energy saving motors ecm ip65-ip66 - lns ecm 2012.pdfpromote energy saving, as well as a drastic...
TRANSCRIPT
Our contribution to energy saving and CO2 emissions reduction
2
Nowadays, the need toadopt effective actions topromote energy saving, as well as a drastic reductionin CO2 emissions into the atmosphere, is universallyrecognised.In Europe, there are in factseveral million of sub-fractional horsepowerelectric motors used both in domestic appliances, or in air-conditioning and refrigerators. For the latter,especially for the ventilationof refrigerated display cases,sub-fractional HP motors with extremely low efficiencyhave always been used. For example, approximately8 Watts of shaft output powerare needed to operate a 230 mm diameter fan blade,which can be obtained fromthe following types of motor:
Shaded poles: input power ~ 36 Wattefficiency ~ 18%
Electronically commutated: input power ~ 12 Wattefficiency ~ 65%
The importance of choosinga high-efficiency motor is evident from considering a single supermarket with approximately 200 m of refrigerated display unitsinstalled, for an estimatedtotal of 200 fan motors.
Considering an averageenergy cost of 0.11 Euro per kWh and CO2emissions of 0.6 kg per kWhconsumed, we can calculate that if the same supermarketused “electronic control”motors instead of the equivalent “shaded pole”models, 68,500 kWh could be saved in one year,equivalent to approximately7,500 Euro and a reductionin CO2 emissions of 41 tonnes.
Elettricity cost vs purchase motors costin 2 years of use
3
The sensible energy savingwidely compensates the greater cost of high-efficiency motors, withpayback in just few months: in fact, in the lifetime overallcost of a shaded-polemotor, energy consumptionrepresents almost 97-98%,while its purchase costsonly 2-3%.
Moreover, reduced CO2emissions is a topic of great interest in relationto the maximum quotasassigned to each countryand the related “carbontrading” that regulates the “emission credits” marketbetween virtuous users andless-virtuous ones.
Within this context, thanksto over 800,000 high-efficiency ECM motorsalready supplied to themarket, ELCO has contributed to a reductionin environmental emissionsof an estimated 116,000 tonnes of CO2per year.
To confirm the high-efficiency and consequentlythe cost advantage of ECM motors, a two-monthstest was carried out byindependent consultants at a large foodstore supermarket located inTortona (Northen Italy), by monitoring a specificarea of refrigerated display cases coveringapproximately 200 fanmotors. Energy consumption wasmonitored by initiallyrecording the usage of the traditional shaded polemotors and then replacingthem with ELCO’s ECMmodels.Tests results showed a saving of 142,423 kWhagainst a Total EnergyConsumption of 614,466kWh; the equivalent of approximately 85 tonnes of CO2.
Similar tests were carried outin some European supermarkets, where todayonly ELCO motors are used.The results have not only confirmed large savings, but also more uniform airflow thanks to the greatertorque of ECM motors.
The advantages with towards the “shaded pole”solution are:
• High efficiency 63÷68%
• Maximum moisture protection with the new IP65-IP66 versions
• Reduced depth comparedto the standard N serie Shaded Pole motors
• Drop in replacement with the standard N series and possibility to use all standard accessories
Simulation of a management cost over time of refrigerated MT and LT on Hypermarket with 400 motors
General specifications
ELCO SpA has developedand patented a new range of high-efficiency sub-fractional horse powerelectronically commutatedmotors - the ECM series.This new generation of motors is specificallydesigned to satisfy the growing market demands of“energy saving”, granting first-rate results in terms of efficiency and life expectancy.
The motor, totally enclosed in a thermoplastic housing,contributes to limiting external heat emission, whichresults in a particularly coolmotor body during operationand hence generate a furtherenergy savings.Thanks to a special, permanent lubrication systemand based on laboratorytests, the life expectancy isapproximately 30,000 hoursfor the Standard version and 60,000 hours for the Long Life version.
The ECM series is currentlyavailable in two single-speedversions, to be selectedaccording to power requirements.
4
Construction specificationsCertifications
IP65 moulded cable grommet IP66 cable strain relief IP66 with rear mounting
Type
StandardLong-LifeLong-Life
ProtectionRating
IP65IP65IP66
Bearing
Sleeve-bearingsBall-bearingsBall-bearings
5
Certifications
All products are designed and manufactured according to European regulations CENELEC EN 60335-1, electromagnetic compatibilityEN 61000-3-2 +A1/A2, EN55014-1 and CE marked.
All components are UL compliant.
UL XEIT listed versions areavailable.
* > 55°C upon request ** Approval pending
Technical data
100V / 50÷60HZ • 115-127V / 50÷60Hz • 230-240V / 50÷60Hz1450 • 1550 • 18501400 • 1600 • 1850
Working temperatureInsulation classProtection ratingVoltageRPM at 115-127VRPM at 230-240VIN powerStandards
Approvals
SupportsLife expectancy at 20°C
-40°C ÷ +55°C*B
CENELEC EN 60335-1 • EN 61000-3-2 + A1/A2 • EN 55014-1
IP65 IP65-IP66
ECMStandard
ECMLong Life
** **
30,000 hours 60,000 hoursSleeve-bearings Ball-bearings
9÷14W 9÷14W • 20÷25W
6
Interchangeability:
The ECM motor was alsodesigned to comply with the same principle of standardization that ELCOdeveloped for the N-seriesmotors.
In fact, ELCO’s “energy saving” motors are,drop-in replacements of the traditional shaded poleones, and use all the sameaccessories, such as brackets, fans, rings andguards, with no extra work- or hidden costs, to the full benefit of rapidity andconvenience.
Applications The ECM series motors may be universally applied, but are particularly suited to the refrigeration and ventilation industry,especially for refrigerateddisplay cases, freezers,drink dispensers and smallcondensers; they can becoupled with various typesof fan blades, particularlyaxial fans with diameters up to 300 mm.
N Fan
ECM Fan
7
Construction differences Product description:
The ECM IP65 and IP66Series is a new product,derived from the well-knownrange of energy-savingmotors and designed foroperation in environmentswith high humidity or moisture.
The IP65 version comes with an O-ring to seal therear plastic end-shield to themotor housing and mouldedcable grommet, sleeve or ball-bearings and a newfan profile integrated with the internal watherprooflabyrinth.While in the IP66 version,the motor has a double-sided rubber sealedball-bearings and cable exitfitted with an IP68 strainrelief.
The electronic control unit isprovided with various safetyfeatures:
• Overload control function, which switches the motor to standby mode if an external mechanical actioncauses the speed to drop below a preset level.
• Locked rotor control function, which switches the motor to standby modeafter twenty restart attempts, in case of fan blocked by icing or other reasons.
• Auto-reset function, which allows the microprocessor to reset and restart the control functions, in cases of electrical interference or power supply fluctuations.
• Self-diagnostics function during switch-on and switch-off. In cases of ON/OFFalternative use, each cycles should be at least 20 seconds apart.
• Power shut-down function in cases of microprocessorfailure.
IP65 Standard
IP66 Long Life
8
Overall dimensions
With integrated fan
With Aluminium/Plastic fan
Spacers to adjust the X distance
10
Mountings
Comparison of overall dimensions with bracket
ECM with aluminium or plastic fan with bracket
ECM with integrated fan and bracket
11
Motor
ECM 12W
ECM 20W
Fan
Ø 154 19°Ø 172 28°Ø 200 28°Ø 200 34°Ø 230 19°Ø 230 25°Ø 230 31°Ø 254 22°
Plasticsupport
ABBCBCCB
Y
4460637757707065
X
9296991029395105111
Plastic support Cod. 1-072-1251
Plastic support Cod. 1-072-1279
Plastic support Cod. 1-072-1280
12
Different solution of using
1Aluminium/PlasticFan with Rear Fixing
2Aluminium/PlasticFan with Support Fixing
3Aluminium/PlasticFan with Ring andSpacers
4Integrated Fan with Rear Fixing
5Integrated Fan with Ring
13
15419°22°25°28°31°34°19°22°25°28°31°34°
Type
A
AO
17219°22°25°28°31°34°19°22°25°28°31°34°
20019°22°25°28°31°34°19°22°25°28°31°34°
23019°22°25°28°31°34°19°22°25°28°31°34°
25419°22°25°28°31°
19°22°25°28°31°
30019°
19°
275
22°25°
25°
Fan Ø
140
28°
28°
Type
VEA
VEP
154
28°
19°
172
31°
200
28°
34°
31°
222
31°
25422°
28°
19°25°
230
25°28°31°
Fan Ø
15419°
Type
VIA
172
28°
200
28°
34°
23019°
25°
31°
254
22°
Fan Ø
Integrated plastic fan
Plastic fan with fan hub
Aluminium fan with fan hub and silencer
Fans for ECM motors
ECM 12W 1400 Rpm ECM 20W 1400 Rpm
14
ECM_H The consolidated experience, result of morethan 10 years of studies,analysis, research and production of ECM motor,sold world wide, and thecontinuous demand of higher performances, has been the basic premiseto develop a new version ofelectronically commutatedmotor that can satisfy themarket requests.
The new solution covers a wider range of aeraulicperformances with smallerdimensions, keeping undercontrol the motor efficiency.
Compared to the actualone, the motor presentsthe following features:
• Better efficiency• Wider range
of performances• Motor speed
up to 2700 rpm• Better exploitation
of electronic power and control
• Several kinds of hardwareand software protections
Technical data:
• 230V - 50Hz; 115-127V 50/60Hz motor
• Protection rating IP65, IP66
• Rotation speed: 1500-1600-1850-2200 rpm
• Working temperature: -40°C +55°C
• Protection by hardware and software
• Protection against electromagnetic disturbance in accordance with EMC
• Standard EN60335-1; EN61000-3-2 +A1/A2; EN55014-1
• Sleeve or ball bearings• Totally made of
thermoplastic material with double insulation
As the actual one, this new version is totallyinterchangeable with shaded pole motors andmainly used for refrigerating appliances.
154172200230254300
Fan 1600 RPM 1850 RPM 2200 RPM
19° 22° 25° 28° 31° 34° 19° 22° 25° 28° 31° 34° 19° 22° 25° 28° 31° 34°αØ /
Motors ECM_HMatching motor-fan
ECM_H 12-15 ECM_H 20-25
15
15419°22°25°28°31°34°19°22°25°28°31°34°
Type
A
AO
17219°22°25°28°31°34°19°22°25°28°31°34°
20019°22°25°28°31°34°19°22°25°28°31°34°
23019°22°25°28°31°34°19°22°25°28°31°34°
25419°22°25°28°31°
19°22°25°28°31°
30019°22°
19°22°
275
22°25°
25°
Fan Ø
140
28°
28°
Type
VEA
VEP
154
28°
19°
172
31°
200
28°
34°
31°
222
31°
25422°
28°
19°25°
230
25°28°31°
Fan Ø
15419°
Type
VIA
172
28°
200
28°
34°
23019°
25°
31°
254
22°
Fan Ø
Integrated plastic fan
Plastic fan with fan hub
Aluminium fan with fan hub and silencer
Fans for ECM_H motors
ECM_H 12W 1500 Rpm ECM_H 20W 1500 Rpm
Stu
dio
Bon
aE
CM
02.
10 -
Prin
ted
in It
aly
ELCO S.p.A.Via Marconi, 120065 INZAGO Milano - ItaliaPhone +39 02 95319.1 - Fax +39 02 95310138www.elco-spa.com - E-mail: [email protected]
ELCO MOTORES ESPAÑA SACarrer del Fusters s/n. - Pol. Ind. Les ValletesE-46.192 MONSERRAT - Valencia - EspañaPhone +34 96 2987117 - Fax +34 96 2987099E-mail: [email protected]
ELCO MOTORS INC.275 Liberte - CANDIAC QC J5R 3X8 - CanadaPhone +1 450 633 1515 - Fax +1 450 633 0851E-mail: [email protected]
ELCO MOTORES DE MEXICO SRL DE C.V.Calle Pirineos 515 - A Bodega N° 7Col. Ciudad Industrial Benito Juárez - Microparque Industrial Santiago 1C.P. 76120 Querétaro - Qro. MéxicoPhone +52 (442) 217 6062 - 217 6515 - Fax +52 (442) 217 6218E-mail: [email protected] - www.elco.com.mx
ELCO DO BRASIL LTDAAvenida Armando De Andrade, 54906754-210 - TABOÃO DA SERRA - SP - BrasilPhone (005511) 47019337 / 47019650 / 47878029 - Fax (005511) 47873106E-mail: [email protected]
ELCO MOTORS RUSSIA BRANCHStachek Prospect Building 47, litera A, Office 249198097 SAINT PETERSBURGPhone + 7 812 3349961 - Fax + 7 812 3349960E-mail: [email protected]
ELCO MOTORS AND FANS PTY LTD84 Northgate Drive THOMASTOWN VIC 3074 - AustraliaPhone +61 3 9464 2066 - Fax +61 3 9464 2077E-mail: [email protected]
ELCO MOTORS ASIA PTE LTD22 Kallang Avenue #07-06 - Hong Aik Industrial BuildingSINGAPORE 339413Phone +65 6298 9169 - Fax +65 6291 6520E-mail: [email protected]
ELCO MOTORS LIMITED FZCOP.O. Box 18358RoundAbout 8, Warehouse # DB01 - Jebel Ali Free Zone AreaDubai, U.A.EPhone + 971- 4- 8833392 - Fax + 971- 4- 8833390E-mail: [email protected]
ELCO CHINA LIMITEDHONG KONGDONGGUAN HENGLI ELCO CHINA MOTOR FACTORYXincheng Industrial Zone, Hengli, Guangdong Province, PRCPhone +86 769 3727378 - Fax +86 769 3727379E-mail: [email protected]
ELCO DIRECT LIMITEDBardney Airfield, Henry Lane, Bardney, Lincolnshire, LN3 5TP - U.K.Phone +44 1526 399711 - Fax +44 1526 399722E-mail: [email protected] - www.elco-motors.co.uk