explosion proof. - velkommen til lauridsen industri · explosion proof. safety for all control...

Explosion proof.Safety for all Control Systems.

Price list 2008valid from 1. April 2008

www.sch ischek .com

www.schischek.com

Price list 2008

Which componentshave to be explosion proof ?

Actuators for air technology

Measurement and control

Actuators for liquids

In the diagram below, a typical air-handling system

shows which equipment is allowed in the Ex area and

which should only be placed in the safe area. The

diagram does not enforce the claim to be complete. If in

doubt, please do not hesitate to consult us at Schischek.

We will advise you in any case. A brief discussion in the

early stages of planning can avoid substantial costs in

remedial work later and gives you the peace of mind

that you have a safely installed operating system.

You should be aware of the areas of installation where

an explosive atmosphere may build up.

Furthermore, you should have the responsible authority

classify the relevant Ex zone and in combination with

type and condition of the explosive medium, you should

be able to select suitable explosion proof equipment.

With Schischek products this is simple because all

equipment is certified according to the highest safety

standards – according to ATEX, of course !

Price list 2008

www.schischek.com

Table of contents

gas dust gas dust gas dustProduct series page 0 20 1 21 2 22 SA* Ex - quarter turn actuators 90° ExMax size „S“ 5… 30 Nm with /without spring return 04

ExMax size „M“ 30… 100 Nm with /without spring return 05

RedMax size „S“ 5… 30 Nm with /without spring return 06

RedMax size „M“ 30… 100 Nm with /without spring return 07

InMax size „S“ 5… 30 Nm with /without spring return (not Ex) 08

InMax size „M“ 30… 100 Nm with /without spring return (not Ex) 09

Ex - valve actuators 5...60 mm stroke ExRun size „S“ 500… 10.000 N without spring return 10

RedRun size „S“ 500… 10.000 N without spring return 10

InRun size „S“ 500… 10.000 N without spring return (not Ex) 10-11

Ex - long stroke linear motion actuators 100...300 mm strokeExPlus 300… 3.000 N without spring return 12

RedPlus 300… 3.000 N without spring return 12

InPlus 300… 3.000 N without spring return (not Ex) 12-13

Ex - sensors, modulating (temperature, humidity, pressure) Overview sensors 14ExCon-P differential pressure, VAV sensors ± 100… 7.500 Pa 15 RedCon-P differential pressure, VAV sensors ± 100… 7.500 Pa 15

InCon-P differential pressure, VAV sensors ± 100… 7.500 Pa (not Ex) 15

ExCon-D temperature- and humidity transducer for ExPro sensors 16

RedCon-D temperature- and humidity transducer for ExPro sensors 16

InCon-D temperature- and humidity transducer for InPro sensors (not Ex) 16

ExPro temperature- and humidity sensors for HVAC-systems 17

InPro temperature- and humidity sensors for HVAC-systems (not Ex) 17

ExCon-A transducer for passive, potential free, modulating ExSens sensors 18

RedCon-A transducer for passive, potential free, modulating ExSens sensors 18

InCon-A transducer for passive, potential free, modulating ExSens sensors (not Ex) 18

ExLine transducer for passive, potential free, modulating ExSens sensors 19

ExSens modulating, passive temperature- /humidity- /pressure sensors 19 () () ()

Ex - sensors, binary (temperature, humidity, pressure) ExLine switching module for passive, potential free, binary ExSens sensors 20

ExSens binary, passive temperature- /humidity- /pressure sensors 20 () () ()

Ex - door holder magnets ExMag, door holder magnets with 650, 1.300, 2.000 N force 21

Ex - components ExComp different Ex-components, e.g. switches, buttons, … 21

General terms and conditions 22

Explosion Proof according to ATEX 94/9/EC Legal bases and basic information 23Selection table Ex-nomenclature 24Basics 25-26Applications 27

*SA = Safe area() = on request

Installation areas in zone

Price list 2008

www.schischek.com

Prices in EUR/unit, ex work, plus packing and VAT. Payment 10 days 2% or 30 days net. Our general conditions of page 22 are applicable.

ExMax 90° Ex quarter turn actuators size „S“ for zone 1, 2, 21, 22

ExMax- ... Explosion proof zone 1, 2, 21, 22 gas + dust PTB-certifiedII2G EEx d ia IIC T6

II2D IP66 T80°CATEX 94/9/EG

IEC-Ex

Basics for all ExMax-.. size „S“24…230 VAC/DC self adaptable power supplyUp to 5 different running times adjustable on site95°angle of rotation (5° for pretention), 100% overload protected, aluminium housing IP 66, cable ~ 1 m-40...+40°C/+50°C, integrated heater, Simple manual overrideSquared shaft connection 12 × 12 mmDimensions (L × W × D) 210 × 95 × 80 mm

DescriptionExMax are, in acc. with type, for automation of air dampers, fire and smoke dampers, volume control, as well as for ball valves, throttle valves and other quarter turn armatures.

Delivery: 1 actuator, ~ 1 m cable, allen key for manual override, 4 screws.

Size „S“

ExMax - 5.10 5 Nm / 10 Nm 3/15/30/60/120 sec. - On-off, 3-pos - - SExMax - 15.30 15 Nm / 30 Nm 3/15/30/60/120 sec. - On-off, 3-pos - - SExMax - 5.10 - S 5 Nm / 10 Nm 3/15/30/60/120 sec. - On-off, 3-pos - 2 x EPU (2 aux. switches @ 5° and 85°) SExMax - 15.30 - S 15 Nm / 30 Nm 3/15/30/60/120 sec. - On-off, 3-pos - 2 x EPU (2 aux. switches @ 5° and 85°) SExMax - 5.10 - Y 5 Nm / 10 Nm 7,5/15/30/60/120 sec. - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - SExMax - 15.30 - Y 15 Nm / 30 Nm 7,5/15/30/60/120 sec. - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S

Type Torque Running time 90° Spring return Control mode Feedback Features Size

Ex-d quarter turn actuators without spring return, 24 to 230 VAC/DC

ExMax - 5.10 - F 5 Nm / 10 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - - SExMax - 15 - F 15 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - - SExMax - 5.10 - SF 5 Nm / 10 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) SExMax - 15 - SF 15 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) SExMax - 5.10 - YF 5 Nm / 10 Nm 7,5/15/30/60/120 sec. ~ 3 sec. / 10 sec. 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - SExMax - 15 - YF 15 Nm 7,5/15/30/60/120 sec. ~ 3 sec. / 10 sec. 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - SExMax - 5.10 - BF 5 Nm / 10 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - Ex-i FireSafe connector + 2 x EPU (s.o.) SExMax - 15 - BF 15 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - Ex-i FireSafe connector + 2 x EPU (s.o.) S


Ex-d quarter turn actuators with spring return, 24 to 230 VAC/DC

ExMax - 15 - F3 15Nm 3/15/30/60/120sec. ≤3sec. On-off - - SExMax - 15 - SF3 15Nm 3/15/30/60/120sec. ≤3sec. On-off - 2xEPU(=2aux.switches@5°and85°) SExMax - 15 - BF3 15Nm 3/15/30/60/120sec. ≤3sec. On-off - Ex-iFireSafeconnector+2xEPU(s.o.) S


Ex-d quarter turn actuators with 3 sec. spring return for Offshore application, 24 to 230 VAC/DC

ExMax-…VAS Size „S“, housing material in stainless steel AISI 316, some parts nickel platedExMax-…CTS Size „S“, aluminium housing Amercoat painted, resistant against corrosive and/or maritime atmosphere, some parts nickel plated ExSwitch 2 external, adaptable, on site adjustable Ex-aux. switches with 2 potentail free contacts, adaptable to ExMax-... actuatorsExBox-3P Ex-e terminal box connectable to ExMax-... actuators with 1 cable for On-off or 3-pos operation ExBox-3P/SW Ex-e terminal box connectable to ExMax-... actuators with 1 cable for On-off or 3-pos operation + 2 cable for external aux. switches type ExSwitchExBox-Y/S Ex-e terminal box connectable to ExMax-... actuators with 2 cable, for modulating operation or 3-pos + integr. switches (HS)ExBox-Y/S/SW Ex-e terminal box connectable to ExMax-... actuators with 2 cable, for modulating or 3-pos operation with feedback signal + 2 cable for external aux. switchesExBox-BF Ex-e terminal box connectable to ExMax-... actuators with 1 cable, for all ExMax-...-BFExBox-…/VA Ex-e terminal-box, housing made of stainless-steel type AISI 316 L, some parts nickel plated, surcharge on aluminium versionExBox-…/CT Ex-e terminal-box, housing AMERCOAT painted, resistant against corrosive and/or maritime atmosphere, some parts nickel plated, surcharge on aluminium versionMKK-S Mounting bracket for …Box-terminal boxes for direct coupling to …Max... actuators size „S“MKK-S/VA Mounting bracket, made of stainless-steel suitable for ExBox...VAKB-S Mounting clamp for round damper shaft Ø 10 to 20 mm and squared shafts 10 to 16 mm, incl. bracket, connectable to all ExMax-... size „S“HV-SK, HV-SL Manual override, connectable to …Max-... actuators size „S“. HV-SK=short version, HV-SL=long version for add. mounting of ...Box/SwitchAR-12-xx Squared reduction part from 12x12 mm to shafts with 11mm (type AR-12-11), 10 mm (type AR-12-10), 8 mm (type AR-12-08)D-F-…S Adaptation with flange acc. to DIN EN 5211 for butterfly or ball-valves suitable for size „S“FireSafe Safety temperature trigger for fire dampers, switching at 72°C, with electrical connector, only connectable to …Max-…-BF actuators !

Type Technical data

Accessories (additional price)

Explosion proof Features of ExMax - ... size „S“

EUR/unit 599,– 699,– 649,– 749,– 699,– 799,–

EUR/unit 729,– 829,– 779,– 879,– 829,– 929,– on requ.on requ.

EUR/unit 949,– 999,– on requ.

EUR/unit 499,– 199,– 199,– 69,– 79,– 89,– 99,– 99,– 179,– 89,– 14,– 24,– 49,– 69,– 9,– on requ. 99,–

Price list 2008

www.schischek.com


ExMax 90° Ex quarter turn actuators size „M“ for zone 1, 2, 21, 22

ExMax- ... Explosion proof zone 1, 2, 21, 22 gas + dust PTB-certifiedII2G EEx d ia IIC T6

II2D IP66 T80°CATEX 94/9/EC

Basics for all ExMax-.. size „M“24…230 VAC/DC self adaptable power supplyUp to 5 different running times adjustable on site95°angle of rotation (5° for pretention), 100% overload protected, aluminium housing IP 66, cable ~ 1 m-40...+40°C/+50°C, integrated heater, Simple manual overrideSquared shaft connection 16 × 16 mmDimensions (L × W × D) 287 × 149 × 116 mm

DescriptionExMax are, in acc. with type, for automation of air dampers, fire and smoke dampers, volume control, as well as for ball valves, throttle valves and other quarter turn armatures.


Size „M“

ExMax - 50.75 50 Nm / 75 Nm 40/60/90/120/150 sec. - On-off, 3-pos - - MExMax - 100 100 Nm 40/60/90/120/150 sec. - On-off, 3-pos - - MExMax - 50.75 - S 50 Nm / 75 Nm 40/60/90/120/150 sec. - On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° at 85°) MExMax - 100 - S 100 Nm 40/60/90/120/150 sec. - On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° at 85°) MExMax - 50.75 - Y 50 Nm / 75 Nm 40/60/90/120/150 sec. - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - MExMax - 100 - Y 100 Nm 40/60/90/120/150 sec. - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - M


Ex-d quarter turn actuators without spring return, 24 to 230 VAC/DC

ExMax - 30 - F 30 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - - MExMax - 50 - F 50 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - - MExMax - 30 - SF 30 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° at 85°) MExMax - 50 - SF 50 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° at 85°) MExMax - 30 - YF 30 Nm 40/60/90/120/150 sec. ~20 sec. 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - MExMax - 50 - YF 50 Nm 40/60/90/120/150 sec. ~20 sec. 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - MExMax - 30 - BF 30 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - Ex-i FireSafe connector + 2 x EPU (s.o.) MExMax - 50 - BF 50 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - Ex-i FireSafe connector + 2 x EPU (s.o.) M


Ex-d quarter turn actuators with spring return, 24 to 230 VAC/DC

ExMax - 30 - F3 30Nm 40/60/90/120/150sec. ≤3sec. On-off - - MExMax - 50 - F3 50Nm 40/60/90/120/150sec. ≤3sec. On-off - - MExMax - 30 - SF3 30Nm 40/60/90/120/150sec. ≤3sec. On-off - 2xEPU(=2aux.switches@5°at85°) MExMax - 50 - SF3 50Nm 40/60/90/120/150sec. ≤3sec. On-off - 2xEPU(=2aux.switches@5°at85°) MExMax - 30 - BF3 30Nm 40/60/90/120/150sec. ≤3sec. On-off - Ex-iFireSafeconnector+2xEPU(s.o.) MExMax - 50 - BF3 50Nm 40/60/90/120/150sec. ≤3sec. On-off - Ex-iFireSafeconnector+2xEPU(s.o.) M


Ex-d quarter turn actuators with 3 sec. spring return for Offshore application, 24 to 230 VAC/DC

Explosion proof Features of ExMax - ... size „M“

ExMax-...-CTM Size „M“, aluminium housing Amercoat painted, resistant against corrosive and/or maritime atmosphere, some parts nickel platedExSwitch 2 external, adaptable, on site adjustable Ex-aux. switches with 2 potentail free contacts, adaptable to ExMax-... actuatorsExBox-3P Ex-e terminal box connectable to ExMax-…actuators with 1 cable for On-off or 3-pos operationExBox-3P/SW Ex-e terminal box connectable to ExMax-…actuators with 1 cable for On-off or 3-pos operation + 2 cable for external aux. switches type ExSwitch ExBox-Y/S Ex-e terminal box connectable to ExMax-... actuators with 2 cable, for modulating operation or 3-pos + integr. switches (HS)ExBox-Y/S/SW Ex-e terminal box connectable to ExMax-…actuators with 2 cable, for modulating or 3-pos operation with feedback signal + 2 cable for external aux. switchesExBox-BF Ex-e terminal box connectable to ExMax-…actuators with 1 cable, for all ExMax-...-BFExBox-…/CT Ex-e terminal-box, housing AMERCOAT painted, resistant against corrosive and/or maritime atmosphere, some parts nickel plated, surcharge on aluminium versionMKK-M Mounting bracket for …Box-terminal boxes for direct coupling to …Max... actuators size „M“ HV-MK, HV-ML Manual override, connectable to …Max-…actuators size „M“. HV-MK=short version, HV-ML=long version for add. mounting of ...Box/Switch AR-16-xx Squared reduction part from 16x16 mm to shafts with 14mm (type AR-16-14), 12 mm (type AR-16-12) D-F-…M Adaptation with flange acc. to DIN EN 5211 for butterfly or ball-valves suitable for size „M“ FireSafe Safety temperature trigger for fire dampers, switching at 72°C, with electrical connector, only connectable to …Max-…-BF actuators !

Type Technical data


EUR/unit 899,– 1.099,– 949,– 1.149,– 1.099,– 1.299,–

EUR/unit 1.199,– 1.399,– 1.249,– 1.449,– 1.399,– 1.599,–on requ. on requ.

EUR/unit 1.499,– 1.699,– 1.549,– 1.749,– on requ. on requ.

EUR/unit 299,– 199,– 69,– 79,– 89,– 99,– 99,– 89,– 20,– 89,– 18,– on requ. 99,–

Price list 2008

www.schischek.com


RedMax 90° Ex quarter turn actuators „S“ for zone 2, 22

RedMax- ... Explosion proof zone 2, 22 gas + dust PTB-certified

II3G EEx nC II T6II3(1)G EEx [ia] IICII3D IP66 T80°CATEX 94/9/EC

Basics for all RedMax-.. size „S“24…230 VAC/DC self adaptable power supplyUp to 5 different running times adjustable on site95°angle of rotation (5° for pretention), 100% overload protected, aluminium housing IP 66, cable ~ 1 m-40...+40°C/+50°C, integrated heater, Simple manual overrideSquared shaft connection 12 × 12 mmDimensions (L × W × D) 210 × 95 × 80 mm

DescriptionRedMax are, in acc. with type, for automation of air dampers, fire and smoke dampers, volume control, as well as for ball valves, throttle valves and other quarter turn armatures.


Size „S“

RedMax - 5.10 5 Nm / 10 Nm 3/15/30/60/120 sec. - On-off, 3-pos - - S RedMax - 15.30 15 Nm / 30 Nm 3/15/30/60/120 sec. - On-off, 3-pos - - S RedMax - 5.10 - S 5 Nm / 10 Nm 3/15/30/60/120 sec. - On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) S RedMax - 15.30 - S 15 Nm / 30 Nm 3/15/30/60/120 sec. - On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) S RedMax - 5.10 - Y 5 Nm / 10 Nm 7,5/15/30/60/120 sec. - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S RedMax - 15.30 - Y 15 Nm / 30 Nm 7,5/15/30/60/120 sec. - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S


Ex-n quarter turn actuators without spring return, 24 to 230 VAC/DC

RedMax - 5.10 - F 5 Nm / 10 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - - S RedMax - 15 - F 15 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - - S RedMax - 5.10 - SF 5 Nm / 10 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) S RedMax - 15 - SF 15 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) S RedMax - 5.10 - YF 5 Nm / 10 Nm 7,5/15/30/60/120 sec. ~ 3 sec. / 10 sec. 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S RedMax - 15 - YF 15 Nm 7,5/15/30/60/120 sec. ~ 3 sec. / 10 sec. 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S RedMax - 5.10 - BF 5 Nm / 10 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - Ex-i FireSafe connector + 2 x EPU (s.o.) SRedMax - 15 - BF 15 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - Ex-i FireSafe connector + 2 x EPU (s.o.) S


Ex-n quarter turn actuators with spring return, 24 to 230 VAC/DC

RedMax - 15 - F3 15Nm 3/15/30/60/120sec. ≤3sec. On-off - - SRedMax - 15 - SF3 15Nm 3/15/30/60/120sec. ≤3sec. On-off - 2xEPU(=2aux.switches@5°and85°) SRedMax - 15 - BF3 15Nm 3/15/30/60/120sec. ≤3sec. On-off - Ex-iFireSafeconnector+2xEPU(s.o.) S


Ex-n quarter turn actuators with 3 sec. spring return for Offshore application, 24 to 230 VAC/DC

Explosion proof Features of RedMax - ... size „S“

RedMax-...-VAS Size „S“, housing material in stainless steel AISI 316, some parts nickel plated RedMax-...-CTS Size „S“, aluminium housing Amercoat painted, resistant against corrosive and/or maritime atmosphere, some parts nickel plated RedSwitch 2 external, adaptable, on site adjustable Ex-aux. switches with 2 potentail free contacts, adaptable to RedMax-... actuators RedBox-3P Ex-e terminal box connectable to RedMax-…actuators with 1 cable for On-off or 3-pos operation RedBox-3P/SW Ex-e terminal box connectable to RedMax-…actuators with 1 cable for On-off or 3-pos operation + 2 cable for external aux. switches type RedSwitch RedBox-Y/S Ex-e terminal box connectable to RedMax-... actuators with 2 cable, for modulating operation or 3-pos + integr. switches (HS) RedBox-Y/S/SW Ex-e terminal box connectable to RedMax-…actuators with 2 cable, for modulating or 3-pos operation with feedback signal + 2 cable for external aux. switches RedBox-BF Ex-e terminal box connectable to RedMax-…actuators with 1 cable, for all RedMax-…-BF RedBox-…/VA Ex-e terminal-box, housing made of stainless-steel type AISI 316 L, some parts nickel plated, surcharge on aluminium version RedBox-…/CT Ex-e terminal-box, housing AMERCOAT painted, resistant against corrosive and/or maritime atmosphere, some parts nickel plated, surcharge on aluminium version MKK-S Mounting bracket for …Box-terminal boxes for direct coupling to …Max... actuators size „S“ MKK-S/VA Mounting bracket, made of stainless-steel suitable for …Box/VA KB-S Mounting clamp for round damper shaft Ø 10 to 20 mm and squared shafts 10 to 16 mm, incl. bracket, connectable to all RedMax-… size „S“ HV-SK, HV-SL Manual override, connectable to …Max-... actuators size „S“. HV-SK=short version, HV-SL=long version for add. mounting of ...Box/Switch AR-12-xx Squared reduction part from 12x12 mm to shafts with 11mm (type AR-12-11), 10 mm (type AR-12-10), 8 mm (type AR-12-08) D-F-…S Adaptation with flange acc. to DIN EN 5211 for butterfly or ball-valves suitable for size „S“ FireSafe Safety temperature trigger for fire dampers, switching at 72°C, with electrical connector, only connectable to …Max-…-BF actuators !

Type Technical data


EUR/unit 499,– 599,– 549,– 649,– 599,– 699,–

EUR/unit 629,– 729,– 679,– 779,– 729,– 829,–on requ.on requ.

EUR/unit 849,– 899,–on requ.

EUR/unit 499,– 199,– 159,– 59,– 69,– 79,– 89,– 89,– 179,– 89,– 14,– 24,– 49,– 69,– 9,– on requ. 99,–

Price list 2008

www.schischek.com


RedMax 90° Ex quarter turn actuators „M“ for zone 2, 22

RedMax- ... Explosion proof zone 2, 22 gas + dust PTB-certified

II3G EEx nC II T6II3(1)G EEx [ia] IICII3D IP66 T80°CATEX 94/9/EC

Basics for all RedMax-.. size „M“24…230 VAC/DC self adaptable power supplyUp to 5 different running times adjustable on site95°angle of rotation (5° for pretention), 100% overload protected, aluminium housing IP 66, cable ~ 1 m-40...+40°C/+50°C, integrated heater, Simple manual overrideSquared shaft connection 16 × 16 mmDimensions (L × W × D) 287 × 149 × 116 mm

DescriptionRedMax are, in acc. with type, for automation of air dampers, fire and smoke dampers, volume control, as well as for ball valves, throttle valves and other quarter turn armatures.


Size „M“

RedMax - 50.75 50 Nm / 75 Nm 40/60/90/120/150 sec. - On-off, 3-pos - - M RedMax - 100 100 Nm 40/60/90/120/150 sec. - On-off, 3-pos - - M RedMax - 50.75 - S 50 Nm / 75 Nm 40/60/90/120/150 sec. - On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) M RedMax - 100 - S 100 Nm 40/60/90/120/150 sec. - On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) M RedMax - 50.75 - Y 50 Nm / 75 Nm 40/60/90/120/150 sec. - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - M RedMax - 100 - Y 100 Nm 40/60/90/120/150 sec. - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - M


Ex-n quarter turn actuators without spring return, 24 to 230 VAC/DC

RedMax - 30 - F 30 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - - M RedMax - 50 - F 50 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - - M RedMax - 30 - SF 30 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) M RedMax - 50 - SF 50 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) M RedMax - 30 - YF 30 Nm 40/60/90/120/150 sec. ~20 sec. 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - M RedMax - 50 - YF 50 Nm 40/60/90/120/150 sec. ~20 sec. 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - M RedMax - 30 - BF 30 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - Ex-i FireSafe connector + 2 x EPU (s.o.) M RedMax - 50 - BF 50 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - Ex-i FireSafe connector + 2 x EPU (s.o.) M


Ex-n quarter turn actuators with spring return, 24 to 230 VAC/DC

RedMax - 30 - F3 30Nm 40/60/90/120/150sec. ≤3sec. On-off - - MRedMax - 50 - F3 50Nm 40/60/90/120/150sec. ≤3sec. On-off - - MRedMax - 30 - SF3 30Nm 40/60/90/120/150sec. ≤3sec. On-off - 2xEPU(=2aux.switches@5°and85°) MRedMax - 50 - SF3 50Nm 40/60/90/120/150sec. ≤3sec. On-off - 2xEPU(=2aux.switches@5°and85°) MRedMax - 30 - BF3 30Nm 40/60/90/120/150sec. ≤3sec. On-off - Ex-iFireSafeconnector+2xEPU(s.o.) MRedMax - 50 - BF3 50Nm 40/60/90/120/150sec. ≤3sec. On-off - Ex-iFireSafeconnector+2xEPU(s.o.) M


Ex-n quarter turn actuators with 3 sec. spring return for Offshore application, 24 to 230 VAC/DC

Explosion proof Features of RedMax - ... size „M“

RedMax-...-CTM Size „M“, aluminium housing Amercoat painted, resistant against corrosive and/or maritime atmosphere, some parts nickel plated RedSwitch 2 external, adaptable, on site adjustable Ex-aux. switches with 2 potentail free contacts, adaptable to RedMax-... actuators RedBox-3P Ex-e terminal box connectable to RedMax-... actuators with 1 cable for On-off or 3-pos operation RedBox-3P/SW Ex-e terminal box connectable to RedMax-... actuators with 1 cable for On-off or 3-pos operation + 2 cable for external aux. switches type RedSwitch RedBox-Y/S Ex-e terminal box connectable to RedMax-... actuators with 2 cable, for modulating operation or 3-pos + integr. switches (HS) RedBox-Y/S/SW Ex-e terminal box connectable to RedMax-... actuators with 2 cable, for modulating or 3-pos operation with feedback signal + 2 cable for external aux. switches RedBox-BF Ex-e terminal box connectable to RedMax-... actuators with 1 cable, for all ExMax-...-BF RedBox-…/CT Ex-e terminal-box, housing AMERCOAT painted, resistant against corrosive and/or maritime atmosphere, some parts nickel plated, surcharge on aluminium version MKK-M Mounting bracket for …Box-terminal boxes for direct coupling to …Max... actuators size „M“ HV-MK, HV-ML Manual override, connectable to …Max-…actuators size „M“. HV-MK=short version, HV-ML=long version for add. mounting of ...Box/Switch AR-16-xx Squared reduction part from 16x16 mm to shafts with 14 mm (type AR-16-14), 12 mm (type AR-16-12) D-F-…M Adaptation with flange acc. to DIN EN 5211 for butterfly or ball-valves suitable for size „M“ FireSafe Safety temperature trigger for fire dampers, switching at 72°C, with electrical connector, only connectable to …Max-…-BF actuators !

Type Technical data


EUR/unit 799,– 999,– 849,– 1.049,– 999,– 1.199,–

EUR/unit 1.099,– 1.299,– 1.149,– 1.349,– 1.299,– 1.499,– on requ. on requ.


EUR/unit 299,– 159,– 59,– 69,– 79,– 89,– 89,– 89,– 20,– 89,– 18,–on requ. 99,–

www.schischek.com

Price list 2008


InMax 90° quarter turn actuators „S“ for safe area

InMax- ...InMax actuators are NOT Explosion proof

and only for use in safe area

IP66

Basics for all InMax-.. size „S“24…230 VAC/DC self adaptable power supplyUp to 5 different running times adjustable on site95°angle of rotation (5° for pretention), 100% overload protected, aluminium housing IP 66, cable ~ 1 m-40...+40°C/+50°C, integrated heater, Simple manual overrideSquared shaft connection 12 × 12 mmDimensions (L × W × D) 210 × 95 × 80 mm

DescriptionInMax are, in acc. with type, for automation of air dampers, fire and smoke dampers, volume control, as well as for ball valves, throttle valves and other quarter turn armatures.


Size „S“

InMax - 5.10 5 Nm / 10 Nm 3/15/30/60/120 sec. - On-off, 3-pos - - S InMax - 15.30 15 Nm / 30 Nm 3/15/30/60/120 sec. - On-off, 3-pos - - S InMax - 5.10 - S 5 Nm / 10 Nm 3/15/30/60/120 sec. - On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) S InMax - 15.30 - S 15 Nm / 30 Nm 3/15/30/60/120 sec. - On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) S InMax - 5.10 - Y 5 Nm / 10 Nm 7,5/15/30/60/120 sec. - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S InMax - 15.30 - Y 15 Nm / 30 Nm 7,5/15/30/60/120 sec. - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S


Quarter turn actuators without spring return, 24 to 230 VAC/DC

InMax - 5.10 - F 5 Nm / 10 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - - S InMax - 15 - F 15 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - - S InMax - 5.10 - SF 5 Nm / 10 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) S InMax - 15 - SF 15 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) S InMax - 5.10 - YF 5 Nm / 10 Nm 7,5/15/30/60/120 sec. ~ 3 sec. / 10 sec. 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S InMax - 15 - YF 15 Nm 7,5/15/30/60/120 sec. ~ 3 sec. / 10 sec. 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S InMax - 5.10 - BF 5 Nm / 10 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - NormSafe connector + 2 x EPU (s.o.) SInMax - 15 - BF 15 Nm 3/15/30/60/120 sec. ~ 3 sec. / 10 sec. On-off, 3-pos - NormSafe connector + 2 x EPU (s.o.) S


Quarter turn actuators with spring return, 24 to 230 VAC/DC

InMax - 15 - F3 15Nm 3/15/30/60/120sec. ≤3sec. On-off - - SInMax - 15 - SF3 15Nm 3/15/30/60/120sec. ≤3sec. On-off - 2xEPU(=2aux.switches@5°and85°) SInMax - 15 - BF3 15Nm 3/15/30/60/120sec. ≤3sec. On-off - NormSafeconnector+2xEPU(s.o.) S


Quarter turn actuators with 3 sec. spring return for Offshore application, 24 to 230 VAC/DC

Industrial Features of InMax - ... size „S“

InMax-...-VAS Size „S“, housing material in stainless steel AISI 316, some parts nickel plated InMax-...-CTS Size „S“, aluminium housing Amercoat painted, resistant against corrosive and/or maritime atmosphere, some parts nickel plated InSwitch 2 external, adaptable, on site adjustable aux. switches with 2 potentail free contacts, adaptable to InMax-... actuators InBox-3P Terminal box connectable to InMax-... actuators with 1 cable for On-off or 3-pos operation InBox-3P/SW Terminal box connectable to InMax-... actuators with 1 cable for On-off or 3-pos operation + 2 cable for external aux. switches type InSwitch InBox-Y/S Terminal box connectable to InMax-... actuators with 2 cable, for modulating operation or 3-pos + integr. switches (HS) InBox-Y/S/SW Terminal box connectable to InMax-... actuators with 2 cable, for modulating or 3-pos operation with feedback signal + 2 cable for external aux. switches InBox-BF Terminal box connectable to InMax-... actuators with 1 cable, for all InMax-...-BF InBox-…/VA Terminal-box, housing made of stainless-steel type AISI 316 L, some parts nickel plated, surcharge on aluminium version InBox-…/CT Terminal-box, housing AMERCOAT painted, resistant against corrosive and/or maritime atmosphere, some parts nickel plated, surcharge on aluminium version MKK-S Mounting bracket for …Box-terminal boxes for direct coupling to …Max... actuators size „S“ MKK-S/VA Mounting bracket, made of stainless-steel suitable for InBox...VA KB-S Mounting clamp for round damper shaft Ø 10 to 20 mm and squared shafts 10 to 16 mm, incl. bracket, connectable to all InMax-... size „S“ HV-SK, HV-SL Manual override, connectable to …Max-... actuators size „S“. HV-SK=short version, HV-SL=long version for add. mounting of ...Box/Switch AR-12-xx Squared reduction part from 12x12 mm to shafts with 11mm (type AR-12-11), 10 mm (type AR-12-10), 8 mm (type AR-12-08) D-F-…S Adaptation with flange acc. to DIN EN 5211 for butterfly or ball-valves suitable for size „S“ NormSafe Safety temperature trigger for fire dampers, switching at 72°C, with electrical connector, only connectable to InMax-…-BF actuators !

Type Technical data


EUR/unit 399,– 499,– 449,– 549,– 499,– 599,–

EUR/unit 529,– 629,– 579,– 679,– 629,– 729,–on requ.on requ.

EUR/unit 749,– 799,–on requ.

EUR/unit 499,– 199,– 139,– 49,– 59,– 69,– 79,– 79,– 179,– 79,– 14,– 24,– 49,– 69,– 9,– on requ. 89,–

www.schischek.com

Price list 2008


InMax 90° quarter turn actuators „M“ for safe area

InMax- ...InMax actuators are NOT Explosion proof


IP66

Basics for all InMax-.. size „M“24…230 VAC/DC self adaptable power supplyUp to 5 different running times adjustable on site95°angle of rotation (5° for pretention), 100% overload protected, aluminium housing IP 66, cable ~ 1 m-40...+40°C/+50°C, integrated heater, Simple manual overrideSquared shaft connection 16 × 16 mmDimensions (L × W × D) 287 × 149 × 116 mm

DescriptionInMax are, in acc. with type, for automation of air dampers, fire and smoke dampers, volume control, as well as for ball valves, throttle valves and other quarter turn armatures.


Size „M“

InMax - 50.75 50 Nm / 75 Nm 40/60/90/120/150 sec. - On-off, 3-pos - - M InMax - 100 100 Nm 40/60/90/120/150 sec. - On-off, 3-pos - - M InMax - 50.75 - S 50 Nm / 75 Nm 40/60/90/120/150 sec. - On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) M InMax - 100 - S 100 Nm 40/60/90/120/150 sec. - On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) M InMax - 50.75 - Y 50 Nm / 75 Nm 40/60/90/120/150 sec. - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - M InMax - 100 - Y 100 Nm 40/60/90/120/150 sec. - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - M


Quarter turn actuators without spring return, 24 to 230 VAC/DC

InMax - 30 - F 30 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - - M InMax - 50 - F 50 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - - M InMax - 30 - SF 30 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) M InMax - 50 - SF 50 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - 2 x EPU ( = 2 aux. switches @ 5° and 85°) M InMax - 30 - YF 30 Nm 40/60/90/120/150 sec. ~20 sec. 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - M InMax - 50 - YF 50 Nm 40/60/90/120/150 sec. ~20 sec. 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - M InMax - 30 - BF 30 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - NormSafe connector + 2 x EPU (s.o.) MInMax - 50 - BF 50 Nm 40/60/90/120/150 sec. ~20 sec. On-off, 3-pos - NormSafe connector + 2 x EPU (s.o.) M


Quarter turn actuators with spring return, 24 to 230 VAC/DC

InMax - 30 - F3 30Nm 40/60/90/120/150sec. ≤3sec. On-off - - MInMax - 50 - F3 50Nm 40/60/90/120/150sec. ≤3sec. On-off - - MInMax - 30 - SF3 30Nm 40/60/90/120/150sec. ≤3sec. On-off - 2xEPU(=2aux.switches@5°and85°) MInMax - 50 - SF3 50Nm 40/60/90/120/150sec. ≤3sec. On-off - 2xEPU(=2aux.switches@5°and85°) MInMax - 30 - BF3 30Nm 40/60/90/120/150sec. ≤3sec. On-off - NormSafeconnector+2xEPU(s.o.) MInMax - 50 - BF3 50Nm 40/60/90/120/150sec. ≤3sec. On-off - NormSafeconnector+2xEPU(s.o.) M


Quarter turn actuators with 3 sec. spring return for Offshore application, 24 to 230 VAC/DC

Industrial Features of InMax - ... size „M“

InMax-...-CTM Size „M“, aluminium housing Amercoat painted, resistant against corrosive and/or maritime atmosphere, some parts nickel plated InSwitch 2 external, adaptable, on site adjustable aux. switches with 2 potentail free contacts, adaptable to InMax-... actuators InBox-3P Terminal box connectable to InMax-... actuators with 1 cable for On-off or 3-pos operation InBox-3P/SW Terminal box connectable to InMax-... actuators with 1 cable for On-off or 3-pos operation + 2 cable for external aux. switches type InSwitch InBox-Y/S Terminal box connectable to InMax-... actuators with 2 cable, for modulating operation or 3-pos + integr. switches (HS) InBox-Y/S/SW Terminal box connectable to InMax-... actuators with 2 cable, for modulating or 3-pos operation with feedback signal + 2 cable for external aux. switches InBox-BF Terminal box connectable to InMax-... actuators with 1 cable, for all ExMax-...-BF InBox-…/CT Terminal-box, housing AMERCOAT painted, resistant against corrosive and/or maritime atmosphere, some parts nickel plated, surcharge on aluminium version MKK-M Mounting bracket for …Box-terminal boxes for direct coupling to …Max... actuators size „M“ HV-MK, HV-ML Manual override, connectable to …Max-…actuators size „M“. HV-MK=short version, HV-ML=long version for add. mounting of ...box/switch AR-16-xx Squared reduction part from 16x16 mm to shafts with 14 mm (type AR-16-14), 12 mm (type AR-16-12) D-F-…M Adaptation with flange acc. to DIN EN 5211 for butterfly or ball-valves suitable for size „M“ NormSafe Safety temperature trigger for fire dampers, switching at 72°C, with electrical connector, only connectable to InMax-…-BF actuators !

Type Technical data


EUR/unit 699,– 899,– 749,– 949,– 899,– 1.099,–

EUR/unit 999,– 1.199,– 1.049,– 1.249,– 1.199,– 1.399,– on requ. on requ.


EUR/unit 299,– 139,– 49,– 59,– 69,– 79,– 79,– 79,– 20,– 89,– 18,–on requ. 89,–

Price list 2008

www.schischek.com

10


Ex-d valve actuator without spring return, 24 to 230 VAC/DC

Explosion proof Features of ExRun, RedRun, InRunRedRun...

Explosion proofzone 2, 22gas + dust

PTB-certifiedII3G..II3D..

ATEX 94/9/EC

ExRun...Explosion proof

zone 1, 2, 21, 22gas + dust


ATEX 94/9/EC

InRun...InRun actuators are NOT Explosion proof


IP66

IndustrialBasics for all …Run valve actuators

24…230 VAC/DC self adaptable power supplyUp to 5 different running times adjustable on site5 to 60 mm stroke, mechanical limitation on each positionAutomatic adaptation of modulating signal at Ex-, Red-, InRun-…-Y..Aluminium housing IP 66, integrated terminal box-40…+40°C/+50°C, integrated heater, Simple manual overrideDimension (L*×W×D) 260 × 208 × 115 mm (dimension without adaptation)*Length = variable, depending on type

DescriptionExRun, RedRun and InRun valve actuators are used for automation of 2- and 3-way valves with 3-pos. on-off or modulating mode.

Delivery: 1 actuator with integrated Ex-e terminal box, simple manual override.

Necessary accessories: valve adaptation in acc. with valve manufacturer, type and nominal size (diameter).

ExRun/RedRun/InRun Valve actuators size „S“

Ex-n valve actuator without spring return, 24 to 230 VAC/DC

ExRun - 5.10 - X 500 / 1.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - ExSwitch not adaptable! S ExRun - 25.50 - X 2.500 / 5.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - ExSwitch not adaptable! S ExRun - 75.100 - X 7.500 / 10.000 N (8.000 N) 4/6/9/12/15 sec/mm - On-off, 3-pos - ExSwitch not adaptable! S ExRun - 5.10 500 / 1.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - - S ExRun - 25.50 2.500 / 5.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - - S ExRun - 75.100 7.500 / 10.000 N (8.000 N) 4/6/9/12/15 sec/mm - On-off, 3-pos - - S ExRun - 5.10 - S 500 / 1.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - 2 aux. switch, fixed switching points S ExRun - 25.50 - S 2.500 / 5.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - 2 aux. switch, fixed switching points S ExRun - 75.100 - S 7.500 / 10.000 N (8.000 N) 4/6/9/12/15 sec/mm - On-off, 3-pos - 2 aux. switch, fixed switching points S ExRun - 5.10 - P 500/1.000N 2/3/6/9/12sec/mm - On-off,3-pos-P feedbackpotentiometer1.000Ω - SExRun - 25.50 - P 2.500/5.000N 2/3/6/9/12sec/mm - On-off,3-pos-P feedbackpotentiometer1.000Ω - SExRun - 75.100 - P 7.500/10.000N(8.000N) 4/6/9/12/15sec/mm - On-off,3-pos-P feedbackpotentiometer1.000Ω - SExRun - 5.10 - Y 500 / 1.000 N 2/3/6/9/12 sec/mm - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S ExRun - 25.50 - Y 2.500 / 5.000 N 2/3/6/9/12 sec/mm - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S ExRun - 75.100 - Y 7.500 / 10.000 N (8.000 N) 4/6/9/12/15 sec/mm - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S

RedRun - 5.10 - X 500 / 1.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - RedSwitch not adaptable! S RedRun - 25.50 - X 2.500 / 5.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - RedSwitch not adaptable! S RedRun -75.100 - X 7.500 / 10.000 N (8.000 N) 4/6/9/12/15 sec/mm - On-off, 3-pos - RedSwitch not adaptable! S RedRun - 5.10 500 / 1.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - - S RedRun - 25.50 2.500 / 5.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - - S RedRun -75.100 7.500 / 10.000 N (8.000 N) 4/6/9/12/15 sec/mm - On-off, 3-pos - - S RedRun - 5.10 - S 500 / 1.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - 2 aux. switch, fixed switching points S RedRun - 25.50 - S 2.500 / 5.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - 2 aux. switch, fixed switching points S RedRun -75.100 - S 7.500 / 10.000 N (8.000 N) 4/6/9/12/15 sec/mm - On-off, 3-pos - 2 aux. switch, fixed switching points S RedRun - 5.10 - P 500/1.000N 2/3/6/9/12sec/mm - On-off,3-pos-P feedbackpotentiometer1.000Ω - SRedRun - 25.50 - P 2.500/5.000N 2/3/6/9/12sec/mm - On-off,3-pos-P feedbackpotentiometer1.000Ω - SRedRun -75.100 - P 7.500/10.000N(8.000N) 4/6/9/12/15sec/mm - On-off,3-pos-P feedbackpotentiometer1.000Ω - SRedRun - 5.10 - Y 500 / 1.000 N 2/3/6/9/12 sec/mm - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S RedRun - 25.50 - Y 2.500 / 5.000 N 2/3/6/9/12 sec/mm - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S RedRun -75.100 - Y 7.500 / 10.000 N (8.000 N) 4/6/9/12/15 sec/mm - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S

Type Force Running time Spring return Control mode Feedback Features Size

Type Force Running time Spring return Control mode Feedback Features Size

from IV. quarter 2008

EUR/unit 999,– 1.199,– 1.499,– 1.099,– 1.299,– 1.599,– 1.199,– 1.399,– 1.699,– 1.199,– 1.399,– 1.699,– 1.399,– 1.599,– 1.899,–

EUR/unit 899,– 1.099,– 1.399,– 999,– 1.199,– 1.499,– 1.099,– 1.299,– 1.599,– 1.099,– 1.299,– 1.599,– 1.299,– 1.499,– 1.799,–

Price list 2008

www.schischek.com 11


Valve actuator without spring return, 24 to 230 VAC/DC

To select the right valve adaptation and get the right price information the following data are required:

1. Valve manufacturer2. Valve type3. Valve nominal size (diameter) DNFor adaptations which are still designed by Schischek this data are minimum requirements.

To design new adaptations we need additional details of the valve body as well as drawings.At purchase order you have to order both parts actuator + adaptation.

Adaptation

…Run + valve adaptationRequired data for valve adaptation

Accessories (additional cost)Type Technical data …Run-…-CTS Size „S“, aluminium housing with Amercoat painting, resistant against corrosive and/or maritime atmosphere, some parts nickel plated ExSwitch 2 external, adaptable, on site adjustable Ex-aux. switches with 2 potentail free contacts, additionally Ex-e terminal box + mounting bracket necessary RedSwitch 2 external, adaptable, on site adjustable Ex-aux. switches with 2 potentail free contacts, additionally Ex-e terminal box + mounting bracket necessary InSwitch 2 external, adaptable, on site adjustable switches with 2 potentail free contacts, additionally terminal box + mounting bracket necessary ExBox-SW Ex-e terminal box suitable for ExRun...valve-actuators with external switches ExSwitch RedBox-SW Ex-e terminal box suitable for RedRun...valve-actuators with external switches RedSwitch InBox-SW Terminal box suitable for InRun...valve-actuators with external switches InSwitch MKK-S Mounting-bracket suitable for ...Box-terminal boxes for direct mounting on ...Run actuators size „S“ HV-SK, HV-SL Manual override with locking mechanism suitable for ...Run actuators size „S“. HV-SK = short version, HV-SL = long version for add. mounting of ...Box/Switch Adaptation Different adaptations for different valve types and sizes available. Please don‘t hesitate to ask for technical solution

ExRun-…RedRun-…InRun-…

InRun - 5.10 - X 500 / 1.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - InSwitch not adaptable! S InRun - 25.50 - X 2.500 / 5.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - InSwitch not adaptable! S InRun -75.100 - X 7.500 / 10.000 N (8.000 N) 4/6/9/12/15 sec/mm - On-off, 3-pos - InSwitch not adaptable! S InRun - 5.10 500 / 1.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - - S InRun - 25.50 2.500 / 5.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - - S InRun -75.100 7.500 / 10.000 N (8.000 N) 4/6/9/12/15 sec/mm - On-off, 3-pos - - S InRun - 5.10 - S 500 / 1.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - 2 aux. switch, fixed switching points S InRun - 25.50 - S 2.500 / 5.000 N 2/3/6/9/12 sec/mm - On-off, 3-pos - 2 aux. switch, fixed switching points S InRun -75.100 - S 7.500 / 10.000 N (8.000 N) 4/6/9/12/15 sec/mm - On-off, 3-pos - 2 aux. switch, fixed switching points S InRun - 5.10 - P 500/1.000N 2/3/6/9/12sec/mm - On-off,3-pos-P feedbackpotentiometer1.000Ω - SInRun - 25.50 - P 2.500/5.000N 2/3/6/9/12sec/mm - On-off,3-pos-P feedbackpotentiometer1.000Ω - SInRun -75.100 - P 7.500/10.000N(8.000N) 4/6/9/12/15sec/mm - On-off,3-pos-P feedbackpotentiometer1.000Ω - SInRun - 5.10 - Y 500 / 1.000 N 2/3/6/9/12 sec/mm - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S InRun - 25.50 - Y 2.500 / 5.000 N 2/3/6/9/12 sec/mm - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S InRun -75.100 - Y 7.500 / 10.000 N (8.000 N) 4/6/9/12/15 sec/mm - 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA - S

Type Force Running time Spring return Control mode Feedback Features Size EUR/unit 799,– 999,– 1.299,– 899,– 1.099,– 1.399,– 999,– 1.199,– 1.499,– 999,– 1.199,– 1.499,– 1.199,– 1.399,– 1.699,–

EUR/unit 299,– 199,– 159,– 139,– 79,– 69,– 59,– 14,– 69,–on requ.

Price list 2008

www.schischek.com

1


Explosion proof Features of ExPlus, RedPlus, InPlusExPlus/RedPlus/InPlus Linear actuators up to 300 mm stroke

ExPlus ...Explosion proof



ATEX 94/9/EC

Basics for all …Plus actuators24…230 V AC/DC self adaptable power supplyUp to 5 different running times adjustable on site, 100 % overload protectedAluminium housing IP66Integrated heater, -40...+40°C/+50°C1 m cable, Mounting bracket, 2 fork-linksIn acc. with type:300 or 3.000 N force100 and 300 mm strokeOn-off, 3-pos, 0-10VDC, 4-20mAExPlus for installation in zone 1, 2, 21, 22RedPlus for installation in zone 2, 22InPlus for installation in the safe area

DescriptionExPlus, RedPlus and InPlus actuators for linear motion or rotary operation via lever. Types Ex-Red-In are different in certi-fication, but with same functions and dimension.

Delivery: 1 actuator with 1 m cable, 2 linkages and 1 mounting bracket

IndustrialRedPlus ...



ATEX 94/9/EC

Type Force Stroke Running time Control mode Feedback Features

ExPlus... Ex-d linear actuator, 24...230 VAC/DC, zone 1, 2, 21, 22

ExPlus- 3.5-100 - X 300 N / 500 N 100 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - ExSwitch not adaptable! ExPlus- 3.5-300 - X 300 N / 500 N 300 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - ExSwitch not adaptable! ExPlus-10.30-100 - X 1.000 N / 3.000 N 100 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - ExSwitch not adaptable! ExPlus-10.30-300 - X 1.000 N / 3.000 N 300 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - ExSwitch not adaptable! ExPlus- 3.5-100 300 N / 500 N 100 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - ExPlus- 3.5-300 300 N / 500 N 300 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - ExPlus-10.30-100 1.000 N / 3.000 N 100 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - ExPlus-10.30-300 1.000 N / 3.000 N 300 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - ExPlus- 3.5-100 - Y 300 N / 500 N 100 mm 0,5 / 1,0 / 2,0 sec/mm 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA ExPlus- 3.5-300 - Y 300 N / 500 N 300 mm 0,5 / 1,0 / 2,0 sec/mm 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA ExPlus-10.30-100 - Y 1.000 N / 3.000 N 100 mm 0,5 / 1,0 / 2,0 sec/mm 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA ExPlus-10.30-300 - Y 1.000 N / 3.000 N 300 mm 0,5 / 1,0 / 2,0 sec/mm 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA


RedPlus... Ex-n linear actuator, 24...230 VAC/DC, zone 2, 22

RedPlus- 3.5-100 - X 300 N / 500 N 100 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - RedSwitch not adaptable! RedPlus- 3.5-300 - X 300 N / 500 N 300 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - RedSwitch not adaptable! RedPlus-10.30-100 - X 1.000 N / 3.000 N 100 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - RedSwitch not adaptable! RedPlus-10.30-300 - X 1.000 N / 3.000 N 300 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - RedSwitch not adaptable! RedPlus- 3.5-100 300 N / 500 N 100 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - RedPlus- 3.5-300 300 N / 500 N 300 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - RedPlus-10.30-100 1.000 N / 3.000 N 100 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - RedPlus-10.30-300 1.000 N / 3.000 N 300 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - RedPlus- 3.5-100 - Y 300 N / 500 N 100 mm 0,5 / 1,0 / 2,0 sec/mm 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA RedPlus- 3.5-300 - Y 300 N / 500 N 300 mm 0,5 / 1,0 / 2,0 sec/mm 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA RedPlus-10.30-100 - Y 1.000 N / 3.000 N 100 mm 0,5 / 1,0 / 2,0 sec/mm 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA RedPlus-10.30-300 - Y 1.000 N / 3.000 N 300 mm 0,5 / 1,0 / 2,0 sec/mm 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA


InPlus... linear actuator, 24...230 VAC/DC, safe area (Industrial application, NON Ex)

InPlus- 3.5-100 - X 300 N / 500 N 100 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - InSwitch not adaptable! InPlus- 3.5-300 - X 300 N / 500 N 300 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - InSwitch not adaptable! InPlus-10.30-100 - X 1.000 N / 3.000 N 100 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - InSwitch not adaptable! InPlus-10.30-300 - X 1.000 N / 3.000 N 300 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - InSwitch not adaptable! InPlus- 3.5-100 300 N / 500 N 100 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - InPlus- 3.5-300 300 N / 500 N 300 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - InPlus-10.30-100 1.000 N / 3.000 N 100 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - InPlus-10.30-300 1.000 N / 3.000 N 300 mm 0,5 / 1,0 / 2,0 sec/mm On-off, 3-pos - InPlus- 3.5-100 - Y 300 N / 500 N 100 mm 0,5 / 1,0 / 2,0 sec/mm 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA InPlus- 3.5-300 - Y 300 N / 500 N 300 mm 0,5 / 1,0 / 2,0 sec/mm 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA InPlus-10.30-100 - Y 1.000 N / 3.000 N 100 mm 0,5 / 1,0 / 2,0 sec/mm 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA InPlus-10.30-300 - Y 1.000 N / 3.000 N 300 mm 0,5 / 1,0 / 2,0 sec/mm 3-pos, 0...10VDC, 4...20 mA 0...10VDC, 4...20 mA

InPlus...InPlus actuators are NOT Explosion proof


IP66

from IV. quarter 2008

EUR/unit 799,– 899,– 999,– 1.099,– 899,– 999,– 1.099,– 1.199,– 999,– 1.099,– 1.199,– 1.299,–

EUR/unit 699,– 799,– 899,– 999,– 799,– 899,– 999,– 1.099,– 899,– 999,– 1.099,– 1.199,–

EUR/unit 599,– 699,– 799,– 899,– 699,– 799,– 899,– 999,– 799,– 899,– 999,– 1.099,–

Price list 2008

www.schischek.com 1

100 mm 200 mm 300 mm 300 N 15 Nm 30 Nm 45 Nm 500 N 25 Nm 50 Nm 75 Nm 1000 N 50 Nm 100 Nm 150 Nm 3000 N 150 Nm 300 Nm 450 Nm

90°

90°


…Plus-…-CTS Size „S“, aluminium housing with Amercoat painting, resistant against corrosive and/or maritime atmosphere, some parts nickel plated ExSwitch 2 external, adaptable, on site adjustable Ex-aux. switches with 2 potentail free contacts, adaptable to ExPlus-... actuators RedSwitch 2 external, adaptable, on site adjustable Ex-aux. switches with 2 potentail free contacts, adaptable to RedPlus-... actuators InSwitch 2 external, adaptable, on site adjustable aux. switches with 2 potentail free contacts, adaptable to InPlus-... actuators ExBox-SW Ex-e terminal box suitable for ExPlus...linear-actuators with external switches ExSwitch RedBox-SW Ex-e terminal box suitable for RedPlus...linear-actuators with external switches RedSwitch InBox-SW Terminal box suitable for InPlus...linear-actuators with external switches InSwitch MKK-S Mounting-bracket suitable for ...Box-terminal boxes for direct mounting on ...Plus linear actuators HV-SK, HV-SL Manual override with locking mechanism suitable for ...Plus linear actuators. HV-SK=short version, HV-SL=long version for add. mounting of ...Box/Switch

Type Technical data

Accessories ExPlus, RedPlus, InPlus (additional price)

300 mm Stroke100 mm StrokeMounting variations

ForceTorque at stroke

EUR/unit 299,– 199,– 159,– 129,– 79,– 69,– 59,– 14,– 69,–

Price list 2008

www.schischek.com

1

ΔPExCon-PΔ P

°C%rF

°C%rF

°C%rF

°C%rFΔ P

ExCon-D+ ExPro

ExCon-A+ ExSens

EXL-IMU-1+ ExSens

EXL-IRU-1+ ExSens

normal wiring

normal wiring

Duct sensor

Room sensor

| Type | Description

Ex-i wiring (intrinsically safe)

normal wiring


normal wiring


normal wiring

The new sensors are subdevided in 3 installation- and 3 application-areas.

Installation-areas: ExCon-… Sensor for Ex-area zone 1, 2, 21, 22 RedCon-… Sensor for Ex-area zone 2, 22 InCon-… Sensor for safe area

Application-areas:Ex/Red/ InCon-P sensors for pressure and differential pressure Ex/Red/ InCon-D + …Pro active sensor-heads for temperature and /or humidity Ex/Red/ InCon-A + …Sens passive sensors for temperature, humidity and potentiometer

The new sensor concept grant enormous advantages to known solutions, especially in hazardous zones:

1. No transducer in the electrical control-panel necessary2. No intrinsic safe electrical circuit within the control-panel necessary3. No intrinsic safe electrical circuit between the electrical control-panel and the sensor necessary4. Cost reduction within the electrical components5. Cost reduction within installation

| Installation examples

ExCon-P…, RedCon-P…, InCon-P… Sensors Transducers with integrated differential-pressure sensor for direct connection of the air-hoses. IP 66 aluminium housing with integrated terminal-box. Measuring range parametrizable on site. Outputs 0…10V VDC/4…20 mA. Integrated actual value indication, illuminated.

ExCon-D…, RedCon-D…, InCon-D… Transducer + ExPro, InPro-sensor probeTransducer for the installation of an ExPro, or InPro (with InCon-D) for temperature C° and/or humidity in %. IP 66 aluminium housing with integrated terminal-box. Measuring-range parametrizable on site. Outputs 0…10V VDC/4…20 mA. Integrated actual value indication, illuminated.

ExCon-A…, RedCon-A…, InCon-A… Transducer + ExSens sensor Transducer for a connection of an passive, modula-tingExSenssensortypePt100,Ni1000,0…10kΩover Ex-i electrical conduit. IP66 aluminium housing with integrated terminal-box. Measuring range pa-rametrizable on site. Outputs 0…10V VDC/4…20 mA. Integrated actual value indication, illuminated.

EXL-IMU-1 transducer + ExSens sensor Transducer for a connection of an passive, modu-lating ExSens sensor type Pt 100, Ni 1000, 0…10 kΩoverEx-ielectricalconduit.Installationincontrolbox onto DIN-rail. Measuring range parametrizable at site. Outputs 0…10V VDC/4…20 mA. Integrated actual value indication.

EXL-IRU-1 transducer + ExSens sensor Switching module for a connection of an passive, binary ExSens sensor, e.g. diff. pressure switch, frost protection thermostat or hygrostat through intrinsically safe electrical conduit. Installation in control box onto DIN-rail. Output is potential-free.

Pressure, Differential Pressure, VAV – modulating, active

Temperature and /or Humidity – modulating, active

Temperature and /or Humidity, Potentiometer – modulating, passive

Temperature, Humidity, Potentiometer – modulating, passive

Temperature, Humidity, Differential Pressure – binary, passive

Safe area Ex area

The new ExCon..., RedCon and InCon Sensor-TechnologyExCon../RedCon../InCon.. Sensors Overview and Accessories

Price list 2008

www.schischek.com 1


ExCon - P100 +/- 100 Pa up to 25.000 Pa +/- Measurement range free adjustable, min. range 20 Pa zone 1, 2, 21, 22 ExCon - P250 +/- 250 Pa up to 25.000 Pa +/- Measurement range free adjustable, min. range 50 Pa zone 1, 2, 21, 22 ExCon - P500 +/- 500 Pa up to 50.000 Pa +/- Measurement range free adjustable, min. range 100 Pa zone 1, 2, 21, 22 ExCon - P1250 +/- 1.250 Pa up to 50.000 Pa +/- Measurement range free adjustable, min. range 250 Pa zone 1, 2, 21, 22 ExCon - P2500 +/- 2.500 Pa up to 50.000 Pa +/- Measurement range free adjustable, min. range 500 Pa zone 1, 2, 21, 22 ExCon - P5000 +/- 5.000 Pa up to 75.000 Pa +/- Measurement range free adjustable, min. range 1.000 Pa zone 1, 2, 21, 22 ExCon - P7500 +/- 7.500 Pa up to 120.000 Pa +/- Measurement range free adjustable, min. range 1.500 Pa zone 1, 2, 21, 22

Type Max. range Overload protected Measurement range, min. 20% of max. range Installation sensor

ExCon-P... Differential pressure and volume control sensors zone 1, 2, 21, 22

RedCon - P100 +/- 100 Pa up to 25.000 Pa +/- Measurement range free adjustable, min. range 20 Pa zone 2, 22 RedCon - P250 +/- 250 Pa up to 25.000 Pa +/- Measurement range free adjustable, min. range 50 Pa zone 2, 22 RedCon - P500 +/- 500 Pa up to 50.000 Pa +/- Measurement range free adjustable, min. range 100 Pa zone 2, 22 RedCon - P1250 +/- 1.250 Pa up to 50.000 Pa +/- Measurement range free adjustable, min. range 250 Pa zone 2, 22 RedCon - P2500 +/- 2.500 Pa up to 50.000 Pa +/- Measurement range free adjustable, min. range 500 Pa zone 2, 22 RedCon - P5000 +/- 5.000 Pa up to 75.000 Pa +/- Measurement range free adjustable, min. range 1.000 Pa zone 2, 22 RedCon - P7500 +/- 7.500 Pa up to 120.000 Pa +/- Measurement range free adjustable, min. range 1.500 Pa zone 2, 22


RedCon-P... Differential pressure and volume control sensors zone 2, 22

Ex/RedCon-P… -A Module as before, but with 1 intrisically safe circuit 4…20 mA output to connect external actual value indicator InCon-P… -A Module as before, but with one 4…20 mA output to connect external actual value indicator EXC-RIA-261 Intrinsic safe actual value LCD indicator, for use in zone 1, 2, 21, 22, connectable to Ex-, RedCon… sensors with type addition …P.. - A NOC-RIA-261 LCD indicator, connectable to InCon… sensors with type addition …P.. - A MKR Mounting bracket for installation on round air-ducts (diameter up to 600 mm) Installation kit 2 Includes 2 meter pressure hose (inner diameter 6 mm) 2 plastic fittings

Type Technical data


ExCon-P/RedCon-P/InCon-P Differential pressure sensorsExplosion proof Industrial Features of ExCon-P, RedCon-P, InCon-P sensors

ExCon - P...Explosion proof


PTB-certifiedII2(1)G Ex ema [ia] IIC T6

II2(1)D Ex tD A21 [iaD] IP66 T80°C ATEX 94/9/EC

RedCon - P...Explosion proof

zone 2, 22gas + dust

PTB-certifiedII3(1)G Ex nC [ia] IIC T6


DescriptionExCon-P, RedCon-P and InCon-P are pressure sensors for HVAC systems, e.g. for differential pressure- or VAV control. VAV control must be tested by the ma-nufacturerer of VAV dampers in acc. with diameter, design and characteristics of the air damper.

Delivery: 1 sensor with integrated terminal box

Basics for all …Con-P sensorsNo additional module in the panel required !No intrinsically safe wiring required24 VAC/DC supply0…10 VDC, 4…20 mA selectable on siteMeasurement range adjustable.Actual value indication (which can be switched off)All parameters can be adjusted on site without additional tools and measurement devicesAluminium housing IP 66Integrated terminal boxDimensions (L × W × D) 177 × 107 × 66 mm

InCon - P100 +/- 100 Pa up to 25.000 Pa +/- Measurement range free adjustable, min. range 20 Pa safe area InCon - P250 +/- 250 Pa up to 25.000 Pa +/- Measurement range free adjustable, min. range 50 Pa safe area InCon - P500 +/- 500 Pa up to 50.000 Pa +/- Measurement range free adjustable, min. range 100 Pa safe area InCon - P1250 +/- 1.250 Pa up to 50.000 Pa +/- Measurement range free adjustable, min. range 250 Pa safe area InCon - P2500 +/- 2.500 Pa up to 50.000 Pa +/- Measurement range free adjustable, min. range 500 Pa safe area InCon - P5000 +/- 5.000 Pa up to 75.000 Pa +/- Measurement range free adjustable, min. range 1.000 Pa safe area InCon - P7500 +/- 7.500 Pa up to 120.000 Pa +/- Measurement range free adjustable, min. range 1.500 Pa safe area


InCon-P... Differential pressure and volume control sensors for safe areas

InCon - P...InCon sensors are

NOT Explosion proof and only for use

in safe areaIP66

EUR/unit 899,– 899,– 899,– 899,– 899,– 899,– 899,–

EUR/unit 799,– 799,– 799,– 799,– 799,– 799,– 799,–

EUR/unit 599,– 599,– 599,– 599,– 599,– 599,– 599,–

EUR/unit 99,– 89,– 499,– 479,– 39,– 15,–

Price list 2008

www.schischek.com

1


RedCon - D…




ExCon-D/RedCon-D/InCon-D Temperature /humidity transducer

ExCon - D…

Explosion proofzone 1, 2, 21, 22

gas + dustPTB-certified

II2(1)G Ex ema [ia] IIC T6II2(1)D Ex tD A21 [iaD] IP66 T80°C

ATEX 94/9/EC

Basics for all …Con-D sensorsNo additional module in the panel required !No intrinsically safe wiring required.24 VAC/DC supplyConnector for ExPro sensors for room or duct mounting0…10 VDC, 4…20 mA selectable on siteMeasurement range adjustable.Actual value indication (which can be switched off).All parameters can be adjusted on site without additional tools and measurement devices.Aluminium housing IP 66Integrated terminal boxDimensions (L × W × D) 177 × 107 × 66 mmExCon-D for zone 1, 2, 21, 22RedCon-D for zone 2, 22InCon-D for safe area

DescriptionExCon-D, RedCon-D and InCon-D trans-ducer together with ExPro / InPro digital sensors are for temperature and/or humidity measurement in HVAC systems.Delivery: 1 transducer with connection for 1 ExPro-… sensorRequired accessory (additional price): 1 ExPro sensorPurchase example for 1 temperature duct sensing, 150 mm sensor tube, additional external value indication, sensor in zone 21, indicator in zone 22.Types to purchase:1 x ExCon-D + type addition …- A (Ex-i transducer)1 x ExPro-CT150 + (Ex-i sensor)1 x EXC-RIA-261 (Ex-i indicator)

ExCon - D Module to connect 1 ExPro sensor for temperture and/or humidity for use in hazardous areas zone 1, 2, 21, 22 zone 1, 2, 21, 22

Type Technical data Installation module Installation ExPro sensor

ExCon-D temperature- /humidity module for zone 1, 2, 21, 22

RedCon - D Module to connect 1 ExPro sensor for temperture and/or humidity for use in hazardous areas zone 2, 22 zone 1, 2, 21, 22

Type Technical data Installation module Installation ExPro sensor

RedCon-D temperature- /humidity module for zone 2, 22

Explosion proof Features ExCon-D, RedCon-D, InCon-D transducer

Ex/RedCon - D-A Module as before, but with 2* intrisic safe circuit 4…20 mA output to connect external actual value indicator InCon - D-A Module as before, but with 2* 4…20 mA outputs to connect external actual value indicators EXC-RIA-261 Intrinsic safe actual value LCD indicator, for use in zone 1, 2, 21, 22, connectable to Ex/RedCon-…D sensors NOC-RIA-261 Actual value LCD indicator, for use in safe area, connectable to InCon-…D sensors MKR Mounting bracket for installation on round air-ducts (diameter up to 600 mm) *Output 1 = for °C, Output 2 = for %rH

Type Technical data


InCon-D temperature- /humidity module for safe areaType Technical data Installation module Installation InPro sensorInCon - D Module to connect 1 InPro sensor for temperture and/or humidity for use in safe area safe area safe area

Industrial

Example of combinations

InCon - D...

InCon sensors are NOT Explosion proof


IP66

EUR/unit 399,–

EUR/unit 379,–

EUR/unit 359,–

EUR/unit 99,– 89,– 499,– 479,– 39,–

Price list 2008

www.schischek.com 1


ExPro/InPro Digital temperature- /humidity sensors

ExPro-…Explosion proof


PTB-certified in acc.with ExCon-D

and RedCon-Dtransducer

ATEX 94/9/EC

Basics for all ExPro sensorsSensors connectable only to ExCon-D…, RedCon-D… transducer. Mechanical and electrical adaptation via connector.ExPro / InPro sensor can be screwed optional on the back or bottom-side of the housing. Using Humidity-sensors, the contamination and aggres-siveness of the medium has to be regarded.

DescriptionExPro sensors for temperature and /or humidity (in acc. with type) in hazardous areas only for use together with ExCon-D… / RedCon-D… transducers !

InPro sensors are suitable for temperature and/or humi-dity measurement in safe area and exceptionalapplicable with InCon-D tranducers.

Delivery: 1 sensor with connectorExample: room-humidity sensor, 50 mm lengthType: 1 x ExPro-CF-50

Attention: only in combination with: 1 × ExCon-D or RedCon-D ( InCon-D by InPro sensors)

Explosion proof Features ExPro, InPro sensors

ExPro-CT - 50 Temperature sensor - 40…+ 125 °C 50 mm Room/duct ExCon-D RedCon-D zone 1, 2, 21, 22 ExPro-CT - 100 Temperature sensor - 40…+ 125 °C 100 mm Duct ExCon-D RedCon-D zone 1, 2, 21, 22 ExPro-CT - 150 Temperature sensor - 40…+ 125 °C 150 mm Duct ExCon-D RedCon-D zone 1, 2, 21, 22 ExPro-CT - 200 Temperature sensor - 40…+ 125 °C 200 mm Duct ExCon-D RedCon-D zone 1, 2, 21, 22 ExPro-CF - 50 Humidity sensor 0…100 %rF 50 mm Room/duct ExCon-D RedCon-D zone 1, 2, 21, 22 ExPro-CF - 100 Humidity sensor 0…100 %rF 100 mm Duct ExCon-D RedCon-D zone 1, 2, 21, 22 ExPro-CF - 150 Humidity sensor 0…100 %rF 150 mm Duct ExCon-D RedCon-D zone 1, 2, 21, 22 ExPro-CF - 200 Humidity sensor 0…100 %rF 200 mm Duct ExCon-D RedCon-D zone 1, 2, 21, 22 ExPro-CTF - 50 Combination temperature /humidity - 40…+ 125 °C, 0…100 %rF 50 mm Room/duct ExCon-D RedCon-D zone 1, 2, 21, 22 ExPro-CTF - 100 Combination temperature /humidity - 40…+ 125 °C, 0…100 %rF 100 mm Duct ExCon-D RedCon-D zone 1, 2, 21, 22 ExPro-CTF - 150 Combination temperature /humidity - 40…+ 125 °C, 0…100 %rF 150 mm Duct ExCon-D RedCon-D zone 1, 2, 21, 22 ExPro-CTF - 200 Combination temperature /humidity - 40…+ 125 °C, 0…100 %rF 200 mm Duct ExCon-D RedCon-D zone 1, 2, 21, 22

Type Function Range Sensor length Main use Connectable to Installation area

Sensors, for ExCon-D and RedCon-D transducer

Type Technical data


InPro-…Only for use with

InCon-D… transducers !NOT for use in

Ex area !

Industrial

Sensors, for InCon-D transducerType Function Range Sensor length Main use Connectable to Installation area InPro-CT - 50 Temperature sensor - 40…+ 125 °C 50 mm Room/duct InCon-D safe areaInPro-CT - 100 Temperature sensor - 40…+ 125 °C 100 mm Duct InCon-D safe area InPro-CT - 150 Temperature sensor - 40…+ 125 °C 150 mm Duct InCon-D safe area InPro-CT - 200 Temperature sensor - 40…+ 125 °C 200 mm Duct InCon-D safe area InPro-CF - 50 Humidity sensor 0…100 %rF 50 mm Room/duct InCon-D safe area InPro-CF - 100 Humidity sensor 0…100 %rF 100 mm Duct InCon-D safe area InPro-CF - 150 Humidity sensor 0…100 %rF 150 mm Duct InCon-D safe area InPro-CF - 200 Humidity sensor 0…100 %rF 200 mm Duct InCon-D safe area InPro-CTF - 50 Combination temperature /humidity - 40…+ 125 °C, 0…100 %rF 50 mm Room/duct InCon-D safe area InPro-CTF - 100 Combination temperature /humidity - 40…+ 125 °C, 0…100 %rF 100 mm Duct InCon-D safe area InPro-CTF - 150 Combination temperature /humidity - 40…+ 125 °C, 0…100 %rF 150 mm Duct InCon-D safe area InPro-CTF - 200 Combination temperature /humidity - 40…+ 125 °C, 0…100 %rF 200 mm Duct InCon-D safe area

MFK Mounting flange for duct-installation, for variable depth of immersion TH-VA Probe made of stainless-steel, length 120 mm, other lengths on request FA-VA Filter-set made of stainless-steel, pore-size 10 µm. Not suitable for high-humidity measurements! MKR Mounting bracket for installation on round air-ducts (diameter up to 600 mm)

EUR/unit 119,– 129,– 139,– 149,– 219,– 229,– 239,– 249,– 319,– 329,– 339,– 349,–

EUR/unit 99,– 109,– 119,– 129,– 199,– 209,– 219,– 229,– 299,– 309,– 319,– 329,–

EUR/unit 39,– 49,– 49,– 39,–

Price list 2008

www.schischek.com

1


RedCon - A…




ExCon-A/RedCon-A/InCon-A Temperature /humidity transducer

ExCon - A…

Explosion proofzone 1, 2, 21, 22


II2(1)G Ex ema [ia] IIC T6II2(1)D Ex tD A21 [iaD] IP66 T80°C

ATEX 94/9/EC

Basics for all …Con-A transducerNo additional module in the panel required !No intrinsically safe wiring required.24 VAC/DC supplyConnector for 1 ExSens sensor for room or duct mounting.0... 10 VDC, 4 ... 20 mA selectable on siteInput: Pt 100, Pt 1000, Ni 100, 200, 1000Resistance 0 ...1000 Ohm, 0 ...10.000 Ohmmeasuring range adjustable.Actual value indication (which can be switched off).All parameters can be adjusted on site without additional tools and measurement devices.Aluminium housing IP 66Integrated terminal boxDimensions (L × W × D) 177 × 107 × 66 mmExCon-A for zone 1, 2, 21, 22RedCon-A for zone 2, 22InCon-A for safe area

DescriptionExCon-A, RedCon-A and InCon-A trans-ducer together with modulating ExSens passive sensors are for temperature or humidity measurement in HVAC systems.Delivery: 1 transducer with connection for modulating 1 ExSens sensorRequired accessory (additional price): 1 ExSens sensorPurchase example for measuring of tem-perature in air duct, with Pt 100 in zone 1.Types to purchase:1 x ExCon-A (Ex-i transducer)1 x TFR-2G (Ex-i sensor)

ExCon - A Module to connect 1 modulating ExSens sensor for temperture or humidity for use in hazardous areas zone 1, 2, 21, 22 zone 0, 1, 2, 20, 21, 22

Type Technical data Installation module Installation sensor*ExCon-A Transducer for passive sensors for zone 1, 2, 21, 22

Ex/RedCon - AA Module as before, but with 1 intrisically safe circuit 4…20 mA output to connect external actual value indicator InCon - A Module as before, but with one 4…20 mA output to connect external indicator EXC-RIA-261 Intrinsically safe actual value LCD indicator, for use in zone 1, 2, 21, 22, connectable to Ex/RedCon-…A sensors NOC-RIA-261 Actual value LCD indicator, for use in safe area, connectable to InCon-…A sensors MKR Mounting bracket for installation on round air-ducts (diameter up to 600 mm)

Type Technical data


RedCon - A Module to connect 1 modulating ExSens sensor for temperture or humidity for use in hazardous areas zone 2, 22 zone 0, 1, 2, 20, 21, 22

Type Technical data Installation module Installation sensor*RedCon-A Transducer for passive sensors for zone 2, 22

Features of ExCon-A, RedCon-A, InCon-AExplosion proof

* in acc. with certification of sensor !

* in acc. with certification of sensor !

Industrial

InCon-A Transducer for passive sensors for safe areaType Technical data Installation module Installation sensorInCon - A Module to connect 1 modulating sensor for temperture or humidity for use in safe area safe area safe area Sensors: all passive sensors like Pt 100, Pt 1000, Ni 100, 200, 1000

InCon - A...

InCon sensors are NOT Explosion proof


IP66

EUR/unit 399,–

EUR/unit 379,–

EUR/unit 359,–

EUR/unit 99,– 89,– 499,– 479,– 39,–

Price list 2008

www.schischek.com 1


ExLine Ex-transducer with Ex-i circuit for zone 0, 1, 2, 20, 21, 22

EXL-IMU-1

Explosion proofzone 0, 1, 2, 20, 21, 22


II(1)GD [EEx ia] IICATEX 94/9/EC

Basics EXL-IMU-1Transducer for passive, potential free, modulating sensors series ExSens. 2-3-4-wire connection24 VAC/DC supplyOutput: 0…10 VDC, 4…20 mAInput: Pt 100, Pt 1000, Ni 100, 200, 1000Resistance 0…1000 Ohm, 0…10.000 OhmDisplay for adjustment and actual value indicationModule must be installed in the safe area, sensor in the hazardous area.

DescriptionEXL-IMU-1 module with intrinsically safe circuit to change a passive sensor signal (e.g. Pt 100) into an active mA/VDC signal.

Delivery: 1 Ex-i module for DIN rail mounting

Accessory (optional): modulating sensors type ExSens

Module

Features EXL-IMU-1

EXL-IMU-1 1 module (rail mounting) for 1 passive sensor series ExSens Safe area zone 0, 1, 2, 20, 21, 22Optional:N1 supply unit Input 120...230 VAC, output 24 VDC, max. 0,5 A, max. 4 pcs. EXL-IMU-1 connectable. N1 supply unit is required only in case of 120..230 VAC supply ! * in acc. with certification of sensor !

Type Technical data Installation module Installation sensor*EXL-IMU-1 transducer

Explosion proof

ExSens Passive modulating sensors for zone 1, 2, 22

ExSens

Explosion proofzone 1, 2, 22

gas + dustManufacturer certificate

ATEX 94/9/EC

Basics for ExSens sensorsSensors for installation in hazardous areas, connected to a relevant transducer, e.g. ExCon-A, RedCon-A or EXL-IMU-1.The transducer changes the passive resistance signal into an acitve 0...10 VDC/4...20 mA signal.

DescriptionExSens sensors for temperature, humidity or pressure measurement in hazardous areas with manufacturer certification in acc. with ATEX 94/9/EC. The sensors are passive and potential free.

Delivery: 1 SensorPurchase example: for 1 room humidity sensorType to purchase: 1 × FFR-2G

passive

Explosion proof Features modulating ExSens sensors

TFR-2G Room temperature - 30…+ 60 °C Pt 100 DIN EXL-IMU-1, ExCon-A, RedCon-A 1, 2 TFR-2G3D Room temperature (IP65) - 40…+ 60 °C Pt 100 DIN EXL-IMU-1, ExCon-A, RedCon-A 1, 2, 22 TFK-2G3D Duct temperature (IP65), 200 mm - 30…+ 150 °C Pt 100 DIN EXL-IMU-1, ExCon-A, RedCon-A 1, 2, 22 TFK-2G3D-400 Duct temperature lenght 400 mm - 30…+ 150 °C Pt 100 DIN EXL-IMU-1, ExCon-A, RedCon-A 1, 2, 22 TFT-2G3D Probe temperature (IP65), 100 mm - 30…+ 150 °C Pt 100 DIN, tubing G1/2“ Ms EXL-IMU-1, ExCon-A, RedCon-A 1, 2, 22 TFT-V4A-2G3D Probe temperature (IP65), 100 mm - 30…+ 150 °C Pt 100 DIN, tubing G1/2“ VA EXL-IMU-1, ExCon-A, RedCon-A 1, 2, 22 TFM-2G3D-3 Mean value temperature 3 m - 30…+ 80 °C Pt 1000 DIN EXL-IMU-1, ExCon-A, RedCon-A 1, 2, 22 TFR-AN-2G3D Room temperature direct contact - 30…+ 150 °C Pt 100 DIN EXL-IMU-1, ExCon-A, RedCon-A 1, 2, 22 FFR-2G Room humidity 30…100 %rF 0…1kΩ EXL-IMU-1, ExCon-A, RedCon-A 1, 2 FFK-2G Duct humidity 30…100 %rF 0…1kΩ EXL-IMU-1, ExCon-A, RedCon-A 1, 2 TFFR-2G Room combination temp./humidity 30…100 %rF, -10…+60 °C 0…1kΩ,Pt100 2× EXL-IMU-1, 2× ExCon-A, 2× RedCon-A 1, 2 TFFK-2G Ductcombinationtemp./humidity 30…100%rF,-20…+60°C 0…1kΩ,Pt100 2× EXL-IMU-1, 2× ExCon-A , 2× RedCon-A 1, 2 DFK-07-2G-FP Differentialpressure(IP65) ∆P<700Pa x…yΩ EXL-IMU-1 1, 2 DFK-17-2G-FP Differentialpressure(IP65) ∆P<1700Pa x…yΩ EXL-IMU-1 1, 2 VFK-07-2G-FP Volume control (IP65) 0…15 m/s x…yΩ EXL-IMU-1 1, 2 SGR-2G Potentiometer Resistance 0…1kΩ EXL-IMU-1, ExCon-A, RedCon-A 1, 2

Type Function Measuring range Sensor Connectable to transducers Sensor in zone

Sensors, connectable to ExCon-A, RedCon-A and EXL-IMU-1 transducer

EUR/unit 395,–

99,–

EUR/unit 99,– 140,– 125,– 150,– 125,– 185,– 250,– 130,– 445,– 445,– 569,– 499,– 990,– 1.035,– 1.035,– 150,–

Price list 2008

www.schischek.com

0


TBR-2G Room thermostat 0…+40°C, 1K Contact, 2-pos EXL-IRU-1 1, 2 TBR-2G3D Room thermostat (IP65) -35…+30 °C, 2-20 K Contact, 2-pos EXL-IRU-1 1, 2, 22 TBR-2-2G Room thermostat 2 stage -30…+60 °C, 2-10 K 2× Contact, 2-pos EXL-IRU-1 1, 2 TBR-AN-2G3D Room temperature direct contact -30…+60 °C, 2-20 K Contact, 2-pos EXL-IRU-1 1, 2, 22 TBK-2G Duct thermostat (IP65) 0…+65°C, 2-20 K Contact, 2-pos EXL-IRU-1 1, 2 TBT-2G Probe thermostat (IP54) 20…+90 °C, 2-20 K Contact, 2-pos L = 120 mm EXL-IRU-1 1, 2 TBT-VA-2G Probe thermostat with VA sleeve 0…+90°C, 3K Contact, 2-pos V4A EXL-IRU-1 1, 2 TBK-FR-2G Frost protection thermostat (IP65) -10…+12 °C Contact, 2-pos capillary 6 m EXL-IRU-1 1, 2, FBR-2G Room humidistat 35…100 %rH, ~ 4 %rH Contact, 2-pos EXL-IRU-1 1, 2 FBK-2G Duct humidistat 35…100 %rH, ~ 4 %rH Contact, 2-pos L = 180 mm EXL-IRU-1 1, 2 DBK-2G Differential pressure 20-300, 50-500, 100-1.000 Pa Contact, 2-pos EXL-IRU-1 1, 2 DBK-2G3D Differential pressure (IP65) 40-125, 100-400, 350-1.400 Pa Contact, 2-pos EXL-IRU-1 1, 2, 22 WFBK-2G Air paddle 2…8 m/s, paddle V2A Contact, 2-pos EXL-IRU-1 1, 2 SWBT-2G liquid flow switch -20…+60 °C Contact, 2-pos EXL-IRU-1 1, 2 NBW-K-2G Fanbeltprotection(IP65) upto<20.000m³/h Namursensor+bracket EXL-IRU-1 1, 2 NBW-G-2G Fanbeltprotection(IP65) morethan>20.000m³/h Namursensor+bracket EXL-IRU-1 1, 2

Type Function Range Sensor Information Connectable to module type Sensor in zone

Sensors, connectable to switching module type EXL-IRU-1

ExLine Ex-switching module for potential free, binary signals in zone 0, 1, 2, 20, 21, 22

EXL-IRU-1 Explosion proof zone 0, 1, 2, 20, 21, 22 gas + dust PTB-certifiedII(1)GD [EEx ia] IIC

ATEX 94/9/EC

Basics EXL-IRU-124 VAC/DC supplyInput: passive potential free binary sensor.Output: potential free contact in the safe areaIntegrated time running relais 30...120 sec.2 LED to show switching position.DIN rail mounting.Module must be installed in the safe area, sensor in the hazardous area.

DescriptionEXL-IRU-1 module with intrinsically safe circuit to change a passive potential free binary signal (e.g. contact) into a contact in the safe area.

Delivery: 1 Ex-i module for DIN rail mounting

Accessory (optional): binary sensors type ExSens

EXL-IRU-1

Features EXL-IRU-1 module

EXL-IRU-1 1 module (rail mounting) for 1 passive binary sensor series ExSens Safe area zone 0, 1, 2, 20, 21, 22 Optional:N1 supply unit Input 120...230 VAC, output 24 VDC, max. 0,5 A, max. 4 pcs. EXL-IRU-1 connectable. N1 supply unit is required only in case of 120..230 VAC supply ! * in acc. with certification of sensor !

Type Technical data Installation module Installation sensor*EXL-IRU-1 switching module

ExSens passive binary sensors for zone 1, 2, 22

ExSens Explosion proof zone 1, 2, 22 gas + dust

Manufacturer certification

ATEX 94/9/EC

Basics for binary ExSens sensorsSensors for installation in hazardous areas, connected to a switching module type EXL-IRU-1.The module changes the passive binary signal into a contact in the safe area.Sensor must be installed in the hazardous area, module in the safe area.

DescriptionExSens binary sensors for temperature, humidity or pressure measurement in hazardous areas with ma-nufacturer certification in acc. with ATEX 94/9/EC. The sensors are passive and potential free.

Delivery: 1 SensorPurchase example: for 1 frost protection thermostatType to purchase: 1 × TBK-FR-2G

binary passive

Explosion proof Features ExSens sensors

Explosion proof

Installation kit 1 for frost protection sensor type TBK-FR-2G, PG entries for capillary, 6 brackets, support bracket Installation kit 2 includes 2 meter pressure hose (inner diameter Ø 6 mm) 2 plastic fittings

Type Technical data


EUR/unit 89,– 99,–

EUR/unit 130,– 185,– 220,– 220,– 150,– 160,– 240,– 150,– 160,– 285,– 125,– 295,– 145,– 250,– 110,– 135,–

EUR/unit 28,– 15,–

Price list 2008

www.schischek.com 1


EXC-T... Thermostat II2G EEx ed IIC T6 -30…+70 °C, different ranges and types EXC-TF... Frostprotectionthermostat II2GEExedIICT6 +4…+15°C,∆T=2K,capillary6m EXC-R 10/3... Switch II2G EEx ed IIC T6 10 A - 230 /400 V - 2,5 /4,6 KW - 3 pole EXC-R 20/3... Switch II2G EEx ed IIC T6 20 A - 230 /400 V - 4,5 /9,0 KW - 3 pole EXC-R 20/6... Switch II2G EEx ed IIC T6 20 A - 230 /400 V - 4,5 /9,0 KW - 6 pole EXC-R 40/3... Switch II2G EEx ed IIC T6 40 A - 230 /400 V - 11 /20 KW - 3 pole EXC-R 40/6... Switch II2G EEx ed IIC T6 40 A - 230 /400 V - 11 /20 KW - 6 pole EXC-R 80/3... Switch II2G EEx ed IIC T6 80 A - 230 /400 V - 23 /40 KW - 3 pole EXC-R 80/6... Switch II2G EEx ed IIC T6 80 A - 230 /400 V - 23 /40 KW - 6 pole EXC-RIA-261 Actual value indication II2G EEx ia IIC T6 4...20 mA, loop powered EXC-… Smoke detector, duct / room II2G EEx m II T4 24 VDC, incl. terminal boxEXC-DS1/VA Safety temperature sensor II2G EEx d IIC T6 Duct mounting, potential free contact, switching at 70°C…160°C (10°C steps)

ExComp Explosion proof zone 1, 2, 21, 22

(in acc. to type) gas + dust PTB-certified

ATEX 94/9/EC

Basics ExCompNo specific information.Data in acc. with every single product / type

DescriptionDifferent explosion proof products like switches, frost protection thermostats, ....

Delivery: 1 componentPurchase example: Switch 20 A, 6 poleType to purchase: 1 × EXC-R 20/6

Components

Type Application Explosion proof Technical data

ExComp components

EXM - 650 650 N 24 VDC Magnet 44 mA Zone 1, 2, 21, 22 EXM -1300 1.300 N 24 VDC Magnet 65 mA Zone 1, 2, 21, 22 EXM -2000 2.000 N 24 VDC Magnet 160 mA Zone 1, 2, 21, 22

Type Force Supply Function Current Installation in

ExMag magnets

GH - 6 Anchor for EXM-650 GH - 13/20 Anchor for EXM-1300 and EXM-2000 EXC-K4 Ex-e terminal box, IP 66 EXC-K4/S Ex-e terminal box, IP 66, with integrated fuse EXC-T1 Ex-d push button MOL-230/24 Supply unit, input 230 VAC, output 24 VDC, max. 350 mA, DIN rail mounting

Type Technical data


ExMag Ex-doorholder magnets for zone 1, 2, 21, 22

ExMag Explosion proof zone 1, 2, 21, 22 gas + dust PTB-certified

II2G Ex mb II T6II2D Ex tD 21IP65 T80°C

ATEX 94/9/EC

Basics ExMagExMag electric magnets. Force in acc. with type1 m cableAn Ex-e terminal box is required for electrical connection. We recommend a stabilised 24 VDC power supply. The max. AC-ripple must not exceed 20%.

DescriptionExMag doorholder magnets are electric magnets to keep doors open or closed as long as supply voltage is available.

Delivery: 1 magnet + accessoriesPurchase example: 650 N magnet + anchor + Ex-terminal boxType to purchase: 1 × EXM-650 + 1 GH 6 + 1 × EXC-K4

Magnet

Explosion proof Features ExMag magnets

ExComp Different Ex-componentsExplosion proof Features ExComp components

EUR/unit 375,– 520,– 555,–

EUR/unit 23,– 34,– 37,– 95,– 165,– 165,–

EUR/unit 520,– 550,– 270,– 305,– 510,– 475,– 710,– 895,– 1.520,– 499,–on requ. 185,–

Price list 2008

www.schischek.com

1. Scope of application and contracting1.1. The following terms and conditions are applicable for deliveries and/or services (hereinafter called “deliveries”) rendered by corporations forming part of the Schischek GmbH (each of such corporations hereinafter called “Schischek”) insofar as no special terms for specific deliveries are is-sued by Schischek. General terms and conditions of the Purchaser shall apply only where expressly accepted in writing by Schischek. Side agreements must be made in writing to be effective.1.2. The offer issued by Schischek is non-binding. The Purchaser is bound to his order for 4 (four) weeks after placing the order. The contract shall be concluded by our confirmation of the order exclusively.1.3. The copy right of any construction plans, illustrations, schemata, connecting diagrams or any other documentaries remains with us. Publishing or copying, even partial, is not allowed without the prior written approval of Schischek.1.4. Apparent error on the part of Schischek shall lead to retroactive invalidity of the contract.2. Prices, Payment 2.1. The list prices of Schischek at the time of delivery shall be charged if not otherwise agreed upon by the contracting parties.2.2. All prices are quoted ex works (INCOTERMS 2000), manufacturing entity of Schischek, without packaging or insurance plus the current value added tax.2.3. The packaging will be provided according to our best judgement. The Purchaser shall additio-nally carry the costs of any special request.2.4. All circuit diagrams, adjustments, assembly of equipment etc. are special services even if they are performed within the premises of Schischek and shall be invoiced separately. They shall be charged either through a flat rate or through the actual expenditure plus travel costs and allo-wances. 2.5. The Purchaser shall pay the invoices of Schischek free of charge and/or fee within 10 (ten) days of the invoice date minus 2% (two) discount or net within 30 days of the invoice date. Invoices for services only (e.g. for repairs) are to be paid net cash within 10 (ten) days.2.6.Surcharges for any work carried out at Purchaser’s request on Sundays, holidays, as well as overtime, will be borne by the Purchaser. Preparations, travel, waiting and home to site time shall be invoiced equally as work time.2.7. No transfer of Purchaser’s rights or claims against Schischek to third parties shall happen without Schischek’s prior written approval.2.8. The Purchaser may set off only such claims as are undisputed or have become res judicata. The Purchaser may not assign rights against Schischek to third parties without the prior written approval of Schischek.3. Delivery, Transfer of Risk, Delay3.1. The time of delivery begins with conclusion of the contract and complete clarification of kind and range of the supplies.3.2. If the dispatch or the delivery is delayed due to reasons imputable to the Purchaser, or if the Purchaser for other reasons is in default of acceptance, then the risk shall pass to the Purchaser.3.3. If any delay in delivery occurs due to reasons beyond Schischek’s control the delivery period will be prolonged for at least this period of delay.3.4. For delay of the payment in due time the Purchaser owes interests at a value of 8% over the current valid interest basis of the EZB. 3.5. Penalties for delay in delivery must be agreed upon expressly in writing to have legal effect.3.6. The Purchaser shall not refuse the acceptance of supplies for minor default. Partial deliveries are permissible, insofar as not otherwise agreed upon by the contracting parties in writing. 3.7. Any exportation of the supplies can be subject to Governmental Approval. Our contractual obligation is valid subject to the pre-requisite of the existence of such permission.4. Warranty4.1. The Purchaser will examine the goods immediately after arrival at the place of delivery and will indicate material defects immediately to Schischek in writing.4.2. Deliveries, which show defects at the time of the Transfer of Risk, will be repaired according to the standard work time of Schischek or replaced by faultless material at Schischek’s choice without cost to the customer. If the repair or replacement fails, the Purchaser can require a reduction of Price or revoke the contract. Clauses 5.3 to 5.7 shall apply regarding claims for damages. 4.3. The warranty period shall be 12 months after the Transfer of Risk. This does not apply to longer periods imposed by compulsory law. The legal regulations regarding inhibition or new beginning of the time periods remain unaffected. 4.4. The Purchaser can hold back payments for warranty reason only to an extent, which is ap-propriate in relation to the material defects and then only if he made notice of a warranty claim over which no doubt can exist. If the warranty claim was unjustified, the Purchaser shall reimburse Schischek for the accrued expenses.4.5. Warranty claims for insignificant deviation from the agreed upon conditions and during natural wear are excluded. Furthermore such claims are excluded in case of damage, after the Transfer of Risk, due to incorrect treatment, excessive use, unsuitable utilities, incorrect build-lateral conditions or technical data given by the Purchaser, or because of special outside influences which are con-tractually not presupposed. There shall be no warranty in case of inappropriate changes or repairs are made by the Purchaser or third parties.

4.6. Other or further warranty claims apart from those stipulated under number 4 are excluded.4.7. If not otherwise expressly stated by the client, the client’s request for subsequent improvement shall include his declaration of the fact that he always wishes the removal of the defect as to quality or not. The fact that we are prepared to perform and the performance itself shall not be considered as an acknowledgement of the existence of a defect as to quality. If during the performance of such a removal it comes out that the defect of deviation is not caused by a defect as to quality, the client shall bear the costs for the removal (in case of mutual responsibility, the costs shall be borne proportionally).5. Claims for damages, Rescission of Contract 5.1. If and insofar as the Purchaser suffered damage due to Schischek’s failure to comply to an agreed delivery date, he can claim damages for each completed week of the delay of 0,5 % up to a extent of in whole 5 % of the value of that part of the supply concerned, which because of the delay cannot be used. Claims for damages due to delay of the supply as well as claims for damages instead of the achievement, which go beyond the limits specified in sentence 1, are excluded. This applies even after expiration of an additional respite for delivery set against Schischek. The Purchaser can only withdraw by law from the contract, if and insofar as the delay was imputable to Schischek.5.2. Should the delivery become finally impossible through the fault of Schischek, the Purchaser is entitled to claim for damages. The claim for damages is limited to 5 % of the value of that part of the supply, which because of the impossibility cannot be used. The right of the Purchaser to revoke the contract by law remains unaffected.5.3. Schischek shall be liable by law for any personal injury and shall compensate the real damage suffereduptotheamountof€100.000,00foreachdamageincidentuptonomorethanatotalamountof€1.000.000,00.Compensationforthereplacementofdataand/orinformationshallbeexcluded.5.4. Further compensation of damages and costs suffered by the Purchaser (hereinafter: “Claims for Damages”), irrelevant on whatever legal grounds, including but not limited to violation of obliga-tions resulting from contract or law, shall be excluded.5.5 The limitation of the rights of the Purchaser according to Clauses 5.1 up to 5.4 shall not apply insofar as the liability is imposed by compulsory law, e.g. for product liability, for intention, for gross negligence, for bodily injury and for breach of a taken over guarantee as well as of substantial contract obligations, however in the latter case only for the contract-typical foreseeable damage.5.6. Claims for damages under Clause 5 shall expire upon expiration of the warranty period in ac-cordance with Clause 4.3. This does not apply in case of liability for intention, for gross negligence, for bodily injury or for liability resulting from product liability law. 5.7. A change of the burden of proof to the disadvantage of the Purchaser is not implied by the preceding regulations.6. Redemption of Goods 6.1. A non-contractual return of goods requires the previous written approval of Schischek. In case of such approval, the Purchaser owes a logistic lump sum of 20% of the invoice amount and has to return the goods to Schischek in the original/new condition with original packaging.6.2. We shall have the right to dispose of or utilize otherwise without compensation any items which the client has sent to us in order to have facts or costs determined and which have not been collected after 30 days after our request despite our request to do so.7. Retention of title7.1. The supplied goods remain the property of Schischek until complete payment and have to be returned upon Schischek’s first request until payment is fulfilled.7.2. Until passage of title the Purchaser is not allowed to use the goods and is obliged to treat the goods in a good manner, to protect against damage and to store in a dry and non condensing place and to insure the original value at own expense.7.3. Pledging, transfer of title for mortgage and resale of Schischek’s property is forbidden. Access of third parties to Schischek’s property is to be reported to Schischek immediately and must be forcefully prevented. The Purchaser bears any costs of intervention on the part of Schischek.7.4 In case of imminent bankruptcy/insolvency or similar events and the assumption of our property or attempted control by third parties, Schischek shall be notified immediately.8. Spare parts, environmental protection 8.1 Unless otherwise stated in the product information no periods are fixed, Schischek keeps available spare parts for wearing parts and replacements frequently required for maintenance (spare parts) for an appropriate period of time insofar as in special cases (e.g. expiry of IT compo-nents) and at the end of the period specified in number 4.3 the source of supply of Schischek does not precipitate. Schischek can also offer examined used parts as spare parts if required, or other function-receiving technical solutions.9. Place of jurisdiction 9.1. The place of jurisdiction for all legal disputes resulting from contracts referring to these General Conditions and from agreements regarding the performance of such contracts is Nuremberg.9.2. The legal relationship between the Parties shall be governed by the laws of the Federal Re-public of Germany, excluding the UN law regarding contracts over the international sale of goods (CISG).

General Conditions for the Supply of Products and Services of the Schischek GmbH

Last update: 2007.10.21

www.schischek.com

Information about electrical explosionproof according ATEX 94/9/EC

Explosion protection regulations in the EU member states are marked by the change of EU protection guideline 67/117/EWG ff to the two new EU guide-lines 94/9/EC (ATEX 95) and 95/C 332/06 (ATEX 137). As a result of the new directives, explosion protection in European regulations there will be a harmonisation of standards. There will be a tran-sitional period to adjust from the „old“ to the „new“ European law. The regulations covering the „old” law were in effect up to June 30th 2003.Since July 1st 2003, electric explosion proof equipment must comply with ATEX Ex-protection guidelines in accordance with 94/9/EC – on the approximation of the laws of the Member States concerning equipment and protective systems for use in potentially explosive atmospheres.Information on uniform classification of potentially explosive systems and how to use this as a basis for selecting and classifying systems and equip-ment, incl. their installation, can be found in guide-line 1999/92/EC (ATEX 137).ATEX: Guideline 94/9/EC of the European par-liament and the Council from March 23rd 1994 brought the legislation of the member states, con-cerning equipment and protective systems for use in explosion risk areas, into line.ExVO: Directive on the distribution of equipment and protection systems for potentially explosive are-as – explosion protection prescription - 11.GSGV.ElexV: Operational Safety regulation, minimum re-gulation in order to improve health-safety and secu-rity of employees at hazardous workplaces !CertificatesCorresponding approvals and certificates are re-quired for electrical explosion proof equipment. Te-sting must be carried out by an official testing agen-cy (for example the PTB - Physikalisch Technische Bundesanstalt in Braunschweig /Federal German Physical and Technical Institute of Braunschweig). ATEX approvals are also accepted in many coun-tries and states outside Europe.ResponsibilitiesThe responsibility for compliance with all regulati-ons and guidelines, from production to planning, up until installation, operation and maintenance, has greatly increasedEach individual must be conscious about the fact that he accepts personal responsibility as part of a total project:

building ownerend-userarchitectconsulting engineer /control companyinspection authoritycontractor / installermanufacturerproduct suppliermaintenance engineers

•••••••••

The type plate and its componentsFrom 1/7/2003 the new ATEX guidelines come into force. The then current legal bases for the certifica-tion and labelling of electric explosion proof equip-ment is the EC guideline:Example, for the labelling of a quarter turn actuator:Manufacturer’s name, manufacturer’s address, de-signation of type, electrical data (V, A, W, Hz) am-bient temperature if different from - 20 to + 40°C, unit serial number, in addition to the classification of Ex protection.

For the installation of electrical systems in areas with explosive gas atmospheres of group II, rule IEC 60 079-14 (EN 60079-14) will apply.Electric circuits of protection types d, e, q, o, m, pInstallation in the panel is identical to ”standard” installation, however the procedures for connecting Ex equipment must be followed. This refers, for ex-ample to voltage, current, fuses and motor protec-tion equipment, etc. The requirements for specific products must be taken from their corresponding test certificates, standards and prescriptions as well as from the guidebook. It is only permitted to work on electric circuits within the Ex-area (for ex-ample when connecting to Ex-e terminal box if the voltage has been switched off). An Ex-e terminal box should only be opened after the voltage has been switched off.Electric circuits of protection type „i“ (intrinsically safe)For the planning and operation of switchgears and control systems installed in the safe area, but which contain circuits leading into the Ex-area, certain requirements should be considered. This applies especially to intrinsically safe circuits. Intrinsical-ly safe circuits and non-intrinsically safe circuits should be kept separate. Minimum distances (di-stances) between bare connections must be obser-ved, the cables must not produce any inadmissible external inductance or capacitance. The maximum admissible electrical limits of Ex-i equipment must be observed at all times. Intrinsically safe and non-intrinsically safe electrical circuits should not cross, however it is allowed between two intrinsically safe circuits. Intrinsically safe circuits must be clearly marked. Intrinsically safe circuits are marked by a “light blue” color. This color is recommended for all

Correct installation

intrinsically safe circuits to prevent confusion and/or linking up to a non-intrinsically safe circuit. Ex-amples: cabels, cables, cable conduits, dampers, connection boxes, cable connectors,...A minimum distance of 50 mm should be allowed between intrinsically safe and non-intrinsically safe circuits, and a minimum distance of 6 mm between two different intrinsically safe circuits. During instal-lation the cables of intrinsically safe and non-intrin-sically safe circuits should be laid out separately !Suggestion on how to create a pannel It is necessary to keep intrinsically safe and non-intrinsically safe equipment separate. It is recom-mended, in this case, that a sufficient distance be kept, to avoid extra costs in the future. Large transformers, frequency rectifiers, large relays and other electric equipment that may in-fluence intrinsically safe circuits by inductance or capacitance should be installed at a sufficient distance. As a precaution Ex-i equipment should have a suitable cover to protect it from incorrect handling. The appropriate standards and regulati-ons must be observed.

ATEXAtmosphèreExplosible

Regulations for explosion protection The type plate and its components

www.schischek.com

Price list 2008

Information about electrical explosion-proof according ATEX 94/9/ECClassificationandlabellingofexplosionproofareas Classificationofareas,haz.duetoflamm.gases,vapours,mists

www.schischek.com

Price list 2008

Where and when do I have to take explosion proof into consideration?Explosion proof means: „Preservation of Life. Health. Basic values“

When can a danger of explosion occur?A danger of explosion occurs when a flammable medium (gas, vapor, mist or dust) in a dangerous quantity is present.What creates an explosion?An explosion may occur when the following 3 com-ponents are present at the same time:

Explosive atmosphereSource of ignitionAir (oxygen)

Typical sources of ignitionVery often the reason for accidents is self-ignition, extraordinary surface temperatures and sparks due to mechanical reasons. But there are also a lot of other sources of ignition, caused by either mecha-nical and/or electrical equipment. These are for example:

Self-ignitionExtraordinary surface temperaturesOpen flamesSparks caused by mechanical reasonsStatic electricityLightning strikeUltra-sonicChemical sources of ignitionElectric sparksElectric arcsAdiabatic compressionAdiabatic shock wavesElectric balancing power

•••

•••••••••••••

Is your system safe?We have the following situation NOW or in the FUTURE:Yes.No (Please check) Flammable materials are stored. Flammable materials are used. Flammable materials are bottled. Flammable materials are used during the cleaning process. Flammable materials are used in the production process. Flammable materials will be produced during the production process.

6 x „No“: Obviously you do not need explosion proof

at least 1 x „YES“: When planning you have to consider rules, regulations and instructions concerning explosion proof

Example: BetrSichV, ExVO, EX-RL

Remarks: All information, tables, checklists and further docu-mentation are only for your assistance and do not claim to be complete. In no way do they replace official regulations and rules or even laws by the authorities. We want to point out that it is very important to undertake all measures for an exact classification of the Ex-area.

Typical Applications:Chemical, pharmaceutical and industrial plantsRefineries, petrol depots, gas stationsPaint and solvent shopsDrying and coating cabinetsLaboratories in industry and schoolsWater treatment works, power plantsCompressor stations, gas worksAll kinds of storekeeping and stocksAll kinds of filling stationsAll kinds of cleaning stationsMills, silos, silos for bulk goodsOffhore and onshoreOil and gas pipelinesPrinting works, food industry, …

Schedule:Analyse whether you need explosion proof

or notAsk experts in order to analyse the risk

of danger Define zones, areas, categories, explosion

groups and temperature classesPlanning according to all necessary rules

and regulationsChoose the best supplier and the right productKeep to the installation rulesCheck the labelling of the equipmentMake sure that the appliance will be put into

operation correctlyConfirm a final inspection by the responsible

authorityGuarantee regular and correct maintenance

according to the regulationsThe correct documentation has to be maintained

From fire to detonationEffect and reaction velocity increase significantly from fire, outburst flame, via ignition and explosion up to detonation. Explosions are more likely with gaseous media and detonations by dust media.

••••••••••••••

•

•

•

•

••••

•

•

•

www.schischek.com

Price list 2008

Zones • Explosion groups • Temperature classesClassificationandlabellingofexplosionproofareasImplementation

Potentially explosive areas should be divided into zones, and the equipment should be divided into groups and categories. The labelling on the iden-tification plate of certified equipment indicates in which zone the explosion proof equipment can be used.Division into product groupsGroups are divided into group I and group II. Group I consists of mining „underground“ and group II deals with prevention of gas and dust explosion protection for all other applications.Division into zonesPotentially explosive areas are divided into six zones, according to time-related and local probabi-lity, that a potentially explosive atmosphere (p.e.a.) exists. A distinction is made between combustible gases, mists, vapors and combustible dust. The zones are described in the accompanying table.Gases, mists and vapors are placed in zones 0, 1 and 2, whereby the requirements for the chosen equipment increase from zone 2 to 0. Equipment in zone 0 must be built in a way „that even if a type of protection fails or if two faults occur, that sufficient explosion protection is guaranteed“. Therefore for example a passive, potential free sensor, installed in zone 0, and connected to an intrinsically safe electric circuit (II2(1)G [EExia] IIC), must display current approval.Zones 20, 21 und 22 are for dust, whereby the requirements for the chosen equipment increase from zone 22 to 20. Equipment in zone 20 and 21 need special approval.Division into product groupsProduct groups determine, in which zones the equipment should be installed. Once again there are six categories. Categories1G, 2G and 3G are classifications for gas explosion protection (G = Gas); to which equipment with 1G for zone 0, 1 and 2, equipment with 2G for zone 1 und 2 and equip-ment with 3G for zone 2 are suited. Categories 1D, 2D and 3D are classifications for dust explosion protection (D = Dust); to which equipment with 1D for zone 20, 21 and 22, equipment with 2D for zone 21 and 22 and equipment with 3D for zone 22 are suited.

Zone 0, 1 and 2

An Example of a typical zone activity would be filling a barrel of petrol in an enclosed area.

Zone 20, 21 and 22

An example of a typical zone activity would be filling agrain silo in an enclosed area.

Explosion groups, temperature classesThe equipment groups and categories determine, in which zones the equipment should be installed, therefore the explosion groups and temperature classes determine, to which mediums inside the zones, the equipment is suited. The type of pro-tection used is not a mark of quality but is instead a constructive solution for selecting equipment for explosion protection.

Division into explosion groupsExplosion proof equipment for gases, mists and vapors is divided into three explosion groups (IIA-IIB-IIC) according to the type of protection being used. The explosion group is a means to measure the ignitability of gases (potentially explosive atmo-spheres). The equipment requirements increase from II A to II C.

Division into temperature classesExplosion proof equipment, installed within the Ex area, is divided into 6 temperature classes (T1 to T6). Temperature class is not – as it is often wron-gly believed – the operating temperature range of the equipment, but the maximum permissible surface temperature of the equipment, in relation to + 40°C ambient temperature on any surface area, and should not be exceeded at any time. The maximum surface temperature must remain below the ignition temperature of the surrounding medium at all times. The equipment requirements rise from T1 to T6.

www.schischek.com

Price list 2008

Air safety dampers • Air control dampers • Fire/smoke dampers Heating • Cooling •Humidification• VAV control

Thermostats • Humidistats • Pressurestats • Filter protection

Application

Fan belt protection • Frost protection

Schischek actuators are approved for direct installation and operation in explosion risk areas, as they are of the highest explosion groups and temperature class and are suitable for all gases, vapors, steam and dust. The electrical connection is made via an explosion proof terminal box (type ExBox-...). Please ensure during installation that all cables are securely fixed and connected in such a way that they are protected from mechanical damage.

Air damper control

In this example the control system consists of an actuator and a ExCon-D transducer with ExPro probe. The combination can be installed directly into the Ex area. The transducer converts the probe signal into an active signal (0...10 VDC or 4...20 mA) for input in a PLC systems. The output signal from the controller goes directly to the actuator.Between sensor and controller is no additionally Ex i module and also no intrinsically safe (IS) wiring methode required.For the actuator and transducer the maximum permissible surface temperatures have to be taken into account.

Heating - cooling control

Automatic air damper control

In this example the control system consists of a valve actuator and an ExCon-D transducer with ExPro probe. The combination can be installed directly into the Ex area. The transducer converts the probe signal into an active signal (0...10 VDC or 4...20 mA) for input in a PLC systems. The output signal from the controller goes directly to the actuator.Between sensor and controller is no additionally Ex i module and also no intrinsically safe (IS) wiring methode required.For the actuator and transducer the maximum permissible surface temperatures have to be taken into account.

Humidity control

In applications for fire/smoke dampers, the actuator has to reliably return the damper to its safety position via an external switch /contact. The actuator will return the damper to its safety position by an internal spring. The contact comes from a safety thermal trigger type FireSafe which is direct connenced to the actuator.

Control of fire /smoke dampers

In this example the control system consists of an actuator and a differential pressure ExCon-P transducer. The combination can be installed directly into the Ex area. The transducer converts the differential pressure signal into an active signal (0...10 VDC or 4...20 mA) for input in a PLC systems. The output signal from the controller goes directly to the actuator. Between sensor and controller is no additionally Ex i module and also no intrinsically safe (IS) wiring methode required. The controller, situated in the safe area will, depending on changing circumstances being monitored, control a fan (must be Ex proof) or a modulating damper actuator (also Ex proof) to maintain the required air volume/pressure.

VAV and differencial pressure control

In this example the control system consists of an actuator and a ExCon-D transducer with ExPro probe. The combination can be installed directly into the Ex area. The transducer converts the probe signal into an active signal (0...10 VDC or 4...20 mA) for input in a PLC systems. The output signal from the controller goes directly to the actuator.Between sensor and controller is no additionally Ex i module and also no intrinsically safe (IS) wiring methode required.For the actuator and transducer the maximum permissible surface temperatures have to be taken into account.

Thermostats are passive switching equipment without any electrical energy supply of their own (type TB...). The switching function is performed mechanically. The integrated switches are within a circuit designed as intrinsically safe by using a switching module (type EXL-IRU-1). The switching module should be installed in the safe area. The output contact can be used for sequence functions (relays, contacts, direct circuit..).

Thermostats

For monitoring fans in hazardous areas, only passive differential pressure switches (DBK-...) or air paddle (type WFBK-...) can be used. The switching function is mechanical and is an intrinsically safe (IS) circuit that is supplied via a switching module (EXL-IRU-1). The switching module must be installed in the safe area. The output function can be used for switching relays, contacts etc. Switching modules to indicate fan failure, are delivered with integrated time running relay with delay on start up.

Drive belt monitoring with differential pressure sensor /air paddle

Hygrostats are passive switching equipment without any electrical energy supply of their own (type FB...). The switching function is performed mechanically. The integrated switches are within a circuit designed as intrinsically safe by using a switching module (type EXL-IRU-1). The switching module should be installed in the safe area. The output contact can be used for sequence functions (relays, contacts, direct circuit..).

Hygrostats

For monitoring fans contact less in hazardous areas, only induc-tive sensors (NBW-...) can be used. The switching function is mechanical and is an intrinsically safe (IS) circuit that is supplied via a switching module (EXL-IRU-1). The switching module must be installed in the safe area. The output function can be used for switching relays, contacts etc. Switching modules to indicate fan failure, with integrated time running relay with delay on start up, monitor the fan shaft rotation via a inductive sensor.

Drive belt monitoring with inductive sensor

For monitoring air filters in hazardous areas, only passive differential pressure switches (type DBK...) can be used. The switching function is mechanical and is an intrinsically safe (IS) circuit that is supplied via a switching module (EXL-IRU-1). The switching module must be installed in the safe area. The output function can be used for switching relays, contacts etc.

Filter monitoring

For frost protection in hazardous areas you can use a frost thermostat (type TBK-...) in the duct together with a switching module ( type EXL-IRU-1). The passive sensor in the hazardous area is connected via an intrinsically safe circuit (IS) to the switching module , mounted in the safe area. The output contact can be used to follow up functions (relays, contacts, ect…).

Frost protection

www.schischek.com

Price list 2008

Sales SingaporeSchischek AGSingapore Representative Office 10, UBI Crescent, 07 - 44UBI Techpark, Lobby ‚C‘Singapore - 408 564Tel. +65 67498494Fax +65 [email protected]

Sales United KingdomSchischek Ltd.Kenmore House,Navigation Road,Chelmsford,Essex.CM2 6HXUnited KingdomTel. +44 1245-256007Fax +44 [email protected] www.schischek.co.uk

Sales FranceSchischek SARL Antidéflagration108 Rue Damrémont75018 ParisFranceTel. +33 1 42526102Fax +33 1 [email protected]

Sales ItalySchischek s.r.l.Via Adelasio 2224020 Ranica (GB)ItalyTel. 39 0 35 4123408Fax +39 0 35 [email protected] www.schischek.it

Manufacturing and Sales EUSchischek GmbHMühlsteig 45Gewerbegebiet V90579 LangenzennGermanyTel. +49 9101 9081-0Fax +49 9101 [email protected] www.schischek.de

Sales worldwide (outside EU)Schischek AGFuchsacker 6789426 LutzenbergSwitzerlandTel. +41 71 8886450Fax +41 71 [email protected]

Headquarter Subsidiaries Subsidiaries

Appointed Distributor

Vibevej 18-266705 Esbjerg Ø

Tlf.: +45 75 12 62 74 Mobil: +45 41 19 26 66 Fax: +45 75 12 42 74 email: [email protected] [email protected]

explosion proof. - velkommen til lauridsen industri · explosion proof. safety for all control...

Documents