ev-adf5904sd2z user guide - analog devices · 3 c3, c4, c7 1000 pf capacitor murata...
TRANSCRIPT
EV-ADF5904SD2Z User GuideUG-791
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Board for the ADF5904 4-Channel, 24 GHz Receiver Downconverter
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 14
FEATURES Contains ADF5904 4-channel, 24 GHz receiver downconverter Accompanying software allows control of ADF5904 functions
from a PC
EVALUATION KIT CONTENTS EV-ADF5904SD2Z evaluation board
ADDITIONAL EQUIPMENT PC running Windows XP or more recent version Analog Devices, Inc., EVAL-SDP-CS1Z system demonstration
platform-serial (SDP-S) board Spectrum analyzer (optional) Oscilloscope 5 V power supplies USB cable
DOCUMENTS NEEDED ADF5904 data sheet
REQUIRED SOFTWARE Analog Devices ADF5904 Software
GENERAL DESCRIPTION The EV-ADF5904SD2Z evaluation board allows the user to evaluate the performance of the ADF5904 24 GHz receiver downconverter. Figure 1 shows the board, which contains the ADF5904, five high frequency SMA connectors for the local oscillator (LO) input, four receiver (Rx) inputs, eight SMA connectors for the baseband outputs, banana connectors for power supply, and a connector for serial interface.
The evaluation kit also contains software that is compatible with Windows® XP and later versions to allow easy programming of the device.
This evaluation board requires an EVAL-SDP-CS1Z SDP-S board (not supplied with the kit). The SDP-S board allows software programming of the ADF5904 device.
Full specifications on the ADF5904 are available in the product data sheet, which should be consulted in conjunction with this user guide when working with the evaluation board.
EVALUATION BOARD PHOTOGRAPH
Figure 1.
1289
5-00
1
UG-791 EV-ADF5904SD2Z User Guide
Rev. 0 | Page 2 of 14
TABLE OF CONTENTS Features .............................................................................................. 1
Evaluation Kit Contents ................................................................... 1
Additional Equipment ..................................................................... 1
Documents Needed .......................................................................... 1
Required Software ............................................................................ 1
General Description ......................................................................... 1
Evaluation Board Photograph ......................................................... 1
Revision History ............................................................................... 2
Quick Start Guide ............................................................................. 3
Evaluation Board Hardware ............................................................ 4
Power Supplies ...............................................................................4
Input Signals...................................................................................4
Output Signals ...............................................................................4
Default Operation .........................................................................4
Evaluation Board Software ...............................................................5
Evaluation and Test ...........................................................................7
Evaluation Board Schematics and Artwork ...................................8
Ordering Information .................................................................... 13
Bill of Materials ........................................................................... 13
Related Links ................................................................................... 13
REVISION HISTORY 3/15—Revision 0: Initial Version
EV-ADF5904SD2Z User Guide UG-791
QUICK START GUIDE Follow these steps to quickly evaluate the ADF5904.
1. Connect the power supply to the EV-ADF5904SD2Z:a. 5 V to Banana Connector P2b. GND to Banana Connector P1
2. Install the ADF5904 software.3. Connect the SDP-S motherboard to the PC and to the
EV-ADF5904SD2Z evaluation board.4. Follow the hardware driver installation procedure.5. Run the ADF5904 software.6. Select the ADF5904 device and the USB board in the
Select Device and Connection tab of the software frontpanel window (see Figure 2).
7. Check that the message SDP board connected appears atthe bottom left of the software window (see Figure 2).
8. Connect an ac-coupled RF source to LOIN SMA andconnect an ac-coupled RF source to one of the RXxINinput SMAs.
9. In the Main Controls tab, click Initialize.10. Connect the corresponding Rx baseband channel output to
an oscilloscope.11. Measure the results.
Rev. 0 | Page 3 of 14
UG-791 EV-ADF5904SD2Z User Guide
EVALUATION BOARD HARDWARE The evaluation board requires an SDP-S motherboard to program the device. The SDP-S board is not included and must be purchased separately. The EV-ADF5904SD2Z schematics are shown in Figure 5 to Figure 9. The top layer and assembly layout are shown in Figure 10.
POWER SUPPLIES The evaluation board is powered via one external supply, 5 V connected as described in the Quick Start Guide section.
INPUT SIGNALS The LO input pin and the Rx input pins on the ADF5904 contain a dc bias voltage; the inputs must be ac-coupled to the evaluation board.
OUTPUT SIGNALS The baseband outputs from the ADF5904 contain dc bias voltages and are available on the J3 to J11 output SMAs.
Table 1. Baseband Output Mapping Rx Input Baseband Outputs RF1IN J3, J4 RF2IN J6, J7 RF3IN J8, J9 RF4IN J10, J11
DEFAULT OPERATION All components necessary for ADF5904 operation are inserted on the board.
Rev. 0 | Page 4 of 14
EV-ADF5904SD2Z User Guide UG-791
Rev. 0 | Page 5 of 14
EVALUATION BOARD SOFTWARE The control software for the EV-ADF5904SD2Z is included in the evaluation kit on a CD. To install the software, follow the on-screen instructions.
To run the software, click the ADF5904 file on the desktop or from the Start menu.
In the Select Device and Connection tab, select the device and the connection method, and click Connect.
Confirm that Analog Devices Eval Board connected is displayed at the bottom left of the window (see Figure 2). Otherwise, the software has no connection to the evaluation board.
Note that, when connecting the board, it takes approximately 5 sec to 10 sec for the status label to change.
Figure 2. Software Front Panel Display—Select Device and Connection
12
895-
002
UG-791 EV-ADF5904SD2Z User Guide
Rev. 0 | Page 6 of 14
The Main Controls tab controls the ADF5904 device settings (see Figure 3).
This tab allows the user to select general options available for the ADF5904, including power up/down control and register readback.
On initial power-up of the device, click the Initialize button to perform the initialization sequence as described in the ADF5904 data sheet.
Figure 3. Software Front Panel Display—Main Controls
1289
5-00
3
EV-ADF5904SD2Z User Guide UG-791
Rev. 0 | Page 7 of 14
EVALUATION AND TEST To evaluate and test the performance of the ADF5904, take the following steps:
1. Install the SDP-S software drivers. Connect the evaluation board to a PC using the supplied USB cable. Follow the hardware driver installation procedure that appears.
2. Connect the SDP-S connector to the EV-ADF5904SD2Z. 3. Install the ADF5904 software. 4. Connect an ac-coupled RF signal to LOIN SMA. 5. Connect an ac-coupled RF signal to the RX1IN input SMA.
6. Connect a 1 MΩ, ac-coupled oscilloscope to the J3 and J4 output SMAs.
7. Run the ADF5904 software. 8. Select the SDP-S board and the ADF5904 device in the
Select Device and Connection tab of the software window. 9. In the Main Controls tab, click Initialize to power up the
ADF5904 (see Figure 3). See Figure 4 for the suggested setup.
10. Measure the baseband output signals.
Figure 4. Typical Evaluation Setup
PC
POWERSUPPLY
SIGNALSOURCE
SIGNALSOURCE
OSCILLOSCOPE
+5V
DC BLOCK
SDP-SADAPTOR
BOARD
1289
5-00
4
UG-791 EV-ADF5904SD2Z User Guide
EVALUATION BOARD SCHEMATICS AND ARTWORK
Figure 5. Evaluation Board Schematic (Page 1)
RX3_RF
RF1IN
RX3_BBOB
J2
LOIN1
2 3
RF3IN1
2 3
0 0
TP4
TP3
TP2
TP1
J4
J6
J7
J8
J9
J10
J11
J3
R3
32
1RF2IN
RX1_BBO
RX2_BBO
RX2_BBO
RX1_BBOB
RX3_BBO
RX4_BBO
RX4_BBOB
RX4_BBOBRX4_BBO
RX1_BBO
DOUT
CE
DATA
CLK
AVDD
RX2_BBOB
RX3_BBOB
0
1
2 3
LO_IN
RX4_RF
RX2_RF
RX3_BBO
RX2_BBOB
RX1_RF
RF4IN
LE
R2
R1
RX1_BBOB
BLOCK2
LO_RFIN
RX4_RFIN
RX3_RFIN
RX2_RFIN
RX1_RFIN
LE
CLK
DATA
CE
DOUT
RX1
2_A
HI
RX3
4_A
HI
LO_A
HI
RX1_BBORX1_BBOB
RX2_BBORX2_BBOB
RX3_BBORX3_BBOB
RX4_BBORX4_BBOB
ATEST
J1
P2
P1
AVDD
AGNDPOWER
AVDD1
VDD AVDD
DOUT
LE
CLK
CE
DATA
AVDD
INTERFACE
CLK
DOUTCELE
DATA
AVD
D
1289
5-00
5
Rev. 0 | Page 8 of 14
EV-ADF5904SD2Z User Guide UG-791
Figure 6. Evaluation Board Schematic (Page 2)
1TP6
1TP7
1TP8
1TP9
1TP5
R16
R13
R17
R19
R20
R18
R12
R14
R15
R10
R8
R9R
11
R4
390
DATADOUT
LE
330
8.2K
10K
AVD
D
330
330
390
390
390
10K
0330
0 0
CE
CLK
IOIOIO
IO
IO
IO
DGND
DGND
SDP-S
SPI_MOSISPI_MISO
SPI_SEL_BSPI_SEL_C
SPI_CLK
SPI_SEL_AGPIO7GPIO6GPIO5GPIO4GPIO3GPIO2GPIO1GPIO0
1289
5-00
6
Rev. 0 | Page 9 of 14
UG-791 EV-ADF5904SD2Z User Guide
Figure 7. Evaluation Board Schematic (Page 3)
EE
PR
OM
616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120
J5
7
48
56321
U3
R6 R7
R5
605958575655545352515049484746454443424140393837363534333231302928272625242322212019181716151413121110987654321J5
SPI_SEL_A
GPIO1GPIO3
GPIO5GPIO7
SPI_MOSISPI_MISOSPI_CLK
FX8-
120S
-SV
(21)
GPIO2GPIO4
VIO
100K
100K
FX8-
120S
-SV
(21)
24LC
32A
-I/M
S
TBD0603
SPI_SEL_BSPI_SEL_C
GPIO0
GPIO6
IOIO
IOIO
IOIOIOIO
IO
IOIOIO
IOIO
VS
S
VC
C
WP
A2
A1
A0
SC
LS
DA
DG
ND
DG
ND
12895-007
Rev. 0 | Page 10 of 14
EV-ADF5904SD2Z User Guide UG-791
Figure 8. Evaluation Board Schematic (Page 4)
Figure 9. Evaluation Board Schematic (Page 5)
L1A C
D2
AC
D1 C11
C10
C12
R25R21
R26
R24
R23
R22
1827
PAD
46 35
U2
VDD
MBR0540T1G4.7UH
1UF
0
1UF
ADP7104
1UF
0
AVDD1
AVDD
0
0
0
1N40
01
0
IO
IO
AGND
IO
AGNDAGNDAGNDAGNDAGND
SENSE
PAD
VINPGGNDEN NC
GND
VOUT
1289
5-00
8
PAD
32 31 30 29 28 27 26 2524
23
22
21
20
19
18
17
16151413121110
9
8
7
6
5
4
3
2
1
U1C8C7C6
C5
C3
C9
C4
C1
C2
RX1_RFIN
LO_R
FIN
RX1
_BB
O
RX1
_BB
OB
RX2_BBO
RX3_RFIN
RX34_AHI
RX4_BBOB
10PF100PF1000PF
10PF100PF
10PF100PF
1000PF
1000PF
RX12_AHI
LO_AHI
RX34_AHI
ADF5904
CE
DO
UT
ATE
ST
RX4
_BB
O
DA
TA
CLKLE
RX2
_BB
OB
RX4_RFIN
RX3
_BB
O
RX3
_BB
OB
LO_A
HI
RX2_RFIN
RX12_AHI
AGND
AGND
INININ IN IN IN IN ININ
IN
IN
IN
ININININININ
IN
IN
IN
IN
AGND
AGND
1289
5-00
9
Rev. 0 | Page 11 of 14
UG-791 EV-ADF5904SD2Z User Guide
Figure 10. Layer 1 (Component Side)
1289
5-01
0
Rev. 0 | Page 12 of 14
EV-ADF5904SD2Z User Guide UG-791
Rev. 0 | Page 13 of 14
ORDERING INFORMATION BILL OF MATERIALS
Table 2. Qty Reference Designator Description Manufacturer Part Number 3 C1, C2, C6 0.1 μF capacitor AVX 06033C104JAT2A 3 C3, C4, C7 1000 pF capacitor Murata GRM1555C1H102JA01 3 C5, C8, C9 10 pF capacitor AVX 04025U100GAT2A 1 D1 Diode Multicomp 1N4001 1 D2 Diode On Semiconductor MBR0520LT1G 10 J1 to J4, J6 to J11 Connector, PCB, end launch, SMA Emerson 142-0701-851 1 J5 120-way connector, 0.6 mm pitch Hirose FX8-120S-SV(21) 1 L1 4.7 μH inductor Coilcraft EPL2014-472ML 5 LOIN, RF1IN to RF4IN 2.92 mm Rosenberger connectors Rosenberger 02K243-40M 1 P1 Black, 4 mm, banana socket Deltron 571-0100 1 P2 Red, 4 mm, banana socket Deltron 571-0500 3 R4, R8, R10 330 Ω resistor Vishay CRCW0603330RFKEA 4 R11, R12, R14, R15 390 Ω resistor Multicomp MC 0.063W 0603 390R 1 R17 10 kΩ resistor Multicomp MC 0.063W 0603 10K 1 R19 8.2kΩ resistor Multicomp MC 0.063W 0603 1% 8K2 1 R20 10 kΩ resistor Multicomp MC 0.063W 0603 10K 2 R5,R7 100 kΩ resistor Yageo (Phycomp) RC0402JR-07100KL 1 R6 Do not populate Not applicable Not applicable 9 TP1 to TP9 Connector, PCB, test point, red Keystone Electronics Corp 5000 1 U2 Linear regulator, 3.3 V, 20 V, 500 mA, ultralow noise Analog Devices ADP7104ARDZ-3.3 1 U3 32k, I2C, serial EEPROM, MSOP8 Microchip 24LC32A-I/MS 2 Screw1, Screw2 Screw, cheese, nylon Allthread 119030010 2 Nut1, Nut2 Nut/washer, nylon Duratool 1140030 1 U1 ADF5904 Rx MMIC Analog Devices ADF5904BCPZ 4 R21, R22, R25, R26 0 Ω resistor Multicomp MC 0.0625W 0402 1% 0R 1 R24 0.33 Ω resistor Welwyn LRCS0402-0R33FT5 1 R23 Do not populate Not applicable Not applicable 1 C12 100 μF capacitor Kemet T520B107M006ATE040 1 C11 10 μF capacitor Murata GRM21BR61A106KE19L 1 C10 1 μF capacitor Taiyo/Yuden TMK107BJ105KA-T 1 R16 Do not populate Not applicable Not applicable 1 R9 Do not populate Not applicable Not applicable 5 R1, R2, R3, R13, R18 0 Ω resistor Multicomp MC 0.063W 0603 0R
RELATED LINKS Resource Description ADF5904 Product Page, 4-Channel, 24 GHz, Receiver Downconverter ADP7104 Product Page, 20 V, 500 mA, Low Noise, CMOS LDO
UG-791 EV-ADF5904SD2Z User Guide
Rev. 0 | Page 14 of 14
NOTES
ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG12895-0-3/15(0)