finepix s5100, s5500 service manual

THE COMPONENTS IDENTIFIED BY THE MARK “ ” ON THE SCHEMATICDIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY.PLEASE REPLACE ONLY BY THE COMPONENTS SPECIFIED ON THE SCHEMATICDIAGRAM AND IN THE PARTS LIST.IF YOU USE PARTS NOT SPECIFIED, IT MAY RESULT IN A FIRE AND ANELECTRICAL SHOCK.

FUJI PHOTO FILM CO., LTD.Ref.No.:ZM00574-102

Printed in Japan 2005.11

DIGITAL CAMERA

FinePix S5100/S5500/

US/CA/EU/EG/GE/AS/CH-ModelSERVICE MANUAL

WARNING

2

FinePix S5100/S5500 Service Manual

7. CAUTION: FOR CONTINUEDPROTECTION AGAINST FIREHAZARD, REPLACE ONLY WITHSAME TYPE 2.5 AMPERES 125VFUSE.

ATTENTION: AFIN D'ASSURERUNE PROTECTIONPERMANENTE CONTRE LESRISQUES D'INCENDIE,REMPLACER UNIQUEMENTPAR UN FUSIBLE DE MEME,TYPE 2.5 AMPERES, 125 VOLTS.

8. WARNING: TO REDUCE THEELECTRIC SHOCK, BECAREFUL TO TOUCH THEPARTS.

WARNING! HIGH VOLTAGE

SAFETY CHECK-OUTAfter correcting the original problem, perform the followingsafety check before return the product to the customer.

1. Check the area of your repair for unsoldered or poorlysoldered connections. Check the entire board surfacefor solder splasher and bridges.

2. Check the interboard wiring to ensure that no wires are“pinched” or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularlytransistors, that were installed during a previous repair.Point them out to the customer and recommend theirreplacement.

4. Look for parts which, though functioning, show obvioussigns of deterioration. Point them out to the customerand recommend their replacement.

5. Check the B + voltage to see it is at the valuesspecified.

6. Make leakage - current measurements to determinethat exposed parts are acceptably insulated from thesupply circuit before returning the product to thecustomer.

2.5A 125V

2.5A 125V

RISK OF FIRE-REPLACE FUSEAS MARKED

3

TABLE OF CONTENTSFinePix S5100/S5500 Service Manual

TABLE CONTENTS

1. General ........................................................... 41-1. Product specification .............................................. 41-2. Explanation of Terms .............................................. 71-3. Names of External Components ............................ 8

2. Disassembly ................................................. 102-1. Names of internal Components ............................ 102-2. Removing the CABI REAR ASSY ........................ 112-3. Removing the LCD ASSY..................................... 122-4. Removing the EVF UNIT CONST ........................ 132-5. Removing the MAIN PWB ASSY.......................... 132-6. Removing the BATTERY HOLDER ASSY ........... 152-7. Removing the DCST PWB ASSY ......................... 162-8. Removing the LENS CONST ............................... 162-9. Removing the STROBE CONST .......................... 172-10. Removing the AF FRAME ASSY .......................... 18

3. Schematics ................................................... 193-1. Cautions ............................................................... 193-2. Basic Block Names and Functions ....................... 193-3. Description of Main Block Functions .................... 20

3-3-1. Technical Overview ................................. 203-4. Block Diagram ...................................................... 213-5. Overall connection Diagram ................................. 223-6. Circuit Diagrams ................................................... 23

3-6-1. CAM BLOCK........................................... 233-6-2. DCDC BLOCK ........................................ 243-6-3. KSW BLOCK .......................................... 253-6-4. LCD EVF BLOCK ................................... 263-6-5. MOTOR BLOCK ..................................... 273-6-6. PROCESS BLOCK ................................. 283-6-7. CCD FPC BLOCK................................... 293-6-8. IPS STROBE BLOCK ............................. 303-6-9. MSW BLOCK .......................................... 313-6-10. RSW BLOCK .......................................... 31

3-7. Mounted Parts Diagrams ...................................... 323-7-1. DCST PWB ASSY .................................. 323-7-2. MAIN PWB ASSY ................................... 343-7-3. KSW FPC ASSY ..................................... 363-7-4. MSW FPC ASSY .................................... 383-7-5. RSW FPC ASSY ..................................... 403-7-6. CCD FPC ASSY ..................................... 41

4. Adjustment.................................................... 424-1. Important point Adjustment when

Replacing Major Parts .......................................... 424-2. Measuring Instruments Used ............................... 424-3. Use Jig list ............................................................ 424-4. Calibration method of pattern box ........................ 434-5. Adjusting soft installation ...................................... 43

4-5-1. Various downloading softwaredecompressions, preservation methods,and notes ................................................ 43

4-5-2. Installation of DSC jig driver ................... 444-5-3. Adjusting soft initiation method ............... 44

4-6. Initial Settings of the Adjustment Software ........... 454-7. Starting the Adjustment Software ......................... 484-8. [R] : Flash Memory Reset ..................................... 514-9. [F9] : AF-Assist Light Adjustment ......................... 534-10. [F5] : CAMERA Adjustment .................................. 564-11. [F4] : CCD Defect Correction ............................... 594-12. [F6] : AF Adjustment ............................................. 614-13. [F1] : Battery Voltage Adjustment ......................... 644-14. [F7] : Flash Adjustment ......................................... 684-15. [F11] : Video Adjustment ...................................... 704-16. [F8] : Firmware Download .................................... 724-17. [F12] : End Setting ................................................ 74

5. Inspection ..................................................... 785-1. Required Measuring Equipment ........................... 785-2. Connection of Measuring Equipment ................... 785-3. Inspection and Factory Settings ........................... 79

6. Parts List ....................................................... 816-1. Packing and Accessories ..................................... 81

6-1-1. US-model (FinePix S5100) ..................... 816-1-2. CA-model (FinePix S5100) ..................... 826-1-3. EU-model (FinePix S5500) ..................... 836-1-4. EG-model (FinePix S5500) ..................... 846-1-5. GE-model (FinePix S5500) ..................... 856-1-6. AS-model (FinePix S5500) ..................... 866-1-7. CH-model (FinePix S5500) ..................... 87

6-2. Cabi Front block ................................................... 886-2-1. US/CA-model (FinePix S5100) ............... 886-2-2. EU/EG/GE/AS-model (FinePix S5500) ... 896-2-3. CH-model (FinePix S5500) ..................... 90

6-3. Inner block ............................................................ 916-4. Cabi Rear block .................................................... 926-5. Electrical parts ...................................................... 93

7. Appendix....................................................... 947-1. Function of display for Firmware Version ............ 947-2. List of Related Technical Updates Issued ............ 95

4

1. General FinePix S5100/S5500 Service Manual

1. General1-1. Product specificationSystem

Model Digital camera FinePix S5100/FinePix S5500Effective pixels 4.0 million pixelsCCD 1/2.7 inch square pixel CCD Number of total pixels: 4.23 million pixelsNumber of recorded pixels Still image: 2272 × 1704 pixels/1600 × 1200 pixels/1280 × 960 pixels/

640 × 480 pixels ( / / / )Movie: 640 × 480 pixels (30 frames per second with monaural sound)

320 × 240 pixels (30 frames per second with monaural sound)Storage media xD-Picture Card (16/32/64/128/256/512 MB)File format Still image: Compressed: JPEG (Exif ver. 2.2)

Uncompressed: CCD-RAW (RAF) * Design rule for Camera File System compliant DPOF compatible

Movie: AVI format, Motion JPEGAudio: WAVE format, Monaural sound

Lens Fujinon 10× optical zoom lens, F2.8-F3.1Aperture F2.8-F8 10 steps at wide-angle/F3.1-F9 10 steps at telephoto in 1/3 EV increments

Manual/Auto selectableFocal length f=5.7 mm to 57 mm (Equivalent to 37 mm to 370 mm on a 35 mm camera)Digital zoom : approx. 1.4× / : approx. 1.8× / : approx. 3.6×

(10× optical zoom lens is used together: Max. zoom scale: 35.5×)Focal range Normal: Wide-angle: Approx. 90 cm (3.0 ft.) to infinity

Telephoto: Approx. 2.0 m (6.6 ft.) to infinityMacro: Wide-angle: Approx. 10 cm to 2.0 m (3.9 in. to 6.6 ft.)

Telephoto: Approx. 90 cm to 2.0 m (3.0 ft. to 6.6 ft.)Shutter speed / / / /P: 1/4 sec. to 1/2000 sec. /S: 3 sec. to 1/1000 sec.

A: 1/4 sec. to 1/1000 sec. M: 15 sec. to 1/2000 sec.Focus TTL contrast-type, Auto focus, Manual focusSensitivity : AUTO (Equivalent to ISO 64 to 320, depending on coditions) 64/100/200/400

/ / / /P/S/A/M: Equivalent to ISO 64/100/200/400(During setting CCD-RAW: ISO 64/100/200)

Photometry TTL 64-zones metering Multi, Spot, AverageExposure control Program AE ( , P, , , , ), Shutter-priority AE, Aperture-priority AE, Manual exposureExposure compensation -2.0 EV to +2.0 EV in 1/3 EV step increments

(in Programmed auto, shutter-priority auto, Aperture-priority auto)White balance Auto ( , , , , ) Manual modes, 8 positions can be selected (P, S, A, M)Viewfinder 0.33 inches, 115,000 pixels electronic viewfinder, Approx. 100% coverageLCD monitor 1.5 inches, low-temperature polysilicon TFT 115,000 pixels, Approx. 100% coverageFlash type Auto flash using flash control sensor

Effective range: Wide-angle: Approx. 30 cm to 5.0 m (1.0 ft. to 16.4 ft.) (Approx. 30 cm to 2.0 m (1.0 ft. to 6.6 ft.): Macro)

Telephoto: Approx. 80 cm to 4.5 m (2.6 ft. to 14.8 ft.)Flash modes: Auto, Red-eye reduction, Forced flash, Suppressed flash, Slow synchro,

Red-eye reduction + Slow synchroSelf-timer Approx. 2 sec./10 sec.Continuous shooting Top 3-frame: Number of recorded frames: up to 3 frames

(at intervals as short as approx. 0.3 sec.)Final 3-frame: Number of recorded frames:

last 3 frames before releasing the shutter button (at intervals as short as approx. 0.3 sec.)

Long-period continuous shooting Number of recorded frames: up to 40 frames (at intervals as short as approx. 0.6 sec.)

Shooting functions Best framing, Frame No. memoryPlayback functions Trimming, Automatic playback, Multi-frame playback, Voice memoOther functions PictBridge, Language ( , English, Francais, Deutsch, , Italiano, ), FinePix

photo mode ( -mode), WEB camera, Discharge batteriesA/V output NTSC/PAL selectable

5

1. GeneralFinePix S5100/S5500 Service Manual

Power Supply and Others

Power supply Use one of the following:• 4× AA-size alkaline batteries• 4× AA-size Ni-MH (Nickel-Metal Hydride) batteries (sold separately)• AC Power Adapter AC-5VH/AC-5VHS (sold separately)

According to the CIPA (Camera & Imaging Products Association) standard procedure formeasuring digital still camera battery consumption (extract):When using alkaline batteries, use the batteries supplied with the camera. You can useNi-MH batteries also. The storage media should be xD-Picture Card.Pictures should be taken at a temperature of 23oC (+73oF), with the LCD monitor/viewfinder (EVF) turned on, the optical zoom moved from full wide-angle to full telephoto(or vice-versa) and back again to its original position every 30 seconds, the flash used atfull power every second shot and the camera turned off and then on again once every 10shots.• Note: Because the number of available shots varies depending on the capacity of alkaline

batteries or the level of charge in Ni-MH batteries, the figures shown here for thenumber of available shots using batteries are not guaranteed.

The number of available shots will also decline at low temperatures.Conditions for use Temperature : 0oC to +40oC (+32oF to +104oF) ; 80% humidity or less (no condensation)Camera dimensions 112.7 mm × 81.1 mm × 79.3 mm/4.4 in. × 3.2 in. × 3.1 in.(W×H×D) (not including accessories and attachments)Camera mass (weight) Approx. 340 g/12.0 oz. (not including accessories, batteries and xD-Picture Card)Weight for photography Approx. 480 g/16.9 oz. (including batteries and xD-Picture Card)Accessories AA-size alkaline batteries (LR6) (4)

16 MB, xD-Picture Card (1) Included with: Anti-static case (1) Shoulder strap (1) A/V cable for FinePix S5100/FinePix S5500 (1)

approx. 1.5 m (4.9 ft.), plug (2.5 mm dia.) to pin-plug ×2 USB cable (mini-B) (1) Adapter ring AR-FX5A (1) Lens cap (1) CD-ROM (1) Software for FinePix AX Owner’s Manual (1)

Optional accessories xD-Picture CardDPC-16 (16 MB)/DPC-32 (32 MB)/DPC-64 (64 MB)/DPC-128 (128 MB)/DPC-256 (256 MB)/DPC-512 (512 MB)

Rechargeable Battery 2HR-3UF (2×) Battery Charger with Battery BK-NH/BK-NH2 (With Euro type or UK type plug) AC Power Adapter AC-5VH/AC-5VHS Soft Case SC-FXS5 Image Memory Card Reader DPC-R1

• Compatible with Windows 98/98 SE, Windows Me, Windows 2000 Professional,Windows XP or iMac, Mac OS 8.6 to 9.2, Mac OS X (10.1.2 to 10.2.2) and modelsthat support USB as standard.

• Compatible with xD-Picture Cards of 16 MB to 512 MB, and SmartMedia of 3.3 V,4 MB to 128 MB.

PC Card Adapter DPC-AD• Compatible with xD-Picture Card of 16 MB to 512 MB, and SmartMedia of 3.3 V, 2

MB to 128 MB. CompactFlash Card Adapter DPC-CF

• Windows 95/98/98 SE/Me/2000 Professional/XP• Mac OS 8.6 to 9.2/X (10.1.2 to 10.1.5)

xD-Picture Card USB Drive DPC-UD1• Compatible with xD-Picture Card of 16 MB to 512 MB• Windows 98/98 SE/Me/2000 Professional/XP• Mac OS 9.0 to 9.2/X (10.0.4 to 10.2.6)

Guide to the number ofavailable frames forbattery operation

Alkaline batteries Approx. 200 frames

Ni-MH batteries 2300 mAh Approx. 400 frames

Battery Type With LCD monitor ON

6


Input/Output Terminals

A/V output socket 2.5 mm dia. jack USB socket For file transfer to a PC

DC input Socket for specified AC power adapter AC-5VH/AC-5VHS (sold separately)

Standard number of available frames/recording time per xD-Picture CardThe number of available shots, recording time or file size varies slightly depending on the subjects photographed. Note alsothat the difference between standard number of frames and the actual number of frames is greater for xD-Picture Cards with higher capacities.

Quality Setting

Number of recordedpixels

DPC-16 (16 MB)

1600 1200

25

640 480

122

2272 1704

1

50 247 3

101 497 7

204 997 15

F

2272 1704

8

16

33

66

134

268

N

16

32

66

132

266

532

409

818

1280 960

33

68

137

275

550

1101

1997

3993

30

61

Movie

640 480

13 sec.

Image Data Size 620 KB 130 KB 8.3 MB1.9 MB 960 KB 460 KB

27 sec.

55 sec.

111 sec.

223 sec.

7.4 min.

Movie

320 240

26 sec.

54 sec.

109 sec.

219 sec.

7.3 min.

14.6 min.

DPC-32 (32 MB)

DPC-64 (64 MB)

DPC-128 (128 MB)

DPC-256 (256 MB)

DPC-512 (512 MB)

7


AF/AE Lock On the FinePix S5100/FinePix S5500, pressing the shutter button down half way locksthe focus and exposure settings (AF and AE lock). If you want to focus on a subject thatis not centered in the frame or change the picture composition after the exposure is set,you can obtain good results by changing the composition after the AF and AE settingsare locked.

Auto power save function If the camera is not used in any way for 60 seconds, this function turns features such asthe LCD monitor/viewfinder (EVF) off (sleep mode) to prevent battery depletion and thewaste of power when the AC power adapter is connected. If the camera is then leftunused for a further period, the Auto power save function turns the camera off. Thisperiod can be set to 2 or 5 minutes on this camera.• The Auto power off function does not operate in PC mode, during automatic playback,

or if it is disabled during setup.Deactivated batteries: Leaving an Ni-MH battery unused in storage for a long period may cause a rise in the

level of substances that inhibit current flow inside the battery and result in a dormantbattery. A battery in this state is referred to as deactivated.Because current flow is inhibited in a deactivated Ni-MH battery, the battery’s originallevel of performance cannot be achieved.

DPOF: Digital Print Order FormatDPOF is a format used for recording information on a storage media (image memorycard, etc.) that allows you to specify which of the frames shot using a digital camera areto be printed and how many prints are made of each image.

EV: A number denotes Exposure Value. The EV is determined by the brightness of thesubject and sensitivity (speed) of the film or CCD. The number is larger for brightsubjects and smaller for dark subjects. As the brightness of the subject changes, adigital camera maintains the amount of light hitting the CCD at a constant level byadjusting the aperture and shutter speed.When the amount of light striking the CCD doubles, the EV increases by 1. Likewise,when the light is halved, the EV decreases by 1.

Frame rate (fps): The frame rate refers to the number of images (frames) that are photographed or playedback per second. For example, when 10 frames are continuously photographed in a 1-second interval, the frame rate is expressed as 10 fps.For reference, TV images are displayed at 30 fps (NTSC).

JPEG: Joint Photographics Experts GroupA file format used for compressing and saving color images. The higher the compressionrate, the greater the loss of quality in the decompressed (restored) image.

Memory effect: If an Ni-MH battery is repeatedly charged without first being fully discharged, its perfor-mance may drop below its original level. This is referred to as the “memory effect”.

Motion JPEG: A type of AVI (Audio Video Interleave) file format that handles images and sound as asingle file. Images in the file are recorded in JPEG format. Motion JPEG can be playedback by QuickTime 3.0 or later.

PC Card: A generic term for cards that meet the PC Card Standard.PC Card Standard: A standard for PC cards determined by the PCMCIA.PCMCIA: Personal Computer Memory Card International Association (US).Smear: A phenomenon specific to CCDs whereby white streaks appear on the image when there

is a very strong light source, such as the sun or reflected sunlight, in the photographyscreen.

WAVE: A standard format used on Windows systems for saving audio data. WAVE files havethe “.WAV” file extension and the data can be saved in either compressed oruncompressed format. Uncompressed recording is used on this camera.WAVE files can be played back on a PC using the following software:Windows: MediaPlayerMacintosh: QuickTime Player

* QuickTime 3.0 or laterWhite Balance: Whatever the kind of the light, the human eye adapts to it so that a white object still

looks white. On the other hand, devices such as digital cameras see a white subject aswhite by first adjusting the color balance to suit the color of the ambient light around thesubject. This adjustment is called matching the white balance.

Exif Print: Exif Print Format is a newly revised digital camera file format that contains a variety ofshooting information for optimal printing.

1-2. Explanation of Terms

8


Exposure compensation

button

Focus mode selector button Mode dial

Continuous shooting

button

Power switchShutter button

Focus mode selector lock switch

W (Wide zoom) button

Photo mode( )

button

DISP (display)/BACK

button

Low light

viewfinder button

Battery cover

MENU/OK button

4-direction ( ) button

T (Tele zoom) button

Strap mount

Viewfinder (EVF)

Diopter adjustment dial

EVF/LCD

(monitor selector)

button

Tripod mount

LCD monitor

Indicator lamp

/ (Macro) button

/ (Flash) button

1-3. Names of External Components

9


Flash pop-up button

Strap mount

Slot cover

USB socket (mini-B)

DC IN 5V (power input) socket

A/V OUT (Audio / Visual output) socket

Self-timer lamp

Microphone

Flash

Flash control sensor

AF-Assist

illuminator

Speaker

xD-Picture Card slot

Lens

10

2. Disassembly FinePix S5100/S5500 Service Manual

2. Disassembly2-1. Names of internal Components

CABI REAR ASSY

LCD ASSY

LENS CONST

MAIN PWB ASSY

CABI FRONT ASSY

BATTERY HOLDER ASSY

STROBE CONST

MIC ASSY

SPEAKER ASSY

EVF UNIT CONST

RSW PWB ASSY

MAIN FRAME

DCST PWB ASSY

LCD FRAME

AF FRAME ASSY

KSW PWB ASSY

MSW PWB ASSY

11

2. DisassemblyFinePix S5100/S5500 Service Manual

2-2. Removing the CABI REAR ASSY

[Disassembly]1. Remove the three screws (M1.7 x 3.5).

2. Remove the two screws (M1.7 x 5).

3. Open the battery cover.

4. Raise the CABI REAR ASSY in the direction of thearrow.

1

1

2

3

4

5. Remove the FFC.

[Assembly]Set the mode dial to the camera position and assemble it.Assemble in the reverse order to disassembly.

5

12


2-3. Removing the LCD ASSY

[Disassembly]1. Remove the two screws (M1.7 x 2.5).

3. Raise the LCD ASSY in the direction of the arrow.

[Assembly]Assemble in the reverse order to disassembly.

1

2

3

2. Remove the connector.

13


2-5. Removing the MAIN PWB ASSY

[Disassembly]1. Remove the connector.

2. Remove the three FFCs.

3. Raise the NAIN PWB in the direction of the arrow.

12

2

3

2-4. Removing the EVF UNIT CONST


2. Raise the EVF UNIT CONST in the direction of thearrow.

3. Remove the FFC.


1

2

3

14


4

[Assembly]Make the style of FFC and the lead wire as shown in figurebelow.

4. Remove the FFC.

15


2-6. Removing the BATTERY HOLDER ASSY


2. Remove the screw (M1.7 x 8.0).

3. Remove the BATTERY HOLDER ASSY in the directionof the arrow.

1

2

3

[Assembly]Set the switch lever to the off position when assembling. OFF

Note:Always ensure that the FLASH ASSY main condenser isdischarged before beginning disassembly.

16


2-7. Removing the DCST PWB ASSY


2. Remove the FFC.

3. Remove the two connectors.

4. Remove the DCST PWB ASSY in the direction of thearrow.

1

2

3

4

[Assembly]Put the substrate aside in the direction of the arrow whenassembling.

2-8. Removing the LENS CONST


2. Remove the MAIN FRAME.

3. Remove the LENS CONST in the direction of the arrow.


1

2 3

17


2-9. Removing the STROBE CONST

[Disassembly]1. Remove the ST-BUTTON.

1

2

3

42. Remove the screw (M1.7 x 5.5).

3. Remove the connector.

4. Remove in the STROBE CONST direction of the arrow.

[Assembly]Make read-wire a style as shown in the figure below.Assemble in the reverse order to disassembly.

18


1

2

2-10. Removing the AF FRAME ASSY

[Disassembly]1. Remove two screws.

2. Remove the AF FRAME ASSY in the direction of thearrow.

[Assembly]Execute the AF-Assist Light Adjustment after assembling.

19

3. SchematicsFinePix S5100/S5500 Service Manual

3. Schematics3-1. Cautions

<Cautions when replacing parts>• Do not reuse removed parts. Always use new parts.

• Note that the negative side of tantalum condensers is readily damaged by heat.

• Except for chemical condensers and tantalum condensers, voltage is not displayed on condensers with a voltageresistance of 50V or less.

• Resistors not marked are 1/16W chip resistors.

• KΩ = 1000Ω, MΩ = 1000KΩ

• B characteristics of variable resistors and semi-fixed resistors are not displayed.

3-2. Basic Block Names and FunctionsPart name Block name Function

LENS CONST CCD FPC BLOCK CCD output(IC701)MAIN PWB ASSY CAM BLOCK CCD output A/D conversion (IC103), CCD driver (IC101, IC102)

PROCESS BLOCK Image signal processing, USB communications,system control (IC201), Image signal processing assist (IC202)

LCD/EVF BLOCK LCD/EVF output control (IC401)VIDEO BLOCK VIDEO output (IC51)AUDIO BLOCK Audio IN/OUT (IC11)

DCST PWB ASSY DC/DC BLOCK Power supply generation (IC503)IPS BLOCK Power ON function, Flash charging control,Key function (IC301)MOTOR BLOCK Shutter/Iris/AF/zoom drive (IC651)

RSW PWB ASSY RSW BLOCK Power SW, Shutter SWKSW PWB ASSY KSW BLOCK Key SWMSW PWB ASSY MSW BLOCK Mode SWSTOROBE ASSY FLASH BLOCK Flash

20

3. Schematics FinePix S5100/S5500 Service Manual

3-3. Description of Main Block Functions3-3-1. Technical OverviewCCD signal processing/Camera circuit section

Analog signals output from the 1/1.7 type square pixels CCD (IC701), with an effective pixel count of 4.0 mega-pixels,undergo false color compensation processing, adaptive interpolation processing, amplification (AGC) and signalmixing inside the CCD signal processing IC “AFE (IC103)” before being converted to 14-bit digital signals (A/D) andsent to the signal processing LSI “UCS2 (IC201)”.The vertical drive IC (IC101) for driving the CCD and the horizontal drive IC (IC102) are in this block.

Motor Circuit SectionThe signal processing LSI “UCS2 (IC201)” that has received various operating switch commands manages the motordrive IC (IC651) and controls the AF, SHUTTER, ZOOM and IRIS motors.

Imaging and Signal Processing SectionInput data from the CCD14-bit digital image data (corresponding to 1H) that has been output from the imaging section (CCD/Camera Block) issent to the signal processing LSI “UCS2 (IC201)”, converted to 32-bit (16-bit x 2) data by the [internal buffer] inside thisLSI, and the image data for one frame (2272 x 1704 pix) is stored temporarily in [SD-RAM]. It is also integrated in the[AUTO operation section] using the 32-bit the signal processing LSI “UCS2 (IC301)” image data and sent to theAFE_IC (IC103) to obtain the appropriate AE/AF/AWB.Record processing to xD CardImage data stored in SD-DRAM “IC203” is sent one frame at a time to the internal [signal processing section] in thesignal processing LSI “UCS2 (IC201)”. In a process called unpacking, “32-bit to 12-bit conversion” and “pre-processing including digital clamp, white balance and noise reduction processing, linear matrix processing, gammacorrection and R/G/B 14-bit to R/G/B 8-bit conversion” to “8-bit digital R/G/B signals to Y:Cb:Cr = 4:2:2 YC processing”are implemented in this [signal processing section] and 8-bit Y/Cb/Cr image data are sent to the [internal buffer].* Noise reduction processing, linear matrix processing and gamma correction included here are processed by the

Partner chip.The “rearrangement of data in a format in which 8-bit Y/Cb/Cr signals are easily compressed” is done in the [internalbuffer] and after passing through the [JPEG operation block] to the [media controller], they are recorded on the xD card.Reproduction of images from xD cardCompressed image data from the xD card is sent as 8-bit image data to the signal processing LSI “UCS2 (IC201)”then it is sent to the [media control section], the [DMA unit] and the SD-DRAM “IC203” and then it is sent to the [mediacontroller], to the [JPEG operation section] and to the [signal processing section].In the [signal processing section], 8-bit Y/Cb/Cr signals are converted to 8-bit R/G/B signals and at the same time,lettering display signals are weighted and passed through the [LCD controller to the LCD/EVF unit and displayed.Image capture system adjustment data are stored in the Flash ROM (IC204).

LCD/EVF UnitDigital signals sent from the signal processing LSI “UCS2 (IC201)” are sent LCD/EVF drive IC (IC401), controls LCD/EVF.

Power Supply SectionPower supply circuits constructed in the core of the DC IC (IC503) create the following power supplies, which aresupplied to each block.

D3.3V [IC651 (MOTOR BLOCK), IC203 (SDRAM), IC201 (UCS2), IC204 (Flash Rom), IC202 (PARTNER), IC301(IPS), LCD (CN401), MODE FPC]

D5.2V [IC651 (MOTOR BLOCK)]-7.5V [IC701 (CCD), IC101 (V_Drv)]15V [IC701 (CCD), IC101 (V_Drv)]CAM3.3V [IC101 (V_Drv), IC102 (RTG),IC103(AFE)]1.5V [IC201 (UCS2), IC202 (PARTNER)]2.5V [IC201 (UCS2)]MOT3.4V [IC651 (MOTOR BLOCK), IC701 (AUDIO BLOCK)]AD_3.3V [IC11 (AUDIO BLOCK), IC51 (VIDEO BLOCK)]

21


3-4. Block Diagram

UCS2 LIBRA (T8K15BXB) IC201

Operation3.3V (I/O), 2.5V, 1.5V

IBFC

TX49 CPU Core

MFT

Audio(A/D)

AUTO

DEBUG I/F

CPU Core

I-cache 16k

BUS Cont.

SDRAMC

DMAC

Periphera

l BU

S 9

6M

Hz

WDT

A/D

LCDDAT[7:0]

LCDHD, LCDVD

LCDCLK,LCD CS

JPEG

RECC

V Drv.

MD2174

ANALOG DEVICES AFE

AD9945

3.3V Operation

CDS ADC

12bit

RTG

FF1178

3.3V Operation

(Programmable)

Motor Drv.

M50236HP

7 ch

SDRAM

256Mb

x 32

FLASH

8MB

EVF, LCD

Driver

LC1500

LCD Panel

1.5inch

BL LED x3

xD CardSlot

(20PIN)

AUDIO IC

BP3602_1

CTL

MIC

SPEAKER

MIC_AMP

SP_AMP

SIO1(U2_SCK,U2_SO,U2_SI)

X’TAL(X202)

CX-101F

27.00MHz

X’TAL(X201)

CX-101F

48.00MHz

Cont.

Pulses

ØV

CCD_CLK (27MHz)

CC

DIN

KEY SW

R/L/D/U SW

OK/BACK/DISP SW

EVF/LCD SW

TELE/WIDE SW

F-mode SW

F_HP, Z_HP, MOT_EXT_F, MOT_MOB_(F,Z,I)

Detect system

EV3

Video

Driver

CCD_ON

IPS_ACT, IPS_CS, STRB_CC, STRB_SY

RESET

ST

RB

_S

Y

BEEP

VIDEO_ON

VBS_OUT

AUDIO_OUT

EVF BL

EVF

0.33inch

AV Jack

SIO1

(U2_SO,U2_SCK)

SIO1

(U2_SCK

U2_SO)

10xZOOM LENS

f=5.7~57.0mm

F=2.8~3.1 O.L

PF

CCD IC701

IC103

IC101

IC651

IC102

ICX448DQ

1/2.7inch

4.0millon pixels

USB Jack

xD Card

STRB-XE

DC IN

5V

BATT.

AA x 4

P-TR

BATT

Backup

DC/DC Block

DC/DC IC. AN30212A

5ch

1.5V

3.3V

5V

CCD15V,-7.5V

LCD

Etc.

PW_CTR

3.3V_ON

LED_R LED_G

IPS

AN30203AA

STROBOCTRL

LED

DRIVER

x 3

RTC

Power on

Reset

CTL

FUSE

32.768kHZ

LED_ST

Partner Chip

FF4183

3.3V(I/O),1.5V Operation

PCCDIF

PMOVC

REGCNT

CLKC

AF ASSIST LED

LENS CONST

RELEASE SW

POWER/CAM/PB SW

RELEASE SW(S1/S2)

CC

D_

AF

E[1

3:0

]

VRESET, CCDLD, CCD_STB, CCDDI

VD, HD, DCLK

AD

CL

K,S

HD

,SH

P,

CP

OB

,PB

LK

AFE_CS

ØH

VSUB_CNT

V Pulss

SIO

1

(U2

_S

CK

, U

2_

SO

)

MOT_RESET, MOT_CLK, MOT_CS

SHT_CLSSHT_OPN

Zo

om

_P

ositio

n

Zo

om

HP

Fo

cu

s H

P

CCD_PC[13:2]

Cont_DAT

DVCLK

CCD_THROUGH

BAT_V, PWR_SW , PWR_SW

PW_SW

VREF

EVR

2ch

CTL

SIO2

(U2_SCK,U2_SO,LD)

EVL_BL_ON

LCD_BL_ON

SIO

2

(CC

D_

SC

K,

CC

D_

SO

)

DR

_S

W

PGA

CGEN

ENCD

TFDCYCPRO

Audio(Seriul)

CCDIF

MEDIA

ICU

PORT

CLKC

Internal

eDRAMA

Internal

eDRAMB

DAC

USB

SIO

RAWNR

IC301

IC503

IC204 IC203

IC11

IC51

IC401

DCST PWB

MAIN PWB

IC202

MODE SW

+/-

FOCUS SW

AF/MF CAF SW

FOCUS SW

POPUP SW

MODE DIAL

I/O Buffer

22


3-5. Overall connection Diagram

V5A

V4V3B

V3A

V2V1

VST

VHDLVL

VL

H2AH1A

CSUB

SUBH2B

H1B

RGCCD +15V

CCD +15V

GNDGND

VOUT

CC

D_

FP

C

CA

M B

LK

FB

1S

02

9J5

1

VOUTGND

V5BV6

GND

GND

GND

1

2

3

4

5

6

7

8

10

9

11

12

13

14

15

16

17

18

20

19

22

21

23

24

25

27

26

29

28

FH12_14S_0.5SH

MIC CAUDIOBLKSM02B_SRPKS_TB

GND 1

2

3

4

5

6

7

8

10

9

11

12

13

14

15

16

17

18

20

19

CARDR/B

RE

CECLE

ALE

WEWP

GND

D0D1

D2

D3D4

D5

D6D7

VCC

VCC

XD

_C

AR

D_

CN

FG

Y0

67

-02

01

EVF UNIT

EVF BLK

EVF FPC18 17 16 15 14 13 12 11 910 8 7 6 5 4 3 2 1

ST

H

VS

S

CK

H2

CK

H2

VD

D

CS

H G R B

DS

G

DC

D

VB

B

CD

V

EN

B

ST

V

CK

V1

CO

M

N.C

18FLT_SM1

EV

F_

BL

SM02B_SRS

LCD FPC1 2 3 4 5 6 7 8 109 11 12 13 14 15 16 17 18 2019 21 22

N.C

CK

H2

CK

H1

HV

DD

ST

H

VS

S

CS

H G R B

AN

OD

E

CA

TH

OD

E

DS

G

DS

D

SC

VB

B

CS

V

EN

B

VV

DD

ST

V

CK

V1

CO

M

LCD UNIT

LCD BLK

FH12_22S_0.5SH

AV

_JA

CK

HS

J1

66

0_

01

95

75

VID

EO

BLK

POWER ON BLKMAIN PWB

PROCESS BLK1

2

3

4

5

6

FS

W_

FF

C

08F

LT

_S

M1

8F

HJ-S

M1-T

B(N

N)

7

8

SPEAKER+

D 3.3VAF/MF/CAF

GND

GND

LED STSTRB_POPUP

SPEAKER-

FS

W_

PW

B

SPEAKER+

D 3.3VAF/MF/CAF

GND

GND

LED STSTRB_POPUP

SPEAKER-

DC CNBATT

HE

C3654_012010

CP

G4702-0

101

USB_CN

51387_0528

RSW PWB

8

7

6

5

4

3

1

2

3

4

5

6

PS

W_

FF

C

GNDAD 2.5V

GNDDRIVE/+-

MODE_DIAL

GND

08F

LZ

_R

SM

1

08F

LT-S

M1-T

B

3 4 5 6 7 8

S1

S2

PLA

Y

EV

3

PW

_S

W

GN

D

RSW FFC3 4 5 6 7 8

8FHT-SM1-TB(NN)

8FLZ_SM1-TB(NN)

21

GN

D

GN

D

1 2

14 13 12 11 10 9 8 7 56

KSW FFC

KSW

PWB

34

9831S-70Y930

9842B-70Y930

1 2 3 4 5 6 7 8 109 11 12 13 14 15 16 17 18 2019 21 22 23 24 25 26 27 28 3029 31 32 33 34 35 36 37 38 4039 41 42 43 44 45 46 47 48 5049

B to B CN

1 2 3 4 5 6 7 8 109 11 12 13 14 15 16 17 18 2019 21 22 23 24 25 26 27 28 3029 31 32 33 34 35 36 37 38 4039 41 42 43 44 45 46 47 48 5049 51 52 53 54 55 56 57 58 6059 61 62 63 64 65 66 67 68 69 70

51 52 53 54 55 56 57 58 6059 61 62 63 64 65 66 67 68 7069

D_3.3

V

EV

3

GN

D

D_3.3

V

GN

D

D3.3

V

CA

M_3.3

V

AU

_3.3

V

CA

M_3.3

V

AU

_3.3

V

CC

D_15V

GN

D

CC

D_15V

GN

D

GN

D

D_1.5

V

GN

D

D_1.5

V

CC

D_ -

7.5

V

D_1.5

V

CC

D_ -

7.5

V

D_5.2

V

D_3.4

V

GN

D

D_3.4

V

GN

D

CC

D_O

N

SH

T_C

LS

NC

(3.3

V_O

N)

SH

T_O

PN

LE

D_S

T

MO

T_R

ES

ET

LE

D_G

Z_H

P

LE

D_R

F_H

P

GN

D

MO

T_C

S

GN

D

MO

T_C

LK

PW

_S

W

MO

T_M

OB

_Z

BA

T_V

MO

T_M

OB

_F

PW

R_

SW

MO

T_M

OB

_I

IPS

_C

S

GN

D

IPS

_A

CT

GN

D

MO

T_E

XT

_Z

RE

SE

T

MO

T_E

XT

_F

U2_1.5

V

MO

T_E

XT

_I

U2_3.3

V

MO

T_

ON

GN

D

N.C

.

GN

D

U2_S

I

ST

RB

_S

Y

U2_S

O

ST

RB

_C

C

U2_S

CK

D+

GN

D

D-

GN

D

VB

US

ZOOM3( B)20

19

18

17

16

15

14

13

11

12

10

9

8

7

6

5

4

3

1

2

ZOOM1( A)

ZOOM4(/B)ZOOM2(/A)

FOCUS3(B)

FOCUS1(A)FOCUS4(/B)

FOCUS2(/A)

IRED(FOCUSSENS(FOCU

VCC(FOCUS)

IG2(/A)IG3( B)

IG1( A)

IG4(/B)SH DRV -

SH DRV +

SENS(ZOOM)VCC (ZOOM)

IRED(ZOOM)

MO

TO

RF

PC

LE

NS

UN

IT

MO

TO

R B

LK

FH

12

_2

0S

_0

.5S

H

ST

RB

BLK

DCST PWB

MSW

PWB

S1

S2

PLA

Y

EV

3

PW

_S

W

GN

D

GN

D

GN

D

2 1

FH12_14S_0.5S

GN

D

DR

IVE

/+-

MO

DE

_D

IAL

GN

D

GN

D

GN

D

LE

D_R

LD

E_G

D_3.3

VO

K/B

CA

K/D

ISP

/E_

L

TE

LE

/WID

E/F

_M

OD

E

R/L

/D/U

AD

_2.5

V

GN

D

2

1

7

8

GNDGND

GNDAD 2.5V

GNDDRIVE/+-

MODE_DIAL

GND

GNDGND

D_3.3

V

EV

3

GN

D

D_3.3

V

GN

D

D3.3

V

CA

M_3.3

V

AU

_3.3

V

CA

M_3.3

V

AU

_3.3

V

CC

D_15V

GN

D

CC

D_15V

GN

D

GN

D

D_1.5

V

GN

D

D_1.5

V

CC

D_ -

7.5

V

D_1.5

V

CC

D_ -

7.5

V

D_5.2

V

D_3.4

V

GN

D

D3.4

V

GN

D

CC

D_O

N

SH

T_C

LS

NC

(3.3

V_O

N)

SH

T_O

PN

LE

D_S

T

MO

T_R

ES

ET

LE

D_G

Z_H

P

LE

D_R

F_H

P

GN

D

MO

T_C

S

GN

D

MO

T_C

LK

PW

_S

W

MO

T_M

OB

_Z

BA

T_V

MO

T_M

OB

_F

PW

R_

SW

MO

T_M

OB

_I

IPS

_C

S

GN

D

IPS

_A

CT

GN

D

MO

T_E

XT

_Z

RE

SE

T

MO

T_E

XT

_F

U2_1.5

V

MO

T_E

XT

_I

U2_3.3

V

MO

T_

ON

GN

D

N.C

.

GN

D

U2_S

I

ST

RB

_S

Y

U2_S

O

ST

RB

_C

C

U2_S

CK

D+

GN

D

D-

GN

D

VB

US

GN

D

DR

IVE

/+-

MO

DE

_D

IAL

GN

D

GN

D

GN

D

LE

D_R

LD

E_G

D_3.3

VO

K/B

AK

C/D

ISP

/E_

L

TE

LE

/WID

E/F

_M

OD

E

R/L

/D/U

AD

_2.5

V

GN

D

1 2 3 4 5 6 7 8 109 1211 13 14

123456

LE

DA

FA

LE

DA

FA

LE

DA

FC

LE

DA

FC

LE

DA

FC

LE

DA

FA

AF LED

1

2

3

4

5

6

7

8

2

1

SPEAKER+

SPEAKER-

1

2

XE+

TRIGGER3

4

XE-

TRIGGER C

ST

RB

UN

IT1 2 3 4 5 6 7 8 9

V_B

US

D-

D+

ID GN

D

FR

AM

E

FR

AM

E

FR

AM

E

FR

AM

E

1 2

UN

RE

G

UN

RE

G_G

N

AF LED BLK

6FHJ-SM-TB(NN)

1 2 3

V_B

US

D-

D+

S04B

_P

AS

_2

MIC_UNIT

SM02B_SRSS_TB

N.C

N.C

23 24

SP

EA

KE

R U

NIT

23


3-6. Circuit Diagrams3-6-1. CAM BLOCK

24


3-6-2. DCDC BLOCK

25


3-6-3. KSW BLOCK

26


3-6-4. LCD EVF BLOCK

27


3-6-5. MOTOR BLOCK

28


3-6-6. PROCESS BLOCK

29


3-6-7. CCD FPC BLOCK

30


3-6-8. IPS STROBE BLOCK

31


3-6-9. MSW BLOCK

3-6-10. RSW BLOCK

32


3-7. Mounted Parts Diagrams3-7-1. DCST PWB ASSY

<SIDE A>

33


<SIDE B>

34


3-7-2. MAIN PWB ASSY

<SIDE A>

35


<SIDE B>

36


3-7-3. KSW FPC ASSY

<SIDE A>

37


<SIDE B>

38


3-7-4. MSW FPC ASSY

<SIDE A>

39


<SIDE B>

40


3-7-5. RSW FPC ASSY

<SIDE A> <SIDE B>

41


<SIDE A> <SIDE B>

3-7-6. CCD FPC ASSY

42

4. Adjustment FinePix S5100/S5500 Service Manual

4. Adjustment4-1. Important point Adjustment when Replacing Major PartsWhen replacing the MAIN PWB or LENS CONST or DCST PWB or STROBE or AF FRAME ASSY, adjust the items markedwith an in the table below. (Other part replacements need not be adjusted. )

Pats.No Name Use RemarksZJ00006-100 Filter LB140 CAMERA adjustment Common with the DS-30/DS-20/DS-7ZJ00477-100 AF chart AF adjustment Common with the FX-6800ZZJ00681-100 Line chart AF-Assist Light adjustment *1 Common with the FinePix S5000ZJ00734-100 Conversion lens (f= 1560.69mm) AF adjustment Common with the FinePix S5000ZJ00735-100 Conversion lens (f= 865.12mm) AF adjustment Common with the FinePix S5000ZJ00736-100 Lens holder (70mm) AF adjustment Common with the FinePix S5000ZJ00008-100 Lens holder AF adjustment Common with the 8mm VTR/MX600ZJ00009-100 Stand AF adjustment Common with the 8mm VTR/MX600ZJ00254-100 Gray Chart (Reflective type) Flash adjustmen Common with the MX700/MX500FZ05266-100 USB cable General adjustment This is bundled to the productFZ05262-100 VIDEO cable Video adjustment This is bundled to the productZJ00840-100 FXS5100/5500 W PC Soft Ver.1.00 PC adjustment Win98 / Me / 2000 / XP English OS *1

ZJ00684-100 DSC JIG Driver Install.exe For PC setup Common with the FinePixF610 *1

ZJ00580-100 Power Cable Jig BATT adjustment New JigZJ00611-100 X-Y stage for AF adjustment AF adjustment Common with the FinePixM603ZJ00653-100 LB140 filter holder kit for X-Y stage General adjustment Common with the FinePixF610ZJ00650-100 VIDEO adjustment jig Video adjustment Common with the FinePixA310ZJ00553-100 AF solid chart General adjustment Common with the FinePixS2ProFZ03983-100 AC Cable (For EG) Use with VIDEO adjustment jig Common with the FinePixA310 *2

FZ03982-100 AC Cable (For EU) Use with VIDEO adjustment jig Common with the FinePixA310 *2

FZ00330-200 AC Cable (For US/JP) Use with VIDEO adjustment jig Common with the FinePixA310 *2

ZJ00581-100 Discharger Discharge for FLASH UNITZJ00525-100 MACRO CHART Resolution inspection Common with the FinePix A201

Replacing parts AF FRAMEAdjustment item MAIN PWB LENS CONST DCST PWB STROBE ASSY0 Flash memory reset *1 AF Assist light adjustment2 CAMERA adjustment3 CCD Defect adjustment4 AF adjustment5 Battery adjustment6 Flash adjustment7 Video adjustment8 Firmware download Do not use it until there is an instruction.9 End setting (Do the end setting when you end the adjustment software when you set the camera to the Jig mode. )

Measuring equipment RemarksRegulated power supply For adjustmentPattern box PTB450Digital voltmeter For Battery adjustmentPC Used for various adjustments and operation checks(PC-AT compatible, Win 98 / Me / 2000 / XP)Brightness meter LS-110 (Minolta) or equivalentColor temperature meter Color Meter IIIF (Minolta) or equivalentFlash meter Used for function checks

* Before making any other adjustments, always reset the flash memory (EVR).

4-2. Measuring Instruments Used

4-3. Use Jig list

*1 : Data available from WEB site.*2 : Select one the power cable suitable for each country.

43

4. AdjustmentFinePix S5100/S5500 Service Manual

4-4. Calibration method of pattern box< Use the pattern box for CAMERA adjustment >Turn on the power supply in the pattern box.Afterwards, wait for about ten minutes so that the source oflight may stabilize.

(1) Brightness:160±5cd/m2 (with LB140 filter)No chart, center of pattern boxMinolta brightness meter LS-110 or equivalent

* Calibration methodPlace the filter (LB140) against the pattern box. With thefilter (LB140) in contact with the brightness meter, adjustthe pattern box brightness to 160±5cd/m2.

(2) Color temperature:aa6100±50 K (with LB140 filter)No chart, center of pattern boxMinolta color meter IIIF or equivalent

* Calibration methodPlace the filter (LB140) against the pattern box. With thefilter (LB140) in contact with the color temperature meter,adjust the pattern box color temperature to 6100 ± 50 K.

4-5. Adjusting soft installation4-5-1. Various downloading software decompressions, preservation methods, and notesThe PC adjustment software are in a specified Web server,and both of these are the compression of ZIP form files.Therefore, after downloading these compression files fromthe Web server, the decompression of the file is necessary.In the decompression software, if the decompression of theZIP form can be done, any software is OK. (Please prepare each one for the decompression software.)The decompression and the preservation method of the PCadjustment software and the firmware are describedto the following.* The PC adjustment soft decompression and preservation

method

<Step1>Download compressed PC adjustment software (ZJ00840-100.ZIP) from Web server (http://fujifilm-di.intranets.com/)<Fig. 4-5-1>.

<Step2>Defrost the downloaded compression software.

(Note)* Specify the preservation drive for C drive if it is

decompression software which can specify the preservationdrive.

* Similarly, defrost without making a new folder if it isdecompression software which can be defrosted withoutmaking a new folder.

* Defrost simply if the decompression software which you havecannot specify the drive specification and the folder making.

<Fig. 4-4-1> Calibration method of pattern box

LB140

Pattern BOX

(All white)

<Fig. 4-5-1> Fujifilm-di.intranets Screen

FXS5100/5500 W PC Soft Ver.1.00 ZJ00840-100.zip

ZJ00840-100

My Computer3.5inch FD(A:)(C:)

FinePixS5100_5500_W

<Fig. 4-5-2>

44


<Step3>The folder named ZJ00840-100 can be made by defrostingwithout specifying anything <Fig. 4-5-2>.Then, copy the folder named FinePixS5100_5500_W in thisfolder in C drive <Fig. 4-5-3>.The folder of ZJ00840-100 becomes unnecessary at theend, and delete this folder.

(Caution)[Important](a) PC adjustment software can not start when there is folder of

FinePixS5100_5500_W in folder named ZJ00840-100 (Fig. 4-5-3).Please preserve the folder of FinePixS5100_5500_W right under C drive (Fig. 4-5-3).

(b) Please do not change the foldername named FinePixS5100_5500.PC adjustment software can not start when foldername is changed.

4-5-2. Installation of DSC jig driver* Since this camera uses the USB for communications with

the personal computer, in order to start the PC adjustmentsoftware, [the DSC jig driver] needs to be installed in thepersonal computer beforehand.

* The DSC jig driver is the same as that for the FinePixS7000, so if this jig driver software is already installed in thepersonal computer, it is not necessary to install it.The procedure is given below.

<Step 1>DSC jig driver (ZJ00684-100.ZIP) is downloaded from Webserver (http://fujifilm-di.intranets.com/).

<Step 2>Defrost the downloaded compression software

<Step 3>Double-click setup.exe in the folder of defrosted ZJ00684-100 and install Fuji FILM DSC Jig Driver as follows.

<Step 4>Install the software in [C:\ProgramFiles\Fjig]according to the instructions on the PC's screen.

4-5-3. Adjusting soft initiation methodWhen the folder has been copied to the C drive, double-clickon the file C:\FinePixS5100_5500_W\ffw.exe (Fig.4-5-5) tostart the adjustment software.

<Fig. 4-5-4>

<Fig. 4-5-5>

(1)

ZJ00840-100

My Computer3.5inch FD(A:)(C:)

FinePixS5100_5500_W

<Fig. 4-5-3>

45


4-6. Initial Settings of the Adjustment Software

* The initial settings are already written in the "FFW.ini" file,therefore perform the following procedure to the letter.Note that, if you change file names, the software will notstart up.

* The initial settings of steps 3 to 6 are already set in the"FFW.ini" file. Therefore, you need only to check them.

* Do not rewrite the user program (FXS5100_5500_W_0.ff).If the program is rewritten, the adjustment software will notstartup.

<Step 1>Double-click on the "FFW.exe" execute file of the adjustmentsoftware to open the "FFW Startup" screen (Fig. 4-6-1).

<Step 2>Click on "Settings" ([1] in Fig. 4-6-2) in the menubar of thestartup window.Then, select "Mode setting" ([2] in Fig. 4-6-2) from the pull-down menu that appears.

<Fig. 4-6-2>

(1) (2)

FinePix S5100/5500_W Adjustment Software Start-up Screen

Select [Start] from [Operate] on the FFW Toolbar

—> The adjustment software starts




<Fig. 4-6-1>

FXS5100_5500_W_0.ff

46


<Step 3>Select the "EVR & Comm" tab ([1] in Fig. 4-6-3) in the"Customize" dialog box that appears.Set the "EVR" items ([2] in Fig. 8) as follows.

Item Detailsetc (-V2) CheckLANC page Check

<Step 4>Select the "Etc" tab ([1] in Fig. 4-6-4) in the "Customize"dialog box that appears. Set the "Other" items ([2] in Fig. 4-6-4) as follows.

Item Details# of auto measure 0Change mode Do not checkUse Japanese font Do not checkDon’t show OK NG Check or Do not check

<Step 5>Select the "Hardware" tab ([1] in Fig. 4-6-5) in the"Customize" dialog box that appears.Input the values for PI and P Board ([2] in Fig. 4-6-5).

PIO 0 10 12 14 16PIO 1 11 13 15 17

Set the "Hardware" items ([3] in Fig. 4-6-5) as follows.

Item DetailsDebug Mode Select [Default]

<Step 6>Once the above settings have been made, click on "Apply"([4] in Fig. 4-6-5) in the "Customize" dialog box to completesetup.This applies the setup, therefore setting is unnecessary fromthe next time forward.

[Note]If [Disable OKNG display] on the PC screen (Fig. 4-6-4) isset to OFF, the PC screen displays [OK] if adjustment isOK,and [NG] if adjustment is NG(either setting is OK).

<Fig. 4-6-3>

(1)(2)

<Fig. 4-6-5>

(2)(1)

(4)(3)

(2)

<Fig. 4-6-4>

47


Menu Command DetailsOperation Start Program start

Stop Program stopTemporary stop Temporary program stopStep 0 Do not useEnd Terminate program

Program Reload Program (*.ff) reloadSelect Program (*.ff) selectEdit Program (*.ff) edit

Data ad[ ] Do not userd[ ] Do not useSW Do not usefsw Do not useEVR Do not use *1)

Mode File record Do not useNGSTOP Program stopped if

adjustment is NGSTEP Do not useLINE Do not useAUTO Do not use

Setting OKNG clear Do not useMode set Sets up modeAutomaticadjustment Execution setting for Auto

Adjust in user programHelp Help Basic software help

FF help User program helpFocus Not used with this

adjustment softwareVersion Version information for

basic software

<Table> FFW.exe Commands

Cautions When Adjusting*1) FinePix S5100/S5500 cannot adjust the EVR data

reading and writing.(Details are right tables.)

*2) End Setting returns the camera from the Jig mode tothe Product Mode.End Setting is required when using the PCadjustment software, even when replacing boards orunits other than those noted above. Failure to runEnd Setting will prevent identification as MassStorage.When the camera is connected to the PC, andprevent communication with the PC.

*3) When all adjustment have been completed, alwayscheck that the camera is identified as Mass Storage.

48


Cautions When Using the FinePix S5100/5500 Adjustment Software1. Adjust as follows after replacing parts.[F1]Battery [F4]CCD Defect Correction [F5]Camera [F6]AF [F7]Flash[F8]Firmware Download [F9]AF-Assist [F11]Video [F12]End Setting| – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – || Replaced Parts Adjustment Procedure || AF FRAME : [F9]->[F12] || LENS CONST : [F5]->[F4]->[F6]->[F1]->[F7]->[F12] || MAIN PWB : [F5]->[F4]->[F6]->[F1]->[F7]->[F11]->[F12] || DCST PWB : [F1]->[F7]->[F11]->[F12] || STROBE : [F7]->[F12] || || – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – |2. When the MAIN PWB ASSY has been replaced, always reset

the flash memory before making any other adjustments.3. Always run End Setting after using this adjustment software.4. Proceed with adjustment after reading the cautions here,

and the relevant cautions noted in the Service Manual.Press the [Enter] key to proceed to the Jig Mode Setup screen.

<Fig. 4-7-2>




<Fig. 4-7-1>

4-7. Starting the Adjustment Software<Step 1>Double-click on [FFW.EXE] (Fig. 4-5-3) in the folder copied to the C drive (see ‘4-5-1. Various downloading softwaredecompressions, preservation methods and notes’) to display the adjustment software start-up screen.

<Step 2>Run the adjustment in accordance with the instructions on the screen.

—> The [Cautions When Using the Adjustment Software] screen appears.

<Step 3>

—> The [Jig Mode Setup] screen appears.

49


<Step 4>

—> The [Firmware version check] screen appears.

<Step 5>

—> The [Adjustment Items Select] screen appears.

<Note>(1) [F1] Battery Adjustment cannot be run unless the Power Cable Jig is used to supply power to the camera.(2) When new MAIN PWB ASSY is replaced, MAIN PWB ASSY is automatically initialized. At that time, wait for one-two

minutes, and advance the adjustment according to the instruction of the adjustment software.

FinePix S5100/5500 Jig Mode Setup Procedure

1). Open the battery cover.2). Connect the Power Cable Jig with the camera.3). Adjust the output current of the power supply to 3.0A or less.4). Adjust the output voltage of the power supply

to 5.0+-0.02V.5). Connect the USB cable with the camera and PC.6). Switch-ON the camera power while pressing the shutter button.7). Check that the LED at the under the viewfinder

is lights in green.

Press the [Enter] key after completing the procedure of (1)-(7).

<Fig. 4-7-3>

FirmWare = 1.28Vendor Name =FUJIFILMManufacturer =FUJIFILMProductName =FinePixDevice Type =CAMERASerialNo =Y-750^^^^^040707C0PX0000000001Frame Work =1.00

Please download a new version if it is necessaryto download the firmware.Advance to the adjustment item selection screenwhen press the [Enter] Key of PC.

<Fig. 4-7-4>

50


FinePix S5100/5500_W adjustment item select screen0.[ R ] : Flash memory reset

*Only use for when the MAIN PWB has been replaced.

1. [ F 9 ] : AF-Assist Light Adjustment2. [ F 5 ] : Camera Adjustment3. [ F 4 ] : CCD Defect Correction4. [ F 6 ] : AF Adjustment5. [ F 1 ] : Battery Voltage Adjustment6. [ F 7 ] : Flash Adjustment7. [ F11 ] : VIDEO Adjustment8. [ F12 ] : End Setting

[ F 8 ] : Firmware Download[Execute this item only when

need to change the firmware.][ X ] : Restart

FXS5100/5500 ADJ Software Ver.1.00<Fig. 4-7-5>

<Step 6>

<Note>(1) ‘FXS5100/5500 W PC Soft Ver.1.00’ at the bottom-right of the screen indicates the version number of the adjustment

software.(2) After running firmware download, other adjustments may be required depending on the content of the download software.

In such cases, the items to be adjusted, and the sequence of adjustment, will be indicated separately.(3) After starting the adjustment software and beginning communication with the camera, always run End Setting following

adjustment and before returning the camera to the customer. If the End Setting is not run, the PC will not recognize thecamera when the two are connected.Reason: As the camera will remain in the Jig mode (repair mode), it will not be recognized with the normal camera drivers.

(4) When the adjustment is interrupted after the [X]:Restart key is pushed, it remains about the Jig mode.

51


4-8. [R] : Flash Memory Reset<Note>Only reset the flash memory when the MAIN PWB ASSY has been replaced.When the MAIN PWB ASSY has been replaced, always reset the flash memory before making any other adjustments.If the flash memory is reset when the MAIN PWB ASSY has not been replaced, all the adjusted data reverts to the defaultsettings.In this event, adjust all the settings.(Excludes firmware downloading.)After the MAIN PWB ASSY has been replaced, proceeding with other adjustments without first resetting the flash memorywill prevent the successful completion of the adjustments.(In some cases the camera may be completely disabled.)If this occurs, set the camera to jig mode again and then reset the flash memory.

<Step 1>In the adjustment item selection screen, select [R]: Reset flash memory.-->The flash memory reset confirmation screen appears.

-->The [Reconfirm flash memory reset] screen then appears.

Flash memory reset (EVR)

< Attention >When the MAIN PWB ASSY has been replaced, always resetthe flash memory before making any other adjustments.Only reset the flash memory when the MAIN PWB ASSYhas been replaced. If the flash memory is reset when theMAIN PWB ASSY has not been replaced, all the adjusted datareverts to the default settings. In this event, adjust all thesettings. (Excludes firmware downloading.)

Enter [RESET] from the PC keyboard.

<Fig. 4-8-1>

52


Flash memory reset (EVR)

< Attention >When the MAIN PWB ASSY has been replaced, always resetthe flash memory before making any other adjustments.Only reset the flash memory when the MAIN PWB ASSYhas been replaced. If the flash memory is reset when theMAIN PWB ASSY has not been replaced, all the adjusted datareverts to the default settings. In this event, adjust all thesettings. (Excludes firmware downloading.)

Enter [RESET] from the PC keyboard.

R E S E T

Input is completed.Press the "Enter" key to reset the flash memory.

<Fig. 4-8-2>

Flash Memory Reset is completed

(1) Remove the DC jack cable from the camera.(2) Press the [Enter] key.

<Fig. 4-8-3>

<Step 2>

-->Once the flash memory reset has been completed successfully, the [End flash memory reset] screen appears.

<Step 3>

53


4-9. [F9] : AF-Assist Light AdjustmentAF-Assist light Adjustment is required when the AF FRAME ASSY is removed.

Preparation for AF-Assist Light adjustment(1) Output the image to TV with a camera that works normally.(2) Apply the sign according to the mark of the center of the AF target [+].(3) Remove Cabinet R, and tighten one screw.

Setup for AF-Assist Light adjustment

TV Center

Lighting image

1mm

Monitor TV Picture

932mm±2mm

Line chart

Fluorescent light stand

Camera

Center

3

54


<Step 1>Select [F9] from the [Adjustment Items Select Screen (Fig. 4-7-5)]. (press [F9] on the PC keyboard)---> The [AF-Assist light adjustment Preparation Screen (Fig. 4-9-1)] appears.

<Step 2>When preparations are complete, press the Enter key.---> The [AF-Assist light adjustment Preparation Screen (Fig.4-9-2)] appears.

<Caution>When adjusting the camera, measure distance from the front face of the camera lens.

<Step 3>When preparations are complete, press the Enter key.

AF-Assist Light Adjustment

(1) Place the Line chart at a distance of 932+-2mm from thefront face of the lens.

Line chart

932 +-2mm<--------------------------------------Center-------------------------------------->

CAMERA < Setup for AF-Assist Light Adjustment >

<Fig. 4-9-2>


(1) Prepare it in the state that the power enterswith cabinet R removed.

(2) Set the Line chart.(3) Set the camera on a X-Y stage or tripod.(4) Ensure that the luminance of the surface of

the Line chart is between 9.0EV and 12.0EV.

When preparations (1) - (4) are complete, press the [Enter] key.--> The lens is extended when the [Enter] key is pressed.

<Fig. 4-9-1>

55


---> The [AF-Assist light adjustment Screen (Fig. 4-9-3)] appears.

Adjust the adjustment screw in the camera so that the irradiation standard of the AF-assist light may enter in aspecified area.

<Step 4>When preparations are complete, press the Enter key.---> The [AF-Assist light adjustment complete Screen (Fig. 4-9-4)] appears.

<Step 5>Press the Enter key while in the [AF-Assist light adjustment Complete Screen (Fig. 4-9-4)].---> The system returns to the [Adjustment Items Select Screen (Fig. 4-7-5)].


(1) Darken the lighting of the chart.(2) Adjust the position of the camera so that the center of

the Line chart is displayed in the center of TV.(3) Adjust the adjustment screw in the camera so that the

irradiation standard of the AF-Assist Light may enterin a specified area.

When adjustment is complete, press the [Enter] key on the PC.

<Fig. 4-9-3>

AF-Assist Light Adjustment completed.

Press the [Enter] key to return to theAdjustment Items Select screen.

<Fig. 4-9-4>

56


CAMERA Adjustment

< CAMERA Adjustment Preparations >

(1) Prepare the LB140 filter.(2) Adjust the color temperature of the pattern box (PTB450)

to 6100+-50K.(3) Adjust the luminance of the pattern box (PTB450)(4) Fix the camera on a tripod and set it in front of the

pattern box.

When preparations (1)-(4) are complete,press the [Enter] key on the PC.--> The lens is extended when the [Enter] key is pressed.

<Fig. 4-10-1>

4-10. [F5] : CAMERA Adjustment(shutter adjustment, adjustment for reduced aperture sensitivity, ISO sensitivity adjustment, white balanceadjustment, AE adjustment, offset level adjustment)

<Setup for Camera Adjustment>

<Step 1>Select [F5] CAMERA Adjustment on the [Adjustment Items Select] screen.—> The [CAMERA Adjustment Preparation] screen appears.


<Note>An error will occur during CAMERA adjustment, and adjustment cannot be completed, unless the pattern box is calibratedcorrectly.

—> The [Shutter Adjustment] screen appears.

Cam

era

Filter (LB140)

Pattern box

Maximum 5mm

Centerline

Maximum50mm

Maximum 60mm

57


Squeezing sensitivity decrease rate adjustment(1) Set the distance between the camera and pattern box.(2) Place the LB140 filter in front of the lens.

When preparations are complete, press the [Enter] key.LB140 filter

| ------------------------------| | | || 5mm or | 50mm or less. || less. | |<--Center--> | <------ Center ------> Pattern box |

(PTB450) |CAMERA |

| | ------------------------------

< Setup for CAMERA Adjustment ><Fig. 4-10-3>

Shutter adjustment(1) Set the distance between the camera and pattern box.(2) The LB140 filter is not placed in front of the lens.


------------------------------| | || 5mm or | 50mm or less. || less. | |<--Center--> | <------ Center ------> Pattern box |

(PTB450) |CAMERA |

| | ------------------------------


<Step 3>

—> The [Squeezing sensitivity decrease rate adjustment] screen appears.

<Step 4>

—> The [WB adjustment without filter] screen appears.

58


Camera adjustment is completed.Press the [Enter] key to returnto the Adjustment Item Selection Screen.

<Fig. 4-10-5>

WB adjustment without filter(1) Set the distance between the camera and pattern box.(2) Remove the LB140 filter from front of the lens.


------------------------------| <------------> <---------------------> | || 5mm or | 50mm or less. || less. | |<--Center--> | <------ Center ------> Pattern box |

(PTB450) |CAMERA |

| | ------------------------------


<Step 5>

—> Write the adjustment data to the flash ROM when adjustment has been completed correctly.—> The [CAMERA Adjustment Complete] screen appears.

<Step 6>

59


CCD Defect collection

< CCD Defect Correction Preparations >

(1) Adjust the color temperature of the pattern box(PTB450) to 6100+-50K.

(2) Adjust the luminance of the pattern box(PTB450) to 160+-5cd/m2.

(3) Fix the camera on a tripod and set it in frontof the pattern box.

When preparations (1) - (3) are complete, press the [Enter] key on the PC.

--> The lens is extended when press the [Enter] key.

<Fig. 4-11-1>

4-11. [F4] : CCD Defect Correction< Setup for CCD defect correction Adjustment>

<Step 1>Select [F4] CCD Defect Correction on the [Adjustment Items Select] screen.—> The [CCD Defect Correction Preparation] screen appears.


—> The [CCD Defect Correction Adjustment Start] screen appears.

Cam

era

Pattern boxCenterline

Maximum 30mm

60


CCD Defect CorrectionAdjust the distance between the camera and pattern box.

When preparations are complete, press the [Enter] key.

------------------------------| <--------------------> | || 30mm or less || |

Pattern box |(PTB450) |

CAMERA || | ------------------------------

< Setup for CCD Defect Correction Adjustment >

<Fig. 4-11-2>

CCD Defect Correction is completed.Press the [Enter] key to returnto the Adjustment Item Selection Screen.

<Fig. 4-11-3>

<Step 3>—> Write the adjustment data to the flash ROM when adjustment has been completed correctly.

—> The [CCD Defect Data Input Complete] screen appears.

<Step 4>

61


AF Adjustment

< AF Adjustment Preparations >

(1) Prepare a 1560mm and 865mm conversion lens.(2) Prepare a AF chart.(3) Mount the camera on a tripod.


--> The lens is extended when the [Enter] key is pressed.

<Fig. 4-12-1>

4-12. [F6] : AF Adjustment<Backlash adjustment/zoom reset adjustment/AF adjustment>

Run the adjustment in accordance with the instructions on the screen.

<Caution>(1) When adjusting the camera, measure distance from the front face of the camera lens.(2) After replacing the LENS CONST or MAIN PWB ASSY, always run AF adjustment after camera adjustment.(3) Do not conect VIDEO cable while adjusting AF.

<Step 1>Select [F6] AF Adjustment on the [Adjustment Items] screen.

--> The [AF Adjustment Preparation] screen appears.

<Step 2>When preparations are complete, press the Enter key.--> The [AF Adjustment Start] screen appears.

Lens Holder

Lens Base Plate

Lens Stand

Attention when conversion lens is used.

Convex side : Subject side.

Plane : Camera lens side.

900mm±2mm

A

AF chart

Fluorescent light stand

Camera

Center

Conversion lens

Conversion lens Distance A1560.69mm 25.16mm865.12mm 30.64mm

62



--> The [AF 2000mm Adjustment] screen appears.


--> The [AF 900mm Adjustment Start] screen appears.

AF Adjustment(1) Place the AF chart at a distance of 900+-5mm from the

front face of the zoom lens.(2) Place the 865.12mm conversion lens at a distance

of 30.64+-1mm from the front face of the lens.(3) Adjust the position of the camera so that the center of

the AF chart is displayed in the camera LCD.


AF chart30.64 +-1mm|<-> 900 +-2mm<---------------------------------------Center--------------------------------------->

---Conversion lensCAMERA |

< Setup for AF Adjustment ><Fig. 4-12-2>

AF-2000mm Adjustment(1) Place the AF chart at a distance of 900+-5mm from the

front face of the zoom lens.(2) Place the 1560.68mm conversion lens at a distance

of 25.16+-1mm from the front face of the lens.(3) Adjust the position of the camera so that the center of

the AF chart is displayed in the camera LCD.


AF chart25.16 +-1mm|<-> 900 +-2mm<---------------------------------------Center--------------------------------------->

---Conversion lensCAMERA |

< Setup for AF Adjustment ><Fig. 4-12-3>

63


<Fig. 4-12-5>

The AF adjustment is completed.

Press the [Enter] key to return to theAdjustment Items Select Screen.

AF-900mm Adjustment

(1) Remove the conversion lens.

(2) Adjust the position of the camera so that the center ofthe AF chart is displayed in the camera LCD.

When preparations (1) - (2) are complete, press the [Enter] key.

AF chart

900 +-2mm<--------------------------------------Center-------------------------------------->

CAMERA | < Setup for AF Adjustment >

<Fig. 4-12-4>


--> Adjustment proceeds to backlash adjustment, zoom reset adjustment, and AF adjustment, and the [AF AdjustmentComplete] screen appears.

<Step 6>Press the Enter key.

--> The system returns to the [Adjustment Items Select] screen.AF adjustment is now complete.

64


4-13. [F1] : Battery Voltage Adjustment<Setup for Flash Adjustment>(1) When adjusting the battery voltage, supply power (5V) to the camera from the [Power Cable Jig] before setting the jig

mode.(2) Always measure input voltage in the vicinity of the DC IN terminal.(3) When reducing the voltage, adjust the requrated power supply to ensure that the voltage is not reduced excessively from

the measured point. The adjustment software may produce an error if communication between the adjustment softwareand the camera is disrupted. Restart the adjustment software in this case.

<Step 1>Select [F1] Battery Voltage Adjustment on the [Adjustment Items Select] screen.—> The [Battery Voltage Adjustment Preparation] screen appears.

Power Cable Jig

–

+

FinePix S5100/S5500

USB cable

65


Battery Voltage Adjustment

(1) Supply 4.34V (+0.02V/-0.00V).When preparations are complete, press the [Enter] key.

<Fig. 4-13-2>

Battery Voltage Adjustment<Preparations>

1. Check that the Power Cable Jig and the camera are connected.*If not, return to the Jig Mode Setup screen,and connect the Power Cable Jig and the camera.

2. Supply power (5.0V) to the camera from the[Power Cable Jig].

When preparations are complete, press the [Enter] key on the PC.---> Lens is extended when the [Enter] key is pressed.

<Fig. 4-13-1>


—> The [4.34V Input] screen appears.

<Step 3>

66


<Fig. 4-13-4>


(1) Supply 4.34V (+0.02V/-0.00V).When preparations are complete, press the [Enter] key.Result= 6A

(2) Supply 3.94V (+0.02V/-0.00V).When preparations are complete, press the [Enter] key.Result= 63

(3) Supply 5.00V (+-0.05V).When preparations are complete, press the [Enter] key.

<Fig. 4-13-3>


(1) Supply 4.34V (+0.02V/-0.00V).When preparations are complete, press the [Enter] key.Result= 6A

(2) Supply 3.94V (+0.02V/-0.00V).When preparations are complete, press the [Enter] key.

<Step 4>


<Step 5>

—> Write the adjustment data to the Flash ROM when adjustment has been completed correctly.—> The [Battery Voltage Adjustment Complete] screen appears.

67


<Fig. 4-13-5>

The BATTERY adjustment is completed.

Press the [Enter] key to return to theAdjustment Item selection Screen.

<Step 6>

68


Flash Adjustment

< Preparations >

(1) Prepare a gray chart (1000mm x 1000mm or more).(2) Mount the camera on a tripod.(3) Put the gray chart from the front side of the flash

on the place of 1000mm+/-10mm.

When preparations (1) - (3) are complete, press the [Enter] key.---> Lens is extended when the [Enter] key is pressed.

<Fig. 4-14-1>

4-14. [F7] : Flash Adjustment<Setup for Flash Adjustment>(1) As flash adjustment is readily affected by external light, ensure that the vicinity of the gray chart is very dark.(2) Ensure that distance is measured from the front of the camera during flash adjustment.(3) When adjusting the flash, always ensure that AF adjustment is complete before beginning flash adjustment.

Setup for Flash AdjustmentGray chart

1000±10mm

Centerline

<Step 1>Select [F7] Flash Adjustment on the [Adjustment Items Select] screen.--> The [Flash Adjustment Preparation] screen appears.


--> The [Flash Adjustment Start] screen appears.

Cam

era

69


<Step 3>

--> Write the adjustment data to the flash ROM when adjustment has been completed correctly.--> The [Flash Adjustment Complete] screen appears.

<Step 4>

Flash Adjustment(1) Adjust brightness so that the periphery of the gray chart

is as dark as possible.(2) Adjust the camera so that the entire chart is

shown on the LCD monitor.(3) Press the flash pop-up button.

When preparations (1) and (3) are complete,press the [Enter] key.

|<-------------------------------------------------------->| 1000 +-10mm|

<---------------------Center--------------------->

CAMERA

< Setup for Flash Adjustment ><Fig. 4-14-2>

Flash adjustment is completed.

Press the [Enter] key to return to the

Adjustment Item Selection Screen.

<Fig. 4-14-3>

70


4-15. [F11] : Video Adjustment<Setup for Video Adjustment>(1) Set up the PCI-2746C board in the computer as explained in the instructions for the video adjustment jig.(2) If the waveform of the brightness signal (Y) or color signal (C) does not appear in the “WAVE No. 0” window during

adjustments, check the connections of the video adjustment jig.

<Step 1>Select [F11] Video Adjustment on the [Adjustment Items Select] screen.—> The [Video Adjustment Preparation] screen appears.

FinePix S5100/S5500

PCI-2746C

Board

AC

100 ~ 240V

71


Video adjustment was completed.

1. Disconnect Video cable from camera.2. Close the [WaAVE No.0] window by close button.

Press the [Enter] key to return to theAdjustment Item selection Screen.

<Fig. 4-15-2>

VIDEO Adjustment

< VIDEO Adjustment Preparations >

(1) Connect the camera and video adj. jig with the video cable.(2) Confirm Video jig is connected with the video cable.

When preparations are complete,press the [Enter] key.

<Fig. 4-15-1>

<Fig. 4-15-3>


—> Write the adjustment data to the Flash ROM when adjustment has been completed correctly.—> The [VIDEO Adjustment Complete] screen appears.

<Step 3>

72


4-16. [F8] : Firmware DownloadAttention : When the download of the firmware is needed, FUJI SERVICE BULLETIN is contacted from

FTYO/QA. Till then, disregard this item.

<Setup for Firmware Download>

<Step 1>Select [F8] Firmware Download on the [Adjustment Items Select] screen.—> The [Firmware Download Start] screen appears.

to USB Connector

to DC JACK

FinePix S5100/S5500

73


Firmware download is completed

(1) Remove the Power Cable Jig from the camera.(2) Turn off power switch.(3) Reconnect Power Cable Jig.(4) Turn on the power switch while pressing the shutter button.(5) Press the [Enter] key after green LED lights on.

The system returns to the Jig Mode Setup screenwhen press the [Enter] key.

<Fig. 4-16-2>

Firmware DownloadLED lights to orange while downloading the firmware.Do not turn off the power while downloading the firmware.

c:\FinePixS5100_5500_W\Firm_1_28\SU580RSC1_28.bin

Press the ENTER Key to start download.

<Fig. 4-16-1>


—> The [Download Complete] screen appears if download is successful.

<Step 3>

74


4-17. [F12] : End Setting(Destination setting, USB ID write, Product mode setting)

1. The End setting consist of the following settings.* Destination setting* USB ID write* Product mode setting (mass storage identification)

2. The setting must always be run when the adjustment software is terminated. Failure to run Terminal Setting will preventidentification as Mass Storage when the camera is connected to the PC.

3. USB ID write details1) USB ID write requires that the USB device (in this case FinePix S5100/S5500) be unique throughout the world. For thisreason, each device has a unique ID as determined by the USB standard. If multiple devices with the same USB ID areconnected to a single PC, the PC will be unable to identify each USB device, thus preventing operation.

Item DetailsRepair Date Date information is acquired from the PC and written.Administrator ID C(43)Repair Station U.S. 61(a) SAPPORO 30(0)

Canada 62(b) SENDAI 31(1)Hawaii 63(c) TOKYO 33(3)Taiwan 64(d) NAGOYA 34(4)England 66(f) OSAKA 35(5)Germany 67(g) HIROSHIMA 37(7)France 68(h) FUKUOKA 38(8)Spain 69(i)Italy 6A(j)Netherlands 6B(k)Belgium 6C(l)Sweden 6D(m)Switzerland 6E(n)Norway 6F(o)Finland 70(p)Singapore 71(q)China 74(t)Ohter 7A(z)

Repair Serial No. A serial No. is assigned automatically and written

75


Destination settingThe destination is selected from an undermentioned list,according to third character from left side of the serial number.

The third character

 FinePix S5100 US/CA-model A to H,J,K<C> FinePix S5500 EU/EG/GE/AS-model L to N,P to V

<Fig. 4-17-2>

End Setting

The End settings consist of the destination setting,the USB_ID write, and product mode settings(= Mass Storage recognition).

Press the [Enter] key.

<Fig. 4-17-1>

<Step 1>Select [F12] End Setting on the [Adjustment Items Select] screen.—> The [End Setting Description] screen appears.


—> The [Destination Setting] screen appears.

<Step 3>

<Note>This example assumes that US-Model has been selected. The following screen therefore appears.—> The [US-Model selected] screen appears.

76


Destination settingThe destination is selected from an undermentioned list,according to third character from left side of the serial number.

The third character

 FinePix S5100 US/CA-model A to H,J,K<C> FinePix S5500 EU/EG/GE/AS-model L to N,P to V

Selected FinePix S5100 US/CA-model.Press the [Enter] key!

<Fig. 4-17-3>

Repair site ID input menuThe repair site is selected from an undermentioned list.

<A> SAPPORO SS <M> BRITAIN SENDAI SS <N> GERMANY<C> TOKYO SS <O> FRANCE<D> NAGOYA SS SPAIN<E> OSAKA SS <Q> ITALY<F> HIROSHIMA SS <R> NETHERLANDS<G> FUKUOKA SS <S> BELGIUM<H> USA <T> SWEDEN CANADA SWITZERLAND<J> HAWAII <V> NORWAY<K> TAIWAN <W> FINLAND

<X> SINGAPORE<L> CHINA <Z> OTHERS

<Fig. 4-17-4>

<Step 4>

—> The [USB ID Writing] screen appears.

<Step 5>

<Note>This example assumes that <H>USA has been selected. The following screen therefore appears.—> The [USA_ID USA] screen appears.

77


<Step 6>

—> The [FinePix S5100/S5500 Adjustment End] screen appears.

<Step 7>

USB ID

Selected USA.

Press the [Enter] key!

<Fig. 4-17-5>

<Fig. 4-17-6>

FinePix S5100/5500 Adjustment completed.

1)Remove USB cable from the camera.

2)Press the [Enter] key.

--> The adjustment software returns to the Jig mode setup screenafter press the [Enter] key.

78

5. Inspection FinePix S5100/S5500 Service Manual

5. Inspection5-1. Required Measuring Equipment

Measuring equipment RemarksPower supply AC adapter (AC-5V), Regurated power supplyDigital voltmeter For general useAmmeter For general use (able to measure 1mA or less)Power Cable Jig Common with adjustment JIG (ZJ00840-100)xD-Picture card For general useMacro Chart Resolution confirmation (ZJ00525-100)TV Monitor NTSC, TV monitor, minimum resolution 600 lines

5-2. Connection of Measuring EquipmentPower Cable Jig.The output current of the Regurated power supply must not become 2.5A or more.

FinePix S5100/S5500

79

5. InspectionFinePix S5100/S5500 Service Manual

5-3. Inspection and Factory SettingsSequemnce Item Mode Preparations for adjustment

(measurement points, subject, other)Method of adjustment

(VRs, waveforms, required values)Measuring

equipment and jigsMeasurement points

(VRs, positions)1

2

3

4

5

6

7

8

9

10

Check appearance

Power supplyswitch

Check LCD

Check Moviemode shock noise

Check macrophotographyCheck focus

Movie recordingcheck

Movie play backcheck

Resolutionconfirmation

BATT cover detectcheckDelete modecheck

Autophotography

LCD_ON

Autophotography

AutophotographyLCD_ON

AutophotographyLCD_ON

MoviephotographyLCD_ON

Playback

Playback

PlaybackLCD_ONDelete

Visual check of camera

(1) Place BATTERY in camera

(2) Insert xD-Picture card andclose cover

(3) Turn on the power SW

(4) If the date set messageappears, press Back

(1) Press DISP/BACK button(2) Press DISP/BACK button

(3) Press DISP/BACK button(4) Press DISP/BACK button(1) Apply an appropriate

shock to the camera.* Do not apply shock directly

to the lens or card cover.(1) Press Macro button

(2) Match the Black-Edged ofMACRO CHART to a fullangle of view of LCD

(3) Press shutter button totake photographs

(1) Select Movie mode(2) Half-press shutter button

-> full-press -> full-press-> half-press -> release

(3) Half-press five secondslater -> release

(1) Select Playback mode(2) Press ‘Down’ key to

playback movie(1) Confirm the resolution of

the image recorded by “5”(2) Connect the TV monitoring

(1) Open card cover to checkrecording

(1) Select <Delete all frames>from the menu, and pressthe <OK> button

(2) Press the <OK> buttonagain

No dents exterior of camera.No problem with click actionof switches.No dust or fogging of LCDwindow.(1) Applied 4AA batteries or

equivalent jig may beused.

(2) Recording check card

(3) Power supply LED is greenand beeps

(4) Through screen and textdisplay in LCD.

(1) Framing guide is displayed(2) Framing guide disappears(3) The LCD display

disappears(4) LCD is displayed(1) No problem with display on

LCD monitor.Restoration possibledespite disruption of sync.

(1) Macro icon appears inLCD monitor

(3) LED beside viewfinderchanges from green toorange (recording) togreen

(1) Standby display on LCD(2) Movie recording begins.

Recording displayed onLCD.

(3) Movie recordingcompleted. Recording onxD-Picture card

(2) Movie played back on LCDmonitor

(1) Played back on LCDmonitor.

(2) Standard (Horizontalresolution)

NTSC Center area : 350Circumferential area : 300

PAL Center area : 300Circumferential area : 250

(3) Thing of four even points(1) Switch power OFF

(1) [OK to delete all frames?]displayed

(2) Movie/photography screenextinguished

MACROCHART

LCD monitor

LCD monitorTV monitor

LCD monitor

LCD monitor

80

5. Inspection FinePix S5100/S5500 Service Manual

Sequemnce Item Mode Preparations for adjustment(measurement points, subject, other)

Method of adjustment(VRs, waveforms, required values)

Measuringequipment and jigs

Measurement points(VRs, positions)

11

12

13

Battery low check

Currentconsumptioncheck

Factory setting

Factory settingwhen updatingpackaging

MovieLCD_ON

MoviephotographyLCD_ON

Playback

(1) Connect Power Cable Jig

(2) Set voltage(3) Turn on the Power SW(4) Set to pre-end voltage(5) Set to end voltage

(1) Connect Power Cable Jig(2) Set voltage(3) Turn on the Power SW(4) Press the <LCD> button to

switch the LCD monitorON

(5) After the through screen isdisplayed, check currentconsumption

(1) Return all settings to initialvaluesIMAGE DISP: ONPower saving: 2 MINFORMAT: OKFRAME NO.: CONT.Beep: CENTERSHUTTER: CENTERDate/Time: Not setTime DIFF.: Not setLCD: ONUSB MODE: Card ReaderSTART-IMAGE OFFLANG.: ENGLISHVIDEO(US/CA): NTSC(EU/EG/GE/AS):PALCCD-RAW: OFFSelf Timer: OFFMode Dial: AUTOWhite Balance: AUTO

(2) Inspection battery/inspection xD-Picture cardnot inserted in camera

(3) Battery cover closed(4) LCD surface free of

contamination(5) Clean exterior of camera(1) No damage to exterior

when checking (6) of 13items

(2) Update packaging inaccordance with parts listdisplay

Refer to Battery Adjustmentfor connection details(2) Set voltage to 5.0 ± 0.5V(3) Starts normally(4) Set voltage 4.34 ± 0.2V(5) Set voltage to 3.94 ± 0.2V.

Lens retracts and mainpower switched OFF

(2) Set voltage to 5.0 ± 0.05V(3) Starts normally

(5) Maximum currentconsumption 450mA

* Setting and clearing date(1) Connect the USB cable

from the PC to the camera(ensure that the PC isswitched ON)

(2) Open the card cover andswitch power ON(POWER_ON) whilepressing the shutter button

(3) Switch power OFF(POWER_OFF)

(4) Check that the date hasbeen cleared

PowerCable Jig

Reguratedpowersupply

PowerCable Jig

Ammeter

81

6. Parts ListFinePix S5100/S5500 Service Manual

6. Parts List6-1. Packing and Accessories6-1-1. US-model (FinePix S5100)

Ref No. Parts No. Description Comment EL Ref No. Parts No. Description Comment EL

A101

A102

A103

A104

A105

A106

A107

A108

A109

A110

A111

A112

A120

A116

A117/

A117B

A118

A119

A121

A122

A114A115

A113

A101 FZ05983-200 UNITARY BOX WU S5100 NA102 FZ05328-100 SHEET MOLD NA103 BB13000-100 PARTITION PAD WU S5100 NA104 BB12943-100 BAR CODE LABEL BLANK NA105 AZF0000-311 HDPE BAG NO.11 N

A106 FZ04793-100 ALKALINE BATTERY =A107 FZ04741-100 VIDEO CABLE NA108 FZ05365-100 USB CABLE NA109 BU02939-100 SHOULDER BELT ASSY NA110 BU02876-100 LENS CAP ASSY N

A111 BU03097-100 LENS HOOD ASSY NA112 AZF0000-101 LDPE BAG NO.10 NA113 BB18002-100 CERTIFICATION SEAL NA114 BF04146-100 XDCARD 16MB ASSY =A115 BL00209-100 CASE_XD-CARD for XD CARD N

A116 FZ05352-500 CD-ROM SX4.2G NA117 BB18294-100 DEST.LBL.5800US J FG NA117B BB18294-A00 DEST.LBL.5800US C FGA118 BL00372-100 IMPORTANT SAFETY NA119 BL00373-100 US WARRANTY NA120 BL00416-200 MANUAL (ENG) N

A121 BL00417-200 QUICK MANUAL (ENG) NA122 BL00417-500 QUICK MANUAL (SPA) N

Revised: 25. Nov. 2005

* Use A117B for the camera that uses M223B.

82

6. Parts List FinePix S5100/S5500 Service Manual

6-1-2. CA-model (FinePix S5100)


A101

A102

A103

A104

A105

A106

A107

A108

A109

A110

A111

A112

A119

A116

A120

A121

A118

A114A115

A113

A117/

A117B

A101 FZ05983-200 UNITARY BOX WU S5100 NA102 FZ05328-100 SHEET MOLD NA103 BB13000-100 PARTITION PAD WU S5100 NA104 BB12943-100 BAR CODE LABEL BLANK NA105 AZF0000-311 HDPE BAG NO.11 N




A116 FZ05352-500 CD-ROM SX4.2G NA117 BB18294-400 DEST.LBL.5800CA J FG NA117B BB18294-D00 DEST.LBL.5800CA C FGA118 BL00416-200 MANUAL (ENG) NA119 BL00416-300 MANUAL (FRE) NA120 BL00417-200 QUICK MANUAL (ENG) N

A121 BL00417-300 QUICK MANUAL (FRE) N


83


6-1-3. EU-model (FinePix S5500)


A101

A102

A103

A104

A105

A106

A107

A108

A109

A110

A111

A112

A119

A116

A123

A124

A118

A114A115

A113

A121

A122

A120 A117/

A117B

A101 FZ05990-100 UNITARY BOX WE S5500 NA102 FZ05328-100 SHEET MOLD NA103 FZ05998-100 PARTITION PAD WE S5500 NA104 BB12943-100 BAR CODE LABEL BLANK NA105 AZF0000-311 HDPE BAG NO.11 N


A111 BU03097-100 LENS HOOD ASSY NA112 AZF0000-111 BAG PLASTIC NO.11 NA113 BB18002-100 CERTIFICATION SEAL NA114 BF04146-100 XDCARD 16MB ASSY =A115 BL00209-100 CASE_XD-CARD for XD CARD N

A116 FZ05352-500 CD-ROM SX4.2G NA117 BB18294-200 DEST.LBL.5800EU J FG NA117B BB18294-B00 DEST.LBL.5800EU C FGA118 BL00416-200 MANUAL (ENG) NA119 BL00416-300 MANUAL (FRE) NA120 BL00416-400 MANUAL (GER) N

A121 BL00417-200 QUICK MANUAL (ENG) NA122 BL00417-300 QUICK MANUAL (FRE) NA123 BL00417-400 QUICK MANUAL (GER) NA124 BL00417-500 QUICK MANUAL (SPA) N



84


6-1-4. EG-model (FinePix S5500)

Ref No. Parts No. Description Comment EL

A101

A102

A103

A104

A105

A106

A107

A108

A109

A110

A111

A112

A119

A116

A118

A120

A114A115

A113

A117/

A117B




A116 FZ05352-500 CD-ROM SX4.2G NA117 BB18294-300 DEST.LBL.5800EG J FG NA117B BB18294-C00 DEST.LBL.5800EG C FGA118 BL00176-100 WARRANTY CARD EG NA119 BL00416-200 MANUAL (ENG) NA120 BL00417-200 QUICK MANUAL (ENG) N



85


6-1-5. GE-model (FinePix S5500)


A101

A102

A103

A104

A105

A106

A107

A108

A109

A110

A111

A112

A119

A116

A118

A114A115

A113

A117/

A117B




A116 FZ05352-500 CD-ROM SX4.2G NA117 BB18294-500 DEST.LBL.5800GE J FG NA117B BB18294-E00 DEST.LBL.5800GE C FGA118 BL00416-400 MANUAL (GER) NA119 BL00417-400 QUICK MANUAL (GER) N



86


6-1-6. AS-model (FinePix S5500)


A101

A102

A103

A104

A105

A106

A107

A108

A109

A110

A111

A112

A119

A116

A118

A114A115

A113

A117/

A117B




A116 FZ05352-500 CD-ROM SX4.2G NA117 BB18294-600 DEST.LBL.5800AS J FG NA117B BB18294-F00 DEST.LBL.5800AS C FGA118 BL00416-200 MANUAL (ENG) NA119 BL00417-200 QUICK MANUAL (ENG) N



87


6-1-7. CH-model (FinePix S5500)

A101

A102

A103

A104

A105A106

A107

A108

A109

A110

A111

A112

A116

A113

A114A115


Revised: 17. Jan. 2005

A101 FZ05990-300 UNITARY BOX CH S5500 CH-model NA102 FZ05328-100 SHEET MOLD NA103 FZ05998-100 PARTITION PAD WE S5500 NA104 BB06392-100 LABEL PLAIN 2 NA105 AZF0000-311 HDPE BAG NO.11 N


A111 BU03097-100 LENS HOOD ASSY NA112 AZF0000-101 LDPE BAG NO.10 NA113 BL00416-600 MANUAL (CHI) NA114 BF04146-100 XDCARD 16MB ASSY =A115 BL00209-100 CASE_XD-CARD for XD CARD N

A116 FZ05352-500 CD-ROM SX4.2G N

88


6-2. Cabi Front block6-2-1. US/CA-model (FinePix S5100)


B

C

DA

E

A

F

M201

M202

M203

M204

M206

M207 M208

M209

M210

M211

M212

M213

M214

M215

M216

M217

M218

M219

M220

M221M222

M223/

M223B

M224

M205

M225

M226

M201 BU03093-100 CABI FRONT ASSY ABS NM202 BB16384-100 CI BADGE NM203 BB18101-100 CCD BADGE NM204 BB16809-100 JACK COVER NM205 BB13148-100 BL SCREW N

M206 FZ04998-100 MIC ASSY NM207 FZ04224-100 SPEAKER ASSY NM208 BB16856-100 SP SHEET NM209 FZ05547-100 AF FRAME ASSY NM210 BB16693-100 ADJUSTMENT SPRING N

M211 BB16695-100 ADJUSTMENT SCREW NM212 BU03094-101 STROBE CONST WU S5100 =M213 FZ05545-100 FSW PWB ASSY NM214 FZ05436-100 FFC NM215 BU03148-100 ST PWB ASSY =

M216 FZ05978-100 LIGHT Xe tube NM217 BB16362-200 ST TOP WU S5100 NM218 BB16365-100 STROBE COVER NM219 ATG1725-0ND SCREW_BT_2P_M1.7*5.0_N_D NM220 ATG1724-0NN SCREW_BT_2P_M1.7X4.0_N_N N

M221 BB16367-100 ST-BUTTON NM222 BB16398-100 ST-BUTTON CSP NM223 BB18103-300 PRODUCT LABEL WU S5100 NM223B BB18103-600 PRODUCT LABEL WU(FC) S5100M224 BB16931-100 SCREW M1.7X5.5 NM225 BB16356-100 RELEASE BUTTON N

M226 BB16396-100 RELEASE CSP N

Revised: 25. Nov. 2005 Revised: 17. Jan. 2005


89



B

C

DA

E

A

F

M201

M202

M203

M204

M206

M207 M208

M209

M210

M211

M212

M213

M214

M215

M216

M217

M218

M219

M220

M221M222

M223/

M223B

M224

M205

M225

M226

6-2-2. EU/EG/GE/AS-model (FinePix S5500)



M211 BB16695-100 ADJUSTMENT SCREW NM212 BU03094-201 STROBE CONST WE S5500 =M213 FZ05545-100 FSW PWB ASSY NM214 FZ05436-100 FFC NM215 BU03148-100 ST PWB ASSY =

M216 FZ05978-100 LIGHT Xe tube NM217 BB16362-300 ST TOP WE S5500 NM218 BB16365-100 STROBE COVER NM219 ATG1725-0ND SCREW_BT_2P_M1.7*5.0_N_D NM220 ATG1724-0NN SCREW_BT_2P_M1.7X4.0_N_N N

M221 BB16367-100 ST-BUTTON NM222 BB16398-100 ST-BUTTON CSP NM223 BB18103-200 PRODUCT LABEL WE S5500 NM223B BB18103-500 PRODUCT LABEL WE(FC) S5500M224 BB16931-100 SCREW M1.7X5.5 NM225 BB16356-100 RELEASE BUTTON N


Revised: 25. Nov. 2005 Revised: 17. Jan. 2005


90


6-2-3. CH-model (FinePix S5500)


Revised: 17. Jan. 2005

B

C

DA

E

A

F

M201

M202

M203

M204

M206

M207 M208

M209

M210

M211

M212

M213

M214

M215

M216

M217

M218

M219

M220

M221M222

M223

M224

M205

M225

M226



M211 BB16695-100 ADJUSTMENT SCREW NM212 BU03094-201 STROBE CONST WE S5500 =M213 FZ05545-100 FSW PWB ASSY NM214 FZ05436-100 FFC NM215 BU03148-100 ST PWB ASSY =

M216 FZ05978-100 LIGHT Xe tube NM217 BB16362-300 ST TOP WE S5500 NM218 BB16365-100 STROBE COVER NM219 ATG1725-0ND SCREW_BT_2P_M1.7*5.0_N_D NM220 ATG1724-0NN SCREW_BT_2P_M1.7X4.0_N_N N

M221 BB16367-100 ST-BUTTON NM222 BB16398-100 ST-BUTTON CSP NM223 BB18103-400 PRODUCT LABEL CH S5500 NM224 BB16931-100 SCREW M1.7X5.5 NM225 BB16356-100 RELEASE BUTTON N


91



M301 BU03095-100 BATTERY HOLDER ASSY NM302 BB16403-100 CONTACT PSP A NM303 BB16404-100 CONTACT PSP B NM304 BB16405-100 CONTACT PSP C NM305 BB18109-100 BATTERY LID N

M306 BB16385-100 TERMINAL PLATE A NM307 BB16386-100 TERMINAL PLATE B NM308 BB16406-100 TERMINAL PSP NM309 BB16933-100 SCREW BT2P1.4X2.5N NM310 BB16412-100 BATTERY SHAFT N

M311 BB16934-100 ISORATION PIECE NM312 BU02946-200 BATT HARNESS ASSY NM313 FZ05433-100 FFC NM314 CB1456-A300 RSW PWB ASSY NM315 BF05179-100 LENS CONST =

M316 BB16388-100 LCD FRAME NM317 CB1454-A100 MAIN PWB ASSY =M318 BB15553-100 CONDENSER SHEET NM319 CB1455-A100 DCST PWB ASSY NM320 BB16743-100 INSURATION TUBE N

M321 BB12548-200 SP SCREW M1.7X2.5 NM322 BF05333-100 LCD ASSY NM323 BB18108-100 BATTERY HOLDER NM324 FZ06090-100 EVF EMI SHEET =M325 BB18459-100 CCD EMI SHEET N

M326 BB16951-100 MF SHEET2 NM327 BB17079-100 JC SHEET NM328 BB18121-100 MAIN FRAME NM329 BU03084-100 EVF UNIT CONST NM330 FZ05551-100 EMI SHEET A =

M331 FZ05435-100 FFC NM332 ATG1728-0ND SCREW_BT_2P_M1.7*8.0_N_D N

K TAPE 1 *ZS00024-100 (polyimide tape PIT- 652S) is cut in 19X15mm and it uses it.

G

H

IE

B

KC

J

J

G

HI

D

F

L

M

L

K

M301M302

M303

M304

M305

M306

M307

M308

M308

M309

M310

M311

M312

M313

M314

M315

M326

M328

M325

M332

M332

M332M330

M319

M320

M321

M316

M322

M317

M329

M331

M332

M321

M318

M327

M323

M324K TAPE 1

6-3. Inner block

92



M

M401

M404

M405

M405

M405

M405

M406

M407

M408

M409

M410

M411M412

M413

M414

M415

M417 M416

M418

M402

M403

M401 CB1456-A100 KSW PWB ASSY NM402 BB16414-100 BLIND SHEET NM403 BB16935-100 L SHEET NM404 CB1456-A200 MSW PWB ASSY ABS NM405 ATG1724-0ND SCREW_BT_2P_M1.7*4.0_N_D N

M406 FZ05434-100 FFC NM407 BU03096-100 CABI REAR ASSY NM408 BB16374-100 CARD COVER NM409 BB16413-100 CARD COVER SHAFT NM410 BB18122-100 ZOOM KEY N

M411 BB18115-100 OPERATION BUTTON NM412 BB18116-100 F BUTTON NM413 BB16740-100 LCD CUSHION NM414 BB16832-100 W FACE(LCD COVER) NM415 BB13149-200 SCREW N

M416 BB16745-100 LCD COVER NM417 BB13148-100 BL SCREW NM418 BB09250-200 PL SEAL (U) N

6-4. Cabi Rear block

93


6-5. Electrical parts

[NOTE]

The components indicated by mark are critical for safety.When indicated parts by reference number, please includethe board name.


* Due to standardization, replacement in the parts list may be different fromthe parts list specified in the circuit or the components used on the set.

DCST PWB ASSY

[BATTERY]BT301 FZ04705-101 BATTERY BackUp =

[CONNECTOR]CN501 FGA113-0021 CONNECTOR CJ 2P RN 1.5MM PH NCN502 FZ05344-100 JACK USB MINI-B NCN503 FGC143-0701 CONNECTOR CJ 70P BN 0.5MM RV NCN601 FGA058-0021 CONNECTOR CJ 2P RN1.25MM PN NCN602 FGA137-0042 CONNECTOR LJ 4P RB 2.0MM PH NCN651 FGB046-0201 CONNECTOR CJ 20P FN0.5MM NH NJ501 FZ04171-100 JACK N

[FUSE]F502 FP00039-253 FUSE 2.5A 32V UL NF503 FP00039-253 FUSE 2.5A 32V UL NF504 FP00039-253 FUSE 2.5A 32V UL NF505 FP00039-203 FUSE 2A 32V UL NF506 FP00039-153 FUSE 1.5A 32V UL NF507 FP00039-103 FUSE 1A 32V UL N

RSW PWB ASSY

[CONNECTOR]

CN951 FGB139-0081 CONNECTOR CJ 8P FN0.5MM NH N

[SWITCH]SW951 FZ04993-100 TACT SWITCH NSW952 FZ04725-100 DETECTOR SWITCH NSW953 FZ04725-100 DETECTOR SWITCH N

MAIN PWB ASSY

[SWITCH]SW201 FZ01045-100 DETECTOR SWITCH N

[CONNECTOR]CN101 FGB089-0291 CONNECTOR CJ 29P FN0.3MM NH NCN11 FGA129-0021 CONNECTOR CJ 2P SN1MM RH NCN201 FGC125-0701 CONNECTOR CJ 70P BN 0.5MM PV NCN202 FGY067-0201 CONNECTOR CJ 20P B 1MM NN NCN203 FGB156-0081 CONNECTOR CJ 8P FN 0.5MM NV NCN204 FGB139-0081 CONNECTOR CJ 8P FN 0.5MM NH NCN205 FGB046-0141 CONNECTOR CJ 14P FN0.5MM NH NCN206 FGB139-0061 CONNECTOR CJ 6P FN0.5MM NH NCN401 FGA096-0021 CONNECTOR CJ 2P RN 1.0MM PH NCN404 FGB046-0241 CONNECTOR CJ 24P FN0.5MM NH NCN405 FGB156-0181 CONNECTOR CJ 18P FN 0.5MM NV NJ51 FZ04722-100 JACK AV JACK N

MSW PWB ASSY

[SWITCH]SW851 FZ02084-100 TACT SWITCH NSW852 FZ02084-100 TACT SWITCH N

[CONNECTOR]CN851 FGB061-0081 CONNECTOR CJ 8P N 0.5MM V N

KSW PWB ASSY

[SWITCH]SW801 FZ02630-100 TACT SWITCH NSW802 FZ02630-100 TACT SWITCH NSW803 FZ02084-100 TACT SWITCH NSW804 FZ02630-100 TACT SWITCH NSW805 FZ02084-100 TACT SWITCH NSW806 FZ02084-100 TACT SWITCH NSW807 FZ02084-100 TACT SWITCH NSW808 FZ02084-100 TACT SWITCH NSW809 FZ02084-100 TACT SWITCH NSW810 FZ02084-100 TACT SWITCH NSW811 FZ02084-100 TACT SWITCH N

[CONNECTOR]CN801 FGB046-0141 CONNECTOR CJ 4P FN 0.5MM NH NCN802 FGB060-0081 CONNECTOR CJ 8P FN 0.5MM NH N

94

7. Appendix FinePix S5100/S5500 Service Manual

7. Appendix7-1. Function of display for Firmware Version

The function to display the version is installed in FinePixS5100.The version the camera equipped with of the firmware can bedisplayed only by operating the main body of the camera.

[Procedure]1. The camera is made a play mode.

2. The power supply switch is turned on while pressingthe shutter button.

3. The "SETUP" display is selected, and changes to aDATE/TIME set mode.

4. The DATE/TIME setting is matched as follows(Fig. 7-1).

• 2040 . 2. 29

• 11 : 59 PM

5. After the date is set, keeps pressing the shutter buttonfor three seconds or more.

6. The version of the farmware is displayed in the upperright of LCD only while the shutter button is being done(Fig. 7-2).

Example of display: 1.28

* It is shown that the version of the farm-ware is 1.28.

<Fig. 7-1>

<Fig. 7-2>

Version

1.28

95

7. AppendixFinePix S5100/S5500 Service Manual

7-2. List of Related Technical Updates IssuedTo ensure that after-sales srevice is performed accuratety, keep a record here of the technical updates issuedthat cover this device.

Technical Update No. Date Title Details/Other

2005-003 17. Jan. 2005 New parts additionCH-model addtion: P87, P90

Release button & Release csp: P88, P89

2005-094 25. Nov. 2005Service manual

Revised pages: P81 to P86 and P88 to P89revision

26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan.

FUJI PHOTO FILM CO., LTD.

finepix s5100, s5500 service manual

Documents