1312111098

7654321�

If using the Quartet IdeaShare Board Stand,please see the stand’s instruction guide.Then follow the necessary steps in this guide to set up the electronics in theIdeaShare Board.*Note:Tray Mounting Screws are shipped attached to the marker tray mounting plate at the bottom/back of the board.

olloUnpack the f wing components �Connect the RJ45 cable

• Wrap the RJ-45 cable around the cutoutin the marker tray and connect it to theRJ-45 jack in the back of the tray.

�Attach marker tray

• With the bottom of the board facing up,remove the (4) marker tray mountingscrews from the tray mounting plate in the board frame.

• Slide the marker tray onto the frame withthe marker tray bracket over the boardframe. Make sure the RJ45 cable hangsthrough allotted cutout in back of markertray. Align the screw holes in the marker traybracket with the holes in the tray mountingplate by sliding the plate left or right.

• Re-insert the tray mounting screwsthrough the marker tray bracket into thetray mounting plate in the board frame.

�Attach the mounting hanger to the wall

• Determine board location.To positionboard hanger, mark first hole of hanger 9" from outside edge of board and 5/8"from top of board.

• Check that hanger is level and mark otherholes. Drill holes for each hanger in themarked locations using a 1/4" drill bit.

• Insert wall anchors into holes flush with thewall. Insert screws through hanging bracketinto the wall anchors.Tighten firmly.

�Mount board to wall

• With both parts of dual-lock pads connected,remove protective paper from one side ofeach of the two sets of pads.Apply pads tobottom corners on back of board. Remove the remaining protective paper from dual-lock pads.

• Holding the board at an angle, place the channel in the back of the frame over the wall hanger. Lower the board so that it is flushto the wall. Press bottom corners of boardfirmly to wall to adhere dual-lock pads.

�Attach power cord andperipheral cables

• Connect the Power Cord to thePower Adapter.

• Insert the small round plug comingfrom the Power Adapter into the smallround connector at the back of theMarker Tray.

• To use your IdeaShare Board inwhiteboard mode*, connect the maleend of Serial Cable (included) into theserial port on the bottom of theMarker Tray and the other end into anavailable serial port on your computer.

*Note: Set-up for copyboard mode and virtual touchscreen are explained in the User Manual.

�

© 2002 General Binding Corporation. Printed in the USA. All rights reserved.

����Install the software

• Insert the software CD into the CD-ROM drive on your computer.

• The software should start up automatically. If the installer does not start up automatically, browse toyour CD-ROM drive and select thesetup program. Follow all on-screendirections.

• Once the software has been installed,launch the software by double-clickingthe Quartet IdeaShare icon on yourcomputer’s desktop.

�Insert the markers

• Open each electronic pen by pressing the latch located at the top of the pen.

• Insert the dry-erase marker into the corresponding color-coded electronic pen.

• Close the electronic pen.

��If help is needed

• Refer to the troubleshooting sectionin the User Manual or the Help files in the eBeam software.

• GBC Customer Service is also availableat 800-541-0094.

��Complete the QuartetIdeaShare registration

• After installing the software, you willbe connected to the GBC productregistration page, if you are connectedto the Internet.

• If you are not connected to theInternet or choose to register later,simply go to www.GBCOffice.comand click on the Register/Support tabat that time.

• Please fill out all the necessary information to activate your product warranty.

��Learn how to useQuartet IdeaShare

• The User Manual and SoftwareReference Guide contain more information about Quartet IdeaSharefeatures and applications.

• Learn how to save time and moneyusing Quartet IdeaShare to capturenotes and diagrams, collaborate withothers, enhance presentations, andmuch, much more!

�Install batteries in theelectronic pens

• Remove the end cap from each electronic pen by turning it in thedirection of the arrow.

• Insert batteries (included), with theplus (+) side up.

• Replace the end cap.

Install batteries in theelectronic eraser

• Remove the battery cover from theelectronic eraser by twisting a coincounterclockwise in the slot.

• Drop in two batteries (included),plus (+) side up.

• Replace the cover.

68505260www.touchboards.com 205 Westwood Ave.Long Branch, NJ 07740 1-866-942-6273 Sales@touchboards.com