engineering standard specification...

ENGINEERING STANDARD SPECIFICATION Ontario

TITLE

PLANT SPECIFICCCNR IPC PLANT PIPING SYSTEMMATERIAL SPECIFICATION

VALE #SPEC-65050

PAGE

1/58Last Revision

2020/06/15REV.

6

Rev Description Rev’nby

AppSud

Issue DateYYYY/MM/DD

1 Specification updated and format and number revised.Previous number 6504.01.01.611

AC2012/01/12

AC2012/01/12

2012/05/01

2 SealX Gaskets, Items 19.6 and 19.7 added T.Palmquist M.Fogarty 2016/12/16

3Updated Items 6.54, 7.72, 7.73, 7.74. 13.5, 13.6, 13.7,13.24, 14.1, 14.2, 14.6, 14.7, 14.8, 14.16, 14.17, 17.24,17.33, 30.64, 30.65 added / modified.

K.L.Robin C.Seiler 2019/02/25

4 Added item 5.60 K.L.Robin T.Palmquist 2019/04/22

5 Added item 17.38; Updated items 19.1, 19.3, 19.4 C.S.Seiler K.L. Robin 2019/07/12

6 Changed item 13.24 pressure / temperature rating codeto MSS-SP-110 K.L.Robin T.Palmquist 2020/06/15


TITLE


VALE #SPEC-65050

PAGE

2/58Last Revision

2020/06/15REV.

6

1.0 PURPOSE

This specification describes the minimum requirements for piping systems located at theCCNR IPC plant located in Sudbury, Ontario or at other Vale approved locations.

2.0 APPLICATION

This specification, applies at any Vale locations indicated with approval on the cover page,with the following exceptions:

2.1 EXCEPTIONS

None.

3.0 REFERENCE DOCUMENTATION

The following documents were used in the development of this document or haveinstructions and procedures applicable to it. They shall be used in their most recent revision.

6500-01.01.011 CCNR IPC Plant Piping System – General RequirementsSPEC-35002 Piping – General Requirements


TITLE


VALE #SPEC-65050

PAGE

3/58Last Revision

2020/06/15REV.

6

TABLE OF CONTENTS1.0 PURPOSE 2

2.0 APPLICATION 2

2.1 EXCEPTIONS 2

3.0 REFERENCE DOCUMENTATION 2

4.0 GLOSSARY 5

5.0 SECTION 1 – PIPING 6

6.0 SECTION 2 – FITTINGS 9

7.0 SECTION 3 – UNIONS 13

8.0 SECTION 4 – FLANGES 14

9.0 SECTION 5 – GATE VALVES 19

10.0 SECTION 6 – GLOBE VALVES 24

11.0 SECTION 7 – CHECK VALVES 28

12.0 SECTION 8 – NEEDLE VALVES 32

13.0 SECTION 9 – PLUG VALVES 34

14.0 SECTION 10 – DIAPHRAGM VALVES 37

15.0 SECTION 11 – BUTTERFLY VALVES 38

16.0 SECTION 12 – SPECIAL VALVES 40

17.0 SECTION 13 – BALL VALVES 42

18.0 SECTION 14 – STEAM TRAPS 44

19.0 SECTION 15 – STRAINERS 45


TITLE


VALE #SPEC-65050

PAGE

4/58Last Revision

2020/06/15REV.

6

20.0 SECTION 17 – HOSE 47

21.0 SECTION 19 – GASKETS 50

22.0 SECTION 20 - JOINT MATERIALS 51

23.0 SECTION 21 - BOLTS 52

24.0 SECTION 22 - PURGE FITTINGS (NEW) 53

25.0 SECTION 25 - SIGHT FLOW INDICATORS 54

26.0 SECTION 30 - MISCELLANEOUS 55

26.1 OPERATORS ARE SUPPLIED WITH THE VALVE 56

27.0 APPENDICES 57


TITLE


VALE #SPEC-65050

PAGE

5/58Last Revision

2020/06/15REV.

6

4.0 GLOSSARY

EQUALA manufacturer’s product which meets or exceeds the degree of quality, value, andmaterial in accordance with industry standards and/or specifications.

APPROVED EQUALA manufacturer’s product which meets or exceeds the degree of quality, value, andmaterial in accordance with industry standards and/or specifications and approved bya Vale Representative.

NO SUBSTITUTENo other product, component, device, etc. is acceptable as a replacement for thespecified manufacturer’s product. A detailed evaluation and test work by Vale isrequired to change the specified product.

SSPSteam Saturated Pressure

CWPCold Working Pressure

WOGWater Oil Gas


TITLE


VALE #SPEC-65050

PAGE

6/58Last Revision

2020/06/15REV.

6

5.0 SECTION 1 – PIPING

ITEM NO. DESCRIPTION1.1 UPGRADED. SEE ITEM 1.13

1.5 UPGRADED. SEE ITEM 1.13



1.13 Carbon Steel pipe ASTM A106, Grade B, seamless, Schedule 40,ASME B36.10M. Hot-finished, plain-end random lengths. Mill testcertificate required.

1.14 Carbon Steel pipe ASTM A106, Grade B, seamless, Schedule 80 ASMEB36.10M. Hot-finished, plain-end random lengths. Mill test certificaterequired.


1.28 Carbon Steel pipe ASTM A106 Grade B, seamless, 0.375” wall ASMEB36.10M. Hot-finished, plain-end , random lengths. Mill test certificaterequired. Taper boring of pipe covered by this specification shall benecessary when making tie-ins to existing thinner walled pipe (0.250”wall).

1.29 Carbon Steel pipe, electric fusion welded ASTM A672, Grade C55,Class 12, 0.250” wall ASME B36.10M, plain-end, random lengths. Milltest certificate required.


1.31 Austenitic Stainless Steel pipe, ASTM A312, GR. TP316L, seamless.Schedule 40S, ASME B36.19M, plain-end beveled, random lengths. Milltest certificate required.

1.32 Carbon Steel pipe for low temperature service ASTM A333 Gr. 6,seamless, Schedule 80 ASME B36.10M plain-end beveled, randomlengths. Mill test certificate required.

1.33 Carbon Steel pipe ASTM A106 Gr. B, seamless, Schedule 160 ASME


TITLE


VALE #SPEC-65050

PAGE

7/58Last Revision

2020/06/15REV.

6

B36.10M. Hot-finished, plain-end beveled, random lengths. Mill testcertificate required.


1.35(Added 6504-.01.01.611,

Ver.1)

Carbon Steel pipe for low temperature service ASTM A333 Gr. 6,seamless, Schedule 40 ASME B36.10M, plain-end beveled, randomlengths. Mill test certificate required.

1.36(Added 6504-.01.01.611,

Ver.1)

Carbon Steel pipe for low temperature service, ASTM A333 Gr. 6,seamless, 0.375” wall ASME B36.10M. Hot-finished, plain-end, randomlengths. Mill test certificate required. Taper boring of pipe covered bythis specification shall be necessary when making tie-ins to existingthinner walled pipe (0.250” wall).

1.69(Added 6504-.01.01.611,Rev.1)PreviouslyContained inItem 1.71

Carbon Steel tubing ASTM A179, seamless, cold drawn, randomlengths, hardness Rb72 or less, free of scratches, 0.065 minimum wall.Mill test certificate required. Suitable for bending or flaring.

1.70(Added 6504-.01.01.611,Rev.1)PreviouslyContained inItem 1.71

Carbon Steel tubing ASTM A179, seamless, cold drawn, randomlengths, hardness Rb72 or less, free of scratches, 0.083 minimum wall.Mill test certificate required. Suitable for bending or flaring.

1.71 Carbon Steel tubing ASTM A179, seamless, cold drawn, randomlengths, 0.095” minimum wall, hardness Rb72 or less, free of scratches,mill test certificate required. Suitable for bending or flaring.

1.72 Carbon Steel pipe ASTM API 5L, grade B, submerged arc welded,0.375” wall, ASME B36.10M, plain-end, random lengths. Mill testcertificate required.

1.73 Carbon Steel pipe ASTM A106 Grade B, seamless, 0.375” wall ASMEB36.10M. Hot-finished, plain-end beveled, random lengths. Mill testcertificate required. Taper boring of pipe covered by this specificationshall be necessary when making tie-ins to existing thinner walled pipe(0.281” wall).


TITLE


VALE #SPEC-65050

PAGE

8/58Last Revision

2020/06/15REV.

6

1.74(Added 6504-.01.01.611,

Ver.1)

Carbon Steel pipe for low temperature service, ASTM A333 Gr. 6,seamless, 0.375” wall, ASME B36.10M. Hot-finished, plain-end beveled,random lengths. Mill test certificate required. Taper boring of pipecovered by this specification shall be necessary when making tie-ins toexisting thinner walled pipe (0.281” wall).

1.77 Stainless Steel tubing ASTM A269, Grade TP 316L, seamless, 0.049”average wall thickness, cold finished, hardness Rb80 or less, free ofscratches, random lengths. Mill test certificate required. Suitable forbending or flaring.

1.78(Added 6504-.01.01.611,

Ver.1)

Stainless Steel tubing ASTM A269, Grade TP 316L, seamless, 0.035”average wall thickness, cold finished, hardness Rb80 or less, free ofscratches, random lengths. Mill test certificate required. Suitable forbending or flaring.

1.79(Added 6504-.01.01.611,

Ver.1)


1.80(Added 6504-.01.01.611,

Ver.1)



TITLE


VALE #SPEC-65050

PAGE

9/58Last Revision

2020/06/15REV.

6

6.0 SECTION 2 – FITTINGS

ITEM NO. DESCRIPTION2.1 Wrought carbon steel butt weld fittings ASTM A234 Gr. WPB, seamless,

Schedule 40, ASME B16.9. Elbows are to be long radius (1.5xD) unlessnoted otherwise. Hydrostatic testing not required unless specified.CERTIFICATE OF COMPLIANCE WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER REQUIRED.

2.2 Wrought carbon steel butt weld fittings ASTM A234 Gr. WPB, seamless,Schedule 80, ASME B16.9. Elbows are to be long radius (1.5xD) unlessnoted otherwise. Hydrostatic testing not required unless specified.CERTIFICATE OF COMPLIANCE WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER REQUIRED.

2.3 Wrought carbon steel butt weld fittings ASTM A234 Gr.WPB, seamless,0.375” wall, ASME B16.9. Elbows are to be long radius (1.5xD) unlessnoted otherwise. Hydrostatic testing not required unless specified.CERTIFICATE OF COMPLIANCE WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER REQUIRED.

2.5 Wrought carbon steel butt weld fittings ASTM A234 Gr. WPB-W,welded, 0.250” wall, ASME B16.9. Elbows are to be long radius (1.5xD)unless noted otherwise. CERTIFICATE OF COMPLIANCE WITH REFERENCE TOTHE CANADIAN REGISTRATION NUMBER REQUIRED.

2.6(Added 6504-.01.01.611,Ver.1)

Wrought carbon steel butt weld fittings ASTM A234 Gr. WPB, seamless,0.375” wall, ASME B16.9. Elbows are to be long radius (1.5xD) unlessnoted otherwise. Taper boring of fittings covered by this specificationshall be necessary when making tie-ins to existing thinner walled pipe orfittings (0.250” wall). CERTIFICATE OF COMPLIANCE WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER REQUIRED.

2.7(Added 6504-.01.01.611,Ver.1)

Wrought carbon steel butt weld fittings for low temperature serviceASTM A420 Gr. WPL6, seamless, Schedule 40, ASME B16.9. Elbowsare to be long radius (1.5xD) unless noted otherwise. Hydrostatic testingnot required unless specified. CERTIFICATE OF COMPLIANCE WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER REQUIRED.

2.8(Added 6504-.01.01.611,

Wrought carbon steel butt weld fittings for low temperature serviceASTM A420 Gr. WPL6, seamless, 0.375” wall, ASME B16.9. Elbows are


TITLE


VALE #SPEC-65050

PAGE

10/58Last Revision

2020/06/15REV.

6

Ver.1) to be long radius (1.5xD) unless noted otherwise. Hydrostatic testing notrequired unless specified. CERTIFICATE OF COMPLIANCE WITH REFERENCETO THE CANADIAN REGISTRATION NUMBER REQUIRED.

2.9 Cupola malleable iron fittings ASTM A197, threaded, Class 300, ASMEB16.3. CERTIFICATE OF COMPLIANCE WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER REQUIRED.

2.10(Added 6504-.01.01.611,Ver.1)

Wrought carbon steel butt weld fittings for low temperature serviceASTM A420 Gr. WPL6, seamless, 0.375” wall, ASME B16.9. Elbows areto be long radius (1.5xD) unless noted otherwise. Hydrostatic testing notrequired unless specified. Taper boring of fittings covered by thisspecification shall be necessary when making tie-ins to existing thinnerwalled pipe or fittings (0.250” wall). CERTIFICATE OF COMPLIANCE WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER REQUIRED.

2.13 Forged carbon steel fittings ASTM A105N, Class 3000, socket weld toASME B16.11. TEST REPORT WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER REQUIRED.

2.15 Forged carbon steel fittings ASTM A105N, Class 3000, threaded ASMEB16.11. TEST REPORT WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER REQUIRED.

2.17 Forged carbon steel “Weldolet”, “Threadolet”, or “Elbolet” fittings ASTMA105N, schedule to match run pipe, MSS-SP-97, ASME B16.25, ASMEB1.20.1. TEST REPORT WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER REQUIRED.

2.18(Added 6504-.01.01.611,Ver.1)

Forged carbon steel “Weldoflange”, “Nipoflange”, “Elboflange”, or“Latroflange” fittings ASTM A105N, schedule to match run pipe, raisedface, Class 300, MSS-SP-97, ASME B16.25, flange dimensions toASME B16.5. WFI International or approved equal. TEST REPORT WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER REQUIRED.

2.19(Added 6504-.01.01.611,Ver.1)

Forged carbon steel “Weldoflange”, “Nipoflange”, “Elboflange”, or“Latroflange” fittings ASTM A105N, schedule to match run pipe, raisedface, Class 600, MSS-SP-97, ASME B16.25, flange dimensions toASME B16.5. WFI International or approved equal. TEST REPORT WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER REQUIRED.

2.20 Wrought carbon steel butt weld fittings for low temperature serviceASTM A420 Gr. WPL6, Schedule 80, seamless, ASME B16.9. Elbows


TITLE


VALE #SPEC-65050

PAGE

11/58Last Revision

2020/06/15REV.

6

are to be long radius (1.5xD) unless noted otherwise. CERTIFICATE OFCOMPLIANCE WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.

2.21 Wrought carbon steel butt weld fittings ASTM A234 Gr. WPB, seamless,Schedule 160, ASME B16.9. Elbows are to be long radius (1.5xD)unless noted otherwise. CERTIFICATE OF COMPLIANCE WITH REFERENCE TOTHE CANADIAN REGISTRATION NUMBER REQUIRED.

2.38 Forged carbon steel “Weldolet”, or “Elbolet” fittings for low temperatureservice ASTM A350 Gr. LF2, schedule to match run pipe, MSS-SP-97,ASME B16.25. TEST REPORTS REQUIRED WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER REQUIRED.

2.39(Added 6504-.01.01.611,Ver.1)

Forged carbon steel “Weldoflange”, “Nipoflange”, “Elboflange”, or“Latroflange” fittings for low temperature service, ASTM A350 Gr. LF2,schedule to match run pipe, raised face, Class 300. MSS-SP-97, ASMEB16.25, ASME B16.5. WFI International or approved equal. TESTREPORT WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.

2.40(Added 6504-.01.01.611,Ver.1)

Forged carbon steel “Weldoflange”, “Nipoflange”, “Elboflange”, or“Latroflange” fittings for low temperature service, ASTM A350 Gr. LF2,schedule to match run pipe, raised face, Class 600. MSS-SP-97, ASMEB16.25, ASME B16.5. WFI International or approved equal. TESTREPORT WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.

2.50 Forged stainless steel, seamless fittings, ASTM A403, Gr. WP-S316L,butt weld, schedule 40S, ASME B16.9, ASME B36.19M. Elbows are tobe long radius (1.5xD) unless noted otherwise. CERTIFICATE OFCONFORMANCE WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.

2.51 Forged stainless steel “Weldolet”, ASTM A182, Gr. F316L, schedule 40,MSS-SP-97, ASME B16.9. TEST REPORTS WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER REQUIRED.

2.52(Added 6504-.01.01.611,Ver.1)

Forged stainless steel “Weldoflange”, “Nipoflange”, “Elboflange”, or“Latroflange” fittings ASTM A182 Gr. F316L, schedule to match runpipe, raised face, Class300, MSS-SP-97, ASME B16.25, flangedimensions to ASME B16.5. WFI International or approved equal. TEST


TITLE


VALE #SPEC-65050

PAGE

12/58Last Revision

2020/06/15REV.

6

REPORT WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.

2.53(Added 6504-.01.01.611,Ver.1)

Forged stainless steel “Weldoflange”, “Nipoflange”, “Elboflange”, or“Latroflange” fittings ASTM A182 Gr. F316L, schedule to match runpipe, raised face, Class150, MSS-SP-97, ASME B16.25, flangedimensions to ASME B16.5. WFI International or approved equal. TESTREPORT WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.

2.77 Stainless Steel mechanical fittings AISI Type 316, compression type,including male and female unions, elbows male and female run tees,reducing unions, etc..,. Swagelok Co., “Swagelok”. No substitutes. TESTREPORT WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.

2.78(Added 6504-.01.01.611,

Ver.1)

Stainless Steel mechanical fittings AISI Type 316, “O” ring face sealtype, Viton “O” ring seal. Cajon VCO. No substitutes. TEST REPORT WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER REQUIRED.

2.88 Carbon Steel mechanical fittings, compression type, including male andfemale unions, elbows male and female run tees, reducing unions, etc..,Swagelok Co., “Swagelok”. No substitutes. TEST REPORT WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER REQUIRED.


TITLE


VALE #SPEC-65050

PAGE

13/58Last Revision

2020/06/15REV.

6

7.0 SECTION 3 – UNIONS

ITEM NO. DESCRIPTION3.2 Cupola malleable iron union, ASTM A197, Class 300, bronze to bronze

seats, ground joint, threaded ASME B1.20.1, ASME B16.39.CERTIFICATE OF COMPLIANCE WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER REQUIRED.

3.3 Cupola malleable iron union, ASTM A197, Class 300, iron-to-iron seats,ground joint, threaded ASME B1.20.1, ASME B16.39. CERTIFICATE OFCOMPLIANCE WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.

3.15 Forged carbon steel union, ASTM A105N, Class 3000, integral steelseats, ground joint, threaded ASME B1.20.1. TEST REPORT WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER REQUIRED.

3.16(Added 6504-.01.01.611,

Ver.1)

Forged stainless steel union, ASTM A182 Grade F316L, Class 3000,integral stainless steel seats, ground joint, socket ends ASME B16.21.TEST REPORT WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.


TITLE


VALE #SPEC-65050

PAGE

14/58Last Revision

2020/06/15REV.

6

8.0 SECTION 4 – FLANGES

ITEM NO. DESCRIPTION4.1 Forged carbon steel flange ASTM A105N, slip-on type, Class 150,

raised face, ASME B16.5. TEST REPORT WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER REQUIRED.

4.2 Forged carbon steel flange ASTM A105N, slip-on type, Class 150,except full flat face, ASME B16.5. TEST REPORT WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER REQUIRED.

4.3 Forged carbon steel flange ASTM A105N, weld neck type bored tomatch schedule 40 pipe, Class 150, raised face, ASME B16.5. TESTREPORT WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.

4.4 Forged carbon steel flange ASTM A105N, weld neck type bored tomatch schedule 40 pipe, Class 150, ASME B16.5 except full flat face.TEST REPORT WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.


4.9 Forged carbon steel flange ASTM A105N, blind type, Class 150, raisedface ASME B16.5. TEST REPORT WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER REQUIRED..

4.10(Added 6504-.01.01.611,

Ver.1)

Forged carbon steel flange ASTM A105N, blind type, Class 150, exceptflat face ASME B16.5. TEST REPORT WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER REQUIRED.

4.11 Forged carbon steel flange ASTM A105N, threaded, Class 150, raisedface, ASME B16.5. TEST REPORT WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER REQUIRED.

4.12 Forged carbon steel flange ASTM A105N, threaded, Class 150, ASMEB16.5, except full flat face. TEST REPORT WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER REQUIRED.


TITLE


VALE #SPEC-65050

PAGE

15/58Last Revision

2020/06/15REV.

6

4.13 Forged carbon steel flange ASTM A105N, weld neck type bored tomatch run pipe, Class 150, raised face, ASME B16.5. TEST REPORT WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER REQUIRED.

4.14 Forged carbon steel flange ASTM A105N, weld neck type bored tomatch schedule 80 pipe, Class 150, ASME B16.5, except full flat face.TEST REPORT WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.

4.16 Forged carbon steel flange ASTM A105N, threaded, Class 300, raisedface, ASME B16.5. TEST REPORT WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER REQUIRED.

4.17 Forged carbon steel flange ASTM A105N, slip-on type, Class 300,raised face, ASME B16.5. TEST REPORT WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER REQUIRED.

4.18 Forged carbon steel flange ASTM A105N, weld neck type bored tomatch schedule 40 pipe, Class 300, raised face ASME B16.5. TESTREPORT WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.


4.23 Forged carbon steel flange ASTM A105N, blind type, Class 300, raisedface, ASME B16.5. TEST REPORT WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER REQUIRED.

4.24 Forged carbon steel flange ASTM A105N, socket weld, Class 300,raised face, ASME B16.5. TEST REPORT WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER REQUIRED. THE IPC PLANTCURRENTLY DOES NOT USE THIS PRODUCT..



TITLE


VALE #SPEC-65050

PAGE

16/58Last Revision

2020/06/15REV.

6

4.29 Forged carbon steel flange ASTM A105N, weld neck type bored tomatch schedule 80, pipe Class 600, raised face, ASME B16.5. TESTREPORT WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.

4.33 Forged carbon steel flange ASTM A105N, blind type, Class 600, raisedface, ASME B16.5. TEST REPORT WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER REQUIRED..

4.37 Forged carbon steel flange ASTM A105N, slip-on type, Class 150,raised face, ASME B16.47, MSS SP-44. TEST REPORT WITH REFERENCETO THE CANADIAN REGISTRATION NUMBER REQUIRED.

4.38 Forged carbon steel flanges for low temperature service ASTM A350Gr. LF2, weld neck type bored to match schedule 80 pipe, Class 600,raised face, ASME B16.5. TEST REPORT WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER REQUIRED.

4.39(Added 6504-.01.01.611,

Ver.1)

Forged carbon steel flanges for low temperature service ASTM A350Gr. LF2, slip-on type, Class 150, raised face, ASME B16.47, MSS SP-44. TEST REPORT WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER REQUIRED.

4.40(Added 6504-.01.01.611,

Ver.1)

Forged carbon steel flanges for low temperature service ASTM A350Gr. LF2, threaded, Class 150, raised face, ASME B16.5. TEST REPORTWITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER REQUIRED.


4.57 Forged carbon steel flange for low temperature service ASTM A350 Gr.LF2, blind type, Class 600, raised face, ASME B16.5. TEST REPORT WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER REQUIRED.

4.58 Forged carbon steel flange ASTM A105N, socketweld type, Class 150,raised face, ASME B16.5. TEST REPORT WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER REQUIRED.


TITLE


VALE #SPEC-65050

PAGE

17/58Last Revision

2020/06/15REV.

6

4.59 Forged stainless steel flange ASTM A182, Gr. F316L, weld neck type,bored to match schedule 40S pipe, Class 300, raised face, ASMEB16.5. TEST REPORT WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER REQUIRED.

4.60(Added 6504-.01.01.611,

Ver.1)

Forged carbon steel orifice flange ASTM A105N, welding neck, bore tomatch run pipe, Class 300, raised face, ASME B16.36. Furnished inpairs complete with ASTM A193 Grade B7 bolting and jack screws.TEST REPORT WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.

4.61(Added 6504-.01.01.611,

Ver.1)

Forged carbon steel orifice flange ASTM A105N, welding neck, bore tomatch run pipe, Class 600, raised face, ASME B16.36. Furnished inpairs complete with ASTM A193 Grade B7 bolting and jack screws. TESTREPORT WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBERREQUIRED.

4.62(Added 6504-.01.01.611,

Ver.1)

Forged carbon steel flange for low temperature service ASTM A350 Gr.LF2, blind type, Class 300, raised face, ASME B16.5. TEST REPORT WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER REQUIRED.

4.63(Added 6504-.01.01.611,

Ver.1)

Forged carbon steel flange for low temperature service ASTM A350 Gr.LF2, weld neck, bored to match schedule 40 pipe, Class 300, raisedface, ASME B16.5. TEST REPORT WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER REQUIRED.

4.64(Added 6504-.01.01.611,

Ver.1)


4.65(Added 6504-.01.01.611,

Ver.1)

Forged carbon steel flange for low temperature service ASTM A350 Gr.LF2, slip-on, Class 300, raised face, ASME B16.5. TEST REPORT WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER REQUIRED.

4.66(Added 6504-.01.01.611,

Ver.1)



TITLE


VALE #SPEC-65050

PAGE

18/58Last Revision

2020/06/15REV.

6

4.67(Added 6504-.01.01.611,

Ver.1)


4.68(Added 6504-.01.01.611,

Ver.1)

Forged carbon steel flange for low temperature service ASTM A350 Gr.LF2, weld neck, bored to match run pipe, Class 150, raised face, ASMEB16.5. TEST REPORT WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER REQUIRED.

4.69(Added 6504-.01.01.611,

Ver.1)

Forged carbon steel flange for low temperature service ASTM A350 Gr.LF2, slip-on, Class 150, raised face, ASME B16.5. TEST REPORT WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER REQUIRED.

4.70(Added 6504-.01.01.611,

Ver.1)

Forged carbon steel flange for low temperature service ASTM A350 Gr.LF2, blind type, Class 150, raised face, ASME B16.5. TEST REPORT WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER REQUIRED.

4.71(Added 6504-.01.01.611,

Ver.1)

Forged stainless steel flange ASTM A182, Gr. F316L, weld neck type,bored to match schedule 40S pipe, Class 150, raised face, ASMEB16.5. TEST REPORT WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER REQUIRED.

4.72(Added 6504-.01.01.611,

Ver.1)

Forged stainless steel flange ASTM A182, Gr. F316L, blind type, Class150, raised face ASME B16.5. TEST REPORT WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER REQUIRED..


TITLE


VALE #SPEC-65050

PAGE

19/58Last Revision

2020/06/15REV.

6

9.0 SECTION 5 – GATE VALVES

ITEM NO. DESCRIPTION5.3 Bronze gate valve, lockable, ASTM B61, stainless steel seat rings,

bronze wedge, inside-screw bronze rising stem, g e compositionpacking, union bonnet, threaded ends ASME B1.20.1, Class 200, MSSSP-80. Jenkins Fig. 2270-UJ or equal. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

5.8 Bronze gate valve, lockable, ASTM B62, full diameter seat, solid wedgebronze disc, inside-screw bronze non-rising stem, g e compositionpacking, threaded bronze bonnet, threaded ends ASME B1.20.1, Class125, MSS SP-80. Jenkins Fig. 310J or equal. CERTIFICATE OFCOMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER.

5.15 Cast iron gate valve, lockable, ASTM A126 Class B, renewable bronzeseats, bronze trimmed solid disc, bronze stem, bolted bonnet, O.S.&Y.,non-asbestos packing and gaskets, flanged Class 125 ASME B16.1,MSS SP-70, ASME B16.10. Jenkins Fig. No. 454J or equal. CERTIFICATEOF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

5.30 Forged carbon steel gate valve, lockable, ASTM A105N, 13% chromiumtrim, hard face stainless steel seats, stainless steel wedge disc, boltedbonnet with 304 S.S. flexible g e composite gasket, O.S.&Y., threadedends ASME B1.20.1, Class 800. Smith Valve Corportaion Fig 0800-OOOOO or equal. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

5.37 Cast carbon steel gate valve, lockable ASTM A216 Gr. WCB, 12-13%chromium trim, with hardfaced carbon steel seat rings, carbon steelwedge, alloy steel stem, bolted bonnet with low carbon steel gasket,flexible g e packing, O.S.&Y., flanged Class 150, raised face, ASMEB16.34,. Jenkins Fig. J1009B8F or equal. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.


TITLE


VALE #SPEC-65050

PAGE

20/58Last Revision

2020/06/15REV.

6

5.41 Cast carbon steel ball gate valve, lockable, ASTM A216 Gr. WCC, T3trim, non-lubricated ball type carbon steel seating core with nickel-boronweld overlay face seating surface, regular port, Type H body seat withcontained Teflon TFE sealing ring, bolted bonnet with stainless steel-g espiral-wound gasket, injectable Teflon packing with Teflon rings, fluidpacking lubricant, flanged, Class 150, raised face, ASME B16.34. OrbitFig. 1133H. No substitutes. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

5.42 Cast carbon steel ball gate valve, lockable, ASTM A216 Gr. WCC, T3trim, non-lubricated ball type carbon steel seating core with nickel-boronweld overlay face seating surface, full opening port, Type H body seatwith contained Teflon TFE sealing ring, bolted bonnet with stainlesssteel-g e spiral-wound gasket, injectable Teflon packing with Teflonrings, fluid packing lubricant, flanged Class 600, raised face, ASMEB16.34. Orbit Fig. 1423H. No substitutes. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

5.43 Cast carbon steel ball gate valve, lockable, ASTM A216 Gr. WCC, T3trim, non-lubricated ball type carbon steel seating core with nickel-boronweld overlay face seating surface, regular port, Type H body seat withcontained Teflon TFE sealing ring, bolted bonnet with stainless steel-g espiral-wound gasket, injectable Teflon packing with Teflon rings, fluidpacking lubricant, flanged Class 300, raised face, ASME B16.34. OrbitFig. 1233H. No substitutes. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

5.44(Added 6504-.01.01.611,

Ver.1)

Cast carbon steel ball gate valve, lockable, for low temperature serviceASTM A352 Gr. LCC, Low Temp T3 trim, non-lubricated ball typecarbon steel seating core with nickel-boron weld overlay face seatingsurface, full port, Type H body seat with contained Teflon TFE sealingring, bolted bonnet with stainless steel-g e spiral-wound gasket,injectable Teflon packing with Teflon rings, fluid packing lubricant,flanged Class 300, raised face, ASME B16.34. Orbit Fig. 2223H. Nosubstitutes. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TOTHE CANADIAN REGISTRATION NUMBER.


TITLE


VALE #SPEC-65050

PAGE

21/58Last Revision

2020/06/15REV.

6

5.45 Forged carbon steel gate valve, lockable, ASTM A105N, 410 stainlesssteel stem and seat ring, 420 stainless steel wedge, bolted bonnet withstandard 304 S.S. flexible g e composition gasket, g e and braided g eend ring packing, O.S.&Y., Class 300 flanged, raised face, ASME B16.5,ASME B16.10, ASME B16.34. Smith Valve Corporation Fig. No.G830-OOOOO or equal. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

5.46 Cast carbon steel ball gate valve, lockable, for low temperature serviceASTM A352 Gr. LCC, Low Temp T3 trim, non-lubricated carbon steelball type seating core with nickel weld overlay face seating surface, full-opening port, Type H body seat with contained Teflon TFE sealing ring,bolted bonnet with stainless steel-g e spiral wound gasket, injectableTeflon packing and Teflon rings, fluid packing lubricant, flanged Class600, raised face, ASME B16.34. Orbit Fig. No. 2423H. No substitutes.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

5.47(Added 6504-.01.01.611,

Rev.1)Previously

Contained inItem 5.42

Cast carbon steel ball gate valve, lockable, ASTM A216 Gr. WCC, T3trim, non-lubricated ball type carbon steel seating core with nickel-boronweld overlay face seating surface, regular port, Type H body seat withcontained Teflon TFE sealing ring, bolted bonnet with stainless steel-g espiral-wound gasket, injectable Teflon packing with Teflon rings, fluidpacking lubricant, flanged Class 600, raised face, ASME B16.34. OrbitFig. No. 1433H. No substitutes. CERTIFICATE OF COMPLIANCE REQUIREDWITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

5.48(Added 6504-.01.01.611,

Rev.1)Previously


Cast carbon steel ball gate valve, lockable, for low temperature serviceASTM A352 Gr. LCC, Low Temp T3 trim, non-lubricated carbon steelball type seating core with nickel weld overlay face seating surface,regular port, Type H body seat with contained Teflon TFE sealing ring,bolted bonnet with stainless steel-g e spiral wound gasket, injectableTeflon packing and Teflon rings, fluid packing lubricant, flanged Class600, raised face, ASME B16.34. Orbit Fig. No. 2433H. No substitutes.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.


TITLE


VALE #SPEC-65050

PAGE

22/58Last Revision

2020/06/15REV.

6

5.49(Added 6504-.01.01.611,

Ver.1)

Cast carbon steel ball gate valve, lockable, for low temperature serviceASTM A352 Gr. LCC, Low Temp T3 trim, non-lubricated ball typecarbon steel seating core with nickel-boron weld overlay face seatingsurface, full port, Type H body seat with contained Teflon TFE sealingring, bolted bonnet with stainless steel-g e spiral-wound gasket,injectable Teflon packing with Teflon rings, fluid packing lubricant,flanged Class 150, raised face, ASME B16.34. Orbit Fig. 2123H. Nosubstitutes. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TOTHE CANADIAN REGISTRATION NUMBER.

5.54 Forged carbon steel gate valve, lockable, ASTM A105N, 410 stainlesssteel stem and seat ring, 420 stainless steel wedge, bolted bonnet withstandard 304 S.S. flexible g e composition gasket, g e and braided g eend ring packing, O.S.&Y., Class 150 flanged, raised face, ASME B16.5,ASME B16.10, ASME B16.34. Smith Valve Corporation Fig. No.G815-OOOOO or equal. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

5.56 Cast carbon steel ball gate valve, lockable, ASTM A216 Gr. WCC, T3trim, non-lubricated ball type carbon steel seating core with nickel-boronweld overlay face seating surface, full opening port, Type H body seatwith contained Teflon TFE sealing ring, bolted bonnet with stainlesssteel-g e spiral-wound gasket, injectable Teflon packing with Teflonrings, fluid packing lubricant, preferred pressure end flanged Class 300,opposite to preferred pressure end drilled to Class 150, ASME B16.5raised face except drilled to Class 150, ASME B16.34. Orbit Fig. 1223H.No substitutes. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TOTHE CANADIAN REGISTRATION NUMBER.



TITLE


VALE #SPEC-65050

PAGE

23/58Last Revision

2020/06/15REV.

6


5.59(Added 6504-.01.01.611,

Ver.1)

Cast stainless steel ball gate valve, lockable, ASTM A351 Gr. CF8M, T8trim, non-lubricated ball type stainless steel seating core with Ultimetweld overlay face seating surface, full opening port, Type H body seatwith contained Teflon TFE sealing ring, bolted bonnet with stainlesssteel-g e spiral-wound gasket, injectable Teflon packing with Teflonrings, fluid packing lubricant, flanged Class 150, raised face, ASMEB16.34. Orbit Fig. 6128HS. No substitutes. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

5.60(Added rev4)

Cast carbon steel ball gate valve, lockable, for low temperature serviceASTM A352 Gr. LCC, Low Temp, T5 trim, packing to be suitable forammonia service (braided carbon composition). Brass, bronze, orcopper bearing alloys are not permitted in wetted parts. Valve to betagged for Ammonia service, full port, flanged Class 300, raised face,ASME B16.34. Orbit Fig. 2225HL. No substitutes. CERTIFICATE OFCOMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER


TITLE


VALE #SPEC-65050

PAGE

24/58Last Revision

2020/06/15REV.

6

10.0 SECTION 6 – GLOBE VALVES

ITEM NO. DESCRIPTION6.1 Bronze globe valve, lockable, ASTM B61, renewable seat, renewable

stainless steel plug type disc and seat ring, inside-screw bronze risingstem, union bonnet, non-asbestos composition packing, threaded ends,ASME B1.20.1, Class 200, MSS SP-80. Jenkins Fig. 2050J or equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

6.15 Malleable iron globe valve, lockable, ASTM A197, renewable 13% Cr.Stainless steel seat and disc, inside-screw 13% Cr. Stainless steel risingstem, union bonnet, threaded ends, ASME B1.20.1,MSS-SP 85, rated300 SWP. Crane No. 254XR or equal. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

6.17 Cast iron globe valve, lockable, ASTM A126 Class B, renewable bronzeseat, bronze or bronze faced iron disc, bronze rising stem, boltedbonnet, non-asbestos ring packing, O.S.&Y., flanged Class 125, ASMEB16.1, ASME B16.10, MSS SP-85. Jenkins Fig. 2342J or equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

6.25(Added 6504-.01.01.611,

Ver.1)

Forged carbon steel globe valve, lockable, for low temperature service,ASTM A350 Grade LF2, Stellite hardened integral seat, 13% chromiumtrim, with renewable stainless steel plug type disc, bolted bonnet withretained gasket, O.S.&Y., flanged Class 300, raised face, ASME B16.5,ASME B16.10, ASME B16.34. Packing to be suitable for ammoniaservice (braided carbon composition). Brass, bronze, or copper bearingalloys are not permitted in wetted parts. Valve to be tagged for Ammoniaservice. Smith Valve Corporation Fig. G83-TOOOO or approved equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

6.26 Forged carbon steel globe valve, lockable, ASTM A105N, Stellitehardened integral seat, 13% chromium trim, with renewable stainlesssteel plug type disc, bolted bonnet with retained gasket, O.S.&Y.,flanged Class 300, raised face, ASME B16.5, ASME B16.10, ASMEB16.34. Packing to be suitable for ammonia service (braided carboncomposition). Brass, bronze, or copper bearing alloys are not permittedin wetted parts. Valve to be tagged for Ammonia service. Smith Valve


TITLE


VALE #SPEC-65050

PAGE

25/58Last Revision

2020/06/15REV.

6

Corporation Fig. G83-OOOOO or approved equal. CERTIFICATE OFCOMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER.

6.28(Added 6504-.01.01.611,

Ver.1)

Forged carbon steel globe valve, lockable, for low temperature service,ASTM A350 Grade LF2, Stellite hardened integral seat, 13% chromiumtrim, with renewable plug type stainless steel disc, bolted bonnet withretained 304 S.S. flexible g e composition gasket, O.S.&Y., Class 800,threaded ASME B1.20.1, ASME B16.10, ASME B16.34. Packing to besuitable for ammonia service (Braided carbon composition). Brass,bronze, or copper bearing alloys are not permitted in wetted parts. Valveto be tagged for Ammonia service. Smith Valve Corporation Fig.0G80-TOOOO or approved equal. CERTIFICATE OF COMPLIANCE REQUIREDWITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

6.29 Forged carbon steel globe valve, lockable, ASTM A105N, Stellitehardened integral seat, 13% chromium trim, with renewable plug typestainless steel disc, bolted bonnet with retained 304 S.S. flexible g ecomposition gasket, O.S.&Y., Class 800, threaded ASME B1.20.1,ASME B16.10, ASME B16.34. Packing to be suitable for ammoniaservice (Braided carbon composition). Brass, bronze, or copper bearingalloys are not permitted in wetted parts. Valve to be tagged for Ammoniaservice. Smith Valve Corporation Fig. G80-OOOOO or approved equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

6.30 Cast carbon steel globe valve, lockable, ASTM A216 Gr. WCBrenewable 13% chromium seat, renewable carbon steel 13% Cr. Facedplug or ball disc, alloy steel stem, low carbon steel gasket, packing to besuitable for ammonia service (braided carbon composition), boltedbonnet, O.S.&Y., flanged Class 300, raised face, ASME B16.34. Brass,bronze, or copper bearing alloys are not permitted in wetted parts. Valveto be tagged for Ammonia service. Jenkins Fig. J1042B2 or approvedequal. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER.

6.31 Cast carbon steel globe valve, lockable, ASTM A216 Gr. WCB, 12-13%chromium trim, with renewable seat, and plug or ball type disc, boltedbonnet with flexible g e packing, O.S.&Y., flanged Class 150, raisedface, ASME B16.34. Jenkins Fig. No. J1040B2 or equal. CERTIFICATE OFCOMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER.


TITLE


VALE #SPEC-65050

PAGE

26/58Last Revision

2020/06/15REV.

6

6.32(Added 6504-.01.01.611,

Ver.1)

Cast carbon steel globe valve, lockable, ASTM A216 Gr. WCB, 12-13%chromium trim, with renewable seat, and plug or ball type disc, boltedbonnet with flexible g e packing, O.S.&Y., flanged Class 300, raisedface, ASME B16.34. Jenkins Fig. No. J1042B2 or equal. CERTIFICATE OFCOMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER.




6.44 Forged carbon steel globe valve, lockable, ASTM A105N, Stellitehardened integral seat, 13% chromium trim, with renewable plug typestainless steel disc, bolted bonnet with retained 304 S.S. flex. Graph.Comp. gasket, O.S.&Y., braided carbon composition packing, Class800, threaded ends, ASME B1.20.1, ASME B16.34. Smith ValveCorporation Fig. G80-OOOOO or equal. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

6.49 Forged carbon steel globe valve, lockable, ASTM A105N, Stellitehardened integral seat, 13% chromium trim, with renewable stainlesssteel plug type disc, bolted bonnet with retained gasket, regular port,O.S.&Y., flanged Class 300, raised face, ASME B16.5, ASME B16.10,ASME B16.34. Smith Valve Corporation Fig. G83-OOOOO or equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

6.50(Added 6504-.01.01.611,

Ver.1)

Cast stainless steel globe valve, lockable, ASTM A351 Grade CF8M,integral seat, renewable 316 stainless steel plug type disc, stainlesssteel rising stem, bolted bonnet with retained gasket, regular port,O.S.&Y., Teflon packing and bonnet gasket, flanged Class 150, raisedface, ASME B16.5. Kitz 150 UPAM or equal. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

6.51(Added 6504-.01.01.611,

Ver.1)

Stainless steel type 316, bellows type globe valve, lockable, TFEpacking, female “Cajon VCO” type end connections. Nupro “UW Series”,SS-*UW-V**. No substitute. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.


TITLE


VALE #SPEC-65050

PAGE

27/58Last Revision

2020/06/15REV.

6

6.52(Added 6504-.01.01.611,

Ver.1)

Stainless steel type 316, bellows type globe valve, lockable, TFEpacking, Swagelok end connections. Rated 2500 psig @ 650oF. Nupro“UW Series”, SS-*UW. No substitute. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

6.53(Added 6504-.01.01.611,

Ver.1)

Stainless steel type 316, metering valve, lockable, Swagelok endconnections. Rated 600 psig @ 200oF. Nupro “BM Series”, SS-4BMG.No substitute. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TOTHE CANADIAN REGISTRATION NUMBER.

6.54(Added rev 3)

Cast Carbon Steel globe valve rated to ASME B16.34, lockable, ASTMA352 Gr LCC body, stellite seat, 300 class raised face flanges to ASMEB16.5, dimensions to ASME B16.10. Packing to be suitable for ammoniaservice (braided carbon composition), Brass, bronze, or copper bearingalloys not permitted in wetted parts. Valve shall be tagged for ammoniaservice. Velan part VEL F101074C31NB. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER


TITLE


VALE #SPEC-65050

PAGE

28/58Last Revision

2020/06/15REV.

6

11.0 SECTION 7 – CHECK VALVES

ITEM NO. DESCRIPTION7.2 Bronze check valve ASTM B61, horizontal swing type, integral seat,

bronze hinge and threaded cap, regrindable brass disc, Class 200,threaded ends, ASME B1.20.1, MSS SP-80. Jenkins Fig. No. 4449J orequal. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER.

7.10 Forged Steel check valve ASTM A105N, horizontal or vertical swingcheck type, Stellite faced seat ring, 13% Cr. Stainless steel disc, boltedcover, Class 800, threaded ends, ASME B1.20.1, ASME B16.34. CraneNo. FB-3675XU-T or approved equal. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

7.13 Cast iron check valve ASTM A126 Class B, horizontal swing type,renewable bronze seat rings, bronze or bronze trimmed disc, boltedcover, flanged Class 125 ASME B16.1, ASME B16.10, MSS SP-71.Jenkins Fig. No. 587J or equal. CERTIFICATE OF COMPLIANCE REQUIREDWITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

7.30 Forged carbon steel check valve ASTM A105N, piston type, 13% Cr.Stainless Steel trim with Stellite hardened integral seat, piston check,bolted cover, 304 S.S. flexible g e composite gasket, API Class 800,threaded ends, ASME B1.20.1, ASME B16.34. Smith Valve CorporationFig. No. C80-OOOOO or equal. CERTIFICATE OF COMPLIANCE REQUIREDWITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

7.33(Added 6504-.01.01.611,

Ver.1)

Forged carbon steel check valve for low temperature service, ASTMA350 Grade LF2, piston type, 13% Cr. Stainless Steel trim with Stellitehardened integral seat, piston check, bolted cover, 304 S.S. flexible g ecomposite gasket, flanged Class 300, raised face, ASME B 16.5, ASMEB16.10, ASME B16.34. Brass, bronze or copper bearing alloys are notpermitted in wetted parts. Valves to be tagged for ammonia service.Smith Valve Corporation Fig. No. C83-TOOOO or approved equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.


TITLE


VALE #SPEC-65050

PAGE

29/58Last Revision

2020/06/15REV.

6

7.34 Forged carbon steel check valve ASTM A105N, piston type, 13% Cr.Stainless Steel trim with Stellite hardened integral seat, piston check,bolted cover, 304 S.S. flexible g e composite gasket, flanged Class 300,raised face, ASME B 16.5, ASME B16.10, ASME B16.34. Brass, bronzeor copper bearing alloys are not permitted in wetted parts. Valves to betagged for ammonia service. Smith Valve Corporation Fig. No. C83-OOOOO or approved equal. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

7.36 Cast carbon steel check valve ASTM A216 WCB, horizontal swing type,renewable hardfaced carbon steel seat rings, 13% Cr. Trimmed disc,bolted cover, low carbon steel gasket, flanged Class 150, raised face,ASME B16.5, ASME B16.10, ASME B16.34. Jenkins Fig. No. J1025B2or equal. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER.

7.37 Cast carbon steel check valve ASTM A216 WCB, horizontal swing type,13% chromium trim with renewable seat and disc, flanged Class 300,raised face, ASME B16.34. Brass, bronze or copper bearing alloys arenot permitted in wetted parts. Valves to be tagged for ammonia service.Kitz Fig. K-300-SC-OSY or approved equal. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

7.38Note updated

rev3

Cast carbon steel check valve ASTM A216 WCB, horizontal swing type,13% chromium trim, renewable 13% chromium seat, 13% chromiumdisc, bolted cover, flanged Class 600, raised face, ASME B16.34. KitzK-600-SC-OSY or approved equal. Certificate of compliance requiredwith reference to the Canadian Registration Number. IPC Utilitiescurrently uses item 7.72, which is an approved equal.

7.43 Cast carbon steel check valve ASTM A216 WCB, horizontal swing type,13% chromium trim with renewable seat and disc, flanged Class 300,raised face, ASME B16.34. Kitz Fig. K-300-SC-OSY or approved equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

7.44 Cast carbon steel check valve ASTM A216 WCB, horizontal swing type,12-13% chromium trim with renewable seat and disc, flanged Class 150,raised face, ASME B16.34. Kitz Fig. K-150-SC-OSY or approved equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.


TITLE


VALE #SPEC-65050

PAGE

30/58Last Revision

2020/06/15REV.

6

7.64 Forged carbon steel check valve ASTM A105N, piston type, 12-13%chromium trim with hardened integral seat, piston check, bolted cover,flanged Class 600, raised face, ASME B16.5, ASME B16.10. BonneyForge L6-40 or approved equal. CERTIFICATE OF COMPLIANCE REQUIREDWITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

7.65 Cast carbon steel check valve ASTM A36 nickel plated, wafer typebody, 316 SS clapper, stainless steel swivel pin, spring shall beremoved, Teflon seat ring, suitable for installation between Class 150ASME B16.5 flanges. Wheatly Canada Fig No. 977-(size)0027-119.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

THE IPC PLANT CURRENTLY DOES NOT USE THIS PRODUCT DUETO FLAPPER FAILURES.

7.67 Cast iron body, neoprene lined ball check valve, in-line type to fitbetween Class 150 ASME flanges, compression molded neoprene ballslurry service. Rated 200# at 200 Deg. F, Dorr-Oliver Type B.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

THE IPC PLANT CURRENTLY DOES NOT USE THIS PRODUCT DUETO BALL FAILURES.

7.68 THE IPC PLANT CURRENTLY DOES NOT USE THIS PRODUCT..

7.69 THE IPC PLANT CURRENTLY DOES NOT USE THIS PRODUCT.

7.70(Added 6504-.01.01.611,

Ver.1)

Cast stainless steel check valve, ASTM A351 Grade CF8M, swing type,316 stainless steel disc, bolted cover, flanged Class 150, ASME B16.5.Kitz 150 UOAM or equal. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

7.71(Added 6504-.01.01.611,

Ver.1)

Cast stainless steel check valve, ASTM A351 Grade CF8M, piston type,bolted cover, flanged Class 150, ASME B16.5. CERTIFICATE OFCOMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER.

7.72Added rev 3

Cast carbon steel horizontal swing check valve rated to ASME B16.34,ASTM A216 WCB body, stellite seat with 13% Chromium renewable


TITLE


VALE #SPEC-65050

PAGE

31/58Last Revision

2020/06/15REV.

6

disc, bolted cover, Class 600, raised face flanges to ASME B16.5,dimensions to ASME B16.10. Velan 2114C. Certificate of compliancerequired with reference to the Canadian Registration Number.

7.73Added rev 3

Cast Carbon Steel swing check valve rated to ASME B16.34, lockable,ASTM A352 Gr LCC body, stellite seat with renewable seat and disc,300 class raised face flanges to ASME B16.5, dimensions to ASMEB16.10. Brass, bronze, or copper bearing alloys not permitted in wettedparts. Valve shall be tagged for ammonia service. Velan VELF101114C31NB. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCETO THE CANADIAN REGISTRATION NUMBER

7.74Added rev 3

Excess Flow Valve 250 psig rating to ASME B16.34. Brass, bronze, orcopper bearing alloys not permitted in wetted parts. Valve shall betagged for ammonia service. Part Number Rego A3213D150.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER


TITLE


VALE #SPEC-65050

PAGE

32/58Last Revision

2020/06/15REV.

6

12.0 SECTION 8 – NEEDLE VALVES

ITEM NO. DESCRIPTION8.3 Steel body, bar stock, needle globe type, lockable, stainless steel stem,

metal to metal seats, threaded and pinned bonnet, Teflon packing,4,000 psi @ 500oF rating, threaded ASME B1.20.1, female ends.Anderson Greenwood H5VIC-* or equal. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

8.4(Added 6504-.01.01.611,

Rev.1)Previously


Steel body, bar stock needle globe type, stainless steel stem, metal tometal seats, threaded and pinned bonnet, lockable, Teflon packing,4,000 psi @ 500oF rating, threaded ASME B1.20.1, one male end, onefemale end. Anderson Greenwood H5VIC-** or equal. CERTIFICATE OFCOMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER.

8.5 Severe service union bonnet angle valve, lockable, ASTM A479 type316, 316SS bonnet, stem and gland, stellite # 3 ball tip stem. TFEpacking. Rated Class 2500, Max. temp. of 450oF, threaded ASMEB1.20.1, female ends, Whitey SS-*NBF*-A (no substitute) CERTIFICATEOF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

8.6(Added 6504-.01.01.611,

Ver.1)

Steel body, bar stock, needle straight through type, lockable, stainlesssteel stem, PEEK seats, threaded and pinned bonnet, Teflon packing,4000 psig @ 400oF rating, threaded ASME B1.20.1, female ends.Anderson Greenwood H1VEC-* or equal. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

8.7(Added 6504-.01.01.611,

Ver.1)

Steel body, bar stock, needle straight through type, lockable, stainlesssteel stem, PEEK seats, threaded and pinned bonnet, Teflon packing,4000 psi @ 400oF rating, threaded ASME B1.20.1, one male end, onefemale end. Anderson Greenwood H1VEC-**or equal. CERTIFICATE OFCOMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER.

8.8(Added 6504-.01.01.611,

Ver.1)

Stainless steel body, ASTM A182 Grade 316, bonnet needle angle type,lockable, stainless steel regulating stem, PFA packing. Swagelok endconnections. Rated ASME Class 2080. Whitey Bonnet Needle ValveSS-1RS*-A. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TOTHE CANADIAN REGISTRATION NUMBER.


TITLE


VALE #SPEC-65050

PAGE

33/58Last Revision

2020/06/15REV.

6

8.9(Added 6504-.01.01.611,

Ver.1)

Stainless steel body, bar stock, needle straight through type, lockable,stainless steel stem, PEEK seats, threaded and pinned bonnet, Teflonpacking, 4000 psi @ 400oF rating, threaded ASME B1.20.1, one maleend, one female end. Anderson Greenwood H1VES-* or equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.


TITLE


VALE #SPEC-65050

PAGE

34/58Last Revision

2020/06/15REV.

6

13.0 SECTION 9 – PLUG VALVES

ITEM NO. DESCRIPTION9.18 Cast carbon steel plug valve, lockable, ASTM A216 Gr. WCB, short

pattern, lubricated carbon steel plug, stainless steel and g e gasket, g eand TFE packing, wrench operated, complete with wrench, flangedClass 300, raised face, ASME B16.5, ASME B16.10, ASME B16.34.Lubricant suitable for air and natural gas service (Nordstrom 1033).Super Nordstrom Fig. No. 2025 or equal. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

9.41(Added 6504-.01.01.611,

Ver.1)

Cast steel body, ASTM A126 Class B, non-lubricated type, ASTM A216Grade WCB, cast iron plug with resilient face, lockable, locked top &bottom journal bearing with rubber quad ring journal seals, boltedbonnet with retaining gasket, lever operated complete with standardlever for valves 6” and under, gear operated for valves over 6”, flangedClass 150 except flat face, ASME B16.5, Rated 285 C.W.P. Dezurik Fig.128-F-6-RS or equal. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

9.42 Cast iron body soft rubber lined eccentric plug valve, ASTM A126 ClassB, non-lubricated type, ASTM A126 Class B cast iron plug with resilientface, lockable, soft rubber lining shall be pure gum rubber or neoprene,60 to 65 durometer, locked top & bottom journal bearing with rubberquad ring journal seals, bolted bonnet with retaining gasket, leveroperated complete with standard lever for valves 6” and under, gearoperated for valves over 6”, flanged Class 125, flat face, ASME B16.1,Rated 175 C.W.P. Dezurik Fig. 198-F-6-RS or equal. CERTIFICATE OFCOMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER.

9.47 Cast carbon steel twin-seal valve c/w thermal relief to upstream flowsystem, ASTM A216 Gr. WCB, cast steel chromium plated plug withminimum 70% port area, lockable, ductile iron slips ASTMA536-80-55-06 with raph (type V) seals, g e packing, hand wheel gearoperated sizes 10” and larger, flanged Class 150 raised face ASMEB16.5, API 6D. Valve suitable for lethal service. General Valve TwinSeal CX811-G or approved equal. CERTIFICATE OF COMPLIANCE REQUIREDWITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.


TITLE


VALE #SPEC-65050

PAGE

35/58Last Revision

2020/06/15REV.

6

9.48 Cast carbon steel twin-seal valve c/w thermal relief to upstream flowsystem, lockable, ASTM A216 Gr. WCB, cast steel chromium platedplug with minimum 40% port area, ductile iron slips ASTMA536-80-55-06 with graphite (type V) seals, graphite packing, handwheel gear operated sizes 10” and larger, flanged Class 150 raised faceASME B16.5, API 6D. Valve suitable for lethal service. General ValveTwin Seal CX411-G or approved equal. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

9.50 Cast ductile iron plug valve, lockable, ASTM A395, plug 100% full, roundbore lubricated plug, bolted cover with “Durabla” gasket, bolted gland,Teflon packing wrench operated complete with wrench, lubricantsuitable for 395 Deg. F, flanged 300# ASME B16.5. Homestead ValveMfg. Co. Drawing SK-1425.

THIS VALVE IS NO LONGER AVAILABLE. CCNR IS CURRENTLYUSING ITEM 13.6.

9.51 Cast ductile iron plug valve, lockable, ASTM A395, 100% full, roundbore lubricated plug, bolted cover with “Durabla” gasket, bolted gland,Teflon packing wrench operated complete with wrench, lubricantsuitable for 395 Deg. F, flanged 150# ASME B16.5. Homestead ValveMfg. Co. Drawing SK-1425.

THIS VALVE IS NO LONGER AVAILABLE. CCNR IS CURRENTLYUSING ITEM 13.7.

9.52 Cast carbon steel multiport valve, lockable, ASTM A216 Gr. WCB,lubricated type regular pattern carbon steel plug, wrench operated,three-way, two-port, arrangement no. 13, 180 degree turn, stainlesssteel and g e gasket, g e and TFE packing, flanged Class 300 raisedface, ASME B16.5, ASME B16.34. Lubricant suitable for air and naturalgas service (Nordstrom 1033). Super Nordstrom Fig. No. 4803 or equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.


TITLE


VALE #SPEC-65050

PAGE

36/58Last Revision

2020/06/15REV.

6

9.54 Cast carbon steel body eccentric plug valve, lockable, ASTM A216 GrWCB, non-lubricated type ASTM A216 Gr WCB cast carbon steelresilient plug, soft rubber lining shall be pure gum rubber or neoprene,60 to 65 durometer, locked top & bottom journal bearing with rubberquad ring journal seals, bolted bonnet with retaining gasket, leveroperated complete with standard lever for valves 6” and under, gearoperated for valves over 6”, flanged Class 150 ASME B16.5. DezurikFig. 128-F-6-RS or equal. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

9.60(Added 6504-.01.01.611,

Ver.1)

Cast carbon steel plug valve, lockable, ASTM A216 Gr. WCB, packlessnon-lubricated carbon steel ASTM A216 Gr. WCB plug, bolted bonnetwith retaining gasket, lever operated unless specified otherwise, PTFEsleeve, flanged Class 150, raised face, ASME B16.5, ASME B16.34.Tufline Fig. 067-**-2-2-P1-*. No substitute. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

9.61(Added 6504-.01.01.611,

Ver.1)

Cast carbon steel plug valve, lockable, ASTM A216 Gr. WCB, packlessnon-lubricated carbon steel ASTM A216 Gr. WCB plug, bolted bonnetwith retaining gasket, lever operated unless specified otherwise, PTFEsleeve, flanged Class 300, raised face, ASME B16.5, ASME B16.34.Tufline Fig. 0367-**-2-2-P1-*. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.


TITLE


VALE #SPEC-65050

PAGE

37/58Last Revision

2020/06/15REV.

6

14.0 SECTION 10 – DIAPHRAGM VALVES

ITEM NO. DESCRIPTION10.3 CURRENTLY NOT IN USE IN THE IPC PLANT

10.4 Cast ductile iron body full flat face flange neoprene lined diaphragmvalve, lockable, ASTM A395, straightaway type, neoprene diaphragm,neoprene lining, body assembly materials per Manufacturer’s Standard,with stem but no travel stop. Suitable for slurry service 100 PSIG @120°F, flanged Class 125, flat face, ASME B16.1. ITT Dia-Flo Fig. 2840-ST-2 or equal. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TOTHE CANADIAN REGISTRATION NUMBER.

10.7 Cast ductile iron body neoprene lined diaphragm valve, lockable, ASTMA395, weir type, neoprene diaphragm, neoprene lining, bonnetassembly materials per Manufacturer’s Standard, with indicating stembut no travel stop. Suitable for slurry service, 200 PSIG @ 120°F,flanged Class 125, flat face, ASME B16.1. ITT Dia-Flo Fig. 2550-T-2 orequal. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER.

CURRENTLY NOT IN USE IN THE IPC PLANT


TITLE


VALE #SPEC-65050

PAGE

38/58Last Revision

2020/06/15REV.

6

15.0 SECTION 11 – BUTTERFLY VALVES

ITEM NO. DESCRIPTION11.3 Ductile iron body wafer style butterfly valve, lockable, ASTM A395,

stainless steel disc and stem, fully encapsulated BUNA-N seat, standardhandle for size 8” and under, gear operated for sizes 10” and over.Valve to be suitable for mounting between two Class 150/125 flanges.Valve rated 150 psig for sizes 12” and under. Keystone F990-DEE3 orequal. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER.

11.10 Cast carbon steel lug style butterfly valve, lockable, ASTM A216 GradeWCB body, carbon steel disc, 17-4PH stainless steel shaft, raphipacking, filled raphi seat, c/w handwheel gear operator, body providedwith bolting lugs tapped for installation with cap screws. Valve to besuitable for mounting between two Class 150 flanges. Face to facedimensions in accordance with MSS-SP-68. Valve body rated Class150, ASME B16.34. Seat rated rated 200 psig @ 400oF. Jamesbury Fig815L-11-22FB-MT or approved equal. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

11.12 Cast carbon steel body lug style butterfly valve, lockable, ASTM A216Grade WCB, metal to metal seats, stainless steel disc, Type 316stainless steel shaft, plain type stuffing box with PTFE “V” packing, gearoperated, body provided with bolting lugs tapped for installation with capscrews, for installation between Class 150 raised face flanges, ASMEB16.5. Valve body rated Class 150 ASME B16.34. Seat rated 200 psig@ 400 oF. Fisher Continental A41 Butterfly or equal. CERTIFICATE OFCOMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER.

11.14 Cast carbon steel lug style butterfly valve, lockable, ASTM A216 GradeWCB body, stainless steel disc, 17-4PH stainless steel shaft, graphitepacking, filled graphite seat, c/w handwheel gear operator. Bodyprovided with bolting lugs tapped for installation with cap screws. Valveto be suitable for mounting between two Class 150 flanges. Face to facedimensions in accordance with MSS-SP-68. Valve body rated Class150, ASME B16.34. Seat rated 200 psig @ 400oF. Jamesbury Fig 815L-11-22HB-MT or approved equal. CERTIFICATE OF COMPLIANCE REQUIREDWITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.


TITLE


VALE #SPEC-65050

PAGE

39/58Last Revision

2020/06/15REV.

6

11.15 Cast carbon steel body lug style butterfly valve, lockable, ASTM A216Grade WCB, metal to metal seats, carbon steel disc, Type 316 stainlesssteel shaft, plain type stuffing box with PTFE “V” packing, handwheelgear operated, bolting lugs drilled and tapped for installation with capscrews, suitable for mounting between two Class 125 flanges, flat face,ASME B16.1. Valve body rated Class 150 ASME B16.34. Seat rated200 psig @ 400 oF. Fisher Continental A41 Butterfly, MG Series orequal. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER.

CURRENTLY NOT IN USE IN THE IPC PLANT.

11.17(Added 6504-.01.01.611,

Ver.1)

Cast carbon steel wafer style butterfly valve, lockable, ASTM A216Grade WCB body, 316 stainless steel disc, 17-4PH stainless steel shaft,PTFE V-ring packing, PTFE seat, c/w lever operator. Valve to besuitable for mounting between two Class 150 flanges. Valve body ratedClass 150, ASME B16.34. Seat rated 200 psig @ 400 oF. Tufline *-801-667-TT-ST1-L or approved equal. CERTIFICATE OF COMPLIANCE REQUIREDWITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

11.18(Added 6504-.01.01.611,

Ver.1)

Cast carbon steel lug style steam jacketed butterfly valve, lockable,ASTM A216 Grade WCB body, 316 stainless steel disc, 17-4PHstainless steel shaft, graphite packing, ST2 teflon seat, c/w handwheelgear operator. Valve to be suitable for mounting between two Class 150flanges. Valve body rated Class 150, ASME B16.34. Seat rated 200 psig@ 400 oF. Xomox Pliaxseal *-811-STJ-2-6-7-ST2-G or approved equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

11.19(Added 6504-.01.01.611,

Ver.1)

Cast carbon steel lug style butterfly valve, lockable, ASTM A216 GradeWCB body, 316 stainless steel shaft and disc, graphite packing, filledgraphite seat. Lever handle for sizes 8” and under, gear operated 10”and over, body provided with bolting lugs tapped for installation with capscrews. Valve to be suitable for mounting between two Class 150flanges. Face to face dimensions in accordance with MSS-SP-68. Valvebody rated Class 150, ASME B16.34. Seat rated 200 psig @ 400oF.Jamesbury Fig 815L-11-2236-MT or equal. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.


TITLE


VALE #SPEC-65050

PAGE

40/58Last Revision

2020/06/15REV.

6

16.0 SECTION 12 – SPECIAL VALVES

ITEM NO. DESCRIPTION12.8 Cast or wrought carbon steel flush bottom tank valve, lockable, ASTM

A216 Gr. WCB or ASTM A234 Gr. WPB, 45 degree discharge, 12-13%chromium trim and stem, O.S.&Y., rising stem, plug recedes into valvebody, flanged Class 150, raised face, ASME B16.5.

12.9 Wafer style knife gate valve, lockable, 304 stainless steel wetted parts,stainless steel rising stem, metal seated, round port, TFE impregnatedasbestos packing, handwheel operated, raised face flanges drilled andtapped to match Class 150 flange, ASME B16.5. Rated for 150 PSIGCWP non-shock working pressure. Dezurik 800WCLHG or equal.

12.10 Wafer style knife gate valve, lockable, 304 stainless steel wetted parts,stainless steel rising stem, metal seated, round port, TFE impregnatedasbestos packing, double acting pneumatic cylinder operated, raisedface flanges drilled and tapped to match Class 150 flange, ASME B16.5.Rated for 150 PSIG CWP non-shock working pressure. Dezurik800WCCCGC10 or equal.

12.11(Added 6504-.01.01.611,

Ver.1)

Ductile iron open short body pinch valve, lockable, Linatex (NaturalRubber) sleeve, handwheel operated, flange dimensions to suit matingwith Class 150 flange, ASME B16.5. Sleeve rated 150 PSIG. @ 200 oF.Jaco Type ST.

12.12(Added 6504-.01.01.611,

Ver.1)

Ductile iron open short body pinch valve, lockable, EPDM sleeve,handwheel operated, flange dimensions to suit mating with Class 150flange, ASME B16.5. Sleeve rated 150 PSIG @ 300 oF. Jaco Type ST.

12.13(Added 6504-.01.01.611,

Ver.1)

Ductile iron open long body pinch valve, lockable, Linatex (NaturalRubber) sleeve, handwheel operated, flange dimensions to suit matingwith Class 150 flange, ASME B16.5. Sleeve rated 150 PSIG @ 200 oF.Jaco Type ST.

12.14(Added 6504-.01.01.611,

Ver.1)

Ductile iron open long body pinch valve, lockable, EPDM sleeve,handwheel operated, flange dimensions to suit mating with Class 150flange, ASME B16.5. Sleeve rated 150 PSIG @ 300 oF. Jaco Type ST.

12.15(Added 6504-.01.01.611,

Ductile iron enclosed short body pinch valve, lockable, Linatex (NaturalRubber) sleeve, pneumatic or hydraulic operated, flange dimensions tosuit mating with Class 150 flange, ASME B16.5. Sleeve rated 100 PSIG


TITLE


VALE #SPEC-65050

PAGE

41/58Last Revision

2020/06/15REV.

6

Ver.1) @ 200 oF. Jaco Type RT.12.16

(Added 6504-.01.01.611,

Ver.1)

Ductile iron enclosed short body pinch valve, lockable, EPDM sleeve,pneumatic or hydraulic operated, flange dimensions to suit mating withClass 150 flange, ASME B16.5. Sleeve rated 100 PSIG @ 300 oF. JacoType RT.

12.17(Added 6504-.01.01.611,

Ver.1)

Ductile iron enclosed long body pinch valve, lockable, Linatex (NaturalRubber) sleeve, pneumatic or hydraulic operated, flange dimensions tosuit mating with Class 150 flange, ASME B16.5. Sleeve rated 100 PSIG@ 200 oF. Jaco Type RT.

12.18(Added 6504-.01.01.611,

Ver.1)

Ductile iron enclosed long body pinch valve, lockable, EPDM sleeve,pneumatic or hydraulic operated, flange dimensions to suit mating withClass 150 flange, ASME B16.5. Sleeve rated 100 PSIG @ 300 oF. JacoType RT..

12.19(Added 6504-.01.01.611,

Ver.1)

Ductile iron enclosed long body pinch valve, lockable, Linatex (NaturalRubber) sleeve, manually operated, flange dimensions to suit matingwith Class 150 flange, ASME B16.5. Sleeve rated 100 PSIG @ 200 oF.Jaco Type RT.

12.20(Added 6504-.01.01.611,

Ver.1)

Ductile iron enclosed long body pinch valve, lockable, EPDM sleeve,manually operated, flange dimensions to suit mating with Class 150flange, ASME B16.5. Sleeve rated 100 PSIG @ 300 oF. Jaco Type RT.

12.21(Added 6504-.01.01.611,

Ver.1)

Ductile iron enclosed short body pinch valve, lockable, Linatex (NaturalRubber) sleeve, manually operated, flange dimensions to suit matingwith Class 150 flange, ASME B16.5. Sleeve rated 100 PSIG @ 200 oF.Jaco Type RT.

12.22(Added 6504-.01.01.611,

Ver.1)

Ductile iron enclosed short body pinch valve, lockable, EPDM sleeve,manually operated, flange dimensions to suit mating with Class 150flange, ASME B16.5. Sleeve rated 100 PSIG @ 300 oF. Jaco Type RT.


TITLE


VALE #SPEC-65050

PAGE

42/58Last Revision

2020/06/15REV.

6

17.0 SECTION 13 – BALL VALVES

ITEM NO. DESCRIPTION13.5 This valve is no longer available, IPC currently uses Item 13.24.

13.6(Added 6504-.01.01.611,

Ver.1)

Stainless steel segment ball valve, lockable, ASTM A351 Grade CF8M,AISI Type 329 segment, AISI Type 329 pin and shaft, Nelalloy seat,PTFE seals, manual gear operator, flanged Class 300, raised face,ASME B16.5, body rated 515 psig @ 400oF. Metso Neles R-Series, orapproved equal.

13.7(Added 6504-.01.01.611,

Ver.1)

Stainless steel segment ball valve, lockable, ASTM A351 Grade CF8M,AISI Type 329 segment, AISI Type 329 pin and shaft, Nelalloy seat,PTFE seals, manual gear operator, flanged Class 150, raised face,ASME B16.5, body rated 195 psig @ 400oF. Metso Neles R-Series orapproved equal.

13.20 Fabricated carbon steel body dual pump discharge valve, lockable, twoinlet, single outlet, neoprene lined, ball and ball race designed to permitball to roll from one seat to the other based on pump operationselection, flanged, raised face, Class 150, ASME B16.5. TechnequipLimited, Tech-Taylor Valve T-2 Series. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

CURRENTLY NOT IN USE IN THE IPC PLANT.

13.21(Added 6504-.01.01.611,

Ver.1)

Cast stainless steel ball valve, lockable, ASTM A351 Grade CF8M, 316stainless steel ball and stem, Reinforced Teflon seat and seals, fullopening port, lever operated, flanged Class 150 ASME B16.5. Kitz150UTBM or equal. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

13.22(Added 6504-.01.01.611,

Ver.1)

Cast stainless steel ball valve, lockable, ASTM A351 Grade CF8M, 316stainless steel ball and stem, Reinforced Teflon seat and stem seals, fullopening port, lever operated, VCO “O” ring face seal connections.Whitey “60 series” Model No. SS-6*TVOC*. No substitute. CERTIFICATEOF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.


TITLE


VALE #SPEC-65050

PAGE

43/58Last Revision

2020/06/15REV.

6

13.23(Added 6504-.01.01.611,

Ver.1)

Cast stainless steel ball valve, lockable, ASTM A351 Grade CF8M, 316stainless steel ball and stem, Reinforced Teflon seat and seals, fullopening port, lever operated, threaded ASME B1.20.1, 600 psi @ 350oF minimum rating. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

13.24(Added rev 3,revised rev 6)

Forged brass ball valve, ASTM B124 body, chrome plated brass ball,PTFE seats & seals, full port, lever operated, threaded ends to ASMEB1.20.1, minimum rating of 500 psig at 100oF in accordance with MSS-SP-110 CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER


TITLE


VALE #SPEC-65050

PAGE

44/58Last Revision

2020/06/15REV.

6

18.0 SECTION 14 – STEAM TRAPS

14.1(Added rev 3)

Cast iron steam trap ASTM A126 Class B, inverted bucket type, integralstrainer, trim and strainer as per Manufacturer’s standard for steamservice, screwed ends to ASME B1.20.1, 250# SSP. Strong Series 140-S with tapped blowdown plug. CERTIFICATE OF COMPLIANCE REQUIREDWITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

14.2(Added rev 3)

Cast iron steam trap ASTM A126 Class B, inverted bucket, bottom inletwith trim as per manufacturer’s standard for steam service, screwedends to ASME B1.20.1, 250# SSP. Strong Series 42 thru 46 or equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

14.6(Added rev 3)

Cast iron float-thermostatic steam trap ASTM A126 Class B, Stainlesssteel float, thermodynamic type air vent, trim as per manufacturer’sstandard for steam service, screwed ends to ASME B1.20.1, body rating250# SSP suitable for steam pressure of 175 psig. Sarco Canada LTD,Type FTD or equal. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

14.7(Added rev 3)

Cast carbon steel steam trap ASTM A216 Gr. WCB, inverted buckettype integral strainer, trim and trainer per Manufacturer’s standard forsteam service, screwed ends to ASME B1.20.1, rated 600 psig. StrongSeries 1643-S with tapped blowdown plug. CERTIFICATE OF COMPLIANCEREQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATION NUMBER.

14.8(Added rev 3)

Cast carbon steel steam trap ASTM A126 Gr. WCB, inverted buckettype, bottom inlet with trim as per Manufacturer’s standard for steamservice, screwed ends to ASME B1.20.1, rated 400 psig @ 850°F.Strong Series 640 or equal. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

14.16(Added rev 3)

Stainless steel impulse trap, 10 to 600 psig, screwed ends to ASMEB1.20.1Sarco Canada Ltd. (TD-50 TDC or approved equal). CERTIFICATEOF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

14.17(Added rev 3)

(cast / ductile) iron float thermostatic steam trap, stainless steel float,thermodynamic type air vent, trim as per manufacturer’s standard forsteam service, screwed ends to ASME B1.20.1, body rating 175 psig @380°F. FT14C or approved equal.


TITLE


VALE #SPEC-65050

PAGE

45/58Last Revision

2020/06/15REV.

6

19.0 SECTION 15 – STRAINERS

ITEM NO. DESCRIPTION15.1 Cast iron strainer, ASTM A126 Class B, y-pattern, stainless steel or

monel screen with perforations suitable for steam, steam condensate,water and liquid services, complete with blow-off connection, threadedASME B1.20.1, rated 250# SSP. Spirax Sarco Model YS or equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

15.2(Added 6504-.01.01.611,

Ver.1)

Cast carbon steel strainer, ASTM A216 Grade WCB, y-pattern, stainlesssteel or monel screen with perforations suitable for steam, steamcondensate, water and liquid services, complete with blow-offconnection, threaded ASME B1.20.1, rated 600# SSP minimum. SpiraxSarco Model CT or equal. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

15.6 Cast iron strainer, ASTM A126 Class B, y-pattern, stainless steel ormonel screen with perforations suitable for steam, steam condensate,water and liquid services, complete with blow-off connection, flangedClass 125, ASME B16.1, rated 100# SSP minimum. Spirax Sarco ModelCI-125/F-125 or equal. CERTIFICATE OF COMPLIANCE REQUIRED WITHREFERENCE TO THE CANADIAN REGISTRATION NUMBER.

15.19 Cast steel strainer ASTM SA 216 Gr WC B, Y-pattern, stainless steel1/8” perforated screen, strainer cover shall be blind flange with no blow-down connection, flanged Class 600, raised face, ASME B16.5. SpiraxSarco Canada Ltd. Type YF-600 or approved equal. CERTIFICATE OFCOMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER.

15.20 Cast carbon steel strainer, ASTM A216 Gr. WCB, Y-pattern, stainlesssteel screen, 0.045” perforations for Process Liquid Service. Strainercover shall be blind flange with no blow-down connection, flanged Class300, raised face, ASME B16.5. Meuller Fig 762-0.045 or approvedequal. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER.

15.22 Cast carbon steel strainer, ASTM A216 Gr. WCB, Y-pattern, stainlesssteel screen, 0.045” perforations for Process Liquid Service. Strainercover shall be blind flange with no blow-down connection, flanged Class


TITLE


VALE #SPEC-65050

PAGE

46/58Last Revision

2020/06/15REV.

6

150, raised face, ASME B16.5. Meuller Fig 761-0.045 or approvedequal. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THECANADIAN REGISTRATION NUMBER.

15.29 Cast carbon steel strainer, ASTM A216 WCB, y-pattern, stainless steelscreen with perforations suitable for Process Gas Service. Strainercover shall be blind flange with no blow down connection, flanged Class300, raised face, ASME B16.5. Leslie no. 7203 or approved equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

NOT LISTED IN SERVICE SPECIFICATION


TITLE


VALE #SPEC-65050

PAGE

47/58Last Revision

2020/06/15REV.

6

20.0 SECTION 17 – HOSE

ITEM NO. DESCRIPTION17.5 Light duty rubber hose for slurry service, synthetic SBR rubber tube,

textile reinforcement, SBR cover, 316 SS female cam and groovecoupler each end. Hose assembly rated 100 PSIG at 100 Deg. F.Goodall N-325LD or equal.

17.6 Rubber dry materials handling hose, ¼” thick natural rubber tube,synthetic fabric with helical steel wire reinforcement, SBR corrugatedrubber cover, split aluminum flanges drilled to match Class 150 flanges,ASME B16.5. Hose assembly rated 150 PSIG at 100 Deg. F. GoodallGoodflex or approved equal.

17.21 Rubber hose for slurry service, ¼” gum rubber tube, 4-ply cord andhelical steel wire reinforcement, abrasion resistant neoprene cover, builtup integral rubber flange c/w carbon steel back up ring drilled to matchClass 150 flange, ASME B16.5. Hose assembly rated for 300 psi @ 100Deg F. Goodall Material Handling Hose or approved equal.

17.24 Stainless steel flexible corrugated hose, stainless steel type 321 or316L, double stainless steel braid, carbon steel floating flange both endsdrilled to match Class 150 flange, ASME B16.5. Hose assemblypressure rating dependant on size and temperature.

17.27 Rubber hose for aqueous ammonia service, 0.5% ammonia, EPDMtube, textile with steel wire helix reinforcement, EPDM cover, long shankstainless steel fittings, threaded male ends ASME B1.20.1, withstainless steel clamps or bands. Hose assembly rated 150 PSIG at 100Deg. F. Goodall N2427 or equal.

17.28 Rubber hose for slurry service, ¼” thick natural rubber tube, syntheticfabric with helical steel wire reinforcement, SBR corrugated rubbercover, split aluminum flanges drilled to match Class 150 flanges, ASMEB16.5. Hose assembly rated 150 PSIG at 100 Deg. F. Goodall Goodflexor approved equal.

17.29 Rubber hose for slurry service, ¼” gum rubber tube, cord and helicalsteel wire reinforcement, abrasion resistant neoprene cover, built upintegral rubber flange c/w carbon steel back up ring drilled to matchClass 150 flange, ASME B16.5. Hose assembly rated for 100 psi @ 100Deg F. Goodall Material Handling Hose or approved equal.


TITLE


VALE #SPEC-65050

PAGE

48/58Last Revision

2020/06/15REV.

6

17.30 Rubber hose for slurry service, ¼” gum rubber tube, cord and helicalsteel wire reinforcement, abrasion resistant neoprene cover, built upintegral rubber flange c/w carbon steel back up ring drilled to matchClass 150 flange, ASME B16.5. Hose assembly rated for 200 psi @ 100Deg F.

17.31(Added 6504-.01.01.611,

Ver.1)

Rubber hose, Black Chemigum RMA Class B tube, single wire braidreinforcement, yellow carbryn RMA Class A cover, carbon steel femaleJIC swivel end connections. Hose assembly rated and tested for 3000psig @ 250 Deg. F. Hose to be permanently tagged indicating:Manufacturer’s Name½” Dia.Max. Working pressureTest pressure“REACTOR PORT TEST HOSE”Yellow Gauntlet 3000 or approved equal

17.32(Added 6504-.01.01.611,

Ver.1)

Rubber hose, nitrile rubber tube, textile reinforcement, abrasion resistantred PVC/Nitrile cover. Hose assembly rated for 250 psig @ 100 Deg. F.Goodall N60 Longlife or approved equal.

17.33(Added 6504-.01.01.611,

Ver.1)

Stainless steel flexible corrugated hose, stainless steel type 321 or316L, single stainless steel braid, carbon steel female N.P.T. unionseach end, threaded to ASME B1.20.1. Hose assembly pressure ratingdependant on size and temperature. Goodall Annuflex or equal.

17.34(Added 6504-.01.01.611,

Ver.1)

Rubber hose, Black Chemigum RMA Class B tube, single wire braidreinforcement, yellow carbryn RMA Class A cover, carbon steel maleNPT swivel end connections. Hose assembly rated and tested for 1650psig @ 250 Deg. F. Hose to be permanently tagged indicating:Manufacturer’s Name½” Dia.Max. Working pressureTest pressure“PURGE HOSE”Yellow Gauntlet 3000 or approved equal

17.35(Added 6504-.01.01.611,

Ver.1)

Hydraulic hose, seamless elastomer tube, double steel braidreinforcement, synthetic rubber cover, swivel female SAE thread 37o

flare end connections. Rated 2000 psig @ 250 oF. Imperial Eastman.


TITLE


VALE #SPEC-65050

PAGE

49/58Last Revision

2020/06/15REV.

6

17.36(Added 6504-.01.01.611,

Ver.1)

Stainless steel flexible hose, stainless steel type 316L corrugated liner,single stainless steel type 321 braid, stainless steel Swagelok union endfittings. Hose assembly pressure rating dependant on size andtemperature. Swagelok SS-HO * SL* SL*-*. No substitute.

17.37(Added 6504-.01.01.611,

Ver.1)

Stainless steel flexible hose, TFE resin liner, single stainless steel type304 braid, stainless steel type 316 tube adapter end connections for usewith Swagelok fittings. Hose assembly pressure rating dependant onsize and temperature. Swagelok SS-*BHT-*. No substitute.

17.38(Added Rev 5)

Chlorobutyl rubber (CIIR) hose, for steam service, multiple braid hightensile steel wire for reinforcement, corrosion resistance. Hose rated for175 psig at 380 deg. F. Goodall Dante or approved equal. CERTIFICATEOF COMPLIANCE WITH REFERENCE TO CANADIAN REGISTRATION NUMBERVALID IN THE PROVINCE OF ONTARIO.


TITLE


VALE #SPEC-65050

PAGE

50/58Last Revision

2020/06/15REV.

6

21.0 SECTION 19 – GASKETS

ITEM NO. DESCRIPTION19.1 Compressed asbestos gasket, with SBR binder, 1/16” thick, dimensions

to ASME B16.21 unless specified otherwise. ASTM F37 sealability 0.03ml/hr or better. Durabla Black. (No Substitute)

19.2 PTFE gasket, 1/16” thick, ASME B16.21 unless specified otherwise.ASTM F37 sealability 0.02 ml/hr or better. Durabla Durlon 9000 orapproved equal.

19.3(Added 6504-.01.01.611,

Ver.1)

Compressed asbestos gasket, wire reinforced with SBR binder, e bothsides, 1/16” thick. Klingerit K-1000. (No Substitute)

19.4(Added 6504-.01.01.611,

Ver.1)

Compressed asbestos gasket, with SBR binder, 1/8” thick, dimensionsto ASME B16.21 unless specified otherwise. ASTM F37 sealability 0.03ml/hr or better. Durabla Black. (No Substitute)

19.5(Added 6504-.01.01.611,

Ver.1)

Compressed carbon fiber gasket, with Nitrile binder, 1/16” thick,dimensions to ASME B16.21 unless specified otherwise. Klinger SIL4430 or approved equal.

19.6 Compressed non-asbestos gasket with HNBR binder 1/16” thick,dimensions to ASME B16.21 unless specified otherwise. SealX SX2214

19.7 Compressed non-asbestos gasket with HNBR binder 1/8” thick,dimensions to ASME B16.21 unless specified otherwise. SealX SX2214


TITLE


VALE #SPEC-65050

PAGE

51/58Last Revision

2020/06/15REV.

6

22.0 SECTION 20 - JOINT MATERIALS

ITEM NO. DESCRIPTION20.11 Thread sealing compound for use with high pressure steam, gases, oils

and solvents. Never-Seez Corporation. “Nickel Special” Fig. NS-165. Nosubstitute.

20.12 Teflon based thread sealing compound in paste form. Loctite PST withTeflon or equal.

20.13 Flange Insulating sleeves and washers, Mylar, 4000 volts/mil, withsingle or double washers. Advance Products & Systems Inc. or equal.

20.14(Added 6504-.01.01.611,

Rev.1)

Thread sealant teflon tape.

20.15 V-2 Multi Purpose Thread Sealant by Jet-Lube or approved equal.


TITLE


VALE #SPEC-65050

PAGE

52/58Last Revision

2020/06/15REV.

6

23.0 SECTION 21 - BOLTS

ITEM NO. DESCRIPTION21.1 THE IPC PLANT DOES NOT USE ASTM A307 BOLTS

21.2 Stainless steel hex bolt, ASTM A193 Gr. B8M, Class 1, with one semi-finished heavy series carbon steel hex. nut, ASTM A194 Gr. 2H, UNCthreads to ASME B1.1, ASME B18.2.1, and ASME B18.2.2, with Class2A fit on bolts and Class 2B fit on nuts.

21.3 Alloy steel stud bolt, ASTM A193 Gr. B7, threaded full length with twosemi-finished heavy series hex nuts, ASTM A194 Gr. 2H to ASME B1.1and ASME B18.2.2 with Class 2A fit for bolts and Class 2B fit for nuts.

21.4 IPC current practice is not to use washers on piping systems. The use ofwashers must only be done under the authorization of a ProfessionalEngineer.

21.7 THE IPC PLANT DOES NOT USE ASTM A307 BOLTS

21.9 See Item 21.3.

21.10(Added 6504-.01.01.611,

Rev.1)

Alloy steel hex bolt, ASTM A193 Gr. B7, with one semi-finished heavyseries hex nut, ASTM A194 Gr. 2H to ASME B1.1, ASME B18.2.1, andASME B18.2.2 with Class 2A fit for studs and Class 2B fit for nuts.

21.11(Added 6504-.01.01.611,

Rev.1)

Alloy steel hex bolt for low temperature service, ASTM A320 Gr. L7, withone semi-finished heavy series hex nut, ASTM A194 Gr. 7 to ASMEB1.1, ASME B18.2.1, and ASME B18.2.2 with Class 2A fit for bolts andClass 2B fit for nuts. Nuts to meet low temperature requirements inaccordance with ASTM A194, S4.

21.12(Added 6504-.01.01.611,

Rev.1)

Alloy steel stud bolt for low temperature service, ASTM A320 Gr. L7,with two semi-finished heavy series hex nuts, ASTM A194 Gr. 7 toASME B1.1 and ASME B18.2.2 with Class 2A fit for bolts and Class 2Bfit for nuts. Nuts to meet low temperature requirements in accordancewith ASTM A194, S4.


TITLE


VALE #SPEC-65050

PAGE

53/58Last Revision

2020/06/15REV.

6

24.0 SECTION 22 - PURGE FITTINGS (NEW)

ITEM NO. DESCRIPTION22.1

(Added 6504-.01.01.611,

Rev.1)

Carbon steel purge test flange ASTM A105N, Class 600 ASMEB36.10M, threaded to ASME B1.20.1, as per G.M Nelson Ltd. drawing#38494-2 (Vale drawing 75-021-F-A8631 ).

22.2(Added 6504-.01.01.611,

Rev.1)

Carbon steel purge spacer, ASTM SA-516-70, machined to match 1”Class 300 flange, ASME B16.5. In accordance with G.M. Nelsondrawing 38727-1 (Vale drawing 75-021-F-A8627).

22.3(Added 6504-.01.01.611,

Rev.1)


22.4(Added 6504-.01.01.611,

Rev.1)


22.5(Added 6504-.01.01.611,

Rev.1)


22.6(Added 6504-.01.01.611,

Rev.1)

Carbon steel purge spectacle blind, ASTM SA-516-70, machined tomatch 8” Class 600 flange, ASME B16.5. Registration pending.

22.7(Added 6504-.01.01.611,

Rev.1)



TITLE


VALE #SPEC-65050

PAGE

54/58Last Revision

2020/06/15REV.

6

25.0 SECTION 25 - SIGHT FLOW INDICATORS

ITEM NO. DESCRIPTION25.18 Cast carbon steel sight flow indicator, ASTM A216 Gr. WCB, plain

indicator type, high strength tempered dual glass windows, Teflon fibergaskets, flanged Class 600, raised face ASME B16.5, rated 600 psig.Jacoby-Tarbox Style F910HPA-600-DW or equal.

IPC DOES NOT CURRENTLY USE THIS ITEM.

25.19 Cast carbon steel sight flow indicator, ASTM A216 Gr. WCB, plainindicator type, high strength tempered dual glass windows, Teflon fibergaskets, flanged Class 300, raised face ASME B16.5, rated 300 psig.Jacoby-Tarbox Style F910HPA-300-DW or equal.

IPC DOES NOT CURRENTLY USE THIS ITEM.


TITLE


VALE #SPEC-65050

PAGE

55/58Last Revision

2020/06/15REV.

6

26.0 SECTION 30 - MISCELLANEOUS

ITEM NO. DESCRIPTION30.7 Carbon steel wire basket temporary strainer, ASTM A569, 1/8”

perforations, with 40 mesh stainless steel type 304 lining (inside or out),for use with Class 150 flanges, ASME B16.5. Hayward Model 92 orequal.

30.10 Carbon Steel spectacle blind, ASTM A516 Gr. 70 for use with Class 150flanges, ASME B16.5, serrated machine finish. Crane or equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

30.11 Carbon Steel spectacle blind ASTM A516 Gr. 70 for use with Class 300flanges, ASME B16.5, serrated machine finish. Crane or equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

30.12 Carbon Steel spectacle blind ASTM A516 Gr. 70 for use with Class 600flanges, ASME B16.5, serrated machine finish. Crane or equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

30.13(Added 6504-.01.01.611,

Rev.1)

Stainless Steel spectacle blind, ASTM A240 Gr. 304 for use with Class150 flanges, ASME B16.5, serrated machine finish. Material to besolution heat treated for low temperature service. Crane or equal.CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER.

30.14(Added 6504-.01.01.611,

Rev.1)



TITLE


VALE #SPEC-65050

PAGE

56/58Last Revision

2020/06/15REV.

6

30.15(Added 6504-.01.01.611,

Rev.1)


30.18 Carbon steel quick disconnect with shut-off valve in socket and plug,Viton seals, screwed female ends, ASME B1.20.1, 2000 psig minimumpressure rating. Hansen *-HP-* / *-KP-* or approved equal.

30.20 Carbon steel line blind, ASTM A515, Gr. 60, Clydach Type per VALEDrawing 75-010-F-00361.

30.21(Added 6504-.01.01.611,

Rev.1)

Carbon steel quick acting line blind, carbon steel body, ASTM A216 Gr.WCB, grade B7 jack bolts, butt weld ends, carbon steel spectacle plate,ASTM A516 Gr. 70 c/w Viton seals, Class 150, Proquip 2A01-2WW orapproved equal. CERTIFICATE OF COMPLIANCE REQUIRED WITH REFERENCETO THE CANADIAN REGISTRATION NUMBER.

30.22(Added 6504-.01.01.611,

Rev.1)

Carbon steel quick acting line blind, carbon steel body, ASTM A216 Gr.WCB, grade B7 jack bolts, flanged ends, ASME B16.5, carbon steelspectacle plate, ASTM A516 Gr. 70 c/w Viton seals, Class 150, ASMEB16.5, Proquip 2A01-2FF or approved equal. CERTIFICATE OFCOMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIAN REGISTRATIONNUMBER.

30.30 OPERATORS ARE SUPPLIED WITH THE VALVE

30.43 Carbon steel single swivel joint coupling, Nitrile packing, suitable for360° rotation, both ends flanged Class 150, raised face, ASME B16.5,suitable for water service 175 PSIG @ 380oF. Chiksan Style No. 20 orapproved equal.

30.52 Carbon steel wire basket temporary strainer, ASTM A569, 1/8”perforations, with 40 mesh stainless steel type 304 lining (inside or out),for use with Class 300 flanges, ASME B16.5. Hayward Model 92 orequal.

30.53 Carbon steel wire basket temporary strainer, ASTM A569, 1/8”perforations, with 40 mesh stainless steel type 304 lining (inside or out),for use with Class 600 flanges, ASME B16.5. Hayward Model 92 or


TITLE


VALE #SPEC-65050

PAGE

57/58Last Revision

2020/06/15REV.

6

equal.

30.55 IPC DOES NOT CURRENTLY USE THIS ITEM



30.64Added Rev 3

Cast stainless steel ASTM A351-CF8M body Safety Selector Valverated to ASME B16.34. 300 class raised face flanges to ASME B16.5,dimensions to ASME B16.10. Brass, bronze, or copper bearing alloysnot permitted in wetted parts. Valve shall be tagged for ammoniaservice. Anderson Greenwood Part No. SVR-1210F-SSTO. CERTIFICATEOF COMPLIANCE REQUIRED WITH REFERENCE TO THE CANADIANREGISTRATION NUMBER

30.65Added Rev 3

Cast Iron Drip Pan Elbow for use with safety relief valves in steamapplications, ASTM A126 class B 175 psig at 380 deg F.

27.0 APPENDICES

Appendix A: Revision and Transition NotesAppendix B: Keywords


TITLE


VALE #SPEC-65050

PAGE

58/58Last Revision

2020/06/15REV.

6

Appendix A: Revision and Transition Notes

(Revisions are listed in reverse chronological order with most recent revision at the top.Revision notes describe: what was changed, why it was changed, and the plan to implementthe change, including whether changes are retroactive)

Revision 5Added item 17.38 and updated items 19.1, 19.3, and 19.4. Corrected formatting symbolerrors.

Revision 4Added item 5.60

Revision 3Items 6.54, 7.72, 7.73, 7.74. 13.5, 13.6, 13.7, 13.24, 14.1, 14.2, 14.6, 14.7, 14.8, 14.16,14.17, 17.24, 17.33, 30.64, 30.65 added / modified.

Revision 2SealX Gaskets, Items 19.6 and 19.7 added

Revision 1Document format and number changed due to Vale Engineering Document Programchanges in 2011. Previous Standard number 6504.01.01.611 Rev 2.

The Blaw Knox specifications 2360-1-P-2 were originally issued in 1969. The intent of theCCNR IPC Plant Process Piping Engineering Standard 6504.01.01.611, Revision 1 is tocompletely re-examine the service specifications with regard to material availability, currentapplicable code requirements, and current plant practices. As a result, many items havebeen changed, added, or deleted. The title of the specification has also been changed to the“Process Piping System - CCNR IPC Plant - Material Specification”. No attempt has beenmade to revise the original design intent of the Blaw-Knox specifications. In all cases whererevisions have been made, the new material specification is better than or equal to theoriginal.

Appendix B: Keywords

6504.01.01.611

engineering standard specification...

Documents