esmeralda i e a4
TRANSCRIPT
7/27/2019 Esmeralda i e a4
http://slidepdf.com/reader/full/esmeralda-i-e-a4 1/6
Assembly Instructions
Mountain fold(dotted line)Make a mountain fold.
Valley fold(dashed and dotted line)
Make a valley fold.Scissors line(solid line)Cut along the line.
Cut in line(solid line)Cut along the line.
Glue spot(Red dot)
Glue parts with the same number together.
Glue spot(Green dot)Glue within the same part.
Glue spot(Blue dot)Glue to the rear of the other part.
Glue
The glue spot(colored dot)shows where to apply the glue.
Tools and materials
Assembly tip
Caution
Scissors, set square, glue(We recommend stick glue), pencil, usedballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valleyfold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young childrenso be sure to keep them out of the reach of young children.
View of completed model
Assembly Instructions : Six A4 sheets (No. 1 to No. 6)
*Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold.
* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.
* This model was designed for Papercraft and may differ from the original in some respects.
Before starting assembly: Writing the number of each section on its back side before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after cutting out the sections.) The parts used will vary somewhat, depending on whether the completed vessel will be modeled to depicta ship facing wind from the left (with the bow pointed to the right) or from the right (with the bow pointed tothe left). First decide where you want to display the completed vessel, then decide whether the bow shouldpoint to the left or right.
Bow pointed to the right (A - standard parts)
Bow pointed to the left (B - optional parts)
Indicates sections that should be glued first,then cut out.
Indicates sections that should be folded once,then unfolded.
After folding the part once and gluing the twofolds together, cut out from the yellow area.
Glue parts 2 and 3 together inthe same way.
Indicates where sections shouldbe glued together.
Indicates where to insert sections.Do not glue the sections together.
© Canon Inc. © M. Nishiguchi/SENAUNShips of the world : Esmeralda : Assembly Instructions
http://www.canon.com/c-park/
7/27/2019 Esmeralda i e a4
http://slidepdf.com/reader/full/esmeralda-i-e-a4 2/6
© Canon Inc. © M. Nishiguchi/SENAUNShips of the world : Esmeralda : Assembly Instructions
(bow pointed to the right) or(bow pointed to the left; optional part)
After folding this part, unfold and cut outfrom the cream-colored area.
Apply glue to part 26 at thespot shown in the illustration,and then attach it to the mast.
Glue the glue spots of parts 11, 19,and 26 to the bottom side of the deck.
Curl part 44 by wrapping it
around a thin stick(such as a toothpick).
Insert untilthe corners meet.
Glue the rear sides of
these parts together.
7/27/2019 Esmeralda i e a4
http://slidepdf.com/reader/full/esmeralda-i-e-a4 3/6
© Canon Inc. © M. Nishiguchi/SENAUNShips of the world : Esmeralda : Assembly Instructions
Glue these partstogether.
Cut away the yellow area. Cut awaythis area for part 29 in the same way.
Glue the glue spots of part 29
in place as shown by the arrows.
Glue the rear sides of these parts together.
7/27/2019 Esmeralda i e a4
http://slidepdf.com/reader/full/esmeralda-i-e-a4 4/6
© Canon Inc. © M. Nishiguchi/SENAUNShips of the world : Esmeralda : Assembly Instructions
Glue part 36 in place after firstattaching part 35 to the hull.
7/27/2019 Esmeralda i e a4
http://slidepdf.com/reader/full/esmeralda-i-e-a4 5/6
© Canon Inc. © M. Nishiguchi/SENAUNShips of the world : Esmeralda : Assembly Instructions
As shown in the illustration,use A parts (standard parts) forparts 45 - 48 when the bow will faceto the right and B parts (optional parts)when the bow will face to the left.
For parts 66 - 69, choose A parts(standard parts) or B parts (optional parts)
depending on the direction in whichthe bow will point.
Surface A on top(bow pointed to the right)
Surface B on top(bow pointed to the left)
Attach parts 53 - 56 (the yards) to the vessel masts. If the bow willpoint to the right, attach the yards so that surface A is on top. Ifthe bow will face to the left, attach so that surface B is on top.
Glue the yards in place at an angle, as shown in the illustration,so that the model will resemble a ship sailing in the wind.
Fold once and glue the folds together,then give the sails a bulging appearance.If you plan to have the bow face to the right,curl the sails so that surface A will bulge out.If the bow will face to the left, curl the sailsso that surface B will bulge out.
7/27/2019 Esmeralda i e a4
http://slidepdf.com/reader/full/esmeralda-i-e-a4 6/6
© Canon Inc. © M. Nishiguchi/SENAUNShips of the world : Esmeralda : Assembly Instructions
C hile a n v e sse lE smer a ld a
C hile a n v e sse lE smer a ld a
C h i l e a n v e s s e l
E s m e r a l d a
Fold parts 72 - 75 (the square sails) in half and glue both folds together.After curling these from top to bottom as shown in the illustration, make them curlfrom the center to the outside, to make it appear as if they are catching the wind.
Glue the rear sides ofthese parts together.
Finished!