engineering 1182 solidworks settings and helpful hints rev: 2015-03-02, rcbusick 1 table of contents...
TRANSCRIPT
• Engineering 1182
1
Solidworks Settings and Helpful Hints
Rev: 2015-03-02, RCBUSICK
Table of Contents (TOC)• Settings – Pinning the Display – Cleaning up the Model Tree Display – Eliminating Shadows and Reflections – Removing Tangent Edges
• Helpful Hints – Lost Quick Access Toolbar – Correcting AEV Parts Changing Size – Changing Part Orientation – Changing Units Specifications (inch/meter) – Changing Display Style (shaded/hidden lines visible/etc.) – Changing Display Scale – Escaping Title Block Edit Mode – Removing Unwanted Parenthesis in Dimensions – Making Dimension’s Format meet EEIC Standards – Modifying the Template for Proper Dimensioning – Restoring Missing Hidden Lines in Drawing – Simplifying Dimensioning using Symmetry – Saving a Drawing Template – Re-establishing Location of Detached Toolbar – Establishing the Proper Part’s Material to Determine Mass Properties
Slides with animations should be shown in Slide Show Mode.
• Engineering 1182
2
Settings - Pinning the Display
Select the ‘Pin’
Display stays
Original Display
Click on ‘SOLIDWORKS’
Click to return to TOC
• Engineering 1182
3
Settings - Cleaning up the Model Tree Display
Right click and select Hide/Show Tree Items
Click ‘OK’
Change as shown
Click to return to TOC
• Engineering 1182
SolidWorks Layout 4
Eliminating Shadows and Reflections
Click to return to TOC
Entry “darkened” causes reflections
Entry “darkened” causes shadows
Click on “View Settings”
• Engineering 1182
SolidWorks Layout 5
Eliminating Shadows and Reflections
Click to return to TOC
Click entry so now entry “not darkened” and shadowseliminated
Click entry so now entry “not darkened” and reflectionseliminated
• Engineering 1182
SolidWorks Layout 6
Removing Tangent Edges
Rev: 2015-03-02, RCB Click to return to TOC
Tangent Edge
Tangent Edge Visible Tangent Edge Removed
• Engineering 1182
7
Helpful Hints – Lost Quick Access Toolbar
Click to return to TOC
1
1. Select View
2
2. Then Select Workspace
3
3. Finally Click on Default
• Engineering 1182
9
Helpful Hints – Changing Part OrientationSometimes you need to re-orient your part so that the CHARACTERISTIC view will be the FRONT View when the part is extracted to a SolidWorks Drawing.
Select CTRL + 7 keys to orient object into ISO View and select the FRONT face(dark blue)
Select CTRL + 1 keys to orient the object to “Normal To” the current FRONT view
Right click on the blue selected face and under Zoom/Pan/Rotate select View Orientation
Then under Orientation select Left to cause the current FRONT view to be re-assigned to the LEFT View. Then select Update Standard Views at the top of the dialog box and click on YES
Select CTRL + 7 keys to orient the object to it’s newly assigned FRONT and ISO View
Click to return to TOC
• Engineering 1182
10
Helpful Hints - Changing Units Specifications (inch/meter)
1-Under Tools, select OptionsUnder Options select Document Properties and then click on Units
Click on appropriate Units specification and then select OK
Note: Units specifications can be changed for both parts or drawings and should be done prior to sizing an object or applying dimensions to a drawing
Click to return to TOC
• Engineering 1182
11
Helpful Hints – Changing Display Style (shaded/hidden lines visible/etc.)
Drag to reposition
Right click on Isometric and select another style
or
Click to return to TOC
• Engineering 1182
12
Helpful Hints – Changing the Display ScaleSometimes it is helpful to change the scale of the Isometric and add the appropriate note.
More space for Ortho drawings and dimensioning
NOTE: All views can be dragged to reposition and some views are locked to other viewsClick to return to TOC
• Engineering 1182
13
exit by right clicking to get dialog box …
Helpful Hints – Escaping Title Block Edit Mode
After you have completed the TITLE BLOCK(via Edit
Sheet Format) with all CAPS,
Note that during Edit Sheet Format your drawings disappear
Drawings reappear
then select Edit Sheet.
Click to return to TOC
• Engineering 1182
14
Helpful Hints – Removing Unwanted Parenthesis in Dimensions
When you start Dimensioning do you see 'unwanted' parenthesis
You could eliminate the parenthesis by unclicking the 'parenthesis' box
to produce this result
Click to return to TOC
• Engineering 1182
15
Helpful Hints – Removing Unwanted Parenthesis(cont’d)
But it is really tiresome to do that for every dimension !
• Go to Tools/Options/Document Properties and click on Dimension.
• Deselect Add parenthesis by default and click OK!
Click to return to TOC
• Engineering 1182
16
Helpful Hints – Making Dimension’s Format meet EEIC Standards• Go to Tools/Options/Document Properties/Dimensions and make these
changes to each category listed below ( change font to 14 and select )
• To change the font, click on Font, then select points and then 14 and then OKAngle
Arc Length Chamfer Diameter
Hole Callout
Linear Ordinate Radius
Click to return to TOC
• Engineering 1182
17
Helpful Hints - Modifying the Template for Proper Dimensioning
If after you bring up the OSU template and try to dimension a hole you find the following incorrect format:
To correct it, go to Tools/Options/Document Properties and even if you find ANSI (which is the desired format), open the menu using the down arrow and select anything else ( like ISO) and click OK.
Then return to Tools/Options/Document Properties and select ANSI and click OK. When you dimension the hole you find the correct format.
Click to return to TOC
• Engineering 1182
18
Helpful Hint – Restoring Missing Hidden Lines in Drawing
…then under Tools/ Options / System Options / Drawings, select Display Style and click on Hidden lines visible and then OK.
Click to return to TOC
• Engineering 1182
Helpful Hints – Simplifying Dimensioning Using Symmetry
• Use SYMMETRY note to simplify dimensioning
• When you have holes that are symmetrical, dimension center mark to center mark
Click to return to TOC
• Engineering 1182
20
Helpful Hints – Saving a Drawing Template
After making any desired changes in Document Properties and filling out the Title Block with your name and other fixed data and exiting the Edit Sheet Format mode:
1. Click on File / Save as2. Rename the file (perhaps your initials)3. Open the menu under Save as type by clicking the
arrow to the right 4. Then select Drawing Templates [*.drwdot]5. Click on Save6. In the future, this named template will appear
whenever you perform a New along with the other Part / Assembly / Drawing options
Click to return to TOC
• Engineering 1182
SolidWorks Layout 21
Re-establishing Location of Detached Toolbar
Click to return to TOC
Detached ToolbarDetached Toolbar
Drag it near to box with up arrow
Detached Toolbar
Drag it under the box with up arrow, moving to left and/or right until BLUE BORDER appears. Then release mouse button.
Toolbar is now attached to top of window
• Engineering 1182
SolidWorks Layout 22Rev: 20121023, AJP
Establishing Material Properties Mass Properties
If Material is NOT displayed at the top of the Design Tree, right click anywhere in the Design Tree area and select ″Hide/Show Tree Items…″ to produce the ″System Options - FeatureManager″ drop down list as shown on next slide.
If the Material entry is already available, CLICK HERE.
• Engineering 1182
SolidWorks Layout 23
Establishing Material Properties Mass PropertiesIn the System Options – FeatureManager table change the Material setting to ″Show″ and click on ″OK″ to create Material < not specified> in the Design Tree.
• Engineering 1182
SolidWorks Layout 24
Establishing Material Properties Mass PropertiesOnce the ″Material″ field is available in the Design Tree, right click on it and select ″Edit Material″ to produce the ″Material″ drop down list where you can select the desired material, select ″Apply″ and then ″Close″.
• Engineering 1182
SolidWorks Layout 25
Establishing Material Properties Mass PropertiesAfter properly establishing the part’s material(in this case ″Alloy Steel″), select ″Tools / Mass Properties″ to produce the ″Mass Properties″ table to access items such as Density, Mass, Volume, Surface area, Center of Mass, etc.,.
The selected material will then be displayed in the Design Tree.
Click to return to TOC