europower catalog
TRANSCRIPT
General InformationEuropower Hydraulics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3Conversion Chart (inches & mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Service Life Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Fluid Compatibility Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Hose Pressure Drop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Hose I.D. Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Minimum Bend Radius Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Hose Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10Instructions 1 - Piece Hose Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Instructions Non Skived Hose Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Instructions Skived Hose Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Instructions Reusable Non-skived Hose Assemblies . . . . . . . . . . . . . . . . . . . . .14How to measure assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15How to order Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Rubber HoseMedium Pressure 1 - Wire (C1T1SN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17High Pressure 2 - Wire (C2T2SN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18SAE 100 R16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19SAE 100 R17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20High Pressure Europulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Suction Hose SAE 100R4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Low Pressure SAE 100R6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23Euro - High - Temp (EHT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .241 & 2 Wire Eurowash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25Multi Spiral Hose (4SP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26Multi Spiral Hose (4SH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Multi Spiral Hose (R 12) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28Multi Spiral Hose (EH 920) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Thermoplastic HoseThermoplastic & PTFE Compatibility Chart . . . . . . . . . . . . . . . . . . . . . . . . .30-31702 Multipurpose 1-Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32711 Multipurpose 1-Wire Supertwin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33703 Multipurpose 2-Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34722 SAE 100 R7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35726 SAE 100 R7 Supertwin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36822 Orange Non-Conductive SAE 100 R7 . . . . . . . . . . . . . . . . . . . . . . . . . . . .37720 High Specification SAE 100 R7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38737 SAE 100 R8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39736 SAE 100 R8 Supertwin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40837 Non-Conductive SAE 100 R8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41714 1 - Wire Paint Spray Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42715 2 - Wire Paint Spray Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43709 2 - Wire Paint Spray ( For Aggressive Applications ) . . . . . . . . . . . . . . . . . .44754 Very High Pressure Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45755 Very High Pressure Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46352 Extra High Pressure Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47852 High Pressure Non-Conductive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .489038 Textile Braid Refrigeration Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .499081 Cold Temp. Forklift Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .509086 Air Cylinder Charging Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .519088 Pilot Line Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
PTFE HosePTFE Hose Factors of Suitability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53EFL1 Standard Wall PTFE Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54EFH1 Heavy Wall PTFE Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Table of Contents
BSP Hose EndsHow to Order One Piece Hose Ends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56FERRULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57-60BSP Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90BSP Male tapered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91BSP Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-92BSP Female 90° Swept Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93BSP Female 45° Swept Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94BSP Female 90° Compact Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95BSP O-ring Sealing Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95-96BSP O-ring Sealing Female 90° Swept Elbow . . . . . . . . . . . . . . . . . . . . . . .96-97BSP O-ring Sealing Female 45° Swept Elbow . . . . . . . . . . . . . . . . . . . . . . .97-98BSP O-ring Sealing 90° Compact Female . . . . . . . . . . . . . . . . . . . . . . . . . . . .98BSP O-ring Flat Face Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99BSP Banjo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100BSP Banjo Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
J.I.C. Hose EndsJ.I.C. Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61J.I.C. Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62-63J.I.C. Female 90° Swept Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64-65J.I.C. Female 45° Swept Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66J.I.C. 90° Compact Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67J.I.C. Female Equal Hexagon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Metric Hose EndsMetric Male – DKO ‘S’ & ‘L’ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79-80Metric Loose Nut Female DKO ‘S’ & ‘L’ . . . . . . . . . . . . . . . . . . . . . . . . . . . .81-82Metric Crimped Nut Female DKO ‘L’ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82Metric Loose Nut Female DKO ‘S’ & ‘L’ 90° Swept Elbow . . . . . . . . . . . . . .83-84Metric Crimped Nut Female DKO ‘L’ 90° Swept Elbow . . . . . . . . . . . . . . . . . . .84Metric Loose Nut Female DKO ‘S’ & ‘L’ 45° Swept Elbow . . . . . . . . . . . . . .85-86Metric Crimped Nut Female DKO ‘L’ 45° Swept Elbow . . . . . . . . . . . . . . . . . . .86Metric Standpipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87Metric Standpipe 90° Swept Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88Metric Standpipe 45° Swept Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
O.R.F.S. Hose EndsO.R.F.S. Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70O.R.F.S. Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70O.R.F.S. Female 90° Swept Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71O.R.F.S. Female 45° Swept Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72O.R.F.S. Female 90° Swept Elbow Long Drop . . . . . . . . . . . . . . . . . . . . . . . . . .72
S.A.E. Hose EndsS.A.E./I.S.O. Flange Straight Insert Code 61 . . . . . . . . . . . . . . . . . . . . . . . . . . .73S.A.E./I.S.O. Flange 90° Swept Elbow Code 61 . . . . . . . . . . . . . . . . . . . . . . . .74S.A.E./I.S.O. Flange 45° Swept Elbow Code 61 . . . . . . . . . . . . . . . . . . . . . . . .75S.A.E./I.S.O. Split Flange Clamps Code 61 . . . . . . . . . . . . . . . . . . . . . . . . . . . .75S.A.E./I.S.O. Flange Straight Insert Code 62 . . . . . . . . . . . . . . . . . . . . . . . . . . .76S.A.E./I.S.O. Flange 90° Swept Elbow Code 62 . . . . . . . . . . . . . . . . . . . . . . . .76S.A.E./I.S.O. Flange 45° Swept Elbow Code 62 . . . . . . . . . . . . . . . . . . . . . . . .77S.A.E./I.S.O. Split Flange Clamps Code 62 . . . . . . . . . . . . . . . . . . . . . . . . . . . .77S.A.E. “O” Ring Male/S.A.E. Swivel Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
N.P.T.F. Hose EndsN.P.T.F. Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68N.P.T.F. Swivel Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
N.P.S.M. Hose EndsN.P.S.M. Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Table of Contents
Misc. Inserts
N.P.T.F. Fixed Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101BSP 60° J.I.S. Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101-102Metric 60° Cone Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102Water Wash Inserts – Rubber Covered Nut . . . . . . . . . . . . . . . . . . . . . . . . . . .103Hose Joiners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103Interlock Ferrules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Interlock B.S.P. Hose EndsBSP Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104BSP Male Tapered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105BSP O-ring Sealing Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105BSP O-ring Sealing Female 90° Swept Elbow . . . . . . . . . . . . . . . . . . . . . . . .106BSP O-ring Sealing Female 45° Swept Elbow . . . . . . . . . . . . . . . . . . . . . . . .106
Interlock J.I.C. Hose EndsJ.I.C. Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107J.I.C. Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107J.I.C. Female 90° Swept Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108J.I.C. Female 45° Swept Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
Interlock S.A.E. FlangesS.A.E./I.S.O. Flange Straight Inserts Code 62 . . . . . . . . . . . . . . . . . . . . . . . . .109S.A.E./I.S.O. Flange 90° Swept Elbow Code 62 . . . . . . . . . . . . . . . . . . . . . . .109S.A.E./I.S.O. Flange 45° Swept Elbow Code 62 . . . . . . . . . . . . . . . . . . . . . . .110S.A.E./I.S.O. Split Flange Clamps Code 62 . . . . . . . . . . . . . . . . . . . . . . . . . . .110
Interlock Metric Hose EndsMetric Loose Nut Female DKO ‘S’ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111Metric Loose Nut Female DKO ‘S’ 90° Swept Elbow . . . . . . . . . . . . . . . . . . . .111Metric Loose Nut Female DKO ‘S’ 45° Swept Elbow . . . . . . . . . . . . . . . . . . . .112
Interlock N.P.T.F. Hose EndsN.P.T.F. Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112Very High Pressure Thermoplastic Ferrules . . . . . . . . . . . . . . . . . . . . . . .113-114
Very High Pressure Thermoplastic Hose EndsB.S.P. Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115B.S.P. Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115J.I.C. Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116Metric Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116Metric Loose Nut Female – DKO ‘S’ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116Metric Loose Nut Female – DKO ‘L’ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117N.P.T.F. Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117N.P.S.M. Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
Micro Hose & Pressure Test SystemsGeneral Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118Micro Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119Micro Hose Ends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120-121Pressure Gauge Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122Monitoring Plug Couplings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123Threaded Test-Point Couplings . . . . . . . . . . . . . . . . . . . . . . . . . . . .124-125-126Pressure Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127-128
Table of Contents
A PageA1. . . . . . . . . . . . . . . . . . . 90-104-115A2 . . . . . . . . . . . . . . . . . . . . . . 91-105A3. . . . . . . . . . . . . . . . . . . . 91-92-115A5 . . . . . . . . . . . . . . . . . . . . . . . . . . 93A7 . . . . . . . . . . . . . . . . . . . . . . . . . . 94A8 . . . . . . . . . . . . . . . . . . . . . . . . . . 95
B
B1. . . . . . . . . . . . . . . . . . . . 95-96-105B3. . . . . . . . . . . . . . . . . . . . 96-97-106B5. . . . . . . . . . . . . . . . . . . . 97-98-106B6. . . . . . . . . . . . . . . . . . . . . . . . . . 99B7. . . . . . . . . . . . . . . . . . 101-102-107B8 . . . . . . . . . . . . . . . . . . . . . . . . . 100B9. . . . . . . . . . . . . . . . . . . . . . . . . . 61
C
C1 . . . . . . . . . . . . . . . . 62-63-107-116C3. . . . . . . . . . . . . . . . . . . . 64-65-108C5 . . . . . . . . . . . . . . . . . . . . . . 66-108C6. . . . . . . . . . . . . . . . . . . . . . . . . . 67C7 . . . . . . . . . . . . . . . . . . . . . . . . . 101C9. . . . . . . . . . . . . . . . . . . . . . . . . . 78
D
D1. . . . . . . . . . . . . . . . . . . . . . . . . . 78D3. . . . . . . . . . . . . . . . . . . . . . . . . . 79D4. . . . . . . . . . . . . . . . . . . . . . . . . . 80
E
E8. . . . . . . . . . . . . . . . . . . 81-111-116E9 . . . . . . . . . . . . . . . . . . . . . . 82-117
FF1 . . . . . . . . . . . . . . . . . . . . . . . . . . 82F2 . . . . . . . . . . . . . . . . . . . . . . 83-111F4 . . . . . . . . . . . . . . . . . . . . . . . . . . 84F6 . . . . . . . . . . . . . . . . . . . . . . 85-112F7 . . . . . . . . . . . . . . . . . . . . . . . . . . 86F9 . . . . . . . . . . . . . . . . . . . . . . . . . 102
G
G4. . . . . . . . . . . . . . . . . . . . . . . . . . 87G6. . . . . . . . . . . . . . . . . . . . . . . . . . 88G7. . . . . . . . . . . . . . . . . . . . . . . . . . 89
H
H2. . . . . . . . . . . . . . . . . . . . . . . . . 101H3. . . . . . . . . . . . . . . . . . . 68-112-117H4. . . . . . . . . . . . . . . . . . . . . . . . . . 69H6. . . . . . . . . . . . . . . . . . . . . . . . . . 73H8. . . . . . . . . . . . . . . . . . . . . . . . . . 74H9. . . . . . . . . . . . . . . . . . . . . . . . . . 75
J
J5 . . . . . . . . . . . . . . . . . . . . . . . . . . 70J7 . . . . . . . . . . . . . . . . . . . . . . . . . . 70J9 . . . . . . . . . . . . . . . . . . . . . . . . . . 72
K
K2 . . . . . . . . . . . . . . . . . . . . . . . . . . 72K7 . . . . . . . . . . . . . . . . . . . . . . . . . . 98K8 . . . . . . . . . . . . . . . . . . . . . . . . . . 67K9 . . . . . . . . . . . . . . . . . . . . . . . . . . 70
L Page
L1 . . . . . . . . . . . . . . . . . . . . . . 76-109L2 . . . . . . . . . . . . . . . . . . . . . . 76-109L3 . . . . . . . . . . . . . . . . . . . . . . 77-110L4 . . . . . . . . . . . . . . . . . . . . . . . . . . 84L5 . . . . . . . . . . . . . . . . . . . . . . . . . . 86L6 . . . . . . . . . . . . . . . . . . . . . . . . . . 69L7 . . . . . . . . . . . . . . . . . . . . . . . . . 117L8 . . . . . . . . . . . . . . . . . . . . . . . . . 103L9 . . . . . . . . . . . . . . . . . . . . . . . . . 103
T
T2 . . . . . . . . . . . . . . . . . . . . . . . . . 116
HOSE TYPES RUBBER
J . . . . . . . . . . . . . . . . . . . . . . . . . . . 17G. . . . . . . . . . . . . . . . . . . . . . . . . . . 18R16 . . . . . . . . . . . . . . . . . . . . . . . . . 19R17 . . . . . . . . . . . . . . . . . . . . . . . . . 20EP . . . . . . . . . . . . . . . . . . . . . . . . . . 21R4. . . . . . . . . . . . . . . . . . . . . . . . . . 22R6. . . . . . . . . . . . . . . . . . . . . . . . . . 23EHT . . . . . . . . . . . . . . . . . . . . . . . . . 24PW1 . . . . . . . . . . . . . . . . . . . . . . . . 25PW2 . . . . . . . . . . . . . . . . . . . . . . . . 254SP . . . . . . . . . . . . . . . . . . . . . . . . . 264SH. . . . . . . . . . . . . . . . . . . . . . . . . 27R12 . . . . . . . . . . . . . . . . . . . . . . . . . 28920 . . . . . . . . . . . . . . . . . . . . . . . . . 29
THERMOPLASTIC711 . . . . . . . . . . . . . . . . . . . . . . . . . 30703 . . . . . . . . . . . . . . . . . . . . . . . . . 34726 . . . . . . . . . . . . . . . . . . . . . . . . . 36722 . . . . . . . . . . . . . . . . . . . . . . . . . 35702 . . . . . . . . . . . . . . . . . . . . . . . . . 32822 . . . . . . . . . . . . . . . . . . . . . . . . . 37720 . . . . . . . . . . . . . . . . . . . . . . . . . 38737 . . . . . . . . . . . . . . . . . . . . . . . . . 39736 . . . . . . . . . . . . . . . . . . . . . . . . . 40837 . . . . . . . . . . . . . . . . . . . . . . . . . 41714 . . . . . . . . . . . . . . . . . . . . . . . . . 42715 . . . . . . . . . . . . . . . . . . . . . . . . . 43709 . . . . . . . . . . . . . . . . . . . . . . . . . 44754 . . . . . . . . . . . . . . . . . . . . . . . . . 45755 . . . . . . . . . . . . . . . . . . . . . . . . . 46352 . . . . . . . . . . . . . . . . . . . . . . . . . 47852 . . . . . . . . . . . . . . . . . . . . . . . . . 489038 . . . . . . . . . . . . . . . . . . . . . . . . 499081 . . . . . . . . . . . . . . . . . . . . . . . . 509086 . . . . . . . . . . . . . . . . . . . . . . . . 519088 . . . . . . . . . . . . . . . . . . . . . . . . 52
PTFE HOSE
T . . . . . . . . . . . . . . . . . . . . . . . . . . . 54H. . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Assembly ComponentReference
FITTINGS
4
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
GENERAL HOSEINFORM
ATION
CONVERSION CHART
INCHES INCHES MM
1⁄64
1⁄32
3⁄64
1⁄16
5⁄64
3⁄32
7⁄64
1⁄89⁄64
5⁄32
11⁄64
3⁄16
13⁄64
7⁄32
15⁄64
1⁄417⁄64
9⁄32
19⁄64
5⁄16
21⁄64
11⁄32
23⁄64
3⁄825⁄64
13⁄32
27⁄64
7⁄16
29⁄64
15⁄32
31⁄64
1⁄233⁄64
17⁄32
35⁄64
9⁄16
37⁄64
19⁄32
39⁄64
5⁄841⁄64
0.016
0.031
0.047
0.063
0.078
0.094
0.109
0.125
0.141
0.156
0.172
0.188
0.203
0.219
0.234
0.250
0.266
0.281
0.297
0.313
0.328
0.344
0.359
0.375
0.391
0.406
0.422
0.438
0.453
0.469
0.484
0.500
0.516
0.531
0.547
0.563
0.578
0.594
0.609
0.625
0.641
0.397
0.794
1.191
1.588
1.984
2.381
2.778
3.175
3.572
3.969
4.366
4.763
5.159
5.556
5.953
6.350
6.747
7.144
7.541
7.938
8.334
8.731
9.128
9.525
9.992
10.319
10.716
11.113
11.509
11.906
12.303
12.700
13.097
13.494
13.891
14.288
14.684
15.081
15.478
15.875
16.272
Inches and millimeters conversion table
INCHES
21⁄32
43⁄64
11⁄16
45⁄64
23⁄32
47⁄64
3⁄449⁄64
25⁄32
51⁄64
13⁄16
53⁄64
27⁄32
55⁄64
7⁄857⁄64
29⁄32
59⁄64
15⁄16
61⁄64
31⁄32
63⁄64
1
1 1⁄41 1⁄21 3⁄4
2
2 1⁄23
3 1⁄24
4 1⁄25
6
7
8
9
10
11
INCHES
0.656
0.672
0.688
0.703
0.719
0.734
0.750
0.766
0.781
0.797
0.813
0.828
0.844
0.859
0.875
0.891
0.906
0.922
0.938
0.953
0.969
0.984
1.000
1.250
1.500
1.750
2.0
2.5
3.0
3.5
4.0
4.5
5.0
6.0
7.0
8.0
9.0
10.0
11.0
MM
16.669
17.066
17.463
17.859
18.256
18.653
19.050
19.447
19.844
20.241
20.638
21.034
21.431
21.828
22.225
22.622
23.019
23.416
23.813
24.209
24.606
25.003
25.400
31.750
38.100
44.450
50.8
63.5
76.2
88.9
101.6
114.3
127.0
152.4
177.8
203.2
228.6
254.0
279.4
6
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
FLUID COMPATIBILITY CHART OF HOSES
Fluids Hose TypeSAE 100 R1 PW1 EH910SAE 100 R2 PW2 EH920SAE 100 R3 R 9RSAE 100 R4 SAE 100 R6Euroflex HoseEH1505Euro Hi-temp
Acetic Acid (30%) ● ● ●
Acetone ✘ ✘ ✘
Acetylene ✔ ✔ ✔
Ammonia, gas
(150°C) ● ● ●
Ammonia, liquid ✔ ✔ ✔
Amyl Acetate ✘ ✘ ✘
Aniline ✘ ✘ ✘
Benzol ✘ ✘ ✘
Butane ● ● ●
Butyl Acetate ✘ ✘ ✘
Butyl Alcohol ✔ ✔ ✔
Carbon Dioxide ✔ ✔ ✔
Carbon Disulphide ✘ ✘ ✘
Carbonates ● ● ●
Chlorinated Solvents ✘ ✘ ✘
Chlorine ✘ ✘ ✘
Chloroform ✘ ✘ ✘
Compressed Air ✔ ✔ ✔
Cyclohexane ● ● ●
Ethers ● ✘ ●
Ethyl Acetate ✘ ✘ ✘
Ethyl Alcohol ✔ ✔ ✔
Ethyl Cellulose ✔ ✔ ✔
Ethyl Chloride ✘ ✘ ✘
Ethylene Glycol ✔ ✔ ✔
Fluorine ✘ ✘ ✘
Formaldehyde ✔ ✔ ✔
Freon 12 ✘ ✘ ✘
Fuel oil ✔ ● ✔
Gaseous Hydrogen ● ● ●
Gasoline ✔ ● ✔
Glycerine/Glycerol ✔ ✔ ✔
Hexane ✔ ✔ ✔
Hydraulic Oil ✔ ✘ ✔
Hydrochloric Acid ✘ ✔ ✘
Fluids Hose TypeSAE 100 R1 PW1 EH910SAE 100 R2 PW2 EH920SAE 100 R3 R 9RSAE 100 R4 SAE 100 R6Euroflex HoseEH1505Euro Hi-temp
Hydrogen Peroxide
(low volume) ✔ ✔ ✔
Hydrogen Peroxide
(high volume) ● ● ●
Isopropyl Alcohol ✔ ✔ ✔
Kerosene ✔ ✔ ✔
Liquid propane ● ● ●
Lubricant Oil ✔ ✔ ✔
Methyl Alcohol ✔ ✔ ✔
Methyl Chloride ✘ ✘ ✘
Methyl Ethyl Ketone ✘ ✘ ✘
Mineral greases ✔ ✔ ✔
Naphtha ✔ ✔ ✔
Natural Gas ✔ ✔ ✔
Nitric Acid (Dilute) ✘ ✘ ✘
Nitric Acid (Conc.) ✘ ✘ ✘
Oxalic Acid ✘ ✘ ✘
Oxygen ● ● ●
Perchlorethylene ✘ ✘ ✘
Phenol ✘ ✘ ✘
Phosphoric Acid
(Dilute) ✔ ✔ ✔
Phosphoric Acid
(Conc.) ✘ ✘ ✘
Phosphate ester
Base oil ✘ ✘ ✘
Satured Steam ✘ ● ✘
Sulphur Dioxide ✘ ✘ ✘
Sulphuric Acid
(Dilute) ✘ ✘ ✘
Toluene ✘ ✘ ✘
Trichlorethylene ✘ ✘ ✘
Vegetable greases ✔ ✔ ✔
Xylene ✘ ✘ ✘
✔ = Excellent ● = Limited resistance ✘ = Unsatisfactory
GENERAL HOSEINFORM
ATION
7
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
HOSE PRESSURE DROP
GENE
RAL
HOSE
INFO
RMAT
ION
8
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
GENERAL HOSEINFORM
ATION
HOSE I.D. SELECTION
NOTE:
Flow velocities in range A recommended forsuction and return lines.
Flow velocities in range B recommended fordelivery lines.
EXAMPLE:
To find the pipe bore size consistent with a flowrate of 4.2 gallons per minute and flow velocity12ft. per second, connect flow rate to flowvelocity and read bore on centre scale. Answer:0.415 inches
400
300
200
150
100
50
40
30
20
15
1098765
4
3
2.5.6.7.8.91
1.5
2
3
4
5
10
15
20
30
40
50
100 25 10
20
15
10
5
4
3
2
5
4
3
2
1.5
1
.5
.4
.3
.2
.15
.1
1.5
1
.5
.4
.3
.25
1.3
.4
.5
.6
.7
.8
.91
1.5
2
3
4
56789
10
1.5
2
3
4
5678910
15
20
30
40
50
FLO
W -
GA
LLO
NS/
MIN
FLO
W -
LITR
ES/
MIN
BO
RE
- CE
NTI
ME
TER
S
BO
RE
- IN
CHES
FLOW
VE
LOCI
TY
FT./S
EC
MET
RE -
SEC
B
A
9
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
GENE
RAL
HOSE
INFO
RMAT
ION
In the majority of installations a hose assembly is required to have at least one bend in its length. It is essentialtherefore that to obtain the maximum expected life from the assembly undue tension at the end-fittings due tobending must be avoided.
The following information is intended to provide plant designers with a guide to ensure that the correct hoselength is calculated.
MINIMUM BEND RADIUS ILLUSTRATIONS
A A
R
X
A A
R
X
R
T
T12T1
2" "
Length = 2A + 3.142R Length = 2A + X
To avoid tension on the end fitting a short lengthof straight hose is allowed at each end of the unitso that the bend starts away from the coupling.
A compensating distance calculated to cover thelength of a standard end fitting plus the allowablestraight length of hose, is shown for each size as“A” in the table.
Thus in the example shown above the length ofthe unit will be L = 2A + 3.142R. (Where R shouldnot be less than the minimum bend radius for therespective size of hose).
For all other types of bends the general formula L= 2A + X covers any installation. (Where X is theintermediate length of hose which may be suitablycalculated or measured).
Static Hose Installations
N.B. “A” Dimensions do not include lengths of special fittings, adaptors, etc. If these items are included on anassembly extra length must be allowed accordingly.
Hose Bores
Dim ‘A’
3⁄16"
31⁄2"
1⁄4"
4"
5⁄16"
41⁄4"
3⁄8"
41⁄2"
5⁄8"
51⁄2"
3⁄4"
6"
1⁄2"
5"
1"
63⁄4"
11⁄4"
73⁄4"
11⁄2"
83⁄4"
2"
10"
Static Hose Installations
Length = 2A + X + T
Due consideration must be given to the type ofinstallation having a relative movement betweenend-fittings.
Obviously it is necessary to allow an extra portionof “straight hose” to relieve tension at thecoupling when the hose is being flexed. (seeTable).
Thus if the amount of travel is “T” then the extraamount of straight hose allowed at each end-fitting must be
1⁄2 T (see above).
The general formula then becomes L = 2A + X +T. This additional length will then permitreasonable flexing in all positions of travel.
N.B. To operate below the recommended minbend radius will dramatically reduce the statedworking pressure of the hose.
Operational Flexing
10
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
GENERAL HOSEINFORM
ATION
InstallationHydraulic hose may change in length from +2% to -4% when pressurised. Allowance should be made to provide sufficient slack to compensate for any changes in length. Keep the bend radius to the largest possiblediameter, this will prevent collapse of line or flow restriction. When installing hydraulic hose, use the layline as a guide to prevent twisting. Eliminate contact between moving parts and hose. If the application cannot avoidcontact, a spring guard should be used. Europower recommends a fire sleeve to be applied on the outsidecover when hydraulic hose lines are used near the exhaust manifold or any other source of heat.
Provide slack or bend in the hose line to provide for changes in length that may occur when pressure is applied.
HOSE SELECTION
Right Wrong
Observe linear stripe. The hose must not be twisted. High pressures applied to a twisted hose may cause failureor loosen the nut.
Right Wrong
Relieve sharp bends, avoid strain or hose collapse and make cleaner installations by using elbows or other adaptor fittings. Provide as large a bend radius as possible. Never use less than the recommended minimumbend radius specified for the hose.
Wrong Wrong
Provide additional bend radius when lines are subject to flexing and remember that the metal end fittings arenot flexible. Place line support clamps so as not to restrict hose flexing.
Right
Wrong
11
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
GENE
RAL
HOSE
INFO
RMAT
ION
Mark dimension ‘B’ on hose. Lightlylubricate the insert with fluid whichis to be used in the hose or acompatible lubricant. Push thefitting onto the hose until it coversthe work or until hose meets theferrule bottom.
Step 2
Place the assembly into theswaging machine and swage downas required. See the appropriatepage of the swaging manual.
Step 3
Insert bore collapse should be checked with Europower Hydraulics collapse mandrels or appropriate measuringinstruments where necessary.
Cut the hose squarely to the desired length using a finetoothed hacksaw or preferably a cutoff machine, notforgetting to subtract the hose cut-off length ‘A’ (seebelow step 2). Remove dirt particles from the bore of thehose. Before pushing the coupling onto the hose, it isimportant to clearly mark a line on the hose outer surface(length ‘B’) to indicate when the coupling is fully pushedhome.
MANUFACTURING INSTRUCTIONS FOR EUROPOWER SWAGED 1-Piece HOSE ASSEMBLIES
Step 1
12
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
GENERAL HOSEINFORM
ATION
Push the ferrule onto the hose untilit bottoms. Lightly lubricate theinsert with the fluid which is to beused in the hose or a compatiblelubricant and push into the hoseuntil the stop ‘B’ meets the hoseend. When using XTC/XTR ferrulesthe insert does not meet the hoseend.
Step 2
A
B
Check that the ferrule is correctlylocated over the insert. Place theassembly into the swaging machineand swage down as required. Seethe appropriate page of theswaging manual.
Step 3
By Micrometer or vernier
Insert bore collapse should be checked with Europower Hydraulics collapse mandrels or appropriate measuringinstruments where necessary.
Cut the hose squarely to the desired length using afine toothed hacksaw or preferably a cutoff machine,not forgetting to subtract the hose cut-off length ‘A’(see below step 2). Remove dirt particles from thebore of the hose. Before pushing the coupling ontothe hose, it is important to clearly mark a line on thehose outer surface (length ‘B’) to indicate when thecoupling is fully pushed home.
MANUFACTURING INSTRUCTIONS FOR EUROPOWER SWAGED NON-SKIVED HOSE ASSEMBLIES
Step 1
13
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
GENE
RAL
HOSE
INFO
RMAT
ION
Cut the hose squarely to the desired length using afine toothed hacksaw or preferably a cutoff machine,not forgetting to subtract the hose cut-off length ‘A’(see below step 3). Remove dirt particles from thebore of the hose.
MANUFACTURING INSTRUCTIONS FOR EUROPOWER SWAGED SKIVED HOSE ASSEMBLIES
Step 1
Skive down the outer cover of the hose to thesteel reinforcement over length ‘L’. See theappropriate page in the swaging manual forstripping length. Before pushing the coupling ontothe hose, it is important to clearly mark a line onthe hose outer surface (length ‘B’) to indicatewhen the coupling is fully pushed home.
Step 2
L
Push the ferrule onto the hoseuntil it bottoms. Lightly lubricatethe insert with the fluid which is tobe used in the hose or acompatible lubricant and push intothe hose until the stop ‘B’ meetsthe hose end.
Step 3
A
B
Check that the ferrule is correctlylocated over the insert. Place theassembly into the swaging machineand swage down as required. Seethe appropriate page of theswaging manual.
Step 4
By Micrometer or vernier
Insert bore collapse should be checked with Europower Hydraulics collapse mandrels or appropriate measuring instru-ments where necessary.
14
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
GENERAL HOSE
INFORM
ATION
Cut the hose squarely to the desired length using a fine toothed hacksaw or preferably a cutoff machine, not forgetting to subtract the hose cut-off length ‘A’ (obtained from the insertdimensions in the Europower fittings catalogue). Remove dirt particles from the bore of thehose. It is important to ensure that the outer cover of the hose end and ferrule bore remain oil free.
Step 1
Step 1Mandrelin vice
First notch
Cut here
Slit the cover to be removed longitudinally around the diameter of the hose, then slice theunwanted cover cleanly off the wire braiding. Do not use a hacksaw for this operation.
Step 2
Finish cleaning up with a wire brush to remove any remaining pieces of hose cover from thewire braiding. It is important that steps are taken to ensure that the wire braiding remains oilfree.
Step 3
Place the ferrule in the vice using soft jaws. Do not lubricate either the braiding or theinternal threads of the ferrule. Screw the hose into the ferrule (anticlockwise) until the hosebottoms.
Step 4
Lubricate the hose insert ( the taper area only not the threads) with the fluid which is to beused in the hose or a compatible lubricant.
Step 5
Step 6
NOTE: If a wire brushing machine is available cut the hose as Step 1 then proceed as follows. Set machine to take the correctdiameter hose and the correct length of cover to be removed, brush down the outer cover of the hose to the steel reinforcementthen proceed with steps 4 to 6 inclusive.
Place the ferrule in the vice using soft jaws. Screw the hose anticlockwise into the ferrule untilthe hose bottoms.
Step 2
Lubricate the insert (the taper area only not the threads) with the fluid which is to be used inthe hose or a compatible lubricant.
Step 3
Screw the insert into the ferrule until the hexagon just contacts the ferrule.* Angular alignment between 2 elbow inserts can be achieved by “backing off” 1 insert by upto 1 revolution
Step 4
MANUFACTURING INSTRUCTIONS FOR EUROPOWER REUSABLE NON-SKIVED HOSE ASSEMBLIES
MANUFACTURING INSTRUCTIONS FOR EUROPOWER REUSABLE SKIVED HOSE ASSEMBLIES
Cut the hose squarely to the desired length using a fine toothed hacksaw or preferably a cutoffmachine, not forgetting to subtract the hose cut-off length ‘A’ (obtained from the insertdimensions in the Europower fittings catalogue). Remove dirt particles from the bore of thehose. Place the appropriate mandrel in the vice and push the hose end on to the mandrel.Mark on the hose end a length equivalent to the distance of the first notch from the hose leadin end of the ferrule then cut squarely down to the wire braiding around the full circumference.Do not use a hacksaw for this operation.
Screw the insert into the ferrule until the hexagon just contacts the ferrule.* Angular alignment between 2 elbow inserts can be achieved by “backing off” 1 insert by upto 1 revolution
15
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
GEN
ERAL
HOS
E IN
FORM
ATIO
N
HOW TO MEASURE EUROPOWER ASSEMBLIES
Length over nipples
Swivel female and male union
Length between centre lines offemale nipple and banjo
Banjo couplingSwivel female 90˚swept union
225˚
Length between centre line of S.P.and end of nipple
Swivel female union45˚ standpipe
Length between S.P. and nipple ends
Male unionStraight standpipe
Length between male nipple andcentre of female nipple
Swivel female 45˚ swept union
Male union
Length between nipple end andcentre line of flange head
90˚ SAE flangeMale union
Assembly length 0 to 305mm ± 3mm305mm to 457mm ± 4mm457mm to 914mm ± 6mm914mm upwards ± 1%
Elbow angular relationship ± 3°See below
Standard Tolerances
Hold the assembly so that you can look along the length of the hose with the fitting furthest away from you in thevertical position (nipple upwards). Measure the angle between the vertical fitting and the one nearest to you in aclockwise direction.Relationships can then be expressed from 0° to 360°.
If angle not given elbows are positioned at 0°.
Angular Relationships
16
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
GENERAL HOSEINFORM
ATION
How to order Factory Assembled Hoses
Order Number 6 G A106 H306 24
HOSE SIZE (-)
HOSE TYPE
END FITTING
END FITTING
OVERALL LENGTH (Inches)
SAE BSP Thread Japanese JapaneseSAE 37• O-ring SAE 45° NPTF Pipe Tapered & BSP Metric French
Size Flare Straight Flare Thread Parallel 30° 30° GAZ
-2 5/16–24 5/16–24 5/16–24 1/8–27 1/8–28 M14 x 1.5 M20 x 1.5-3 3/8–24 3/8–24 3/8–24 M16 x 1.5 M24 x 1.5-4 7/16–20 7/16–20 7/16–20 1/4–18 1/4–19 1/4–19 M18 x 1.5 M30 x 1.5-5 1/2–20 1/2–20 1/2–20 M14 x 1.5 M36 x 1.5-6 9/16–18 9/16–18 5/8–18 3/8–18 3/8–19 3/8–19 M22 x 1.5 M45 x 1.5-8 3/4–16 3/4–16 3/4–16 1/2–14 1/2–14 1/2–14 M24 x 1.5
-10 7/8–14 7/8–14 7/8–14 5/8–14 M28 x 1.5 -12 1-1/16–12 1-1/16–12 1-1/16–14 3/4–14 3/4–14 3/4–14 M33 x 2 -14 1-3/16–12 1-3/16–12 M36 x 2 -16 1-5/16–12 1-5/16–12 1–11-1/2 1–11 1–11 M42 x 2 -20 1-5/8–12 1-5/8–12 1-1/4–11-1/2 1-1/4–11-24 1-7/8–12 1-7/8–12 1-1/2–11-1/2 1-1/2–11 -32 2-1/2–12 2-1/2–12 2–11-1/2 2–11
Nut Size Thread Nut Size Thread
4LL M8 x 1.0 6S M14 x 1.5 6LL M10 x 1.0 8S M16 x 1.5 8LL M12 x 1.0 10S M18 x 1.5
12S M20 x 1.5 6L M12 x 1.5 14S M22 x 1.5 8L M14 x 1.5 16S M24 x 1.5
10L M16 x 1.5 20S M30 x 2 12L M18 x 1.5 25S M36 x 2 15L M22 x 1.5 30S M42 x 218L M26 x 1.5 38S M52 x 2 22L M30 x 2 28L M36 x 2 35L M45 x 2 42L M52 x 2
DIN 3870 Nut Threads
Hose Fitting Thread Types and Sizes
Note: Dimension A in hose fitting charts represents cut-off lengths for assemblies
17
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
RUBB
ER H
OSE
JHoseType
C1T1SN-04 1/4 6.4 0.555 14.1 3263 225 13050 900 4.0 100 0.168 0.25
C1T1SN-05 5/16 7.9 0.618 15.7 3118 215 12325 850 4.5 115 0.208 0.31
C1T1SN-06 3/8 9.5 0.713 18.1 2610 180 10440 720 5.0 130 0.242 0.36
C1T1SN-08 1/2 12.7 0.843 21.4 2320 160 9280 640 7.0 180 0.302 0.45
C1T1SN-10 5/8 15.9 1.000 24.5 1885 130 7540 520 8.0 200 0.349 0.52
C1T1SN-12 3/4 19.1 1.122 28.5 1523 105 6090 420 9.5 240 0.437 0.65
C1T1SN-16 1 25.4 1.441 36.6 1276 88 5075 350 12.0 300 0.612 0.91
C1T1SN-20 1 1/4 31.8 1.764 44.8 914 63 3625 250 16.5 420 0.874 1.30
ConstructionLiner: Synthetic Nitrile rubberReinforcement: Single high tensile steel wire braidCover: Styrene Butadiene Rubber (SBR)
ApplicationMedium pressure hydraulic oil lines.Suitable for carrying fuels, naphtha, gasoline and lubricants.
Temperature Range–40°F to +210°F (–40°C to +100°C) with peaks up to +250°F (120°C), depending on the medium.Meets or exceeds requirements of DIN EN 853 1SN, (formerly DIN 20022 1SN).
FittingsEuropower ‘U’ series: 2-piece permanently swaged fittings
‘A’ series 1-piece permanently swaged fittings
DIMENSIONS:
Dual branded: SAE 100 R1AT/DIN EN 853 1SN
Hose TypeNOMINAL I.D. O.D.
MAX WORKINGPRESSURE
MINIMUMBURST
MINIMUM BEND RADIUS
WEIGHT
INCHES MM IN MAX-MM PSI BAR PSI BAR INCHES MM LB/FT KG/M
C1T1SN-03 3/16 4.8 0.492 12.5 3625 250 14500 1000 3.5 90 0.134 0.20
C1T1SN-24 1 1/2 38.1 2.051 52.1 725 50 2900 200 20.0 500 1.142 1.70
C1T1SN-32 2 50.8 2.579 65.5 580 40 2320 160 25.0 630 1.680 2.50
FERRULE PART NO.
NON SKIVE EXTERNAL SKIVE
U5000-03
U5000-04
U5000-05
U5000-06
U5000-08
U5000-10
U5000-12
U5000-16
U5000-20
U5000-24
U5000-32
U1000-04
U1000-05
U1000-06
U1000-08
U1000-10
U1000-12
U1000-16
U1000-20
U1000-24
U1000-32
U1000-03
MEDIUM PRESSURE HOSE
18
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
GHoseType
RUBBER HOSE
HIGH PRESSURE HOSE
ConstructionLiner: Synthetic Nitrile rubberReinforcement: 2 braids of high tensile steel wireCover: Styrene Butadiene Rubber (SBR)
ApplicationHigh pressure hydraulic oil lines.Suitable for carrying fuels, naphtha, gasoline and lubricants.
Temperature Range–40°F to +210°F (–40°C to +100°C) with peaks up to +250°F (120°C), depending on the medium.Meets or exceeds requirements of DIN EN 853 2SN, (formerly DIN 20022 2SN).
FittingsEuropower ‘U’ series: 2-piece fittings
‘A’ series 1-piece fittings
DIMENSIONS:
Dual branded: SAE 100 R2AT/DIN EN 853 2SN
HOSE TYPENOMINAL I.D. O.D.
MAX WORKINGPRESSURE
MINIMUMBURST
MINIMUM BEND RADIUS
WEIGHT
INCHES MM IN MAX-MM PSI BAR PSI BAR INCHES MM LB/FT KG/M
C2T2SN-03 3/16 4.8 0.555 14.1 6018 415 23925 1650 3.5 90 0.215 0.32
C2T2SN-04 1/4 6.4 0.618 15.7 5800 400 23200 1600 4.0 100 0.242 0.36
C2T2SN-05 5/16 7.9 0.681 17.3 5075 350 20300 1400 4.5 115 0.302 0.45
C2T2SN-06 3/8 9.5 0.776 19.7 4785 330 19140 1320 5.0 130 0.363 0.54
C2T2SN-08 1/2 12.7 0.906 23.0 3988 275 15950 1100 7.0 180 0.457 0.68
C2T2SN-10 5/8 15.9 1.031 26.2 3625 250 14500 1000 8.0 200 0.538 0.80
C2T2SN-12 3/4 19.1 1.185 30.1 3118 215 12325 850 9.5 240 0.632 0.94
C2T2SN-16 1 25.4 1.531 38.9 2393 165 9425 650 12.0 300 0.907 1.35
C2T2SN-20 1 1/4 31.8 1.949 49.5 1813 125 7250 500 16.5 420 1.445 2.15
C2T2SN-24 1 1/2 38.1 2.201 55.9 1305 90 5220 360 20.0 500 1.781 2.65
C2T2SN-32 2 50.8 2.701 68.6 1160 80 4640 320 25.0 630 2.300 3.42
FERRULE PART NO.
NON SKIVE EXTERNAL SKIVE
U5000-03
U5000-04
U5000-05
U5000-06
U5000-08
U5000-10
U5000-12
U5000-16
U5000-20
U5000-24
U5000-32
U2000-04
U2000-05
U2000-06
U2000-08
U2000-10
U2000-12
U2000-16
U2000-20
U2000-24
U2000-32
U2000-03
19
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
R16HoseType
RUBB
ER H
OSE
HYDRAULIC HOSEMeets or exceeds requirements of SAE 100 R16
ConstructionLiner: Oil resistant synthetic rubberReinforcement: 2 braids of high tensile steel wireCover: Abrasion and weather resistant synthetic rubber, MSHA Approved
ApplicationPulsating pressure hydraulic applications.
Temperature Range–40°F to +210°F (–40°C to +100°C)
FittingsEuropower ‘U’ series: 2-piece permanently swaged fittings
‘A’ series 1-piece permanently swaged fittings
DIMENSIONS:
HOSE TYPENOMINAL I.D. O.D.
MAX WORKINGPRESSURE
MINIMUMBURST
MINIMUM BEND RADIUS
WEIGHT
INCHES MM IN MAX-MM PSI BAR PSI BAR INCHES MM LB/FT KG/M
R16-04 1/4 6.4 0.567 14.4 5000 345 20000 1379 2.0 50 0.175 0.26
R16-05 5/16 7.9 0.618 15.7 4250 293 17000 1172 2.0 57 0.208 0.31
R16-06 3/8 9.5 0.740 18.8 4000 276 16000 1103 2.5 63 0.267 0.40
R16-08 1/2 12.7 0.862 21.9 3500 241 14000 965 3.5 88 0.323 0.48
R16-10 5/8 15.9 1.000 25.4 2750 190 11000 758 4.0 100 0.370 0.55
R16-12 3/4 19.0 1.138 28.9 2250 155 9000 620 4.5 120 0.477 0.71
R16-16 1 25.4 1.437 36.5 2000 138 8000 552 6.0 150 0.672 1.00
FERRULE PART NO.
NON SKIVE EXTERNAL SKIVE
U5000-04
U5000-05
U5000-06
U5000-08
U5000-10
U5000-12
U5000-16
N/A
N/A
N/A
N/A
N/A
N/A
N/A
FERRULE PART NO.
NON SKIVE EXTERNAL SKIVE
20
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
R17HoseType
RUBBER HOSE
HYDRAULIC HOSEMeets or exceeds requirements of SAE 100 R17
ConstructionLiner: Oil resistant synthetic rubberReinforcement: 2 braids of high tensile steel wire 1/4” - 1/2”, 2 braids 5/8” - 1”Cover: Abrasion and weather resistant synthetic rubber
ApplicationPulsating pressure hydraulic applications.
Temperature Range–40°F to +210°F (–40°C to +100°C)
FittingsEuropower ‘U’ series: 2-piece permanently swaged fittings
‘A’ series 1-piece permanently swaged fittings
DIMENSIONS:
HOSE TYPENOMINAL I.D. O.D.
MAX WORKINGPRESSURE
MINIMUMBURST
MINIMUM BEND RADIUS
WEIGHT
INCHES MM IN MAX-MM PSI BAR PSI BAR INCHES MM LB/FT KG/M
R17-04 1/4 6.4 0.492 12.5 3000 210 12000 840 2.0 50 0.128 0.19
R17-05 5/16 7.9 0.563 14.3 3000 210 12000 840 2.0 55 0.148 0.22
R17-06 3/8 9.5 0.650 16.5 3000 210 12000 840 2.5 65 0.181 0.27
R17-08 1/2 12.7 0.776 19.7 3000 210 12000 840 3.5 90 0.309 0.46
R17-10 5/8 15.9 0.945 24.0 3000 210 12000 840 4.0 105 0.383 0.57
R17-12 3/4 19.0 1.012 25.7 3000 210 12000 840 5.0 125 0.524 0.78
R17-16 1 25.4 1.425 36.2 3000 210 12000 840 6.0 150 0.941 1.40
U5000-04
U5000-05
U5000-06
U5000-08
U5000-10
U5000-12
U5000-16
N/A
N/A
N/A
N/A
N/A
N/A
N/A
21
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
EPHoseType
RUBB
ER H
OSE
DIMENSIONS:
HIGH PRESSURE HOSEEUROPULSE 2-wire compact hose to 1-wire dimensions exceeds DIN EN853 2SN
ConstructionLiner: Oil resistant seamless black synthetic rubberReinforcement: 2 braids of high tensile steel wireCover: Styrene Butadiene Rubber (SBR)
ApplicationHigh pressure oil lines.Suitable for carrying fuels, naphtha, gasoline and lubricants.
Temperature Range–40°F to +210°F (–40°C to +100°C) with peaks up to +250°F (120°C).Compact hose which exceeds flexibility and pressure requirements of DIN EN853 2SN.
FittingsEuropower ‘U’ series: 2-piece fittings, with either skived or non-skived ferrules.
‘A’ series: 1-piece permanently swaged fittings.
Note Europulse type hose meets Europower ‘DMQ’ approved specifications when impulse tested at 133% of the stateddynamic working pressure (125% for dash 16) using approved Europower permanently swaged fittings.
HOSE TYPENOMINAL I.D. O.D.
MAX WORKINGPRESSURE
MINIMUMBURST
MINIMUM BEND RADIUS
WEIGHT
INCHES MM IN MAX-MM PSI BAR PSI BAR INCHES MM LB/FT KG/M
EUROPULSE-04 1/4 6.5 0.559 14.2 5800 400 23200 1600 3 75 0.249 0.37
EUROPULSE-06 3/8 9.5 0.720 18.3 5075 350 20300 1400 3.5 90 0.289 0.43
EUROPULSE-08 1/2 13.0 0.846 21.5 4350 300 17400 1200 5.1 130 0.349 0.52
EUROPULSE-10 5/8 16.0 0.972 24.7 4000 275 16000 1100 6.7 170 0.423 0.63
EUROPULSE-12 3/4 19.0 1.126 28.6 3400 235 13600 950 7.9 200 0.497 0.74
EUROPULSE-16 1 25 1.441 36.6 2675 185 10700 740 9.8 250 0.739 1.10
FERRULE PART NO.
NON SKIVE EXTERNAL SKIVE
U1000-04
U1000-06
U1000-08
U1000-10
U1000-12
U1000-16
U5000-04
U5000-06
U5000-08
U5000-10
U5000-12
U5000-16
22
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
RUBBER HOSE
FERRULE PART NO.
EXTERNAL SKIVE
R4HoseType
RETURN AND SUCTION HOSESAE 100 R4
DIMENSIONS:
ConstructionLiner: Oil resistant synthetic rubberReinforcement: Open wire pitched on 1 braid of textileCover: Oil and weather resistant synthetic rubber
ApplicationPetroleum and water-based hydraulic fluids in suction lines and low pressure return lines.
Temperature Range–40°F to +210°F (–40°C to +100°C) with peaks up to +250°F (120°C).Meets or exceeds requirements of S.A.E. 100 R4.
FittingsEuropower ‘U’ series: 2-piece fittings
HOSE TYPENOMINAL I.D. O.D.
MAX WORKINGPRESSURE
MINIMUMBURST
MINIMUM BEND RADIUS
WEIGHT
INCHES MM IN MAX-MM PSI BAR PSI BAR INCHES MM LB/FT KG/M
R4-12 3/4 19.1 1.374 34.9 300 21 1200 83 5.0 127 0.544 0.81
R4-16 1 25.4 1.626 41.3 250 17 1000 69 6.0 152 0.726 1.08
R4-20 1 1/4 31.8 2.000 50.8 200 14 800 55 8.0 203 0.827 1.23
R4-24 1 1/2 38.1 2.252 57.2 150 10 600 41 10.0 254 1.028 1.53
R4-32 2 50.8 2.752 69.9 100 7 400 28 12.0 305 1.364 2.03
R4-40 2 1/2 63.5 3.252 82.6 62 4 250 17 14.0 355 1.606 2.39
R4-48 3 76.2 3.752 95.3 56 3 225 15 18.0 457 2.097 3.12
NON SKIVE
U5000-12 N/A
N/A
N/A
N/A
N/A
N/A
N/A
–
U5000-20
U5000-24
U5000-32
–
–
23
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
RUBB
ER H
OSE
FERRULE PART NO.
EXTERNAL SKIVENON SKIVE
R6HoseType
LOW PRESSURE HOSESAE 100 R6
ConstructionLiner: Oil resistant synthetic rubberReinforcement: 1 braid of textileCover: Oil and weather resistant synthetic rubber
ApplicationFor low pressure, hydraulic and pneumatic service.Suitable for carrying air, fuels, gasoline and lubricants.
Temperature Range–40°F to +210°F (–40°C to +100°C) with peaks up to +250°F (120°C).Meets or exceeds requirements of S.A.E. 100 R6.
FittingsEuropower ‘U’ series: 2-piece fittings
DIMENSIONS:
HOSE TYPENOMINAL I.D. O.D.
MAX WORKINGPRESSURE
MINIMUMBURST
MINIMUM BEND RADIUS
WEIGHT
INCHES MM IN MAX-MM PSI BAR PSI BAR INCHES MM LB/FT KG/M
U8000-04
U7000-05
U7000-06
U5000-08
U5000-10
U5000-12
N/A
N/A
N/A
N/A
N/A
N/A
R6-04 1/4 6.4 0.531 13.5 400 28 1600 112 2.5 65 0.087 0.13
R6-05 5/16 7.9 0.594 15.1 400 28 1600 112 3.0 75 0.101 0.15
R6-06 3/8 9.5 0.657 16.7 400 28 1600 112 3.0 75 0.121 0.18
R6-08 1/2 12.7 0.811 20.6 400 28 1600 112 4.0 100 0.175 0.26
R6-10 5/8 15.9 0.937 23.8 350 25 1400 100 5.0 125 0.208 0.31
R6-12 3/4 19.0 1.000 25.4 300 21 1200 83 6.0 152 0.242 0.36
FERRULE PART NO.
EXTERNAL SKIVENON SKIVE
EHTHoseType
DIMENSIONS:
HIGH TEMPERATURE HOSE (EURO HI-TEMP)EURO HI-TEMP
ConstructionLiner: Synthetic oil and heat resistant rubberReinforcement: Single high tensile steel wire braidCover: Hypalon
ApplicationMedium pressure; high temperature hydraulic oil lines, truck engine, oil and fuel services.This hose has been specifically designed for high temperature compressor applications.For details please contact Europower Hydraulics Ltd., Technical Department.(Please specify pinpricked for compressor applications — i.e. EHT – [dash size] – EPP.)
Temperature Range–40°F to +300°F (–40°C to +150°C).
FittingsEuropower ‘U’ series: 2-piece fittings
HOSE TYPENOMINAL I.D. O.D.
MAX WORKINGPRESSURE
MINIMUMBURST
MINIMUM BEND RADIUS
WEIGHT
INCHES MM IN MAX-MM PSI BAR PSI BAR INCHES MM LB/FT KG/M
EHT-04 1/4 6.4 0.555 14.1 2750 190 11000 760 3.5 95 0.168 0.25
EHT-06 3/8 9.5 0.713 18.1 2250 155 9000 620 4.5 110 0.242 0.36
EHT-08 1/2 12.7 0.846 21.5 2000 140 8000 560 6.5 160 0.302 0.45
EHT-10 5/8 15.9 0.972 24.7 1500 105 6000 420 7.0 180 0.349 0.52
EHT-12 3/4 19.1 1.126 28.6 1250 85 5000 340 8.5 220 0.437 0.65
EHT-16 1 25.4 1.441 36.6 1000 70 4000 280 11.0 275 0.612 0.91
EHT-20 1 1/4 31.8 1.764 44.8 625 45 2500 180 15.5 395 0.874 1.30
EHT-24 1 1/2 38.1 2.047 52.0 500 35 2000 140 19.0 485 1.142 1.70
U5000-04
U5000-06
U5000-08
U5000-10
U5000-12
U5000-16
U5000-20
U5000-24
U1000-04
U1000-06
U1000-08
U1000-10
U1000-12
U1000-16
U1000-20
U1000-24
24
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
RUBBER HOSE
25
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
RUBB
ER H
OSE
PW1HoseType
PW2HoseType
EUROWASH HOSEPower Wash 1 Wire
Power Wash 2 Wire
ConstructionLiner: Synthetic rubberReinforcement: 1 braid of high tensile steel wireCover: Synthetic rubber Black (B)Blue (BL)Blue is fat resistant
ApplicationWater and/or steam at high temperatures, medium pressure,with detergent fluids for mobile cleaning equipment.
Temperature Range–40°F to +300°F (–40°C to +150°C).
FittingsEuropower ‘U’ series: 2-piece fittings
ConstructionLiner: Synthetic rubberReinforcement: 2 braids of high tensile steel wireCover: Synthetic rubberBlack (B)Blue (BL)Blue is fat resistant
ApplicationWater and/or steam at high temperatures, high pressure,with detergent fluids for mobile cleaning equipment.
Temperature Range–40°F to +300°F (–40°C to +150°C).
FittingsEuropower ‘U’ series: 2-piece fittings
HOSE TYPENOMINAL I.D. O.D.
MAX WORKINGPRESSURE
MINIMUMBURST
MINIMUM BEND RADIUS
AWEIGHT
INCHES MM IN MAX-MM AAPSI BAR PSI BAR INCHES MM LB/FT KG/M
EUROWASH-(COLOR REF)-06-PW1 3/8 9.5 0.780 19.8 3000 207 9000 620 5.2 130 0.296 0.44
DIMENSIONS:
DIMENSIONS:
FERRULE PART NO.
EXTERNAL SKIVENON SKIVE
U1000-06
HOSE TYPENOMINAL I.D. O.D.
MAX WORKINGPRESSURE
MINIMUMBURST
MINIMUM BEND RADIUS
AWEIGHT
INCHES MM IN MAX-MM AAPSI BAR PSI BAR INCHES MM LB/FT KG/M
EUROWASH-(COLOR REF)-06-PW2 3/8 9.5 0.843 21.4 5800 400 23200 1600 5.2 130 0.410 0.61
FERRULE PART NO.
EXTERNAL SKIVENON SKIVE
U2000-06
N/A
N/A
FERRULE PART NO.
NON SKIVE
N/A
N/A
N/A
EXTERNAL SKIVE
U2000-08
U2000-12
U2000-16
4SPHoseType
MULTISPIRAL HOSEMeets or exceeds requirements of EN856 4SP (formerly DIN 20023 4SP)
DIMENSIONS:
ConstructionLiner: Oil resistant synthetic rubberReinforcement: 4 plies of high tensile steel wireCover: Synthetic rubber
ApplicationPulsating pressure hydraulic applications
Temperature Range–40°F to +210°F (–40°C to +100°C)
FittingsEuropower ‘U’ series: 2-piece fittings
HOSE TYPE NOMINAL I.D. O.D.MAX WORKING
PRESSUREMINIMUM
BURSTMINIMUM
BEND RADIUSWEIGHT
INCHES MM IN MAX-MM PSI AABAR PSI BAR INCHES MM LB/FT KG/M
4SP-08 1/2 12.7 0.969 24.6 6018 415 24070 1660 9.0 230 0.645 0.96
4SP-12 3/4 19.0 1.268 32.2 5075 350 20300 1400 12.0 300 1.075 1.60
4SP-16 1 25.4 1.563 39.7 4640 320 18550 1280 13.5 340 1.364 2.03
RUBBER HOSE
26
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
N/A U2000-064SP-06 3/8 9.5 0.842 21.4 6450 445 26100 1800 6.0 150 0.422 0.630
N/A U2000-204SP-20 1 1/4 31.8 2.0 50.8 3045 210 12180 840 18.0 460 2.114 3.15
27
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
RUBB
ER H
OSE
HP-12 FP
HP-16 FP
HP-20 FP
HP-24 FP
HP-32 FP
FERRULE PART NO.
INTERNAL/EXTERNAL SKIVEHOSE TYPE
NOMINAL I.D. O.D.MAX WORKING
PRESSUREMINIMUM
BURSTMINIMUM
BEND RADIUSWEIGHT
INCHES MM IN MAX-MM PSI AABAR PSI BAR INCHES MM LB/FT KG/M
4SHHoseType
MULTISPIRAL HOSEMEETS OR EXCEEDS REQUIREMENTS OF DIN 856 4SH
DIMENSIONS:
ConstructionLiner: Oil resistant synthetic rubberReinforcement: 4 plies of high tensile steel wireCover: Black synthetic rubber
ApplicationImpulse pressure hydraulic applications greater than SAE 100 R12
Temperature Range–40°F to +210°F (–40°C to +100°C) with peaks up to +250°F (+120°C) depending on the medium
FittingsEuropower ‘HP’ series: 2-piece fittings
4SH-12 3/4 19.0 1.268 32.2 6090 420 24360 1680 11.02 280 1.0752 1.600
4SH-16 1 25.4 1.524 38.7 5510 380 22040 1520 13.40 340 1.384 2.060
4SH-20 1 1/4 31.8 1.780 45.2 4715 325 18850 1300 18.11 460 1.724 2.566
4SH-24 1 1/2 38.1 2.105 53.5 4205 290 16820 1160 22.05 560 2.298 3.420
4SH-32 2 50.8 2.681 68.1 3625 250 14500 1000 27.55 700 3.024 4.500
HOSE TYPENOMINAL I.D. NOMINAL O.D.
MAX WORKINGPRESSURE
MINIMUMBURST
MINIMUM BEND RADIUS
WEIGHT
INCHES MM IN MM PSI BAR PSI BAR INCHES MM LB/FT KG/M
R12-06 3/8 9.5 0.795 20.2 4000 276 16000 1104 5.12 130 0.437 0.65
R12-08 1/2 12.7 0.937 23.8 4000 276 16000 1104 7.09 180 0.538 0.80
R12-10 5/8 15.9 1.090 27.7 4000 276 16000 1104 7.87 200 0.780 1.16
R12-12 3/4 19.0 1.208 30.7 4000 276 16000 1104 9.45 240 0.853 1.27
R12-16 1 25.4 1.496 38.0 4000 276 16000 1104 11.81 300 1.284 1.91
R12-20 1 1/4 31.8 1.850 47.0 3000 207 12000 828 16.53 420 1.700 2.53
R12HoseType
MULTISPIRAL HOSEMEETS SAE 100 R12
DIMENSIONS:
ConstructionLiner: Oil resistant synthetic rubberReinforcement: 4 plies of high tensile steel wireCover: Grey synthetic rubber
ApplicationPulsating pressure hydraulic applicationsThis hose meets MSHA requirements of interim fire criteriaMSHA approval number, IC-188
Temperature Range–40°F to +210°F (–40°C to +100°C)
FittingsEuropower ‘U’ series 2-piece fittings
‘A’ series 1-piece fittings
FERRULE PART NO.
NON SKIVE
N/A
N/A
N/A
N/A
N/A
N/A
EXTERNAL SKIVE
U2000-06
U2000-08
U2000-10
U2000-12
U2000-16
U2000-20
28
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
RUBBER HOSE
29
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
RUBB
ER H
OSE
920HoseType
ConstructionLiner: Oil resistant synthetic rubberReinforcement: Up to 1" I.D. 4 plies spiral wire
11⁄4" - 2" I.D. 6 plies spiral wireRed cover: Oil and weather resistant synthetic rubber
ApplicationImpulse pressure hydraulic oil lines requiring flexibility,superior strength and high temperature.
Temperature Range–40°F to +225°F (–40°C to +107°C).
FittingsEuropower ‘HP’ series: 2-piece permanently swaged fittings
MULTISPIRAL HOSEEH 920 (Meets or exceeds SAE 100 R13)
DIMENSIONS:
HOSE TYPENOMINAL I.D. NOMINAL O.D.
MAX WORKINGPRESSURE
MINIMUMBURST
MINIMUM BEND RADIUS
WEIGHT
INCHES MM IN MAX-MM PSI BAR PSI BAR INCHES MM LB/FT KG/M
EH920-12 3/4 19.1 1.307 33.2 5000 345 20000 1380 9.5 240 1.068 1.59
EH920-16 1 25.4 1.567 39.8 5000 345 20000 1380 12.0 300 1.478 2.20
EH920-20 1 1/4 31.8 2.020 51.3 5000 345 20000 1380 16.5 415 2.480 3.69
EH920-24 1 1/2 38.1 2.315 58.8 5000 345 20000 1380 19.5 500 3.219 4.79
EH920-32 2 50.8 2.862 72.7 5000 345 20000 1380 25.0 635 5.027 7.48
FERRULE PART NO.
HP-12 FP
HP-16 FP
HP-20 Z
HP-24 Z
HP-32-920
INTERNAL/EXTERNAL SKIVE
THERMOPLASTIC
Performance
■ UV and ozone resistant with excellent shelf-life.
■ Cover resistant to most oils, chemicals, solvents anddetergents.
■ Good chemical resistance and inert to mostatmospheric conditions.
■ Outstanding flexibility throughout temperature range.
■ Good abrasion resistance.
■ By virtue of non-mandrel production, or need forrelease agents, Euroflow hose offers a significantlyhigher operating cleanliness. Smooth bore tubereduces pressure drop and heat build-up.
Machinery
An extensive range of factory and field swaging equipmentis available. Please consult our Customer ServicesDepartment.
Key Reference
✔ Excellent ● Limited resistance✘ Unsatisfactory ●● No data available✔* Excellent, but some permeability to gases. Outer
cover should be pin-pricked. Contact our TechnicalDepartment before specifying hose.
NYL6Nylon 6 NYL11 Nylon 11PEL Polyester ElastomerPTFE Polytetrafluoroethylene
Note
1. Resistance measured at ambient temperatures unlessotherwise stated.
2. None of the hoses are recommended for use wherethey will be exposed to intense high energy radiation,e.g. X-Rays.
We emphasise that although the data contained in thisguide is based primarily on laboratory tests, it does nottake into account all variables that can be encountered inactual use. Where doubt exists it may be advisable to testthe hose under controlled service conditions. If this is notpracticable, tests should be devised that simulate serviceconditions as closely as possible.
material compatability chart THERMOPLASTIC & PTFE
PTFE
PEL
HOSE TYPE
NYL6FLUIDS
NYL1
1
Aceton ✔ ✔ ✔ ✔
Acetylene ●● ✔ ✔ ✔
Air ✔* ✔* ✔* ✔
Air (200˚C) ●● ✘ ✘ ✔
Alcohols (aliphatic) ✔ ✔ ✔ ✔
Alkaline solutions (hydroxides) 50% ✔ ✔ ● ✔
Ammonium Hydroxide 25% ✔ ✘ ✘ ✔
Ammonia, liquid, anhydrous ✘ ✘ ✘ ✔
Ammonia gas ✔ ✘ ✘ ✔
Aroclor 1248 (chlorinated diphenyl hydraulic fluid) ●● ● ● ✔
ASTM Oil No. 1 ●● ✔ ✔ ✔
ASTM Oil No. 2 ●● ✔ ✔ ✔
ASTM Oil No. 2 ●● ✔ ✔ ✔
Beer ✔ ✔ ✔ ✔
Benzene (Benzol) ✔ ✔ ✔ ✔
Brake Fluid ●● ✔ ✘ ✔
Butane ✔* ✔* ✔* ✔
Butyl Acetate ✔ ✔ ✔ ✔
NYL1
1
PTFE
PEL
HOSE TYPE
NYL6FLUIDS
Carbon Dioxide (dry) ●● ✔* ✔* ✔
Carbon Tetrachloride ✔ ✔ ● ✔
Cellosolve Acetate ●● ✔ ● ✔
Cellosolve Butyl ●● ✔ ● ✔
Cellulubes (hydraulic fluid phosphate ester base) 150 ●● ✔ ✔ ✔
Cellulubes (hydraulic fluid phosphate ester base) 220 ●● ✔ ✔ ✔
Chlorinated solvents ● ✔ ✘ ✔
Chlorine (dry) ✘ ✘ ✘ ✘
Creosote ●● ✘ ✘ ✔
Cyclohexane ✔ ✔ ✔ ✔
Cyclohexanol ✔ ✔ ✔ ✔
Cyclohexanone ✔ ✔ ✔ ✔
Di Alphanol Phthalate (DAP) ●● ✔ ✔ ✔
Diesel Oil, DERV ✔ ✔ ✔ ✔
Diesel Oil, DERV 2472 Oil ●● ✔ ✔ ✔
Ethyl Acetate ✔ ✔ ✔ ✔
Ethylene Chloride ✔ ✔ ✘ ✔
Ethylene Glycol ●● ✔ ✔ ✔
For further information on material compatability, or if indoubt, please consult our Technical Department.
30
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
31
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THER
MOP
LAST
IC
FREON 11 ✔* ✔* ✘ ✔*
FREON 12 ✔* ✔* ✘ ✔*
FREON R134A ✔* ✔* ●● ✔*
FREON 21 ✔* ✔* ✔* ✘
FREON 22 ✔* ✔* ✔* ✘
Fire Resistant Hydraulic Fluid ✔ ✔ ✔ ✔
Fuel Oil ✔ ✔ ✔ ✔
Gasoline ✔ ✔ ✔ ✔
Hexane ✔ ✔ ✔ ✔
Hydrchlorine Acid (dilute) ✘ ✘ ✘ ✔
Hydrogen ●● ✔* ✔* ✔
Hydraulic Fluid – Petroleum base ●● ✔ ✔ ✔
Isopropyl Acetate ●● ✔ ✔ ✔
Kerosene ✔ ✔ ✔ ✔
Lorco Standard ‘L’ Oil ●● ✔ ✔ ✔
Lubricating Oil – Ester base ●● ✔ ✘ ✔
Lubricating Oils – Petroleum base ✔ ✔ ✔ ✔
Mobil Oil HFA ●● ✔ ✔ ✔
Mineral Oils ✔ ✔ ✔ ✔
Methanol (up to 40˚C) ✔ ✔ ● ✔
Methylene Chloride ● ✔ ✘ ✔
Methyl Ethyl Ketone ✔ ✔ ● ✔
Methyl Isobutyl Ketone ●● ✔ ✔ ✔
Naptha ●● ✔ ✔ ✔
Natural Gas ●● ✔* ✔* ✔
Nyvac 20 Oil ●● ✔ ✔ ✔
Nyvac 30 Oil ●● ✔ ✔ ✔
47 Octane to DEF 2401 – Hydraulic fluid ●● ✔ ✔ ✔
74 Octane to DEF 2401 – Silicate ●● ✔ ✔ ✔
80 Octane to DEF 2401 – Ester base ●● ✔ ✔ ✔
Perchoethylene ✔ ✔ ● ✔
Petrol ✔ ✔ ✔ ✔
Petroleum Oils (refined) ●● ✔ ✔ ✔
Petroleum Oils (sour) ●● ● ● ✔
Phenol ✘ ✘ ✘ ✔
Phenol (hot) 100˚C ✘ ✘ ✘ ✔
Phosphoric Acid 30% ✘ ● ✘ ✔
Propane ✔ ✔* ✔* ✔
Pydraul P-9 ●● ✔ ✔ ✔
Pydraul 150 ●● ✔ ✔ ✔
Pydraul A200 ●● ✔ ✔ ✔
Pydraul 280 ●● ✔ ✔ ✔
Pydraul 600 ●● ✔ ✔ ✔
Pydraul 625 ●● ✔ ✔ ✔
Shell FR Hydraulic Fluid ●● ✔ ✔ ✔
Skydrol ●● ✔ ✔ ✔
Skydrol 500H ●● ✔ ✔ ✔
Skydrol 7000 ●● ✔ ✔ ✔
Steam ✘ ✘ ✘ ✔
Tellus Oil No. 11 ●● ✔ ✔ ✔
Tellus Oil No. 21 ●● ✔ ✔ ✔
Tellus Oil No. 27 ●● ✔ ✔ ✔
Tellus Oil No. 33 ●● ✔ ✔ ✔
Toluene ✔ ✔ ✔ ✔
Trichlorethylene ● ✔ ✘ ✔
Tricresyl Phosphate ●● ✔ ●● ✔
Turpentine (White Spirits) ●● ✔ ✔ ✔
Vegetable Oils ●● ✔ ✘ ✔
Water at 70˚C (maximum) ●● ✔ ✔ ✔
Water at 99˚C (maximum) ●● ● ✘ ✔
Water (demineralised) ✔ ✔ ✔ ✔
Xylene ✔ ✔ ✔ ✔
NYL1
1
PTFE
PEL
HOSE TYPE
NYL6FLUIDS
NYL1
1
PTFE
PEL
HOSE TYPE
NYL6FLUIDS
THERMOPLASTIC & PTFEmaterial compatability chart
702HoseType
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
3/16 4.8
1/4 6.7
5/16 8.3
3/8 9.9
1/2 13.1
5/8 16.3
3/4 19.6
1 25.9
HOSETYPE
0.37 9.4
0.46 11.7
0.53 13.4
0.60 15.1
0.72 18.3
0.85 21.5
1.00 25.5
1.25 31.8
1.2 30
1.6 40
2.0 50
2.4 60
3.0 75
4.3 110
6.7 170
9.1 230
5250 362
4500 310
3500 240
3250 224
2750 190
1875 130
1750 120
1500 103
21000 1448
18000 1245
14000 963
13000 896
11000 758
7500 517
7000 483
6000 414
0.08 0.12
0.11 0.16
0.13 0.19
0.15 0.23
0.20 0.30
0.24 0.35
0.29 0.43
0.38 0.56
702-03
702-04
702-05
702-06
702-08
702-10
702-12
702-16
A multi-purpose high pressure hose suitable for hydraulicsystems. Type 702 is compatible with hydraulic oils, grease,fuel oils, mineral oils and most phosphate esters.
For water and water-based hydraulic fluids, temperature islimited to 70˚C.
This hose is also suitable for many industrial gases, e.g.Heliox (max. 25% O2), Argon, Nitrogen, Carbon Dioxide,Helium and Air. However, such applications should avoidenvironments which could lead to corrosion of hose wire.Refer to BS6596 for recommended factors of safety.
Hoses for gas applications require a pin-pricked cover —please specify at time of ordering.
Construction
Type 702 consists of an unplasticised polyester elastomertube reinforced with one braid of brass coated high tensilesteel wire with a black polyurethane outer cover.
Specification
This hose meets Europower ‘DMQ’ approved specificationswhen impulse tested at 125% of the stated dynamic workingpressure, using designated Europower permanently swagedfittings. Impulse, working and burst pressure requirements ofSAE100RI, BS4983 1984 TYPE 2, DIN 24951 pt2 and ISO3949 are also substantially exceeded (by up to 76%).
Performance
■ Min/max continuous service temperature range – 40˚C to100˚C (water and water-based fluids limited to 70˚C).
■ Low volumetric expansion giving excellent hydraulicresponse times.
■ Low ID to OD ratios, slim, lightweight (generally 65% ofequivalent rubber hose).
■ Electrical conductivity: less than 1.0 ohms/metre.■ Good chemical resistance and inert to most atmospheric
conditions.
Applications
■ Hydraulic Lines■ Mechanical Handling■ Construction Equipment■ Gas Applications■ Chemical Transfer
multipurpose 1 wireEUROFLOW TYPE
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved.
2-PIECE
U7000-03
U7000-04
U7000-05
U7000-06
U7000-8
U8000-10
U7000-12
U7000-16
FERRULE PART NO.
32
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THERMOPLASTIC
33
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THER
MOP
LAST
IC
711HoseType
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
1/4 6.7
5/16 8.3
3/8 9.9
1/2 13.1
HOSETYPE
FERRULE PART NO
0.46 11.7
0.53 13.4
0.60 15.1
0.72 18.3
1.6 40
2.0 50
2.4 60
3.0 75
4500 310
3500 240
3250 224
2750 190
18000 1245
14000 963
13000 896
11000 758
0.22 0.32
0.26 0.38
0.30 0.46
0.40 0.59
711-04
711-05
711-06
711-08
A multi-purpose high pressure hose suitable for hydraulicsystems. Type 711 is compatible with hydraulic oils, grease,fuel oils, mineral oils and most phosphate esters.
For water and water-based hydraulic fluids, temperature islimited to 70˚C.
This hose is also suitable for many industrial gases, e.g.Heliox (max. 25% O2), Argon, Nitrogen, Carbon Dioxide,Helium and Air. However, such applications should avoidenvironments which could lead to corrosion of hose wire.Refer to BS6596 for recommended factors of safety.
Hoses for gas applications require a pin-pricked cover —please specify at time of ordering.
Construction
Type 711 consists of two unplasticised polyester elastomertubes, each reinforced with one braid of brass coated hightensile steel wire. The hose is then extruded together with ablack polyurethane cover to form a ‘Siamese’ hose. Thisconstruction provides easier parting than a weldedconstruction.
Specification
This hose meets Europower ‘DMQ’ approved specificationswhen impulse tested at 125% of the stated dynamic workingpressure, using designated Europower permanently swagedfittings. Impulse, working and burst pressure requirements ofSAE100RI, BS4983 1984 TYPE 2, DIN 24951 pt2 and ISO3949 are also substantially exceeded (by up to 76%).
Performance
■ Min/max continuous service temperature range – 40˚Cto 100˚C (water and water-based fluids limited to 70˚C).
■ Low volumetric expansion giving excellent hydraulicresponse times.
■ Electrical conductivity: less than 1.0 ohms/metre.■ Good abrasion resistance.■ Excellent stability.
Applications
■ Mechanical Handling■ Construction Equipment■ Hydraulic Lines■ Supply/Return Lines
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved.
multipurpose 1 wire supertwinEUROFLOW TYPE
2-PIECE
U7000-04
U7000-05
U7000-06
U7000-08
703HoseType
A multi-purpose extra high pressure hose suitable forhydraulic systems. Type 703 is compatible with hydraulic oils,grease, fuel oils, mineral oils and most phosphate esters.
For water and water-based hydraulic fluids, temperature islimited to 70˚C.
This hose is also suitable for many industrial gases, e.g.Heliox (max. 25% O2), Argon, Nitrogen, Carbon Dioxide,Helium and Air. However, such applications should avoidenvironments which could lead to corrosion of hose wire.Refer to BS6596 for recommended factors of safety.
Hoses for gas applications require a pin-pricked cover —please specify at time of ordering.
Construction
Type 703 consists of an unplasticised polyester elastomertube reinforced with two braids of brass coated high tensilesteel wire, separated by a thermoplastic cushion interlayer toeliminate friction between braids and improve impulse life.The outer cover is black polyurethane.
Specification
This hose meets the Europower ‘DMQ’ approvedspecifications when impulse tested at 133% of the stateddynamic working pressure, using approved Europowerpermanently swaged fittings. The hose also meets theimpulse, working and burst pressure requirements ofDIN20022 2ST (except – 10) and exceeds SAE100R2 andBS3832 TYPE 2.
Performance
■ Min/max continuous service temperature range – 40˚Cto 100˚C (water and water-based fluids limited to 70˚C).
■ Low volumetric expansion giving excellent hydraulicresponse times.
■ Low ID to OD ratios, slim, lightweight (generally 76% ofequivalent rubber hose).
■ Electrical conductivity: less than 1.0 ohms/metre.
■ Good chemical resistance and inert to most atmosphericconditions.
Applications
■ Hydraulic Lines
■ Mechanical Handling
■ Construction Equipment
■ Gas Applications
■ Chemical Transfer
EUROFLOW TYPEmultipurpose 2 wire
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
1/4 6.7
5/16 8.3
3/8 9.9
1/2 13.1
5/8 16.3
3/4 19.6
1 25.9
HOSETYPE
FERRULE PART NO
0.54 13.7
0.60 15.2
0.67 17.0
0.80 20.2
0.92 23.4
1.07 27.1
1.35 34.3
1.6 40
2.0 50
2.4 60
3.0 75
4.3 110
6.7 170
9.1 230
5800 400
5000 350
4800 330
4000 275
3250 224
3100 215
2400 165
28000 1930
25000 1724
22000 1517
17000 1172
13000 896
13000 896
11000 758
0.21 0.31
0.23 0.35
0.28 0.42
0.34 0.51
0.42 0.62
0.50 0.73
0.65 0.98
703-04
703-05
703-06
703-08
703-10
703-12
703-16
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved.
2-PIECE
U8000-04
U8000-05
U8000-06
U8000-08
U8000-10
U8000-12
U1000-16
34
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THERMOPLASTIC
35
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THER
MOP
LAST
IC
722HoseType
SAE 100R7 BS4983: 1973
DIN 24951 pt 2 ISO3945
An all-purpose medium pressure hose suitable for manyhydraulic and pneumatic systems. Type 722 is compatiblewith hydraulic oils, grease, fuel oils, mineral oils and mostphosphate esters
For water and water-based hydraulic fluids, temperature islimited to 70˚C.
This hose is also suitable for many industrial gases, e.g.Heliox (max. 25% O2), Argon, Nitrogen, Carbon Dioxide,Helium and Air. Refer to BS6596 for recommended factors ofsafety.
Hose type 722 has a pin-pricked cover. For non-prickedcover specify type 822.
Construction
Type 722 comprises of an unplasticised polyester elastomertube reinforced with a single braid of polyester fibre, and ablack polyurethane outer cover.
Specification
The hose meet Europower ‘DMQ’ approval specificationswhen impulse tested at 125% of the stated dynamic workingpressure, using approved Europower permanently swagedfittings.
The hose also meets the following international standards:
SAE100R7, BS4983: 1973, DIN 24951 pt2 and ISO 3949.
Performance
■ Min/max continuous service temperature range – 40˚Cto 100˚C (water and water-based fluids limited to 70˚C).
■ Low ID to OD ratios, slim and lightweight.
■ First-rate stability — change in length better than ± 3%.
■ Excellent flexibility and flex fatigue resistance throughouttemperature range.
Applications
■ General Hydraulics
■ Mechanical Handling
■ Construction Equipment
■ Gas Applications
■ Machine Tools
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved. One piece fittings available in ‘B’ & ‘C’ Series.
SAE 100R7EUROFLOW TYPE
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
3/16 4.8
1/4 6.4
5/16 7.9
3/8 9.7
1/2 12.7
5/8 16.1
3/4 19.4
1 25.8
HOSETYPE
FERRULE PART NO
0.41 10.4
0.49 12.4
0.56 13.8
0.64 16.3
0.78 19.9
0.89 22.7
1.03 26.1
1.28 32.5
1.5 38
2.0 51
2.2 56
2.5 64
3.2 82
6.0 152
7.0 178
8.0 203
3000 210
2750 190
2500 170
2250 155
2000 140
1500 100
1250 90
1000 70
12000 820
11000 750
10000 690
9000 620
8000 550
6000 410
5000 340
4000 270
0.05 0.08
0.07 0.10
0.08 0.12
0.10 0.16
0.14 0.22
0.16 0.25
0.20 0.30
0.25 0.38
722-03
722-04
722-05
722-06
722-08
722-10
722-12
722-16
Options
1. Type 822 is available with a non-conductive,non-perforated orange cover.
2-PIECE
U9000-03
U7000-04
U7000-05
U7000-06
U8000-08
U8000-10
U8000-12
U1000-16
726HoseType
Performance
■ Min/max continuous service temperature range – 40˚Cto 100˚C (water and water-based fluids limited to 70˚C).
■ Low ID to OD ratios, slim and lightweight.■ First-rate stability — change in length better than ± 3%.■ Excellent flexibility and flex fatigue resistance throughout
temperature range.
Applications
■ General Hydraulics■ Mechanical Handling■ Construction Equipment■ Gas Applications■ Machine Tools
EUROFLOW TYPESAE 100R7 supertwin
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
1/4 6.4
5/16 7.9
3/8 9.7
1/2 12.7
HOSETYPE
FERRULE PART NO
0.49 12.4
0.56 13.8
0.64 16.3
0.78 19.9
2.0 51
2.2 56
2.5 64
3.2 82
2750 190
2500 170
2250 155
2000 140
11000 750
10000 690
9000 620
8000 550
0.14 0.21
0.16 0.24
0.20 0.32
0.28 0.43
726-04
726-05
726-06
726-08
SAE 100R7 BS4983: 1973
DIN 24951 pt 2 ISO3945
An all-purpose medium pressure hose suitable for manyhydraulic and pneumatic systems. Type 726 is compatiblewith hydraulic oils, grease, fuel oils, mineral oils and mostphosphate esters
For water and water-based hydraulic fluids, temperature islimited to 70˚C.
This hose is also suitable for many industrial gases, e.g.Heliox (max. 25% O2), Argon, Nitrogen, Carbon Dioxide,Helium and Air. Refer to BS6596 for recommended factors ofsafety.
Hose type 726 has a pin-pricked cover.
Construction
Type 726 consists of two unplasticised polyester elastomertubes, each reinforced with one braid of polyester fibre. Thehose is then extruded together with a black polyurethanecover to form a ‘Siamese’ hose. This construction provideseasier parting than a welded construction.
Specification
The hose meet Europower ‘DMQ’ approval specificationswhen impulse tested at 125% of the stated dynamic workingpressure, using approved Europower permanently swagedfittings.
The hose also meets the following international standards:
SAE100R7, BS4983: 1973, DIN 24951 pt2 and ISO 3949.
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved. One piece fittings available in ‘B’ & ‘C’ Series.
2-PIECE
U7000-04
U7000-05
U7000-06
U8000-08
36
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THERMOPLASTIC
37
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THER
MOP
LAST
IC
822HoseType
SAE 100R7 BS4983: 1973
DIN 24951 pt 2 ISO3945
An all-purpose medium pressure hose suitable for manyhydraulic applications where electrical non-conductivity isrequired, also suitable for grease, fuel oils, mineral oils andphosphate esters.
For water and water-based hydraulic fluids, temperature islimited to 70˚C.
Construction
Type 822 comprises of an unplasticised polyester elastomertube reinforced with a single braid of polyester fibre, and anon pin-pricked orange polyurethane outer cover.
Specification
The hose meet Europower ‘DMQ’ approval specificationswhen impulse tested at 125% of the stated dynamic workingpressure, using approved Europower permanently swagedfittings.
The hose also meets the following international standards:
SAE100R7, BS4983: 1973, DIN 24951 pt2 and ISO 3949.
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved. One piece fittings available in ‘B’ & ‘C’ Series.
Options
1. Type 722 is available with a perforated black cover.
Performance
■ Non-conductive (hose meets SAE 100R7 conductivityrequirements, wherein maximum leakage shall notexceed 50 micro amps when subjected to 75 kilovoltsper foot for 5 minutes).
■ Min/max continuous service temperature range – 40˚C to100˚C (water and water-based fluids limited to 70˚C).
■ Low ID to OD ratios, slim and lightweight.
■ First-rate stability — change in length better than ± 3%.
■ Excellent flexibility and flex fatigue resistance throughouttemperature range.
Applications
■ General Hydraulics
■ Mechanical Handling
■ Construction Equipment
■ Machine Tools
■ Hedge Cutters
■ Telephone & Utility Companies
orange non-conductive SAE 100R7EUROFLOW TYPE
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
3/16 4.8
1/4 6.4
5/16 7.9
3/8 9.7
1/2 12.7
5/8 16.1
3/4 19.4
1 25.8
HOSETYPE
FERRULE PART NO
0.41 10.4
0.49 12.4
0.56 13.8
0.64 16.3
0.78 19.9
0.89 22.7
1.03 26.1
1.28 32.5
1.5 38
2.0 51
2.2 56
2.5 64
3.2 82
6.0 152
7.0 178
8.0 203
3000 210
2750 190
2500 170
2250 155
2000 140
1500 100
1250 90
1000 70
12000 820
11000 750
10000 690
9000 620
8000 550
6000 410
5000 340
4000 270
0.05 0.08
0.07 0.10
0.08 0.12
0.10 0.16
0.14 0.22
0.16 0.25
0.20 0.30
0.25 0.38
822-03
822-04
822-05
822-06
822-08
822-10
822-12
822-16
2-PIECE
U9000-03
U7000-04
U7000-05
U7000-06
U8000-08
U8000-10
U1000-16
U8000-12
720HoseType
Performance
■ Min/max continuous service temperature range – 40˚Cto 100˚C. May be used with water and water-basedfluids to 70˚C continuous, 95˚C intermittent.
■ Low ID to OD ratio, slim and lightweight.
■ First-rate stability — change in length better than ± 3%.
■ Excellent flexibility and flex fatigue resistance throughouttemperature range.
Applications
■ Solvent Lines
■ Refrigeration Systems
■ Gas Lines
Options
1. Type 820 is available with a non-conductive,non-perforated orange cover.
EUROFLOW TYPEhigh specification SAE 100R7
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
3/16 4.8
1/4 6.4
5/16 7.9
3/8 9.7
1/2 12.7
5/8 16.1
3/4 19.4
1 25.8
HOSETYPE
FERRULE PART NO
0.41 10.4
0.49 12.4
0.56 13.8
0.64 16.3
0.78 19.9
0.89 22.7
1.03 26.1
1.28 32.5
1.5 38
2.0 51
2.2 56
2.5 64
3.2 82
6.0 152
7.0 178
8.0 203
3000 205
2750 187
2500 170
2250 155
2000 137
1500 100
1250 90
1000 70
12000 820
11000 750
10000 680
9000 620
8000 550
6000 410
5000 340
4000 270
0.05 0.08
0.07 0.10
0.08 0.12
0.10 0.16
0.14 0.22
0.16 0.25
0.20 0.30
0.25 0.38
720-03
720-04
720-05
720-06
720-08
720-10
720-12
720-16
SAE 100R7 BS4983: 1973
DIN 24951 pt 2 ISO3945
An all-purpose medium pressure hose suitable for manyhydraulic and pneumatic systems.
Type 720 is compatible with vegetable based oils, mostphosphate esters as well as hydraulic, mineral and fuel oilsand greases.
For water and water-based hydraulic fluids, temperature islimited to 70˚C continuous, 95˚C intermittent.
This hose is also suitable for many industrial gases, e.g.Heliox (max. 25% O2), Argon, Nitrogen, Carbon Dioxide, Heliumand Air. Refer to BS6596 for recommended factors of safety.
Hose type 720 has a pin-pricked cover.
Construction
Type 720 comprises of a nylon 11 tube reinforced with asingle braid of polyester fibre, and a black polyurethane outercover.
Specification
This hose meets Europower ‘DMQ’ approval specificationswhen impulse tested at 125% of the stated dynamic workingpressure, using approved Europower permanently swagedfittings.
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved. One piece fittings available in ‘B’ & ‘C’ Series.
U7000-04
–
–
–
–
–
–
U8000-08
2-PIECE
38
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THERMOPLASTIC
39
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THER
MOP
LAST
IC
737HoseType
SAE 100R8 BS4983 Type 2
ISO3945An all-purpose high pressure hose meeting SAE 100R8working pressure standards and benefiting from theincreased flexibility of SAE 100R7 dimensions. Suitable formany hydraulic and pneumatic systems., type 737 iscompatible with hydraulic oils, grease, fuel oils, mineral oilsand most phosphate esters.For water and water-based hydraulic fluids, temperature islimited to 70˚C.This hose is also suitable for many industrial gases, e.g.Heliox (max. 25% O2), Argon, Nitrogen, Carbon Dioxide,Helium and Air. Refer to BS6596 for recommended factors ofsafety.Hose type 737 has a non-pricked cover. For gas applicationsa pin-pricked cover is recommended which must bespecified at time of ordering.
Construction
Hose type 737 comprises of a polyester elastomer tubereinforced with a single braid of polyaramid fibre, and a blackpolyurethane outer cover.
Specification
The hoses meet Europower ‘DMQ’ approval specificationswhen impulse tested at 133% of the stated dynamic workingpressure, using approved Europower permanently swagedfittings.
The hose also meets the following international standards:
SAE100R8, BS4983 Type 2, ISO 3949-2.
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved. One piece fittings available in ‘B’ & ‘C’ Series.
Performance
■ Min/max continuous service temperature range – 40˚Cto 100˚C (water and water-based fluids limited to 70˚C).
■ Low ID to OD ratios, slim and lightweight.
■ First-rate stability — change in length maximum ± 2%.
■ Excellent flexibility and flex fatigue resistance throughouttemperature range.
Applications
■ General Hydraulics
■ Mechanical Handling
■ Pressure Jetting
■ Machine Tools
■ Construction Equipment
Options
1. Type 837 is available with a non-conductive,non-perforated orange cover.
Note
1. Also available as Supertwin 736.
SAE 100R8 (to 100R7 dimensions)EUROFLOW TYPE
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
3/16 5.1
1/4 6.5
5/16 8.3
3/8 9.8
1/2 13.0
HOSETYPE
FERRULE PART NO
0.41 10.4
0.49 12.3
0.57 14.5
0.63 15.9
0.78 19.7
1.5 38
2.0 51
2.2 56
2.5 64
3.2 82
5000 345
5000 345
4500 310
4000 275
3500 240
20000 1380
20000 1380
18000 1241
16000 1100
14000 965
0.05 0.08
0.07 0.11
0.09 0.14
0.10 0.15
0.13 0.20
737-03
737-04
737-05
737-06
737-08
U7000-04
U7000-05
U9000-03
U8000-08
U7000-06
2-PIECE
736HoseType
Performance
■ Min/max continuous service temperature range – 40˚Cto 100˚C (water and water-based fluids limited to 70˚C).
■ Low ID to OD ratios, slim and lightweight.
■ First-rate stability — change in length maximum ± 2%.
■ Excellent flexibility and flex fatigue resistance throughouttemperature range.
Applications
■ General Hydraulics
■ Mechanical Handling
■ Pressure Jetting
■ Machine Tools
■ Construction Equipment
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved. One piece fittings available in ‘B’ & ‘C’ Series.
EUROFLOW TYPESAE 100R8 supertwin (to 100R7 dims.)
SAE 100R8 BS4983 Type 2ISO3945
An all-purpose high pressure hose meeting SAE 100R8working pressure standards and benefiting from theincreased flexibility of SAE 100R7 dimensions. Suitable formany hydraulic and pneumatic systems, type 736 iscompatible with hydraulic oils, grease, fuel oils, mineral oilsand most phosphate esters.
For water and water-based hydraulic fluids, temperature islimited to 70˚C.
This hose is also suitable for many industrial gases, e.g.Heliox (max. 25% O2), Argon, Nitrogen, Carbon Dioxide,Helium and Air. Refer to BS6596 for recommended factors ofsafety.
Hose type 736 has a non-pricked cover. For gas applicationsa pin-pricked cover is recommended which must bespecified at time of ordering.
Construction
Type 736 consists of two unplasticised polyester elastomertubes, each reinforced with one braid of polyaramid fibre. Thehose is then extruded together with a black polyurethanecover to form a ‘Siamese’ hose. This construction provideseasier parting than a welded construction.
Specification
The hoses meet Europower ‘DMQ’ approval specificationswhen impulse tested at 133% of the stated dynamic workingpressure, using approved Europower permanently swagedfittings.
The hose also meets the following international standards:
SAE100R8, BS4983 Type 2, ISO 3949-2.
40
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THERMOPLASTIC
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
1/4 6.5
5/16 8.3
3/8 9.8
1/2 13.0
HOSETYPE
FERRULE PART NO
0.49 12.3
0.57 14.5
0.63 15.9
0.78 19.7
2.0 51
2.2 56
2.5 64
3.2 82
5000 345
4500 310
4000 275
3500 240
20000 1380
18000 1241
16000 1100
14000 965
0.14 0.21
0.18 0.27
0.20 0.31
0.26 0.39
736-04
736-05
736-06
736-08
U7000-04
U7000-05
U8000-08
U7000-06
2-PIECE
41
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THER
MOP
LAST
IC
U7000-04
U7000-05
U9000-03
U8000-08
U7000-06
837HoseType
SAE 100R8 BS4983 Type 2ISO3949-2
An all-purpose high pressure hose meeting SAE 100R8working pressure standards and benefiting from theincreased flexibility of SAE 100R7 dimensions. Suitable formany hydraulic and pneumatic systems., type 837 iscompatible with hydraulic oils, grease, fuel oils, mineral oilsand most phosphate esters.
For water and water-based hydraulic fluids, temperature islimited to 70˚C.
Construction
Hose type 837 comprises of a polyester elastomer tubereinforced with a single braid of polyaramid fibre, and anorange polyurethane outer cover.
Specification
The hose meets Europower ‘DMQ’ approval specificationswhen impulse tested at 133% of the stated dynamic workingpressure, using approved Europower permanently swagedfittings.
The hose also meets the following international standards:
SAE 100R8, BS4983 Type 2, ISO 3949-2.
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved. One piece fittings available in ‘B’ & ‘C’ Series.
Options
1. Type 737 is available with a non-perforated black cover.
Performance
■ Non-conductive (hose meets SAE 100R8 conductivityrequirements, wherein maximum leakage shall notexceed 50 micro amps when subjected to 75 kilovoltsper foot for 5 minutes).
■ Low ID to OD ratios, slim and lightweight.
■ First-rate stability — change in length maximum ± 2%.
■ Excellent flexibility and flex fatigue resistance throughouttemperature range.
■ Min/max continuous service temperature range – 40˚C to100˚C (water and water-based fluids limited to 70˚C).
Applications
■ General Hydraulics
■ Mechanical Handling
■ Pressure Jetting
■ Machine Tools
■ Construction Equipment
SAE 100R8 (to 100R7 dimensions)EUROFLOW TYPE
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
3/16 5.1
1/4 6.5
5/16 8.3
3/8 9.8
1/2 13.0
HOSETYPE
FERRULE PART NO
0.41 10.4
0.49 12.3
0.57 14.5
0.63 15.9
0.78 19.7
1.5 38
2.0 51
2.2 56
2.5 64
3.2 82
5000 345
5000 345
4500 310
4000 275
3500 240
20000 1380
20000 1380
18000 1241
16000 1100
14000 965
0.05 0.08
0.07 0.11
0.09 0.14
0.10 0.15
0.13 0.20
837-03
837-04
837-05
837-06
837-08
2-PIECE
714HoseType
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
STATICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
3/16 4.8
1/4 6.7
3/8 9.9
1/2 13.1
3/4 19.6
HOSETYPE
FERRULE PART NO
0.37 9.4
0.46 11.7
0.60 15.1
0.72 18.3
1.00 25.5
1.0 25
1.5 37
2.0 50
3.0 75
6.7 170
5440 375
4890 337
3625 250
3000 207
1750 120
21000 1448
18000 1245
13000 896
12000 828
7000 483
0.08 0.12
0.11 0.16
0.15 0.23
0.20 0.30
0.29 0.43
714-03
714-04
714-06
714-08
714-12
DYNAMICWORKINGPRESSURE
PSI BAR
5250 362
4500 310
3250 224
3000 207
1750 120
A high pressure, high performance, airless paint spray hosespecially designed to meet the exacting requirements of theindustry. Steel braid reinforcing ensures strength andguaranteed electrical conductivity.
This hose offers optimum resistance to a wide range of fluidsincluding paints, chlorinated solvents and other chemicals.Cover pin-pricked as standard.
Construction
Type 714 comprises of a nylon 6 tube reinforced with onebraid of brass coated high tensile steel wire. The blue outercover is polyurethane, other colours are available to specialorder.
Specification
This hose meets Europower ‘DMQ’ approved specificationswhen impulse tested at 125% of the stated dynamic workingpressure at bend radii defined in ISO 8028 and usingdesignated Europower permanently swaged fittings.
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved.
Performance
■ Min/max continuous service temperature range – 40˚Cto 100˚C.
■ Resistant to most chemicals, paints and solvents.
■ Excellent flexibility with small bend radius.
■ Superior and reliable electrical conductivity resistance inthe order of 1.0 ohms/metre.
■ Cover provides excellent abrasion resistance.
Applications
■ Airless Paint Spray Equipment
1 wire paint spray hose
EUROFLOW TYPE
U7000-03
U7000-04
U7000-06
U7000-08
U7000-12
2-PIECE
42
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THERMOPLASTIC
43
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THER
MOP
LAST
IC
715HoseType
An extra high pressure, high performance, airless paint sprayhose specially designed to meet the exacting requirements ofthe industry. Double steel braid reinforcing ensuresmechanical strength and guaranteed electrical conductivity.
This hose offers optimum resistance to a wide range of fluidsincluding paints, chlorinated solvents and other chemicals.Cover pin-pricked as standard.
Construction
Type 715 comprises of a nylon 6 tube reinforced with twobraids of brass coated high tensile steel wire, separated by athermoplastic cushion interlayer providing improved impulselife. The outer cover is blue polyurethane with other coloursavailable on request.
Specification
This hose meets Europower ‘DMQ’ approved specificationswhen impulse tested at 125% of the stated dynamic workingpressure at 80˚C and to bend radii stated in ISO 8028 usingapproved Europower permanently swaged fittings.
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved.
Performance
■ Min/max continuous service temperature range – 40˚Cto 100˚C.
■ Resistant to most chemicals, paints and solvents.■ Excellent flexibility with small bend radius.■ Superior and reliable electrical conductivity resistance in
the order of 1.0 ohms/metre.■ Cover provides excellent abrasion resistance.
Applications
■ Airless Paint Spray Equipment
EUROFLOW TYPE2 wire paint spray hose
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
STATICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
1/4 6.7
3/8 9.9
1/2 13.1
HOSETYPE
FERRULE PART NO
0.54 13.7
0.67 17.0
0.80 20.2
1.0 25
1.5 37
2.5 62
7000 483
5500 379
4250 293
28000 1930
22000 1517
17000 1172
0.21 0.31
0.28 0.42
0.34 0.51
715-04
715-06
715-08
DYNAMICWORKINGPRESSURE
PSI BAR
6170 425
5100 351
4250 293
U8000-04
U8000-06
U8000-08
2-PIECE
709HoseType
An extra high pressure, high performance, airless paint sprayhose specially designed to meet the exacting requirements ofthe industry. Double carbon steel wire braid reinforcingensures mechanical strength and guaranteed electricalconductivity.
This hose offers optimum resistance to a wide range of fluidsincluding paints, chlorinated solvents and other chemicals.Cover pin-pricked as standard.
Construction
Type 709 comprises of a nylon 11 tube reinforced with twobraids of brass coated high tensile carbon steel wire,separated by a thermoplastic cushion interlayer providingimproved impulse life. The outer cover is blue polyurethanewith other colours available on request.
Specification
This hose meets Europower ‘DMQ’ approved specificationswhen impulse tested at 125% of the stated dynamic workingpressure at 80˚C and to bend radii stated in ISO 8028 usingapproved Europower permanently swaged fittings.
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved.
Performance
■ Min/max continuous service temperature range – 40˚Cto 100˚C.
■ Resistant to most chemicals, paints and solvents.
■ Excellent flexibility with small bend radius.
■ Superior and reliable electrical conductivity resistance inthe order of 1.0 ohms/metre.
■ Cover provides excellent abrasion resistance.
Applications
■ Airless Paint Spray Equipment
■ Two-part Polyurethane Foams
EUROFLOW TYPE2 wire paint spray hose(for aggressive applications)
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR LB/FT KG/M
1/4 6.7
3/8 9.9
1/2 13.1
3/4 19.6
1 25.9
HOSETYPE
FERRULE PART NO
0.54 13.7
0.67 17.0
0.80 20.2
1.07 27.1
1.35 34.3
1.0 25
1.5 37
2.5 62
6.7 170
9.1 230
28000 1930
22000 1517
17000 1172
13000 896
11000 758
0.21 0.31
0.28 0.42
0.34 0.51
0.50 0.73
0.65 0.98
709-04
709-06
709-08
709-12
709-16
DYNAMICWORKINGPRESSURE
PSI BAR
6170 425
5100 351
4250 293
3100 215
2750 190
U8000-04
U8000-06
U8000-08
U8000-12
U1000-16
2-PIECE
44
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THERMOPLASTIC
45
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THER
MOP
LAST
IC
754HoseType
Type 754 is a very high pressure, high performance airlesspaint spray hose specially designed to meet the exactingrequirements of the industry. Also suitable for hydraulic hoseapplications. Steel braid reinforcing ensures strength andguaranteed electrical conductivity.
This hose offers superior resistance to a wide range of fluidsincluding paints, chemicals and chlorinated solvents. Coverpin-pricked as standard.
Polyaramid/wire construction offers light weight, flexibilityand tighter bend radii in comparison with traditional multispiral designs.
Construction
Type 754 comprises of a nylon 11 tube reinforced with abraid of polyaramid yarn, a polyester interlay, a single braidof high tensile brass coated carbon steel wire and a blackpolyurethane outer cover.
Specification
The hose meets Europower ‘DMQ’ approved specificationswhen impulse tested at 125% of the stated dynamic workingpressure, using designated Europower permanently swagedfittings.
Fittings
Europower ‘ET’ series non-skived permanently swagedfittings are fully ‘DMQ’ approved.
Performance
■ Min/max continuous service temperature range – 40˚Cto 100˚C (water and water-based fluids limited to 70˚C).
■ Superior resistance to most chemicals, paints andsolvents.
■ Excellent flexibility with small bend radius.
■ Superior and reliable electrical conductivity resistance inthe order of 1.0 ohms/metre.
■ Cover provides excellent abrasion resistance.
■ Lightweight and flexible in comparison with conventionalmultispiral designs.
Applications
■ Airless Paint Spray Equipment
■ Two-part Polyurethane Foams
■ Chemical Transfer
■ General Hydraulic Applications
very high pressure hoseEUROFLOW TYPE
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
1/4 6.6
3/8 9.8
1/2 13.1
HOSETYPE
FERRULE PART NO
0.54 13.7
0.68 17.3
0.82 20.8
1.5 38
3.5 89
5.0 127
10000 690
8000 552
6500 448
40000 2760
32000 2208
26000 1792
0.155 0.231
0.216 0.321
0.278 0.414
754-04
754-06
754-08
ET04-352
ET06-754
ET08-754
2 PIECE
755HoseType
Performance
■ Min/max continuous service temperature range – 40˚Cto 100˚C (water and water-based fluids limited to 70˚C).
■ Superior resistance to most chemicals, paints andsolvents.
■ Excellent flexibility with small bend radius.
■ Superior and reliable electrical conductivity resistance inthe order of 1.0 ohms/metre.
■ Cover provides excellent abrasion resistance.
■ Lightweight and flexible in comparison with conventionalmultispiral designs.
Applications
■ Airless Paint Spray Equipment
■ Two-part Polyurethane Foams
■ Chemical Transfer
■ General Hydraulic Applications
EUROFLOW TYPEvery high pressure hose
Type 755 is a very high pressure, high performance airlesspaint spray hose specially designed to meet the exactingrequirements of the industry. Also suitable for hydraulic hoseapplications. Steel braid reinforcing ensures strength andguaranteed electrical conductivity.
This hose offers superior resistance to a wide range of fluidsincluding paints, chemicals and chlorinated solvents. Coverpin-pricked as standard.
Polyaramid/wire construction offers light weight, flexibilityand tighter bend radii in comparison with traditional multispiral designs.
Construction
Type 755 comprises of a nylon 11 tube reinforced with twobraids of polyaramid yarn and a single braid of high tensilebrass coated carbon steel wire with a polyester interlay, anda black polyurethane outer cover.
Specification
The hose meets Europower ‘DMQ’ approved specificationswhen impulse tested at 125% of the stated dynamic workingpressure, using designated Europower permanently swagedfittings.
Fittings
Europower ‘ET’ series non-skived permanently swagedfittings are fully ‘DMQ’ approved.
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
1/2 13.1
3/4 19.6
1 25.9
HOSETYPE
FERRULEPART NO
0.90 22.9
1.16 29.5
1.46 37.1
5.0 127
8.0 203
10.0 254
8500 586
6500 448
4750 328
34000 2344
26000 1792
19000 1312
0.325 0.484
0.448 0.666
0.614 0.914
755-08
755-12
755-16
ET08-755
ET12-755
ET16-755
2 PIECE
46
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THERMOPLASTIC
47
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THER
MOP
LAST
IC
352HoseType
Type 352 is an extra high performance hose designed to givesuperior dynamic and mechanical performance, whilstservice life and flexibility remain paramount.
Suitable for high pressure hydraulic systems and compatiblewith hydraulic oils, grease, fuel oils, mineral oils and mostphosphate esters.
Construction
Type 352 comprises of a polyester elastomer tube reinforcedwith a braid of polyaramid yarn, a polyester interlay, a singlebraid of carbon steel wire and a black polyurethane outercover.
Specification
The hoses meet Europower ‘DMQ’ approval specificationswhen impulse tested at 110% of the stated dynamic workingpressure, using approved ‘JET’ series Europowerpermanently swaged fittings.
Fittings
Europower ‘ET’ series non-skived permanently swagedfittings are fully ‘DMQ’ approved.
Options
1. Type 352 hose is available in welded twin construction inall sizes. Specify as 352 followed by WT and appropriatedash number, e.g. 352WT-04.
Performance
■ Min/max continuous service temperature range – 40˚Cto 100˚C (water and water-based fluids limited to 70˚C).
■ Low volumetric expansion giving excellent hydraulicresponse times.
■ Low ID to OD ratios.
■ First-rate stability — change in length better than ± 1%.
■ Superior flexibility and bend radii in comparison toconventional multispiral designs.
■ Each length is proof pressure tested.
Applications
■ High Pressure Hydraulic Systems
■ High Pressure Pumps
■ Rescue Equipment
■ Jacking Systems
extra high pressure hoseEUROFLOW TYPE
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
1/4 6.6
3/8 9.8
HOSETYPE
FERRULEPART NO
0.54 13.7
0.74 18.8
1.5 38
3.75 95
10000 700
10000 700
40000 2800
40000 2800
0.15 0.23
0.24 0.35
352-04
352-06
ET04-352
ET06-352
2 PIECE
852HoseType
Performance
■ Min/max continuous service temperature range – 40˚Cto 100˚C (water and water-based fluids limited to 70˚C).
■ Low ID to OD ratios.
■ First-rate stability — change in length better than ± 2%.
■ Superior flexibility and bend radii in comparison toconventional multispiral designs.
■ Each length is proof pressure tested.
■ Non-conductive (Hose meets SAE 100R8 conductivityrequirements, wherein maximum leakage shall notexceed 50 microamps when subjected to 75 kilovolts perfoot for 5 minutes).
■ Low volumetric expansion giving excellent hydraulicresponse time.
■ Corrosion resistant.
Applications
■ High Pressure Hydraulic Systems
■ High Pressure Pumps
■ Rescue Equipment
■ Jacking Systems
EUROFLOW TYPEhigh pressure non-conductive
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
1/4 6.6
HOSETYPE
FERRULEPART NO
0.57 14.5 1.5 38 10000 700 40000 2800 0.11 0.16852-04 ET04-852
Type 852 is an extra high performance non-conductive hosedesigned to give superior dynamic and mechanicalperformance, while service life and flexibility remainparamount.
Suitable for high pressure hydraulic systems and compatiblewith hydraulic oils, grease, fuel oils, mineral oils and mostphosphate esters.
Construction
Type 852 comprises of a polyester elastomer tube reinforcedwith two braids of high strength polyaramid fibre yarn withan orange polyurethane outer cover.
Specification
The hoses meet Europower ‘DMQ’ approval specificationswhen impulse tested at 110% of the stated dynamic workingpressure, using approved ‘JET’ series Europowerpermanently swaged fittings.
Fittings
Europower series ‘ET’ non-skived permanently swagedfittings are fully ‘DMQ’ approved.
Options
1. Type 852 hose is available in welded twin construction.Specify as 852 followed by WT and appropriate dashnumber, e.g. 852WT-04.
2 PIECE
48
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THERMOPLASTIC
49
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THER
MOP
LAST
IC
9038HoseType
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
3/8 9.9
1/2 13.2
HOSETYPE
FERRULEPART NO
0.64 16.1
0.76 19.3
4.5 112
6.0 150
2250 155
2000 140
9000 620
8000 550
0.10 0.15
0.12 0.18
9038-06
9038-08
U7000-06
–
SAE 100R7 BS4983: 1973DIN 24951 pt 2 ISO3945
A medium pressure hose specifically designed forrefrigeration systems using R22 and R134A where very lowpermeability is required.
Construction
Type 9038 comprises of a nylon tube reinforced with adouble braid of polyester yarn fully bonded, with a blackpolyurethane outer cover, pin pricked to allow effusion oftrapped gases.
Specification
The hoses meet Europower ‘DMQ’ approved specificationswhen impulse tested at 125% of the stated dynamic workingpressure, using approved Europower ‘X’ series permanentlyswaged fittings.
The hoses meet the following international standards:
SAE100R7, BS4983: 1973, DIN 24951 pt2 and ISO 3949.
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved. One piece fittings available in ‘B’ Series.
Options
1. Type 9038 hose is available in welded twin constructionin all sizes. Specify as 9038 followed by WT andappropriate dash number, e.g. 9038WT-06.
2. Colour options are available with 500M as minimumorder quantity for any special colour. Black as standard.Welded twin available as mixed colour coding.
Performance
■ Very low permeability to refrigeration gases. Details onrequest.
■ Suitable for use with R22, R134A.
■ Min/max continuous service temperature range – 40˚Cto 100˚C. Intermittantly up to 120˚C.
■ Low ID to OD ratios, slim and lightweight.
■ First-rate stability — change in length better than ± 3%.
Applications
■ Refrigeration Systems using R22, R134A (for alternativerefrigerants please contact our Customer ServicesDepartment)
textile braid refrigeration hoseEUROFLOW TYPE
2 PIECE
9081HoseType
Performance
■ Min/max continuous service temperature range-55˚C to 100˚C.
■ Excellent flex fatigue resistance of outer cover..
■ Excellent flexibility throughout the temperature range..
■ Low ID to OD ratios, slim and lightweight.
■ Small bend radius
■ First rate stability–change in length better than ±3%.
Applications
■ Forklift mast applications.
■ Applications where quick change of temperature underdynamic applications may cause premature failure ofstandard thermoplastic hose.
EUROFLOW TYPEcold temperature forklift hose
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
3/8 9.9
HOSETYPE
FERRULEPART NO
0.67 17 2.4 60 3000 210 12000 830 0.12 0.189081-06 U8000-06
Type 9081 has been designed specifically for forkliftapplications where there is a fast and frequent change oftemperature eg cold rooms combined with fast change inpressure.
The hose has a special wear resistant cover, whichguarantees smooth running of the hose over the mast pulleys- even at low temperature. Lifetime of the hose is prolongedby the elimination of the “cover cracking” phenomenon.
The hose has completed 200,000 flex wear resistance cyclesat low temperatures, making this hose extremely suitable forforklift mast applications.
Type 9081 is compatible with hydraulic oils, grease, fuel oils,mineral oils and most phosphate esters.
Construction
Type 9081 comprises of a polyester elastomer tubereinforced by 2 braids of polyester fibre, fully bonded, with ablack polyester elastomer pinpricked cover.
Specification
The hoses meet Europower ‘DMQ’ approval specificationswhen impulse tested at 133% of the stated dynamic workingpressure, using approved Europower permanently swagedfittings.
Fittings
Europower ‘U’ series fittings are fully ‘DMQ’ approved.
Options
Type 9081 is also available in welded twin construction - partnumber 9081 WT-hose size.
2 PIECE
THERMOPLASTIC
50
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
51
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THER
MOP
LAST
IC
9086HoseType
Performance
■ Min/max continuous service temperature range-40˚C to 100˚C.
■ Low ID to OD ratios, lightweight.
■ Excellent flexibility with small bend radius.
■ Cover provides excellent abrasion resistance.
Applications
■ Air cylinder charging.
EUROFLOW TYPEair cylinder charging hose
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
3/16 5.0
HOSETYPE
FERRULEPART NO
0.406 10.3 1.5 38 6000 414 24000 1656 0.05 0.089086-03 U9000-03
A high pressure air cylinder charging hose specificallydesigned to meet the exacting requirements of the industry.
Suitable for breathing air applications.
Construction
The hose comprises polyester elastomer tube, reinforcedwith one braid of para aramid yarn. The blue outer cover ispolyurethane.
Cover is pinpricked as standard.
Fittings
Europower ‘U’ series fittings are fully ‘DMQ’ approved.
2 PIECE
9088HoseType
Performance
■ Low volumetric expansion giving excellent hydraulicresponse times.
■ Low ID to OD ratios, slim and lightweight.
■ First rate stability–change in length better than ±3%.
■ Excellent flexibility and flex fatigue resistance throughouttemperature range.
■ Min/max continuous service temperature range -40°C to100°C (water and water-based fluids limited to 70°C).
Applications
■ Pilot Lines
■ Medium Pressure Hydraulic Lines.
■ Grease Lines.
EUROFLOW TYPEpilot line hose
A medium pressure hose suitable for hydraulic, grease andpilot lines. Type 9088 is compatible with hydraulic oils,grease, fuel oils, mineral oils and most phosphate esters.
For water and water-based hydraulic fluids temperature islimited to 70°C.
-9088 has a non-pricked cover.
Construction
Type 9088 is comprised of a polyester elastomer tubereinforced with one braid of brass coated high tensile carbonsteel wire and black polyurethane outer cover.
Specification
The hose meets Europower ‘DMQ’ approved specificationswhen impulse tested at 125% of the stated dynamic workingpressure, using approved Europower permanently swagedfittings.
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved.
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
MINIMUMBEND
RADIUS
DYNAMICWORKINGPRESSURE
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM PSI BAR PSI BAR LB/FT KG/M
0.26 6.7
0.39 9.9
0.50 13.1
HOSETYPE
FERRULEPART NO
0.420 10.7
0.555 14.0
0.720 18.3
1.18 30
1.77 45
3.00 75
2750 190
2030 140
2030 140
11000 760
8100 560
8100 560
0.08 0.12
0.12 0.17
0.20 0.30
9088-04
9088-06
9088-08
–
–
–
2 PIECE
52
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THERMOPLASTIC
53
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
PTFE
Permeation & Corrosion through aHose Liner made from TEFLON®
Permeation rate of a given chemical through a linermade from TEFLON® is difficult to quantify in mostcases.
Diffusion of a chemical through a hose liner is extremelycomplex. Even under laboratory conditions, it dependson factors such as temperature, concentration of vapourpressure, flow-regime (static system or flow underlaminar or turbulent conditions), polymer crystallinityand micro-porosity.
In addition, people often require permeation rates of achemical in the presence of solvents and otherreactants. These other components can have a dramaticeffect on the permeation rates because they caninteract with the fluid (through association, complex-information or coupled-diffusion) or with the TEFLON®
(through absorption, swelling, plasticisation or cluster-information).
Permeation in plastics is also an activated process —
i.e. it has an activation energy which determines howsensitive the process is to temperature change. Inpractice, this means that, when comparing thepermeation rate of a chemical through two plastics (Aand B), it is impossible to predict the effect of changingtemperature from single permeation rate values. Forexample, if at 20˚C bromine permeates plastic A at rate‘x’ and plastic B at rate ‘2x’, it is wrong to assume that itwill also permeate twice as quickly through plastic B at100˚C. In fact the opposite could be observed at 100˚C ifthe activation energy energy for bromine diffusion in Bwas much lower than in A.
Permeation of High Pressure Gases
From this it can be seen that it is equally difficult tocomment on the permeation of high pressure gases.
Indeed, field testing under normal conditions of use isprobably the only means of determining the correct rate.
In all cases, our advice is always to subject a piece ofhose to a trial under field conditions to determine itsprecise performance and suitability for use.Based on information kindly supplied by Du Pont Fluoropolymer Division,Geneva.
® Du Pont Registered Trade Mark.
factors of suitabilityPTFE TYPE
Pressure Temperature Rating
Approximate Temperature Derating Curves for PTFE Hose.
VARIATION OF WORKING PRESSURE WITH TEMPERATURE FOR HOSE TYPES EFL1 & EFH1
PERCENTAGE OF MAXIM
UM W
ORKING PRESSURE (%)
-60 -40 -20 0 20 40 60 80 100 120 140 160 180 200 220 240 260
100
90
80
70
60
50
THoseType
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
NOMINALWALL
THICKNESS
MINIMUMBEND
RADIUS
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM IN MM PSI BAR LB/FT KG/M
1/8 3.6
3/16 5.1
1/4 6.6
5/16 8.3
3/8 9.8
1/2 13.1
5/8 16.1
3/4 19.4
1 25.8
HOSETYPE
FERRULEPART NO
0.25 6.2
0.32 8.0
0.38 9.5
0.43 10.8
0.49 12.3
0.63 16.0
0.75 19.1
0.88 22.4
1.13 28.7
0.04 1.02
0.03 0.76
0.025 0.64
0.025 0.64
0.025 0.64
0.035 0.89
0.035 0.89
0.035 0.89
0.04 1.02
1.0 25
2.0 51
3.0 76
4.0 102
4.5 114
5.0 127
6.0 152
8.0 203
12.0 305
13000 897
12000 828
11000 759
9000 621
8000 552
6000 414
5500 379
4500 310
3500 241
0.06 0.09
0.06 0.09
0.07 0.10
0.07 0.11
0.09 0.14
0.15 0.23
0.18 0.27
0.22 0.32
0.30 0.45
EFL1-02
EFL1-03
EFL1-04
EFL1-05
EFL1-06
EFL1-08
EFL1-10
EFL1-12
EFL1-16
–
U7000-03
U7000-04
U7000-05
U7000-06
U7000-08
U8000-10
U7000-12
U7000-16
DYNAMICWORKINGPRESSURE
PSI BAR
3250 224
3000 207
2750 190
2250 155
2000 138
1500 103
1375 95
1125 78
875 60
A smooth bore PTFE hose suitable for many severeapplications involving solvents, paints, gases, fuels, hydraulicoils and many others where requirements of hightemperature, medium pressure, chemical resistance andflex-life are paramount.
Construction
Type EFL1 comprises of a TEFLON® 62 liner with an A.I.S.I.304 Stainless Steel outer braid.
Specification
This hose meets Europower ‘DMQ’ approval specificationwhen using the designated Europower permanently swagedfittings.
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved.
Applications
■ Chemical Transfer
■ Steam Transfer
■ High/Low Temperature Applications
■ Solvent Transfer
■ Compressor Discharge
■ Diesel/Petrol Feed
■ Mould Heating Hot Oil
Performance
■ Min/max continuous service temperature range – 60˚Cto 260˚C.
■ Excellent dielectric properties independent of frequencyand temperature (non-conductive).
■ Virtually inert to chemical attack.
■ Non-inflammable.
■ Excellent fatigue resistance, particularly in applicationsinvolving flexing and vibration.
■ 4:1 Safety Factor.
Note
1. EFL1-02 requires special inserts and ferrules, to beadvised on order.
2. Not recommended for impulse pressure applicationswithout prior consultation with our Technical Department.
® Du Pont Registered Trade Mark
standard wall PTFE hosePTFE TYPE
2 PIECE
54
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
PTFE
55
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
PTFE
HHoseType
A smooth bore heavy PTFE hose suitable for many severeapplications involving solvents, paints, gases, fuels, hydraulicoils and many others where requirements of hightemperature, medium pressure, chemical resistance andflex-life are paramount.
Type EFH1 is more robust than type EFL1 and is particularlysuitable for applications involving extreme low temperatureflexing and thermal cycling.
Construction
Type EFH1 comprises of a TEFLON® 62 heavy wall liner withan A.I.S.I. 304 Stainless Steel outer braid.
Specification
This hose meets Europower ‘DMQ’ approval specificationwhen using the designated Europower permanently swagedfittings.
Fittings
Europower ‘U’ series non-skived permanently swaged fittingsare fully ‘DMQ’ approved.
Applications
■ Chemical Transfer
■ Steam Transfer
■ High/Low Temperature Applications
■ Compressor Discharge
■ Diesel/Petrol Feed
■ Mould Heating Hot Oil
PTFE TYPEheavy wall PTFE hose
NOMINALINSIDE
DIAMETER
NOMINALOUTSIDE
DIAMETER
NOMINALWALL
THICKNESS
MINIMUMBEND
RADIUS
MINIMUMBURST
PRESSUREWEIGHT
IN MM IN MM IN MM IN MM PSI BAR LB/FT KG/M
1/4 6.6
5/16 8.3
3/8 9.8
1/2 13.1
5/8 16.1
3/4 19.4
1 25.8
HOSETYPE
FERRULEPART NO
0.39 9.91
0.45 11.4
0.52 13.2
0.64 16.1
0.79 19.9
0.91 23.1
1.15 29.21
0.04 1.02
0.04 1.02
0.04 1.02
0.04 1.12
0.044 1.12
0.047 1.19
0.047 1.19
1.5 38
2.2 56
2.5 64
3.5 89
4.5 114
5.75 146
10.0 254
11000 759
9000 621
8000 552
6000 414
5500 379
4500 310
3500 241
0.09 0.13
0.09 0.14
0.11 0.17
0.17 0.26
0.21 0.31
0.25 0.37
0.32 0.47
EFH1-04
EFH1-05
EFH1-06
EFH1-08
EFH1-10
EFH1-12
EFH1-16
U7000-04
U7000-05
U7000-06
U7000-08
U8000-10
U7000-12
U7000-16
DYNAMICWORKINGPRESSURE
PSI BAR
2750 190
2250 155
2000 138
1500 103
1375 95
1125 78
875 60
Performance
■ Min/max continuous service temperature range – 60˚Cto 260˚C.
■ Excellent dielectric properties independent of frequencyand temperature (non-conductive).
■ Virtually inert to chemical attack.
■ Non-inflammable.
■ Excellent fatigue resistance, particularly in applicationsinvolving flexing and vibration.
■ Greater kink resistance.
■ 4:1 Safety Factor.
Note
1. Not recommended for impulse pressure applicationswithout prior consultation with our Technical Department.
® Du Pont Registered Trade Mark
2 PIECE
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
56
DM&Q PROGRAMAccepted industry standards are fine, as far as they go,
but remember that standards such as DIN and SAE applyto the hose only, and not to the end connection or its
integrity with the hose. Mixing untested hose and fittingsfrom a variety of sources with assembly techniques
based on trial and error, rather than properly structureddevelopment work and hours of impulse testing is, regret-
tably, an all too common occurrence – as common ashydraulic hose assembly failure, in fact.
Yet with your hydraulic life-blood at risk, it is vital that thewhole assembly has complete integrity, is guaranteed to
work and proven to be completely reliable.
The DM&Q emblem provides just this assurance andguarantees that a hose assembly has been Designed,
Matched and Qualified for total integrity and maximum performance.
Components are Designed – using the most advancedcomputer technology – to complement each type anddimension of hose perfectly, and Matched by highly
trained and specially qualified technicians to provide per-fect couplings every time. Finally, the complete assemblyis Qualified using the most rigorous testing procedures atour own test house, to guarantee that it will measure up
to the most exacting performance demands.
Instead of the risks of “mix-and-match” hose compo-nents, look for the DM&Q emblem. It is exclusive to
Europower hose assemblies and is your guarantee of per-formance assurance.
DMQ is a Europower Hydraulics Registered Trademark.
INTEGRATED SUPPLIER PROGRAMOur DM&Q program has shown that not all hydraulichose assemblies are created equal – but even that is
not the whole story.
By effectively becoming part of a customer’s designteam, Europower can not only ensure the integrity
of the individual components, but also advise on the system layout.
This is called the Integrated Supplier Program and it plays a vital part in the quality equation.
Unsuitable installation, for example, can threaten the effi-ciency of an otherwise adequate system. Inconsistent
flow conditions, twists in the hose, tight bends and poorhose assembly routing can cause premature failure.
The design and installation of hose assemblies into com-plex machinery is inevitably one of the last tasks to be
undertaken and quality is often compromised by the immense pressures to meet very tight prototype
and production deadlines
That is why Europower’s Integrated Supplier Programincludes a closely-knit team of qualified engineers cover-ing sales, design, cost and quotations and methods engi-neering. They will not disappear the moment the order
pad is signed. You can rely on their expertise to nurse thejob through internal systems until production deliveries
are running regularly and consistently. It is this nursery approach that enables the smooth
transition from prototype to production.
Therefore, what the Integrated Supplier Program offers isthe most cost effective solution to the problem. What’smore, the cost is, for the first time, a single, known and
quantifiable cost because the unpredictable cost of failure– of downtime and warranty claims –
is effectively removed from the equation.
Integrated Supplier Program is a Europower Hydraulics Registered Trademark.
GENERAL HOSE ENDSINFORM
ATION
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
57
The ABC’s of Ordering Europower Inc.One Piece Hose Ends
■ To order the standard 2-piece Hose End use the ‘U’part number provided. i.e. U02BM03
■ To order the one piece Rubber Hose End substitute an‘A’ for the ‘U’ i.e. U02BM03 A02BM03*Can be used on the following hoses:
• CITISN • SAE 100R16 • SAE100R12 • Europulse 2
• C2T2SN • SAE 100R17 • 4SP
■ To order the one-piece Thermoplastic Hose End thatuses U7000 Ferrules substitute a ‘B’ for the ‘U’i.e. U02BM03 B02BM03
■ To order the one-piece Thermoplastic Hose End thatuses U8000 Ferrules substitute a ‘C’ for the ‘U’i.e. U02BM03 C02BM03
•Please reference Hose type to find the Ferrule need-ed for the Thermoplastic one-piece Hose End.
GENE
RAL
HOSE
END
SIN
FORM
ATIO
N
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
58
SKIVED CRIMPED FERRULE
SKIVED CRIMPED FERRULE
FERRULES
See page 58 for how to order one-piece hose ends
NOMINAL HOSE BOREmm in dash PART NUMBER Dim A Dim B
5 3/16 03 U1000-03 17.4 22.8
6 1/4 04 U1000-04 20.0 30.5
8 5/16 05 U1000-05 20.0 30.5
10 3/8 06 U1000-06 23.0 32.0
12 1/2 08 U1000-08 28.5 34.0
16 5/8 10 U1000-10 31.7 36.8
19 3/4 12 U1000-12 35.0 42.7
25 1 16 U1000-16 42.8 50.8
31 1-1/4 20 U1000-20 50.7 59.0
38 1-1/2 24 U1000-24 – –
51 2 32 U1000-32 71.4 73.8
NOMINAL HOSE BOREmm in dash PART NUMBER Dim A Dim B
5 3/16 03 U2000-03 18.0 22.8
6 1/4 04 U2000-04 22.0 27.7
8 5/16 05 U2000-05 24.0 30.5
10 3/8 06 U2000-06 26.0 31.7
12 1/2 08 U2000-08 30.0 34.5
16 5/8 10 U2000-10 34.0 36.5
19 3/4 12 U2000-12 38.0 40.5
25 1 16 U2000-16 46.0 53.0
31 1-1/4 20 U2000-20 57.0 59.0
38 1-1/2 24 U2000-24 - -
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
59
CRIMPED FERRULE FOR USE ON THERMOPLASTIC HOSE
FERR
ULES
NON-SKIVED CRIMPED FERRULE
NOMINAL HOSE BOREmm in dash PART NUMBER Dim A Dim B
5 3/16 03 U7000-03 14.5 25.4
6 1/4 04 U7000-04 16.6 32.5
8 5/16 05 U7000-05 20.0 30.5
10 3/8 06 U7000-06 21.0 32.0
12 1/2 08 U7000-08 24.6 36.6
19 3/4 12 U7000-12 30.1 44.5
25 1 16 U7000-16 37.3 53.1
NOMINAL HOSE BOREmm in dash PART NUMBER Dim A Dim B
5 3/16 03 U5000-03 20.0 21.0
6 1/4 04 U5000-04 23.0 29.6
8 5/16 05 U5000-05 24.0 30.5
10 3/8 06 U5000-06 26.0 31.2
12 1/2 08 U5000-08 29.7 33.5
16 5/8 10 U5000-10 33.0 36.0
19 3/4 12 U5000-12 37.0 40.0
25 1 16 U5000-16 47.0 50.0
31 1-1/4 20 U5000-20 59.0 57.0
38 1-1/2 24 U5000-24 – –
51 2 32 U5000-32 79.9 71.0
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
60
CRIMPED FERRULE FOR USE ON THERMOPLASTIC HOSE
CRIMPED FERRULE FOR USE ON THERMOPLASTIC HOSE
FERRULES
See page 58 for how to order one-piece hose ends
NOMINAL HOSE BOREmm in dash PART NUMBER Dim A Dim B
6 1/4 04 U8000-04 20.6 30.2
8 5/16 05 U8000-05 20.4 30.2
10 3/8 06 U8000-06 23.0 33.3
12 1/2 08 U8000-08 26.2 36.5
16 5/8 10 U8000-10 29.4 38.9
19 3/4 12 U8000-12 33.3 44.5
NOMINAL HOSE BOREmm in dash PART NUMBER Dim A Dim B
5 3/16 03 U9000-03 16.0 27.6
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies*Only available in ‘B’ & ‘C’ one piece range
61
See page 58 for how to order one-piece hose ends
J.I.C. MALE
JIC
Assembly Component B9
7/16" x 20 04 5 3/16 03 U04JM03 14.3 27.7 14.0 2.8
7/16" x 20 04 6 1/4 04 U04JM04 13.0 28.2 14.0 4.0
1/2" x 20 05 6 1/4 04 U05JM04 13.0 29.2 14.0 4.0
9/16" x 18 06 6 1/4 04 U06JM04 16.0 29.2 14.0 4.0
3/4" x 16 08 8 5/16 05 U08JM05* 19.0 34.0 16.5 5.5
7/16" x 20 04 10 3/8 06 U04JM06 15.9 29.7 14.0 7.0
1/2" x 20 05 10 3/8 06 U05JM06 17.0 29.7 14.0 5.5
9/16" x 18 06 10 3/8 06 U06JM06 16.0 29.7 14.0 7.0
3/4" x 16 08 10 3/8 06 U08JM06 19.0 34.5 16.5 7.0
9/16" x 18 06 12 1/2 08 U06JM08 19.0 32.3 14.0 9.3
3/4" x 16 08 12 1/2 08 U08JM08 22.0 34.8 16.5 9.3
7/8" x 14 10 12 1/2 08 U10JM08 24.0 39.3 19.5 9.3
3/4" x 16 08 16 5/8 10 U08JM10 22.2 34.9 16.5 12.0
7/8" x 14 10 16 5/8 10 U10JM10 24.0 39.4 19.5 12.0
1-1/16" x 12 12 16 5/8 10 U12JM10 27.0 43.2 22.0 12.0
7/8" x 14 10 19 3/4 12 U10JM12 27.0 40.3 19.5 15.0
1-1/16" x 12 12 19 3/4 12 U12JM12 27.0 44.1 22.0 15.0
1-5/16" x 12 16 19 3/4 12 U16JM12 36.0 47.1 23.0 15.0
1-1/16" x 12 12 25 1 16 U12JM16 31.8 47.1 22.0 19.5
1-5/16" x 12 16 25 1 16 U16JM16 36.0 48.1 23.0 19.5
1-5/8" x 12 20 25 1 16 U20JM16 46.0 53.3 24.3 19.5
1-5/16" x 12 16 31 1-1/4 20 U16JM20 41.3 52.3 23.0 26.0
1-5/8" x 12 20 31 1-1/4 20 U20JM20 46.0 53.5 24.3 26.0
1-5/8" x 12 20 38 1-1/2 24 U20JM24 44.4 53.7 24.3 32.0
2-1/2" x 12 32 51 2 32 U32JM32 65.0 72.1 34.0 44.0
NOMINAL HOSE BOREJIC THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
62
See page 16 for how to order hose assemblies
J.I.C. FEMALE Assembly Component C1LOOSE NUT
1/2" x 20 05 5 3/16 03 U05JF03* 17 14.5 9.5 2.8
1/2" x 20 05 6 1/4 04 U05JF04 17 15.0 9.5 4.0
9/16" x 18 06 6 1/4 04 U06JF04 19 16.0 8.7 4.0
3/4" x 16 08 8 5/16 05 U08JF05* 22 17.6 10.7 5.5
3/4" x 16 08 10 3/8 06 U08JF06 22 18.1 10.7 7.0
7/8" x 14 10 10 3/8 06 U10JF06 27 19.5 13.7 7.0
7/8" x 14 10 12 1/2 08 U10JF08 27 19.8 13.7 9.3
1-1/16" x 12 12 12 1/2 08 U12JF08 32 21.7 15.0 9.3
1-1/16" x 12 12 16 5/8 10 U12JF10 32 21.8 15.0 12.0
NOMINAL HOSE BOREJIC THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim CJIC
*Only available in ‘B’ & ‘C’ one piece rangeSee page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
63
See page 16 for how to order hose assemblies
J.I.C. FEMALE Assembly Component C1WIRED ON NUT
NOMINAL HOSE BOREJIC THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
JIC
*Only available in ‘B’ & ‘C’ one piece rangeSee page 58 for how to order one-piece hose ends
7/16" x 20 04 5 3/16 03 U04JF03* 14 15.0 8.4 2.8
7/16" x 20 04 6 1/4 04 U04JF04 14 15.5 8.4 4.0
1/2" x 20 05 8 5/16 05 U05JF05* 17 16.0 9.5 5.5
9/16" x 18 06 8 5/16 05 U06JF05* 19 15.7 8.7 5.5
7/16" x 20 04 10 3/8 06 U04JF06 14 16.0 8.4 7.0
1/2" x 20 05 10 3/8 06 U05JF06 17 16.5 9.5 4.0
9/16" x 18 06 10 3/8 06 U06JF06 19 16.2 8.7 7.0
9/16" x 18 06 12 1/2 08 U06JF08 19 16.5 8.7 9.3
3/4" x 16 08 12 1/2 08 U08JF08 22 17.6 10.7 9.3
3/4" x 16 08 16 5/8 10 U08JF10 22 18.2 10.7 12.0
7/8" x 14 10 16 5/8 10 U10JF10 27 19.7 13.7 12.0
1-3/16" x 12 14 19 3/4 12 U10JF12 36 22.3 14.7 15.0
1-1/16" x 12 12 19 3/4 12 U12JF12 32 21.8 15.0 15.0
1-5/16" x 12 16 19 3/4 12 U16JF12 41 23.1 16.8 15.0
1-1/16" x 12 12 25 1 16 U12JF16 32 23.8 15.0 15.0
1-5/16" x 12 16 25 1 16 U16JF16 41 24.1 16.8 19.5
1-5/8" x 12 20 25 1 16 U20JF16 50 28.7 16.1 19.5
1-5/16" x 12 16 31 1-1/4 20 U16JF20 41 24.4 16.8 26.0
1-5/8" x 12 20 31 1-1/4 20 U20JF20 50 28.5 16.1 26.0
1-7/8" x 12 24 31 1-1/4 20 U24JF20 60 29.7 19.4 26.0
1-5/8" x 12 20 38 1-1/2 24 U20JF24 50 28.7 16.1 32.0
1-7/8" x 12 24 38 1-1/2 24 U24JF24 60 30.8 19.4 32.0
1-7/8" x 12 24 51 2 32 U24JF32 60 33.1 19.4 44.0
2-1/2" x 12 32 51 2 32 U32JF32 75 33.4 24.2 44.0
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
64
See page 16 for how to order hose assemblies
JIC
J.I.C. FEMALE 90° SWEPT ELBOW Assembly Component C3LOOSE NUT
See page 58 for how to order one-piece hose ends
1/2" x 20 05 6 1/4 04 U05JF90S04 17 27.2 27.2 9.5 4.0
9/16" x 18 06 6 1/4 04 U06JF90S04 19 27.2 28.2 8.7 4.0
3/4" x 16 08 10 3/8 06 U08JF90S06 22 31.5 32.3 10.7 7.0
7/8" x 14 10 12 1/2 08 U10JF90S08 27 42.3 39.2 13.7 9.3
1-1/16" x 12 12 12 1/2 08 U12JF90S08 32 42.3 42.6 15.0 9.3
1-1/16" x 12 12 16 5/8 10 U12JF90S10 32 47.6 51.8 15.0 12.0
NOMINAL HOSE BOREJIC THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
65
See page 16 for how to order hose assemblies
JIC
J.I.C. FEMALE 90° SWEPT ELBOW WIRED ON NUT
Assembly Component C3
NOMINAL HOSE BOREJIC THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
*Only available in ‘B’ & ‘C’ one piece rangeSee page 58 for how to order one-piece hose ends
7/16" x 20 04 5 3/16 03 U04JF90S03* 14 24.3 29.4 8.4 2.8
7/16" x 20 04 6 1/4 04 U04JF90S04 14 27.2 32.4 8.4 4.0
1/2" x 20 05 8 5/16 05 U05JF90S05* 17 28.7 33.0 9.5 5.5
9/16" x 18 06 8 5/16 05 U06JF90S05* 19 28.7 32.7 8.7 5.5
7/16" x 20 04 10 3/8 06 U04JF90S06 14 31.5 35.1 8.4 7.0
9/16" x 18 06 10 3/8 06 U06JF90S06 19 31.5 35.3 8.7 7.0
9/16" x 18 06 12 1/2 08 U06JF90S08 19 42.3 39.9 8.7 9.3
3/4" x 16 08 12 1/2 08 U08JF90S08 22 42.3 41.0 10.7 9.3
3/4" x 16 08 16 5/8 10 U08JF90S10 22 47.6 50.3 10.7 12.0
7/8" x 14 10 16 5/8 10 U10JF90S10 27 47.6 51.8 13.7 12.0
1-1/16" x 12 12 19 3/4 12 U12JF90S12 32 53.8 61.0 15.0 15.0
1-5/16" x 12 16 19 3/4 12 U16JF90S12 41 53.8 63.1 16.8 15.0
1-5/16" x 12 16 25 1 16 U16JF90S16 41 63.8 75.1 16.8 19.5
1-5/8" x 12 20 25 1 16 U20JF90S16 50 63.8 78.0 16.1 19.5
1-5/8" x 12 20 31 1-1/4 20 U20JF90S20 50 81.0 91.1 16.1 26.0
1-7/8" x 12 24 31 1-1/4 20 U24JF90S20 60 81.0 90.5 19.4 26.0
1-7/8" x 12 24 38 1-1/2 24 U24JF90S24 60 106.4 109.2 19.4 32.0
2-1/2" x 12 32 51 2 32 U32JF90S32 75 136.1 147.2 24.2 –
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
66
See page 16 for how to order hose assemblies
J.I.C. FEMALE 45° SWEPT ELBOW
JIC
Assembly Component C5
*Only available in ‘B’ & ‘C’ one piece range
WIRED ON NUT
See page 58 for how to order one-piece hose ends
J.I.C. FEMALE 45° SWEPT ELBOW
LOOSE NUT
Assembly Component C5
1/2" x 20 05 6 1/4 04 U05JF45S04 17 32.4 13.4 9.5 4.0
9/16" x 18 06 6 1/4 04 U06JF45S04 19 33.1 14.1 8.7 4.0
3/4" x 16 08 10 3/8 06 U08JF45S06 22 37.8 16.0 10.7 7.0
7/8" x 14 10 12 1/2 08 U10JF45S08 27 49.2 19.2 13.7 9.3
1-1/16" x 12 12 16 5/8 10 U12JF45S10 32 57.2 25.4 15.0 12.0
NOMINAL HOSE BOREJIC THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
7/16" x 20 04 6 1/4 04 U04JF45S04 14 36.1 17.1 8.4 4.0
9/16" x 18 06 8 5/16 05 U06JF45S05* 19 36.8 16.9 8.7 5.5
7/16" x 20 04 10 3/8 06 U04JF45S06 14 39.8 18.0 8.4 7.0
9/16" x 18 06 10 3/8 06 U06JF45S06 19 40.0 18.1 8.7 7.0
9/16" x 18 06 12 1/2 08 U06JF45S08 19 49.5 19.5 8.7 9.3
3/4" x 16 08 12 1/2 08 U08JF45S08 22 50.3 20.3 10.7 9.3
3/4" x 16 08 16 5/8 10 U08JF45S10 22 56.2 24.4 10.7 12.0
7/8" x 14 10 16 5/8 10 U10JF45S10 27 57.2 25.4 13.7 12.0
1-1/16" x 12 12 19 3/4 12 U12JF45S12 32 65.1 30.0 15.0 15.0
1-5/16" x 12 16 25 1 16 U16JF45S16 41 77.9 37.0 16.8 19.5
1-5/8" x 12 20 25 1 16 U20JF45S16 50 79.9 39.0 16.1 19.5
1-5/8" x 12 20 31 1-1/4 20 U20JF45S20 50 97.4 44.5 16.1 26.0
1-7/8" x 12 24 31 1-1/4 20 U24JF45S20 60 97.0 44.1 19.4 26.0
1-7/8" x 12 24 38 1-1/2 24 U24JF45S24 60 122.0 51.7 19.4 32.0
NOMINAL HOSE BOREJIC THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
67
See page 16 for how to order hose assemblies
J.I.C. 90° COMPACT FEMALE
J.I.C. FEMALE EQUAL HEXAGON WIRED ON NUT
JIC
Assembly Component C6
Assembly Component K8
WIRED ON NUT
7/16" x 20 04 6 1/4 04 U04JF90K04 14 17.3 18.8 8.4 4.0
9/16" x 18 06 6 1/4 04 U06JF90K04 19 17.3 21.6 8.7 4.0
9/16" x 18 06 10 3/8 06 U06JF90K06 19 17.8 21.6 8.7 7.0
3/4" x 16 08 10 3/8 06 U08JF90K06 22 20.9 26.2 10.7 7.0
3/4" x 16 08 12 1/2 08 U08JF90K08 22 21.2 26.2 10.7 9.3
NOMINAL HOSE BOREJIC THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
7/16" x 20 04 6 1/4 04 U04HJF04 14 14 20.3 8.4 4.0
9/16" x 18 06 6 1/4 04 U06HJF04 19 19 22.1 8.7 4.0
9/16" x 18 06 10 3/8 06 U06HJF06 19 19 23.1 8.7 7.0
3/4" x 16 08 12 1/2 08 U08HJF08 22 22 25.0 10.7 9.3
7/8" x 14 10 12 1/2 08 U10HJF08 27 27 28.2 13.7 9.3
1-1/16" x 12 12 19 3/4 12 U12HJF12 32 32 32.0 15.0 15.0
1-5/16" x 12 16 25 1 16 U16HJF16 41 41 36.3 16.8 19.5
1-5/8" x 12 20 31 1-1/4 20 U20HJF20 50 50 45.3 16.1 26.0
NOMINAL HOSE BOREJIC THREAD DASH No. mm in dash PART NUMBER A/F1 A/F2 Dim A Dim B Dim C
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
68
See page 16 for how to order hose assemblies
N.P.T.F. MALE Assembly Component H3
See page 58 for how to order one-piece hose ends
NPTF/NPSM
1/8" x 27 02 5 3/16 03 U02NM03* 12 23.2 9.5 2.8
1/4" x 18 04 5 3/16 03 U04NM03* 14 29.2 14.5 2.8
1/8" x 27 02 6 1/4 04 U02NM04 13 23.7 9.5 4.0
1/4" x 18 04 6 1/4 04 U04NM04 14 29.7 14.5 4.0
3/8" x 18 06 6 1/4 04 U06NM04 19 32.0 14.5 4.0
3/8" x 18 06 8 5/16 05 U06NM05* 19 32.0 14.5 5.5
1/4" x 18 04 10 3/8 06 U04NM06 17 30.2 14.5 7.0
3/8" x 18 06 10 3/8 06 U06NM06 19 32.5 14.5 7.0
1/2" x 14 08 10 3/8 06 U08NM06 24 38.8 19.3 7.0
3/8" x 18 06 12 1/2 08 U06NM08 22 32.5 14.5 9.3
1/2" x 14 08 12 1/2 08 U08NM08 24 39.1 19.3 9.3
1/2" x 14 08 16 5/8 10 U08NM10 24 39.2 19.3 12.0
3/4" x 14 12 16 5/8 10 U12NM10 27 40.5 19.3 12.0
3/4" x 14 12 19 3/4 12 U12NM12 27 41.4 19.3 15.0
1" x 11.5 16 25 1 16 U16NM16 36 46.9 23.8 19.5
1-1/4" x 11.5 20 31 1-1/4 20 U20NM20 46 56.5 24.6 26.0
1-1/2" x 11.5 24 38 1-1/2 24 U24NM24 50 53.8 25.4 32.0
2" x 11.5 32 51 2 32 U32NM32 65 64.0 26.2 –
N/P.T.F. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
*Only available in ‘B’ & ‘C’ one piece range
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
69
See page 16 for how to order hose assemblies See page 58 for how to order one-piece hose ends
N.P.S.M. FEMALE
N.P.S.M. FEMALE Assembly Component H1
Assembly Component H1WIRED ON NUT Airless paint spray
LOOSE NUT Airless paint spray
NPTF
/NPS
M
1/4" 04 5 3/16 03 U04NSF03* 19 16.0 4.2 2.8
1/4" 04 8 1/4 04 U04NSF04 19 16.5 4.2 4.0
3/8" 06 10 3/8 06 U06NSF06 22 19.6 5.3 7.0
1/2" 08 12 1/2 08 U08NSF08 27 20.8 6.4 9.3
3/4" 12 19 3/4 12 U12NSF12 – – – –
NPSM THREAD SIZE NOMINAL HOSE BOREin DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
1/4" 04 10 3/8 06 U04NSF06 19 18.7 5.2 4.0
NPSM THREAD SIZE NOMINAL HOSE BOREin DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
N.P.T.F. SWIVEL MALE Assembly Component H4
1/4" x 18 04 6 1/4 04 U04NMS04 17 38.3 14.5 4.0
1/4" x 18 04 10 3/8 06 U04NMS06 17 38.8 14.5 4.0
3/8" x 18 06 10 3/8 06 U06NMS06 22 39.2 14.5 7.0
1/2" x 14 08 12 1/2 08 U08NMS08 27 46.2 19.3 9.3
3/4" x 14 12 19 3/4 12 U12NMS12 32 48.5 19.3 15.0
1" x 11.5 16 25 1 16 U16NMS16 38 57.7 23.8 19.5
N/P.T.F. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
70
See page 16 for how to order hose assemblies
O.R.F.S FEMALE
O.R.F.S MALE Assembly Component K9
Assembly Component J5WITH DOUBLE HEXAGON
See page 58 for how to order one-piece hose ends
ORFS
9/16" x 18 04 6 1/4 04 U04ORM04 17 24.4 9.9 4.0
11/16" x 16 06 10 3/8 06 U06ORM06 19 26.3 11.2 6.6
13/16" x 16 08 12 1/2 08 U08ORM08 22 29.2 12.8 9.3
1-3/16" x 12 12 19 3/4 12 U12ORM12 32 38.4 17.0 15.0
1-7/16" x 12 16 25 1 16 U16ORM16 41 43.7 17.5 19.5
NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
9/16" x 18 04 6 1/4 04 U04ORF04 17 14 27.1 8.2 4.0
11/16" x 16 06 6 1/4 04 U06ORF04 22 17 30.5 9.5 4.0
11/16" x 16 06 10 3/8 06 U06ORF06 22 17 31.5 9.5 7.0
13/16" x 16 08 10 3/8 06 U08ORF06 24 19 34.7 11.0 7.0
13/16" x 16 08 12 1/2 08 U08ORF08 24 22 35.0 11.0 9.3
1" x 14 10 16 5/8 10 U10ORF10 30 24 40.2 13.5 12.0
1-3/16" x 12 12 19 3/4 12 U12ORF12 36 30 44.6 14.5 15.0
1-7/16" x 12 16 25 1 16 U16ORF16 41 36 48.1 14.8 19.5
1-11/16" x 12 20 31 1-1/4 20 U20ORF20 50 41 52.6 14.5 26.0
2" x 12 24 38 1-1/2 24 U24ORF24 60 50 61.7 14.5 32.0
NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F 1 A/F 2 Dim A Dim B Dim C
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
71
See page 16 for how to order hose assemblies
ORFS
*Only available in ‘B’ & ‘C’ one piece rangeSee page 58 for how to order one-piece hose ends
O.R.F.S FEMALE 90° SWEPT ELBOW Assembly Component J7
9/16" x 18 04 6 1/4 04 U04ORF90S04 17 27.2 32.0 8.2 4.0
11/16" x 16 06 6 1/4 04 U06ORF90S04 22 27.2 32.0 9.5 4.0
11/16" x 16 06 8 5/16 05 U06ORF90S05* 22 28.7 38.0 9.5 5.5
11/16" x 16 06 10 3/8 06 U06ORF90S06 22 31.5 38.0 9.5 7.0
13/16" x 16 08 10 3/8 06 U08ORF90S06 24 31.5 41.0 11.0 7.0
13/16" x 16 08 12 1/2 08 U08ORF90S08 24 42.3 41.0 11.0 9.3
1" x 14 10 12 1/2 08 U10ORF90S08 30 42.3 41.0 13.5 9.3
1" x 14 10 16 5/8 10 U10ORF90S10 30 47.6 47.0 13.5 12.0
1-3/16" x 12 12 19 3/4 12 U12ORF90S12 36 53.8 58.0 14.5 15.0
1-7/16" x 12 16 19 3/4 12 U16ORF90S12 41 53.8 58.0 14.8 15.0
1-7/16" x 12 16 25 1 16 U16ORF90S16 41 63.8 71.0 14.8 19.5
1-11/16" x 12 20 31 1-1/4 20 U20ORF90S20 50 81.0 78.0 14.5 26.0
2" x 12 24 38 1-1/2 24 U24ORF90S24 60 106.4 87.0 14.5 32.0
NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
72
See page 16 for how to order hose assemblies
O.R.F.S FEMALE 90° SWEPT ELBOW
O.R.F.S FEMALE 45° SWEPT ELBOW
ORFS
Assembly Component J9
Assembly Component K2
*Only available in ‘B’ & ‘C’ one piece range
LONG DROP
9/16" x 18 04 6 1/4 04 U04ORF45S04 17 29.0 10.0 8.2 4.0
11/16" x 16 06 6 1/4 04 U06ORF45S04 22 – – 9.5 4.0
11/16" x 16 06 8 5/16 05 U06ORF45S05* 22 – – 9.5 5.5
11/16" x 16 06 10 3/8 06 U06ORF45S06 22 33.3 11.5 9.5 7.0
13/16" x 16 08 10 3/8 06 U08ORF45S06 24 – – 11.0 7.0
13/16" x 16 08 12 1/2 08 U08ORF45S08 24 45.0 15.0 11.0 9.3
1" x 14 10 12 1/2 08 U10ORF45S08 30 46.0 16.0 13.5 9.3
1" x 14 10 16 5/8 10 U10ORF45S10 30 – – 13.5 12.0
1-3/16" x 12 12 19 3/4 12 U12ORF45S12 36 56.2 21.0 14.5 15.0
1-7/16" x 12 16 25 1 16 U16ORF45S16 41 – – 14.8 19.5
1-11/16" x 12 20 31 1-1/4 20 U20ORF45S20 50 – – 14.5 26.0
2" x 12 24 38 1-1/2 24 U24ORF45S24 60 – – 14.5 32.0
NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
9/16" x 18 04 6 1/4 04 U04ORF90SL04 17 27.2 46.0 8.2 4.0
11/16" x 16 06 10 3/8 06 U06ORF90SL06 22 31.5 54.0 9.5 7.0
13/16" x 16 08 12 1/2 08 U08ORF90SL08 24 42.3 64.0 11.0 9.3
1" x 14 10 16 5/8 10 U10ORF90SL10 30 47.6 70.0 13.5 12.0
1-3/16" x 12 12 19 3/4 12 U12ORF90SL12 36 53.8 96.0 14.5 15.0
1-7/16" x 12 16 25 1 16 U16ORF90SL16 41 63.8 114.0 14.8 19.5
NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
73
See page 16 for how to order hose assemblies
S.A.E. / I.S.O. FLANGE STRAIGHT INSERT Assembly Component H6CODE 61
SAE
13 1/2 8 12 1/2 08 U08SFH308 46.0 30.2 9.3
19 3/4 12 12 1/2 08 U12SFH308 47.8 38.1 9.3
19 3/4 12 16 5/8 10 U12SFH310 47.9 38.1 12.0
19 3/4 12 19 3/4 12 U12SFH312 47.5 38.1 15.0
19 3/4 16 19 3/4 12 U16SFH312 65.6 44.5 15.0
25 1 16 25 1 16 U16SFH316 66.4 44.5 19.5
32 1-1/4 20 25 1 16 U20SFH316 72.1 50.8 19.5
32 1-1/4 20 31 1-1/4 20 U20SFH320 71.2 50.8 26.0
38 1-1/2 24 38 1-1/2 24 U24SFH324 77.9 60.4 32.0
38 1-1/2 32 38 1-1/2 24 U32SFH324 75.4 71.4 32.0
51 2 32 51 2 32 U32SFH332 78.7 71.4 –
NOMINAL FLANGE SIZE NOMINAL HOSE BORE
mm in dash mm in dash PART NUMBER Dim A Dim B Dim C
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
74
See page 16 for how to order hose assemblies
S.A.E. / I.S.O. FLANGE 90° SWEPT ELBOW Assembly Component H8CODE 61SAE
13 1/2 8 12 1/2 08 U08SFH90S308 42.3 42.0 30.2 9.3
19 3/4 12 16 5/8 10 U12SFH90S310 – – 38.1 12.0
19 3/4 12 19 3/4 12 U12SFH90S312 58.0 58.0 38.1 15.0
25 1 16 25 1 16 U16SFH90S316 63.8 70.0 44.5 19.5
32 1-1/4 20 25 1 16 U20SFH90S316 63.8 70.0 50.8 19.5
32 1-1/4 20 31 1-1/4 20 U20SFH90S320 81.0 90.0 50.8 26.0
38 1-1/2 24 31 1-1/4 20 U24SFH90S320 – – 60.4 26.0
32 1-1/4 20 38 1-1/2 24 U20SFH90S324 – 90.0 50.8 32.0
38 1-1/2 24 38 1-1/2 24 U24SFH90S324 – 104.0 60.4 32.0
51 2 32 38 1-1/2 24 U32SFH90S324 – – 71.4 32.0
51 2 32 51 2 32 U32SFH90S332 – – 71.4 –
NOMINAL FLANGE SIZE NOMINAL HOSE BORE
mm in dash mm in dash PART NUMBER Dim A Dim B Dim C Dim D
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
75
See page 16 for how to order hose assemblies
SAE
S.A.E. / I.S.O. FLANGE 45° SWEPT ELBOW
S.A.E. / I.S.O. SPLIT FLANGE CLAMPS
CODE 61
Assembly Component H9
See page 58 for how to order one-piece hose ends
CODE 61
13 1/2 8 12 1/2 08 U08SFH45S308 – – 30.2 9.3
19 3/4 12 12 1/2 08 U12SFH45S308 – – 38.1 9.3
19 3/4 12 19 3/4 12 U12SFH45S312 67.3 27.9 38.1 15.0
25 1 16 25 1 16 U16SFH45S316 74.3 33.3 44.5 19.5
32 1-1/4 20 25 1 16 U20SFH45S316 – – 50.8 19.5
25 1 16 31 1-1/4 20 U16SFH45S320 – – 44.5 26.0
32 1-1/4 20 31 1-1/4 20 U20SFH45S320 – – 50.8 26.0
38 1-1/2 24 38 1-1/2 24 U24SFH45S324 – – 60.4 32.0
51 2 32 38 1-1/2 24 U32SFH45S324 – – 71.4 32.0
51 2 32 51 2 32 U32SFH45S332 – – 71.4 –
NOMINAL FLANGE SIZE NOMINAL HOSE BORE
mm in dash mm in dash PART NUMBER Dim A Dim B Dim C Dim D
13 1/2 08 RU08SFC3 – – – – – – 9.0 –
19 3/4 12 RU12SFC3 – – – – – – 11.0 –
25 1 16 RU16SFC3 – – – – – – 11.0 –
32 1-1/4 20 RU20SFC3 – – – – – – 12.0 –
38 1-1/2 24 RU24SFC3 – – – – – – 13.5 –
51 2 32 RU32SFC3 – – – – – – 13.5 –
NOMINAL FLANGE SIZE
mm in dash PART NUMBER Dim A Dim B Dim C Dim D Dim E Dim F Dim G Dim H
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
76
See page 16 for how to order hose assemblies
S.A.E. / I.S.O. FLANGE 90° SWEPT ELBOW
S.A.E. / I.S.O. FLANGE STRAIGHT INSERT Assembly Component L1
Assembly Component L2CODE 62
CODE 62SAE
13 1/2 8 12 1/2 08 U08SFH608 46.8 31.8 9.3
19 3/4 12 19 3/4 12 U12SFH612 50.7 41.3 15.0
25 1 16 19 3/4 12 U16SFH612 70.0 47.6 15.0
25 1 16 25 1 16 U16SFH616 71.4 47.6 19.5
32 1-1/4 20 25 1 16 U20SFH616 79.9 54.0 19.5
32 1-1/4 20 31 1-1/4 20 U20SFH620 79.8 54.0 26.0
38 1-1/2 24 31 1-1/4 20 U24SFH620 90.5 63.5 26.0
38 1-1/2 24 38 1-1/2 24 U24SFH624 91.2 63.5 32.0
51 2 32 51 2 32 U32SFH632 98.4 79.4 –
NOMINAL FLANGE SIZE NOMINAL HOSE BORE
mm in dash mm in dash PART NUMBER Dim A Dim B Dim C
13 1/2 8 12 1/2 08 U08SFH90S608 – – 31.8 9.3
19 3/4 12 16 5/8 10 U12SFH90S610 – – 41.3 12.0
19 3/4 12 19 3/4 12 U12SFH90S612 58.0 61.0 41.3 15.0
25 1 16 19 3/4 12 U16SFH90S612 58.0 70.0 47.6 15.0
25 1 16 25 1 16 U16SFH90S616 63.8 70.0 47.6 19.5
32 1-1/4 20 25 1 16 U20SFH90S616 63.8 70.0 54.0 19.5
32 1-1/4 20 31 1-1/4 20 U20SFH90S620 81.0 90.0 54.0 26.0
38 1-1/2 24 31 1-1/4 20 U24SFH90S620 – – 63.5 26.0
38 1-1/2 24 38 1-1/2 24 U24SFH90S624 – 104.0 63.5 32.0
51 2 32 51 2 32 U32SFH90S632 – – 79.4 –
NOMINAL FLANGE SIZE NOMINAL HOSE BORE
mm in dash mm in dash PART NUMBER Dim A Dim B Dim C Dim D
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
77
See page 16 for how to order hose assemblies
S.A.E. / I.S.O. FLANGE 45° SWEPT ELBOW
S.A.E. / I.S.O. SPLIT FLANGE CLAMPS
SAE
Assembly Component L3
CODE 62
CODE 62
13 1/2 8 12 1/2 08 U08SFH45S608 – – 31.8 9.3
19 3/4 12 16 5/8 10 U12SFH45S610 – – 41.3 12.0
19 3/4 12 19 3/4 12 U12SFH45S612 – – 41.3 15.0
25 1 16 19 3/4 12 U16SFH45S612 73.2 33.8 47.6 15.0
25 1 16 25 1 16 U16SFH45S616 – – 47.6 19.5
32 1-1/4 20 25 1 16 U20SFH45S616 – – 54.0 19.5
32 1-1/4 20 31 1-1/4 20 U20SFH45S620 – – 54.0 26.0
38 1-1/2 24 31 1-1/4 20 U24SFH45S620 – – 63.5 26.0
38 1-1/2 24 38 1-1/2 24 U24SFH45S624 – – 63.5 32.0
51 2 32 51 2 32 U32SFH45S632 – – 79.4 –
NOMINAL FLANGE SIZE NOMINAL HOSE BORE
mm in dash mm in dash PART NUMBER Dim A Dim B Dim C Dim D
13 1/2 08 RU08SFC6 – – – – – – 9.0 –
19 3/4 12 RU12SFC6 – – – – – – 11.0 –
25 1 16 RU16SFC6 – – – – – – 13.0 –
32 1-1/4 20 RU20SFC6 – – – – – – 15.0 –
38 1-1/2 24 RU24SFC6 – – – – – – 17.0 –
51 2 32 RU32SFC6 – – – – – – 21.0 –
NOMINAL FLANGE SIZE
mm in dash PART NUMBER Dim A Dim B Dim C Dim D Dim E Dim F Dim G Dim H
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
78
See page 16 for How to order hose assemblies
SAE
S.A.E. “O” RING MALE Assembly Component C9
7/16" x 20 04 6 1/4 04 U04SMR04 14.3 24.3 9.1 4.0
9/16" x 18 06 10 3/8 06 U06SMR06 17.5 25.7 10.0 7.0
3/4" x 16 08 12 1/2 08 U08SMR08 22.2 30.9 11.1 9.3
7/8" x 14 10 12 1/2 08 U10SMR08 27.0 28.7 12.7 9.3
3/4" x 16 08 16 5/8 10 U08SMR10 22.2 31.0 11.1 12.0
7/8" x 14 10 16 5/8 10 U10SMR10 27.0 32.6 12.7 12.0
1-1/16" x 12 12 19 3/4 12 U12SMR12 31.8 39.2 15.1 15.0
1-5/16" x 12 16 25 1 16 U16SMR16 41.3 41.7 15.1 19.5
1-5/8" x 12 20 31 1-1/4 20 U20SMR20 50.8 47.0 15.1 26.0
NOMINAL HOSE BORESAE THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
S.A.E. SWIVEL MALE Assembly Component D1
7/16" x 20 04 6 1/4 04 U04SMRS04 17.5 34.7 9.1 4.0
9/16" x 18 06 10 3/8 06 U06SMRS06 20.6 36.7 10.0 7.0
3/4" x 16 08 12 1/2 08 U08SMRS08 28.7 41.6 11.1 9.3
1-1/16" x 12 12 19 3/4 12 U12SMRS12 31.8 47.0 15.1 15.0
NOMINAL HOSE BORESAE THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
79
See page 16 for how to order hose assemblies
METRIC MALE - DKO 'S' HEAVY DUTY
Assembly Component D3Assembly Component D3
MET
RIC
M16 x 1.5 8 6 1/4 04 U16ME0804 17 24.4 12.0 4.0
M18 x 1.5 10 6 1/4 04 U18ME1004 19 24.7 12.0 4.0
M20 x 1.5 12 8 5/16 05 U20ME1205* 22 25.7 12.0 5.5
M18 x 1.5 10 10 3/8 06 U18ME1006 19 25.7 12.0 7.0
M20 x 1.5 12 10 3/8 06 U20ME1206 22 26.2 12.0 7.0
M22 x 1.5 14 10 3/8 06 U22ME1406 22 28.2 14.0 7.0
M22 x 1.5 14 12 1/2 08 U22ME1408 22 28.5 14.0 9.3
M24 x 1.5 16 12 1/2 08 U24ME1608 24 29.7 14.0 9.3
M30 x 2.0 20 16 5/8 10 U30ME2010 30 33.4 16.0 12.0
M30 x 2.0 20 19 3/4 12 U30ME2012 30 34.3 16.0 15.0
M36 x 2.0 25 19 3/4 12 U36ME2512 36 38.0 18.0 15.0
M42 x 2.0 30 25 1 16 U42ME3016 46 46.9 20.0 19.5
M52 x 2.0 38 31 1-1/4 20 U52ME3820 55 49.8 22.0 26.0
METRIC NOMINAL HOSE BORETHREAD TUBE SIZE mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
*Only available in ‘B’ & ‘C’ one piece rangeSee page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
80
See page 16 for how to order hose assemblies
METRIC MALE - DKO 'L' Assembly Component D4
*Only available in ‘B’ & ‘C’ one piece range
Assembly Component D4LIGHT DUTY
See page 58 for how to order one-piece hose ends
METRIC
M12 x 1.5 6 6 1/4 04 U12ME0604 14 21.1 10.0 4.0
M14 x 1.5 8 6 1/4 04 U14ME0804 14 21.1 10.0 4.0
M16 x 1.5 10 6 1/4 04 U16ME1004 17 23.4 11.0 4.0
M18 x 1.5 12 8 5/16 05 U18ME1205* 19 24.2 11.0 5.5
M16 x 1.5 10 10 3/8 06 U16ME1006 17 24.4 11.0 7.0
M18 x 1.5 12 10 3/8 06 U18ME1206 19 24.7 11.0 7.0
M22 X 1.5 15 10 3/8 06 U22ME1506 22 26.2 12.0 7.0
M22 X 1.5 15 12 1/2 08 U22ME1508 22 26.5 12.0 9.3
M26 x 1.5 18 12 1/2 08 U26ME1808 27 28.2 12.0 9.3
M26 x 1.5 18 16 5/8 10 U26ME1810 27 28.3 12.0 12.0
M30 x 2.0 22 19 3/4 12 U30ME2212 30 32.3 14.0 15.0
M36 x 2.0 28 25 1 16 U36ME2816 36 35.0 14.0 19.5
M45 x 2.0 35 31 1-1/4 20 U45ME3520 46 43.3 16.0 26.0
METRIC NOMINAL HOSE BORETHREAD TUBE SIZE mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
81
See page 16 for how to order hose assemblies See page 58 for how to order one-piece hose ends
METRIC LOOSE NUT FEMALE - DKO 'S' Assembly Component E8Assembly Component E8HEAVY DUTY
M14 x 1.5 6 1/4 04 U14MSOF0604 17 26.0 3.5 2.8
M16 x 1.5 6 1/4 04 U16MSOF0804 19 26.2 2.8 4.0
M18 x 1.5 6 1/4 04 U18MSOF1004 22 27.2 3.6 4.0
M20 x 1.5 8 5/16 05 U20MSOF1205* 24 27.3 3.6 5.5
M18 x 1.5 10 3/8 06 U18MSOF1006 22 27.7 3.6 4.6
M20 x 1.5 10 3/8 06 U20MSOF1206 24 27.8 3.6 7.0
M22 x 1.5 10 3/8 06 U22MSOF1406 27 31.5 3.6 7.0
M24 x 1.5 12 1/2 08 U24MSOF1608 30 32.5 3.3 9.3
M30 x 2.0 16 5/8 10 U30MSOF2010 36 38.6 2.0 12.0
M30 x 2.0 19 3/4 12 U30MSOF2012 36 39.5 2.0 13.0
M36 x 2.0 19 3/4 12 U36MSOF2512 46 41.9 3.9 15.0
M42 x 2.0 25 1 16 U42MSOF3016 50 44.9 5.5 19.5
M52 x 2.0 31 1-1/4 20 U52MSOF3820 60 48.8 7.9 26.0
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
MET
RIC
*Only available in ‘B’ & ‘C’ one piece range
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
82
See page 16 for how to order hose assemblies
METRIC CRIMPED NUT FEMALE - DKO 'L'
METRIC LOOSE NUT FEMALE - DKO 'L' Assembly Component E9
Assembly Component F1
*Only available in ‘B’ & ‘C’ one piece range
LIGHT DUTY
LIGHT DUTY
See page 58 for how to order one-piece hose ends
M2 x 1.5 5 3/16 03 U12MSOF0603* 17 17.9 2.0 2.8
M16 x 1.5 10 3/8 06 U16MSOF1006 19 22.2 2.8 5.6
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
M14 x 1.5 6 1/4 04 U14MSOF0804 17 24.2 1.8 4.0
M16 x 1.5 6 1/4 04 U16MSOF1004 19 25.2 2.6 4.0
M16 x 1.5 8 5/16 05 U16MSOF1005* 19 25.2 2.6 5.5
M18 x 1.5 10 3/8 06 U18MSOF1206 22 25.9 2.6 7.0
M22 x 1.5 12 1/2 08 U22MSOF1508 27 27.2 3.4 9.3
M26 x 1.5 12 1/2 08 U26MSOF1808 32 29.3 3.6 9.3
M26 x 1.5 16 5/8 10 U26MSOF1810 32 29.4 3.6 12.0
M30 x 2.0 19 3/4 12 U30MSOF2212 36 32.2 4.5 15.0
M36 x 2.0 25 1 16 U36MSOF2816 41 34.1 4.5 19.5
M45 x 2.0 31 1-1/4 20 U45MSOF3520 50 38.1 4.9 26.0
M52 x 2.0 38 1-1/2 24 U52MSOF4224 60 38.3 4.6 32.0
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
METRIC
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
83
See page 16 for how to order hose assemblies
MET
RIC
METRIC LOOSE NUT FEMALE DKO 'S' 90º SWEPT ELBOW Assembly Component F2HEAVY DUTY
M16 x 1.5 6 1/4 04 U16MSOF0890S04 19 27.2 – 2.8 4.0
M18 x 1.5 6 1/4 04 U18MSOF1090S04 22 27.2 – 3.6 4.0
M20 x 1.5 8 5/16 05 U20MSOF1290S05* 24 28.7 – 3.6 5.5
M20 x 1.5 10 3/8 06 U20MSOF1290S06 24 31.5 36.5 3.6 7.0
M22 x 1.5 10 3/8 06 U22MSOF1490S06 27 31.5 – 3.6 7.0
M24 x 1.5 12 1/2 08 U24MSOF1690S08 30 42.3 46.5 3.3 9.3
M30 x 2.0 16 5/8 10 U30MSOF2090S10 36 47.6 58.5 2.0 12.0
M36 x 2.0 19 3/4 12 U36MSOF2590S12 46 53.8 – 3.9 15.0
M42 x 2.0 25 1 16 U42MSOF3090S16 50 63.8 – 5.5 19.5
M52 x 2.0 31 1-1/4 20 U52MSOF3890S20 60 81.0 – 7.9 26.0
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
*Only available in ‘B’ & ‘C’ one piece rangeSee page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
84
See page 16 for how to order hose assemblies
METRIC CRIMPED NUT FEMALE DKO 'L' 90º SWEPT ELBOW Assembly Component L4LIGHT DUTY
*Only available in ‘B’ & ‘C’ one piece rangeSee page 58 for how to order one-piece hose ends
METRIC LOOSE NUT FEMALE DKO 'L' 90º SWEPT ELBOW
METRIC
Assembly Component F4LIGHT DUTY
M14 x 1.5 6 1/4 04 U14MSOF0890S04 17 27.2 32.9 1.8 4.0
M16 x 1.5 6 1/4 04 U16MSOF1090S04 19 27.2 34.0 2.6 4.0
M16 x 1.5 8 5/16 05 U16MSOF1090S05* 19 28.7 35.3 2.6 5.5
M18 x 1.5 10 3/8 06 U18MSOF1290S06 22 31.5 37.2 2.6 7.0
M22 x 1.5 12 1/2 08 U22MSOF1590S08 27 42.3 42.6 3.4 9.3
M26 x 1.5 12 1/2 08 U26MSOF1890S08 32 42.3 45.2 3.6 9.3
M26 x 1.5 16 5/8 10 U26MSOF1890S10 32 47.6 51.5 3.6 12.0
M30 x 2.0 19 3/4 12 U30MSOF2290S12 36 53.8 59.5 4.5 15.0
M36 x 2.0 25 1 16 U36MSOF2890S16 41 63.8 72.1 4.5 19.5
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
M12 x 1.5 6 1/4 04 U12MSOF0690S04 17 27.2 34.0 2.0 2.8
M16 x 1.5 10 3/8 06 U16MSOF1090S06 19 31.5 39.4 2.8 5.6
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
85
See page 16 for how to order hose assemblies
METRIC LOOSE NUT FEMALE DKO 'S' 45º SWEPT ELBOW Assembly Component F6HEAVY DUTY
MET
RIC
M20 x 1.5 10 3/8 06 U20MSOF1245S06 24 40.8 19.0 3.6 7.0
M22 x 1.5 10 3/8 06 U22MSOF1445S06 27 – – 3.6 7.0
M24 x 1.5 12 1/2 08 U24MSOF1645S08 30 – – 3.3 9.3
M30 x 2.0 16 5/8 10 U30MSOF2045S10 36 – – 2.0 12.0
M36 x 2.0 19 3/4 12 U36MSOF2545S12 46 – – 3.9 15.0
M42 x 2.0 25 1 16 U42MSOF3045S16 50 – – 5.5 19.5
M52 x 2.0 31 1-1/4 20 U52MSOF3845S20 60 – – 7.9 26.0
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
86
See page 16 for how to order hose assemblies
METRIC LOOSE NUT FEMALE DKO 'L' 45º SWEPT ELBOW Assembly Component F7LIGHT DUTY
METRIC
M14 x 1.5 6 1/4 04 U14MSOF0845S04 17 36.4 17.4 1.8 4.0
M16 x 1.5 6 1/4 04 U16MSOF1045S04 19 37.3 18.3 2.6 4.0
M16 x 1.5 8 5/16 05 U16MSOF1045S05* 19 – – 2.6 5.5
M18 x 1.5 10 3/8 06 U18MSOF1245S06 22 41.3 19.5 2.6 7.0
M22 x 1.5 12 1/2 08 U22MSOF1545S08 27 51.4 21.4 3.4 9.3
M26 x 1.5 16 5/8 10 U26MSOF1845S10 32 57.0 25.2 3.6 12.0
M30 x 2.0 19 3/4 12 U30MSOF2245S12 36 – – 4.5 15.0
M36 x 2.0 25 1 16 U36MSOF2845S16 41 – – 4.5 19.5
M45 x 2.0 31 1-1/4 20 U45MSOF3545S20 50 – – 4.9 26.0
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
METRIC CRIMPED NUT FEMALE DKO 'L' 45º SWEPT ELBOW Assembly Component L5LIGHT DUTY
M16 x 1.5 10 3/8 06 U16MSOF1045S06 19 42.8 21.0 2.8 5.6
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
*Only available in ‘B’ & ‘C’ one piece rangeSee page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
87
See page 16 for how to order hose assemblies
METRIC STANDPIPE Assembly Component G4
*Only available in ‘B’ & ‘C’ one piece rangeSee page 58 for how to order one-piece hose ends
MET
RIC
M6 5 3/16 03 U06MS03* 27.8 22.0 2.8
M6 6 1/4 04 U06MS04 28.3 22.0 3.0
M8 5 3/16 03 U08MS03* 29.8 24.0 2.8
M8 6 1/4 04 U08MS04 30.3 24.0 4.0
M10 6 1/4 04 U10MS04 32.3 26.0 4.0
M12 6 1/4 04 U12MS04 32.3 26.0 4.0
M10 8 5/16 05 U10MS05* 32.3 26.0 5.5
M12 8 5/16 05 U12MS05* 32.3 26.0 5.5
M10 10 3/8 06 U10MS06 32.8 26.0 6.0
M12 10 3/8 06 U12MS06 32.8 26.0 7.0
M15 10 3/8 06 U15MS06 31.8 25.0 7.0
M16 10 3/8 06 U16MS06 36.8 30.0 7.0
M12 12 1/2 08 U12MS08 33.1 26.0 7.5
M14 12 1/2 08 U14MS08 36.1 29.0 9.0
M15 12 1/2 08 U15MS08 32.1 25.0 9.3
M16 12 1/2 08 U16MS08 37.1 30.0 9.3
M18 12 1/2 08 U18MS08 33.1 26.0 9.3
M18 16 5/8 10 U18MS10 33.7 26.0 12.0
M20 16 5/8 10 U20MS10 43.7 36.0 12.0
M18 19 3/4 12 U18MS12 34.6 26.0 13.5
M20 19 3/4 12 U20MS12 44.6 36.0 13.1
M22 19 3/4 12 U22MS12 36.6 28.0 15.0
M25 19 3/4 12 U25MS12 48.6 40.0 15.0
M25 25 1 16 U25MS16 50.6 40.0 19.0
M28 25 1 16 U28MS16 40.6 30.0 19.5
NOMINAL HOSE BOREO/D mm mm in dash PART NUMBER Dim A Dim B Dim C
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
88
See page 16 for how to order hose assemblies
METRIC
METRIC STANDPIPE 90° SWEPT ELBOW
Assembly Component G6
M6 6 1/4 04 U06MS90S04 – – 3.0
M8 6 1/4 04 U08MS90S04 – – 4.0
M10 6 1/4 04 U10MS90S04 27.2 49.2 4.0
M10 8 5/16 05 U10MS90S05* – – 5.5
M12 8 5/16 05 U12MS90S05* – – 5.5
M10 10 3/8 06 U10MS90S06 – – 6.0
M12 10 3/8 06 U12MS90S06 – – 7.0
M12 12 1/2 08 U12MS90S08 – – 7.5
M15 12 1/2 08 U15MS90S08 – – 9.3
M16 12 1/2 08 U16MS90S08 – – 9.3
M18 16 5/8 10 U18MS90S10 – – 12.0
M20 19 3/4 12 U20MS90S12 – – 13.1
M22 19 3/4 12 U22MS90S12 – – 15.0
M25 25 1 16 U25MS90S16 – – 19.0
M28 25 1 16 U28MS90S16 – – 19.5
NOMINAL HOSE BOREO/D mm mm in dash PART NUMBER Dim A Dim B Dim C
*Only available in ‘B’ & ‘C’ one piece rangeSee page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
89
See page 16 for how to order hose assemblies
MET
RIC
METRIC STANDPIPE
45° SWEPT ELBOW
Assembly Component G7
M6 6 1/4 04 U06MS45S04 – – 3.0
M8 6 1/4 04 U08MS45S04 – – 4.0
M10 6 1/4 04 U10MS45S04 – – 4.0
M12 10 3/8 06 U12MS45S06 – – 7.0
M12 12 1/2 08 U12MS45S08 – – 7.5
M15 12 1/2 08 U15MS45S08 – – 9.3
M16 12 1/2 08 U16MS45S08 – – 9.3
NOMINAL HOSE BOREO/D mm mm in dash PART NUMBER Dim A Dim B Dim C
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
90
B.S.P. MALE
BSP
Assembly Component A1
NOTE:Dim A represents Hose Cut Off Length
1/8" 02 5 3/16 03 U02BM03* 14 20.7 8.0 2.8
1/8" 02 6 1/4 04 U02BM04 14 21.2 8.0 4.0
1/4" 04 6 1/4 04 U04BM04 19 26.7 11.0 4.0
3/8" 06 6 1/4 04 U06BM04 22 29.2 12.0 4.0
3/8" 06 8 5/16 05 U06BM05* 22 29.7 12.0 5.5
1/4" 04 10 3/8 06 U04BM06 19 27.7 11.0 4.7
3/8" 06 10 3/8 06 U06BM06 22 30.2 12.0 7.0
1/2" 08 10 3/8 06 U08BM06 27 34.7 14.0 7.0
3/8" 06 12 1/2 08 U06BM08 22 30.5 12.0 7.9
1/2" 08 12 1/2 08 U08BM08 27 35.0 14.0 9.3
3/4" 12 12 1/2 08 U12BM08 32 39.0 16.0 9.3
1/2" 08 16 5/8 10 U08BM10 27 35.1 14.0 11.1
5/8" 10 16 5/8 10 U10BM10 30 39.1 16.0 12.0
3/4" 12 19 3/4 12 U12BM12 32 40.0 16.0 15.0
1" 16 25 1 16 U16BM16 41 47.0 19.0 19.5
1-1/4" 20 31 1-1/4 20 U20BM20 50 52.4 20.0 26.0
1-1/2" 24 38 1-1/2 24 U24BM24 55 59.0 22.0 32.0
2" 32 51 2 32 U32BM32 70 71.7 25.0 -
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
See page 16 for how to order hose assemblies*Only available in ‘B’ & ‘C’ one piece range
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
91
See page 16 for how to order hose assemblies*Only available in ‘B’ & ‘C’ one piece range
B.S.P. MALE TAPERED
B.S.P. FEMALE
LOOSE NUT
Assembly Component A2
Assembly Component A3
NOTE:Dim A represents Hose Cut Off Length
NOTE:Dim A represents Hose Cut Off Length
BSP
1/8" 02 5 3/16 03 U02BMT03* 12 20.1 10.0 2.8
1/8" 02 6 1/4 04 U02BMT04 13 20.1 10.0 4.0
1/4" 04 6 1/4 04 U04BMT04 14 24.1 13.0 4.0
3/8" 06 6 1/4 04 U06BMT04 19 27.7 15.0 4.0
1/4" 04 8 5/16 05 U04BMT05* 17 25.9 13.0 5.5
3/8" 06 8 5/16 05 U06BMT05* 19 28.2 15.0 5.5
1/4" 04 10 3/8 06 U04BMT06 17 26.4 13.0 7.0
3/8" 06 10 3/8 06 U06BMT06 19 28.7 15.0 7.0
1/2" 08 10 3/8 06 U08BMT06 22 32.2 18.0 7.0
1/2" 08 12 1/2 08 U08BMT08 22 32.5 18.0 9.3
3/4" 12 19 3/4 12 U12BMT12 30 38.3 20.0 15.0
1" 16 25 1 16 U16BMT16 36 43.0 22.0 19.5
1-1/4" 20 31 1-1/4 20 U20BMT20 46 52.3 25.0 26.0
1-1/2" 24 38 1-1/2 24 U24BMT24 50 53.4 25.0 32.0
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
1/4" 04 5 3/16 03 U04BF03* 19 16.0 5.2 2.8
1/4" 04 6 1/4 04 U04BF04 19 16.5 5.2 4.0
3/8" 06 6 1/4 04 U06BF04 22 19.1 6.0 4.0
3/8" 06 8 5/16 05 U06BF05* 22 19.1 6.0 5.5
3/8" 06 10 3/8 06 U06BF06 22 19.6 6.0 7.0
3/8" 06 10 3/8 06 U08BF06 27 20.5 6.5 7.0
1/2" 08 12 1/2 08 U08BF08 27 20.8 6.5 9.3
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
92
See page 16 for how to order hose assemblies
B.S.P. FEMALE Assembly Component A3
*Only available in ‘B’ & ‘C’ one piece rangeSee page 58 for how to order one-piece hose ends
1/8" 02 5 3/16 03 U02BF03* 14 15.0 4.3 2.8
1/8" 02 6 1/4 04 U02BF04 14 15.5 4.3 2.8
1/4" 04 8 5/16 05 U04BF05* 19 18.0 5.2 4.5
1/4" 04 10 3/8 06 U04BF06 19 18.7 5.2 4.0
3/8" 06 12 1/2 08 U06BF08 22 20.2 6.0 7.0
5/8" 10 12 1/2 08 U10BF08 30 20.0 9.7 9.3
3/4" 12 12 1/2 08 U12BF08 32 23.2 9.0 9.3
1/2" 08 16 5/8 10 U08BF10 27 22.8 6.5 9.3
5/8" 10 16 5/8 10 U10BF10 30 20.1 9.7 12.0
3/4" 12 16 5/8 10 U12BF10 32 23.3 9.0 12.0
1/2" 08 19 3/4 12 U08BF12 27 23.7 6.5 9.3
3/4" 12 19 3/4 12 U12BF12 32 24.2 9.0 15.0
1" 16 19 3/4 12 U16BF12 41 29.2 10.5 15.0
1" 16 25 1 16 U16BF16 41 27.7 10.5 19.5
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
WIRED ON NUT
BSP
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
93
See page 16 for how to order hose assemblies
B.S.P. FEMALE 90° SWEPT ELBOW
B.S.P. FEMALE 90° SWEPT ELBOW
Assembly Component A5
Assembly Component A5
LOOSE NUT
WIRED ON NUT
*Only available in ‘B’ & ‘C’ one piece range
1/4" 04 5 3/16 03 U04BF90S03* 19 24.3 27.1 5.2 2.8
1/4" 04 6 1/4 04 U04BF90S04 19 27.2 28.8 5.2 4.0
3/8" 06 6 1/4 04 U06BF90S04 22 27.2 32.0 6.0 4.0
3/8" 06 8 5/16 05 U06BF90S05* 22 28.7 34.1 6.0 5.5
3/8" 06 10 3/8 06 U06BF90S06 22 31.5 34.1 6.0 7.0
1/2" 08 10 3/8 06 U08BF90S06 27 31.5 36.5 6.5 7.0
1/2" 08 12 1/2 08 U08BF90S08 27 42.3 40.4 6.5 9.3
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
1/8" 02 5 3/16 03 U02BF90S03 14 24.3 29.4 4.3 2.8
1/8" 02 6 1/4 04 U02BF90S04 14 27.2 31.1 4.3 2.8
1/4" 04 10 3/8 06 U04BF90S06 19 31.5 37.3 5.2 4.5
3/8" 06 12 1/2 08 U06BF90S08 22 42.3 43.6 6.0 7.0
5/8" 10 16 5/8 10 U10BF90S10 30 47.6 52.2 9.7 12.0
3/4" 12 16 5/8 10 U12BF90S10 32 47.6 56.9 9.0 12.0
3/4" 12 19 3/4 12 U12BF90S12 32 53.8 63.4 9.0 15.0
1" 16 19 3/4 12 U16BF90S12 41 53.8 69.0 10.5 15.0
1" 16 25 1 16 U16BF90S16 41 63.8 78.7 10.5 19.5
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZEBS
P
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
94
See page 16 for how to order hose assemblies
BSP
B.S.P. FEMALE 45º SWEPT ELBOW
B.S.P. FEMALE 45º SWEPT ELBOW
LOOSE NUT
WIRED ON NUT
Assembly Component A7
Assembly Component A7
*Only available in ‘B’ & ‘C’ one piece rangeSee page 58 for how to order one-piece hose ends
1/4" 04 6 1/4 04 U04BF45S04 19 36.3 14.6 5.2 4.0
3/8" 06 8 5/16 05 U06BF45S05* 22 37.8 17.9 6.0 5.5
3/8" 06 10 3/8 06 U06BF45S06 22 39.1 17.3 6.0 7.0
1/2" 08 12 1/2 08 U08BF45S08 27 49.9 19.9 6.5 9.3
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
1/8" 02 5 3/16 03 U02BF45S03* 14 36.4 16.5 4.3 2.8
5/8" 10 12 1/2 08 U10BF45S08 30 52.8 22.8 9.7 9.3
5/8" 10 16 5/8 10 U10BF45S10 30 57.5 25.7 9.7 12.0
3/4" 12 19 3/4 12 U12BF45S12 32 66.8 31.6 9.0 15.0
1" 16 25 1 16 U16BF45S16 41 80.4 39.4 19.5 19.5
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
95
See page 16 for How to order hose assemblies
BSP
B.S.P. 90° COMPACT FEMALE Assembly Component A8WIRED ON NUT
See page 58 for how to order one-piece hose ends
1/4" 04 6 1/4 04 U04BOF04 19 16.5 5.2 4.0
3/8" 06 6 1/4 04 U06BOF04 22 19.1 6.0 4.0
3/8" 06 10 3/8 06 U06BOF06 22 19.6 6.0 7.0
1/2" 08 12 1/2 08 U08BOF08 27 20.8 6.5 9.3
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
1/8" 02 5 3/16 03 U02BF90K03* 14 16.8 18.4 4.3 2.8
1/4" 04 6 1/4 04 U04BF90K04 19 17.3 21.3 5.2 4.0
3/8" 06 6 1/4 04 U06BF90K04 22 18.5 23.5 6.0 4.0
3/8" 06 8 5/16 05 U06BF90K05* 22 18.5 23.5 6.0 5.5
3/8" 06 10 3/8 06 U06BF90K06 22 18.9 23.5 6.0 7.0
1/2" 08 10 3/8 06 U08BF90K06 27 21.1 29.0 6.5 7.0
1/2" 08 12 1/2 08 U08BF90K08 27 21.4 29.0 6.5 9.3
5/8" 10 16 5/8 10 U10BF90K10 30 27.0 29.2 9.7 12.0
3/4" 12 19 3/4 12 U12BF90K12 32 27.4 31.7 9.0 15.0
1" 16 25 1 16 U16BF90K16 41 33.6 38.1 10.5 19.5
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
B.S.P. 'O' RING SEALING FEMALE Assembly Component B1LOOSE NUT
*Only available in ‘B’ & ‘C’ one piece range
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
96
See page 16 for how to order hose assemblies
B.S.P. 'O' RING SEALING FEMALE
B.S.P. 'O' RING SEALING FEMALE 90° SWEPT ELBOW
Assembly Component B1
Assembly Component B3
WIRED ON NUT
LOOSE NUT
See page 58 for how to order one-piece hose ends
BSP
3/8" 06 12 1/2 08 U06BOF08 22 20.2 6.0 7.0
5/8" 10 16 5/8 10 U10BOF10 30 20.1 9.7 12.0
3/4" 12 19 3/4 12 U12BOF12 32 24.2 9.0 15.0
1" 16 25 1 16 U16BOF16 41 27.7 10.5 19.5
1-1/4" 20 31 1-1/4 20 U20BOF20 50 30.9 10.1 26.0
1-1/2" 24 38 1-1/2 24 U24BOF24 55 29.7 12.5 32.0
2" 32 51 2 32 U32BOF32 70 31.4 16.1 –
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
1/4" 04 6 1/4 04 U04BOF90S04 19 27.2 28.8 5.2 4.0
3/8" 06 10 3/8 06 U06BOF90S06 22 31.5 34.1 6.0 7.0
1/2" 08 12 1/2 08 U08BOF90S08 27 42.3 40.4 6.5 9.3
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
97
WIRED ON NUTWIRED ON NUTWIRED ON NUTWIRED ON NUTB.S.P. 'O' RING SEALING FEMALE 90° SWEPT ELBOW WIRED ON NUT
Assembly Component B3
See page 16 for how to order hose assemblies See page 58 for how to order one-piece hose ends
BSP
1/4" 04 6 1/4 04 U04BOF45S04 19 36.3 14.6 5.2 4.0
3/8" 06 10 3/8 06 U06BOF45S06 22 39.1 17.3 6.0 7.0
1/2" 08 12 1/2 08 U08BOF45S08 27 49.9 19.9 6.5 9.3
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
5/8" 10 16 5/8 10 U10BOF90S10 30 47.6 52.2 9.7 12.0
3/4" 12 19 3/4 12 U12BOF90S12 32 53.8 63.4 9.0 15.0
1" 16 25 1 16 U16BOF90S16 41 63.8 78.7 10.5 19.5
1-1/4" 20 31 1-1/4 20 U20BOF90S20 50 81.0 93.5 10.1 26.0
1-1/2" 24 38 1-1/2 24 U24BOF90S24 55 106.4 100.7 12.5 32.0
2" 32 51 2 32 U32BOF90S32 70 136.1 145.2 16.1 –
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
B.S.P. 'O' RING SEALING FEMALE 45° SWEPT ELBOW Assembly Component B5LOOSE NUT
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
98
See page 16 for how to order hose assemblies
BSP
B.S.P. 'O' RING SEALING FEMALE 45° SWEPT ELBOW
B.S.P. 'O' RING SEALING 90° COMPACT FEMALE WIRED ON NUT
Assembly Component B5
Assembly Component K7
WIRED ON NUT
See page 58 for how to order one-piece hose ends
5/8" 10 16 5/8 10 U10BOF45S10 30 57.5 25.7 9.7 12.0
3/4" 12 19 3/4 12 U12BOF45S12 32 66.8 31.6 9.0 15.0
1" 16 25 1 16 U16BOF45S16 41 80.4 39.4 10.5 19.5
1-1/4" 20 31 1-1/4 20 U20BOF45S20 50 99.1 46.2 10.1 26.0
1-1/2" 24 38 1-1/2 24 U24BOF45S24 55 117.5 46.3 12.5 32.0
2" 32 51 2 32 U32BOF45S32 70 162.2 71.0 16.1 –
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
1/4" 04 6 1/4 04 U04BOF90K04 19 17.3 21.3 5.2 4.0
3/8" 06 10 3/8 06 U06BOF90K06 22 18.9 23.5 6.0 7.0
1/2" 08 12 1/2 08 U08BOF90K08 27 21.4 29.0 6.5 9.3
3/4" 12 19 3/4 12 U12BOF90K12 32 27.4 31.7 9.0 15.0
1" 16 25 1 16 U16BOF90K16 41 33.6 38.1 10.5 19.5
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
99
See page 16 for how to order hose assemblies
BSP
See page 58 for how to order one-piece hose ends
1/4" 04 6 1/4 04 U04BFF04 19 12.8 8.9 4.0
3/8" 06 6 1/4 04 U06BFF04 22 14.4 10.7 4.0
3/8" 06 10 3/8 06 U06BFF06 22 14.9 10.7 7.0
1/2" 08 10 3/8 06 U08BFF06 27 15.2 11.8 7.0
1/2" 08 12 1/2 08 U08BFF08 27 15.5 11.8 9.3
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
3/4" 12 12 1/2 08 U12BFF08 32 20.7 11.5 9.3
3/4" 12 19 3/4 12 U12BFF12 32 21.7 11.5 15.0
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
B.S.P. FLAT FACE FEMALE Assembly Component B6LOOSE NUT
B.S.P. FLAT FACE FEMALE Assembly Component B6WIRED ON NUT
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
100
See page 16 for how to order hose assemblies
B.S.P. BANJO
B.S.P. BANJO BOLT
Assembly Component B8
See page 58 for how to order one-piece hose ends
BSP
1/4" 04 6 1/4 04 U04BG04 22.6 15.2 4.0
3/8" 06 6 1/4 04 U06BG04 23.4 20.3 4.0
3/8" 06 10 3/8 06 U06BG06 23.9 20.3 7.0
1/2" 08 10 3/8 06 U08BG06 29.5 25.4 7.0
1/2" 08 12 1/2 08 U08BG08 29.7 25.4 9.3
3/4" 12 19 3/4 12 U12BG12 36.3 30.0 15.0
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER Dim A Dim B Dim C
SIZE
1/4" 04 RX04BMG 19 35.1 6.1
3/8" 06 RX06BMG 22 42.9 6.9
1/2" 08 RX08BMG 27 53.1 8.6
3/4" 12 RX12BMG 32 62.0 10.2
B.S.P.THREAD DASH No. PART NUMBER A/F Dim A Dim B
SIZE
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
101
See page 16 for how to order hose assemblies*Only available in ‘B’ & ‘C’ one piece range
See page 58 for how to order one-piece hose ends
N.P.T.F. FIXED FEMALE Assembly Component H2
1/4" x 18 04 5 3/16 03 U04FNF03 19.0 24.8 2.8
1/4" x 18 04 6 1/4 04 U04FNF04 19.0 25.3 4.0
3/8" x 18 06 6 1/4 04 U06FNF04 22.2 25.7 4.0
1/4" x 18 04 10 3/8 06 U04FNF06 19.0 26.3 7.0
1/2" x 14 08 10 3/8 06 U08FNF06 27.0 31.1 7.0
3/8" x 18 06 12 1/2 08 U06FNF08 22.2 26.9 9.3
1/2" x 14 08 12 1/2 08 U08FNF08 27.0 31.4 9.3
3/4" x 14 12 19 3/4 12 U12FNF12 41.3 34.5 15.0
N/P.T.F.NOMINAL HOSE BORE
THREADDASH No. mm in dash PART NUMBER A/F Dim A Dim B
1/4" 04 6 1/4 04 U04BJF04 19 13.6 8.1 4.0
3/8" 06 10 3/8 06 U06BJF06 22 15.8 9.8 7.0
1/2" 08 12 1/2 08 U08BJF08 27 16.2 11.2 9.3
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
B.S.P. 60° JIS FEMALE Assembly Component B7LOOSE NUT
MIS
CELL
ANOU
S
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
102
See page 16 for how to order hose assemblies
MISCELLANOUS
WATERWASH INSERTS Assembly Component L8RUBBER COVERED NUT
M22 x 1.5 6 1/4 04 U22RKF04 27.3 35.0 4.0
M22 x 1.5 8 5/16 05 U22RKF05* 27.9 35.0 5.5
M22 x 1.5 10 3/8 06 U22RKF06 28.3 35.0 7.0
NOMINAL HOSE BORETHREAD mm in dash PART NUMBER Dim A Dim B Dim C
SIZE
HOSE JOINERS Assembly Component L9
NOMINAL HOSE BORE
mm in dash PART NUMBER Dim A Dim B Dim C
6 1/4 04 U04SV04 13.6 68.6 4.0
8 5/16 05 U05SV05 13.6 69.6 5.5
10 3/8 06 U06SV06 14.6 73.4 7.0
12 1/2 08 U08SV08 15.2 77.6 9.3
*Only available in ‘B’ & ‘C’ one piece rangeSee page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
103
See page 16 for how to order hose assemblies
MIS
CELL
ANOU
S
METRIC 60° CONE FEMALE Assembly Component F9
See page 58 for how to order one-piece hose ends
M14 x 1.5 6 1/4 04 U14MJF04 19 15.8 9.7 4.0
M18 x 1.5 10 3/8 06 U18MJF06 22 17.3 10.0 7.0
M22 x 1.5 12 1/2 08 U22MJF08 27 17.3 11.2 9.3
M24 x 1.5 16 5/8 10 U24MJF10 30 20.9 13.0 12.0
M30 x 1.5 19 3/4 12 U30MJF12 36 22.3 18.5 15.0
N/P.T.F. NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
3/4" 12 19 3/4 12 U12BJF12 32 21.3 11.9 15.0
1" 16 25 1 16 U16BJF16 41 24.8 13.5 19.5
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
B.S.P. 60° JIS FEMALE Assembly Component B7WIRED ON NUT
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
104
INTERLOCK FERRULES
B.S.P. MALE A1
INTERLOCK BSP
Assembly Component
See page 58 for how to order one-piece hose ends
NOMINAL HOSE BORE
mm in dash PART NUMBER Dim A Dim B
19 3/4 12 HP12FP 38.0 60.0
25 1 16 HP16FP 46.0 74.5
31 1-1/4 20 HP20FP 55.0 88.0
31 1-1/4 20 HP20Z 60.0 88.0
38 1-1/2 24 HP24FP 62.0 94.0
38 1-1/2 24 HP24Z 67.0 94.0
51 2 32 HP32FP 78.1 99.1
51 2 32 HP32Z 84.5 98.9
51 2 32 HP32-920 83.7 98.9
3/4" 12 19 3/4 12 HP12BM12 32 39.4 16.0 14.0
1" 16 25 1 16 HP16BM16 41 46.2 19.0 20.0
1-1/4" 20 31 1-1/4 20 HP20BM20 50 52.4 20.0 26.0
1-1/2" 24 38 1-1/2 24 HP24BM24 55 58.9 22.0 31.8
2" 32 51 2 32 HP32BM32 70 68.1 25.0 42.0
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
105
B.S.P. MALE TAPERED A2
INTE
RLOC
K BS
P
Assembly Component
3/4" 12 19 3/4 12 HP12BMT12 30 37.6 20.0 14.0
1" 16 25 1 16 HP16BMT16 36 42.5 22.0 20.0
1-1/4" 20 31 1-1/4 20 HP20BMT20 46 52.7 25.0 26.0
1-1/2" 24 38 1-1/2 24 HP24BMT24 50 53.4 25.0 31.8
2" 32 51 2 32 HP32BMT32 60 57.0 29.0 42.0
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
3/4" 12 19 3/4 12 HP12BOF12 32 24.0 6.9 14.0
1" 16 25 1 16 HP16BOF16 41 26.2 13.0 20.0
1-1/4" 20 31 1-1/4 20 HP20BOF20 50 30.7 11.6 26.0
1-1/2" 24 38 1-1/2 24 HP24BOF24 55 32.0 13.6 31.8
2" 32 51 2 32 HP32BOF32 70 34.5 13.7 42.0
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
B.S.P. 'O' RING SEALING FEMALE
WIRED ON NUT
Assembly Component B1
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
106
B.S.P. 'O' RING SEALING FEMALE 45°SWEPT ELBOW
B.S.P. 'O' RING SEALING FEMALE 90°SWEPT ELBOW
WIRED ON NUT
WIRED ON NUT
Assembly Component B3
Assembly Component B5
See page 58 for how to order one-piece hose ends
INTERLOCK BSP
3/4" 12 19 3/4 12 HP12BOF90S12 32 51.1 64.0 6.9 14.0
1" 16 25 1 16 HP16BOF90S16 41 75.4 87.4 8.9 20.0
1-1/4" 20 31 1-1/4 20 HP20BOF90S20 50 84.8 98.3 10.2 26.0
1-1/2" 24 38 1-1/2 24 HP24BOF90S24 55 97.4 118.1 11.9 32.0
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
1" 16 25 1 16 HP16BOF45S16 41 95.3 43.7 8.9 20.0
1-1/4" 20 31 1-1/4 20 HP20BOF45S20 50 100.3 46.7 10.2 26.0
1-1/2" 24 38 1-1/2 24 HP24BOF45S24 55 117.3 57.4 11.9 32.0
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
107
1-1/16" x 12 12 19 3/4 12 HP12JM12 28 34.0 22.0 14.0
1-5/16" x 12 16 19 3/4 12 HP16JM12 36 37.0 23.0 14.0
1-5/16" x 12 16 25 1 16 HP16JM16 36 38.0 23.0 20.0
1-5/8" x 12 20 31 1-1/4 20 HP20JM20 46 42.7 24.3 26.0
1-7/8" x 12 24 38 1-1/2 24 HP24JM24 50 46.1 27.5 31.8
2-1/2" x 12 32 51 2 32 HP32JM32 65 55.5 34.0 42.0
NOMINAL HOSE BOREJIC THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
1-1/16" x 12 12 19 3/4 12 HP12JF12 32 19.0 14.2 14.0
1-3/16" x 12 16 19 3/4 12 HP16JF12 38 20.0 15.0 14.0
1-5/16" x 12 16 25 1 16 HP21JF16 38 21.0 15.0 20.0
1-5/8" x 12 20 31 1-1/4 20 HP20JF20 50 24.0 15.8 26.0
1-7/8" x 12 24 38 1-1/2 24 HP24JF24 55 26.5 18.5 31.8
2-1/2" x 12 32 51 2 32 HP32JF32 70 29.5 23.9 42.0
NOMINAL HOSE BOREJIC THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
J.I.C. FEMALE
WIRED ON NUT
J.I.C. MALE Assembly Component B9
Assembly Component C1
INTE
RLOC
K JI
C
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
108
J.I.C. FEMALE 90° SWEPT ELBOW
J.I.C. FEMALE 45° SWEPT ELBOW
WIRED ON NUT
WIRED ON NUT
Assembly Component C3
Assembly Component C5
See page 58 for how to order one-piece hose ends
INTERLOCK JIC
1-1/16" x 12 12 19 3/4 12 HP12JF90S12 32 51.1 65.0 14.2 14.0
1-5/16" x 12 16 25 1 16 HP16JF90S16 41 75.4 87.1 15.0 20.0
1-5/8" x 12 20 31 1-1/4 20 HP20JF90S20 50 84.8 97.3 15.8 26.0
1-7/8" x 12 24 38 1-1/2 24 HP24JF90S24 60 97.0 115.8 18.5 31.8
NOMINAL HOSE BOREJIC THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
1-1/16" x 12 12 19 3/4 12 HP12JF45S12 32 66.5 34.3 14.2 14.0
1-5/16" x 12 16 19 3/4 12 HP16JF45S16 41 94.2 43.4 15.0 20.0
1-5/8" x 12 20 31 1-1/4 20 HP20JF45S20 50 99.8 46.2 15.8 26.0
NOMINAL HOSE BOREJIC THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
109
S.A.E. / I.S.O. FLANGE 90° SWEPT ELBOW
S.A.E. / I.S.O. FLANGE STRAIGHT INSERT
CODE 62
CODE 62
Assembly Component L1
Assembly Component L2
INTE
RLOC
KSA
E FL
ANGE
19 3/4 12 19 3/4 12 HP12SFH612 50.0 41.3 14.0
25 1 16 19 3/4 12 HP16SFH612 69.2 47.6 14.0
25 1 16 25 1 16 HP16SFH616 57.5 47.6 20.0
32 1-1/4 20 25 1 16 HP20SFH616 65.8 54.0 20.0
32 1-1/4 20 31 1-1/4 20 HP20SFH620 67.0 54.0 26.0
38 1-1/2 24 38 1-1/2 24 HP24SFH624 73.3 63.5 31.8
51 2 32 38 1-1/2 24 HP32SFH624 93.2 79.4 31.8
51 2 32 51 2 32 HP32SFH632 84.8 79.4 42.0
NOMINAL FLANGE SIZE NOMINAL HOSE BORE
mm in dash mm in dash PART NUMBER Dim A Dim B Dim C
19 3/4 12 19 3/4 12 HP12SFH90S612 55.1 55.6 41.3 14.0
25 1 16 19 3/4 12 HP16SFH90S612 51.1 69.6 47.6 14.0
25 1 16 25 1 16 HP16SFH90S616 75.4 70.1 47.6 20.0
32 1-1/4 20 25 1 16 HP20SFH90S616 75.4 79.2 54.0 20.0
32 1-1/4 20 31 1-1/4 20 HP20SFH90S620 84.8 89.9 54.0 26.0
32 1-1/4 20 31 1-1/4 20 HP24SFH90S620 84.8 97.3 63.5 26.0
38 1-1/2 24 38 1-1/2 24 HP24SFH90S624 97.0 123.2 63.5 31.8
51 2 32 51 2 32 HP32SFH90S632 142.0 154.9 79.4 42.0
NOMINAL FLANGE SIZE NOMINAL HOSE BORE
mm in dash mm in dash PART NUMBER Dim A Dim B Dim C Dim D
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
110
S.A.E. / I.S.O. FLANGE 45° SWEPT ELBOW
CODE 62
S.A.E. / I.S.O. SPLIT FLANGE CLAMPS CODE 62
Assembly Component L3
See page 58 for how to order one-piece hose ends
INTERLOCKSAE FLANGE
19 3/4 12 19 3/4 12 HP12SFH45S612 63.0 26.2 41.3 14.0
25 1 16 25 1 16 HP16SFH45S616 87.1 34.5 47.6 20.0
32 1-1/4 20 25 1 16 HP20SFH45S616 90.9 39.9 54.0 20.0
32 1-1/4 20 31 1-1/4 20 HP20SFH45S620 100.6 47.0 54.0 26.0
38 1-1/2 24 38 1-1/2 24 HP24SFH45S624 121.4 61.0 63.5 31.8
NOMINAL FLANGE SIZE NOMINAL HOSE BORE
mm in dash mm in dash PART NUMBER Dim A Dim B Dim C Dim D
13 1/2 08 RX08SFC6 – – – – – – 9.0 –
19 3/4 12 RX12SFC6 – – – – – – 11.0 –
25 1 16 RX16SFC6 – – – – – – 13.0 –
32 1-1/4 20 RX20SFC6 – – – – – – 15.0 –
38 1-1/2 24 RX24SFC6 – – – – – – 17.0 –
51 2 32 RX32SFC6 – – – – – – 21.0 –
NOMINAL FLANGE SIZE
mm in dash PART NUMBER Dim A Dim B Dim C Dim D Dim E Dim F Dim G Dim H
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
111
METRIC LOOSE NUT FEMALE DKO ‘S’
METRIC LOOSE NUT FEMALE DKO 'S' 90° SWEPT ELBOW
HEAVY-DUTY
HEAVY-DUTY
Assembly Component E8
Assembly Component F2
INTE
RLOC
KM
ETRI
C/NP
TF
36 x 2.0 19 3/4 12 HP36MSOF2512 46 37.1 3.9 14.0
42 x 2.0 25 1 16 HP42MSOF3016 50 40.1 5.5 20.0
52 x 2.0 31 1-1/4 20 HP52MSOF3820 60 44.5 7.7 26.0
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
42 x 2.0 25 1 16 HP42MSOF3090S16 50 75.4 75.9 5.5 20.0
52 x 2.0 31 1-1/4 20 HP52MSOF3890S20 60 84.8 97.3 7.7 26.0
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
112
N.P.T.F. MALE
METRIC LOOSE NUT FEMALE DKO 'S' 45° SWEPT ELBOWHEAVY-DUTY
Assembly Component F6
Assembly Component H3
See page 58 for how to order one-piece hose ends
INTERLOCKM
ETRIC/NPTF
42 x 2.0 25 1 16 HP42MSOF3045S16 50 90.4 39.6 5.5 20.0
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C Dim D
SIZE
3/4 x 14 12 19 3/4 12 HP12NM12 27 40.8 19.3 14.0
1 x 11.5 16 25 1 16 HP16NM16 36 46.3 23.8 20.0
1-1/4 x 11.5 20 31 1-1/4 20 HP20NM20 46 56.7 24.6 26.0
1-1/2 x 11.5 24 38 1-1/2 24 HP24NM24 50 53.8 25.4 31.8
2 x 11.5 32 51 2 32 HP32NM32 65 60.3 26.2 42.0
N.P.T.F. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
113
CRIMPED FERRULE FOR USE ON VERY HIGH PRESSURE THERMOPLASTIC HOSE
CRIMPED FERRULE FOR USE ON VERY HIGH PRESSURE THERMOPLASTIC HOSE
NOMINAL HOSE BORE
mm in dash PART NUMBER Dim A Dim B
6 1/4 04 ET04-352 19.9 38.1
10 3/8 06 ET06-352 25.4 43.5
NOMINAL HOSE BORE
mm in dash PART NUMBER Dim A Dim B
6 1/4 04 ET04-852 20.6 38.1
HIGH
PRE
SSUR
ETH
ERM
O FE
RRUL
ES
See page 58 for how to order one-piece hose ends
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
114
CRIMPED FERRULE FOR USE ON VERY HIGH PRESSURE THERMOPLASTIC HOSE
See page 58 for how to order one-piece hose ends
HIGH PRESSURETHERM
O FERRULES
CRIMPED FERRULE FOR USE ON VERY HIGH PRESSURE THERMOPLASTIC HOSE
NOMINAL HOSE BORE
mm in dash PART NUMBER Dim A Dim B
10 3/8 06 ET06-754 23.8 43.5
12 1/2 08 ET08-754 28.6 50.4
NOMINAL HOSE BORE
mm in dash PART NUMBER Dim A Dim B
12 1/2 08 ET08-755 31.8 45.7
19 3/4 12 ET12-755 39.7 60.0
25 1 16 ET16-755 47.6 61.4
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
115
B.S.P. FEMALE
B.S.P. MALE
WIRED ON NUT
B.S.P. FEMALELOOSE NUT
Assembly Component A1
Assembly Component A3
Assembly Component A3
HIGH
PRE
SSUR
ETH
ERM
O BS
P
See page 58 for how to order one-piece hose ends
3/8" 06 6 1/4 04 ET06BF04 22 20.3 6.0 3.8
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
1/4" 04 6 1/4 04 ET04BM04 19 29.1 11.0 3.8
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
1/4" 04 6 1/4 04 ET04BF04 19 18.9 5.2 3.8
3/8" 06 10 3/8 06 ET06BF06 22 20.6 6.0 7.0
1/2" 08 12 1/2 08 ET08BF08 27 23.7 6.5 9.0
3/4" 12 19 3/4 12 ET12BF12 32 25.0 9.0 14.0
B.S.P. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
116
METRIC MALE
METRIC LOOSE NUT FEMALE - DKO ‘S’
J.I.C. FEMALE
HEAVY-DUTY
WIRED ON NUT
Assembly Component C1
Assembly Component T2
Assembly Component E8
See page 58 for how to order one-piece hose ends
HIGH PRESSURETHERM
O JIC/METRIC
– 04 – – 4 ET04JF04 – – – –
1/2" x 20 08 6 1/4 04 ET05JF04 17 17.2 9.5 3.8
9/16" x 18 06 6 1/4 04 ET06JF04 19 16.7 8.7 3.8
– 06 – – 06 ET06JF06 – – – –
– 08 – – 08 ET08JF08 – – – –
– 12 – – 12 ET12JF12 – – – –
– 16 – – 12 ET16JF12 – – – –
– 16 – – 16 ET16JF16 – – – –
NOMINAL HOSE BOREJIC THREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
12 x 1.5 6 1/4 04 ET12MMW04 17 29.1 12.0 3.8
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
16 x 1.5 6 1/4 04 ET16MSOF0804 19 27.4 2.8 3.8
18 x 1.5 6 1/4 04 ET18MSOF1004 22 28.4 3.7 3.8
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
See page 16 for how to order hose assemblies
117
N.P.T.F. MALE
N.P.S.M. FEMALE
METRIC LOOSE NUT FEMALE - DKO ‘L’LIGHT-DUTY
WIRED ON NUT Airless paint spray
Assembly Component E9
Assembly Component H3
Assembly Component L7
HIGH
PRE
SSUR
E TH
ERM
OM
ETRI
C/NP
TF/N
PSM
See page 58 for how to order one-piece hose ends
1/8 x 27 02 6 1/4 04 ET02NM04 17 28.6 9.5 3.8
1/4 x 18 04 6 1/4 04 ET04NM04 17 29.6 14.5 3.8
3/8 x 18 06 6 1/4 04 ET06NM04 19 29.6 14.5 7.0
3/8 x 18 06 10 3/8 06 ET06NM06 19 33.8 14.5 7.0
1/2 x 14 08 12 1/2 08 ET08NM08 22 41.4 19.3 9.0
3/4 x 14 12 19 3/4 12 ET12NM12 27 43.0 19.3 14.0
1 x 11.5 16 25 1 16 ET16NM16 36 48.9 23.8 20.0
N.P.T.F. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
1/4 04 8 1/4 04 ET04NSF04 19 18.9 4.2 3.8
3/8 06 10 3/8 06 ET06NSF06 22 20.6 5.3 7.0
1/2 08 12 1/2 08 ET08NSF08 27 23.7 6.4 9.0
3/4 12 19 3/4 12 ET12NSF12 32 25.0 9.0 14.0
N.P.T.F. NOMINAL HOSE BORETHREAD DASH No. mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
14 x 1.5 6 1/4 04 ET14MSOF08-04 19 23.1 3.8 3.8
METRIC NOMINAL HOSE BORETHREAD mm in dash PART NUMBER A/F Dim A Dim B Dim C
SIZE
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
118
PRESSURE TEST SYSTEMS
Monitoring couplings allow equipment to bemonitored, tested and bled rapidly, accurately andcleanly.
These tasks can be performed while the systemis operating, because the monitoring coupling canbe connected under pressure to the appropriateinstruments or testing devices.
When the connecting hose is coupled, or pluggedin, a check valve in the monitoring coupling isopened and pressure measurements can be made.A built-in o-ring seal prevents fluid from escaping.When the connecting hose is uncoupled, orremoved, the check valve closes.
Plug-in Type
Pressure to 400 bar(6,000 psi)
Pressure to 600 bar(9,000 psi)
Threaded Type
Pressure Test Systems – Micro Hose Assemblies
Wyco V ClampRear Mount
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
119
MICRO HOSE ASSEMBLIES
Micro HoseSpecifications:
Operating Temperature Range:-40°C to 100°C(-40°F to 212°F)
Standard Color:Black
Materials:Outer Cover – NylonInner Core – NylonReinforcement – Kevlar
PART ORDER DIAMETER MINIMUM BEND WORKING BURST WEIGHTNUMBER NUMBER REINFORCEMENT I.D./O.D RADIUS PRESSURE PRESSURE Kg/100 METERS
K KEVLAR 2.0mm 4.9mm 20mm (3/4") 475 bar (6,900 psi) 1900 bar (27,500 psi) 1.6MH2.2K (.078) (.193) (1.08 lbs/100 ft.)
How to Order Hose Assemblies
ENDFITTING
HOSETYPE
ENDFITTING
OVERALLLENGTHInches
Metric TestPoint
Connector(M16 x 2)
KEVLARReinforced
Hose
37° JICFemaleSwivelSize 4
24InchesLength
A - K - J4 - 24EXAMPLEM
ICRO
HOS
E
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
120
MICRO HOSE COMPONENTS
METRIC TEST-POINT CONNECTOR
MONITORING PLUG
DIN METRIC FEMALE CONNECTOR
STANDPIPE
THREAD ASSEMBLY PARTSIZE COMPONENT NUMBER
M16 x 2 A MH16 x 2MM16 x 1.5 A1 MH16 x 1.5M
PARTASSEMBLY COMMPONENT NUMBER
B MHP
ASSEMBLY PARTSIZE THREAD COMPONENT NUMBER6L M12 x 1.5 C MH6L6S M14 x 1.5 C1 MH6S8L M14 x 1.5 D MH8L8S M16 x 1.5 D1 MH8S
TUBE ASSEMBLY PARTO.D COMPONENT NUMBER
6mm E MH6T
*To order Dust Cap separatelyuse part number MHCP
*
*To order Ferrule separatelyuse part number MHGS-2
*
See page 119 for how to order hose assemblies
MICRO HOSE
COMPONENTS
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
121
MICRO HOSE COMPONENTS
JIC 37° FEMALE SWIVEL
MALE PIPE (NPTF) (BSPT)
RIGID FEMALE PIPE (NPTF)
UNION
ASSEMBLY PARTSIZE THREAD COMPONENT NUMBER
3 3/8 - 24 J3 MH3JIC4 7/16 - 20 J4 MH4JIC4 7/16 - 20 J4H* MH4JICH5 1/2 - 20 J5 MH5JIC
THREAD ASSEMBLY PARTSIZE COMPONENT NUMBER
1/4 x 18 F4 MH4FP
THREAD ASSEMBLY PARTSIZE COMPONENT NUMBER
M16 x 2 MHU MHU
THREAD NPTF ASSEMBLY BSPT ASSEMBLY PARTSIZE COMPONENT COMPONENT NUMBER
1/8 - 27 P2 - MH2P1/8 - 28 - T2 MH2RK1/4 - 18 P4 - MH4P1/4 - 19 - T4 MH4RK3/8 - 18 P5 - MH6P3/8 - 19 - T6 MH6RK
•For Air and Gas Applications
MIC
RO H
OSE
COM
-PO
NENT
S
See page 119 for how to order hose assemblies
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
PRESSURE GAUGEADAPTERS
122
PRESSURE GAUGE ADAPTERS
NPT PRESSURE GAUGE TO THREADED MONITORING COUPLING
BSPP PRESSURE GAUGE TO THREADED MONITORING COUPLING
NPT PRESSURE GAUGE TO MONITORING PLUG
BSPP PRESSURE GAUGE TO MONITORING PLUG
THREAD THREAD HEX HEX PARTSIZE A SIZE B L 1 2 NUMBER
1/4 NPT M16 x 2 49 19 19 686 319
PRESSURE GAUGE DIRECT CONNECTOR
THREAD HEX HEX PARTSIZE A L 1 2 NUMBER
1/4 NPT 54 19 19 686 074
THREAD HEX HEX PARTSIZE A L 1 2 NUMBER
1/4 BSPP 54 19 19 686 0721/2 BSPP 61.5 27 27 686 073
THREAD THREAD HEX HEX PARTSIZE A SIZE B L 1 2 NUMBER
1/4 BSPP M16 x 2 49 19 19 686 3061/2 BSPP M16 x 2 56 27 27 686 307
THREAD THREAD HEX HEX PARTSIZE A SIZE B L 1 2 NUMBER
1/4 BSPP M16 x 2 49 19 19 686 3081/2 BSPP M16 x 2 56 27 27 686 3091/4 NPT M16 x 2 49 19 19 686 310
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
123
MONITORING PLUG COUPLINGS
MONITORING PLUG TO METRIC PARALLEL
MONITORING PLUG TO NPT/BSPT
NPT TO BSPP GAUGE COUPLING
THREAD HEX PARTA L 2 NUMBER
M8x 1 26 11 686 000M10 x 1 26 12 686 003
MONITORING PLUGADAPTER
FOR CONNECTION TODIN FITTING
THREAD THREAD HEX PARTSIZE A SIZE B L 2 NUMBER
1/4 NPT 1/4 BSPP 32.2 19 686 950
TUBE THREAD HEX HEX PARTO.D. SIZE B L 1 2 NUMBER12L M18 x 1.5 41 11 22 686 02515L M22 x 1.5 41 11 27 686 02618L M26 x 1.5 44 11 32 686 02722L M30 x 2 46 11 36 686 02828L M36 x 2 46 11 41 686 02935L M45 x 2 52 11 50 686 03042L M52 x 2 55 11 60 686 031
12S M20 x 1.5 41 11 24 686 03214S M22 x 1.5 44 11 27 686 03316S M24 x 1.5 44 11 30 686 03420S M30 x 2 50 11 36 686 03525S M36 x 2 50 11 46 686 036
THREAD HEX PARTA L 2 NUMBER
M16x 2 75 19 686 070
THREAD HEX PARTA L 2 NUMBER
1/8 NPT 26 11 686 0011/8 BSPT 26 11 686 002
MONITORING PLUG TO MONITORING PLUG
*Washer Included
MON
ITOR
ING
PLUG
COUP
LING
S
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THREADED TESTPOINT COUPLINGS
THREADED TEST-POINT COUPLINGS
THREADED TEST-POINT TO METRIC PARALLEL
THREADED TEST-POINT TO BSPP
THREADED TEST-POINT TO SAE STRAIGHT THREAD
THREAD HEX PARTA L 2 NUMBER
M8x 1 45 19 686 200M10 x 1 39 14 686 215
M12 x 1.5 49 19 686 201M14 x 1.5 49 19 686 203M16 x 1.5 49 19 686 204
THREAD HEX PARTA L 2 NUMBER
1/8 NPT 49 19 686 2071/4 NPT 49 19 686 2081/2 NPT 49 19 686 222
THREAD HEX PARTA L 2 NUMBER
1/8 BSPP 49 19 686 2091/8 BSPP 49 19 686 205
THREAD HEX PARTA L 2 NUMBER
7/16 - 20 49 19 686 2069/16 - 18 49 19 686 214
THREADED TEST-POINT TO NPT THREADED TEST-POINT TO FEMALE JIC SWIV-
EL
124
THREAD HEX PARTA L 2 NUMBER
7/16 - 20 64 17 686 5001/2 - 20 66 17 686 501
9/16 - 18 68 17 686 5023/4 - 16 70 17 686 503
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THREADED TEST-POINT COUPLINGS
BULKHEAD CONNECTION THREADED TEST-POINT COUPLING TO THREADED TEST-POINT COUPLING
BULKHEAD CONNECTION THREADED TEST-POINT COUPLING TO JIC
BULKHEAD CONNECTION THREADED TEST-POINT COUPLING TO PLUG-IN TEST-POINT
THREAD HEX PARTA L 2 NUMBER
M16 x 2 73 19 686 305
THREAD HEX PARTA L 2 NUMBER
7/16 - 20 66 17 686 700
THREAD HEX PARTA L 2 NUMBER
M16 x 2 77 19 686 071
125
THRE
ADED
TES
TPO
INT
COUP
LING
S
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
THREADED TEST-POINT COUPLING TO METRIC STAND PIPE
THREADED TEST-POINT ADAPTER FOR CONNECTION TO DIN FITTING
D L L1 PART(mm) (mm) (mm) NUMBER
6 20 57 686 2258 20 57 686 226
10 20 57 686 22712 26 60 A.O.R.
TUBE THREAD HEX HEX PARTO.D. SIZE B L 1 2 NUMBER12L M18 x 1.5 58 19 22 686 23015L M22 x 1.5 58 19 27 686 23118L M26 x 1.5 61 19 32 686 23222L M30 x 2 63 19 36 686 23328L M36 x 2 63 19 41 686 23435L M45 x 2 69 19 50 686 23542L M52 x 2 72 19 60 686 236
12S M20 x 1.5 58 19 24 686 23714S M22 x 1.5 61 19 27 686 23816S M24 x 1.5 61 19 30 686 23920S M30 x 2 67 19 36 686 24025S M36 x 2 67 19 46 686 24130S M42 x 2 69 19 50 686 24238S M52 x 2 72 19 60 686 243
126
L
D
L1
THREADED TESTPOINT COUPLINGS
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
PRESSURE GAUGES
SERIES 63SPART RANGE NUMBER psi bar63S - 60 0 - 60 0 - 463S - 100 0 - 100 0 - 763S - 150 0 - 150 0 - 1063S - 300 0 - 300 0 - 2063S - 600 0 - 600 0 - 4063S - 800 0 - 800 0 - 5563S - 1000 0 - 1000 0 - 7063S - 1500 0 - 1500 0 - 10063S - 2000 0 - 2000 0 - 14063S - 3000 0 - 3000 0 - 21063S - 4500 0 - 4500 0 - 30063S - 6000 0 - 6000 0 - 420
PART RANGE NUMBER psi bar63R - 60 0 - 60 0 - 463R - 100 0 - 100 0 - 763R - 150 0 - 150 0 - 1063R - 300 0 - 300 0 - 2063R - 600 0 - 600 0 - 4063R - 800 0 - 800 0 - 5563R - 1000 0 - 1000 0 - 7063R - 1500 0 - 1500 0 - 10063R - 2000 0 - 2000 0 - 14063R - 3000 0 - 3000 0 - 21063R - 4500 0 - 4500 0 - 30063R - 6000 0 - 6000 0 - 420
PART RANGE NUMBER psi bar63FL - 60 0 - 60 0 - 463FL - 100 0 - 100 0 - 763FL - 150 0 - 150 0 - 1063FL - 300 0 - 300 0 - 2063FL - 600 0 - 600 0 - 4063FL - 800 0 - 800 0 - 5563FL - 1000 0 - 1000 0 - 7063FL - 1500 0 - 1500 0 - 10063FL - 2000 0 - 2000 0 - 14063FL - 3000 0 - 3000 0 - 21063FL - 4500 0 - 4500 0 - 30063FL - 6000 0 - 6000 0 - 420
AISI 304 stainless steelcase and bezel. Brassinternal parts. Gauges areglycerine filled and featurebuilt-in snubber to resistshock and pressuresurges. NPT 1/4" threadsare standard; BSP 1/4"threads are available.Accuracy: ± 1.6%.
SERIES 63R
Same quality features as63S except with center rearmount. NPT 1/4" threadsare standard; BSP 1/4"threads are available.Accuracy: ± 1.6%.
SERIES 63FL
Flanged center rear mountgauge for flush mounting.AISI 304 stainless steel caseand bezel. Brass internalparts. Gauges are glycerinefilled and feature built-insnubber to resist shock andpressure surges. NPT 1/4"threads are standard; BSP1/4" threads are available.Accuracy; ± 1.6%.
127
PRES
SURE
GA
UGES
Europower, Inc. 216-447-0898 Fax: 216-447-0933 www.europowerinc.com
PRESSURE GAUGES
SERIES 63SNPART RANGE NUMBER psi bar63SN - 60 0 - 60 0 - 463SN - 100 0 - 100 0 - 763SN - 150 0 - 150 0 - 1063SN - 300 0 - 300 0 - 2063SN - 600 0 - 600 0 - 4063SN - 800 0 - 800 0 - 5563SN - 1000 0 - 1000 0 - 7063SN - 1500 0 - 1500 0 - 10063SN - 2000 0 - 2000 0 - 14063SN - 3000 0 - 3000 0 - 21063SN - 4500 0 - 4500 0 - 30063SN - 6000 0 - 6000 0 - 420
PART RANGE NUMBER psi bar63RN - 60 0 - 60 0 - 463RN - 100 0 - 100 0 - 763RN - 150 0 - 150 0 - 1063RN - 300 0 - 300 0 - 2063RN - 600 0 - 600 0 - 4063RN - 800 0 - 800 0 - 5563RN - 1000 0 - 1000 0 - 7063RN - 1500 0 - 1500 0 - 10063RN - 2000 0 - 2000 0 - 14063RN - 3000 0 - 3000 0 - 21063RN - 4500 0 - 4500 0 - 30063RN - 6000 0 - 6000 0 - 420
PART RANGE NUMBER psi bar63U - 60 0 - 60 0 - 463U - 100 0 - 100 0 - 763U - 150 0 - 150 0 - 1063U - 300 0 - 300 0 - 2063U - 600 0 - 600 0 - 4063U - 800 0 - 800 0 - 5563U - 1000 0 - 1000 0 - 7063U - 1500 0 - 1500 0 - 10063U - 2000 0 - 2000 0 - 14063U - 3000 0 - 3000 0 - 21063U - 4500 0 - 4500 0 - 30063U - 6000 0 - 6000 0 - 420
Economy dry gauges withenameled black steel case,snap-in Plexiglas lens, andbrass stem. NPT 1/4"threads are standard; BSP1/4" threads are available.Accuracy: ± 1.6%.
SERIES 63RN
Same quality features as63SN except with centerrear mount. NPT 1/4"threads are standard; BSP1/4" threads are available.Accuracy: ± 1.6%.
SERIES 63U
U-clamp, center rear mountgauge for flush mounting.AISI 304 stainless steel caseand bezel. Brass internalparts. Gauges are glycerinefilled and feature built-insnubber to resist shock andpressure surges. NPT 1/4"threads are standard; BSP1/4" threads are available.Accuracy; ± 1.6%.
128
PRESSURE GAUGES