fb - 2 - 003 upstand detail under vertical cladding...bs en 12691-a ≥1000 ≥1000 resistance to...
TRANSCRIPT
Polyglass GB Ltd, Unit 1, Electrium Point, Ashmore Lake Way, Willenhall, West Midlands, WV12 4HD. T: 01902 637422 F: 01902 637459
© Polyglass GB Ltd - 2015
1. Deck2. Wall3. Vapour check or barrier4. Insulation fully bonded type5. Underlay6. PUR angle fillet 7. Cap sheet8. Detail cap sheet in 25mm chase9. Cladding
FB - 2 - 003 Upstand detail under vertical cladding
2 8 9
31 4 6 75
Polyglass GB Ltd, Unit 1, Electrium Point, Ashmore Lake Way, Willenhall, West Midlands, WV12 4HD. T: 01902 637422 F: 01902 637459
© Polyglass GB Ltd 2015
7 5
2 361 4
1. Deck2. Vapour check or barrier3. Insulation fully bonded type4. Underlay5. Cap sheet6. Treated timber fillet7. Rainwater outlet
FB - 2 - 017 Existing rainwater outlet detail
Polyglass GB Ltd, Unit 1, Electrium Point, Ashmore Lake Way, Willenhall, West Midlands, WV12 4HD. T: 01902 637422 F: 01902 637459
© Polyglass GB Ltd 2015
78 6 5
2 39 1 4
1. Deck2. Vapour check or barrier3. Insulation fully bonded type4. Underlay5. Cap sheet6. Detail cap sheet7. Aluminium flashing8. Rooflight9. Rooflight upstand
FB - 2 - 023 Rooflight detail
Product Data Sheet
High Performance Elastomeric Membrane Cap Sheet March 2018
Description
Roof Flex Pro S6 Mineral Cap Sheet is a range of polyester based
elastomeric roofing membranes, coated with a high quality polymer
modified SBS bitumen coating. Roof Flex Pro S6 is available in two
versions, one for installation by the traditional pour & roll method and
one by torch-on application. The underside of the torch-on version is
protected by Polyflam a special polyethylene film which melts upon
torching and the pour & roll version is finished with a fine sand surface.
In both versions the top surface is protected by a uniform layer of slate
chippings and has a lateral selvedge for overlapping making
application fast and secure. Roof Flex Pro S6 membranes provide
reliable and effective flat roof waterproofing, combining the qualities of
excellent performance, good handling characteristics and economy.
Roof Flex Pro S6 membranes exhibit excellent dimensional and
mechanical stability making them suitable as part of a built-up system,
or as a refurbishment overlay to existing asphalt or selected compatible
surfaced membranes. Features and Benefits:-
• Available in both torch-on and pour & roll applications • Strong rot resistant polyester base • Flexible SBS elastomeric modified bitumen • Low temperature flexibility -20°C • Cost effective performance • 20 year System Warranty available
Dimensions & Weights Roof Flex Pro S6 Mineral Pour & Roll Roof Flex Pro S6 Mineral Torch-On
Roll Weight kg 40 40 Weight kg/m2 4 5 Roll Length m 10 8 Roll Width m 1 1 Thickness mm N.A. N.A. Selvedge Width mm 75 75 Product Components
Base Polyester Polyester Typical Performance
Tensile Strength (MD) Nf50mm 800 800 Tensile Strength (TD) Nf50mm 600 600 BS EN 12311-1
Elongation (MD) % 50 50 Elongation (TD) % 50 50 BS EN 12311: 2000
Resistance to Impact mm
BS EN 12691-A ≥1000 ≥1000 Resistance to Static Loading kg
BS EN 12730 -A ≥15 ≥15 Low Temperature Flex °C -20 -20
BSEN 1109: 2000
Roof Flex Pro S6
Polyester Mineral
Product Information The pour & roll version of Roof Flex Pro S6 mineral
slate surfaced cap sheet incorporates a non-woven
polyester base, coated with SBS modified bitumen,
providing a very high degree of strength and
durability. Available with a grey, black or tweed
slate finish and surfaced on the underside with fine
sand. For exposed use and requiring no further
finishing on site, however, additional surface
protection may be necessary on trafficked areas.
Please consult the Polyglass technical department. The torch-on version of Roof Flex Pro S6 mineral
slate surfaced cap sheet incorporates a non-woven
polyester base, coated with SBS modified bitumen,
providing a very high degree of strength and
durability. Available with a grey or black slate finish
and surfaced on the underside with flame
dispersible polyethylene film (Polyflam). For
exposed use and requiring no further finishing on
site, however, additional surface protection may be
necessary on trafficked areas. Please consult the
Polyglass technical department. Application Roof Flex Pro S6 can be used as the cap sheet
onto suitable pour and roll or torch-on underlays
as part of a built-up system or as a
refurbishment overlay to existing asphalt or
selected compatible surfaced membranes.
Roof Flex Pro S6 roofing membranes should be
installed in accordance with BS 8217: 2005 Code
of Practice for reinforced bitumen membranes for
roofing and to Polyglass specifications and
recommendations. The application should follow
the general good practice for roofing membranes.
Care must be taken when applying the Roof Flex
Pro S6 torch-on version in close proximity to
combustible materials, decorative coatings and
heat sensitive materials. Apply the torch-on version of Roof Flex Pro S6 by
melting the heat dispersible backing and coating to
create a molten flow in front of the roll. The flame
of the torch should be applied at the low point
where the roll meets the underlay, rolling the
membrane forward as the film and bitumen melts.
Side joints in the sheets should be fully bonded
and formed using the selvedge. NB. A bead of
bitumen must exude from all lap joints to ensure a
seal. In the pour & roll version, hot bitumen is
poured in front of the membrane which is then
unrolled into the bitumen, spreading it to give a
continuous coating for the full width of the roll.
Excess bitumen at the laps may be removed to
maintain the appearance. To facilitate this, the
preceding layer of mineral roofing is ‘wetted’ to
prevent adhesion of the excess. Other Products Full product literature, health & safety and
technical sheets are available as downloads or
on request from our Head Office, detailed below.
Roof Flex Pro Roofing Systems are only available to Approved Installers.
www.polyglass.com
Polyglass GB Ltd
Head Office & Sales Office 1 Electrium Point, Ashmore Lake Way,Willenhall.West Midlands WV12 4LF
Tel: 01902 637422 Fax: 01902 637459 E-Mail: [email protected]
Whilst every care is taken to see that the information given in this literature is correct and up to date it is not intended to form part of any
contract or give rise to any collateral liability, which is hereby specifically excluded. Intending purchasers of our materials should therefore verify
with the company whether any changes in our specification or application details or otherwise have taken place since this literature was issued.
Company Registration No. SC182195 - Registered Office: 7 Tollpark Road, Wardpark East, Cumbernauld, North Lanarkshire, G68 0LW
Product Data Sheet
High Performance Elastomeric Polyester Underlay February 2018
Description Roof Flex Pro S6 Underlay is a range of polyester based underlays,
coated with a high quality polymer modified SBS bitumen coating. The
underside of Roof Flex Pro S6 Underlay is protected by Polyflam a
special polyethylene film which melts upon torching.
Roof Flex Pro S6 TT Underlay is protected by Polyflam on both the top
and underside thus providing a bitumen rich surface when torching
applying the Flexo S6 cap sheet.
The upper face of Roof Flex Pro S6 TS Underlay is finished with fine
sand allowing the use of suitably approved adhesives to bond
insulation, etc. to the surface.
Roof Flex Pro S6 torch-on membranes provide reliable and effective flat
roof waterproofing, combining the qualities of excellent performance,
good handling characteristics and economy. Roof Flex Pro S6
membranes exhibit excellent dimensional and mechanical stability
making them suitable as part of a built-up system, or as a refurbishment
overlay to existing asphalt or selected compatible surfaced membranes.
Features and Benefits:- • Torch-on application • Strong rot resistant polyester base • Flexible SBS elastomeric modified bitumen • Low temperature flexibility -20 °C • Cost effective performance
Dimensions & Weights R F P S6 TT 3mm R F P S6 TS 4mm R F P S6 TS 3Kg
Roll Weight kg 32 36 20
Weight kg/m2 N.A. 2 3 Roll Length m 8 8 10 Roll Width m 1 1 1 Thickness mm. 3 4 N.A. Selvedge Width mm N.A. N.A. N.A. Product Components
Base Polyester Polyester Polyester
Typical Performance
Tensile Strength (MD) Nf50mm 500 500 500
Tensile Strength (TD) Nf50mm 400 400 400
BSEN 12311: 2000
Elongation (MD) % 35 35 35
Elongation (TD) % 35 35 35
BSEN 12311: 2000
Low Temperature Flex °C -20 -20 -20
BSEN 1109: 2000
Roof Flex Pro S6
Polyester Underlay
Product Information
Roof Flex Pro S6 Polyester Underlay Sand
Surfaced Finish - Incorporates a non-woven
polyester base, coated with SBS modified
bitumen, providing a very high degree of
strength and durability can be used as a
high performance underlay or as a capsheet
where the surface will be protected by
walkway tiles, chippings or other approved
surface protection.
Application Roof Flex Pro S6 torch-on roofing
membranes should be installed in
accordance with 8217: 2005, Code of
Practice for reinforced bitumen membranes
for roofing, and to Polyglass specifications
and recommendations. The application
should follow the general good practices for
torch-applied membranes. Care must be
taken when applying Flexo S6 torch-on
membranes in close proximity to
combustible materials, decorative coatings
and heat sensitive materials.
Apply roof Flex Pro S6 torch-on roofing by
melting the heat dispersible backing and
coating to create a molten flow in front of the
roll. The flame of the torch should be applied at
the low point where the roll meets the underlay.
As the film and bitumen melts, roll the roofing
forward. Side joints in the sheets should be
fully bonded and formed using the 75mm
selvedge. NB. A bead of bitumen must exude
from all lap joints to ensure a seal. Other Products Full product literature, health & safety and
technical sheets are available as downloads or
on request from our Head Office, detailed
below.
Roof Flex Pro Roofing Systems are only available to Approved Installers
Polyglass GB Ltd
Head Office & Sales Office 1 Electrium Point, Ashmore Lake Way,Willenhall.West Midlands WV12 4LF
Tel: 01902 637422 Fax: 01902 637459 E-Mail: [email protected]
Whilst every care is taken to see that the information given in this literature is correct and up to date it is not intended to form part of any
contract or give rise to any collateral liability, which is hereby specifically excluded. Intending purchasers of our materials should therefore verify
with the company whether any changes in our specification or application details or otherwise have taken place since this literature was issued.
Company Registration No. SC182195 - Registered Office: 7 Tollpark Road, Wardpark East, Cumbernauld, North Lanarkshire, G68 0LW
Product Data Sheet
High Performance Vapour Control Layers February 2018
Description Roof Flex Pro VC is a range of high performance, aluminium cored
vapour control layers (VCL’s) coated with a high quality polymer
modified bitumen coating. The underside of Roof Flex Pro TT & Roof
Flex Pro TS are protected by Polyflam a special polyethylene film
which melts upon torching. In the Roof Flex Pro TT version the top
surface is also protected by a layer of Polyflam providing a bitumen rich
surface. The top surface of Roof Flex Pro TS has a coating of fine sand
thereby enabling the use of bitumen or Roof Flex Pro polyurethane
adhesive to bond insulation to the upper face of the VCL. Roof Flex Pro
SA is a self-adhesive membrane manufactured using ADESO ®
technology and can be incorporated into a completely flame free self-
adhesive roofing system.
Features and Benefits:-
• Torch-on and Self-Adhesive applications available
• Aluminium core stops ingress of water vapour and damage to
roof construction.
• Durable polymer modified bitumen coating.
• Cost effective performance.
• Part of a complete package of waterproofing components.
Dimensions & Weights Roof Flex Pro TT Roof Flex Pro TS Roof Flex Pro SA
Roll Thickness kg 3mm 3mm 2mm
Roll Length m 8m 10m 15m
Roll Width m 1m 1m 1m
Product Components
Base Glassfibre/Aluminium Glassfibre/Aluminium Glassfibre/Aluminium
Typical Performance Water Vapour Properties μ
BSEN 1931 1000000 (±30%) 1000000 (±30%) 700000 (±30%)
Tensile Strength (MD) Nf50mm 500 500 500
Tensile Strength (TD) Nf50mm 200 200 200
BSEN 12311: 2000
Elongation (MD) % 30 30 4
Elongation (TD) % 30 30 4
BSEN 12311: 2000
Low Temperature Flex °C -10 -10 -25
BSEN 1109: 2000
Roof Flex Pro
Vapour Control
Product Information Roof Flex Pro Vapour Control layers are high
performance membranes, incorporating an aluminium
core, reinforced with glass fibre and coated with an
advanced, modified bitumen compound, providing a
durable and reliable vapour control layer in areas of high
humidity in warm roof applications. Roof Flex Pro TT has
an upper and lower face finished with Polyflam, a special
polyethylene film which melts upon torching. Roof Flex
Pro TS has an upper face finished with a fine sand and a
lower face finished with Polyflam, a special polyethylene
film which melts upon torching.
Roof Flex Pro SA is a high quality self-adhesive
bituminous vapour control membrane made with
ADESO® technology, the unique self-adhesive compound
system from Polyglass SpA. Roof Flex Pro SA is made
from a special elastomeric (SBS) self-adhesive compound
reinforced with an aluminium foil. This reinforcement
allows the product excellent dimensional stability, good
mechanical characteristics, a complete vapour barrier and
excellent on-site capability. Roof Flex Pro SA has an
upper face finished with a fine sand and the lower face is
protected by a mono-silicone coated polyethylene film
which is removed when the membrane is applied.
Application Roof Flex Pro membranes are designed to be used as
vapour control layers in warm roof construction and as
part of a built-up system in new or refurbishment work. Roof Flex Pro roofing membranes should be
installed in accordance with 8217: 2005, Code of
Practice for Reinforced Bitumen Membranes for
Roofing, and to Polyglass specifications and
recommendations. The application should follow the
general good practices for bituminous membranes.
Care must be taken when applying Roof Flex Pro
torch-on membranes in close proximity to
combustible materials, decorative coatings and heat
sensitive materials.
Apply Roof Flex Pro torch-on roofing by melting the heat
dispersible backing and coating to create a molten flow in
front of the roll. The flame of the torch should be applied at
the low point where the roll meets the underlay. As the film
and bitumen melts, roll the roofing forward. Side joints in
the sheets should be fully bonded and formed using the
75mm selvedge. NB. A bead of bitumen must exude from
all lap joints to ensure a seal. The surface to which Roof
Flex Pro membranes are to be applied should be smooth,
clean and dry and should be primed with a coating of
Polyprimer HP 45. The surface to which Roof Flex Pro SA is to be applied
should be smooth, clean and dry and should be primed with
a coating of Polyprimer HP 45. Roof Flex Pro SA should be
unrolled ensuring that the alignment is correct. Remove half
of the mono-silicone coated release film at the lower end of
the roll, fasten the sheet, and then remove the other half of
the film, taking care to avoid the formation of air bubbles or
wrinkles. When laying on a pitched roof, apply the rolls from
the top downwards. At the roof’s ridge line, the membrane
must be folded back 20-30 cm and then fastened
mechanically. Whenever roof pitch is greater than 30%, the
membrane must be fastened mechanically also at the
overlap points (in accordance with BS standards), in order
to avoid slipping. Make sure that any fixings are completely
covered by the next layer’s selvedge strip. Extra attention
must be paid to the overlapping of the sheets. We
recommend using shears, tile cutters, pressing rollers and
leister hot air guns. The product must never be laid at
temperatures of less than 5°C and always only in good
weather. Roof Flex Pro SA must never be left exposed to
inclement weather.
Other Products
Full product literature, health & safety and technical
sheets are available as downloads or on request from
our Head Office, detailed below.
www.polyglass.com
Polyglass GB Ltd
Head Office & Sales Office 1 Electrium Point, Ashmore Lake Way,Willenhall.West Midlands WV12 4LF
Tel: 01902 637422 Fax: 01902 637459 E-Mail: [email protected]
Whilst every care is taken to see that the information given in this literature is correct and up to date it is not intended to form part of any
contract or give rise to any collateral liability, which is hereby specifically excluded. Intending purchasers of our materials should therefore verify
with the company whether any changes in our specification or application details or otherwise have taken place since this literature was issued.
Company Registration No. SC182195 - Registered Office: 7 Tollpark Road, Wardpark East, Cumbernauld, North Lanarkshire, G68 0LW