figure 1. stm32f429 discovery board€¦ · 13/08/2013 · docid025175 rev 1 7/35 um1670 hardware...

September 2013 DocID025175 Rev 1 1/35

UM1670User manual

Discovery kit for STM32F429/439 lines

IntroductionThe STM32F429 Discovery kit (32F429IDISCOVERY) helps you to discover the high performance of the STM32F4 series and to develop your applications. It is based on an STM32F429ZIT6 and includes an ST-LINK/V2 embedded debug tool interface, 2.4" TFT LCD, SDRAM 64 Mbits, Gyroscope ST MEMS, LEDs, pushbuttons and a USB OTG micro-B connector.

Figure 1. STM32F429 Discovery board

www.st.com

http://www.st.com

Contents UM1670

2/35 DocID025175 Rev 1

Contents

1 Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 Quick start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42.1 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.2 System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.3 Development toolchain supporting the STM32F429 Discovery kit . . . . . . . 4

2.4 Order code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4 Hardware layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64.1 STM32F429ZIT6 microcontroller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4.2 Embedded ST-LINK/V2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124.2.1 Using ST-LINK/V2 to program/debug the STM32F429ZIT6 on board . . 13

4.2.2 Using ST-LINK/V2 to program/debug an external STM32 application . . 14

4.3 Power supply and power selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.4 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.5 Pushbuttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.6 USB OTG supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4.7 Gyroscope MEMS (ST MEMS L3GD20) . . . . . . . . . . . . . . . . . . . . . . . . . 16

4.8 TFT LCD (Thin-film-transistor liquid-crystal display) . . . . . . . . . . . . . . . . 16

4.9 64-Mbit SDRAM (1Mbit x 16-bit x 4-bank) . . . . . . . . . . . . . . . . . . . . . . . . 16

4.10 JP3 (Idd) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4.11 OSC clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174.11.1 OSC clock supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.11.2 OSC 32 KHz clock supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.12 Solder bridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.13 Extension connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

5 Mechanical drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

6 Electrical schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

DocID025175 Rev 1 3/35

UM1670 Contents

3

7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

DocID025175 Rev 1 1/35

UM1670 List of tables

1

List of tables

Table 1. ON/OFF conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Table 2. Features and benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Table 3. Jumper states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Table 4. Debug connector CN2 (SWD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Table 5. Solder bridges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Table 6. MCU pin description versus board function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Table 7. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

List of figures UM1670

2/35 DocID025175 Rev 1

List of figures

Figure 1. STM32F429 Discovery board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Figure 1. Hardware block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Figure 2. Top layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Figure 3. Bottom layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Figure 4. STM32F429ZIT6 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Figure 5. STM32F429ZIT6 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Figure 6. Typical configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Figure 7. STM32F429 Discovery board connections image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Figure 8. ST-LINK/V2 connections image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Figure 9. STM32F429 Discovery board mechanical drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Figure 10. STM32F429 Discovery board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Figure 11. ST-LINK/V2 (SWD only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Figure 12. USB OTG_FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Figure 13. SDRAM 64 Mbits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Figure 14. STM32F429ZIT6 MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Figure 15. Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Figure 16. LCD 2.4” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

DocID025175 Rev 1 3/35

UM1670 Conventions

34

1 Conventions

Table 1 provides the definition of some conventions used in the present document.

Table 1. ON/OFF conventions

Convention Definition

Jumper JPx ON Jumper fitted

Jumper JPx OFF Jumper not fitted

Solder bridge SBx ON SBx connections closed by solder

Solder bridge SBx OFF SBx connections left open

Quick start UM1670

4/35 DocID025175 Rev 1

2 Quick start

The STM32F429 Discovery is a low-cost and easy-to-use development kit to quickly evaluate and start a development with an STM32F4 series microcontroller.

Before installing and using the product, please accept the Evaluation Product License Agreement from www.st.com/stm32f4-discovery.

For more information on the STM32F429 Discovery board and for demonstration software, visit www.st.com/stm32f4-discovery.

2.1 Getting startedFollow the sequence below to configure the STM32F429 Discovery board and launch the DISCOVER application:1. Ensure that the jumpers JP3 and CN4 are set to "on" (Discovery mode).2. Connect the STM32F429 Discovery board to a PC using a USB cable type A/mini-B

through the USB ST-LINK connector CN1, to power the board. The LEDs LD2 (PWR) and LD1 (COM).

3. The following applications are available on the screen:– Clock/Calendar and Game– Video Player and Image Browser (play videos and view images from the USB

mass storage connected to CN6)– Performance monitor (watch the CPU load and run a graphical benchmark)– System Info

4. The demo software, as well as other software examples that allow you to discover the STM32 F4 series features, are available on www.st.com/stm32f4-discovery.

5. Develop your own applications starting from the examples.

2.2 System requirements• Windows PC (XP, Vista, 7)• USB type A to mini-B cable

2.3 Development toolchain supporting the STM32F429 Discovery kit• Altium: TASKING™ VX-Toolset• Atollic: TrueSTUDIO• IAR: EWARM• Keil™: MDK-ARM

2.4 Order codeTo order the STM32F429 Discovery kit, use the STM32F429I-DISCO order code.

DocID025175 Rev 1 5/35

UM1670 Features

34

3 Features

The STM32F429 Discovery board offers the following features: • STM32F429ZIT6 microcontroller featuring 2 MB of Flash memory, 256 KB of RAM in

an LQFP144 package• On-board ST-LINK/V2 with selection mode switch to use the kit as a standalone ST-

LINK/V2 (with SWD connector for programming and debugging)• Board power supply: through the USB bus or from an external 3 V or 5 V supply voltage• L3GD20, ST MEMS motion sensor, 3-axis digital output gyroscope• TFT LCD (Thin-film-transistor liquid-crystal display) 2.4", 262K colors RGB,

240 x 320 dots• SDRAM 64 Mbits (1 Mbit x 16-bit x 4-bank) including an AUTO REFRESH MODE, and

a power-saving• Six LEDs:

– LD1 (red/green) for USB communication– LD2 (red) for 3.3 V power-on– Two user LEDs:

LD3 (green), LD4 (red)– Two USB OTG LEDs:

LD5 (green) VBUS and LD6 (red) OC (over-current)• Two pushbuttons (user and reset)• USB OTG with micro-AB connector• Extension header for LQFP144 I/Os for a quick connection to the prototyping board

and an easy probing

Hardware layout UM1670

6/35 DocID025175 Rev 1

4 Hardware layout

The STM32F429 Discovery board has been designed around the STM32F429ZIT6 microcontroller in a 144-pin LQFP package.

Figure 1 illustrates the connections between the STM32F429ZIT6 and its peripherals (ST-LINK/V2, pushbutton, LED, USB OTG, Gyroscope ST MEMS, Accelerometer + Magnetometer ST MEMS, and connectors).

Figure 2 and Figure 3 help you to locate these features on the STM32F429 Discovery board.

Figure 1. Hardware block diagram

MS32376V1

EmbeddedST-LINK/V2

STM32F429ZIT6

I/O I/O

I/O RESET

LEDsLD3...LD6

SDRAM 64 Mbits

B2 RESET

B1USER

L3GD20

Micro-USB

Mini-USB

SWD

Head

er

Head

er

2.4" QVGATFT LCD

ACP/RF

DocID025175 Rev 1 7/35

UM1670 Hardware layout

34

Figure 2. Top layout

.

MS32363V1

ST-LINK/V2ST-LINK/V2

LD1 (red/green LED)COM

CN2SWD connector

LD2 (red LED)PWR

CN4ST-LINK/DISCOVERY selector

LD3 (orange LED) B2 reset button

LD4 (green LED)

B1 user button

JP3IDD measurement

SB1 (B2-RESET)

3 V power supply input/output

2.4" TFT LCD


8/35 DocID025175 Rev 1

Figure 3. Bottom layout

MS32364V1

SB4, SB6, SB8, SB14 (DEFAULT)

SB10 (STM_RST)

SB3, SB5, SB7, SB13 (RESERVED)

SB18 (MCO)

SB19, 20 (X3 crystal)

SDRAM

SB21 (BOOT1)

SB22, 23, 24, 25

SB26, 27 (USB OTG)

SB11 (RX, TX)SB12 (NRST)

SB9 (SWO)

SB15 (RX, TX)

SB16, 17 (X2 crystal)

USB OTG micro-AB

STM32F429ZIT6

DocID025175 Rev 1 9/35


34

4.1 STM32F429ZIT6 microcontroller This ARM Cortex-M4 32-bit MCU with FPU has 225 DMIPS, up to 2 MB Flash/256 + 4 KB RAM, USB OTG HS/FS, Ethernet, 17 TIMs, 3 ADCs, 20 comm. interfaces, a camera and an LCD-TFT, 1.7-3.6 V operation.

Figure 4. STM32F429ZIT6 package

This device provides the following benefits (see Table 2).

MS32377V1

STM32F429ZIT6

2 Mbytes of Flash memory256 Kbytes of RAM

LQFP144 20 x 20 mm

Table 2. Features and benefits

Features Benefits

High performance– Up to 180 MHz/225 DMIPS Cortex-M4 with single

cycle DSP MAC and floating point unit– CoreMark score: 608 at 180 MHz– CoreMark/MHz: 3.37

– Boosted execution of control algorithms– More features for your applications– Ease of use– Better code efficiency– Faster time to market– Elimination of scaling and saturation– Easier support for meta-language tools

Maximum integration– Up to 2 Mbytes of on-chip dual bank Flash memory, up

to 256 Kbytes of SRAM, reset circuit, internal RCs, PLLs, ultra-small packages (WLCSP)

– Read while write operations support– More features in space-constrained applications– Use of high-level languages: Java, .Net

Designed for high performance and ultra-fast data transfers– ART Accelerator™: memory accelerator– Chrom-ART Accelerator™: graphic accelerator

(rectangle filling, rectangle copy with pixel format conversion and blending)

– Performance equivalent to zero-wait execution from Flash

– Graphic content is created twice as fast and independently from the CPU

– 32-bit, 7-layer AHB bus matrix with up to 10 masters and 8 slaves including 3 blocks of SRAM

– Multi DMA controllers: 2 general-purpose, 1 for USB HS, one for Ethernet

Concurrent execution and data transfer

– One 4th SRAM block dedicated to the core Simplified resource allocation

– Flexible memory interface with SDRAM support: up to 90 MHz, 32-bit parallel

– High bandwidth for external memories– Cost-effective external RAM


10/35 DocID025175 Rev 1

Outstanding power efficiency– Ultra-low dynamic power in Run mode: 260 µA/MHz at

180 MHz running CoreMark benchmark from Flash memory (peripherals off)

– RTC

DocID025175 Rev 1 11/35


34

Figure 5. STM32F429ZIT6 block diagram

GPIO PORT A

AHB/APB2

EXT IT. WKUP 168 AF

PA[15:0]

TIM1 / PWM4 compl. chan. (TIM1_CH1[1:4]N),

4 chan. (TIM1_CH1[1:4]ETR,BKIN as AF

USART1RX, TX, CK,

CTS, RTS as AF

SPI1MOSI, MISO,SCK, NSS as AF

APB

2 60

MH

z

APB

1 30

MH

z

8 analog inputs commonto the 3 ADCs

VDDREF_ADC

UART4

MOSI/SD, MISO/SD_ext, SCK/CKNSS/WS, MCK as AF

SP3/I2S3

TX, RXbxCAN2

DAC1_OUTas AF

ITF

WWDG

4 KB BKPSRAM

RTC_AF1

OSC32_INOSC32_OUT

VDDA, VSSANRST

smcardirDA

16b

SDIO / MMCD[7:0]

CMD, CK as AF

VBAT = 1.65 to 3.6 V

DMA2

SCL, SDA, SMBA as AFI2C3/SMBUS

JTAG & SW

ARM Cortex-M4 180 MHz

NVICETMMPU

TRACECLKTRACED[3:0]

Ethernet MAC10/100

DMA/FIFO

MII or RMII as AFMDIO as AF

USBOTG HS

DP, DMULPI:CK, D[7:0], DIR, STP, NXT

ID, VBUS, SOF

DMA2

8 StreamsFIFO

AR

T A

CC

EL/

CA

CH

E

SRAM 112 KB

CLK, NE [3:0], A[23:0],D[31:0], NOEN, NWEN,NBL[3:0], SDCLKE[1:0], SDNE[1:0], SDNWE, NL

NWAIT/NIORD, NREG, CDINTN

RNG

Camerainterface

HSYNC, VSYNCPUIXCLK, D[13:0]

PH

YUSBOTG FS

DPDMID, VBUS, SOFF

IFO

AHB1 180 MHz

PH

Y

FIFO

USART 2MBpsTemperature sensor

ADC1

ADC2

ADC3IFIF

@VDDA

@VDDA

POR/PDRBOR

Supplysupervision

@VDDA

PVD

Int

POR reset

XTAL 32 kHz

MANAGT

RTC

RC HS

FCLK

RC LS

Standbyinterface

IWDG

@VBAT

@VDDA

@VDD

AWU

Reset &clockcontrol

PLL1,2,3

PC

LKx

VDD = 1.8 to 3.6 VVSSVCAP1, VCPA2

Voltageregulator

3.3 to 1.2 V

VDD Power managmt

@VDD

RTC_AF1Backup register

AH

B b

us-m

atrix

8S

7M

AP

B2

90 M

Hz

LS

TIM14

TIM9 2 channels as AF

DAC1

DAC2

1MB Flash

External memory controller (FMC)SRAM, SDRAM, PSRAM,

NOR Flash, PC Card (ATA), NAND Flash

TIM6

TIM7

TIM2

TIM3

TIM4

TIM5

TIM12

D-BUS

MS30420V2

FIFO

FPU

AP

B1

45 M

Hz

(max

)

SRAM 16 KB

CCM data RAM 64 KBAHB3

AHB2 180 MHz

NJTRST, JTDI,JTCK/SWCLK

JTDO/SWD, JTDO

I-BUS

S-BUS

DMA/FIFO

DMA1

8 StreamsFIFO

PB[15:0]

PC[15:0]

PD[15:0]

PE[15:0]

PF[15:0]

PG[15:0]

PH[15:0]

PI[15:0]

GPIO PORT B

GPIO PORT C

GPIO PORT D

GPIO PORT E

GPIO PORT F

GPIO PORT G

GPIO PORT H

GPIO PORT I

TIM8 / PWM16b

16b

TIM10 16b

TIM11 16b

smcardirDA USART6

4 compl. chan.(TIM8_CH1[1:4]N),4 chan. (TIM8_CH1[1:4], ETR,

BKIN as AF

1 channel as AF

1 channel as AF

RX, TX, CK,CTS, RTS as AF

8 analog inputs commonto the ADC1 & 2

8 analog inputs for ADC3

DAC2_OUTas AF

16b

16b

bxCAN1

I2C2/SMBUS

I2C1/SMBUS

SCL, SDA, SMBA as AF

SCL, SDA, SMBA as AF

SP2/I2S2 MOSI/SD, MISO/SD_ext, SCK/CKNSS/WS, MCK as AF

TX, RX

RX, TX as AF

RX, TX as AF

RX, TX as AFCTS, RTS as AF

RX, TX as AFCTS, RTS as AF

1 channel as AF

UART5

USART3

USART2

smcardirDA

smcardirDA

16b

16b

16b

1 channel as AFTIM13

2 channels as AF

32b

16b

16b

32b

4 channels

4 channels, ETR as AF



DMA1

AHB/APB1

LS

OSC_INOSC_OUT

HC

LKx

XTAL OSC4- 16MHz

FIFO

SPI4SCK, NSS as AFSPI5SCK, NSS as AF

MOSI, MISO,

MOSI, MISO,

SPI6SCK, NSS as AFMOSI, MISO,

RX, TX as AFUART7

RX, TX as AFUART8

SRAM 64 KB

1MB Flash

FIFOLCD-TFT

FIFO

PJ[15:0] GPIO PORT J

PK[7:0] GPIO PORT K

SAI1SD, SCK, FS, MCLK as AF FIFO

Dig

ital f

ilter

NRAS, NCAS, NADV

RTC_50HZ

LCD_R[7:0], LCD_G[7:0], LCD_B[7:0],LCD_HSYNC, LCD_VSYNC, LCD_DE,

LCD_CLK

CHROM-ARTDMA2D


12/35 DocID025175 Rev 1

4.2 Embedded ST-LINK/V2The ST-LINK/V2 programming and debugging tool is integrated on the STM32F429 Discovery board. The embedded ST-LINK/V2 can be used in 2 different ways according to the jumper states (see Table 3): • Program/debug the MCU on board, • Program/debug an MCU in an external application board using a cable connected to

SWD connector CN3.

The embedded ST-LINK/V2 supports only SWD for STM32 devices. For information about debugging and programming features, refer to user manual UM1075 (ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32) which describes in detail all the ST-LINK/V2 features.

Figure 6. Typical configuration

Table 3. Jumper states

Jumper state Description

Both CN4 jumpers ON ST-LINK/V2 functions enabled for on-board programming (default)

Both CN4 jumpers OFF ST-LINK/V2 functions enabled for application through externalCN3 connector (SWD supported)

MS31115V1

Hardware requirements:- USB cable type A to mini-B- Computer with Windows XP, Vista or 7

Development toolchains:- Altium TASKING VX-Toolset- Atollic TrueSTUDIO- IAR EWARM- Keil MDK-ARM

DocID025175 Rev 1 13/35


34

4.2.1 Using ST-LINK/V2 to program/debug the STM32F429ZIT6 on board To program the STM32F429ZIT6 on board, simply plug in the two jumpers on CN4, as shown in Figure 7 in red, but do not use the CN3 connector as that could disturb the communication with the STM32F429ZIT6 of the STM32F429 Discovery board.

Figure 7. STM32F429 Discovery board connections image


14/35 DocID025175 Rev 1

4.2.2 Using ST-LINK/V2 to program/debug an external STM32 applicationIt is very easy to use the ST-LINK/V2 to program the STM32 on an external application. Simply remove the two jumpers from CN4 as shown in Figure 8, and connect your application to the CN3 debug connector according to Table 4.

Note: SB7must be OFF if you use CN2 pin 5 in your external application.

Figure 8. ST-LINK/V2 connections image

Table 4. Debug connector CN2 (SWD)

Pin CN2 Designation

1 VDD_TARGET VDD from application

2 SWCLK SWD clock

3 GND Ground

4 SWDIO SWD data input/output

5 NRST RESET of target MCU

6 SWO Reserved

DocID025175 Rev 1 15/35


34

4.3 Power supply and power selectionThe power supply is provided either by the host PC through the USB cable, or by an external 5 V power supply.

The D1 and D2 diodes protect the 5 V and 3 V pins from external power supplies:• 5 V and 3 V can be used as output power supplies when another application board is

connected to pins P1 and P2.In this case, the 5 V and 3 V pins deliver a 5 V or 3 V power supply and the power consumption must be lower than 100 mA.

• 5 V and 3 V can also be used as input power supplies, e.g. when the USB connectors are not connected to the PC.In this case, the STM32F429 Discovery board must be powered by a power supply unit or by an auxiliary equipment complying with standard EN-60950-1: 2006+A11/2009, and must be Safety Extra Low Voltage (SELV) with limited power capability.

Note: The board can also be powered through the USB USER connector and is protected by D4 and D5 diodes when both USBs are connected (in which case, the 5 V power is around 4.4 volts).

4.4 LEDs• LD1 COM:

LD1 default status is red. LD1 turns to green to indicate that communications are in progress between the PC and the ST-LINK/V2.

• LD2 PWR: The red LED indicates that the board is powered.

• User LD3: The green LED is a user LED connected to the I/O PG13 of the STM32F429ZIT6.

• User LD4: The red LED is a user LED connected to the I/O PG14 of the STM32F429ZIT6.

• User LD5: The green LED indicates when VBUS is present on CN6 and is connected to PB13 of the STM32F429ZIT6.

• User LD6: The red LED indicates an overcurrent from VBUS of CN6 and is connected to the I/O PC5 of the STM32F429ZIT6.

4.5 Pushbuttons• B1 USER:

User and Wake-Up button connected to the I/O PA0 of the STM32F429ZIT6.• B2 RESET:

The pushbutton connected to NRST is used to RESET the STM32F429ZIT6.


16/35 DocID025175 Rev 1

4.6 USB OTG supportedThe STM32F429ZIT6 is used to drive only USB OTG full speed on this board. The USB micro-AB connector (CN6) allows the user to connect a host or device component, such as a USB key, mouse, and so on.

Two LEDs are dedicated to this module:• LD5 (green LED) indicates when VBUS is active• LD6 (red LED) indicates an overcurrent from a connected device.

4.7 Gyroscope MEMS (ST MEMS L3GD20)The L3GD20 is an ultra-compact, low-power, three-axis angular rate sensor. It includes a sensing element and an IC interface able to provide the measured angular rate to the external world through the I2C/SPI serial interface.

The L3GD20 has dynamically user-selectable full scales of ± 250 dps/500 dps/±2000 dps and is capable of measuring rates.

The STM32F429ZIT6 MCU controls this motion sensor through the SPI interface.

4.8 TFT LCD (Thin-film-transistor liquid-crystal display)The TFT LCD is a 2.41" display of 262 K colors. Its definition is QVGA (240 x 320 dots) and is directly driven by the STM32F429ZIT6 using the RGB protocol. It includes the ILI9341 LCD controller and can operate with a 2.8 ±0.3 V voltage.

The STM32F429ZIT6 MCU controls this motion sensor through the SPI interface.

4.9 64-Mbit SDRAM (1Mbit x 16-bit x 4-bank)The 64-Mbit SDRAM is a high speed CMOS, dynamic random-access memory designed to operate in 3.3 V memory systems containing 67,108,864 bits. it is internally configured as a quad-bank DRAM with a synchronous interface. Each 16,777,216-bit bank is organized as 4,096 rows by 256 columns by 16 bits. The 64-Mbit SDRAM includes an AUTO REFRESH MODE, and a power-saving, power-down mode. All signals are registered on the positive edge of the clock signal, CLK.

The STM32F429ZIT6 MCU reads and writes data at 80 MHz.

4.10 JP3 (Idd)Jumper JP3, labeled Idd, allows the consumption of STM32F429ZIT6 to be measured by removing the jumper and connecting an ammeter.• Jumper on: STM32F429ZIT6 is powered (default).• Jumper off: an ammeter must be connected to measure the STM32F429ZIT6 current,

(if there is no ammeter, the STM32F429ZIT6 is not powered).

DocID025175 Rev 1 17/35


34

4.11 OSC clock

4.11.1 OSC clock supplyThe following information indicates all configurations for clock supply selection.• MCO from ST-LINK (from MCO of the STM32F429ZIT6)

This frequency cannot be changed, it is fixed at 8 MHz and connected to PH0-OSC_IN of the STM32F429ZIT6. The configuration needed is:– SB18 closed, SB19 open, R56 removed– SB20, R57, C20, C21, X3 = don't care

• Oscillator onboard (from X3 crystal)For typical frequencies and its capacitors and resistors, please refer to the STM32F429ZIT6 Datasheet. The configuration needed is:– SB18, SB19, SB20 open– -R56, R57, C20, C21, X3 soldered

• Oscillator from external PH0 (from external oscillator through pin 10 of the P2 connector)The configuration needed is:– SB19 closed, SB18 open, R56 removed– SB20, R57, C20, C21, X3 = don't care

• No external oscillator (from Internal oscillator HSI only). PH0 and PH1 can be used as GPIO. The configuration needed is:– SB18 open, SB19 closed, SB20 closed, R56 removed, R57 removed– C20, C21, X3 = don't care

4.11.2 OSC 32 KHz clock supplyThe following information indicates all configurations for the 32 kHz clock supply selection.• Oscillator on board (from X2 Crystal, not provided).

The configuration needed is:– SB16 open, SB17 open.– R53, R54, C23, C24, X2 soldered.

• Oscillator from external PC14 (from external oscillator through pin 9 of P1 connector) The configuration needed is:– SB16 closed, R53 removed– SB17, R54, C23, C24, X2 = don't care

• No external oscillator (PC14 and PC15 can be used as GPI.The configuration needed is:– SB16 closed, SB17 closed, R53 removed, R54 removed.– C23, C24, X2 = don't care.


18/35 DocID025175 Rev 1

4.12 Solder bridgesTable 5. Solder bridges

Bridge State (1)

1. Default SBx state is shown in bold.

Description

SB19,20 (X3 crystal)OFF X3, C20, C21, R56 and R57 provide a clock. PH0, PH1 are disconnected from P2

ON PH0, PH1 are connected to P2. Remove only R56 and R57

SB4,6,8,14 (default) ON Reserved, do not modify

SB3,5,7,13 (reserved) OFF Reserved, do not modify

SB22,23,24,25 OFF Reserved, do not modify

SB16,17 (X2 crystal) OFF X2, C23, C24, R53 and R54 deliver a 32 KHz clock. PC14, PC15 are not connected to P2

ON PC14, PC15 are only connected to P2Remove only R53 and R54

SB1 (B2-RESET) ON B2 Push Button is connected to NRST of STM32F429ZIT6

OFF B2 Push Button is not connected to NRST of STM32F429ZIT6

SB2 (B1-USER)ON B1 Push Button is connected to PA0

OFF B1 Push Button is not connected to PA0

SB11,15 (RX,TX)OFF Reserved, do not modify

ON Reserved, do not modify

SB12 (NRST) ON NRST signal of connector CN2 is connected to NRST of STM32F429ZIT6

OFF NRST signal is not connected

SB9 (SWO) OFF SWO signal is not connected

ON SWO signal of connector CN3 is connected to PB3

SB10 (STM_RST) OFF No incidence on NRST signal of STM32F429ZIT6

ON NRST signal of STM32F429ZIT6 is connected to GND

SB21 (BOOT0) ON BOOT0 signal of STM32F429ZIT6 is at level "0" through 510 Ω pull-down

OFF BOOT0 signal of STM32F429ZIT6 is at level "1" through 10 KΩ pull-up (not provided)

SB26,27 (USB OTG) OFF PB14 and PB15 are only used for USB OTG and not connected to P2 to avoid noise

ON PB14 and PB15 are connected to P2.

SB18 (MCO)OFF MCO signal of STM32F429ZIT6 is not used

ON MCO clock signal from STM32F429ZIT6 is connected to OSC_IN of STM32F429ZIT6

DocID025175 Rev 1 19/35


34

4.13 Extension connectorsThe male headers P1 and P2 can connect the STM32F429 Discovery board to a standard prototyping/wrapping board. STM32F429ZIT6 GPI/Os are available on these connectors. P1 and P2 can also be probed by an oscilloscope, a logical analyzer or a voltmeter.

Table 6. MCU pin description versus board function (page 1 of 7)

MCU pin Board function

Main function

LQ

FP

144

Sys

tem

SD

RA

M

LC

D-T

FT

LC

D-R

GB

LC

D-S

PI

L3G

D20

US

B

LE

D

Pu

chbu

tto

n

AC

P/R

F

Tou

ch p

anel

Fre

e I/O

Po

wer

su

pp

ly

CN

2

CN

3

CN

6

P1

P2

BOOT0 138

BO

OT

0

21

NRST 25

NR

ST

RE

SE

T

RE

SE

T

RE

SE

T

B2 5 12

PA0 34 B1 18

PA1 35

INT

1

17

PA2 36

INT

2

20

PA3 37

DB

3

B5 19

PA4 40

VS

YN

C

VS

YN

C

22

PA5 41 21

PA6 42

DB

6

G2 24

PA7 43

AC

P_R

ST

4 23

PA8 100

SC

L

SC

L 3 53

PA9 101 52

PA10 102 51

PA11 103

DB

14

R4 50

PA12 104

DB

15

R5 49

PA13 105

SW

DIO

4 48


20/35 DocID025175 Rev 1

PA14 109

SW

CLK 2 47

PA15 110 INT 46

PB0 46

DB

13

R3 28

PB1 47

DB

16

R6 27

PB2 48

BO

OT

1

30

PB3 133

SW

O

6 28

PB4 134 25

PB5 135

SD

CK

E1

26

PB6 136

SD

NE

1

23

PB7 137 24

PB8 139

DB

4

B6 19

PB9 140

DB

5

B7 20

PB10 69

DB

8

G4 48

PB11 70

DB

9

G5 47

PB12 73 ID 4 50

PB13 74

VB

US

Gre

en 1 49

PB14 75 DM 2 52(1)

PB15 76 DP 3 51(2)

PC0 26

SD

NW

E

14



Main function

LQ

FP

144

Sys

tem

SD

RA

M

LC

D-T

FT

LC

D-R

GB

LC

D-S

PI

L3G

D20

US

B

LE

D

Pu

chbu

tto

n

AC

P/R

F

Tou

ch p

anel

Fre

e I/O

Pow

er s

up

ply

CN

2

CN

3

CN

6

P1

P2

DocID025175 Rev 1 21/35


34

PC1 27 CS 13

PC2 28

CS

X

CS

X

CS

X16

PC3 29 15

PC4 44P

SO 26

PC5 45 QC

Red 25

PC6 96

HS

YN

C

HS

YN

C

57

PC7 97

DB

10

G6 56

PC8 98 55

PC9 99

SD

A

SD

A

1 54

PC10 111

DB

12

R2 45

PC11 112 44

PC12 113 43

PC13 7 12

PC14 8

OS

C32

_IN

9

PC15 9

OS

C32

_OU

T

10

PD0 114 D2 42

PD1 115 D3 41

PD2 116 40

PD3 117

DB

11

G7 39

PD4 118 38

PD5 119 37



Main function

LQ

FP

144

Sys

tem

SD

RA

M

LC

D-T

FT

LC

D-R

GB

LC

D-S

PI

L3G

D20

US

B

LE

D

Pu

chbu

tto

n

AC

P/R

F

Tou

ch p

anel

Fre

e I/O

Pow

er s

up

ply

CN

2

CN

3

CN

6

P1

P2


22/35 DocID025175 Rev 1

PD6 122

DB

0

B2 36

PD7 123 35

PD8 77

D13 54

PD9 78

D14 53

PD10 79

D15 56

PD11 80 TE 55

PD12 81

RD

X 58

PD13 82

WR

X

DC

X 57

PD14 85 D0 60

PD15 86 D1 59

PE0 141

NB

L0 17

PE1 142

NB

L1 18

PE2 1 15

PE3 2 16

PE4 3 13

PE5 4 14

PE6 5 11

PE7 58 D4 37

PE8 59 D5 40

PE9 60 D6 39

PE10 63 D7 42

PE11 64 D8 41

PE12 65 D9 44

PE13 66

D10 43

PE14 67

D11 46



Main function

LQ

FP

144

Sys

tem

SD

RA

M

LC

D-T

FT

LC

D-R

GB

LC

D-S

PI

L3G

D20

US

B

LE

D

Pu

chbu

tto

n

AC

P/R

F

Tou

ch p

anel

Fre

e I/O

Pow

er s

up

ply

CN

2

CN

3

CN

6

P1

P2

DocID025175 Rev 1 23/35


34

PE15 68

D12 45

PF0 10 A0 7

PF1 11 A1 8

PF2 12 A2 5

PF3 13 A3 6

PF4 14 A4 3

PF5 15 A5 4

PF6 18 3

PF7 19

DC

X

SC

L

SC

K

6

PF8 20

MIS

O

5

PF9 21

SD

A

SD

I/SD

O

MO

SI

8

PF10 22

EN

AB

LE

DE 7

PF11 49

SD

NR

AS

32

PF12 50 A6 31

PF13 53 A7 34

PF14 54 A8 33

PF15 55 A9 36

PG0 56

A10 35

PG1 57

A11 38

PG2 87 62

PG3 88 61

PG4 89

BA

0

62

PG5 90

BA

1

61



Main function

LQ

FP

144

Sys

tem

SD

RA

M

LC

D-T

FT

LC

D-R

GB

LC

D-S

PI

L3G

D20

US

B

LE

D

Pu

chbu

tto

n

AC

P/R

F

Tou

ch p

anel

Fre

e I/O

Pow

er s

up

ply

CN

2

CN

3

CN

6

P1

P2


24/35 DocID025175 Rev 1

PG6 91

DB

17

R7 60

PG7 92

DO

TLC

K

CLK 59

PG8 93

SD

CLK

58

PG9 124 33

PG10 125

DB

7

G3 34

PG11 126

DB

1

B3 31

PG12 127

DB

2

B4 32

PG13 128

Gre

en 29

PG14 129

Red 30

PG15 132

SD

NC

AS

27

PH0 23

OS

C_I

N

10

PH1 24

OS

C_O

UT

9

VD

D

22

3 V 5 1

3 V 2

5 V 8 1

5 V 2

GN

D

3 7 5 63 11



Main function

LQ

FP

144

Sys

tem

SD

RA

M

LC

D-T

FT

LC

D-R

GB

LC

D-S

PI

L3G

D20

US

B

LE

D

Pu

chbu

tto

n

AC

P/R

F

Tou

ch p

anel

Fre

e I/O

Pow

er s

up

ply

CN

2

CN

3

CN

6

P1

P2

DocID025175 Rev 1 25/35


34

GN

D

64 29

GN

D

63

GN

D

64

1. If SB27 is On.

2. If SB26 is On.



Main function

LQ

FP

144

Sys

tem

SD

RA

M

LC

D-T

FT

LC

D-R

GB

LC

D-S

PI

L3G

D20

US

B

LE

D

Pu

chbu

tto

n

AC

P/R

F

Tou

ch p

anel

Fre

e I/O

Pow

er s

up

ply

CN

2

CN

3

CN

6

P1

P2

Mechanical drawing UM1670

26/35 DocID025175 Rev 1

5 Mechanical drawing

Figure 9. STM32F429 Discovery board mechanical drawing

DocID025175 Rev 1 27/35

UM1670 Electrical schematics

34

6 Electrical schematics

Figure 10. STM32F429 Discovery board

STMicroelec

tron

ics

Title

:

Num

ber:

Rev:

Sheet o

fB

.1(P

CB

.SC

H)

Date:

8/13

/201

3MB10

751

7

STM32

F429

I-DISCO

NRST

A[0..1

1]D[0..1

5]

SDNE1

NBL1

NBL0

SDNWE

SDNRAS

SDNCAS

SDCLK

SDCKE1

BA0

BA1

U_S

DRAM

SDRAM.SchDoc

PA0

NRST

MEM

S_IN

T1

NCS_

MEM

S_SP

IMEM

S_IN

T2

SPI5_S

CK

SPI5_M

ISO

SPI5_M

OSI

ACP_

RST

I2C3_

SCL

I2C3_

SDA

PG13

PG14

U_IO Peripherals

IO Peripherals.SchDoc

BOOT0

NRST

MCO

D[0..1

5]A[0..1

1]

SDCKE1

SDNE1

SDNWE

NBL0

SDNRAS

NBL1

SDCLK

SDNCAS

BA0

BA1

PA[0..1

5]PB

[0..1

5]PC

[0..1

5]PD

[0..1

5]PE

[0..1

5]

PH[0..2

]

PF[0..15]

PG[0..1

5]

R[0..7

]G[0..7]

B[0..7

]IM

[0..3]

TP_INT1

VSY

NC

CSX

HSY

NC

TE WRX_D

CX

RDX

ENABLE

DCX_S

CL

SDA

I2C3_

SCL

I2C3_

SDA

ACP_

RST

MEM

S_IN

T1

NCS_

MEM

S_SP

IMEM

S_IN

T2

SPI5_S

CK

SPI5_M

ISO

SPI5_M

OSI

OTG

_FS_

IDOTG

_FS_

DM

OTG

_FS_

DP

OTG

_FS_

PSO

OTG

_FS_

OC

VBUS_

FS

DOTC

LK

U_S

TM32Fx

STM32

Fx.SchDoc

OTG

_FS_

PSO

OTG

_FS_

OC

OTG

_FS_

DM

OTG

_FS_

DP

OTG

_FS_

ID

VBUS_

FS

U_U

SB_O

TG_F

SUSB

_OTG

_FS.Sc

hDoc

MCO

BOOT0

NRST

SDNWE

PA0

NRST

PE7

PE8

PE9

PE10

PE11

PE12

PE13

PE14

PE15

PA1

PA2

PA3

PA4

PA5

PA6

PA7

PA0

PB1

PB2

PB10

PB11

PB12

PB13

PB14

PB15

PB0

PC1

PC2

PC3

PC4

PC5

PC0

PD8

PD9

PD10

PD11

PD12

PD13

PD14

PD15

PH1

PH0

BOOT1

/ PB

2

NC

3V3V

3V3V

Rev A.0 --> PC

B label M

B10

75 A-00

Rev B.1 --> PC

B label M

B10

75 B-01,

PA8 - I2C

3_SC

L, P

C9 - I2C

3_SD

A, PG

7 - D

OTC

LK, Y

UY

D

PA13

PA14

NRSTPB3

MCO

PA10

PA9

U_S

T_LINK

ST_L

INK_V

2.SC

HDOC

PA13

PA14

TCK/SWCLK

TMS/SW

DIO

MCO

NRST

T_SW

O

T_NRST

STM32

F4_U

SART1

_TX

STM32

F4_U

SART1

_RX

PA9

PA10

PB3

D[0..1

5]A[0..1

1]

PA[0..1

5]PB

[0..1

5]PC

[0..1

5]PD

[0..1

5]PE

[0..1

5]

PH[0..2

]

PF[0..15]

PG[0..1

5]

D[0..1

5]A[0..1

1]

NBL0

NBL1

BA0

BA1

SDNRAS

SDNCAS

SDCLK

SDCKE1

SDNE1

SDNWE

SDNRAS

SDNCAS

SDCLK

SDCKE1

SDNE1

NBL0

NBL1

BA0

BA1

NRST

B[0..7

]G[0..7]

R[0..7

]

IM[0..3]

TP_INT1

VSY

NC

CSX

HSY

NC

TE WRX_D

CX

RDX

ENABLE

DCX_S

CL

SDA

I2C3_

SCL

I2C3_

SDA

DOTC

LK

U_L

CD-24

LCD-24.Sc

hDoc

VSY

NC

CSX

HSY

NC

TE RDX

WRX_D

CX

DCX_S

CL

SDA

ENABLE

DOTC

LK

VSY

NC

HSY

NC

CSX

TE RDX

SDA

ENABLE

DOTC

LK

DCX_S

CL

WRX_D

CX

B[0..7

]G[0..7]

R[0..7

]

IM[0..3]

TP_INT1

I2C3_

SDA

I2C3_

SCL

NRST

B[0..7

]G[0..7]

R[0..7

]

IM[0..3]

TP_INT1

I2C3_

SDA

I2C3_

SCL

SPI5_S

CK

MEM

S_IN

T1

NCS_

MEM

S_SP

ISP

I5_M

ISO

SPI5_M

OSI

MEM

S_IN

T2I2C3_

SDA

I2C3_

SCL

ACP_

RST

12

34

56

78

910

1112

1314

1516

1718

1920

2122

2324

2526

2728

2930

3132

3334

3536

3738

3940

4142

4344

4546

4748

4950

5152

5354

5556

5758

5960

6162 64

63

P2 Header 3

2X2

ACP_

RST

SPI5_S

CK

MEM

S_IN

T1

NCS_

MEM

S_SP

ISP

I5_M

ISO

SPI5_M

OSI

MEM

S_IN

T2

VBUS_

FS

OTG

_FS_

ID

OTG

_FS_

DM

OTG

_FS_

DP

OTG

_FS_

PSO

OTG

_FS_

OC

PF6

PF7

PF8

PF9

PF10

PF11

PF12

PF13

PF14

PF15

PG0

PG1

PG2

PG3

VBUS_

FS

OTG

_FS_

IDOTG

_FS_

DM

OTG

_FS_

DP

OTG

_FS_

PSO

OTG

_FS_

OC

PG13

PG14

SB27

SB26

BOOT0

PE1

PE2

PE3

PE4

PE5

PE6

PE0

PA8

PA9

PA13

PA14

PA15

PB3

PB4

PB5

PB6

PB7

PB8

PB9

PC6

PC7

PC8

PC9

PC10

PC11

PC12

PC14

PC15

PD1

PD2

PD3

PD4

PD6

PD7

PD0

VDD

PA10

PD5

PC13

5V5V

5V5V

12

34

56

78

910

1112

1314

1516

1718

1920

2122

2324

2526

2728

2930

3132

3334

3536

3738

3940

4142

4344

4546

4748

4950

5152

5354

5556

5758

5960

6162 64

63

P1 Header 3

2X2

PF0

PF1

PF2

PF3

PF4

PF5

PG4

PG5

PG6

PG7

PG8

PG9

PG10

PG11

PG12

PG13

PG14

PG15

PA11

PA12

Electrical schematics UM1670

28/35 DocID025175 Rev 1

Figure 11. ST-LINK/V2 (SWD only)

STMicroelec

tron

ics

Title

:

Num

ber:

Rev:

Sheet o

fB

.1(P

CB

.SC

H)

Date:

8/13

/201

3

12

X1

8MHz

3V

USB

_DM

USB

_DP

STM

_RS

T

T_JTCKT_

JTC

KT_JTDOT_JTDI

T_JT

MS

STM

_JTM

S

STM_JTCK

OSC

_IN

OSC

_OU

T

T_NRST

AIN

_13V

3V

3V

SWIM_IN

SWIM_IN

SWIM_IN

SWIM

SWIM

SWIM_RST_INSWIM_RST

MB10

752

7

STM32

F429

I-DISCO ST-LINK/V2 (S

WD only)

USB

ST-LINK

U5V

COM

5VU5V

3V

PWR

5V

JP1

Wired on So

lder Side

JP2

3V

Jumper

s ON --> D

ISCOVERY S

elec

ted

Jumper

s OFF

-->

ST-L

INK S

elec

ted

VBAT

1

PA7 17

PC13

2

PA12

33PC

143

PB0 18

PC15

4JTMS/SW

DIO

34

OSC

IN5

PB1 19

OSC

OUT

6

VSS

_235

NRST

7

PB2/BOOT1 20

VSS

A8

VDD_2

36

VDDA

9

PB10 21

PA0

10

JTCK/SWCLK37

PA1

11

PB11 22

PA2

12

PA15/JTDI38

PA3 13

VSS_1 23

PA4 14

PB3/JTDO39

PA5 15

VDD_1 24

PA6 16

PB4/JNTRST40

PB12

25

PB541

PB13

26

PB642

PB14

27

PB743

PB15

28

BOOT044

PA8

29

PB845

PA9

30

PB946

PA10

31

VSS_347

PA11

32

VDD_348

U2

STM32

F103

C8T

6

Boa

rd Id

ent:

PC

13=0

T_JT

CK

T_JT

MS

SWD

3V

1234

CN4

SB4

SB3

SB6

SB5

SB8

SB7

SB14

SB13

STM

_JTM

S

STM

_JTC

KSW

CLK

SWDIO

SWD

RESERVED

DEFAULT

3V

T_S

WD

IO_I

N

LED

_STL

INK

LED

_STL

INK

3V

PA13

PA14

TCK/SWCLK

TMS/SW

DIO

VDD

3V

Not Fitted

MC

O

C2

1μF_

X5R

_060

3

C3

10nF

_X7R

_060

3

C5

1μF_

X5R

_060

3

MCO

Not Fitted

T_JRST

1 2 3 4 5 6

CN2

Header 6

AIN

_1

T_N

RST

T_S

WO

NRST

SB12

T_N

RST

SB10

RC M

ust b

e very close to

STM

32F103 pin 29

JP3

51

2

GND

3

4

BYPA

SSIN

H

Vin

Vou

t

U1

LD39

85M33

R

D2

BAT6

0JFILM

D3

BAT6

0JFILM

D1

BAT6

0JFILM

Idd

EXT_

5V, Inp

ut only

JP4

TX RX

STLINK_R

X

Not Fitted

SB15

SB11

PA10

PA9

STM32

F4_U

SART1

_TX

STM32

F4_U

SART1

_RX

Close to

JP

Not Fitted

STLINK_TX

USB

_DM

USB

_DP

3VVCC

1

D-

2

D+

3

ID4

GND

5

SHEL

L6

CN1

USB

-MIN

I-typeB

T_S

WO

PB3

SB9

T_S

WO

EXT_

3V, Inp

ut only

Red

_Green

21

34

LD1

LD_B

ICOLO

R_C

MS

R10

1K5

R12

0R11

0R9

100K

R4

1K

R2

100

R1

100

R3

0

R13

[NA]

R14

22

R15

22

R17

22

R20

22

R28

100

R16

100

R5

10K

R6

10K

R21

100K

R8

100K

R7

10K

R18

4K7

R19

4K7

C27

100n

FC4

100n

FC46

100n

FC47

100n

F

C18

20pF

C16

20pF

C17

20pF C9

100n

F

C1

100n

FC6

100n

F

LD2

LED, red

DocID025175 Rev 1 29/35


34

Figure 12. USB OTG_FS

STMicroelec

tron

ics

Title

:

Num

ber:

Rev: B

.1(P

CB

.SC

H)

Date:

8/13

/201

3MB10

75

STM32

F429

I-DISCO U

SB_O

TG_F

S

5VOTG

_FS_

PSO

OTG

_FS_

OC

3V

1 2

LD6

Red

OTG

_FS_

DM

OTG

_FS_

DP

OTG

_FS_

ID

C53

4.7u

F

OTG

_FS_

PowerSw

itchO

nOTG

_FS_

OverC

urrent

1 2

LD5

Green

3V

3V

Dz

A2

IDA3

Pd1

B1

Pup

B2

Vbu

sB3

D+in

C1

Pd2

C2

D+o

utC3

D-in

D1

GND

D2

D-out

D3

U7

EMIF02

-USB

03F2

GND

2

IN5

EN4

OUT

1FA

ULT

3U8

STMPS

2141

STR

VBUS_

FS

OTG

_FS_

ID

OTG

_FS_

DM

OTG

_FS_

DP

OTG

_FS_

PSO

VBUS_

FS

OTG

_FS_

OC

R66

[N/A

]

R69

0

R73

620

R68

47K

R71

10K

R72

0

R64

22R63

22R67

0

R65

47K

R70

330

3

1

2

T1 9013

-SOT2

3VBUS

1

DM

2

DP

3

ID4

GND

5

Shield

6

USB_Micro-AB receptacle

CN6

USB

-MIC

RO-A

B


30/35 DocID025175 Rev 1

Figure 13. SDRAM 64 Mbits

STMicroelec

tron

ics

Title

:

Num

ber:

Rev:

Sheet

B.1

(PC

B.S

CH

)Date:

8/13

/201

3MB10

754

STM32

F429

I-DISCO SDRAM 64M

bits

WE

16

DQ14

51

GNDQ

6GNDQ

12

DQ13

50DQ12

48

DQ8

42

DQ1

4

RAS

18

DQ9

44

GNDQ

52

DQ7

13

DQ4

8

DQ11

47DQ10

45

DQ3

7

UDQM

39

DQ15

53

VDD

27

DQ0

2

BA1

21

DQ5

10

DQ6

11

CLK

38

CS

19

DQ2

5

GND

28GND

41

A9

34

VDD

1

VDD

14

CAS

17

A7

32

A11

35

A8

33

BA0

20

A0

23

A1

24

GNDQ

46

A10

22

A6

31

CKE

37

A4

29

A5

30

A2

25

A3

26

GND

54VDDQ

3VDDQ

9VDDQ

43VDDQ

49

LDQM

15

NC

36NC

40

U6

IS42

S164

00J

A[0..1

1]

A0

A1

A2

A3

A4

A5

A6

A7

A8

A9

A10

A11

D0

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

D11

D12

D13

D14

D15

D[0..1

5]

3V

Plac

e cl

ose

SDR

AM

SDNWE

SDNRAS

BA0

BA1

SDCLK

SDNCAS

SDCKE1

SDNE1

NBL0

NBL1

3V

SDNE1

SDNWE

SDNRAS

SDNCAS

SDCLK

SDCKE1

NBL0

NBL1

BA0

BA1

D[0..1

5]

A[0..1

1]

C50 100nF

C7 100nF

C8 100nF

C51 100nF

C10 100nF

C15 100nF

C22 100nF

DocID025175 Rev 1 31/35


34

Figure 14. STM32F429ZIT6 MCU

STMicroelec

tron

ics

Title

:

Num

ber:

Rev:

Sheet o

fB

.1(P

CB

.SC

H)

Date:

8/13

/201

3MB10

755

7

STM32

F429

I-DISCO - ST

M32

F429

ZIT6

MCU

PB5

PB6

PB7

PA4

PA5

PA6

PA7

VDD

PA11

PA12

PA9

PA10

PB12

PB13

PB14

PB15

PB10

PB11

PB8

PA0

PB9

PA1

PB1

PB2

PA15

PB3

PB0

PA3

PA13

PA14

PB4

PA2

PA8

BOOT0

NRST

BOOT0

SB21

NRST

L1 BEA

DC26

1uF

VDD

C25

1uF

PC0

PE0

PD0

PC14

-OSC

32_IN

PC15

-OSC

32_O

UT

PE2

1

PE3

2

PE4

3

PE5

4

PE6

5

PH0-OSC

_IN

23

PH1-OSC

_OUT

24

NRST

25

PA0-WKUP1

34

PA1

35

PA2

36

PA3

37

PA4

40

PA5

41

PA6

42

PA7

43

PB0

46

PB1

47

PB2/BOOT1

48

PE7

58

PE8

59

PE9

60

PE10

63

PE11

64

PE12

65

PE13

66

PE14

67

PE15

68

PB10

69

PB11

70

PB12

73

PB13

74

PB14

75

PB15

76

PD8

77

PD9

78

PD10

79

PD11

80

PD12

81

PD13

82

PD14

85

PD15

86

PA8

100

PA9

101

PA10

102

PA11

103

PA12

104

PA13

105

PA14

109

PA15

110

PD0

114

PD1

115

PD2

116

PD3

117

PD4

118

PD5

119

PD6

122

PD7

123

PB3

133

PB4

134

PB5

135

PB6

136

PB7

137

BOOT0

138

PB8

139

PB9

140

PE0

141

PE1

142

PC13

-WKUP2

7

PC14

-OSC

32_IN

8

PC15

-OSC

32_O

UT

9

PC0

26

PC1

27

PC2

28

PC3

29

PC4

44

PC5

45

PC6

96

PC7

97

PC8

98

PC9

99

PC10

111

PC11

112

PC12

113

PF2

12

PF3

13

PF4

14

PF5

15

PF6

18

PF7

19

PF8

20

PF9

21

PF10

22

PF11

49

PF12

50

PF13

53

PF14

54

PF15

55

PF0

10

PF1

11

PG2

87

PG3

88

PG4

89

PG5

90

PG6

91

PG7

92

PG8

93

PG9

124

PG10

125

PG11

126

PG12

127

PG13

128

PG14

129

PG15

132

PG0

56

PG1

57

U5A

STM32

F429

ZIT6

VBAT

6

VSS

_516

VDD_5

17

VSS

A31

VDD_1

230

VREF

+32

VDDA

33

VSS

_438

VDD_4

39

VCAP1

71

VDD_1

72

VSS

_210

7

VDD_2

108

PDR_O

N14

3

VDD_3

144

VDD_1

012

1VDD_9

95

VDD_6

52

VDD_7

62

VDD_8

84

VDD_1

113

1

VSS

_10

120

VSS

_994

VSS

_651

VSS

_761

VSS

_883

VSS

_11

130

VCAP2

106

U5B

STM32

F429

ZIT6

PD1

PD2

PD3

PD4

PD5

PD6

PD7

PD8

PD9

PD10

PD11

PD12

PD13

PD14

PD15

PE1

PE2

PE3

PE4

PE5

PE6

PE7

PE8

PE9

PE10

PE11

PE12

PE13

PE14

PE15

PC1

PC2

PC3

PC4

PC5

PC6

PC7

PC8

PC9

PC10

PC11

PC12

PC13

PF0

PF1

PF2

PF3

PF4

PF5

PF6

PF7

PF8

PF9

PF10

PF11

PF12

PF13

PF14

PF15

PG0

PG1

PG2

PG3

PG4

PG5

PG6

PG7

PG8

PG9

PG10

PG11

PG12

PG13

PG14

PG15

PH0-OSC

_IN

PH1-OSC

_OUT

MCO

PH1-OSC

_OUT

SB20

SB19

MCO

12

X3

8MHz

Not Fitted

PC14

-OSC

32_IN

PC15

-OSC

32_O

UT

SB17

SB16

SB18

PH0-OSC

_IN

C42

2.2u

FC41

2.2u

F

PA[0..1

5]PA

[0..1

5]

PB[0..1

5]PB

[0..1

5]

PC[0..1

5]PC

[0..1

5]

PD[0..1

5]PD

[0..1

5]

PE[0..1

5]PE

[0..1

5]

PH[0..2

]PH

[0..2

]

PF[0..15]

PF[0..15]

PG[0..1

5]PG

[0..1

5]

D[0..1

5]

A[0..1

1]

D[0..1

5]

A[0..1

1]

VDD

A0

A1

A2

A3

A4

A5

A6

A7

A8

A9

A10

A11

SDNWE

SDNRAS

BA0

BA1

SDCLK

SDNCAS

SDCKE1

SDNE1

PF0

PF1

PF2

PF3

PF4

PF5

PF12

PF13

PF14

PF15

PG0

PG1

PC0

PF11

PG8

PG15

PB5

PG4

PG5

PB6

D0

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

D11

D12

D13

D14

D15

NBL0

NBL1

PE0

PD14

PE7

PD8

PE8

PE9

PE10

PE11

PE12

PE13

PE14

PE15

PD9

PD10

PD15

PD0

PD1

PE1

SDCKE1

SDNE1

SDNWE

NBL0

SDNRAS

NBL1

SDCLK

SDNCAS

BA0

BA1

PH0

PH1

PC14

PC15

PA3

PA4

PA6

PA11

PB1

PB8

PB9

PB10

PC6

PC7

PC10

PD2

PA12

PB0

PB11

PC2

PD3

PD4

B5

VSY

NC

G2

R4

R6

B6

B7

G4

HSY

NC

G6

R2

IM0

R5

R3

G5

CSX

G7

IM1

PD5

PD6

PD7

PD11

PD12

PD13

PF7

PF9

PF10

PG6

PG7

IM2

B2

IM3

TE RDX

SDA

ENABLE

R7

DOTC

LK

PG10

G3

PG11

B3

PG12

B4

DCX_S

CL

WRX_D

CX

R[0..7

]R[0..7

]

G[0..7]

G[0..7]

B[0..7

]B[0..7

]

R0

R1

G0

G1

B0

B1

IM[0..3]

IM[0..3]

VSY

NC

CSX

HSY

NC

TE WRX_D

CX

RDX

ENABLE

DOTC

LK

DCX_S

CL

SDA

I2C3_

SDA

I2C3_

SCL

TP_INT1

PA15

PA8

PC9

TP_INT1

I2C3_

SCL

I2C3_

SDA

ACP_

RST

PA7

ACP_

RST M

EMS_

INT1

SPI5_S

CK

MEM

S_IN

T1

NCS_

MEM

S_SP

INCS_

MEM

S_SP

IMEM

S_IN

T2

SPI5_S

CK

SPI5_M

ISO

SPI5_M

OSI

SPI5_M

ISO

SPI5_M

OSI

MEM

S_IN

T2PC

1

PF7

PF8

PF9

PA1

PA2

SB25

SB24

SB23

SB22

VBUS_

FSOTG

_FS_

ID

OTG

_FS_

DM

OTG

_FS_

DP

PB14

PB12

PB15

PB13

OTG

_FS_

PSO

PC4

PC5

OTG

_FS_

OC

OTG

_FS_

ID

OTG

_FS_

DM

OTG

_FS_

DP

OTG

_FS_

PSO

OTG

_FS_

OC

VBUS_

FS

C20

20pF

C21

20pF

C23

6.8p

F

C24

6.8p

F

R56

0

R57

220

R53

0

R54

0

C34 100nF

C35 100nF

C36 100nF

C37 100nF

C38 100nF

C39 100nF

C40 100nF

C29 100nF

C32 100nF

C43 100nF

C44 100nF

C45 100nF

C33 100nF C28

1uF

R52 0

C31

100n

F

C30

100n

FR58

0

R59

[N/A

]

R61

510

4 1

3 2

X2

MC30

6-G-06Q

-32.76

8


32/35 DocID025175 Rev 1

Figure 15. Peripherals

STMicroelec

tron

ics

Title

:

Num

ber:

Rev: B

.1(P

CB

.SC

H)

Date:

8/13

/201

3MB10

75

STM32

F429

I-DISCO Periphe

rals

MEM

S

VDD

SB2

PA0

USE

R &

WAKE-

UP Button

NRST

NRST R

ESET

Button

VDD

SB1

Not Fitted

PA0

MEM

S_IN

T1

3V

SPI5_S

CK

MEM

S_IN

T1

NCS_

MEM

S_SP

INCS_

MEM

S_SP

I

VDD_IO

1

GND

13C1

14

GND

8GND

9

VDD

16

CS_

I2C/SPI

5

INT1

7DRDY/IN

T26

GND

10GND

11

SA0/SD

O4

SDA/SDI/S

DO

3SC

L/SP

C2

VDD

15

GND

12

U3

L3GD20

C13

10uF

C19

10nF

/25V

MEM

S_IN

T2

SPI5_S

CK

SPI5_M

ISO

SPI5_M

OSI

SPI5_M

ISO

SPI5_M

OSI

12

34

56

78

CN3

SSM-104

-L-D

H

3V

AC

P/R

F E

2P C

onne

ctor

5VACP_

RST

I2C3_

SDA

I2C3_

SCL

ACP_

RST

I2C3_

SCL

I2C3_

SDA

MEM

S_IN

T2

R24

100K

R22

220K

R23

330

R25

100

12

LD4

Red

12

LD3

Green

PG13

LEDs

PG13

PG14

PG14

R26

510

R27

680

C12

100n

F

C11

100n

F

C48

100n

F

1 234

B2SW-PUSH-CMS_BLACK

1 234

B1SW-PUSH-CMS_BLUE

DocID025175 Rev 1 33/35


34

Figure 16. LCD 2.4”

STMicroelec

tron

ics

Title

:

Num

ber:

Rev:

Sheet o

fB

.1(P

CB

.SC

H)

Date:

8/13

/201

3MB10

757

7

STM32

F429

I-DISCO LCD 2.4"

SPI5_M

OSI

SPI5_S

CK

3V

3V3V

TP_INT1

XR

YD

YU

XL

Def

ault

I2C

Add

ress

:100

0001

Y-

1

INT

2

A0/Data Out

3

SCLK

4

SDAT

5

VCC

6

Data in

7

IN0

8IN

19

GND

10

IN2

11IN

312

X+

13

Vio

14

Y+

15X-

16

U4

STMPE

811Q

TR

TP_INT1

3V

HSY

NC

VSY

NC

DOTC

LK

3V

C14

4.7u

F

VDD

ENABLE

32

DOTC

LK31

HSY

NC

33

VSY

NC

34

CSX

38

DCX/SCL

37

TE11

WRX/D

CX

36

RDX

35

RES

ET39

DB0/B0

29

DB1/B1

28

DB2/B2

27

DB3/B3

26

DB4/B4

25

DB5/B5

24

DB6/G0

23

DB7/G1

22

VDD3_

P(nc)

8

BC_C

TRL(nc)

9

BC(nc)

10

VDD3

7

IM3

43IM

242

IM1

41IM

040

SDA

30

VCI

6

LEDA

44

LEDK1

45

LEDK2

46

LEDK3

47

LEDK4

48

YD

3

XL

2

YU

1

XR

4GND

5

DB8/G2

21

DB9/G3

20

DB10

/G4

19

DB11

/G5

18

DB12

/R0

17

DB13

/R1

16

DB14

/R2

15

DB15

/R3

14

DB16

/R4

13

DB17

/R5

12

CN5

SF-TC24

0T-937

0-T

XR

YD

YU

XL

B2

B3

B4

B5

G2

G3

G4

G5

R2

R3

R4

R5

ENABLE

CSX

RDX

TE DCX_S

CL

WRX_D

CX

SDA

NRST

IM0

IM1

IM2

IM3

B[0..7

]

G[0..7]

R[0..7

]

NRST

B6

B7

G6

G7

R6

R7

B0

B1

G0

R0

G1

R1

IM[0..3

] = 0110 -->

4-wire

8-bit seria

l I, SDA:In/Out

VSY

NC

HSY

NC

CSX

TE RDX

SDA

ENABLE

DOTC

LK

IM[0..3]

IM[0..3]

DCX_S

CL

WRX_D

CX

R[0..7

]

G[0..7]

B[0..7

]

VSY

NC

CSX

HSY

NC

TE WRX_D

CX

RDX

ENABLE

DOTC

LK

DCX_S

CL

SDA

I2C3_

SDA

I2C3_

SCL

I2C3_

SCL

I2C3_

SDA

R46

100K

R29

4K7

R30

4K7

R45

4K7

R34

100K

R31

4K7

R33

100K

R39

[N/A

]R32

100K

R40

0

R50

0

R51

4K7

R62

4K7

R60

4K7

R55

4K7

R35

[N/A

]R36

4K7

R37

4K7

R38

[N/A

]

R42

[N/A

]R43

[N/A

]

R41

4K7

R44

4K7

C52

100n

F

R49

0R48

0R47

0

C49

100n

F

Revision history UM1670

34/35 DocID025175 Rev 1

7 Revision history

Table 7. Document revision history

Date Revision Changes

10-Sep-2013 1 Initial release.

DocID025175 Rev 1 35/35

UM1670

35

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve theright to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at anytime, without notice.

All ST products are sold pursuant to ST’s terms and conditions of sale.

Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes noliability whatsoever relating to the choice, selection or use of the ST products and services described herein.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of thisdocument refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party productsor services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of suchthird party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIEDWARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIEDWARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWSOF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.

ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USEIN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITHPRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS ORENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNEDFOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED INWRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE,AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS.PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THECORRESPONDING GOVERNMENTAL AGENCY.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately voidany warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, anyliability of ST.

ST and the ST logo are trademarks or registered trademarks of ST in various countries.Information in this document supersedes and replaces all information previously supplied.

The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

© 2013 STMicroelectronics - All rights reserved

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America

www.st.com

Figure 1. STM32F429 Discovery board1 Conventions2 Quick start2.1 Getting started2.2 System requirements2.3 Development toolchain supporting the STM32F429 Discovery kit2.4 Order code

3 Features4 Hardware layoutFigure 1. Hardware block diagramFigure 2. Top layoutFigure 3. Bottom layout4.1 STM32F429ZIT6 microcontroller

Figure 4. STM32F429ZIT6 packageFigure 5. STM32F429ZIT6 block diagram4.2 Embedded ST-LINK/V2

Figure 6. Typical configuration4.2.1 Using ST-LINK/V2 to program/debug the STM32F429ZIT6 on board

Figure 7. STM32F429 Discovery board connections image4.2.2 Using ST-LINK/V2 to program/debug an external STM32 application

Figure 8. ST-LINK/V2 connections image4.3 Power supply and power selection4.4 LEDs4.5 Pushbuttons4.6 USB OTG supported4.7 Gyroscope MEMS (ST MEMS L3GD20)4.8 TFT LCD (Thin-film-transistor liquid-crystal display)4.9 64-Mbit SDRAM (1Mbit x 16-bit x 4-bank)4.10 JP3 (Idd)4.11 OSC clock4.11.1 OSC clock supply4.11.2 OSC 32 KHz clock supply

4.12 Solder bridges4.13 Extension connectors

5 Mechanical drawingFigure 9. STM32F429 Discovery board mechanical drawing6 Electrical schematicsFigure 10. STM32F429 Discovery boardFigure 11. ST-LINK/V2 (SWD only)Figure 12. USB OTG_FSFigure 13. SDRAM 64 MbitsFigure 14. STM32F429ZIT6 MCUFigure 15. PeripheralsFigure 16. LCD 2.4”7 Revision history

figure 1. stm32f429 discovery board€¦ · 13/08/2013 · docid025175 rev 1 7/35 um1670 hardware...

Documents