fanuc super cap i m operator

7/28/2019 Fanuc Super Cap i M Operator

1/461

TECHNOLOGY AND MORETECHNOLOGY AND MORETECHNOLOGY AND MORETECHNOLOGY AND MORE

GE Fanuc Automation EuropeGE Fanuc Automation EuropeGE Fanuc Automation EuropeGE Fanuc Automation Europe

Super Cap i MSuper Cap i MSuper Cap i MSuper Cap i M

B-63294EN/02B-63294EN/02B-63294EN/02B-63294EN/02

Computer Numerical ControlsComputer Numerical ControlsComputer Numerical ControlsComputer Numerical Controls

Operators ManualOperators ManualOperators ManualOperators Manual


2/461


3/461

s1

SAFETY PRECAUTIONS

When using a machine equipped with FANUC Super CAPi M, the following safety precautions must be

observed.


4/461

B63294EN/02SAFETY PRECAUTIONS

s2

1

WARNING, CAUTION, AND NOTE

This manual includes safety precautions for protecting the user and preventing damege to the

machine. Precautions are classified into Warning and Caution according to their bearing on safety.

Also, supplementary information is described as a Note. Read the Warning, Caution, and Note

thoroughly before attempting to use the machine.

Read this manual carefully, and store it in a safe place.

WARNING

Applied when there is a danger of the user being injured or when there is a danger of both the user

being injured and the equipment being dameged if the approved procedure is not observed.

CAUTION

Applied when there is a danger of the equipment being dameged, if the approved procedure is not

observed.

NOTE

The Note is used to indicate supplementary information other than Warning and Cation.

` Read this manual carefully, and store it in a safe place.


5/461

B63294EN/02 SAFETY PRECAUTIONS

s3

2

GENERAL WARNINGS AND CAUTIONS

WARNING

1 Before attempting to use a conversational function (such as the creation/editing/run of

machining programs, machining simulation, and the measurement of tool compensation),

close the doors of the machine, and apply any other safety measures deemed necessary.

Failure to apply the necessary safety precautions may result in the serious injury, or even death,

of the user or bystanders.

2. Before proceeding to the next step of a procedure, check the display on the screen carefully to

ensure that the data has been entered exactly as intended.

If the machine is operated with incorrect data, the tool may collide with the machine and/or

workpiece, possibly causing damage to the tool and/or machine, or even injury to the user or

bystanders.

3. When the tool compensation function is being used before starting the machine, check the

direction and amount of compensation so that the tool will not collide with the workpiece or

machine.

If the tool collides with the machine and/or workpiece, the tool and/or machine may be

damaged, plus there is the danger of injury to the user or bystanders.

4. After you create a machining program using a conversational function, do not operate the

machine using that program immediately. Instead, perform a machining simulation to ensure

that the tool path and machining operation are satisfactory and that the tool will not collide with

the workpiece or machine (including the jig).



5. After you convert a machining program, created using a conversational function, to NC

program format, do not operate the machine using that program immediately. Instead, confirm

every step of the NC program, and ensure that the tool path and machining operation are

satisfactory and that the tool will not collide with the workpiece or machine (including the jig).

Before starting production machining, operate the machine without a workpiece mounted toensure that the tool will not collide with the workpiece (were it to be mounted) or the machine

(including the jig).



6. Before starting to create a machining program using a conversational function, first check that

all required data within the tool file, cutting condition file, and pretool list, and all parameters

required for the conversational function, is set correctly.

If any of the required data is not set correctly, the cutting conditions will not be set correctly,

possibly resulting in damage to the tool, or even injury to the user or bystanders.


6/461

B63294EN/02SAFETY PRECAUTIONS

s4

WARNING

7.When you operate the machine using a machining program created using a conversationalfunction or a machining program generated by converting another machining program to NC

program format, be particularly careful to use the correct tool compensation data.

If the machine is used with incorrect data, the tool may collide with the machine and/or

workpiece, possibly causing damage to the tool and/or machine, or even injury to the user or

bystanders.The method of measuring the tool compensation amount varies depending on the

machine tool builder. Before starting measurement, therefore, users must read and become

totally familiar with the relevant manual(s), supplied by the machine tool builder.

8. After pressing the power ON button, do not touch any key on the keyboard until the screen

display appears. Some keys are allocated to maintenance or other special operations. Pressing

any of these keys may result in the machine not behaving as expected.


7/461

B63294EN/02 Table of contents

c1

SAFETY PRECAUTIONS s1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. WARNING, CAUTION, AND NOTE s2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2. GENERAL WARNINGS AND CAUTIONS s3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

I. OVERVIEW 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. MANUAL OVERVIEW 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2. SYMBOLS 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3. GENERAL PROCEDURE FROM PROGRAMMING TO EXECUTION 5. . . . . . . . .

4. OPERATING PRECAUTIONS 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.1 Input Data 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2 Background Editing 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3 Tool Offset Number 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4 Parameters 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

II. Super CAPi M 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. OVERVIEW OF Super CAPi M 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1 Work Overview 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2 Creating a Machining Program [Basic Menu 1] 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3 Editing a Machining Program [Basic Menu 1] 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3.1 Modify function 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3.2 Insert function 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3.3 Move function 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3.4 Copy function 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3.5 Delete function 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4 Machining Program Optimization [Basic Menu 2] 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4.1 Optimal process editing function (automatic alteration) 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4.2 Optimal process editing algorithm 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4.3 Optimal process editing function (manual alteration) 48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.5 Machining Program Check [Basic Menu 3] 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.5.1 Tool path drawing 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.5.2 Animated simulation 57. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.5.3 Machining time display 62. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.5.4 Background drawing (optional) 63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.5.5 Changing the screen display colors 66. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.5.6 Notes on drawing 68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6 NC Statement Output Function [Basic Menu 4] 69. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6.1 NC statement output function 69. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6.2 Alarms raised during NC statement output 72. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6.3 Settings related to the reader/punch interface 73. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7 Conversational Data Setting and Reference [Basic Menu 8] 74. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7.1 Data I/O 76. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7.2 Initial value file 78. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


8/461

B63294EN/02Table of contents

c2

1.7.3 Tool list 79. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7.4 Pretool list 80. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7.5 Tool file 81. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7.6 Tool directory 83. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.7.7 Categorized tool directories 84. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7.8 Cutting condition file A 85. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7.9 Cutting condition file B 86. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7.10 Offset file 93. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7.11 NC statement conversion comment file 94. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.8 Other Functions 96. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.8.1 Program list 96. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.8.2 Arithmetic functions 100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.8.3 Embedding tool management numbers 101. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2. MACHINING MENU DESCRIPTIONS 102. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1 Types of Machining Menus 102. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2 Auxiliary 104. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.1 Initial setting (ZI01) 106. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.2 End of program (ZI02) 108. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.3 B axis rotation (ZI03) 109. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.4 NC language preparation (ZI04) 110. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.5 All copy (Random) (ZI05) 112. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.6 All copy (Pattern) (ZI06) 114. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.7 Group copy (Random) (ZI07) 116. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.8 Group copy (Pattern) (ZI08) 117. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.9 Group copy (Turn) (ZI09) 119. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.10 All copy mirror (ZI10) 121. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.11 Group copy mirror (ZI11) 123. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3 Hole Machining 125. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3.1 Drilling (ZH01) 126. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3.2 Peck drilling (ZH02) 131. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3.3 Boring (ZH03) 133. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3.4 Fine boring (ZH04) 135. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3.5 Backboring (ZH05) 137. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3.6 Tapping (ZH06) 139. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3.7 Reaming (ZH07) 141. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3.8 Spot facing (Circle cut) (ZH08) 143. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4 Hole Pattern 145. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.1 Group of points (ZL01) 147. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.2 Line (Same space) (ZL02) 148. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.3 Line (Differ SPC) (ZL03) 150. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.4 Grid (ZL04) 151. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.5 Parallelogram (ZL05) 152. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.6 Bolt hole circle (ZL06) 153. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.7 Arc (Same space) (ZL07) 154. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.8 Arc (Differ space) (ZL08) 155. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.9 Copy (Random) (ZL09) 156. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.10 Copy (Pattern) (ZL10) 157. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5 Facing 159. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5.1 Facing prepare (ZF01) 160. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5.2 Square (unidir) (ZF02) 164. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5.3 Square bidir (ZF03) 167. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.5.4 Circle unidir (ZF04) 169. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5.5 Circle bidir (ZF05) 170. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5.6 Square (Ring) (ZF06) 171. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


9/461

B63294EN/02 Table of contents

c3

2.5.7 Circular surface (Ring) (ZF07) 173. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5.8 Copy (Random) (ZF08) 173. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5.9 Copy (Pattern) (ZF09) 173. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.6 Side Cutting 174. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.6.1 Side preparation (ZS01) 176. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.6.2 Square outside (ZS02) 185. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.6.3 Square inside (ZS03) 193. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.6.4 Circle outside cutting (ZS04) 195. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.6.5 Circle inside (ZS05) 196. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.6.6 Track outside (ZS06) 197. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.6.7 Track inside (ZS07) 198. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.6.8 One side (ZS08) 199. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.6.9 Contour prepare (ZS09) 202. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.6.10 Copy (Random) (ZS10) 203. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.6.11 Copy (Pattern) (ZS11) 203. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.7 Pocketing 204. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.7.1 Pocketting prep. (ZP01) 206. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.7.2 Square pocket (ZP02) 212. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.7.3 Circle pocket (ZP03) 215. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.7.4 Track pocket (ZP04) 216. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.7.5 Polygonal pocket (ZP05) 217. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.7.6 Polygonal pokt (with radius) (ZP06) 221. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.7.7 Grooving (ZP07) 222. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.7.8 Cont pocket prep (ZP08) 225. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.7.9 Contour grooving preparation (ZP09) 231. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.7.10 Copy (random) (ZP10) 234. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.7.11 Copy (pattern) (ZP11) 234. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.8 NC Language 235. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.8.1 Positioning (ZN01) 236. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.8.2 Line (ZN02) 237. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.8.3 Arc (ZN03) 238. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.8.4 Program stop/end (ZN04) 239. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.8.5 Feed rate (ZN05) 240. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.8.6 Coolant (ZN06) 241. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.8.7 Spindle (ZN07) 242. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.8.8 NC language (ZN08) 243. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.9 2 + 1/2 Convex Cut 244. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.9.1 2 + 1/2 Convex cut prep. (ZV01) 245. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.9.2 CVX QUAD PR (ZV02) 249. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.9.3 CVX hemisphere (ZV03) 256. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.9.4 CVX half CYL L (ZV04) 258. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.9.5 CVX HLF CYL ring (ZV05) 260. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.9.6 Copy (random) (ZV06) 260. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.9.7 Copy (pattern) (ZV07) 260. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.10 2 + 1/2 Concave Cut 261. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.10.1 2 + 1/2 Concave cut prep. (ZC01) 262. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.10.2 CCV QUAD PR with Corner Rounding (ZC02) 269. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.10.3 CCV hemisphere (ZC03) 274. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.10.4 CCV half CYL L (ZC04) 275. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.10.5 CCV HLF CYL ring (ZC05) 276. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.10.6 Copy (random) (ZC06) 276. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.10.7 Copy (pattern) (ZC07) 276. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.11 Contour Cutting Programming 277. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.11.1 Contour side cutting 277. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.11.2 Contour pocketing A 294. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


10/461

B63294EN/02Table of contents

c4

2.11.3 Contour pocketing B (option) 300. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.11.4 Contour grooving 305. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.11.5 Calculating a contour figure 308. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.11.6 Contour repetition function (option) 326. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.11.7 Contour editing 332. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.11.8 Contour figure window function 333. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.11.9 Contour alarms 335. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.11.10 Restrictions and rules on calculating the contour 337. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.12 Uaxis Machining (Option) 343. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.12.1 Uaxis machining menu items 343. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.12.2 Creating and editing a Uaxis machining program 345. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.12.3 Checking a Uaxis machining program 371. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.12.4 Uaxis machining program NC statement output 373. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.12.5 Tool file for Uaxis machining 376. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.12.6 Restrictions imposed on Uaxis machining 379. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.13 Setup Guidance Function 382. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.13.1 Outline 382. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.13.2 Operation 383. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.13.3 Appendix 397. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.14 Direct Operation of C.A.P. Program 400. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.14.1 General 400. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.14.2 Screen configuration 400. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.14.3 Program restart 406. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

III. PARAMETERS AND ALARMS 413. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. PARAMETERS 415. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1 Parameters Related to Graphic Display 415. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2 Macro Executor 417. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3 CAP Control 418. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4 CAP File 424. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.5 Menu Control 429. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6 Contour 432. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7 Workpiece Material Name 438. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.8 VGA Display 440. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2. ALARMS 441. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.1 Alarms Related to Machining Other than Contouring 441. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2 Alarms Related to Contouring 442. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

IV. GLOSSARY 443. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. GLOSSARY 445. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


11/461

I. OVERVIEW


12/461


13/461

B63294EN/02 1. MANUAL OVERVIEW

3

1. MANUAL OVERVIEWThis manual describes the functions of FANUC Super CAPi M.

For the other functions, refer to the operators manual describing the NC of the FANUC Series 16/18/21.

The specifications and use of FANUC Super CAPi M depend on the specifications of the machine operators

manual. Be sure to refer to the manual written by the machine tool builder.

The functions of a CNC machine tool system are determined not only by the CNC but also by the combination

of the machine, power magnetics circuit, servo system, CNC, operators panel, and other units.

It is impossible to explain the functions, programming, and operations for each of the combinations.

This manual describes the conversational input functions of the CNC. For the functions of each CNC machine

tool, refer to the manual written by the machine tool builder.

FANUC Super CAPi M are compatible with the following models. These model names are abbreviated in this

manual.

Product name Abbreviation

FANUC Series 16iMA 16iMA

FANUC Series 18iMA 18iMAFANUC Series 21iMA 21iMA

FANUC Series 16iMB 16iMB



FANUC Super CAPi M consist of custom macro programs. In addition to standard custom macroinstructions, many conversational macro instructions (for example, a macro instruction for drawing) areprovided.

FANUC separately provides the FANUC standard program, a conversational automatic programmingfunction created from custom macro programs by FANUC. (The FANUC standard program can be pur-chased as a ROM module.) By adding to and modifying the custom macro program of the FANUC stan-

dard program, and each machine tool builder can create his own conversational automatic program-ming function incorporating the machining knowhow.

This manual describes the conversational automatic programming function provided by FANUC. Thespecifications depend on each machine tool builder. Ask the machine tool builder beforehand whetherthey have added to or modified the standard function.

The description in the manual written by the machine tool builder has priority over that in this manual.

This manual gives a lot of information to the reader. It, however, cannot detail all the operations that must not

be attempted or cannot be executed.

The system can execute only functions that are explicitly said to be possible in this manual.

Notes in this manual describe particular conditions in minute detail. The note may include terms which have

not yet been explained. If such terms are found, skip the note and read the remaining part of the manual. Then,

read the note again.


14/461

B63294EN/021. MANUAL OVERVIEW

4

2. SYMBOLS

This manual indicates key operations by using the following symbols:

(1) An MDI key (on which alphanumeric characters or symbols are marked) is enclosed in a pair of angle

brackets ().

Example

(2) A soft key (shown at the bottom of the screen) is enclosed in a pair of square brackets ([]).

Example [C.A.P.] [EXEC]

(3) Cursor keys are represented as follows:

(4) Page keys are represented as follows


15/461


5

3. GENERAL PROCEDURE FROM PROGRAMMING TO EXECUTION

The flowchart below shows a general procedure from programming to machining with the conversational auto-

matic programming function.

Start

Creation and editing of a program by the

conversational automatic programming

function

See Sections 1.1, 1.2, 1.3, and 1.7 of

Chapter II. (EDIT and back ground edit

modes)

Optimization of the machining program See Section 1.4 of Chapter II. (EDIT

and back ground edit modes)

Program check by drawing See Section 1.5 of Chapter II.

(MEMORY mode)

NC program conversion See Section 1.6 of Chapter II.

(MEMORY mode)

Machining (MEMORY mode)

End


16/461

B63294EN/021. MANUAL OVERVIEW

6

Before starting to create a machining program using a conversational function, first check thatall required data within the tool file, cutting condition file, and pretool list, is set correctly.If any of the required data is not set correctly, the cutting conditions will not be set correctly, possi-bly causing damage to the tool, or even injury to the user or bystanders.

Before proceeding to the next step of a procedure, carefully check the contents of the screendisplay to ensure that the data has been entered exactly as intended.If the machine is operated with incorrect data, the tool may collide with the machine and/or work-piece, possibly causing damage to the tool and/or machine, or even injury to the user or bystand-ers.

WARNING

WARNING


17/461


7

4. OPERATING PRECAUTIONS

4.1 Input Data

(1) On the conversational data input screen, enter lengths and coordinates in millimeters (metric mode) or in-

ches (inch mode).

(2) Usually, entries with an asterisk (*) need not be specified in the FANUC standard macro. Specify them only

when required.

Data cannot be set in entries marked withJ. Those entries are set automatically according to the settings

of options and parameters.

(3) This system is not applicable to machines operating in ISC (0.1 um) mode.

(4) This system is not applicable to sets 48 and 300 of the workpiece coordinate system.

4.2 Background Editing

The following operations cannot be executed during background editing:(1) Drawing of the machining profile, animated simulation

(Can be executed if the optional background drawing function is provided.)

(2) NC statement output function

(3) Setting and changing the tool offset value in the list of tools to be used

(4) Setting and changing a tool file

4.3 Tool Offset Number

When contour side cutting or contour pocket cutting is carried out, the offset data in parameter No. 9404 is auto-

matically overwritten. The offset number and offset data cannot be used.

When 0 is set in that parameter, the following offset data is used instead.(1) Data No. 32 when 32 sets of tool offset are specified

(2) Data No. 64 when 64 sets of tool offset are specified



4.4 Parameters

Be sure to set the following parameter bits to 0.

(1) SGD (bit 0) of parameter No. 3112 = 0 (servo waveform display)

(2) LVK (bit 6) of parameter No. 5003 = 0 (cancellation of tool length compensation)

(3) OIM (bit 0) of parameter No. 5006 = 0 (switching of tool compensation between inch and metric modes)


18/461


19/461

II. Super CAPi M


20/461


21/461

B63294EN/02 1. OVERVIEW OF Super CAPi M

11

1. OVERVIEW OF Super CAPi M

1.1 Work Overview

Conversational automatic programming is a technique for creating machining programs by entering the dimen-

sions of drawings and other data on the CRT screen.

To use the conversational automatic programming function, press the key on the MDI panel, then

press the soft key [C.A.P.]. (The [C.A.P.] key is displayed on the screen only when the NC unit is in the EDIT

or BGEDIT mode.)

The menu screen shown below (basic menu screen) is displayed. Conversational programming begins with

the basic menu screen.

In general conversational programming, select menus 1 to 4 in that order. Menu 8 is used to reference or set

a conversational file or to input or output data from or to external equipment. Select menu 8 only when required.Before using the following menu, set the NC unit in the corresponding mode:

[1] Creating and editing a machining program : EDIT or BGEDIT mode

[2] Optimizing a machining program : EDIT or BGEDIT mode

[3] Checking a machining program : AUTO mode

[4] NC program conversion : AUTO mode

[8] Conversational data : The mode of the NC unit does not matter.

The following sections describe each menu with examples.


22/461

B63294EN/021. OVERVIEW OF Super CAPi M

12

1.2 Creating a Machining Program [Basic Menu 1]

A machining program is created by the following procedure:

Start

Program creation screen

Automatic

Initial setting Enter the initial data (workpiece material, coolant,

reference coordinate system) required for machining.

Selection of a machining menu

Select a desired machining menu.

Specification of the machining data In response to messages displayed on the screen,

(1) Specify a machining method. Position on the

Zaxis, tool (preparation menu)

(2) Specify the figure data. Positions on the Xand

Yaxes (figure menu)

(3) Specify the process end.

Repeat these steps until all machining data is speci

fied.

Automatic

Program end

Select [PROGRM END].

End

> INPUT PROGRAM NO.

4321

PROG.

SELECT

NC

LAN-

GUAGE

POCKET

/GROOV

SIDE

CUTING

FACINGHOLE

PROGRM

END

AUX-

ILIARY

2+1/2

CCV

2+1/2

CVX

PROGRM

END

AUX-

ILIARY

2+1/2

CCV

2+1/2

CVX

Title input Enter a program name.


23/461


13

First, the operator selects a machining menu, then enters the type of machining, figure of product, and other

data in response to inquiries on the screen. The operator repeats this process to generate a machining pro-

gram.

*1 The machining data is specified in the following procedures. The menu of (1) below is automatically dis-

played only once immediately after the machining menu is selected.

Preparation menu

(1) (2)

Figure menu

(3)

Process end

Drilling Hole position

This step can be repeated.

Facing start menu Corresponding facing menu

Side cutting start menu Corresponding side cutting menu

Contouring start menu Corresponding contouring menu

Pocketing start menu Corresponding pocket cutting menu

Contour pocket /

grooving start menu

NC language

Corresponding contouring menu

2 +1/2 start Corresponding 2 +1/2 menu

Auxiliary

Contour end

Process end

.

.

.

.

.

.

.

.

.





Process end

Contour end

Process end

Process end

Process end

A single machining process has the machining data of the [START MENU], [FIGURE MENU], and [PRO-CES END]. The system checks whether the machining data consists of the above three elements and

prevents the operator from creating a machining program which cannot be executed.


24/461

B63294EN/021. OVERVIEW OF Super CAPi M

14

*2 The screen on which the machining data is specified is basically configured as shown below. The A, B,

and C windows show different data.

A B

C

Ten soft keys

Return key Next key

A : Program screen that is always displayed. The data in the B and C windows depend on the data

input. The A window always lists the existing programs.

B : Guide screen that displays the data of the C window with a drawing or tool file. The cursor is placed

on the corresponding parameter in the C window.

C : Data input screen. Basically, the data (parameter) is displayed and specified in this window. The

data which cannot be displayed in this window (data to be determined automatically,cuting condi-

tions, etc.) is displayed and specified in the B window.

Return key: Displays the previous screen. When the return key can be used,

[


25/461


15

Examples are given below:

The machining programs presented in the following examples differ from those used for actualmachining. Actual data will vary from one machine model to another. Refer to the relevantmanual(s), supplied by the machine tool builder, for details.If the set data is incompatible with the characteristics of a specific machine, a machining program

created using the conversational function will not be able to operate as intended.If a machining program fails to operate correctly, the tool may collide with the workpiece, or themachine may be forced to perform machining that exceeds its physical capabilities, possiblycausing damage to the tool and/or machine, or even injury to the user or bystanders.

1. Select [1] on the basic menu screen. The following program list screen is displayed:

(For details of the program list, see Subsec. 1.8.1.)

INPUT PROGRAM NO. >_

PROG.SELECT

LI-BRARY

MODIFYTITLE

PROG.DELETE

PROG.COPY

PROGRAM DIR. PAGE 01/01 EDIT

PROGRAM NO. USED: 7 FREE: 99MEMORY AREA USED: 560 FREE: 3704

NO. TYPE NAME CREATE DATA SIZE0001 CAP TEST1 DEMO 941006 11:47 800002 CAP TEST2 SUS304 941006 11:49 80

0003 CAP TEST3 FCD45 941006 11:50 800004 CAP TEST4 SKD11 941006 11:51 800005 CAP TEST5 SUS41 941006 11:52 800006 CAP TEST6 ALUME 941006 11:53 800007 CAP TEST7 SPECIAL 941006 11:56 80

fanuc super cap i m operator

Documents