :Affix Rubber Stamp:
MMD, IIT BOMBAY Page no. 110 of 111
RFP for Empanelment & Annual Rate Contract of suppliers for Furniture & Fixtures
SECTION 8 CHECKLIST
The following items must be checked before the Bid is submitted:
1. Envelope “1”
a) Demand Draft for Rs. 500/ (Rs. Five Hundred only) towards cost of Bid document
b) Demand Draft for Rs. 5 lakh/ (Rs. Five lakh only) towards Earnest Money Deposit.
c) Eligibility Criteria Responses (each pages duly sealed and signed by the authorized
signatory)
d) Copy of this RFP document duly sealed and signed by the authorized signatory on every
pages.
e) Annexure A1 : Undertaking Submission of Offer
Annexure A2 : Declaration Regarding Clean Track by Bidder
Annexure A3 : Declaration for Acceptance of RFP Terms and Conditions
Annexure A4 : Client Experience Details
Annexure A5 : Declaration Of Annual Turnover And Income Tax Return
Annexure A6 : Bidder's Information
2. Envelope “2”
a) Price Bids
Your quotation must be submitted in two envelopes Technical Bid (Envelope 1 ) and Price Bid
(Envelope 2 ) superscribing on both the envelopes the Tender No. and the due date and both these
sealed covers are to be put in a bigger cover which should also be sealed and duly superscribed with our
Tender No. & Due Date.
MMD, IIT BOMBAY Page no. 111 of 111