enerpia heating film is the most advanced far-infrared planar heating element made of insulated and...
TRANSCRIPT
ENERPIA heating film is the most advanced far-infrared planar heating element made of insulated and flame-retardant base film applied with carbon heating element, thin-coated with active carbon, a absorbent for contaminants and laminated with PET film after making electrodes with copper bus bar. Unlike a normal heater, the carbon heating element applied all over the film emits far infrared radiant heat good for the health uniformly so that you can feel warmth like sunlight. Since the exterior material for film heater is a special polyester fabrics with a special waterproofing treatment not to contact the air, it is a future-oriented heater for wall, ceiling or floor heating which can be used almost semi-permanently. The performance of heating film depends on dispersion technology of nano particles by adhesion and resistance of carbon particles, silver particles and others.
Product Information of ENERPIA Heating Film
What is heating film, a planar heating element?
The planar heating element emits a radiant heat generated from electric energy conducted and absorbed by wide surface of thin film itself; i.e. a directly and momentarily transferred heating method without process of convective or conductive heat transfer, so it has many advantages such as no loss of heat, time not required for maintaining heating, desirable temperature obtainable through a digital temperature controller, no problem in heating except the damaged part if a part of heating film damaged, simplicity in installation, low load on the building and easiness in maintenance.
DAEWOO ENERTEC,
INC1/10
Structure OF ENERPIA Heating film
ENERPIA Heating Film is produced by accurate (under 1 micron) printing technology by coating carbon on PET film to radiate heat. The film is so strong that you can not cut it without scissors because the material was heat-treated over 150.
Structure
SafenessSteady temperature range and resistance variation
- Coating high density carbon particle
- Cutting edge doping technology for
uniformly printed surface
-Continuous development of special equipment
for heating film
- World class film with the character of
insulation and anti-flame
- Preventing spark on carbon surface by
specialized design - Special waterproof treatment - Laminated insulation film
DAEWOO ENERTEC, INC
2/10
Economical Heating - Lower cost by 30% than electric heat, 60% and more than oil boiler - Reduction of construction cost because of installation available within very short period - Energy saving because of sectional heating available - Adoption of automatic control (centralized control) system available
Radiant heating by far infrared rays - Rapid heating available - Radiant heating by far infrared rays makes room warm evenly without variation in temperature.. - Comfortable heating effect in comparatively low room temperature comparing with convective
type of heating
Simple installation and workability - Simple installation comparing with wet-mortar method. - Construction finished by installation between flooring material and insulations
Excellent durability - Usable semi-permanently - Simple in structure with little trouble
Heating method without combustion - Flameless heating method without generation of carbon monoxide, dust and combustion noise
Quiet and clean heating - Emitting plenty of far infrared rays and anions due to heating by carbon Far infrared ray / Anion :
Remove odors in the room, Good for human body, Create pleasant room air.
Effect of ENERPIA Heating film
DAEWOO ENERTEC,
INC3/10
Components and Principle of ENERPIA Heating Film
Components of Film Principle of Heating
PowerPower Copper Bus BarCopper Bus Bar Silver Bus BarSilver Bus Bar Carbon BlackCarbon Black
Generating heat by Generating heat by Electric resistance Electric resistance ΩΩ of carbon black itself applied on film (Center(Center Outside)Outside)
PartFunctio
nMaterial
Thickness
Control criteria at
manufacture
Insulation part
Base Film
PET125,188,250,350 Insulation and
flame-retardancy
Laminate Film
75
Adhesive
General heating
EVA 75 AdhesionThermal
resistanceHigh heat
EEA 75
Heating part
Carbon Doping
Carbon
Maintaining uniform
resistanceUniform printed surface
Electric conductio
n part
Copper bus bar
Copper 0.05mmElectric
conductivity
Silver bus bar
Silver
Conductivity
Adhesion
Dispersion
Installation diagram
Sensor1
Power
Thermostat
Sensor2
DAEWOO ENERTEC,
INC4/10
1. Carbon Paste, Heating part of ENERPIA HEATING FILM Carbon Black is a material obtained from carbon © like diamond as a main ingredient
and applied to automobile, ink or cosmetics. It is called carbon fiber to do heat treatment at 1,000-3,000 and graphite fiber to do heat treatment at more than 2,500 through manufacturing process. Graphite is widely used as a material for electric heating
element because of its high resistance to heat, its low coefficient of resistance and excellent
thermal conductivity and electrical conductivity.
Depending on mixing ratio of carbon and graphite in carbon strip, the part of heat generation
in heating, adhesion, resistance, etc can be adjusted. (It is to use properties of roun molecular structure of carbon and tabular structure of graphite.)
Characteristic of component of ENERPIA heating film (Ⅰ)
DAEWOO ENERTEC,
INC5/10
2. Silver Paste, Conduction part of ENERPIA FILM Heater
Silver paste, a conductive pasting material, is a low temperature type of conductive paste applied to planar heating element, which has excellent property for screen printing, high conductivity, excellent flexibility and excellent adhesion to P.E.T with Laminex. Test of resistance results in less than 0.1Ω.
Characteristic of component of ENERPIA Heating film (Ⅱ)
If resistance of silver paste, the planar heating element, is high, it may cause sparks and problem in safety. The lower resistance of conductor , the higher electrical efficiency.
3. P.E.T (polyethylene terephthalate) material for ENERPIA FILM Heater
P.E.T Polyester (Polyethylene terephthalate)
Characteristics of P.E.T Film • Excellent electric or electrothermal wire widely used as an electric insulation for power
generator, transformer, etc. Applied to heat sensitive areas such as film, coating, etc because of its low thermal
shrinkage (Shrinkage rate +/-2% at placement for 20 minutes at 150) • High strength and elasticity • Excellent durability against chemical reaction • UV-protective effect • Little ingredients hazardous to environment at incineration
Required property of PET for heating film : Adhesion, Insulation and flame-retardancy, No shrinkage
DAEWOO ENERTEC,
INC6/10
4. BASE FILM for electric insulation of ENERPIA FILM Heater
Characteristic of component of ENERPIA Heating Film (Ⅲ)
Film as a heating material must be applied with a material for electric and electronic use. Film material for ENERPIA FILM HEATER is a product with high turbidity excellent in
insulation.
ItemApplication
cat.Detailed
applicationBreakdown
voltage
UL flame retardant certificate
Color Price
Polyester Film
GraphicPrinting,
engraving, label
No data None Transparent Low
DISPLAY Display
Diffusion plateNo data None Transparent Low
Electric & electronic use
Covering wireInsulation, Fire proof
125 17Kv188 19Kv
VTM - 2
Increase of insulation
chipMilky (Semi-transparent)
High
5. E.V.A, E.E.A, heat resistant adhesives for ENERPIA FILM Heater
Adhesives for laminating in process of manufacturing heating film are mainly applied with E.V.A (Ethylene-vinylacetate) and E.E.A (Ethylene-Ethylacylate).
Adhesion of laminating part is very important for heating film to prevent from moisture penetration, thermal resistance and formation of air layer in the film.
DAEWOO ENERTEC,
INC7/10
1.Overall coating type vs Strip type
Comparison with other product(Ⅰ)
Hottest part
Overall coating type Q=V²/R- If a spark occurs, it is spread over all area.- Leakage current is very large.
Strip type Q=V²/R=I²xR- If a spark occurs, it is limited to a strip.- Leakage current is limited to a strip. ex) 13mA at 50cm 250Watt.
Current
Overall coated planar heating film
Strip type of planar heating film
DAEWOO ENERTEC, INC
8/10
Overall coating method Strip type printing method
Uneven temperature due to uneven thickness of coating
Very difficult practically to have uniform coating on the area (Including both direction of MD and TD to be coated). Current tends to flow toward lower resistance like water, so temperature deviation between sectional cold part and hot part may occur irregularly, if there is resistance deviation due to lack of uniformity.
Resistance per strip is relatively uniform, and then temperature distribution is comparatively uniform. Also PET film (Polyester film) applied to the product is a top grade of film excellent in electric insulation, physical, chemical and mechanical properties, which is available only from SKC Toray and Saehan.
Fire risk due to overall heating
Heat is generated from whole area, so it has very high probability to make fire if heat is not released because of pressure of heavy objects such as refrigerator.
Its relatively safe because it has spaces not to generate heat, through which heat can be released.
Spread of spark and fire from defected part / Risk of electric shock
If a spark occurs, it spread over all area.Leakage current is very large.
If a spark occurs, it is limited to a strip.Leakage current is limited to a strip..Ex) 13mA at 50cm 250Watt
Handling of cutting part at installation
Entire insulation and water proofing treatment on both copper tape part and carbon heating layer are required.
Carbon heating layer has the uncoated cutting line, so it is all right if only copper tape part is treated well.
Conventional overall coating method
The procedure of overall coating method is to coat conductive carbon ink after laying copper bus bar as electrodes on non-woven base film, which is a part to have mostly electrical troubles. Coating thickness is respectively very thinner than copper bus bar, so it makes the remarkable difference of thickness between copper bus bar part and base film part, which is a factor for electrical troubles.
Materials used for film are non-woven fabrics to absorb moisture well and PET film with perfect insulation property without blocking moisture, so it does not make any electrical troubles due to moisture.
Comparison with other product(Ⅱ)
DAEWOO ENERTEC,
INC9/10
ENERPIA A Co.
Design of Copper Busbar and Silver busbar
Copper Busbar
Silver busbar
Copper Busbar
Silver Busbar
Comparison with other product(Ⅲ)
Electric current flow through the cooper busbar. Allowable current can high when use wider copper busbar. However the thickness of the cooper busbar is also important.
Silver Busbar: The Product of A co. is focus on do not meet the copper and carbon. So it is well prevent the resistance. However electric current floor less. When less electric current flows, there appears a problem of heat.
DAEWOO ENERTEC,
INC10/10