eurapipe abs design manual

EURAPIPE ® ABS PIPE & FITTINGS PRODUCT CATALOGUE

PRODUCT CATALOGUE

EURAPIPE® ABS

PIPE & FITTINGS

EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE

dISclAImER

This document has been prepared by Pentair Water Solutions to assist qualified engineers and contractors in the selection of the Company’s product, and is not intended to be an exhaustive statement on pipeline design, installation or technical matters. Any conclusions, formulae and the like contained in the manual represent best estimates only and may be based on assumptions which, while reasonable may not necessarily be correct for every installation.

Successful installation depends on numerous factors outside the Company’s control, in to any person who relies on the whole or any part of this manual and excludes all liability imposed by any statute or by the general law in respect of this manual whether statements and representation in this manual are made negligently or otherwise except to the extent it is prevented by law from so doing. The manual is not an offer to trade and shall not form any part of the trading terms in any transaction. Pentair Water Solutions trading terms contain specific provisions which limit the liability of Pentair Water Solutions to the cost of replacing or repairing any defective product.

cOPYRIGHT

This manual is a publication of Pentair Water Solutions, ABN 75 087 415 745, and must not be copied or reproduced in whole or part without the Company’s prior written consent.

This manual is and shall remain as the Company’s property and shall be returned to the Company on its request. The Company reserves the right to make changes to any matter at any time without notice.

All Pentair trademarks and logos are owned by Pentair Ltd. All other brand or product names are trademarks or registered marks of their respective owners.

3



4


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

THE cOmPANY

Pentair has a highly trained and experienced team who are dedicated to the design, manufacture, installation and operation of its products.

The company is committed to a program of continuous improvement in the quality and reliability of its products and services. Technical advice is available from our engineer team. Application advice and support is also available.

Our products are manufactured to conform to recognised international engineering quality standard such as Australian Standard AS/NZS 3518 : 2004. Pantair’s is also accredited to ISO9001:2008 Quality System.

PROdUcT APPlIcATIONS

Our products are widely used in a variety of applications such as:

• HVAC, chilled water and condenser

• Water reticulation

• Domestic plumbing

• Water treatment plants

• Waste water treatment and recycling plants

• Power generation plants

• Industrial plants such as electronics, food processing, chemical, paper mills, palm oils and rubber mills.

PRESSURE RATINGS

EURAPIPE ABS piping systems are available in the following range of sizes: DN15 to DN750. Standard pressure ratings at 20oC are 900 KPa, 1200 KPa and 1500 KPa (Class C, Class D and Class E).

INTROdUcTION

ABS thermoplastics are recognized as a suitable material to be used in many industry applications.

The material is very tough and resilient, has high impact strength, good chemical resistance non-toxic and taint free.

ABS piping systems are replacing many piping systems made from other materials.

Pentair’s ABS piping systems compromises a large range of pressure ratings for pipes and fittings, joined together by cold solvent cement welding.

THE mATERIAl

Acrylonitrile – Butadiene – Styrene (ABS) identifies a family of engineering thermoplastics with a board range of performance characteristics. The copolymeric system is alloyed to yield the optimum balance of properties suited to the selected end use.

ACRYLONITRILE

imparts chemical resistance and rigidity.

BUTADIENE

endows the product with impact strength, toughness and abrasion resistance.

STYRENE

contributes to the lustre, ease of processing and rigidity.

mATERIAl PROPERTIES

The formulation of ABS used by Euratech has been developed in conjunction with polymer manufacturers to optimise performance in respect to tensile strength, chemical resistance, ductility, resistance to weathering, heat stability, low toxicity, taint free and ease processing from raw material to finished product.

ABS is tough and strong over the recommended temperature range of -30oC to +60oC.

THE OUTSTANdING PROPERTIES OF ABS ARE:

• High impact strength and ductility, which combine to give exceptional toughness.

• Good chemical resistance.

• Abrasion resistance.

• High strength solvent weld jointing which allows efficient system assembly and modification.

• Withstands aggressive ground waters.

• High strain tolerance for buried applications.

• Good resistance to ultraviolet light.

• Better flow rate.

5



ENVIRONmENTAl

The use of ABS contributes positively to the environment as it takes approximately one sixth of the energy to manufacture compared to metal products. This has direct savings in greenhouse gas emissions. Additionally ABS is lead and chlorine free and can be readily recycled.

ImPAcT STRENGTH

The butadiene constituent in ABS affords unrivalled resistance to impact. This means that EURAPIPE Piping systems may be used in more critical applications where other types of plastics could not be considered.

ABS is a ductile material and the mode of failure resembles that of soft copper. Failure is by ductile distortion and tearing, the localized nature minimizing the loss of pipe contents.

In contract, crack propagation and hazardous material fragmentation accompany the failure of brittle material.

ABRASION RESISTANcE

EURAPIPE ABS offers outstanding resistance to abrasion and erosion from aggressive slurries which can rapidly damage steel or other traditional pipe materials.

WEATHER RESISTANcE

EURAPIPE ABS is one of the most weather resistance polymers available today. Successful field tests have been completed on piping systems having been exposed to weathering for over 30 years.

lIGHT WEIGHT

ABS is one-sixth the weight of steel systems, making EURAPIPE easy to handle and install. This reduces the cost of installation, handling and transport.

cHEmIcAl RESISTANcE

EURAPIPE ABS is unaffected by both internal and external attack by a wide range of acids, alkalis, ground water salts and other environmental factors. Please refer to Pentair for further information.

QUIcK REFERENcE cHEmI-cAl REISITANcE

• Weak acids Good resistance

• Strong acids Limited resistance

• Weak alkalis Good resistance

• Strong alkalis Good resistance

• Aggressive Excellent resistance soils

• Metal salts Good resistance

• Sea water Excellent resistance

• Aromatic Poor resistance hydrocarbons

• Organic Poor resistance solvents

NON-TOXIc / TAINT FREE

The ABS formulation contains no harmful metallic stabilizers and it has been widely used for many years in piping systems for drinking water, medical preparations, food products and potable water. EURAPIPE ABS systems is ideal for potable cold water. It conforms to World Health Organisation, E.E.C. and AS4020 / BS6920 requirement for potable water reticulation and distribution.

SmOOTH BORE

EURAPIPE ABS does not suffer from internal corrosion and provides a smooth bore for the life of the piping systems. The smooth bore does not support formation of scale and slime as do cement based lined products.

cOld SOlVENT WEld JOINING

The EURAPIPE range also utilizes the proven traditional method of joining ABS pipes, cold solvent cement welding, which provides a homogenous bond/weld between pipes and fittings (SWJ).

TEmPERATURE RANGE

A great advantage of EURAPIPE ABS over other plastic systems is its ability to perform over a wide temperature range from -30°C to +60°C. This makes EURAPIPE ABS very versatile and capable of handling a wide variety of fluids from refrigerants to moderately hot corrosive liquids.

THERmAl EXPANSION

All thermoplastics expand at a greater rate than metal.

Expansion need not caused undue concern in design or installation of an ABS piping system provided that due recognition is taken at the design stage. The reduced flexural modulus of ABS over that of steel results in reduced loads on supports and equipment arising from thermal strains. The linear coefficient of thermal expansion of ABS is 10.1 x 10-5 m/m°C.

0

5

10

15

20

25

20 32 50 1002 00PI PE S IZE (mm)

IMPA

CT E

NER

GY

(Kgm

)

uPVC @ 20° C

AB S @ 0° C

AB S @20° C

6


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

DURAFLO ABS PRESSURE PIPE SERIES 1CODE PAGE 8-9

PLAIN SOCKET

CODE 100 PAGE 10

STUB FLANGE

CODE 135 PAGE 11

FULL FACE FLANGE CODE 129, 130, 317, 322

PAGE 12

SHOULDER END

CODE 954 PAGE 13

SHOULDER STYLE COUPLINGCODE 953 PAGE 14

BLANK FLANGE STUB STYLECODE 136 PAGE 15

BLANK FULL FACE FLANGECODE 131, 326, 313, 325

PAGE 16

BLIND STEEL PLATE

CODE 731, 732 PAGE 17

BLIND ABS LINER

CODE 721, 722 PAGE 18

BACKING RINGCODE 415, 416, 425, 413

PAGE 19, 20, 21 & 22

VALVE SUPPORT PLATECODE 465, 460, 470 PAGE 23

GASKET (FULL FACE STYLE)CODE 409, 410, 426 PAGE 24

GASKET(STUB FLANGE STYLE)

CODE 431 PAGE 25

ELBOW 90O

CODE 115 PAGE 26

ELBOW 45O

CODE 119 PAGE 27

FAUCET ELBOW 90O

CODE 116 PAGE 28

MOULDED BEND 90O

CODE 118 PAGE 29

BEND 90O R=1.2D (Sp-Sp)

CODE 305 PAGE 30

BEND 45º R=1.2D

CODE 304 PAGE 31

BEND 90º SHORT RADIUS

CODE 308 PAGE 32

BEND 45º SHORT RADIUS

CODE 312 PAGE 33

BEND 90º LONG RADIUS

CODE 309 PAGE 34

BEND 45º LONG RADIUS

CODE 310 PAGE 35

EQUAL TEE (So-SoxSo)

CODE 122 PAGE 36

REDUCING TEE SPIGOTOFFTAKE (So-SoxSp)

CODE 120 PAGE 37

REDUCING TEE SOCKETOFFTAKE (So-SoxSo)

CODE 122 PAGE 38

TEE THREADED OFF TAKE(So-SoxTh)

CODE 121 PAGE 39

Y PIECE 45º

CODE 128 PAGE 40

SADDLE STRIPS

CODE 146 PAGE 41

7



TAPPING SADDLES

CODE 127 PAGE 42

REDUCING SOCKET

CODE 114 PAGE 43

REDUCING BUSH

CODE 109 PAGE 44

FAUCET SOCKET

CODE 101 PAGE 45

VALVE ADAPTOR

CODE 107 PAGE 46

VALVE SOCKET

CODE 151 PAGE 47

FAUCET ADAPTOR

CODE 153 PAGE 48

CAP

CODE 140 PAGE 49

THREADED PLUG

CODE 155 PAGE 50

SOCKET UNION

CODE 205 PAGE 51

SADDLE CLIP

CODE 455 PAGE 52

PIPE CLIP

CODE 434 PAGE 53

RUBBER EXPANSION JOINT

CODE 452 PAGE 54

ANCHOR SLEEVE

CODE 272 PAGE 55

ANCHOR FLANGE

CODE 137 PAGE 56

BALL CHECK VALVE SINGLEUNION

CODE 836, 838 PAGE 57

BALL VALVE DOUBLE UNIONCODE 880, 882 PAGE 58

ABS SOLVENT CEMENT

CODE 461 PAGE 59

MEK CLEANER/PRIMER

CODE 463 PAGE 59

8


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

DURAFLO ABS PRESSURE PIPE SERIES 1SIZE/PRESSURE RATING TYPE COMPOUND

CLASSIFICATIONPRODUCT

CODEPRESSURE

(BAR)OD MEAN

(mm) WALL MEAN (mm)

ID MEAN (mm)

DN 15 S1 PN20 DURAFLO ABS160 R11.5200.015 20 21.4 2.1 17.2









DN 80 S1 PN 9 DURAFLO ABS160 R11.5090.080 9 88.9 4.1 80.7






*DN 125 S1 PN 9 DURAFLO ABS160 R11.5090.125 9 140.2 6.4 127.3












* DENOTES NON-STOCKABLE

9



PIPE COMPLIES WITH AS/NZS 3518:2004All values quoted are subject to manufacturing tolerances. Standard pipe length supplied 5.8m. Other lengths and pressure ratings are available upon request.Pipe is supplied plain ended.

DURAFLO ABS PRESSURE PIPE SERIES 1SIZE/PRESSURE RATING TYPE PRODUCT

CODEPRESSURE

(BAR)OD MEAN

(mm) WALL MEAN (mm)

ID MEAN (mm)















*DN 450 S1 PN12 DURAFLO ABS160 R11.5120.500 12 500.5 29.8 441.0











* DENOTES NON-STOCKABLE

10


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

PLAIN SOCKETSIZE CODE ID A B Z PN

(mm) (mm) (mm) (mm) RATING

DN 15 S1 R 01.100.015 21 27 43 9 15

DN 20 S1 R 01.100.020 27 33 47 7 15

DN 25 S1 R 01.100.025 34 41 53 7 15

DN 32 S1 R 01.100.032 42 52 61 7 15

DN 40 S1 R 01.100.040 48 59 65 5 15

DN 50 S1 R 01.100.050 60 74 77 5 15

DN 65 S1 R 01.100.065 75 93 91 3 15

DN 80 S1 R 01.100.080 89 110 112 10 15

DN 100 S1 R 01.100.100 114 141 138 10 15

DN 125 S1 R 01.100.125 140 168 165 12 15

DN 150 S1 R 01.100.150 168 204 192 12 15

DN 200 S1 R 11.100.225 225 250 246 8 12

DN 225 S1 R 11.100.250 250 280 271 9 12

DN 300 S1 R 11.100.315 315 355 337 9 12

DN 350 S1 R 11.100.355 355 388 377 9 12

DN 375 S1 R 11.100.400 400 440 423 11 12

DN 400 S1 R 11.100.450 450 500 476 14 12

DN 450 S1 R 11.100.500 500 560 527 15 12

DN 500 S1 R 11.100.560 560 665 555 15 12

DN 575 S1 R 11.100.630 630 708 590 20 21

DN 650 S1 R 11.100.710 710 808 630 20 9

DN 750 S2 R 11.100.826 826 922 675 15 9

COMPLIES WITH AS/NZS 3518:2004

11



STUB FLANGESIZE CODE ID A B C D Z D* A* PN

(mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) RATING

DN 50 S1 R01.***.050 60 96 40 14 74 3 74 96 15

DN 65 S1 R01.***.065 75 106 47 10 90 3 90 106 15

DN 80 S1 R01.***.080 89 127 57 18 108 5 108 127 15

DN 100 S1 R01.***.100 114 159 70 20 134 5 134 156 15

DN 125 S1 R01.***.125 140 187 84 12 163 5 163 181 15

DN 150 S1 R01.***.150 168 214 100 24 192 8 192 214 15

DN 200 S1 R11.***.225 225 270 126 25 250 6 247 267 12

DN 225 S1 R11.***.250 250 334 138 30 305 6 301 330 12

DN 300 S1 R11.***.315 315 376 171 35 362 6 350 374 12

DN 350 S1 R11.***.355 355 440 191 37 415 6 395 420 12

DN 375 S1 R11.***.400 400 488 214 35 450 8 440 483 12

DN 400 S1 R11.***.450 450 548 331 110 506 100 492 538 12

DN 450 S1 R11.***.500 500 613 356 110 561 100 544 593 12

DN 500 S1 R11.***.560 560 665 282 50 615 12 598 647 12

DN 575 S1 R11.***.630 630 708 340 65 671 55 12

DN 650 S1 R11.***.710 710 808 325 70 770 20 9

DN 750 S2 R11.***.826 826 922 430 110 870 100 9

COMPLIES WITH AS/NZS 3518:2004*CODE 134 - TO SUIT BACKING RING DRILLED TO JIS10K 138 SERIES STUB FLANGE

SIZE CODE ID A B C D Z

(mm) (mm) (mm) (mm) (mm) (mm)

200 R11.138. 225 225 270 144 35 250 250

225 R11.138. 250 250 334 191 70 305 60

300 R11.138. 315 315 376 224 70 362 60

350 R11.138. 355 355 440 244 70 415 60

375 R11.138. 400 400 488 306 110 450 100

CODE 135 - TO SUIT ALL OTHER DRILLINGS

TRADITIONAL STUB FLANGESWhen using the new compact stub flanges it will be important to determine what equipment they are matching up to. Where the flanges are being used with butterfly valves you will need to check the cordal diameter of the valve disc (the disc cord dimension at the face of the valve) to deter-mine if there will be a clash with the pipe ID. Where this is likely to occur we have the 138 series stub flange which is designed to take the potential clash into account

TECHNICAL DATASIZE RANGE: DN 200 to DN 375TEMPERATURE RANGE: -30°C to 60°CJOINTING METHODS: Solvent cement

12


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

FULL FACE FLANGE TABLE “E”SIZE CODE ID A B C D Z D* PN

(mm) (mm) (mm) (mm) (mm) (mm) (mm) RATING

DN 15 S1 R01.130.015 21 95 23 10 30 3 30 15

DN 20 S1 R01.130.020 27 100 25 10 35 3 35 15

DN 25 S1 R01.130.025 34 115 28 10 43 3 43 15

DN 32 S1 R01.130.032 42 140 32 10 52 3 52 15

DN 40 S1 R01.130.040 48 150 34 10 62 3 62 15

DN 50 S1 R01.130.050 60 165 40 10 74 3 74 15

DN 80 S1 R01.130.080 89 200 57 12 108 5 108 15

DN 100 S1 R01.130.100 114 220 70 17 134 5 134 15

DN 150 S1 R01.130.150 168 285 100 22 192 8 192 15

CODE 129 - UNDRILLED

CODE 317 - DRILLED TABLE D AS 2129:2000.CODE 322 - DRILLED ANSI 150

*CODE 329 - DRILLED JIS10K


13



SHOULDER ENDSIZE CODE ID A B Z PN


DN 50 S1 R01.954.050 60 74 70 33 15

DN 80 S1 R01.954.080 89 104 90 39 15

DN 100 S1 R01.954.100 114 141 108 45 15

DN 150 S1 R01.954.150 168 208 140 50 15

DN 200 S1 R11.954.225 225 269 170 51 12

DN 225 S1 R11.954.250 250 310 207 76 12

DN 300 S1 R11.954.315 315 355 245 81 12

DN 350 S1 R11.954.355 355 387 273 89 9

DN 375 S1 R11.954.400 400 450 307 101 9

DN 400 S1 R11.954.450 450 500 337 106 9

DN 450 S1 R11.954.500 500 560 367 111 9


14


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

SHOULDER STYLE COUPLINGTO SUIT PIPE CODE A B Z

SIZE (mm) (mm) (mm)

DN 50 S1 R03.953.050 140 98 44

DN 80 S1 R03.953.080 175 131 46

DN 100 S1 R03.953.100 205 162 50

DN 150 S1 R03.953.150 275 214 52

DN 200 S1 R13.953.225

DN 225 S1 R13.953.250 410 348 69

DN 300 S1 R13.953.315 489 395 69

DN 350 S1 R13.953.355 555 448 76

DN 375 S1 R13.953.400 568 482 73

DN 400 S1 R13.953.450 619 539 79

DN 450 S1 R13.953.500 698 597 76

MATERIAL -

CASING - GALVANIZED IRON

GASKET - EDPM

15



BLANK FLANGE STUB STYLESIZE CODE A B

(mm) (mm)

DN 200 S1 R11.136.225 270 25

DN 225 S1 R11.136.250 334 34

DN 300 S1 R11.136.315 376 40

FOR LARGER SIZES STEEL PLATES ARE RECOMMENDED* REQUIRES A BACKING RING

16


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

BLANK FULL FACE FLANGE TABLE “E”SIZE CODE A B

(mm) (mm)

DN 15 S1 R01.313.015 95 13

DN 20 S1 R01.313.020 100 13

DN 25 S1 R01.313.025 115 13

DN 32 S1 R01.313.032 140 13

DN 40 S1 R01.313.040 150 13

DN 50 S1 R01.313.050 165 13

DN 80 S1 R01.313.080 200 19

DN 100 S1 R01.313.100 220 19

DN 150 S1 R01.313.150 285 25

CODE 326 - DRILLED TABLE D / AS 2129:2000.

CODE 129 - UNDRILLEDCODE 325 - DRILLED ANSI 150

CODE 332 - DRILLED JIS10K

17



BLIND STEEL PLATE

SIZE CODE A B

(mm) (mm)

TABLE D* TABLE E*

DN 50 S1 R03.***.050 150 8 10

DN 65 S1 R03.***.065 165 8 10

DN 80 S1 R03.***.080 185 10 11

DN 100 S1 R03.***.100 215 10 12

DN 125 S1 R03.***.125 255 13 14

DN 150 S1 R03.***.150 280 13 17

DN 200 S1 R13.***.225 335 13 19

DN 225 S1 R13.***.250 405 16 22

DN 300 S1 R13.***.315 455 19 25

DN 350 S1 R13.***.355 525 22 29

DN 375 S1 R13.***.400 580 22 32

DN 400 S1 R13.***.450 640 25 35

DN 450 S1 R13.***.500 705 29 38

DN 500 S1 R13.***.560 760 29 44

DN 575 S1 R13. ***.630 825 32 48

DN 650 S1 R13.***.710 910 35 51

DN 750 S2 R13.***.826 1060 41 54

STANDARD MATERIAL - HOT DIPPED GALVANISED MILD STEEL TO AS/NZS 4680:1999.


CODE 731 - DRILLED TABLE E / AS 2129:2000.

OTHER DRILLINGS AVAILABLE ON REQUEST

* WHEN USING BLIND STEEL PLATE IT IS RECOMMENDED TO USE BLIND PLASTIC LINER AS WELL.

18


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

BLIND ABS LINER

TO SUIT PIPE CODE A B

SIZE (mm) (mm)

DN 50 S1 R01.***.050 150 3

DN 65 S1 R01.***.065 165 3

DN 80 S1 R01.***.080 185 3

DN 100 S1 R01.***.100 215 3

DN 125 S1 R01.***.125 255 3

DN 150 S1 R01.***.150 280 3

DN 200 S1 R11.***.225 335 3

DN 225 S1 R11.***.250 405 3

DN 300 S1 R11.***.315 455 3

DN 350 S1 R11.***.355 525 3

DN 375 S1 R11.***.400 580 3

DN 400 S1 R11.***.450 640 3

DN 450 S1 R11.***.500 705 3

DN 500 S1 R11.***.560 760 3

DN 575 S1 R11.***.630 825 3

DN 650 S1 R11.***.710 910 3

DN 750 S2 R11.***.826 1060 3

STANDARD MATERIAL - ABS WHITE SHEET.


CODE 721 - DRILLED TABLE E / AS 2129:2000.


* TO BE USED IN CONjUNCTION WITH BLIND STEEL PLATE

19



BACKING RING TABLE DTABLE D AS 2129:2000

TO SUIT PIPE CODE ID A B DN PCD NO OF HOLE

SIZE (mm) (mm) (mm) (mm) HOLES (mm)

DN 15 S1 R03.415.015 34 95 6 15 67 4 14

DN 20 S1 R03.415.020 40 100 6 20 73 4 14

DN 25 S1 R03.415.025 48 115 6 25 83 4 14

DN 32 S1 R03.415.032 58 120 6 32 87 4 14

DN 40 S1 R03.415.040 64 135 6 40 98 4 14

DN 50 S1 R03.415.050 79 150 8 50 114 4 18

DN 65 S1 R03.415.065 92 165 8 65 127 4 18

DN 80 S1 R03.415.080 112 185 8 80 146 4 18

DN 100 S1 R03.415.100 139 215 8 100 178 4 18

DN 125 S1 R03.415.125 167 255 10 125 210 8 18

DN 150 S1 R03.415.150 196 280 10 150 235 8 18

DN 200 S1 R13.415.225 258 335 10 200 292 8 18

DN 225 S1 R13.415.250 310 405 20 250 356 8 22

DN 300 S1 R13.415.315 366 455 20 300 406 12 22

DN 350 S1 R13.415.355 420 525 20 350 470 12 26

*DN 375 S1 R13.415.400 454 580 20 *400 521 12 26

*DN 400 S1 R13.415.450 510 640 25 *450 584 12 26

*DN 450 S1 R13.415.500 565 705 30 *500 641 16 26

*DN 500 S1 R13.415.560 621 760 30 *550 699 16 30

*DN 575 S1 R13.415.630 675 825 32 *600 756 16 30

*DN 650 S1 R13.415.710 775 910 35 *700 845 20 30

*DN 750 S2 R13.415.826 902 1060 41 *800 984 20 36


AVAILABLE IN STAINLESS STEEL ON REQUEST - CODE 422


*WHEN CONNECTING ABS SYSTEMS TO OTHER SYSTEMS PLEASE NOTE VARIATION BETWEEN ABS SYSTEM “DN” DESIGNATION AND AS 2129 “DN” DESIGNATION

20


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

BACKING RING TABLE E

TABLE E AS 2129:2000



DN 15 S1 R03.416.015 34 95 6 15 67 4 14

DN 20 S1 R03.416.020 40 100 6 20 73 4 14

DN 25 S1 R03.416.025 48 115 6 25 83 4 14

DN 32 S1 R03.416.032 58 120 6 32 87 4 14

DN 40 S1 R03.416.040 64 135 6 40 98 4 14

DN 50 S1 R03.416.050 79 150 8 50 114 4 18

DN 65 S1 R03.416.065 92 165 8 65 127 4 18

DN 80 S1 R03.416.080 112 185 8 80 146 4 18

DN 100 S1 R03.416.100 139 215 8 100 178 8 18

DN 125 S1 R03.416.125 167 255 10 125 210 8 18

DN 150 S1 R03.416.150 196 280 10 150 235 8 22

DN 200 S1 R13.416.225 258 335 10 200 292 8 22

DN 225 S1 R13.416.250 310 405 20 250 356 12 22

DN 300 S1 R13.416.315 366 455 20 300 406 12 26

DN 350 S1 R13.416.355 420 525 20 350 470 12 26

*DN 375 S1 R13.416.400 454 580 20 *400 521 12 26

*DN 400 S1 R13.416.450 510 640 25 *450 584 16 26

*DN 450 S1 R13.416.500 565 705 30 *500 641 16 26

*DN 500 S1 R13.416.560 621 760 30 *550 699 16 30

*DN 575 S1 R13.416.630 675 825 32 *600 756 16 33

*DN 650 S1 R13.416.710 775 910 35 *700 845 20 33

*DN 750 S2 R13.416.826 902 1060 41 *800 984 20 36




*WHEN CONNECTING ABS SYSTEMS TO OTHER SYSTEMS PLEASE NOTE VARIATION BETWEEN ABS SYSTEM “DN” DESIGNATION AND AS 2129 “DN” DESIGNATION

21



BACKING RING ANSI150

ANSI 150



DN 15 S1 R03.425.015 34 95 6 15 60 4 15

DN 20 S1 R03.425.020 40 100 6 20 70 4 15

DN 25 S1 R03.425.025 48 115 6 25 79 4 15

DN 32 S1 R03.425.032 58 120 6 32 89 4 15

DN 40 S1 R03.425.040 64 135 6 40 98 4 15

DN 50 S1 R03.425.050 79 150 8 50 121 4 18

DN 65 S1 R03.425.065 92 165 8 65 140 4 18

DN 80 S1 R03.425.080 112 185 8 80 152 4 18

DN 100 S1 R03.425.100 139 215 8 100 191 8 18

DN 125 S1 R03.425.125 167 255 10 125 216 8 21

DN 150 S1 R03.425.150 196 280 10 150 241 8 21

DN 200 S1 R13.425.225 258 335 10 200 298 8 21

DN 225 S1 R13.425.250 310 405 20 250 362 12 25

DN 300 S1 R13.425.315 366 455 20 300 432 12 25

DN 350 S1 R13.425.355 420 525 20 350 476 12 28

DN 375 S1 R13.425.400 454 580 20 400 540 16 30




22


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

BACKING RING JIS10K

JIS 10K



DN 15 S1 R03.413.015 34 95 6 15 70 4 14

DN 20 S1 R03.413.020 40 100 6 20 75 4 14

DN 25 S1 R03.413.025 48 125 6 25 90 4 18

DN 32 S1 R03.413.032 58 135 6 32 100 4 18

DN 40 S1 R03.413.040 64 140 6 40 105 4 18

DN 50 S1 R03.413.050 79 155 8 50 120 4 18

DN 65 S1 R03.413.065 92 175 8 65 140 4 18

DN 80 S1 R03.413.080 112 185 8 80 150 8 18

DN 100 S1 R03.413.100 139 210 8 100 175 8 18

DN 125 S1 R03.413.125 167 250 10 125 210 8 22

DN 150 S1 R03.413.150 196 280 10 150 240 8 22

DN 200 S1 R13.413.225 258 330 10 200 290 12 22

DN 225 S1 R13.413.250 310 400 20 250 355 12 24

DN 300 S1 R13.413.315 366 445 20 300 400 16 24

DN 350 S1 R13.413.355 420 490 20 350 445 16 24

*DN 375 S1 R13.413.400 454 560 20 *400 510 16 26

*DN 400 S1 R13.413.450 510 620 25 *450 565 20 26

*DN 450 S1 R13.413.500 565 675 30 *500 620 20 26

*DN 500 S1 R13.413.560 621 745 30 *550 680 20 32




*WHEN CONNECTING ABS SYSTEMS TO OTHER SYSTEMS PLEASE NOTE VARIATION BETWEEN ABS SYSTEM “DN” DESIGNATION AND JIS 10K “DN” DESIGNATION

23



VALVE SUPPORT PLATE

TO SUIT PIPE CODE A B C D E F

SIZE (mm) (mm) (mm) (mm) (mm) (mm)

DN 15 S1 R03.***.015 95 86 51 14 16 8

DN 20 S1 R03.***.020 100 89 76 14 16 8

DN 25 S1 R03.***.025 115 95 76 14 16 8

DN 32 S1 R03.***.032 120 99 76 14 16 8

DN 40 S1 R03.***.040 135 105 76 14 16 8

DN 50 S1 R03.***.050 150 127 102 14 22 8

DN 65 S1 R03.***.065 165 143 115 14 22 8

DN 80 S1 R03.***.080 185 143 126 14 22 8

DN 100 S1 R03.***.100 215 159 152 14 22 8

DN 125 S1 R03.***.125 255 185 190 14 30 10

DN 150 S1 R03.***.150 280 216 230 18 33 10

DN 200 S1 R13.***.225 335 248 280 18 33 10

DN 225 S1 R13.***.250 405 298 340 22 40 12

DN 300 S1 R13.***.315 455 348 390 22 40 12

STANDARD MATERIAL - HOT DIPPED GALVANISED MILD STEEL TO AS/NZS 4680


CODE 460 - DRILLED TABLE E / AS 2129:2000.CODE 470 - DRILLED TO ANSI 150


AVAILABLE IN STAINLESS STEEL ON REQUEST.

24


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

GASKET (FULL FACE STYLE)

SIZE CODE ID A B

(mm) (mm) (mm)

DN 15 S1 R04.***.015 22 95 3

DN 20 S1 R04.***.020 28 100 3

DN 25 S1 R04.***.025 35 115 3

DN 32 S1 R04.***.032 43 120 3

DN 40 S1 R04.***.040 49 135 3

DN 50 S1 R04.***.050 61 150 3

DN 80 S1 R04.***.080 90 185 3

DN 100 S1 R04.***.100 115 215 3

DN 150 S1 R04.***.150 169 280 3

DN 200 S1 R14.***.225 226 335 8

DN 225 S1 R14.***.250 251 405 8

DN 300 S1 R14.***.315 316 455 8

DN 350 S1 R14.***.355 356 535 8

DN 375 S1 R14.***.400 401 580 8

DN 400 S1 R14.***.450 451 640 8

DN 450 S1 R14.***.500 501 705 8

DN 500 S1 R14.***.560 561 760 8

DN 575 S1 R14.***.630 631 825 8

DN 650 S1 R14.***.710 711 910 8

DN 750 S2 R14.***.826 827 1060 8

STANDARD MATERIAL - EDPM. OTHER MATERIALS ARE AVAILABLE ON REQUEST

CODE 409 - DRILLED TABLE D* / AS 2129:2000.

CODE 410 - DRILLED TABLE E* / AS 2129:2000.

CODE 426 - DRILLED TO ANSI 150*


*SEE NOTES AND DRILLING DETAILS ON PAGES 19, 20, 21 & 22

25



GASKET (STUB FLANGE STYLE)

SIZE CODE ID A B

(mm) (mm) (mm)

DN 50 S1 R04.431.050 61 97 3

DN 65 S1 R04.431.065 76 105 3

DN 80 S1 R04.431.080 90 129 3

DN 100 S1 R04.431.100 115 161 3

DN 125 S1 R04.431.125 141 187 3

DN 150 S1 R04.431.150 169 214 3

26


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

ELBOW 90º

SIZE CODE ID B Z PN

(mm) (mm) (mm) RATING

DN 15 S1 R01.115.015 21 31 11 15

DN 20 S1 R01.115.020 27 36 14 15

DN 25 S1 R01.115.025 34 43 18 15

DN 32 S1 R01.115.032 42 51 22 15

DN 40 S1 R01.115.040 48 56 25 15

DN 50 S1 R01.115.050 60 69 32 15

DN 65 S1 R01.115.065 75 83 39 15

DN 80 S1 R01.115.080 89 102 50 15

DN 100 S1 R01.115.100 114 147 71 15

DN 125 S1 R01.115.125 140 180 96 15

DN 150 S1 R01.115.150 168 180 88 15

DN 200 S1 R11.115.225 225 235 116 12

DN 225 S1 R11.115.250V 250 258 127 12

DN 300 S1 R11.115.315V 315 322 158 12

DN 350 S1 R11.115.355R 355 507 323 9

DN 375 S1 R11.115.400V 400 507 300 9


ELBOW DN350 IS MANUFACTURED FROM ELBOW DN375 FITTED WITH DN375-DN350 REDUCING BUSHES

FOR DN200 AND ABOVE, ELBOWS WITH HIGHER PRESSURE RATINGS ARE AVAILABLE.THEY ARE MANUFACTURED FROM ABS LAYERED WITH GLASS REINFORCED EPOXY AND ARE DESIGNED AND MANUFACTURED IN ACCORDANCE TO EURAPIPE INTERNAL QUALITY AND MANUFACTURING PROCEDURES AND SPECIFICATIONS AND TYPE TESTED AT 3.2 TIMES THE DESIGN PRESSURE.

27



ELBOW 45º

SIZE CODE ID B Z PN


DN 15 S1 R01.119.015 21 27 7 15

DN 20 S1 R01.119.020 27 30 8 15

DN 25 S1 R01.119.025 34 35 10 15

DN 32 S1 R01.119.032 42 42 13 15

DN 40 S1 R01.119.040 48 45 14 15

DN 50 S1 R01.119.050 60 54 17 15

DN 65 S1 R01.119.065 75 61 17 15

DN 80 S1 R01.119.080 89 74 21 15

DN 100 S1 R01.119.100 114 94 28 15

DN 125 S1 R01.119.125 140 107 31 15

DN 150 S1 R01.119.150 168 132 40 15

DN 200 S1 R11.119.225V 225 171 52 12

DN 225 S1 R11.119.250V 250 190 58 12

DN 300 S1 R11.119.315V 315 232 68 12

DN 350 S1 R11.119.355R 355 294 110 9

DN 375 S1 R11.119.400V 400 294 87 9


ELBOW DN350 IS MANUFACTURED FROM ELBOW DN375 FITTED WITH DN375-DN350 REDUCING BUSHES

FOR DN200 AND ABOVE, ELBOWS WITH HIGHER PRESSURE RATINGS ARE AVAILABLE.THEY ARE MANUFACTURED FROM ABS LAYERED WITH GLASS REINFORCED EPOXY AND ARE DESIGNED AND MANUFACTURED IN ACCORDANCE TO EURAPIPE INTERNAL QUALITY AND MANUFACTURING PROCEDURES AND SPECIFICATIONS AND TYPE TESTED AT 3.2 TIMES THE DESIGN PRESSURE.

28


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

FAUCET ELBOW 90º

SIZE SIZE CODE A B C D ID Z PN

SW SOCKET THREADED (mm) (mm) (mm) (mm) (mm) (mm) RATING

DN 15 S1 1/2” BSP R01.116.015 29 29 31 18 21 11 15

DN 20 S1 3/4” BSP R01.116.020 35 35 36 21 27 14 15

DN 25 S1 1” BSP R01.116.025 44 42 43 24 34 18 15

DN 20 S1 1/2” BSP R01.116.020015 35 32 36 18 27 14 15


29



MOULDED BEND 90º

SIZE CODE ID A B C L PN

(mm) (mm) (mm) (mm) (mm) RATING

DN 15 S1 R01.118.015 21 29 40 58 20 15

DN 20 S1 R01.118.020 27 35 50 71 22 15

DN 25 S1 R01.118.025 34 43 64 88 25 15

DN 32 S1 R01.118.032 42 54 80 109 29 15

DN 40 S1 R01.118.040 48 64 100 131 31 15

DN 50 S1 R01.118.050 60 76 126 163 37 15

DN 65 S1 R01.118.065 75 93 150 195 44 15

DN 80 S1 R01.118.080 89 113 180 231 53 15

DN 100 S1 R01.118.100 114 137 220 284 65 15


30


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

BEND 90º R=1.2D (So- So)SIZE CODE A B PN

(mm) min(mm) RATING

DN 400 S1 PN 9 R11.305090.450 1142 1387 9

DN 450 S1 PN 9 R11.305090.500 1235 1506 9

DN 500 S1 PN 9 R11.305090.560 1272 1557 9

DN 575 S1 PN 9 R11.305090.630 1300 1605 9

DN 650 S1 PN 9 R11.305090.710 1593 1918 9

DN 750 S2 PN 9 R11.305090.826 1752 2097 9

A=MINIMUM LEG LENGTHMANUFACTURING TOLERANCES APPLY

OTHER ANGLES ARE AVAILABLE UPON REQUEST

THE FOLLOWING ADDITIONAL BEND PRESSURE RATINGS ARE AVAILABLE UPON REQUEST:

CODE 305045 PN 4.5

CODE 305060 PN 6

CODE 305120 PN 12

THE BENDS ARE MANUFACTURED FROM ABS LAYERED WITH GLASS REINFORCED EPOXY.

THEY ARE DESIGNED AND MANUFACTURED IN ACCORDANCE TO EURAPIPE INTERNAL QUALITY AND MANUFACTURING PROCEDURES AND SPECIFICATIONS AND TYPE TESTED AT 3.2 TIMES THE DESIGN PRESSURE.

31



BEND 45º R=1.2D (So- So)SIZE CODE A B PN

(mm) min(mm) RATING

DN 400 S1 PN 9 R11.304090.450 878 1123 9

DN 450 S1 PN 9 R11.304090.500 969 1241 9

DN 500 S1 PN 9 R11.304090.560 1134 1419 9

DN 575 S1 PN 9 R11.304120.630 1153 1458 9

DN 650 S1 PN 9 R11.304090.710 1429 1754 9

DN 750 S2 PN 9 R11.304090.826 1396 1741 9




CODE 304045 PN 4.5

CODE 304060 PN 6

CODE 304120 PN 12

THE BENDS ARE MANUFACTURED FROM ABS LAYERED WITH GLASS REINFOCED EPOXY.

THEY ARE DESIGNED AND MANUFACTURED IN ACCORDANCE TO EURAPIPE INTERNAL QUALITY AND MANUFACTURING PROCEDURES AND SPECIFICATIONS AND TYPE TESTED AT 3.2 TIMES THE DESIGN PRESSURE.

32


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

BEND 90º SHORT RADIUS R=2.5D (Sp- Sp)SIZE CODE A B PN

(mm) min(mm) RATING

DN 50 S1 PN 15 R01.308150.050 208 251 15

DN 65 S1 PN 15 R01.308150.065 252 288 15

DN 80 S1 PN 15 R01.308150.080 295 327 15

DN 100 S1 PN 15 R01.308150.100 371 416 15

DN 125 S1 PN 15 R01.308150.125 447 503 15

DN 150 S1 PN 15 R01.308150.150 532 604 15

DN 200 S1 PN 9 R11.308090.225 800 947 9

DN 225 S1 PN 9 R11.308090.250 887 960 9

DN 300 S1 PN 9 R11.308090.315 1115 1215 9

DN 350 S1 PN 9 R11.308090.355 1255 1355 9

DN 375 S1 PN 9 R11.308090.400 1411 1511 9

DN 400 S1 PN 9 R11.308090.450 1586 1686 9

*DN 450 S1 PN 9 R11.308090.500 2019 2290 9




ALL SIZES CODE 308045

ALL SIZES CODE 308060

DN50 TO DN150 CODE 308120

* DN450 BENDS ARE MANUFACTURED FROM ABS LAYERED WITH GLASS REINFOCED EPOXY AND ARE SUPPLYED COMPLETE WITH SOCKETS AT BOTH ENDS. THEY ARE DESIGNED AND MANUFACTURED IN ACCORDANCE TO EURAPIPE INTERNAL QUALITY AND MANUFACTURING PROCEDURES AND SPECIFICATIONS AND TYPE TESTED AT 3.2 TIMES THE DESIGN PRESSURE. BENDS SUPPLIED PLAIN ENDED, REQUIRE SOCKETS OR STUB & B/RING FOR JOINING.

33



BEND 45º SHORT RADIUS R=2.5D (Sp- Sp)

SIZE CODE A B PN

(mm) min(mm) RATING

DN 50 S1 PN 15 R01.312150.050 119 212 15

DN 65 S1 PN 15 R01.312150.065 142 254 15

DN 80 S1 PN 15 R01.312150.080 165 267 15

DN 100 S1 PN 15 R01.312150.100 203 318 15

DN 125 S1 PN 15 R01.312150.125 241 385 15

DN 150 S1 PN 15 R01.312150.150 286 434 15

DN 200 S1 PN 12 R11.312120.225 471 753 12

DN 225 S1 PN 12 R11.312120.250 521 839 12

DN 300 S1 PN 12 R11.312120.315 654 936 12

DN 350 S1 PN 12 R11.312120.355 736 1083 12

DN 375 S1 PN 12 R11.312120.400 826 1214 12

DN 400 S1 PN 12 R11.312120.450 928 1374 12

*DN 450 S1 PN 12 R11.312120.500 2050 1678 12




CODE 312045 PN 4.5

CODE 312060 PN 6

CODE 312090 PN 9

* DN450 BENDS ARE MANUFACTURED FROM ABS LAYERED WITH GLASS REINFOCED EPOXY AND ARE SUPPLYED COMPLETE WITH SOCKETS AT BOTH ENDS. THEY ARE DESIGNED AND MANUFACTURED IN ACCORDANCE TO EURAPIPE INTERNAL QUALITY AND MANUFACTURING PROCEDURES AND SPECIFICATIONS AND TYPE TESTED AT 3.2 TIMES THE DESIGN PRESSURE. BENDS SUPPLIED PLAIN ENDED, REQUIRE SOCKETS OR STUB & B/RING FOR JOINING.

34


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

BEND 90º LONG RADIUS R= 5D (Sp-Sp)

SIZE CODE A B PN

(mm) min(mm) RATING

DN 50 S1 PN 15 R01.309150.050 357 570 15

DN 65 S1 PN 15 R01.309150.065 439 845 15

DN 80 S1 PN 15 R01.309150.080 523 870 15

DN 100 S1 PN 15 R01.309150.100 655 950 15

DN 125 S1 PN 15 R01.309150.125 796 970 15

DN 150 S1 PN 15 R01.309150.150 952 1165 15

DN 200 S1 PN 12 R11.309120.225 1264 1495 12

DN 225 S1 PN 12 R11.309120.250 1401 1615 12

DN 300 S1 PN 12 R11.309120.315 1758 2024 12

DN 350 S1 PN 12 R11.309120.355 1978 2274 12

DN 375 S1 PN 12 R11.309120.400 2226 2600 12


OTHER ANGLES AND PRESSURE RATINGS ARE AVAILABLE UPON REQUEST* BENDS SUPPLIED PLAIN ENDED, REQUIRE SOCKETS OR STUB & B/RING FOR JOINING.

35



BEND 45º LONG RADIUS R=5D (Sp-Sp)SIZE CODE A B PN

(mm) min(mm) RATING

DN 50 S1 PN 15 R01.310150.050 181 514 15

DN 65 S1 PN 15 R01.310150.065 219 756 15

DN 80 S1 PN 15 R01.310150.080 259 776 15

DN 100 S1 PN 15 R01.310150.100 321 806 15

DN 125 S1 PN 15 R01.310150.125 386 830 15

DN 150 S1 PN 15 R01.310150.150 460 968 15

DN 200 S1 PN 12 R11.310120.225 605 1276 12

DN 225 S1 PN 12 R11.310120.250 668 1357 12

DN 300 S1 PN 12 R11.310120.315 836 1622 12

DN 350 S1 PN 12 R11.310120.355 939 1870 12

DN 375 S1 PN 12 R11.310120.400 1054 2078 12


OTHER ANGLES AND PRESSURE RATINGS ARE AVAILABLE UPON REQUEST* BENDS SUPPLIED PLAIN ENDED, REQUIRE SOCKETS OR STUB & B/RING FOR JOINING.

36


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

EQUAL TEE (So-SoxSo)

SIZE CODE ID A B L Z TYPE PN


DN 15 S1 R01.122.015 21 63 31 20 11 M 15

DN 20 S1 R01.122.020 27 72 36 22 14 M 15

DN 25 S1 R01.122.025 34 85 43 25 18 M 15

DN 32 S1 R01.122.032 42 102 51 29 22 M 15

DN 40 S1 R01.122.040 48 112 56 31 25 M 15

DN 50 S1 R01.122.050 60 137 69 37 32 M 15

DN 65 S1 R01.122.065 75 166 83 44 39 M 15

DN 80 S1 R01.122.080 89 204 102 53 49 M 15

DN 100 S1 R01.122.100 114 258 129 65 64 M 15

DN 125 S1 R01.122.125 140 298 149 76 73 F 15

DN 150 S1 R01.122.150 168 360 180 92 88 M 15

DN 200 S1 R11.122.225V 225 463 232 119 113 M 12

DN 225 S1 R11.122.250V 250 526 263 131 132 M 12

DN 300 S1 R11.122.315V 315 644 322 164 158 M 12

DN 350 S1 R11.122.355 355 840 420 184 236 F 6

DN 375 S1 R11.122.400V 400 840 420 206 214 M 6


TEE DN350 IS MANUFACTURED FROM TEE DN375 FITTED WITH DN375-DN350 REDUCING BUSHES

FOR DN200 AND ABOVE, TEES WITH HIGHER PRESSURE RATINGS ARE AVAILABLE.THEY ARE MANUFACTURED FROM ABS LAYERED WITH GLASS REINFORCED EPOXY AND ARE DESIGNED AND MANUFACTURED IN ACCORDANCE TO EURAPIPE INTERNAL QUALITY AND MANUFACTURING PROCEDURES AND SPECIFICATIONS AND TYPE TESTED AT 3.2 TIMES THE DESIGN PRESSURE.

37



REDUCING TEE SPIGOT OFFTAKE (So-SoxSp)

SIZE CODE ID A B C L PN


DN 200–DN 150 R11.120.225150 225 315 500 250 120 12

DN 225–DN 150 R11.120.250150 250 339 500 325 131 12

DN 300–DN 200 R11.120.315225 315 400 650 375 164 12

DN 350–DN 225 R11.120.355250 355 450 720 450 184 12

DN 375–DN 225 R11.120.400250 400 500 800 450 206 12

DN 400–DN 350 R11.120.450355 450 560 920 657 231 12

DN 450–DN 350 R11.120.500355 500 613 1000 575 256 12

DN 500–DN 375 R11.120.560400 560 665 1200 625 270 12

DN 575–DN 375 R11.120.630400 630 708 1300 625 285 12

DN 650–DN 400 R11.120.710450 710 808 1400 680 305 9

DN 750–DN 450 R11.120.826500 826 922 1500 775 330 9


MAXIMUM ALLOWABLE SPIGOT DIAMETER IS SHOWN. REDUCERS TO SMALLER DIAMETER SPIGOTS ARE AVAILABLE UPON REQUEST

38


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

REDUCING TEE SOCKET OFFTAKE (So-SoxSo)

SIZE CODE A B C ID1 ID2 Z1 Z2 PN


DN 20–DN 15 R01.122.020015 33 67 34 27 21 12 14 15

DN 25–DN 15 R01.122.025015 41 73 38 34 21 12 18 15

DN 25–DN 20 R01.122.025020 41 78 40 34 27 14 18 15

DN 40–DN 25 R01.122.040025 59 97 50 48 34 18 25 15

DN 50–DN 25 R01.122.050025 74 109 56 60 34 18 31 15

DN 50–DN 40 R01.122.050040 74 125 62 60 48 26 31 15


39



TEE THREADED OFF TAKE (So-SoxTh)

SIZE SIZE CODE ID A B C D Z PN

SW SOCKET THREADED (mm) (mm) (mm) (mm) (mm) (mm) RATING

DN 15 S1 1/2” BSP R01.121.015 21 29 63 29 18 11 15

DN 20 S1 1/2” BSP R01.121.020015 27 35 67 32 18 12 15

DN 20 S1 3/4” BSP R01.121.020 27 44 72 35 21 14 15

DN 25 S1 1/2” BSP R01.121.025015 34 35 73 35 18 12 15

DN 25 S1 1” BSP R01.121.025 34 44 85 42 24 18 15


40


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

Y PIECE 45º

SIZE CODE ID B C Z1 Z2 Z3 TYPE* PN

(mm) (mm) (mm) (mm) (mm) (mm) RATING

DN 20 S1 R01.128.020 27 68 43 34 26 6 M 15

DN 25 S1 R01.128.025 34 81 52 55 29 7 M 15

DN 32 S1 R01.128.032 42 98 65 52 42 9 M 15

DN 40 S1 R01.128.040 48 117 77 65 51 11 M 15

DN 50 S1 R01.128.050 60 140 95 78 63 12 M 15

DN 80 S1 R01.128.080 89 290 203 189 152 27 F 6

DN 100 S1 R01.128.100 114 596 373 469 310 170 F 6

DN 150 S1 R01.128.150 168 814 495 634 405 229 F 6


41



SADDLE STRIPS

SIZE CODE ∝ A D*

( º ) (mm)

DN 80 S1 R01.146.080 120º 300 1/2”

DN 100 S1 R01.146.100 120º 300 1”

DN 125 S1 R01.146.125 120º 300 1”

DN 150 S1 R01.146.150 120º 300 1 1/4”

DN 200 S1 R11.146.225 60º 300 1 1/4”

DN 225 S1 R11.146.250 60º 300 1 1/2”

DN 300 S1 R11.146.315 60º 300 1 1/2”

DN 350 S1 R11.146.355 60º 300 1 1/2”

DN 375 S1 R11.146.400 60º 300 1 1/2”

DN 400 S1 R11.146.450 60º 300 1 1/2”

DN 450 S1 R11.146.500 60º 300 1 1/2”

D-MAXIMUM SIZE OF THE THREADED TAPPING* SADDLE STRIP SUPPLIED WITH STAINLESS STEEL STRAPS

42


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

TAPPING SADDLES

SIZE SIZE CODE A B ID1 ID2 C D L PN

MAIN OFFTAKE (mm) (mm) (mm) (mm) (mm) (mm) (mm) RATING

DN 80 S1 DN 50 S1 R01.127.080050 150 96 89 60 145 90 37 9

DN 100 S1 DN 50 S1 R01.127.100050 175 108 114 60 170 100 37 9


43



REDUCING SOCKET

SIZE CODE A A1 B ID ID1 L L1 Z TYPE PN

(mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) RATING

DN 20 - DN 15 S1 R01.114.020015 34 27 46 27 21 22 20 4 M 15

DN 25 - DN 15 S1 R01.114.025015 42 27 52 34 21 25 20 7 M 15

DN 25 - DN 20 S1 R01.114.025020 42 34 52 34 27 25 22 5 M 15

DN 32 - DN 25 S1 R01.114.032025 52 43 64 42 34 29 25 10 M 15

DN 40 - DN 25 S1 R01.114.040025 59 43 71 48 34 31 25 15 M 15

DN 40 - DN 32 S1 R01.114.040032 59 52 68 48 42 31 29 8 M 15

DN 50 - DN 40 S1 R01.114.050040 74 62 81 60 48 37 31 13 M 15

DN 65 - DN 50 S1 R01.114.065050 93 94 94 75 60 44 37 9 F 15

DN 80 - DN 50 S1 R01.114.080050 110 74 112 89 60 53 37 23 M 15

DN 80 - DN 65 S1 R01.114.080065 110 112 112 89 75 53 44 17 F 15

DN 100 - DN 80 S1 R01.114.100080 134 108 133 114 89 65 53 29 M 15

DN 125 - DN 100 S1 R01.114.125100 173 165 165 140 114 76 65 32 F 9

DN 150 - DN 100 S1 R01.114.150100 204 141 204 168 114 92 65 51 M 15

DN 150 - DN 125 S1 R01.114.150125 204 192 192 168 140 92 76 19 F 15

DN 200 - DN 150 S1 R11.114.225150 247 - 246 225 168 119 92 35 F 12

DN 200 - DN 195 S1 R11.114.225195 247 - 246 225 219 119 116 20 F 12

DN 225 - DN 200 S1 R11.114.250225 275 - 271 250 225 131 119 21 F 12

DN 300 - DN 225 S1 R11.114.315250 344 − 357 315 250 164 131 39 F 12

DN 350 - DN 300 S1 R11.114.355315 388 - 377 355 315 184 164 26 F 9

DN 375 - DN 350 S1 R11.114.400355 440 - 423 400 355 206 184 30 F 9

DN 400 - DN 375 S1 R11.114.450400 493 - 476 450 400 231 206 35 F 9

DN 450 - DN 400 S1 R11.114.500450 548 - 527 500 450 256 231 35 F 9

DN 500 - DN 450 S1 R11.114.560500 612 - 555 560 500 270 256 12 F 9

DN 575 - DN 500 S1 R11.114.630560 708 - 590 630 560 285 270 51 F 9

DN 650 - DN 575 S1 R11.114.710630 808 - 625 710 630 305 285 45 F 9

DN 750 - DN 650 S2/S1 R11.114.826710 922 - 675 826 710 330 305 30 F 9


44


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

REDUCING BUSH

SIZE CODE ID A B Z PN


DN 20 - DN 15 S1 R01.109.020015 21 27 22 2 15DN 25 - DN 15 S1 R01.109.025015 21 34 25 5 15DN 25 - DN 20 S1 R01.109.025020 27 34 25 3 15DN 32 - DN 15 S1 R01.109.032015 21 42 29 9 15DN 32 - DN 20 S1 R01.109.032020 27 42 29 7 15DN 32 - DN 25 S1 R01.109.032025 34 42 29 4 15DN 40 - DN 15 S1 R01.109.040015 21 48 31 11 15DN 40 - DN 20 S1 R01.109.040020 27 48 31 9 15DN 40 - DN 25 S1 R01.109.040025 34 48 31 6 15DN 40 - DN 32 S1 R01.109.040032 42 48 31 2 15DN 50 - DN 25 S1 R01.109.050025 34 60 37 12 15DN 50 - DN 32 S1 R01.109.050032 42 60 37 8 15DN 50 - DN 40 S1 R01.109.050040 48 60 37 6 15DN 65 - DN 50 S1 R01.109.065050 60 75 44 8 15DN 80 - DN 20 S1 R01.109.080020 27 89 52 30 15DN 80 - DN 40 S1 R01.109.080040 48 89 52 21 15DN 80 - DN 50 S1 R01.109.080050 60 89 52 15 15DN 80 - DN 65 S1 R01.109.080065 75 89 52 6 15DN 100 - DN 50 S1 R01.109.100050 60 114 64 28 15DN 100 - DN 80 S1 R01.109.100080 89 114 64 13 15DN 125 - DN 100 S1 R01.109.125100 114 140 83 20 15DN 150 - DN 100 S1 R01.109.150100 114 168 92 27 15DN 150 - DN 125 S1 R01.109.150125 140 168 92 7 15DN 200 - DN 150 S1 R11.109.225150 168 225 120 29 12DN 225 - DN 200 S1 R11.109.250225 225 250 131 12 12DN 300 - DN 225 S1 R11.109.315250 250 315 164 33 12DN 350 - DN 300 S1 R11.109.355315 315 355 184 20 12DN 375 - DN 350 S1 R11.109.400355 355 400 206 22 12DN 400 - DN 375 S1 R11.109.450400 400 450 231 25 12DN 450 - DN 400 S1 R11.109.500450 450 500 256 25 12DN 500 - DN 450 S1 R11.109.560500 500 560 270 14 12DN 575 - DN 500 S1 R11.109.630560 560 630 285 15 12DN 650 - DN 575 S1 R11.109.710630 630 710 305 20 9

DN 750 - DN 650 S2/S1 R11.109.826710 710 826 330 20 9

COMPLIES WITH AS/NZS3518:2004

45



FAUCET SOCKET (PLAIN THREADED SOCKET)

SIZE SIZE SIZE CODE A B C ID L OD Z PN

SW SOCKET THREAD SPIGOT (mm) (mm) (mm) (mm) (mm) (mm) (mm) RATING

DN 15 S1 1/2” BSP DN 20 S1 R01.101.015 32 41 18 21 20 27 19 15

DN 20 S1 3/4” BSP DN 25 S1 R01.101.020 38 47 21 27 22 34 22 15

DN 25 S1 1” BSP DN 32 S1 R01.101.025 47 54 24 34 25 42 25 15

DN 32 S1 1 1/4” BSP - R01.101.032 57 61 28 42 29 - - 15

DN 40 S1 1 1/2” BSP DN 50 S1 R01.101.040 65 66 28 48 31 60 29 15

DN 50 S1 2” BSP - R01.101.050 80 73 31 60 37 - - 15

COMPLIES WITH AS3518:2004

46


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

VALVE ADAPTOR (PLAIN THREADED NIPPLE)

SIZE SIZE SIZE CODE A B C ID OD Z1 Z PN

SW SPIGOT THREAD SW SOCKET


DN 15 S1 1/2” - R01.107.015 27 41 15 - 21 - 21 15

DN 20 S1 3/4” DN 15 S1 R01.107.020 36 46 17 21 27 26 24 15

DN 25 S1 1” DN 20 S1 R01.107.025 43 51 19 27 34 29 26 15

DN 32 S1 1 1/4” DN 25 S1 R01.107.032 52 59 22 34 42 34 30 15

DN 40 S1 1 1/2” - R01.107.040 59 62 22 - 48 - 31 15

DN 50 S1 2” DN 40 S1 R01.107.050 74 73 26 48 60 36 36 15

REDUCING VALVE ADAPTOR (REDUCING PLAIN THREADED NIPPLE)

SIZE SIZE SIZE CODE A B C ID OD Z1 Z PN

SW SPIGOT THREAD SW SOCKET


DN 20 S1 1/2” DN 15 S1 R01.107.020015 27 43 15 21 27 19 21 15

DN 25 S1 1/2” DN 20 S1 R01.107.025015 27 47 15 27 34 25 22 15

DN 25 S1 3/4” DN 20 S1 R01.107.025020 36 49 17 27 34 27 24 15

DN 32 S1 1” DN 25 S1 R01.107.032025 43 55 19 34 42 30 26 15

DN 40 S1 1” - R01.107.040025 43 58 19 - 48 - 27 15

DN 40 S1 1 1/4” - R01.107.040032 52 61 22 - 48 - 30 15

DN 50 S1 1” DN 25 S1 R01.107.050025 43 64 19 48 60 33 27 15

DN 50 S1 1 1/2” DN 40 S1 R01.107.050040 59 68 22 48 60 27 31 15


47



VALVE SOCKET (MALE ADAPTOR)

SIZE SIZE CODE A B C ID Z PN

SW SOCKET THREAD (mm) (mm) (mm) (mm) (mm) RATING

DN 15 S1 1/2” BSP R01.151.015 27 38 15 21 18 15

DN 20 S1 3/4” BSP R01.151.020 34 42 17 27 20 15

DN 25 S1 1” BSP R01.151.025 43 49 19 34 24 15

DN 32 S1 1 1/4” BSP R01.151.032 52 56 22 42 27 15

DN 40 S1 1 1/2” BSP R01.151.040 59 58 22 48 27 15

DN 50 S1 2” BSP R01.151.050 74 70 26 60 33 15

DN 80 S1 3” BSP R01.151.080 107 95 31 89 46 12

DN 100 S1 4” BSP R01.151.100 129 110 39 114 55 12


48


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

FAUCET ADAPTOR (FEMALE ADAPTOR)

SIZE SIZE SIZE CODE A B C ID OD Z Z1 PN

SW SPIGOT THREAD SW SOCKET (mm) (mm) (mm) (mm) (mm) (mm) (mm) RATING

DN 15 S1 1/2” BSP - R01.153.015 32 42 18 - 21 22 - 15

DN 20 S1 3/4” BSP DN 15 S1 R01.153.020 38 47 21 21 27 25 27 15

DN 25 S1 1” BSP DN 20 S1 R01.153.025 47 53 24 27 34 28 31 15

DN 32 S1 1 1/4” BSP DN 25 S1 R01.153.032 57 63 28 34 42 34 38 15

DN 40 S1 1 1/2” BSP - R01.153.040 65 65 28 - 48 34 - 15

DN 50 S1 2” BSP DN 40 S1 R01.153.050 80 76 31 48 60 39 43 15


49



FABRICATED MOULDED

CAP

SIZE CODE ID A B C TYPE PN


DN 15 S1 R01.140.015 21 27 9 29 M 15

DN 20 S1 R01.140.020 27 33 11 33 M 15

DN 25 S1 R01.140.025 34 41 14 39 M 15

DN 32 S1 R01.140.032 42 52 17 46 M 15

DN 40 S1 R01.140.040 48 59 20 51 M 15

DN 50 S1 R01.140.050 60 74 24 61 M 15

DN 65 S1 R01.140.065 75 106 35 79 F* 12

DN 80 S1 R01.140.080 89 106 28 79 M 12

DN 100 S1 R01.140.100 114 132 33 95 M 12

DN 125 S1 R01.140.125 140 192 61 130 F* 12

DN 150 S1 R01.140.150 168 192 42 130 M 12

DN 200 S1 R11.140.225 225 262 30 150 F 9

DN 225 S1 R11.140.250 250 280 35 166 F 9

DN 300 S1 R11.140.315 315 355 35 199 F 9

* CAP DN65 IS MANUFACTURED FROM CAP DN80 AND DN80-DN65 REDUCING BUSH

* CAP DN125 IS MANUFACTURED FROM CAP DN150 AND DN150-DN125 REDUCING BUSH

50


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

THREADED PLUG

SIZE SIZE CODE A B C PN

THREAD (mm) (mm) (mm) RATING

DN 15 S1 1/2” BSP R01.155.015 27 21 15 15

DN 20 S1 3/4” BSP R01.155.020 33 23 16 15

DN 25 S1 1” BSP R01.155.025 41 26 19 15

DN 32 S1 1 1/4” BSP R01.155.032 51 30 22 15

DN 40 S1 1 1/2” BSP R01.155.040 58 31 22 15

DN 50 S1 2” BSP R01.155.050 71 36 26 15


51



SOCKET UNION

SIZE CODE A B ID Z PN


DN 15 S1 R01.205.015K 35 43 21 10 15

DN 20 S1 R01.205.020K 43 47 27 12 15

DN 25 S1 R01.205.025K 60 59 34 12 15

DN 32 S1 R01.205.032K 74 70 42 12 15

DN 40 S1 R01.205.040K 83 73 48 12 15

DN 50 S1 R01.205.050K 103 86 60 12 15

DN 65 S1 R01.205.065H - - - - -

DN 80 S1 R01.205.080K 158 114 89 12 15

DN 100 S1 R01.205.100K 182 142 114 14 15

SEALS’ MATERIAL - EPDM


52


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

SADDLE CLIP

SIZE CODE ID A B C D t

(mm) (mm) (mm) (mm) (mm) (mm)

DN 15 S1 R05.455.015 21 13 37 14 27 3

DN 20 S1 R05.455.020 27 18 41 14 34 3

DN 25 S1 R05.455.025 34 21 45 16 42 4

DN 32 S1 R05.455.032 42 29 65 16 54 4

DN 40 S1 R05.455.040 48 34 67 16 61 5

DN 50 S1 R05.455.050 60 38 87 22 73 5

DN 80 S1 R05.455.080 89 50 122 34 99 5

DN 100 S1 R05.455.100 114 65 156 38 127 5

C = CLIP THICKNESS

MATERIAL : BLACK POLYPROPYLENE

53



PIPE CLIP

SIZE CODE B C D d1 d2 d3 Z1 Z2 TYPE

(mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)

DN 15 S1 R05.434.015 25.5 10 6 21 10.5 5.5 16.5 19 B

DN 20 S1 R05.434.020 28.5 10 6 27 10.5 5.5 19 21.5 B

DN 25 S1 R05.434.025 32 10 6 34 10.5 5.5 24 26.5 B

DN 32 S1 R05.434.032 36 10 6.5 42 14 6.5 33.5 33.5 C

DN 40 S1 R05.434.040 39 10 6.5 48 14 6.5 37 37 C

DN 50 S1 R05.434.050 50 10 10 60 17 8.5 44.5 44.5 C

DN 80 S1 R05.434.080 105 - 15 89 - 9 89 71 C

DN 100 S1 R05.434.100 120 - 15 114 - 9 99 81 C

DN 150 S1 R05.434.150 147 - 20 169 - 11 136 111 G

MATERIAL: BLACK POLYPROPYLENE

54


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

RUBBER EXPANSION jOINT

SIZE CODE A C D E PN


DN 32 S1 R04.452.032 95 8 15° 4 15

DN 40 S1 R04.452.040 95 8 15° 4 15

DN 50 S1 R04.452.050 105 8 15° 5 15

DN 80 S1 R04.452.080 130 12 15° 6 15

DN 100 S1 R04.452.100 135 18 15° 10 15

DN 150 S1 R04.452.150 180 18 15° 10 15

DN 200 S1 R14.452.225 205 25 15° 14 15

DN 225 S1 R14.452.250 240 25 15° 14 15

DN 300 S1 R14.452.315 260 25 15° 14 15

DN 350 S1 R14.452.355 265 25 15° 14 9

DN 375 S1 R14.452.400 265 25 15° 14 9

DN 400 S1 R14.452.450 265 25 15° 14 9

DN 450 S1 R14.452.500 265 25 15° 14 9

DN 500 S1 R14.452.560 254 25 15° 16 9

DN 575 S1 R14.452.630 254 25 15° 16 6

DN 650 S1 R14.452.710 254 25 10° 16 6

* FLANGES SUPPLIED ARE ZINC PLATED. GALVANISED AVAILABLE ON REQUEST.

55



ANCHOR SLEEVE

SIZE CODE ID A B

(mm) (mm) (mm)

DN 50 S1 R01.272.050 60 74 40

DN 65 S1 R01.272.065 76 89 40

DN 80 S1 R01.272.080 89 104 50

DN 100 S1 R01.272.100 115 140 60

DN 125 S1 R01.272.125 141 168 75

DN 150 S1 R01.272.150 169 208 90

DN 200 S1 R11.272.225 227 250 120

DN 225 S1 R11.272.250 251 275 120

DN 300 S1 R11.272.315 316 344 120

DN 350 S1 R11.272.355 356 390 120

DN 375 S1 R11.272.400 401 450 120

DN 400 S1 R11.272.450 451 500 120

DN 450 S1 R11.272.500 502 550 180

DN 500 S1 R11.272.560 562 616 180

DN 575 S1 R11.272.630 632 710 180

DN 650 S1 R11.272.710 712 826 200

DN 750 S1 R11.272.826 828 922 200

56


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

ANCHOR FLANGE

SIZE CODE ID A B C D

(mm) (mm) (mm) (mm) (mm)

DN 50 S1 R01.137.050 61 96 40 14 74

DN 65 S1 R01.137.065 76 106 47 10 90

DN 80 S1 R01.137.080 90 127 57 18 118

DN 100 S1 R01.137.100 115 159 70 20 134

DN 125 S1 R01.137.125 141 187 84 14 165

DN 150 S1 R01.137.150 169 214 100 24 192

DN 200 S1 R11.137.225 226 271 144 35 247

DN 225 S1 R11.137.250 251 334 191 70 305

DN 300 S1 R11.137.315 317 376 224 70 362

DN 350 S1 R11.137.355 357 440 244 70 415

DN 375 S1 R11.137.400 402 488 306 110 450

DN 400 S1 R11.137.450 452 548 331 110 506

DN 450 S1 R11.137.500 502 613 356 110 561

DN 500 S1 R11.137.560 562 665 282 50 615

DN 575 S1 R11.137.630 632 708 340 65 669

DN 650 S1 R11.137.710 715 808 325 70 770

DN 750 S2 R11.137.826 804 922 430 110 870

57



BALL CHECK VALVE SINGLE UNION

SIZE CODE A B Z PN


DN 15 S1 R01.***.015K 48 95 62 15 DN 20 S1 R01.***.020K 59 112 73 15 DN 25 S1 R01.***.025K 69 124 79 15 DN 32 S1 R01.***.032K 96 148 94 15 DN 40 S1 R01.***.040K 96 148 88 15 DN 50 S1 R01.***.050K 103 177 105 15 DN 80 S1 R01.***.080K 178 215 114 9

CODE 836 - EPDM SEALS

CODE 838 - FPM SEALS

58


EURA

PIPE®

ABS P

IPE &

FITT

INGS P

RODU

CT CA

TALO

GUE

BALL VALVE DOUBLE UNION

SIZE CODE A B C D Z PN


DN 15 S1 R01.***.015K 51 101 48 81 67 15 DN 20 S1 R01.***.020K 63 119 65 87 79 15 DN 25 S1 R01.***.025K 73 134 69 101 86 15 DN 32 S1 R01.***.032K 105 161 88 127 101 15 DN 40 S1 R01.***.040K 105 160 88 127 98 15 DN 50 S1 R01.***.050K 135 191 108 151 118 15 DN 80 S1 R01.***.080K 182 260 138 191 158 15 DN 100 S1 R01.***.100K 217 314 165 241 187 15

CODE 880 - EPDM SEALS

CODE 882 - FPM SEALS

59



ABS SOLVENT CEMENT

CAN SIZE CODE

(litres)

0.25 R01.461.025A

1 R01.461.100A

4 R01.461.400A

SOLVENT CEMENT USAGE*

SIZE SOLVENT WELD

JOINTS PER LITRE**

DN 50 S1 135

DN 80 S1 45

DN 100 S1 35

DN 125 S1 20

DN 150 S1 20

DN 200 S1 10

DN 225 S1 4

DN 300 S1 4

DN 350 S1 3

DN 375 S1 2

DN 400 S1 1

DN 450 S1 1

DN 500 S1 0.5

DN 575 S1 0.5

DN 650 S1 0.3

DN 750 S1 0.3

* The usage of MEK is approximately 50% that of ABS cement

** A socket counts as 2 joints, a tee as 3 joints etc.

MEK CLEANER/PRIMER

CAN SIZE CODE

(litres)

0.25 R01.463.025A

1 R01.463.100A

4 R01.463.400A

PENTAIR WATER SOlUTIONSLEVEL 3, 9 GEORGE ST PARRAMATTA, NEW SOUTH WALES 2150 / WWW.PENTAIR.COM/WATERSOLUTIONS

All Pentair trademarks and logos are owned by Pentair Ltd. All other brand or product names are trademarks or registered marks of their respective owners. Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice. ABSPC1405 © 2014 Pentair Ltd. All Rights Reserved.

NEWcASTlE P: 02 4914 0700F: 02 4966 8776E: [email protected]

PERTH P: 08 9346 8500F: 08 9346 8501 E: [email protected]

SYdNEY P: 02 9794 3440F: 02 9794 3499E: [email protected]

TOWNSVIllE P: 07 4725 5940F: 07 4725 4995 E: [email protected]

AUcKlANd P: +64 9 921 7230F: +64 9 921 7231E: [email protected]

AdElAIdE P: 08 8340 3411F: 08 8340 3422E: [email protected]

BRISBANE P: 07 3266 2255 F: 07 3260 5221 E: [email protected]

dARWIN P: 08 8935 3300F: 08 8947 3981E: [email protected]

GOld cOAST P: 07 5589 4400F: 07 5534 7079E: [email protected]

mElBOURNE P: 03 9309 9133F: 03 9309 6237 E: [email protected]

HAmIlTON P: +64 7 958 7140F: +64 7 958 7141E: [email protected]

WEllINGTON P: +64 4 913 8514F: +64 4 913 8511E: [email protected]

cHRISTcHURcH P: +64 3 968 3260F: +64 3 968 3261E: [email protected]

eurapipe abs design manual

Documents