8/7/2019 FBH1109 Hood Hinge Installation Instructions

1/2

1. Although our hinges are marketed as an easy install, Fesler Billet strongly

recommends that you have these hood hinges installed by a professional to

avoid the possibility of damaging your vehicle.

2. Fesler Billet is not responsible for customer applications that are outside the

normal and intended use of our products, including specific model and year

applications.

3. Fesler Billet designs hood hinges off original OEM applications. Due to the vast

array of manufacturers for aftermarket parts, it is possible that you may have to

open up your bolt holes in the sheet metal to accommodate the new hinge

application.

4. Due to the vast array of manufacturers for aftermarket parts, and the fact that

you are dealing with a vehicle that is well over 40 years old and has more than

likely seen several owners, you must assume that your original hood is no

longer original. Things like braces, paint and bondo significantly add to the

weight of any hood, therefore drastically affecting the strength of our hood

supports.

5. A common problem occurs with hinge installation when the mounting surface on

the inner fender is bent or out of alignment (pulled out or pushed in at one or

both mounting holes). If this is the case, the mounting holes will not line up

correctly with the hinge. To correct this, double check your inner fender mounting

positions by holding a straight edge against the two mounting holes on the inner

fender. If there is a gap between the straight edge and the sheet metal, the

mounting surface is bent or out of alignment.

6. *Some applications are not designed to work with your factory inner fenders.

Please check to see if your vehicle falls under this category before installing

hinges. Fesler Built is not responsible for damage to inner fenders on these

applications.

7. Depending on your hood manufacturer, you may need a shorter bolt when

attaching the hinge to the hood. Check length before tightening making sure to

look for dimpling.

8. DO NOT UNDER ANY CIRCUMSTANCES DISASSEMBLE THESE HINGES.

Doing so will void your warranty. You may not return hinges that have been

disassembled for any reason. We will be able to tell if you have disassembled

hinges upon their return and you will not be granted a refund if this is so.

QUESTIONS OR COMMENTS?

Call us at 1-866-583-9787

INSTALLATIONINSTRUCTIONS

FBH-1109

1967 1970 Ford Mustang

8/7/2019 FBH1109 Hood Hinge Installation Instructions

2/2

INSTALLATION INSTRUCTIONS

1967 1970 Ford MustangCopyright 2011 by Fesler Productions, LLC. All rights reserved.

1. Remove Hood

2. Remove the factory hinge from the fender

3. Inspect factory bolt holes in fender and test thread with new bolts.

a. Note: If existing bolt holes have damaged threads or rust,

you may have to re-tap them.

4. BEFORE installing your hinges on your vehicle, first install the

stainless steel gas spring to each hinge. IT IS IMPORTANT THATYOU INSTALL THE STRUT WITH THE SHAFT FACING THE REAR

OF THE CAR IN ORDER TO ENSURE PROPER OPERATION AND

PREVENT FAILURE.

5. Position each hinge on the corresponding fender and attach

using the supplied 5/16x1 socket head bolts, each with one

washer. Tighten bolts snug so they are securely attached to

fender. Note: 1 bolt will go in lower rear mounting hole.

6. Attach the hood to the hinges using the supplied 5/16 x 3/4

button head bolts, each with one washer.

a. Note: Be sure to use anti-seize on all bolts before

installing

7. To avoid hitting your cowl when closing the hood for the first time,

slide the hood as far forward as possible before closing. Close

hood carefully making sure it does not hit the fenders or cowl.

8. Check the height and position and make any adjustments by

repositioning the hinge slightly at the hood or fender locations.

PLEASE NOTE: IT IS NOT NECESSARY TO DRILL OUT

MOUNTING HOLES TO ACHIEVE MORE ADJUSTMENT.

DOING THIS WILL VOID ALL WARRANTIES NOT TO

MENTION BEING DANGEROUS.

9. Once hood position has been set, tighten all bolts, remove tape

and go.

10. Be sure to check and tighten ALL BOLTS (including assembly

bolts if necessary) every few months to avoid loosening, which is

often caused by normal use.

____________________________________________________________________

Important Technical Information:

Fesler Billet makes every effort to ensure that you are provided with the most accurate

and up-to-date technical information. However, all technical information is approximate

and may vary upon application. Fesler Billet is not responsible for any consequences

resulting from manufactures technical mid-year changes. Fesler Billet products should

only be installed by a qualified, licensed auto mechanic experienced in the installation of

such products.

Important Anodizing Information:

Anodizing does not produce "flawless" color or finish on any Fesler part ordered thatway. In fact, you should expect to encounter minor variations (or what some call

"blemishes") in the color and finish in individual pieces. Every Fesler finish is unique in

this regard. Remember, these variations are normal, and do not affect the performance

of the part in any way.

Other Important Stuff You Should Probably Read:

Fesler Billet is not responsible for customer applications that are outside the normal

and intended use of our products, including specific model and year applications.

Fesler Billet designs all parts off original OEM applications. Due to the vast array of

manufacturers for aftermarket parts, it is possible that you may have to make some

minor adjustments to either our part or your sheet metal in order for the part to fit

properly

ADJUSTMENTS

Height = Fender Adjustment

Front to Back = Hood Adjustment

Left to Right = Hood Adjustment

If your hood pops up at the cowl, you need to RAISE

the front of the hinge, NOT lower the entire hinge!