estates/mdi/mdp hostel /2017 02 march 2017 sub: renovation of … for renovation of mdp... · (j)...

Estates/MDI/MDP hostel /2017 02 March 2017

Sub: Renovation of MDP Hostel rooms at MDI Campus, Gurugram Dear Sir, 1. Sealed tenders are invited for Renovation of existing MDI Hostel rooms in Parthenon &

Nalanda at MDI Campus, Gurugram. Please submit your Technical & Commercial bids in a two separate envelopes. The envelop should be clearly marked as Commercial/ Technical Bid. The tenders should be submitted in a sealed cover addressed to:

The Registrar & Secretary

Management Development Institute Mehrauli Road, GURUGRAM - 122001

2. The tenders should reach on or before 1500 hours, 27th March 2017. The rates of items

being quoted will include the cost of material, wastage, labour etc. However, the details of taxes to be paid should be mentioned separately. Thus the cost of item being quoted in the BOQ will be exclusive of taxes.

3. A total 110 MDP Hostel rooms with 110 Toilets are proposed to be renovated (30 rooms in Nalanda and 80 rooms in Parthenon building). As the hostel is occupied, only 10-15 hostel rooms shall be handed over the renovation at a stretch and possession of other rooms shall be given after handing over earlier rooms. This may please be noted while quoting the rates.

4. The schedules of quantities for Nalanda Hostel are enclosed at Annexure A and for the Parthenon Hostel are enclosed as Annexure B. The plumbing and electrical schedules for the both hostels are given in A-II, A-III, and B-II, B-III respectively. The schedule of makes is enclosed as Annexure C. The terms and conditions are given below:-

5. Terms and Conditions:-

(a) Running advance payments against the work done not exceeding 80% of the value of work done shall be paid on submission of bills by the Contractor.

(b) Retention amount of 5 % will be retained till the satisfactory completion of work and will be released after 3 month of hand over of the completed work.

(c) An earnest money deposit of Rs.2,00,000/- (Rs. Two Lakhs only) shall also be submitted along with the tender by way of Demand Draft/ Pay order favoring Management Development Institute payable either at Gurgaon. While awarding the work, the earnest money deposited shall be treated as security deposit and will be released after one month of satisfactory completion of job. The earnest money deposit of unsuccessful tenders will be refunded.

(d) TDS and WCT shall be deducted as per rules. (e) The entire work should be completed within 180 days from the date of awarding the

work. Damage for delay in completion of the work would be Rs.2,000/- (Rs. Two thousand only) per day subject to a maximum of Rs.1,00,000/- (Rs. One Lakh only). Decision of the Institute in this regard would be final.

(f) The rates of extra works, if executed, shall be based on CPWD schedule of rates and for items not covered therein shall be worked out as per prevailing market rates added with 15% contractor’s profit and overheads for which a rate analysis shall have to be submitted by the Contractor which would be subject to approval of the Institute.

(g) The work shall be executed as per CPWD specification. The mode of measurements of work done shall also be based on CPWD specification.

(h) First quality paint manufactured by the following firms (in the same order of preference) shall be used and only be brought to the site in sealed containers. Contractor should also ensure that only the required quantities of materials should be brought to the Campus.

(i) Paint & Primer - Nerolac /Johnson & Nicholson/British Paint/ Asian Paints/Berger (ii) Snow cem - Super snowcen / Indocem/ Acrocem (iii) Distempering - Berger / Shalimar / Asian

(i) The Quantity to be executed may vary according to actual requirement. The payment

shall be made on the basis of actual measurement of work done at the rates quoted by the Contractor as per schedule of quantities enclosed.

(j) The splashes of white wash, painting and distemper shall be cleaned by the Contractor at his own cost and no extra payment will be admissible for the same.

(k) The Institute reserves the right to get the whole or part of work done through one or more parties.

(l) Water and electricity shall be supplied by the Institute free of cost. (m) Contractor shall bring only the actual quantity of materials required after measuring the

actual area of work to be done at site. (n) The dismantled mulba/rubbish should be disposed off outside the campus at a suitable

dumping ground at no extra cost within 7 days of completion of work or it would be got done by the Institute at the risk and cost of the contractor and the said amount shall be deducted from the bills of the Contractor.

(o) The work should be organized without causing inconvenience/disturbance to the participants staying in the hostel. No claim on account of non-availability of rooms shall be entertained and the work shall be carried out as per the rooms made available to the Contractor from time to time. Whitewashing / distempering etc. shall be taken up by putting polythene or other covers to protect the furniture from any splashes / damages. The floors would be thoroughly cleaned and splashes / spots shall be washed and removed.

(p) Contractor should make own arrangement for all tools and plants required to complete the job.

(q) The watch and ward of materials brought at site shall be the responsibility of the contractor.

(r) The work should be organized/carried out without affecting the normal functioning of the Institute. There should be least disturbance for the movement of traffic inside the Campus.

(s) The contractor must get acquainted with the proposed site for the work and study specifications and conditions before quoting the rates.

(t) No payment will be made to the contractor for damage caused by rains or other natural calamities during the execution of the work and no claim on this account will be entertained. The damages, if any , occurred shall be rectified without any extra cost.

(u) At least one authorized representative should always be available at site of work to take instructions from Engineer-in-Charge/Officer and ensure proper execution of work. No work will be done in the absence of such an authorized representative.

(v) The contractor shall get the samples of materials approved sufficiently in advance from the Institute. The materials brought at site shall strictly conform to the quality of samples approved and in case of variation such materials shall liable to be rejected and to be removed from the site within 24 hours of the rejection by the Engineer-in-Charge/Officer. The Sample of electrical fittings shall be got approved before bulk procurement by the Contractor.

(w) The Contractor, if need so arises, shall remove one or more labour /supervisor from the premises of the Institute at the direction of the Institute.

(x) The contractor should also comply with the existing Labour Laws/License, Provident Fund Rules and other statutory rules prevailing/applicable in Haryana State.

(y) The contractor shall take all safety precautions for the safety of his employees and the Institute shall not be in any way liable for any damage/liability on account of any mishap or negligence of the Contractor.

(z) Vitrified, Ceramic tiles manufactured by one of the agency like M/s, Kajaria, Somany Orient, Bell Ceramic shall only be used. The sample of the tiles shall be got approved before commencement of work. Good quality of adhesive shall be used for fixing the tiles. Nothing extra shall be payable for removing the furniture from the rooms for fixing Ceramic tiles and placing it back after completion of work.

6. The prescribed list of approved make is attached at Annexure C. 7. MDI reserves the right to accept or reject any of all the tenders without assigning any reason

what so over. Sd xxxxx (Subhash Chand)

Resident Engineer Encl: Annexures: A-I, A-II,A-III, B-I,B-II,B-III & C

Annexure A-I

S.NO. DESCRIPTION UNIT QTY RATE AMOUNT

Civil Work

1 Providing and injecting chemical emulsion for wooden Cab board anti termite treatment and

creating a chemical barrier complete as per IS 6313 (part II 1971) with 5 year guarantee M2 35

2 Scraping of existing paint with hacking of existing plaster and making the surface for POP punningM

2 60

3 Dismantling and refixing of new false ceiling in toilet and disposal of wastage outside MDI Campus.M

2 15

4 POP Punning (10mm-12mm): Providing and applying average 10 - 12 mm thk Plaster of Paris of

fine quality to the walls and columns in square plumb line and level the surfaces.M

2 1480

5 Providing and applying white cement Birla putty 1mm-2mm over the plastered wall surface to

prepare the surface even and smoothe.M

2 100

6 Providing & applying of 6-10 mm thick plaster in 1:4 morter ratio M2 50

7 Gypsum board Ceiling : P/F at all height false ceiling of 12.5 mm thick board / gypsum board

including frame work made of special sections power pressed from M.S. sheet and

galvanised in accordance with zinc coating consisting of angle cleats of size 25 mm wide x 1.6

mm thick with flanges of 22 mm and 37 mm at 1200 mm c/c to centre one flange fixed to the

ceiling with dash fastner 12.5 mm dia x 40 mm long with 6 mm dia. bolts to the angle hangers of

25 x 25 x 0.55 mm of required length, and other end of angle hanger being fixed with nut and

bolts to G.I. channels 45 mm x 15 mm x 0.9 mm running at the rate of 1200 mm centre to centre

to which the ceiling section 0.5 mm thick botton wedge of 80 mm with tapered flanges of 26

mm each having clips of 10.5 mm at 450 mm centre to centre shall be fixed in a direction

perpendicular to G.I channel with connecting clips made out of 2.64 mm dia. x 230 mm long

G.I.wire at every junction including fixing the gypsum board with ceiling section and perimeter

channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter

of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre with 25

mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of

tapered and square edges of the Lagyp board with standard Lagyp easy joint compound (3

layer) , paper tapes, finisher amd two coats of primer suitable for gypsum board as per

manufactures specification and also including the coat of making opening for light fittings,

grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete.

M2 30

8 Providing and applying 2 or more coats of paint of on walls or ceiling wherever advised . by sand

papering and applying putty to achieve smooth and truly levelled surface priemer coat applied

before the application of finishing coat as recommended by manufactures specification

i) Plastic Emulsion Paint M2 1550

ii) Satin finish Enamel paint for door, window frame & shitters etc M2 150

iii) Synthetic Enamel paint on above M2 RO

9 Removing existing enamel paint door frame and applying new polish with lacure finish as per

approved shade.Nos. 20

10 Providing and fixing of 35mm thick flush door shutter size 7'-0" x 3'-3" with both side laminate

including accessories like lock, handle, tower bolts, door stopper etc with door closers and polish

/paint where ever required complete.

Nos. 5

11 3mm thick teak wood ply veneering on both sides of flush door including hinges and teak wood

leaping on all sides with leaguer polishing on both sides complete in all respect.M

2 80

12 Providing and fixing of beading inside/outside of entrance door frame beading of size (2" x 1")

including polishing / painting as per direction of engineer in-charge.Rmtr 310

13 Providing and fixing of 100mm high front cove pelmet for covering in gypsum board with GI frame

as per direction of engineer in-charge.Rmtr RO

14 Providing and fixing of POP cornice on room ceiling of size 3" x3" corner of walls as approved

pattern finished smooth all as per direction of engineer in-charge.Rmtr 510

15 Providing & Fixing aluminum curtain drapery rod 25mm dia for window with brackets and ilet

rings.Rmtr 180

16 Provding and Fixing of cloth cartain in window as per approved colour and design. The basic cost

of cloth is Rs. 300/mtr. The width of Curtain cloth will be 54" and finish length as actual will be

payble. The folded length at the botom of the curtain will be atleast 3" minimum.Rmtr 200

17 Providing and fixing 20mm thick granite stone of approved quality on counter tops of toilet in

cement mortar 1:4 (1 cement: 4 coarse sand) and jointed with 'white cement slurry mixed with

pigment to match the colour of the stone including cutting of hole as required, making moulding

as per design and edge polishing etc. complete. (Basic cost of granite stone Rs.150/-per sft.).

M2 35

Management Development Institute

Post Box No.- 60, Mehruli Shukrali Road

Gurgaon

Sub:- Rates for Renovation of in Nalanda Building

18 Providing and laying 8mm thick ceramic tiles of approved make and quality Engineer inchargeof

450 X 300 mm sizes in dado or as required with 12mm cement mortar 1:3 ( 1 cement : 3 fine sand)

jointed with white cement , mixed with pigment to match the colour of the tiles as per design and

pattern in the Architects drawings complete . (Basic cost of tile Rs.60/-per sft.).

M2 680

19 Providing and laying 10 mm thick tiles (jointless) of approved size ( 600 x 600 approx.), make,

quality on floor, skiriting with 12mm (avg.) thick cement mortar 1:3 mix (1cement: 3 coarse sand)

and jointed with white cement slurry mixed with pigment to match the shade of the tiles complete

or chemical adhesive of approved make including providing the joints with whole cement &

matching pagments as per design with approved quality tiles.

M2 590

20 Dismantelling and demolishing Tiles work at all levels and heights as per direction including

necessary scaffolding etc. cleaning, removing the malba as per direction of the Architects

complete.

M2 650

21 Repair & Modification (including providing necessary lamination, polishing, inside painting etc) of

cupboard shutters with necessary hardware fittings like lock, handle, hinges etc as required.(Size

1.0M X 2.0M X 2 No.s)

M2 20

22 Providing and fixing mortice lock( Godrej make or equivalent) as per design after replacing the

existing lock in the main door Nos 30

23 Providing and fixing twin hook fixed on toilet shutter back side Nos 30

24 Providing & fixing head board bed unit to the wall at the location shown in layout of sized 2500 x

1200 mm size consisting of 18 mm thick Teak veneered with 2nd class Teak wood frame 60 x 60

mm and equal vertical & horizontal panels upholstered with 12mm thick polyurethene foam &

clad with fabric / leatherite as per sample and direction of engineer in-charge.

M2 120

25 Repair & modification of study table in the rooms including providing necessary lamination,

polishing, painting & hardware fittings.Nos 30

26 Repair, modification & Polishing existing furniture like beds, bed side tables looking mirror, book

shelf etc.(One set of Room)Nos 30

27 Removing existing wire mesh of window shutter & providing and fixing SS wire mesh with beading

complete.Sft 30

28 Repairing of existing study chair (Teak wood) and providing good density foam and cusion with

leatherite/ cloth upholstery with maching colour polish as per table, bed etc.Nos 30

29 Electrical / Net working / Telephone points relocation using compatible existing I/O plates CAT 6

(E) D link brand networking cables compatible telephone & electrical cabling running through

grooves provided behind the skirting and routed over the false ceiling and chased on the wall to

the required location, new gang box of ANCHOR ROOM equivalent make accessories located

below the bed side table/wood desk or as per direction of engineer in-charge.

Nos 30

30 Providing & Fixing 6mm thick 1500x1200 mm size float glass mirror of approved brand edges to be

grinded & finished smooth in Toilet using 8 mm FISHERS fastners and self driving magna thread

screws 40 mm x 25 mm dia stainless steel spacers 8mm hold of DELITE or equivalent make as per

the direction of engineer in-charge.

Nos 30

31 Providing & fixing 450 x 100 & 12 mm thick Toughened glass shelf float glass fitted at the side of

wash basin counter using "D" brackets fixed with 6mm Fisher make or equivalent fastners.

Complete.

Nos 30

32 Providing & Fixing corner glass shelves of 200 mm radius 12mm thick Toughened glass fitted in

shower area using "D" brackets fixed with 6mm fastners completedNos 30

33 Providing and fixing stainless steel towel red 600mm long as per sample and direction fo

engineer in-charge.Nos 30

34 Manufacturing & supplying of luggage rack of 850 x 540 x 450mm high with teak veneered top

provided with solid teak wood batons & wooden legs & finished in French Sprit polish complete

with laqur coating as per sample and directions of Engineer-In-ChargeNos RO

35 Providing & Fixing wooden moulded beading of door and window frames with iron screws plugs

and polishing the same matching with the shade and color of the shutter all complete as per

directions of the of Engineer-In-Charge

Rmtr 164

Electrical Items

Unit Quantity Rate

Amount

1 Providing and fixing 6amps Switch Nos 400

2 Providing and fixing 6amps Light Socket Nos 200


4 Providing and fixing 16amps Socket Nos 95

5 Providing and fixing Ceiling Fan Regulater Nos 30

6 Providing and fixing T.V Socket Nos 30

7 Providing and fixing Rj 45 Data Socket Nos 30

8 Wiring for light point with (3x1.5 sq mm ) insulated Stranded copper conducter wire in concealed

M.S Condut in false ceiling as directed including providing 6 amps flush type switches

a First Point Controlled by one no 6amps Switch Nos 60

9 Same as above item no 8 but loop point i.e. wiring of point looped from first point with (2x1.5 sq

mm) insulated copper wire in concealed / Exposed M.S conduteNos 240

10 Removing & Fixing Light Fixtures with assembling,fixing in position testing and commissioning of

all light fixtures

a Tube Light Nos 30

b Mirror Light Nos 30

c Ceiling Light Nos 60

d Wall Bracket Light Nos 30

e Foot Light Nos 30

11 Providing & Fixing Light Fixture

a 1x28 Watts T-5 lamp Tube light wipro or philips make LED Nos 30

b 1x14 watt T-5 lamp for Mirror light wipro or philips make LED Nos 30

c 2x18 watt CFL lamp for Ceiling light fixture wipro or philips make LED Nos 60

d Wall bracket light fixture wipro or philips make 7/5 watt LED Nos 30

e 1x9 watt CFL Foot light fixture wipro or philips make Nos 30

f Item no.8 - 1x28 Watt T-5 lamp cove light Nos 60

g Item No 9 - Loop Point 1x28 Watt T-5 lamp cove Light Nos 240

Description of ItemsS.No.

Annexure A-II


1

Providing & fixing white glazed vitreous china single trap syphonic pattern water closet( floor

mounted, /P trap) having back inlet ,supporting chair with PVC cistern complete with all internal

fittings/accessories (Parryware).Testing & commissioning of sanitary fixtures as per above details,

Make Parryware Hindustan

Each 36.00

2

Providing & fixing white glazed vitreous china wash basin (Flat back) with R.S. or C.I. brackets

painted white, C.P. brass chain with rubber plug 32mm C.P. brass waste of standard pattern, 32

mm dia. C.P. brass bottle trap and union 32 mm dia C.P. pipes to wall flange. complete including

cutting and making good the walls wherever required.

Oval/round under counter wash basin for mounting under the counter Make: Parryware

Hindustan. Testing & commissioning of sanitary fixtures as per above details.

Each 36.00

3

Providing & fixing 15 mm dia C.P. brass angle valves with 450mm long C.P. Copper connecting

pipe union nut C.P. cast brass wall flange. Make: Jaguar. Testing & commissioning of sanitary

fixtures as per above details

each 70.00

4Providing & fixing Hand Shower (Health Faucet) with 8mm dia, 1M long PVC tube and wall hook.

Make: Jaguar. Testing & commissioning of sanitary fixtures as per above detailseach 35.00

B: Internal water supply

1

Providing and fixing Chlorinated polyvinyl Chloride (CPVC) pipes,havings thermal stability for hot &

cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps

at 1.00 m spacing.This includes jointing of pipes & fittings with CPVC solvent cement and the cost

of cutting chases and making good the same including testing of joints complete as per direction

of Engineer in charge,fixing at wall/ceiling level supported by clamps, hangers, structural steel

supports, etc.Cost shall include making connections with G.I. pipes & fittings.

a) 20 mm OD pipe Rmt 372.00

b) 25 mm OD pipe Rmt 177.00

d) 40 mm OD pipe Rmt 10.00

2Providing & fixing brass gun metal lever operated ball valve. Tested to a pressure of 15 Kg /

Sqcm. Including flanges/union, nuts, bolts, washer etc. Complete as required.

b) 20 mm dia each 36.00

c) 25 mm dia each 36.00

3 Providing and Fixing of Center Hole Basin mixer each 30.00

4 Providing and Fixing of Two way Bib Cock each 30.00

5 Providing and Fixing of C.P.Jali each 72.00

6

Providing & fixing 15 mm dia C.P. brass Long Body bib cock with C.P. wall flange of approved

quality. (Jaguar) Testing & commissioning of sanitary fixtures as per above details. each 36.00

7 Providing & Fixing of Urinal with censor Make Jaguar Nos 6.00

8 Providing & Fixing of 25 Litra Geyser (Make Marc/ Hindware/ Venus) Nos 30.0

9 Provinding and Fixing of urinal glass partion Paryware. Nos 3.00

SUB AEAD A: Sanitary Fixtures & Fittings

PLUMBING WORK

Annexure A-III

Annexure B-I


Civil Work

1 Providing and injecting chemical emulsion for wooden Cab board anti termite treatment and creating

a chemical barrier complete as per IS 6313 (part II 1971) with 5 year guaranteeM

2 80

2 Scraping of existing paint with hacking of existing plaster and making the surface for POP punningM

2 120

3 Dismantling and refixing of new false ceiling in toilet and disposal of wastage outside MDI Campus.M

2 60

4 POP Punning (10mm-12mm): Providing and applying average 10 - 12 mm thk Plaster of Paris of fine

quality to the walls and columns in square plumb line and level the surfaces.M

2 4200

5 Providing and applying white cement Birla putty 1mm-2mm over the plastered wall surface to

prepare the surface even and smoothe.M

2 150

6 Providing & applying of 6-10 mm thick plaster in 1:4 morter ratio M2 50

7 Gypsum board Ceiling : P/F at all height false ceiling of 12.5 mm thick board / gypsum board

including frame work made of special sections power pressed from M.S. sheet and galvanised

in accordance with zinc coating consisting of angle cleats of size 25 mm wide x 1.6 mm thick with

flanges of 22 mm and 37 mm at 1200 mm c/c to centre one flange fixed to the ceiling with dash

fastner 12.5 mm dia x 40 mm long with 6 mm dia. bolts to the angle hangers of 25 x 25 x 0.55 mm

of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45

mm x 15 mm x 0.9 mm running at the rate of 1200 mm centre to centre to which the ceiling section

0.5 mm thick botton wedge of 80 mm with tapered flanges of 26 mm each having clips of 10.5

mm at 450 mm centre to centre shall be fixed in a direction perpendicular to G.I channel with

connecting clips made out of 2.64 mm dia. x 230 mm long G.I.wire at every junction including fixing

the gypsum board with ceiling section and perimeter channels 0.5 mm thick 27 mm high having

flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of

rawl plugs at 450 mm centre to centre with 25 mm long drive-all screws @ 230mm interval including

jointing and fixing to a flush finish of tapered and square edges of the Lagyp board with standard

Lagyp easy joint compound (3 layer) , paper tapes, finisher amd two coats of primer suitable for

gypsum board as per manufactures specification and also including the coat of making opening for

light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all

complete.

M2 60

8 Providing and applying 2 or more coats of paint of on walls or ceiling wherever advised . by sand

papering and applying putty to achieve smooth and truly levelled surface priemer coat applied before

the application of finishing coat as recommended by manufactures specification

80

I) Plastic Emulsion Paint M2 4300

ii) Satin finish Enamel paint for door, window frame & shitters etc M2 700

iii) Synthetic Enamel paint on above M2 RO

9 Removing existing enamel paint door frame and applying new polish with lacure finish as per

approved shade.Nos. 60

10 Providing and fixing of 35mm thick flush door shutter size 7'-0" x 3'-3" with both side laminate

including accessories like lock, handle, tower bolts, door stopper etc with door closers and polish

/paint where ever required complete.

Nos. 15

11 3mm thick teak wood ply veneering on both sides of flush door including hinges and teak wood

leaping on all sides with leaguer polishing on both sides complete in all respect.M

2 180

12 Providing and fixing of beading inside/outside of entrance door frame beading of size (2" x 1")

including polishing / painting as per direction of engineer in-charge.Rmtr 850

13 Providing and fixing of 100mm high front cove pelmet for covering in gypsum board with GI frame as

per direction of engineer in-charge.Rmtr 10

14 Providing and fixing of POP cornice on room ceiling of size 3" x3" corner of walls as approved pattern

finished smooth all as per direction of engineer in-charge.Rmtr 1310

15 Providing & Fixing aluminum curtain drapery rod 25mm dia for window with brackets and ilet rings.Rmtr 450

16 Provding and Fixing of cloth cartain in window as per approved colour and design. The basic cost of

cloth is Rs. 300/mtr. The width of Curtain cloth will be 54" and finish length as actual will be payble.

The folded length at the bottom of the curtain will be atleast 3" minimum.

Rmtr 350

Management Development Institute

Post Box No.- 60, Mehruli Shukrali Road

Gurgaon

Sub:- Rates for Renovation of in Parthonen Building


17 Providing and fixing 20mm thick granite stone of approved quality on counter tops of toilet in cement

mortar 1:4 (1 cement: 4 coarse sand) and jointed with 'white cement slurry mixed with pigment to

match the colour of the stone including cutting of hole as required, making moulding as per design and

edge polishing etc. complete. (Basic cost of granite stone Rs.150/-per sft.).

M2 90

18 Providing and laying 8mm thick ceramic tiles of approved make and quality Engineer inchargeof 450 X

300 mm sizes in dado or as required with 12mm cement mortar 1:3 ( 1 cement : 3 fine sand) jointed

with white cement , mixed with pigment to match the colour of the tiles as per design and pattern in

the Architects drawings complete . (Basic cost of tile Rs.60/-per sft.).

M2 1650

19 Providing and laying 10 mm thick tiles (jointless) of approved size ( 600 x 600 approx.), make, quality

on floor, skiriting with 12mm (avg.) thick cement mortar 1:3 mix (1cement: 3 coarse sand) and jointed

with white cement slurry mixed with pigment to match the shade of the tiles complete or chemical

adhesive of approved make including providing the joints with whole cement & matching pagments as

per design with approved quality tiles.

M2 1480

20 Dismantelling and demolishing Tiles work at all levels and heights as per direction including necessary

scaffolding etc. cleaning, removing the malba as per direction of the Architects complete. M2 1550

21 Repair & Modification (including providing necessary lamination, polishing, inside painting etc) of

cupboard shutters with necessary hardware fittings like lock, handle, hinges etc as required. (Size 2.80

X 1.00 M2)

M2 50

22 Providing Fixing twin mortice lock (Godrej make or equivalent) as per design after replacing the

existing lock in the main doorNos 80

23 Providing and fixing twin hook fixed on toilet shutter back side Nos 80

24 Providing & fixing head board bed unit to the wall at the location shown in layout of sized 2500 x 1200

mm size consisting of 18 mm thick Teak veneered with 2nd class Teak wood frame 60 x 60 mm and

equal vertical & horizontal panels upholstered with 12mm thick polyurethene foam & clad with fabric

/ leatherite as per sample and direction of engineer in-charge.

M2 350

25 Repair & modification of study table in the rooms including providing necessary lamination, polishing,

painting & hardware fittings.Nos 80

26 Repair, modification & Polishing existing furniture like beds, bed side tables looking mirror, book shelf

etc.(One set of Room)Nos 80

27 Removing existing wire mesh of window shutter & providing and fixing SS wire mesh with beading

complete.Sft 80

28 Repairing of existing study chair (Teak wood) and providing good density foam and cusion with

leatherite/ cloth upholstery with maching colour polish as per table, bed etc.Nos 80

29 Electrical / Net working / Telephone points relocation using compatible existing I/O plates CAT 6 (E) D

link brand networking cables compatible telephone & electrical cabling running through grooves

provided behind the skirting and routed over the false ceiling and chased on the wall to the required

location, new gang box of ANCHOR ROOM equivalent make accessories located below the bed side

table/wood desk or as per direction of engineer in-charge.

Nos 80

30 Providing & Fixing 6mm thick 1500x1200 mm size float glass mirror of approved brand edges to be

grinded & finished smooth in Toilet using 8 mm FISHERS fastners and self driving magna thread

screws 40 mm x 25 mm dia stainless steel spacers 8mm hold of DELITE or equivalent make as per the

direction of engineer in-charge.

Nos 80

31 Providing & fixing 450 x 100 & 12 mm thick Toughened glass shelf float glass fitted at the side of wash

basin counter using "D" brackets fixed with 6mm Fisher make or equivalent fastners. Complete. Nos 80

32 Providing & Fixing corner glass shelves of 200 mm radius 12mm thick Toughened glass fitted in shower

area using "D" brackets fixed with 6mm fastners completedNos 80

33 Providing and fixing stainless steel towel red 600mm long as per sample and direction fo engineer in-

charge.Nos 80

34 Manufacturing & supplying of luggage rack of 850 x 540 x 450mm high with teak veneered top

provided with solid teak wood batons & wooden legs & finished in French Sprit polish complete with

laqur coating as per sample and directions of Engineer-In-Charge

Nos 10

35 Providing & Fixing wooden moulded beading of door and window frames with iron screws plugs and

polishing the same matching with the shade and color of the shutter all complete as per directions of

the of Engineer-In-Charge

Rmtr

450

S.No. Description of Items Unit Quantity Rate Amount


2 Providing and fixing 6amps Light Socket Nos 300


4 Providing and fixing 16amps Socket Nos 260

5 Providing and fixing Ceiling Fan Regulater Nos 80

6 Providing and fixing T.V Socket Nos 80

7 Providing and fixing Rj 45 Data Socket Nos 80

8 Providing and fixing RG 11 For Voice Socket Nos 80

9 Providing and fixing 20amps AC & Gyser Socket & MCB Nos 160

10 Wiring for light point with (3x1.5 sq mm ) insulated Stranded copper conducter wire in concealed M.S

Condut in false ceiling as directed including providing 6 amps flush type switches

a First Point Controlled by one no 6amps Switch Nos 160

11 Same as above item no 10 but loop point i.e. wiring of point looped from first point with (2x1.5 sq

mm) insulated copper wire in concealed / Exposed M.S conduteNos 640

12 Removing & Fixing Light Fixtures with assembling,fixing in position testing and commissioning of all

light fixtures

a Tube Light Nos 80

b Mirror Light Nos 80

c Ceiling Light Nos 80

d Wall Bracket Light Nos 240

e Foot Light Nos 80

f Hanging Light Nos 80

g Exhaust Fan Nos 80

13 Providing & Fixing Light Fixture

a 1x28 Watts T-5 lamp Tube light wipro or philips make LED Nos 80

b 1x14 watt T-5 lamp for Mirror light wipro or philips make LED Nos 80

c 2x18 watt CFL lamp for Ceiling light fixture wipro or philips make LED Nos 80

d Wall bracket light fixture wipro or philips make LED Nos 240

e 1x9 watt CFL Foot light fixture wipro or philips make Nos 80

f Item no.10 - 1x28 Watt T-5 lamp cove light Nos 160

g Item No 11 - Loop Point 1x28 Watt T-5 lamp cove Light Nos 640

h Exhaust Fan(250mm dia) Havells or Newtek Make Nos 80

Annexure B-II

Electrical Items


1

Providing & fixing white glazed vitreous china single trap syphonic pattern water closet( floor

mounted, /P trap) having back inlet ,supporting chair with PVC cistern complete with all internal

fittings/accessories (Parryware).Testing & commissioning of sanitary fixtures as per above details,

Make Parryware Hindustan

Each 80.00

2

Providing & fixing white glazed vitreous china wash basin (Flat back) with R.S. or C.I. brackets painted

white, C.P. brass chain with rubber plug 32mm C.P. brass waste of standard pattern, 32 mm dia. C.P.

brass bottle trap and union 32 mm dia C.P. pipes to wall flange. complete including cutting and making

good the walls wherever required.

Oval/round under counter wash basin for mounting under the counter Make: Parryware Hindustan.

Testing & commissioning of sanitary fixtures as per above details.

Each 80.00

3

Providing & fixing 15 mm dia C.P. brass angle valves with 450mm long C.P. Copper connecting pipe

union nut C.P. cast brass wall flange. Make: Jaguar. Testing & commissioning of sanitary fixtures as

per above details

each 110.00

4Providing & fixing Hand Shower (Health Faucet) with 8mm dia, 1M long PVC tube and wall hook.

Make: Jaguar. Testing & commissioning of sanitary fixtures as per above detailseach 80.00

S.No. Description of Items Unit Quantity Rate Amount

1

Providing and fixing Chlorinated polyvinyl Chloride (CPVC) pipes,havings thermal stability for hot &

cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at

1.00 m spacing.This includes jointing of pipes & fittings with CPVC solvent cement and the cost of

cutting chases and making good the same including testing of joints complete as per direction of

Engineer in charge,fixing at wall/ceiling level supported by clamps, hangers, structural steel supports,

etc.Cost shall include making connections with G.I. pipes & fittings.

a) 20 mm OD pipe Rmt 992.00

b) 25 mm OD pipe Rmt 492.00

d) 40 mm OD pipe Rmt 30.00

4Providing & fixing brass gun metal lever operated ball valve. Tested to a pressure of 15 Kg / Sqcm.

Including flanges/union, nuts, bolts, washer etc. Complete as required.

b) 20 mm dia each 85.00

c) 25 mm dia each 85.00

5 Providing and Fixing of Center Hole Basin mixer each 85.00

6 Providing and Fixing of Two way Bib Cock each 85.00

7 Providing and Fixing of C.P.Jali each 180.00

8Providing & fixing 15 mm dia C.P. brass Long Body bib cock with C.P. wall flange of approved quality.

(Jaguar) Testing & commissioning of sanitary fixtures as per above details.each 85.00

9 Providing & Fixing of Urinal with censor Make Jaguar Nos 6.00

10 Providing & Fixing of 25 Litra Geyser (Make Marc/ Hindware/ Venus) Nos 80.0

11 Provinding and Fixing of urinal glass partion Paryware. Nos 3.00

SUB AEAD B: Internal water supply

SUB AEAD A: Sanitary Fixtures & Fittings

Annexure B-III

PLUMBING WORK

Annexure C

estates/mdi/mdp hostel /2017 02 march 2017 sub: renovation of … for renovation of mdp... · (j)...

Documents