enigma air shower and tub door manual ver 1 rev 4 … air shower door / tub door installation...

ENIGMA AIRSHOWER DOOR / TUB DOOR INSTALLATION INSTRUCTIONS

IMPORTANTDreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your models web page on DreamLine.com

Right hand door installation shown

For more information about DreamLine Shower Doors, Tub Doors & Enclosures, please visit DreamLine.com

ENIGMA AIR manual Ver 1 Rev 4 06/2017 2017 DreamLine. All Rights Reserved

DRAFT

not app

roved f

or relea

se

DRAFT

not app

roved f

or relea

se

This model is treated with DreamLines exclusive ClearMaxTM Glass technology. This is a specially formulated coating that prevents the build up of soap and water spots. Install the surface with the ClearMaxTM label towards the inside of the shower.Please note that depending on the model, the glass may be coated on either one or both surfaces.

For best results, squeegee the glass after each use and dry with a soft cloth.

2ENIGMA AIR manual Ver 1 Rev 4 06/2017

20

17 D

ream

Line

. All

Righ

ts R

eser

ved

MODEL #sSHDR-64487610-##SHDR-64606210-##SHDR-64607610-##

##=finish07- Brushed Stainless steel08- Polished Stainless Steel

NOTE: This door is reversible for right or left-hand door installation. The right-hand door installation is shown as an example throughout this manual. For the left-hand door installation, simply begin on the opposite wall and reverse the orientation of the steps shown.

ENIGMA AIR manual Ver 1 Rev 4 06/2017 3

20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Left-Hand door installation Right-Hand door installation

NOTE: This manual will describe the single threshold shower door installation only.

For the Enigma Air enclosure installation, please refer to the Enigma Air Enclosure manual packaged with the return panel glass.


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

ENIGMA AIR ENCLOSURE

MODEL #sSHEN-6434480-##SHEN-6434600-##

##=finish07- Brushed Stainless Steel08- Polished Stainless Steel

ENIGMA AIR ENCLOSURESHOWER ENCLOSURE INSTALLATION INSTRUCTIONS



ENIGMA AIR ENCLOSURE manual Ver 1 Rev 2 06/2017 2017 DreamLine. All Rights Reserved

Right - Hand return panel installation shown

MODEL #sSHEN-6434480-##SHEN-6434600-##

##=finish07- Brushed Stainless Steel08- Polished Stainless Steel

ENIGMA AIR ENCLOSURESHOWER ENCLOSURE INSTALLATION INSTRUCTIONS



ENIGMA AIR ENCLOSURE manual Ver 1 Rev 2 06/2017 2017 DreamLine. All Rights Reserved

Right - Hand return panel installation shown


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Install studs OR install 2x 6 wood blocking between the studs where the Guide Rail Brackets will attach to the wall

Reinforcement for Enigma Series Heavy Glass frameless sliding shower door

2 X 6

Stud or

thresh

old

or tub

deck

measured from threshold*(see list below)

2 X 6

*Blocking height requirement (to center)as measured from threshold or tub deck:Enigma Air = 73 for shower ht / 59 for tub ht Enigma X = 72-1/2 for shower ht / 58-1/2 for tub htEnigma Z = 73-1/2 for shower ht / 59-1/2 for tub ht Enigma = 75-1/2 for shower ht only

thresh

old

or tub

deck

Preparation

!

1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the Detailed Diagram of Shower Door Components. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 3 business days of the delivery date. Please note that DreamLine will not replace any damaged products or missing parts free of charge after 3 business days or if the product has been installed. Contact DreamLine if you have any questions and please provide an order number, job name or other proof of purchase to help us identify your original order.

2. If this unit is going to be installed in a new construction, install all of the required plumbing and drainage before installing the shower. Use a competent and licensed (if required by local code) plumber for all plumbing installation.

3. Please note that you should consult your local building codes with questions about installation compliance standards. Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project and will not accept any returns.

4. Please make sure that prior to beginning the installation, the surfaces are leveled and solid and will be able to support the total weight of the unit. Also make sure the walls are at right angles. Irregular installation surface level, radius corners or improper angle of side walls will result in serious problems for your installation. Please note that some adjustments and drilling may be necessary during the installation process.

5. Please protect all primary surfaces of the product during installation. Never set your glass down directly onto a tile floor. Leave corner protectors in place until necessary to remove them. Always use a piece of wood or cardboard to protect the bottom edge and corners of the glass prior to and during installation.

6. This unit must be installed upon a finished threshold and against finished walls.

7. This model does NOT have any adjustment for out-of-plumb conditions. Verify that your walls are plumb before proceeding with the installation.

8. This model requires that you drill into the threshold for proper installation.

9. Installation of the Guide Rail brackets into a stud or 2 x 6 wood reinforcement is strongly recommended.

10. This model requires a minimum 2-1/4 of flat threshold space for installation.

11. Professional Installation Required.

NOTE: This manual will describe the shower door installation. Please follow the same sequence of installation steps for the tub door installation.

NOTE: DO NOT attach the handle to the door glass until instructed to do so. DO NOT use the handle to lift the glass during installation. This may result in damage to the glass and/or serious injury. Always use an assistant and/or a professional grade glass suction cup when handling heavy glass panels.


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Tools

NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the detailed diagram and packing list in this manual as a reference. Before discarding the carton, check for small hardware bags that may have fallen to the bottom of the box. If any parts are damaged or missing, please contact DreamLine for replacement. The shipping boxes may contain extra parts not used in your model configuration.

NOTE: Retain these installation instructions for future reference.


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

SiliconeTapeMeasureLevel

PhillipsScrewdriver

Pencil

W

Top

Middle

Bottom

Tip: Measure the finished opening before proceeding with the installation to be sure that the correct model size has been ordered.

Carpenters Square

DrillPower

(D=1/8")Drill bit

(D=5/16")Drill bit

Painters Tape

HammerSoft Head

Tip: Prior to installation, cover the shower/tub drain with tape to prevent losing screws or small parts.

Metal File

Chop saw and Hacksaw

Professional-grade Glass suction cup

Detailed Diagram of shower door components


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Part# Part#Item Qty Item Qty01 U-channel 1pc

11 Anti-splash Threshold 1pc

02 Stationary Glass 1pc

12 Guide Block 1pc

03 Door Glass 1pc

13 Anti-water side strip 2pcs

04 Guide Rail 1pc

14 Bumper strip 1pc

05 Stopper 2pcs

15 Handle 1set

06 Guide Rail Bracket (6a & 6b) 2pcs

16 5/16 (8mm) plastic wall anchor 7pcs

07 Glass Bracket 2pcs17 ST4.240 countersunk screw 4pcs

08 Roller 2pcs

18 ST4.225 round head screw 1pc

09 Roller Guard 2pcs

19 Allen wrench (4mm) 1pc

10 Threshold End Cap 1pc

Parts List

20 Thread Lock Adhesive 1pc

21 ST4.255 countersunk screw 2pcs

74

89

5

1

13

14

15

16

2

3

18

19

17

1011

12

6 6b6a

20

21The glass surface

with the ClearMax label must be

installed to face inside of the shower

Installation steps


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Fig 1

Fig 2

L

1. Check both of the nished walls for plumb and the threshold for level. (Fig 1)

NOTE: This model does not allow for out-of-plumb adjustment.

2. Using a Chop-saw or a Hack-saw, cut the Guide Rail (#04) to fit the finished opening. Measure the finished opening width at the position of the Guide Rail (#04) for the model height:

for Shower model: Measure the width at a height of 72-1/4 for Tub model: Measure the width at a height of 58-1/4 This will be dimension (L).

The Guide Rail (#04) is 1 less than the model sizeand will need to be cut to 1 less than the finished opening size (L):

Finished opening (L) - 1 = finished cut length

(Fig 2 and Fig 3)

NOTE: The right-hand door installation is shown as an example throughout this manual. For the left-hand door installation, simply begin on the opposite wall and reverse the orientation of the steps shown.


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Fig 4

Fig 3

Finished opening (L) - 1 = finished cut length

2-1/4minimumthreshold space

1/4

1/4

1/4

NOTE: Use a metal file to remove any burrs from the cut end of the Guide Rail (#04).

Metal FileCut from the door end only which is the end opposite of the holes

Guide Rail with the Guide Rail brackets attached

L

3. This model requires a minimum 2-1/4 of flat threshold space for installation. Starting from the wall on the stationary panel side, use a Carpenters Square as a guide and measure in 1/4 from the outside of the threshold and mark the threshold. Extend this line across the threshold to the opposite wall to use as a reference in Step #17. (Fig 4)


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

1

5/16

2 3

4 5

Fig 5

Fig 6

U-Channel

4. Align the edge of the U-Channel (#01) to the inside of the mark on the threshold. Mark the position of the U-Channel (#01) on the wall and mark the four holes for drilling through the pre-drilled holes in the U-channel. (Fig 5)

5. Remove the U-Channel (#01) from the wall and drill the anchor holes using a 5/16 drill bit and insert the Wall Anchors (#16).Add a bead of silicone to the back of the U-Channel (#01) and attach it to the wall using four of the ST4.2 x 40 Countersunk Screws (#17). (Fig 6)


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Fig 3

Fig 4Fig 7

GUIDE RAIL BRACKET HEIGHTMODELHEIGHT h2 =

76" shower 72-1/4"62" tub 58-1/4"

Table 1

Fig 8

Right hand door installation shown as example

h2

outside inside

u-channelGuide RailBracket

1-1/4

h2

72 1

/4

76

1-1/4

58 1

/4

62

1-1/4

h2 h2

u-channel

shower height

tub height

6. To position the Guide Rail Brackets (#06):From inside of the shower, measure up from the threshold to the bottom of the Guide Rail Bracket (#06) using Table 1 below. While holding the bracket against the edge of the installed U-channel (#01), mark the wall at the bottom of the bracket. (Fig 7 and Fig 8)


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Fig 9

Fig 10

6b

6a

15/16"

2 3

The guide block bracket should be centered in the bracket as shown to allow for vertical adjustment both up and down.

CL

(=)

(=)

7. Hold the Guide Rail Bracket (#06) in the marked position and mark the hole for drilling through the Guide Rail Bracket (#06) using a pencil (or center punch). (Fig 9)

8. **Drill a 5/16 anchor hole and insert a Wall Anchor (#16). Separate the Guide Rail Bracket (#06) components (6a and 6b). Install the Guide Rail Wall Bracket (#06b) to the wall using one ST4.2 x 55mm Countersunk Screw (#21). (Fig 10)

*NOTE: Installation of the Guide Rail brackets into a stud or 2 x 6 wood reinforcement is strongly recommended.

**NOTE: When installing to a stud, drill a 1/4 hole and do not use the anchors.


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Fig 12

Fig 11

2

1

3

9. Insert the Stationary Glass (#02) into the installed U-Channel (#01).

Use Caution not to bang the glass into the u-channel or threshold. (Fig 11)

10. Make sure that your Stationary Glass (#02) is parallel to the front edge of the threshold and mark it. Slide the Guide Block (#12) into the notch of the Stationary Glass (#02), and align flush with the edge of the glass. Mark its position on the threshold and also mark the hole for drilling using a pencil (or center punch). (Fig 12)

!


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Fig 13

Part#12 - Guide Block (with caps)

Fig 14

2

*see note

1 use a pencil or a center-punch to mark the hole

** only use anchor with tile threshold3 4

face plate

5M5 X 10

11. Remove the Stationary Glass (#02) from the U-Channel (#01) and carefully set it aside. (Fig 13)

12. To install the Guide Block (#12): Loosen the set screw on the side and remove the guide block face plate. (Fig. 14.5) Apply silicone to the underside of the Guide Block (#12) and screw the Guide Block (#12) to the threshold as described below: *NOTE: For installation into an Acrylic threshold: drill an 1/8(3mm) hole and use the ST4.2 x 25mm Round Head Screw (#18) OR For installation into a Tile threshold:** drill a 5/16(8mm) hole, install Wall anchor 5/16 (#16) and use the ST4.2 x 40mm Countersunk Screw (#17).

Note: For Tub installations: the bottom bracket must be screwed down to the tub deck. (Fig 14)


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Fig 15

Fig 16

1 2 3 4

door endpanel end


TIP: Bring the door glass into the shower before permanently installing the stationary panel glass and guide rail.

13. Apply silicone into the U-Channel (#01). Slide the Stationary Glass (#02) firmly into the installed U-Channel (#01).

Use Caution not to bang the glass into the U-channel or threshold. (Fig 15)

14. Attach the Stoppers (#05) and Guide Rail Brackets (#06) to both ends of the Guide Rail (#04). (Notice that the top of the guide rail bracket has two set screws). (Fig 16)

NOTE: Be careful not to scratch the guide rail with the brackets and stoppers. Loosen the set screws before installation.

!


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

1

Fig 17

Fig 18

2

TIP: Leave the set screws that hold the guide rail to the bracket loose to allow for side to side adjustment of the guide rail to make it easier to align the holes in the guide rail with the holes in the panel glass. Tighten these set screws after the holes are aligned.

15. Attach the Stationary Glass (#02) to the Guide Rail (#04) using the Glass Brackets (#07). (Fig 18)

14. Align the panel end of the Guide Rail (#04) with the installed Guide Rail Wall Bracket (#6b).Slide the Guide Rail Bracket (#6a) over the Guide Rail Wall Bracket (#6b) and tighten the set screws. (Fig 17)


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Fig 19

Fig 20


1-1/4

1-1/4

measure from the plumb line to the edge of the bracket inside the shower

with the guide rail level, mark the bottom position of the bracket on the wall

14. Align the panel end of the Guide Rail (#04) with the installed Guide Rail Wall Bracket (#6b).Slide the Guide Rail Bracket (#6a) over the Guide Rail Wall Bracket (#6b) and tighten the set screws. (Fig 17)

16. Level the Guide Rail (#04) across the opening. If necessary, use the set screws on the Guide Rail Bracket (#06) to adjust the level of the Guide Rail (#04). (Fig 19 and Fig 20)

17. Using the mark on the door side of the threshold from Step #3, draw a plumb line up the wall on the door side of the opening. Measure over 1-1/4 into the shower from this line. With the Guide Rail (#04) level, mark the position of the Guide Rail Bracket (#06) on the wall. (Fig 20)


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

NOTE: Be careful not to scratch the upper rail while sliding the brackets onto the guide rail.

6b

6a

Fig 21

Fig 22

3*5/16 2 41

1 2 3

4 5 6

18. Remove the Guide Rail (#04) from the Stationary Panel Glass (#02). Remove the Guide Rail Bracket (#06) from the Guide Rail (#04) and hold it back in position on the wall and mark the anchor hole. Drill a 5/16 hole and insert a Wall Anchor (#16). Separate the Guide Rail Bracket (#06) components (6a and 6b). Attach the Guide Rail Wall Bracket (#06b) to the wall using one ST4.2 x 55mm Countersunk Screw (#21). (Fig 21)

19. Re-attach the Guide Rail (#04) to the Stationary Glass (#02) and attach the Guide Rail Brackets (#06). (Fig 22)

*NOTE: Installation of the Guide Rail brackets into a stud or 2 x 6 wood reinforcement is strongly recommended.


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Fig 23

20. Re-check the Guide Rail (#04) for level and if necessary, adjust with the set screws on the Guide Rail Brackets (#06). (Fig 23)


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

L

Fig 24

1 2 43

Fig 25Right hand door installation shown as example

L

22. Apply silicone to the bottom of the Anti-Splash Threshold (#11). Remove the face plate from the Guide Block (#12). Insert one end of the Anti-Splash Threshold (#11) fully into the Guide Block (#12) and replace the guide block face plate. Align the Anti-Splash Threshold (#11) parallel with the front edge of the shower base or threshold. Cover the other end of the Anti-Splash Threshold (#11) with the Threshold End Cap (#10). Apply a small amount of silicone onto the threshold and the wall to prevent leakage. (Fig 25)

21. Measure the distance from the edge of the Guide Block (#12) to the wall. This distance will be (L).Cut the Anti-Splash Threshold (#11) to the size of: (L). (Fig 24)


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Painters Tape

Fig 26


Fig 27

Rotate disk to adjust

insideHandle holes

24. Attach the Rollers (#08) to the Door Glass (#03) with the wheels facing out. NOTE: The roller hardware disk can be rotated to tilt the door glass slightly to create a tight seal with the wall. Make any adjustments after all of the vinyl seals are installed. (Fig 27)

NOTE: DO NOT install the handle onto the door glass until instructed to do so. DO NOT attempt to lift the glass using the handle. This could result in damage to the glass and/or serious personal injury. Always use an assistant or a professional grade glass suction cup when handling heavy glass.

23. Temporarily secure the Anti-Splash Threshold (#11) to the threshold with several pieces of painters tape to hold it in position tight to the threshold until the silicone fully cures. (Fig 26)

NOTE: Apply Thread Lock (#20) to the roller bolts during installation.

!


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Fig 29

Fig 28

1

3

2

3

2 inside

1inside

outside

25. Align the bottom of the Door Glass (#03) with the Guide Block (#12) and hang the door from the Guide Rail (#04). (Fig 28)

26. Install the Roller Guards (#09) onto the Door Glass (#03) so that the longer section extends beneath the Guide Rail (#04). Use a small allen wrench to hold the shorter part of the roller guard and rotate the larger section so that there is approximately 1/16 of clearance between the Roller Guards (#09) and the Guide Rail (#04). (Fig 29)

NOTE: Apply Thread Lock (#20) to the Roller Guard bolt during installation.


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

Door

To secure the Stopper (#05):Apply the Thread Lock Adhesive (#20) to the threads of the set screws during the final installation. Fully tighten the set screws with the supplied allen wrench.

Stopper

Thread Lock Adhesive

Fig 31

1 2

3 4

Fig 30

Door

Panel

Panel

***Position the panel-side stopper no less than 4-1/2 from the wall to allow proper clearance for the handle***

28. To position the Stoppers (#05), remove the set screws from the Stoppers (#05) and apply Thread Lock Adhesive (#20) to the threads. Re-insert the set screws into the Stoppers (#09) and screw them tightly to the Guide Rail (#04). (Fig 31)

27. Attach the Handle (#15) to the Door Glass (#03).Attach the Anti-Water Strips (#13) to the edge of the Stationary Panel Glass (#02) and Door Glass (#03). Attach the Bumper Seal Strip (#14) to the handle side of the Door Glass (#03). (Fig 30)

NOTE: Cover the shower/tub drain with tape prior to removing the set screws to prevent loss.

NOTE: The Stoppers (#05) must be positioned correctly to prevent the handle from contacting the Stationary Glass (#02) and to stop the Door Glass (#03) in a position that allows the bumper strip to create a seal with the wall, but does not allow the door glass to bang into the wall.


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

24Hours

Fig 32

29. Apply good quality mildew-resistant silicone along the connection of the stationary glass with the walls and the threshold. Allow 24 hours for the silicone to fully cure before using the shower. (Fig 32)

NOTE: To maximize the life of your door, it is important to regularly inspect the glass and other hardware for misalignment, proper attachment, and/or damage. Contact DreamLine with any questions or concerns.

Product Maintenance

BASES and BACKWALLS: To ensure a long life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.

GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth. Rinse and wipe off the glass using either a soft cloth or a squeegee to prevent soap buildup and water spots (Hard water can etch the surface of the glass over time if left to dry). To prevent scratching the surface: never use abrasive cleaners and cleaning products that contain scouring agents. Never use bristle brushes or abrasive sponges.

HARDWARE: To ensure a long lasting finish: wipe off the metal parts after each use with a soft cloth. Do not use abrasive cleaners or cleaning products containing ammonia, bleach or acid. If accidentally used, rinse the surface as soon as possible to prevent finish peeling or corrosion. After cleaning the shiny finishes, rinse thoroughly and wipe dry with soft cloth. Clean stainless steel surfaces at least once a week. When applying stainless steel cleaner or polish, work with (not across) the grain. Never use abrasive sponge or cloth, steel wool or wired brushes as these may permanently scratch the surface.

DreamLine shower doors are designed not to leak under normal usage when installed properly, and the water flow is not pointed directly at the vinyl seals or wall-mounted hardware.


20

17 D

ream

Line

. All

Righ

ts R

eser

ved

enigma air shower and tub door manual ver 1 rev 4 … air shower door / tub door installation...

Documents

ENIGMA SKY Shower and Tub Door Manual Ver 1 Rev 2 062019 › Installation_Manuals › ENIG… · For more information about DreamLine® Shower Doors, Tub Doors & Enclosures, please

ARE YOU A PROFESSIONAL INSTALLER?pdf.lowes.com/installationguides/849388002707_install.pdf · INFINITY-Z SHOWER DOOR / TUB DOOR INSTALLATION INSTRUCTION IMPORTANT DreamLine® reserves

SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS · 2015. 11. 14. · CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT ... 09 Decorative cover for Guide block 6pcs NOTE: Carefully

ENIGMA SKY Shower and Tub Door Manual Ver 1 Rev 1 022018pdf.lowes.com/installationguides/849388061186_install.pdfENIGMA SKY SHOWER AND TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT

Aqua Fold Shower Door & Basepdf.lowes.com/installationguides/849388056694_install.pdf · 2020-04-23 · For more information about DreamLine® Shower Doors, Tub Doors & Enclosures,

SHOWER / TUB DOOR INSTALLATION INSTRUCTIONS · 2017. 4. 17. · “VITREO X” manual Ver.2 Rev.4 04/2016 5 Shower/Tub Door Installation Attention: This shower/tub installation is

ENIGMA SKY Shower and Tub Door Manual Ver 1 Rev 1 022018pdf.lowes.com/installationguides/849388063081_install.pdf · 2019-04-26 · ENIGMA SKY SHOWER AND TUB DOOR INSTALLATION INSTRUCTIONS

irp-cdn.multiscreensite.com › 94dcc67c › files › ... · Tub/Shower Shower Door/Rail/Curtain Sink/Faucets Plumbing/Drains Exhaust Fan Towel Rack(s) ... THIS SECTION TO BE COMPLETED

SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS · 2015-09-27 · CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign

FRAMED SLIDING DOOR FOR TUB OR SHOWER - The Home Depot · PDF fileFRAMED SLIDING DOOR FOR TUB OR SHOWER INSTALLATION INSTRUCTIONS QCI0023 . MAINTENANCE: ... no small hardware parts

INFINITY-Zpdf.lowes.com/installationguides/849388055512_install.pdfINFINITY-Z SHOWER DOOR / TUB DOOR INSTALLATION INSTRUCTION IMPORTANT DreamLine® reserves the right to alter, modify

TUB AND SHOWER DOORS 2016 - Empire Industriesempire-industries.com/.../12/Empire-Shower-Doors.pdf · • Advanced fully frameless by-pass door design • 2 sliding glass doors with

Shower Door Hardware - Amazon S3€¦ · Shower Door Hardware. Index Shower Hinges Shower Door Knobs Shower Door Pull Handles Shower Door Polycarbonates Page 1-4 5 6-7 8. 1 Classic

€¦ · BYPASS TUB & SHOWER Enclosures Exposed Roller, Frameless Sliding Door Rail System Transcend TRBSE bypass shower slider with chrome finish and standard four roller & ProLoc

DRAFT-ENCORE Shower and Tub Door Manual Ver 1 Rev 6 …

ENIGMA SKY Shower and Tub Door Manual Ver 1 Rev 1 022018

ENCORE Shower and Tub Door Manual Ver 1 Rev 7a 112020

FRAMELESS SLIDING DOOR FOR TUB OR SHOWER · FRAMELESS SLIDING DOOR FOR TUB OR SHOWER QCI5019 Rev 0 Page 1 Certified 06/21/2016. Lysol Although safety tempered glass is very resistant

Tub & Shower Repair · 2017. 11. 17. · Tub & Shower Repair . Bañera y Ducha Reparación • Featuring a comprehensive line of tub spouts, single lever escutcheons, shower heads,

Shower and Tub/Shower Enclosures, Bathtubs with …mirobase.iapmo.org/standards/standards/5555.pdf · IAPMO IGC 154‐2016 Shower and Tub/Shower Enclosures, Bathtubs with Glass Pressure‐Sealed

Aqua Ultra Shower Door & Base Kitpdf.lowes.com/installationguides/849388008952_install.pdf“AQUA ULTRA” Rev.2 Ver.1 07/13 4 Shower and Tub Door Installation 1. Place the U-Channel

TUB & SHOWER FAUCET TRIM

SHOWER/TUB DOOR INSTALLATION INSTRUCTIONSVer. 2, Rev. 1 CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products

EXPRESSIONS SLIDING DOOR SHOWER AND TUB … INSTALLATION... · EXPRESSIONS SLIDING DOOR SHOWER AND TUB ENCLOSURES 3 Industrial Drive, Vernon, NJ 07462 973-209-4141 fax 973-209-7621

DreamLine Showers : DreamLine Duet Shower Door & Tub Door ... · DUET manual Ver.1 Rev 15 11/2016 DUET SHOWER DOOR/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves

ESSENCE Shower and Tub Door Manual Ver 1 Rev 2 a 082018 · 2021. 1. 29. · ESSENCE SHOWER / TUB DOOR INSTALLATION INSTRUCTIONS model#s SHDR-6348760-## SHDR-6360760-## For more information

Charisma Shower Door & Base Kit - s3.amazonaws.com · Ver. 2, Rev. 1 CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or

DreamLine Showers : DreamLine Charisma Shower Door Manual · model: CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or

HOWER DOOR & TUB DOOR INSTALLATION … SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS ##=finish 07- Brushed Stainless Steel 08- Polished Stainless Steel IMPORTANT DreamLine® reserves

ESSENCE Shower and Tub Door Manual Ver 1 Rev 1.1 052017 · 2018-07-24 · ESSENCE Shower / Tub Door Installation Instructions model#s SHDR-6348760-## SHDR-6360760-## IMPORTANT DreamLine®

TUB DOOR AND TUB DOOR GLASS PANEL INSTALLATION …pdf.lowes.com/installationguides/849388010153_install.pdf · Tub Door Glass Panel Installation Instructions ... Place the Glass door

NeoN - gutstein.co.il · A5578 Concealed shower mixer 12 BaTh TuB/shower. A5575 Exposed shower thermostat A5576 Exposed tub thermostat 13. A5580 Concealed tub thermostat 14. A5584

ENIGMA X Shower and Tub Door Manual Ver 6 Rev 7 072018ENIGMA-X SHDR-61727610-## SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign

House Plans and Home Design. House Plan Symbols Wall: Window: Door: Shower: Tub: Toilet:

VISIONS - Lowe'spdf.lowes.com/installationguides/815324013885_install.pdf · 2019. 3. 21. · VISIONS Ver 1 Rev 7 07/2015 1 VISIONS SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS