MECHANICAL PROJECTS

NO PROJECT TITLE / SUPERVISOR DESCRIPTION PICTURES

1 PROJECT TITLE Fabrication Of Beam Pumping Mechanism (DIPLOMA PROJECT) SUPERVISOR Dr.Sabareesaan K.J

Beam Pump is a ground drive for a reciprocating piston

pump in an oil well. Because of high viscosity of liquid, beam pump

is used to bring it out. The engineering term for this type of

mechanism is a walking beam. It is used to mechanically lift liquid

out of the well if there is not enough bottom hole pressure for the

liquid to flow all the way to the motor to a vertical reciprocating

motion to drive the pump shaft. The project consists of different

parts which are: The Base, Counter weight, Horse head, Legs, and

waking beam.

In this project work, we make an attempt to fabricate the

beam pumping mechanism to exhibit its functionality and it can be

used for demonstration purpose in oil and gas labs.

2 PROJECT TITLE Fabrication of Angle Clamp (DIPLOMA PROJECT) SUPERVISOR Mr.Shabbir Ahmed R.M

In the field of manufacturing and design Engineering, There

are many varieties of clamps are available in market like single

screw angle clamp, double screw angle clamp ,welding clamp etc.

for many different purposes. Some are temporary, as used to

position components while fixing them together, others are intended

to be permanent. A clamp is a fastening device used to hold or

secure objects tightly together to prevent movement or separation

through the application of inward pressure. Hence an attempt has

been made to fabricate an angle clamp by considering mild steel as

a material.

 

A welding angle clamp is a heavy-duty model, which is

specially designed for welding corners. This clamp has a

particularly strong and sturdy design, as welding involves joining

two parts together through fusion, an act which puts a lot of

pressure on to the clam. And also An angle clamp can be used to

assemble a variety of different joints like Mitre joint, T joint and butt

joint.

3

PROJECT TITLE Fabrication Of Roof for Painting Area (DIPLOMA PROJECT) SUPERVISOR Mr. Nasser alhinai

         

Fabrication of roof which made from steel frame and

covered by profile sheet. This roof area divided two partitions one

side need to be used for Painting projects and other side for storing

scrap and not in use or Dismantled projects.

The roof designed to reflect sunlight and getting shade

while working in this area and protect from water rain effectively.

4 PROJECT TITLE Fabrication Of Welding Demonstration Table With Vice (DIPLOMA PROJECT) SUPERVISOR Mr. Darsan Rajeevan Sheela

Welding is one of the jointing methods in manufacturing

process. Welding exercise is included in various courses in diploma

level in mechanical engineering. Idea of the project in as per the

requirement from the welding workshop.

There are some limitations while demonstration the

exercise for students with current welding rig. Current setup is

covered from three sides. Which create problems while

demonstration the exercise to all the students. So, we enquired the

requirement with lecturers and technicians who hand the course

.Immediately found assemble demonstration table will help in

solving the problems.

5 PROJECT TITLE Fabrication Of Air Engine (ADVANCE DIPLOMA PROJECT) SUPERVISOR Mr. Nasser Al-Ruqeishi

In the emerging technologies, in the field of hydraulics and

pneumatics, air engine is a type of motor, which does mechanical

work by expanding compressed air. Pneumatic motors generally

convert the compressed air energy to mechanical work through

either linear or rotary motion and vice versa.

Linear motion can come from either a diaphragm or a

piston actuator, while rotary motion is supplied by either a vane

type air motor, piston air motor, air turbine or gear type motor.

Hence with the advent of this technology, in the present

investigation an attempt has been made to fabricate an air engine,

using acrylic as a base material also by using CNC machine.

Initially we design structure of air engine using AUTOCAD and

converting to CNC program by using CNC router machine. Finally

finishing operation will be done by using different machines.

6 PROJECT TITLE Design and Fabrication Of Beam Engine Mechanism (ADVANCE DIPLOMA PROJECT) SUPERVISOR Mr. Nasser Al-Ruqeishi

The   project   was   all   about   designing   and   fabrication   of  

beam  engine  mechanism.    

                           It   is   used   to   convert   rotary   motion   into   linear   motion  (respecting).  

7 PROJECT TITLE Fabrication and Design Of Napier Deltic Engine                               (ADVANCE DIPLOMA PROJECT) SUPERVISOR Mr. Nasser Al-Ruqeishi

It   is   a   use   to   lubricate   the   part   of   an   engine   .Its   use   to  

make  the  movement  of  the  parts  easily  and  in  the  fast  way.  It’s  the  part  of  the  main  construction  of  the  machine.    

 This   part   it   include   in   the   controlling   the   speed   of   the  

machine.    

8 PROJECT TITLE Design & Fabrication of Stairs Trolley (ADVANCE DIPLOMA PROJECT) SUPERVISOR Mr. Nasser Al-Ruqeishi

 The   project   attempts   to   design   the   stair   climbing   trolley  

which   can   carry   heavy   objects   up   the   stairs   with   less   effort  compared  to  carrying  them  manually.    

 The  main  objective  of  the  project  is  to  find  an  efficient  and  

user  friendly  method  of  carrying  various  movement  while  climbing  the  stairs.    

9 PROJECT TITLE Fabrication and Analysis Of Condenser (B.TECH PROJECT) SUPERVISOR Dr. R. Senthil Kumar

 A   vapor-­‐compression   refrigeration   system,   in   which   the  

refrigerant   undergoes   phase   changes,   is   one   of   the   many  refrigeration   cycles   and   is   the  most   widely   used  method   for   air-­‐conditioning   of   buildings   and   automobiles.   It   is   also   used   in  domestic  and  commercial  refrigerators,  large-­‐scale  warehouses  for  chilled   or   frozen   storage   of   foods   and  meats,   refrigerated   trucks  and   railroad   cars,   and   a   host   of   other   commercial   and   industrial  services.    

 The  condenser  plays  an  important  role  in  the  refrigeration  

system  to  condense  vapor  refrigerant  to  liquid.  So,  the  condenser  to  be  designed   for   the  given   refrigerant   conditions  and  analyzing  for  its  maximum  performance.  

 The  design  has  been  done  in  Phase  I  to  attain  the  details  of  

condenser   and   the   performance   has   been   estimated   in   Phase   II  with   fabricated   shell   and   tube   system.   A   try   was   made   with   a  refrigerant   R134A   and   finally   used   water   steam   experiment   the  system.  

   Results   have   been   analyzed   from   the   data   taken   during  

experimentation  and  effectiveness  was  found. 10

PROJECT TITLE Hands-On Modeling and Analysis Of Shredder Machine (B.TECH PROJECT) SUPERVISOR Mr.Prabaharan T

Shredder  machine   is  used  to  cut   the  materials   into  either  strips   of   small   parts.   We   focus   on   shredding   the   waste   plastic  water  bottle  that  dumped  in  our  college  canteen.  

   The   waste   of   plastic   &   aluminium   can   increases   day   by  

day  and  causes  a  lot  of  environmental  pollution.      Nowadays,  the  whole  world  is  moving  towards  recycling  &  

saving  the  nature.  Our  shredder  machine  reduces  heap  amount  of  pollution   and   help   Colleges   free   from  waste.   In   order   to   achieve  objective,   we   made   an   optimum   design   of   portable   shredder  machine  with  necessary  calculations  and  validating  the  same  result  using  Ansys  software  package.    

11 PROJECT TITLE Design and Fabrication Of Reverted Gear Train (B.TECH PROJECT) SUPERVISOR Dr.V.Selvakumar

 This  project  will  be  out  to  explore  the  practicality  of  power  

trans-­‐mission  between  co-­‐axial  shafts.  Reverted  gearbox  is  widely  used   in   industrial  machineries  and  machine  tools   to  obtain  speed  reduction,  which  in  turn  increases  the  torque.  Reverted  gearboxes  are  used  in  many  applications  such  as  power  transmission  system  and  hybrid  transmission  systems.    

 In  this  reverted  gear  train  mechanism  power  transmission  

takes  places  between  two  co-­‐axial  shafts.  Reverted  gear  is  a  widely  used   industrial   product   in   mid-­‐level   precision   industry,   such   as  printing   lathe,   automation   assembly,   semi-­‐conductor   equipment  and   automation   system.   Planetary   gearing   could   increase   torque  and  reduce  load  inertia  while  minimized  the  speed.  The  aim  of  this  project   is   to   design   and   fabricate   the   reverted   gear   train.   The  reverted   gear   train   is   designed   to   be   used   in   lab   for   conducting  experiments.  

OIL AND GAS PROJECTS

NO PROJECT TITLE / SUPERVISOR DESCRIPTION

1 PROJECT TITLE Brief Study On Lost Circulation & Recommendation For Avoidance. SUPERVISOR Mr.CHANDILYAN.S.U  

 The   project   study   titled   “Brief   study   on   lost   circulation   &   recommendation   for   avoidance"  

aims  to  understand  what  is  lost  circulation  and  the  problem  caused  by  lost  circulation  and  to  suggest  suitable  solution  for  better  work  in  oil  and  gas  fields.    

 The  project  summarizes  the  definition  and  types  of  lost  circulation,  location  of  lost  circulation,  

causes,  prevention  &  effects  of  lost  circulation.  Moreover,   it   is  about  the  lost  circulation  assessment  and  planning,  future  for  identifying  lost  circulation,  control  lost  circulation  and  lost  circulation  martial.  Furthermore,  our  recommendation  concludes  the  project  on  how  to  prevent  lost  circulation.

2 PROJECT TITLE Recent Trends In Drilling Technology SUPERVISOR Mr. Mohammes Ismail Iqbal  

 The  project  chosen  is  advancement  in  Drilling  Technology.  We  covered  the  sub  heading  of  the  

project  (advancements  in  drilling  technology):  Directional  Drilling:  Working  principle,  problems  &  solution,  advantages  &  disadvantages  and  

case  study.  Casing   while   Drilling:  Working   principle,   problems   &   solution,   advantages   &   disadvantages  

and  case  study.  Managed   Pressure   Drilling:   Working   principle,   problems   &   solution,   advantages   &  

disadvantages  and  case  study.  

2 PROJECT TITLE Enhancing Recovery Using Well Stimulation Technique. SUPERVISOR Mr. Mohammes Ismail Iqbal  

 This  project   is   titled   (Enhancing  oil  Recovery  using  well   stimulation  Technology)   is  aiming  to  

understand  what   is  well   stimulation  and  how  we  can   improve   the  well  by  using   it   and   study   topics  related   to   the  well   stimulating.   Also   this   section   provides   background   information   on   the   currently  available  well  treatment  technologies  for  increasing  the  rate  of  oil  flow  from  the  reservoir  to  the  well.  It   is  used  for  situations  where  the  natural  reservoir  flow  need  to  perform  the  three  commonly  used  well  stimulation  method.