enviro ef2 classic wood pellet fire fpi cb and fs cb · 2 stainless steel inner liner ø75mm x...

9
November 2011 Enviro EF2 Classic Wood Pellet Fire FPI CB and FS CB Classic Wood Pellet Burning Heater Insert and Free Standing Models Installation Specifications Safety testing of the EF2 Classic FS CB Pellet Burning Heater to AS/NZS 2918, ARS 09/1981 & 08/1902. Emissions 07/1731 Safety testing of the EF2 Classic FPI CB Pellet Burning Heater to AS/NZS 2918, ARS 09/1981 & 09/1952, 09/1953. Emissions 07/1713 Flue Kit Testing to AS/NZS 2918 AppF: 05/1185

Upload: others

Post on 24-Jun-2020

2 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Enviro EF2 Classic Wood Pellet Fire FPI CB and FS CB · 2 Stainless steel inner liner ø75mm x 900mm long 5 8 Rain cap 75mm 1 12 T-adaptor/cleanout – ø75mm 1 16 Clamp – ˜exible

November 2011

Envi

ro E

F2 C

lass

icW

ood

Pelle

t Fire

FPI

CB

and

FS

CB

Classic Wood Pellet Burning HeaterInsert and Free Standing Models

Installation SpecificationsSafety testing of the EF2 Classic FS CB Pellet Burning Heater to

AS/NZS 2918, ARS 09/1981 & 08/1902. Emissions 07/1731

Safety testing of the EF2 Classic FPI CB Pellet Burning Heater to AS/NZS 2918, ARS 09/1981 & 09/1952, 09/1953. Emissions 07/1713

Flue Kit Testing to AS/NZS 2918 AppF: 05/1185

Page 2: Enviro EF2 Classic Wood Pellet Fire FPI CB and FS CB · 2 Stainless steel inner liner ø75mm x 900mm long 5 8 Rain cap 75mm 1 12 T-adaptor/cleanout – ø75mm 1 16 Clamp – ˜exible

2

November 2011

InstallationDimensions – Classic Freestanding

Dimensions - Classic Insert & Built-In Heater

597 mm

525 mm 556 mm

767 mm

FPI (612 mm)

333 mm559 mm

FPI579 mm

Page 3: Enviro EF2 Classic Wood Pellet Fire FPI CB and FS CB · 2 Stainless steel inner liner ø75mm x 900mm long 5 8 Rain cap 75mm 1 12 T-adaptor/cleanout – ø75mm 1 16 Clamp – ˜exible

3

November 2011

Installation Clearances & SpecificationsMinimum clearances shown are in millimetres. All Enviro fires are tested to AS/NZS2918:2001. Specifications were correct at time of printing but may alter and those detailed below should be used as a guide only. Refer to the Installation and Operation Manual supplied with every Enviro Pellet Fire or if in doubt, consult your Switch Retailer. Refer to Safety Test 09/1981 for all clearances to combustibles.

Clearances to Combustibles

Internal Flue (Freestanding)

Built-In Fire and Flue

Internal Flue

External Flue (Freestanding)

B

C

A E

D

Clearances to CombustiblesClassic Pellet Fire(built-in & freestanding)

Freestanding Clearances

Built-In Heater Clearances

G

F

B

FG

E

B

J

H

AE

J

J

F

B

I F

E

Location Dimension (mm)

A 100

B 150

C* 50

D ~210

E N/A

F 75

G* 50

H 100

I* 50

J* 25

Location Dimension (mm)

K 100

L 920

M# 1020

N 150

O# 150

P* 50

NOTE: Built-In fire clearances don’t apply in a non-combustible cavity. However, remember you will need access for servicing. The above clearance to combustibles on the flue are only applicable within the fire envelope. Clearance outside this e.g.at a ceiling / wall thimble reverts to 25mm as per ARS flue test 05/1185. Correct as at November 2011. # Fire hearth width indicative only. Critical measurement is “O”, extending in front of the fire. Hearth width only needs to be same as fire width.

* from shielded flueNote: AS/NZS 2918 requires a minimum of 100mm clearance for any side requiring access.Note: These are minimum clearances to combustibles. Actual installation distances may be greater.

WA

LL WA

LL WA

LL WA

LL WA

LL WA

LL WA

LL

KL WALL WALL WALL WALL WALL WALL WALL WALL

N

M

P

O

Page 4: Enviro EF2 Classic Wood Pellet Fire FPI CB and FS CB · 2 Stainless steel inner liner ø75mm x 900mm long 5 8 Rain cap 75mm 1 12 T-adaptor/cleanout – ø75mm 1 16 Clamp – ˜exible

4

November 2011

Location of the Pellet Fire

Installation of the Enviro Classic Wood Pellet Burning Heater should be undertaken by an experienced installer. Please read the Classic Owners/Technical Manual thoroughly before commencing installation as failure to follow the instruction could cause damage to the pellet fire or property.

Positioning the fire:

Generally the Classic should be installed in a centrally located position within the home. When deciding where to position the appliance in your room you need to consider the following:

• Location of a power source

• The Classic has a convection fan which blows air through tubes in the direction that the fire faces, for optimum performance this location should be in a large room centrally located.

• The Classic must be installed on a non-combustible surface. This surface must protrude 150mm from the front of the closed pellet fire door.

• The Classic has been Safety Tested to AS/NZS 2918 using the Davins manufactured flue. Test Report ARS 05/1185. Installation is not exclusive to these nominated kits, though alternative flue should only be considered following consultation with your local council.

• Please consult page 3 for the required clearances to combustible material also ensure the position of structural elements near the proposed flue.

• Because of the positive pressure in the flue, sealing of all 75mm stainless joints is mandatory – use high temperature sealant. Both inner and outer flue joints must be riveted.

• Seismic Restraint: Please see page 9 for requirements.

• Warranty: To validate warranty following installation a copy of the completed Warranty Registration Form/Producer’s Statement must be forwarded to: Switch - Fax (03) 341 8057.

Page 5: Enviro EF2 Classic Wood Pellet Fire FPI CB and FS CB · 2 Stainless steel inner liner ø75mm x 900mm long 5 8 Rain cap 75mm 1 12 T-adaptor/cleanout – ø75mm 1 16 Clamp – ˜exible

5

November 2011

Internal Standard Flue Kit (50)Internal Standard Flue Kit

Each 50 Internal Standard Flue Kit contains:-

ytitnauQnoitpircseDoN traP

1 Galvanised outer linerø100mm x 900mm long 1

4

3

2

1

1

1

1

1

1

2

2 Stainless steel inner linerø75mm x 900mm long

4a Black p/coat outer linerø100mm x 900mm long

5 Inner/outer �ue liner spacer

6c Ceiling thimble ø107mm hole

7c Ceiling decor plateø107mm hole – white

8 Rain cap 75mm

9 Rain Cap 100mm

10b Elbow 45° – ø75mm stainless– black (painted)

12H T-adaptor/cleanout – ø75mm– black (painted)

23 Support angle 950mm long– 50mm x 50mm sides

This �ue kit may be used in new and replacementapplications in rooms with stud height of 2.4m. Theoverall height of the �ue is 3.6m. The visible �u e is�nished in black and the ceiling plate is white. T hesupport angles for securing the liner to the ceilin g arenot shown. Kit is supplied in a carton.

Heat-resistant�oor protector

Seismic restraint(to be �tted)

50mm minimum clearance if lined �ue

600mm fromroof

penetration

~210 mm

150mm (minimum)

Note: The Davin 50 Internal Standard FlueKit complies with AS/NZS 2918:2001 as perApplied Research Test Report 05/1185, dated15 September 2005. All �res must be installed by a quali�edinstaller as per the manufacturer’sinstructions and AS/NZS2918:2001.

50

To order : Telephone 0800 765 431. Fax 64 3 341 8057 [email protected] www.switchenergy.co.nzDecember 2006

Drawing representative only - not to scale.

This flue kit may be used in new and replacement applications in rooms with stud height of 2.4m. The overall height of the flue is 3.6m. The visible flue is finished in black and the ceiling plate is white. The support angles for securing the liner to the ceiling are not shown. Kit is supplied in carton.

Page 6: Enviro EF2 Classic Wood Pellet Fire FPI CB and FS CB · 2 Stainless steel inner liner ø75mm x 900mm long 5 8 Rain cap 75mm 1 12 T-adaptor/cleanout – ø75mm 1 16 Clamp – ˜exible

6

November 2011

External Standard Flue Kit (51)

Each 51 External Standard Flue Kit contains:-

ytitnauQnoitpircseDoN traP

1 Galvanised outer linerø100mm x 900mm long

2 Stainless steel inner linerø75mm x 900mm long

5 Inner/outer �ue liner spacer

6w Wall thimble – 2 piecesø102mm holes

6s So�t thimble ø107mm hole

7w Wall decor plateø102mm hole – white

8 Rain cap 75mm

9 Rain Cap 100mm

26 Lined T-adaptor

This �ue kit may be used in new and replacementapplications with the �ue penetrating the wall behindthe �re, running vertically up an outside wall andpenetrating the so�t. The overall height of the f lue is3.6m. All visible �ue has a galvanised �nish, and can bepowdercoated on request. Kit is supplied in a carton.

Note: The Davin 51 External Standard FlueKit complies with AS/NZS 2918:2001 as perApplied Research Test Report 05/1185, dated15 September 2005. All �res must be installed by a quali�edinstaller as per the manufacturer’sinstructions and AS/NZS2918:2001.

Heat-resistant�oor protector

Seismic restraint(to be �tted)

600mm fromroof penetration

100mm (minimum)

150mm (minimum)

External Standard Flue Kit51

4

4

2

1

1

1

1

1

1

To order :December 2006 Telephone 0800 765 431. Fax 64 3 341 8057 [email protected] www.switchenergy.co.nz

Drawing representative only - not to scale.

This flue kit may be used in new and replacement applications with the flue penetrating the wall behind the fire, running vertically up an outside wall and penetrating the soffit. The overall height of the flue is 3.6m. All visible flue has a galvanised finish, and can be powdercoated on request. Kit is supplied in a carton.

Page 7: Enviro EF2 Classic Wood Pellet Fire FPI CB and FS CB · 2 Stainless steel inner liner ø75mm x 900mm long 5 8 Rain cap 75mm 1 12 T-adaptor/cleanout – ø75mm 1 16 Clamp – ˜exible

7

November 2011

Insert Flue Kit (52)

Each 52 Insert Flue Kit contains:-

ytitnauQnoitpircseDoN traP

2 Stainless steel inner linerø75mm x 900mm long 5

8 Rain cap 75mm 1

12 T-adaptor/cleanout – ø75mm 1

16 Clamp – �exible �ue tostainless �ue pipe 1

19 Flexible �ue pipe – stainlesssteel ø75mm x 1m 1

21 Bracket 75mm securing�ue pipe to wall 1

839 Casing cover – standard ø75mm - ø300mm 1

34 Chimney cover – may be requiredas an optional extra

This �ue kit may be used in replacement applicationsin masonry chimneys. The overall height of the �ue is4.5m. Kit is supplied in two cartons.

Note: The Davin 52 Insert Flue Kitcomplies with AS/NZS 2918:2001 as perApplied Research Test Report 05/1185,dated 15 September 2005. All �res must be installed by a quali�edinstaller as per the manufacturer’sinstructions and AS/NZS2918:2001.

Heat-resistant�oor protector

Seismic restraint chain. To be �tted one on eachside of the �re at the mid point. The chain should

have a breaking strength of at least 350kg orminimum 3.5mm nominal diameter. Chains

should be anchored to the �oor (not framing ormasonry), and should be as short as possible,

only allowing access to unbolt the chains from the�re to allow the �re to be pulled forward for servicing.

Chimney cover– optional extra

150mm(minimum)

Insert Flue Kit52

To order :December 2006 Telephone 0800 765 431. Fax 64 3 341 8057 [email protected] www.switchenergy.co.nz

Drawing representative only - not to scale.

Page 8: Enviro EF2 Classic Wood Pellet Fire FPI CB and FS CB · 2 Stainless steel inner liner ø75mm x 900mm long 5 8 Rain cap 75mm 1 12 T-adaptor/cleanout – ø75mm 1 16 Clamp – ˜exible

8

November 2011

Built In Heater (non-chimney) Flue Kit (54)

Each 54 Built-in-Heater Flue Kit (non-Chimney installation) contains:-

ytitnauQnoitpircseDoN traP

Galvanised outer linerø100mm x 900mm long

Stainless steel inner linerø75mm x 900mm long

Inner/outer �ue liner spacer

Ceiling thimble ø107mm hole

Rain cap 75mm

Rain cap 100mm

Elbow 45° – ø75mm stainless– black (painted)

T-adaptor/cleanout – ø75mm

This �ue kit may be used in new or existing timberchimneys. The overall height of the �ue is 3.6m.Kit is supplied in a carton.

Note: The Davin 54 Built-in-Heater Flue Kit(non-Chimney) complies with AS/NZS2918:2001 as per Applied Research TestReport 05/1185, dated 15 September 2005. All �res must be installed by a quali�edinstaller as per the manufacturer’sinstructions and AS/NZS2918:2001.

600mm fromroof

penetration

Built-in-Heater Flue Kit(non-Chimney installation)

54

To order :December 2006

4

4

2

1

1

1

1

1

1

2

5

6c

8

9

10b

12

50mm minimum clearance if lined �ue

150mm (minimum)

Heat-resistant�oor protector

Seismic restraint(to be �tted)

Telephone 0800 765 431. Fax 64 3 341 8057 [email protected] www.switchenergy.co.nz

Drawing representative only - not to scale.

Page 9: Enviro EF2 Classic Wood Pellet Fire FPI CB and FS CB · 2 Stainless steel inner liner ø75mm x 900mm long 5 8 Rain cap 75mm 1 12 T-adaptor/cleanout – ø75mm 1 16 Clamp – ˜exible

9

November 2011

Flashing Options:

Decktite - For all Steel Roof Profiles

Please circle the flashing option to be used. When considering an alternative method please consult your local council.

Seismic Restraint

Concrete Floor

Installation scenarios for the Classic FS and Built In Models require the use of hold-down anchors (one on each side)

Fixing to Concrete Floor:

Minimum M8 expansion anchors (M10 recommended) or min M8 epoxy- set anchors. Approved Anchors: Expansion Anchors-Ramset Dynabolt and Trubolt, Hilti HAS.Epoxy-set Anchors – Ramset Epcon, Ramset Chemset and Hilti HVU.

Installation of the Insert Model (non-combusitble cavity) requires the use of a seismic restraint chains to be fitted one on each of the fire at the mid-point. The chain should have a breaking strength of at least 350kg or minimum 3.5mm nominal diameter. Chains should be anchored to the floor (not framing or masonry), and should be as short as possible, only allowing access to unbolt the chains from the fire to allow the fire to be pulled forward for servicing.

Timber Floor

Minimum 14g x 60mm screws (6.3mm diameter) or M10 X 90mm coach-screws. These shall be fixed a minimum of 40mm into the centre-line of the existing floor joists. If screws cannot be installed directly into an existing floor joist, solid blocking between joists (min size 90x45) shall be provided.