flameproof motors moteurs antidéflagrants ... · pdf fileflameproof motors moteurs...

Flameproof motorsMoteurs antidéflagrants

Explosionsgeschützte MotorenMotores antideflagrantes

Motori antideflagranti

63 ÷ 315

I I 2 G , I I 2 GD

Ex d, Ex de • IIB, IIC • tD • IP65 (A21)

Atav - Les Ateliers de l’Avre

is a Cemp trademark

Les Ateliers del’Avre

Flameproof motorsMoteurs antidéflagrants

Explosionsgeschützte MotorenMotores antideflagrantes

Motori antideflagranti

Catalogue 14 Catalogue 14 Katalog 14 Catálogo 14 Catalogo 14Edition 09-09 Edition 09-09 Die Auflage 09-09 Edición 09-09 Edizione 09-09Replaces 06-08 Remplace 06-08 Ersetzt die Auflage 06-08 Sustituye 06-08 Sostituisce 06-08

6 3 ÷ 3 1 5

I I 2 G , I I 2 GD

Ex d, Ex de • IIB, IIC • tD • IP65 (A21)

ENGLISH CONTENTSPage

0. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90.1 SI units and conversion equations . . . . . . . . . . . . . . . . . . . . . 90.2 Engineering formulae for motor drives . . . . . . . . . . . . . . . . . 100.3 Standards and specifications . . . . . . . . . . . . . . . . . . . . . . . . 110.4 Protection against explosions in dangerous areas . . . . . . . 121. General informations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201.1 Range of motors in the ATEX series . . . . . . . . . . . . . . . . . . . 201.2 Main characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211.3 Main options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221.4 Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232. Design features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242.1 Mounting arrangements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242.2 Installation and applications . . . . . . . . . . . . . . . . . . . . . . . . . 262.3 Materials, painting and nameplate . . . . . . . . . . . . . . . . . . . . 282.4 Shaft ends, balancing, vibrations,

noise level coupling and belt drives . . . . . . . . . . . . . . . . . . . 292.5 Bearing system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302.6 Terminal box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Page3. Electrical design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363.1 Standard operating conditions . . . . . . . . . . . . . . . . . . . . . . . 363.2 Efficiency and power factor at partial load . . . . . . . . . . . . . 383.3 Insulation and temperature rise . . . . . . . . . . . . . . . . . . . . . . 393.4 Duty types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403.5 Connecting diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423.6 Protection devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453.7 Frequency converter driven motors . . . . . . . . . . . . . . . . . . 464. Performance data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2074.1 Three-phase motors, 1 speed . . . . . . . . . . . . . . . . . . . . . . 2084.2 Three-phase motors, 2 speeds,

for general purpose (constant torque) . . . . . . . . . . . . . . . . 2164.3 Three-phase motors, 2 speeds,

for centrifugal machines (quadratic torque) . . . . . . . . . . . . 2244.4 Single-phase motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2324.5 Motors energized by inverter . . . . . . . . . . . . . . . . . . . . . . . 2345. Overall dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2456. Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251

FRANÇAIS SOMMAIREPage

0. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490.1 Unités de mesure du SI et équivalences . . . . . . . . . . . . . . . 490.2 Formules d'usage commun . . . . . . . . . . . . . . . . . . . . . . . . . 500.3 Normes et spécifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 510.4 Protection contre les explosions dans

les zones dangereuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 521. Informations générales . . . . . . . . . . . . . . . . . . . . . . . . . . . 601.1 Gamme de moteurs de la série ATEX . . . . . . . . . . . . . . . . . 601.2 Caractéristiques principales . . . . . . . . . . . . . . . . . . . . . . . . . 611.3 Options principales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 621.4 Identification de la référence commerciale . . . . . . . . . . . . . 632. Caractéristiques mécaniques . . . . . . . . . . . . . . . . . . . . . . 642.1 Formes de construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 642.2 Installation et applications . . . . . . . . . . . . . . . . . . . . . . . . . . 662.3 Matériaux, peinture et plaque signalétique . . . . . . . . . . . . . 682.4 Bout d'arbre, équilibrage, vibrations,

bruit et accouplement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 692.5 Roulements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 702.6 Boîte à bornes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Page3. Caractéristiques électriques . . . . . . . . . . . . . . . . . . . . . . . 763.1 Conditions nominales d'exploitation . . . . . . . . . . . . . . . . . . 763.2 Rendement et facteur de puissance

à différentes charges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 783.3 Isolation et température d'échauffement . . . . . . . . . . . . . . . 793.4 Différents régimes d'utilisation . . . . . . . . . . . . . . . . . . . . . . . 803.5 Schémas de branchement . . . . . . . . . . . . . . . . . . . . . . . . . . 823.6 Systèmes de protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 853.7 Moteurs alimentés par un variateur

électronique de fréquence . . . . . . . . . . . . . . . . . . . . . . . . . 864. Données nominales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2074.1 Moteurs triphasés, 1 vitesse . . . . . . . . . . . . . . . . . . . . . . . . 2084.2 Moteurs triphasés, 2 vitesses,

pour usage général (couple constant) . . . . . . . . . . . . . . . . 2164.3 Moteurs triphasés, 2 vitesses,

pour machines centrifuges (couple quadratique) . . . . . . . . 2244.4 Moteurs monophasés . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2324.5 Moteurs alimentés par variateur . . . . . . . . . . . . . . . . . . . . . 2345. Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2456. Pièces détachées . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251

DEUTSCH INHALTSVERZEICHNISSeite

0. Einleitung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 890.1 SI-Maßeinheiten und Umrechnungen . . . . . . . . . . . . . . . . . 890.2 Formeln aus der Antriebstechnik . . . . . . . . . . . . . . . . . . . . . 900.3 Normen und Spezifikationen . . . . . . . . . . . . . . . . . . . . . . . . 910.4 Explosionsschutz in den Gefahrenzonen . . . . . . . . . . . . . . . 921. Allgemeine Informationen . . . . . . . . . . . . . . . . . . . . . . . . 1001.1 Produktpalette der Motoren der Serie ATEX . . . . . . . . . . . 1001.2 Hauptmerkmale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1011.3 Hauptausführungen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1021.4 Bedeutung der Kürzel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1032. Mechanische Eigenschaften . . . . . . . . . . . . . . . . . . . . . . 1042.1 Bauformen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1042.2 Installation und Anwendungen . . . . . . . . . . . . . . . . . . . . . . 1062.3 Material, Lackierung und Typenschild . . . . . . . . . . . . . . . . 1082.4 Wellenenden, Auswuchtung, Schwingungen,

Geräuschpegel und Kupplung . . . . . . . . . . . . . . . . . . . . . . 1092.5 Lager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1102.6 Klemmkasten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Seite3. Elektrische Eigenschaften . . . . . . . . . . . . . . . . . . . . . . . . 1163.1 Nennbetriebsbedingungen . . . . . . . . . . . . . . . . . . . . . . . . . 1163.2 Wirkungsgrad und Leistungsfaktor bei Teillast . . . . . . . . . 1183.3 Isolierung und Übertemperatur . . . . . . . . . . . . . . . . . . . . . 1193.4 Betriebsarten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1203.5 Schaltung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1223.6 Schutzvorrichtungen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1253.7 Motoren für Antrieb durch elektronischen

Frequenzwandler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1264. Betriebsdaten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2074.1 Drehstrom Motoren, 1 Drehzahl . . . . . . . . . . . . . . . . . . . . . 2084.2 Drehstrom Motoren, 2 Drehzahlen, für allgemeinen

Gebrauch (konstantes Gegenmoment) . . . . . . . . . . . . . . . 2164.3 Drehstrom Motoren, 2 Drehzahlen, für

Zentrifugalmaschinen (quadratisches Gegenmoment) . . . 2244.4 Einphasen Motoren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2324.5 Motoren mit Umrichterversorgung . . . . . . . . . . . . . . . . . . . 2345. Abmessungen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2456. Ersatzteilliste . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251

7

ENGLISH

Flameproof motors

9

ENGLISH

0. Introduction0.1 SI units and conversion equations

Table 0 A

Description SI Conversion equations

Formular symbols Unit symbol Unit name

DistanceAreaVolume

LAV

mm2

m3

metre

1 m3 = 1000 dm3

1 dm3 = 1l

Angle in one plane α, β, γ rad radian 1° = π rad180

1' = 1°/601" = 1'/60

TimeFrequency

tf

sHz

secondHertz

1 Hz = 1/s

SpeedVelocityAngular velocity

nvω

1/minm/srad/s

1 km/h = 1 m/s3.6

AccelerationAngular acceleration

aα

m/s2rad/s2

MassDensity

mρ

kgkg/m3

kilogram

Force

PressureMechanical stress

Fpσ

N

Pa = N/m2

N/mm2

Newton

Pascal

1N = 1kg · 1 m/s29.81 N = 1 kp9.81 · 104 N/m2 = 1kp/cm2

9.81 N/mm2 = 1 kp/mm2

Work doneEnergyThermal quantity

WWQ

J = Nm Joule 9.81 Nm = 1 kpm4187 J = 1 kcal1 kWh = 3.6 x 106 J

Torque M Nm 9.81 Nm = 1 kpm1 Nm = 0.102 kpm

Power P W = J/s = Nm/s Watt 735.5 W = 1 hp

Moment of inertia J kg m2 9.81 kg m2 = 1 kpms2PD2 = 4 J

Dynamic viscosityKinematic viscosity

ην

Pa · sm2/s

10 ¯ 1 Pa · s = 1 P (Poise)10 ¯ 4 m2/s = 1 St (Stoke)

Electric currentElectric voltageElectric resistanceElectric conductivityElectric capacityCharge

IURGCQ

AVΩSFC

AmpereVoltOhmSiemensFaradayCoulomb

1 A = 1 W/V = 1 V/Ω1 V = 1 W/A1 Ω = 1 V/A = 1/S1 S = 1/Ω1 F = 1 C/V1 C = 1 A · s

InductanceMagnetic flux densityMagnetic field strengthMagnetic flux

LBHΦ

HTA/mWb

HenryTesla

Weber

1 H = 1 Vs/A1 T = 1 Wb/m2

1 Wb = 1 V · s

Temperature difference Tϑ

K°C

Kelvin 0 K = - 273.15 °C

0.1 SI units and conversion equations

10

ENGLISH

0.2 Engineering formulae for motor drives

0.2 Engineering formulae for motor drives

Power (3-phase motors)

P1 = power input =

U · I · cos ϕ · CD3 · 10-3 [kW]P2 = power output = P1 · η [kW]

Where:U = voltage [ V ]I = current [ I ]cos ϕ = power factorη = efficiency

Power requirements of someapplications

Lifting:

P = m · v · 9.81 · 10-3 [kW]η

Rotation:

P = M · n [kW]9550 · η

Fan and pump drives:

P = H · Q [W]η

Where:P = power [kW]m = mass [kg]v = speed [m/s]n = rotational speed [min-1]η = efficiencyM = torque [Nm]Q = output [m3/s]H = head [N/m2]

Torque from motor power

M = 9550 · P2 [Nm]n

Where:P2 = motor output [kW]n = motor speed

Conversion of torque for step-up andstep-down speed ratios:

M2 =M1 · n1n2

Where:n1 = motor speed [min-1]M1 = motor torque at n1 [Nm]n2 = speed of load [min-1]M2 = torque of load at n2 [Nm]

Moment of Inertia J

Moment of Inertia of a cylindrical flywheel:

J = md28

Where:m = mass [kg]d = flywheel diameter [m]

Effective moment of inertia on the motorof a linearly moved load:

J = 91.2 · m · ( v )2n

Where:m = mass [kg]v = velocity [m/s]n = motor speed [min-1]

Conversions of moments of inertia forstep-up or step-down speed ratio:

J2= J

1· ( n1 )2n

2

Where:n1 = motor speedJ1 = moment of inertia at n1n2 = speed of loadJ2 = moment of inertia of load

Factor of Inertia FI

FI = Jmot + JloadJmot

Where:Jmot = moment of inertia of motorJoad = moment of inertia of load

Starting time ta

ta =FI · Jmot · n [s]

9.55 · ( Mmot - Mload )

Where:FI = Factor of inertiaJmot = moment of inertia of motor [kgm2]n = motor speed [min-1]Mmot = motor torque

during starting (mean) [Nm]Mload = counter torque of load

during starting (mean) [Nm]

SpeedThe no-load speed is virtually the same asthe synchronous speed. The synchronousspeed of the motor is calculated as follow:

ns = 120 · f/p [min-1]

Where:

f = frequency [Hz]p = number of pole

The synchronous speed is reduced by theslip (S) to the rated speed:

nn = ns · (1-S) [min-1]

11

ENGLISH

0.3 Standards and specifications

0.3 Standards and specifications

Flameproof motors conform to the followingstandards and specifications:

Table 0 B

INTERNATIONAL EU

Title IEC CENELEC

Electrical rotating machines/ratedoperation and characteristic data

IEC 60034-1 EN 60034-1

Methods for determining losses and efficiencyof rotating electrical machines

IEC 60034-2 EN 60034-2

Protection types rotating electrical machines IEC 60034-5 EN 60034-5

Cooling methods of rotating electricalmachines

IEC 60034-6 EN 60034-6

Construction types of rotating electricalmachines

IEC 60034-7 EN 60034-7

Terminal markings and direction of rotationfor electrical machines

IEC 60034-8 HD 53 8

Noise emission, limit values IEC 60034-9 EN 60034-9

Start-up behaviour of squirrel-cage motors at50 Hz up to 660V

IEC 60034-12 EN 60034-12

Vibration severity of rotating electrical machines IEC 60034-14 EN 60034-14

Protection level provided by enclosures forelectrical equipment against mechanical impact(Code IK)

IEC 60068-1IEC 60068-2-75

EN 50102

Fixing dimensions and outputs for IM B3 IEC 60072 EN 50347

Fixing dimensions and outputs for IM B5,IM B14

IEC 60072 EN 50347

Cylindrical shaft ends for electrical machines IEC 60072 EN 60072

Electrical equipment for hazardous areasGeneral provisions

IEC 60079-0 EN 60079-0

Electrical equipment for hazardous areasFlame-proof enclosure “d”

IEC 60079-1 EN 60079-1

Electrical equipment for hazardous areasIncreased safety “e”

IEC 60079-7 EN 60079-7

Electrical equipment for use in areas withpresence of combustible dustGeneral provisions

IEC 61241-0 EN 61241-0

Electrical equipment for use in areas withpresence of combustible dustProtection method “tD”

IEC 61241-1 EN 61241-1

12

ENGLISH

0.4 Protection against explosions in dangerous areas0.4.1 Types protection

0.4.1 Types protection

The use of electrical apparatus inpotentially explosive atmospheres is quiteusual today.This equipment has to be manufactured insuch a way that there is no risk ofexplosion.An explosion occurs when the threefollowing conditions happen:

• presence of a potentially explosiveatmosphere;

• possibility of transmission of theexplosion;

• existence of an ignition source.

The recognized types of protectioneliminate one of these conditions and thusmake an explosion impossible.

Two types of protection prevent thepresence of a potentially explosiveatmosphere inside the electricalapparatus:

• oil immersion (safety “o”);

• pressurized apparatus (safety “p”).

Two types of protection make thetransmission of an internal explosion to thepotentially explosive atmospheresurrounding the electrical apparatusimpossible:

• sand filling (safety “q”);

• flameproof enclosure (safety “d”).

Lastly, three types of protection eliminateany source of ignition such as sparks,overheating, etc...:

• increased safety (safety “e”);

• intrinsic safety (safety “i”);

• protection “n” (restricted to zone 2).

In practice, only four of these seven typesof protection are applicable to electricmotors:

• pressurized apparatus (symbol Ex p);

• flameproof enclosure (symbol Ex d);

• increased safety (symbol Ex e);

• non sparking protection (symbol Ex n).

Electric motors have an additional type ofprotection (symbol Ex de) which is acombination of:

- flameproof enclosure “d” for motorframe;

- increased safety “e” for terminalbox.

Fig. 0 A - Specific marking for protectionagainst explosions - Directive 94/9/EC.

13

ENGLISH

Table 0 C - Dangerous areas classified into zones

Usage areain the presence of

GAS

Usage areain the presence of

COMBUSTIBLE DUSTS

Hazardous levelof the operational

ZONE

Zone 0 Zone 20Explosive atmosphereALWAYS PRESENT

Zone 1 Zone 21PROBABLE

explosive atmosphere

Zone 2 Zone 22Explosive atmosphere

UNLIKELY

Dangerous areas include any area in whichexplosive atmospheres may occur underspecific conditions.

An explosive atmosphere is a mixture of airand combustible gases, vapours, fumes ordust under atmospheric conditions wherecombustion expands itself (explosion) afterignition.Only local authorities can classify hazardousareas.

The user shall classify the hazardous areasas indicated in the European directive1999/92/EC under his own responsibility.

International standards IEC 61241-10provide instructions on how to classify thehazardous areas in relation to the chemicalnature, to the physical characteristics and tothe amount of substances used and basedon the frequency and period of time inwhich an explosive mix may develop.

Zones susceptible to gas

When the hazard is due to the presence ofgas, vapours or mists of flammablesubstances, the European directive1999/92/EC envisages a classification inthree zones defined as followos:

Zone 0 - Areas constantly susceptible to anexplosive atmosphere, or for long periods oftime. Power equipment with doubleinsulation must be installed in this area.

Zone 1 - Areas where an explosiveatmosphere is likely to develop duringnormal conditions.Flameproof electric motors or motors withadded protection means can be installed inthis zone (for the latter, restrictions by thestandards apply).

Zone 2 - Areas rarely susceptible to anexplosive atmosphere and for a short periodof time.Flameproof motors or motors with addedprotection can be installed in this zone, aswell as non-sparking motors.

Zones susceptible to combustible dust

When the hazard is due to the presence ofcombustible dust, the European directive1999/92/EC envisages a classification inthree zones defined as followos:

Zone 20 - Areas constantly susceptible toan explosive atmosphere, or for longperiods of time.Power apparatus cannot be installed in thiszone.

Zone 21 - Areas where an explosiveatmosphere is likely to develop duringnormal conditions.Electric motors certified in compliance withthe ATEX directive with IP6X protectionrating can be installed in this zone

Zone 22 - Areas rarely susceptible to anexplosive atmosphere, and only for a shortperiod of time. In the presence ofconductive dust, electric motors certified incompliance with the ATEX directive withprotection rating IP6x can be installed in thiszone, whereas in the presence of nonconductive dust, motors with protectionrating IP5x and a declaration of conformityissued by the manufacturer can be installed.

Fig. 0 B - Warning sign for areas subjectto the risk of explosion -Directive 99/92/EC

0.40.4.2 Dangerous areas and zones

0.4.2 Dangerous areas and zones

14

ENGLISH

0.40.4.3 Apparatus classification0.4.4 Enclosure groups

The ATEX 94/9/EC European Directiveclassifies equipment into three categories,with differing protection levels, related to theprotection guaranteed.

Table 0 D - Equipment categories

NOTE: Equipment of higher categoriescan also be installed instead of those of alower category.

PROTECTIONLEVEL

guaranteed bythe equipmentCategory

MINE SURFACE

CategoryGAS

Category

COMBUSTIBLEDUSTCategory

Very high M1 1G 1D

High M2 2G 2D

Normal not provided for 3G 3D

0.4.4 Enclosure groups

The standards classify electrical equipmentinto two groups.

Group I: electric apparatus to be installed inmines or galleries susceptible to firedamp orcoal dust.

Group II: electric apparatus to be installedin surface plants susceptible to other explo-sive atmospheres.

The enclosures for equipment intended foruse on the surface, providing “d” protection(flameproof), are in turn broken down intothree sub-groups, in relation to theinflammable substances for which they aresuitable:Group IIA, Group IIB, Group IIC.

A motor that belongs to a certain enclosuregroup is also suitable for lower enclosuregroups: a motor in group IIB is also suitablefor group IIA; a motor in group IIC is alsosuitable for group IIA and IIB.

0.4.3 Apparatus classification

15

ENGLISH

0.40.4.5 Temperature classes (for gas atmospheres)

0.4.5 Temperature classes (for gas atmospheres)

The electrical apparatus is classified into 6classes according to the maximum surfacetemperatures.

The maximum surface temperature is thehighest temperature which is attained inservice under the conditions described inthe standards, by any part of the electricalapparatus, which, could ignite thesurrounding atmosphere.

For electric motors this is:• the temperature of the outside surface ofthe enclosure for “d” and “p” protectionmodes;

• the temperature of any internal or externalpoint for type of protection “e” or “n”.

Table 0 E

Ignition temperatureof medium relativeto limit temperature

Temperatureclass

Maximum surface temperature ofelectrical equipment including 40 °Cambient temperature

[°C] [°C] [°F]

over 450 T 1 450 842

from 300 to 450 T 2 300 572

from 200 to 300 T 3 200 392

from 135 to 200 T 4 135 275

from 100 to 135 T 5 100 212

from 85 to 100 T 6 85 185

16

ENGLISH

Combustible gases and vapours are dividedinto classes according to their ignitiontemperature and into groups according totheir explosive capacity.

Markings on motors and other electricalequipment with the symbols used to indicatethe protection mode, the enclosure group,and the temperature class, indicate the zonein which such equipment can be installed.

0.40.4.6 Combustion temperatures of gases, vapours and groups

0.4.6 Combustion temperatures of gases, vapours and groups

Table 0 F - Classification of the more common combustible gases and vapours according to temperature class and group

* depending on composition

GroupTemperature classes

T 1 T 2 T 3 T 4 T 5 T 6

I Methane (firedamp)

IIA Acetic acidAcetoneAmmoniaBenzoleBenzeneButanoneCarbon monoxideEthaneEthyl acetateEthyl ChlorideMethaneMethanolMethyl acetateMethyl alcoholMethyl ChlorideNaphtalenePropaneTolueneXylene

Acetic anhydrideI amyl acetaten butanen butyl alcoholAmylic alcoholButyl acetateCyclohexanonEthyl alcoholIso butylic alcoholLiquefied gasNatural gasPropyl acetate

CyclohexaneCyclohexanolDecaneDiesel fuelsGasolineHeating oilHeptaneHexaneJet fuelsPentanePetroleum*

AcetaldehydeEther

IIB Coke-oven gasWater gas(carburetted)

1,3- butadieneEthyleneEthylbenzeneEthylene oxide

Hydrogen sulphideIsoprenePetroleum*

Ethyl ether

IIC Hydrogen Acetylene Carbon disulphideEthyl nitrate

17

ENGLISH

0.40.4.7 Temperature for atmospheres with combustible dusts

The flash point of the dust must be takeninto account in providing protection againstflammable dust, both where this is in cloudform and in layers.

The surface temperature of the enclosureindicated on the motor nameplate must beless than the reference ignition temperature.

SourceSIRALtd

0.4.7 Temperature for atmospheres with combustible dusts

The reference temperature is the lowestbetween the two values thus calculated:

TS1 = 2/3 Tcl (Tcl = ignition temperature ofthe cloud of dust)TS2 = T5mm – 75K (T5mm = ignitiontemperature of a 5mm layer of dust).Tamm = lowest between TS1 and TS2.

Table 0 G - Calculation of the flash points for combustible dusts

Dustignition temperature

CloudTcl

LayerT5mm

Safety temperature Ts1 = 2/3 Tcl Ts2 = T5mm - 75K

Maximum surfacetemperature

Tamm = lowest between Ts1 and Ts2

Surface temperature of the motor m Tamm

Table 0 H - Examples of flash points for combustible dusts

Cloud[°C]

Layer[°C]

Aluminium 590 >450

Carbon dust 380 225

Flour 490 340

Wheat dust 510 300

Methylcellulose 420 320

Phenolic resin 530 >450

Polyethylene 420 melting

PVC 700 >450

Soot 810 570

Starch 460 435

Sugar 490 460

18

ENGLISH

0.40.4.8 Choice of safety-electric motor

0.4.8 Choice of safety-electric motor

The connection between danger zones andthe categories of equipment to be used isdefined in Directive 1999/92/EC.

The specific construction standards for theprotection modes (e.g. Ex d) also define themotor category that can be obtained byapplying the standards (e.g. 2G).

N. B. Equipment of a higher category can beinstalled in place of equipment of a lowercategory

Table 0 I - Choosing the protection mode for zones in which gas is present

Explosive Atmosphere Danger Zone Protection guaranteedby Equipment

Motor Category Protection Mode

ALWAYS PRESENT 0 Very High 1G IEC EN 60079-26

PROBABLE 1 High 2GEx dEx deEx e

IMPROBABLE 2 Normal 3G Ex nA

Table 0 L - Choice of protection mode for areas where combustible dust is present

Explosive Atmosphere Danger Zone Protection guaranteedby Equipment

Motor Category Protection Mode

ALWAYS PRESENT 20 Very High 1D Currently not provided for

PROBABLE 21 High 2D Ex tD - A21 - IP6x

IMPROBABLE22

Conductive dustsNormal 2D Ex tD - A21 - IP6x

IMPROBABLE22

Non-conductive dustsNormal 3D Ex tD - A22 - IP5x

19

ENGLISH

0.40.4.9 Certification and approved laboratories

0.4.9 Certification and approved laboratories

The motors offered in the catalogue hereincomply with Directive 94/9/EC ATEX, whichstates that two different certificates ofconformity are to be issued:• EC Type examination certificate• Product quality assurance notification.

Certification

Flameproof motors and motors with addedprotection must be approved by a notifiedbody appointed by the EuropeanCommission according to the methodsdefined by the same ATEX directive.

The motors are classified based on thehazardous atmosphere of the place ofinstallation.

The type of motor protection must bechosen on the basis of the area ofinstallation.The dangerousness of the zone isdetermined by the atmosphere involved.

The user is responsible for determining thetype of protection, enclosure group, andmaximum surface temperature of the motorto be installed.

The user must also correctly install, connectto the mains, use and service the motor.Certificates of conformity to CENELECstandards are valid in all member countriesin the European Union and membercountries of CENELEC.

The electro-technical committees of thefollowing countries are members of theCENELEC: Austria, Belgium, Denmark,Finland, France, Germany, Greece, Ireland,Italy, Luxembourg, Norway, Holland,Portugal, United Kingdom, Spain, Swedenand Switzerland.

The nominal characteristics of motors relateto a maximum ambient temperature of40°C.

The certifications are valid for a maximumambient temperature of 60°C (IIC) and 80°C(IIB).

At ambient temperatures exceeding 40°C,the nominal characteristics may deviatefrom the standard.

Certificates of EC Type Conformity relate tomotors with:• IIB or IIC enclosure groups• Ex d or Ex de protection modes• category 2G and temperature classes T3,T4, T5, T6

• category 2GD and surface temperaturesT150°C, T135°C, T100°C, T85°C.

These certificates cover:• motors with voltage up to 1000V andfrequencies of 50 and 60Hz

• single-phase motors• three-phase double winding and/ordouble polarity motors

• motors installed at altitudes higher than1000m above sea level

• service from S1 to S9• motors operated by electronic frequencyconverter and with forced ventilation.

• accessories such as: anti-condensationheaters and temperature detectors

• ambient temperature:minimum - 50 °Cmaximum + 80 °C (T3)

+ 60 °C (T4).

Notified bodies

The list of notified bodies can be found onthe European Union website at the followingaddress:www.europa.eu.int/comm/enterprise/atex/nb/nblist.htm

IECEx Certifications

Presently (July 2009) the procedure forobtaining certifications according to theIECEx program is in place.

20

ENGLISH

The motors offered in this catalogue complywith standards concerning equipment andprotective systems intended for use inpotentially explosive atmospheres, incompliance with European Directive94/9/EC dated 23/3/94, otherwise known asthe ATEX directive.

The ATEX directive states that two differentcertificates of conformity are to be issued.

One is the “EC-Type examination certificate”for the homologation of the prototype andthe other is for the “Production QualityAssurance Notification”.

The Certificates are issued by CESI in Milan,Notified Body no. 0722.

All motors in the ATEX series are available in2G (for gas) or 2GD (for gas and dust)versions.

1. General informations1.1 Range of motors in the ATEX series

1.1 Range of motors in the ATEX series

Also available flameproof motors with brake and flameproof motors of Group I for installation in mines.Documentation supplied upon request.

Table 1 A - The Series ATEX range

Table 1 B - Temperature Class upon request

(*) For the single and three-phase, 2-speed motors: power lower than T4.

Version Framesize[mm]

Output range(2 pole)[kW]

Standardtemperatureclass for2G motors

Standardsurface

temperature for2GD motors

Motor type

Ex d IIB Ex de IIB Ex d IIC Ex de IIC

Single speed, three phase(2, 4, 6, 8 pole)

63 ÷ 315 0.18 ÷ 200.00 T4 T 135°C AB 30 AB 35 AC 30 AC 35

Two speeds, three phase(2/4, 4/8, 4/6, 6/8 pole)for general purpose(constant-torque)

63 ÷ 315 0.15 ÷ 160.00 T4 T 135°C AB 20 AB 25 AC 20 AC 25

Two speeds, three phase(2/4, 4/8, 4/6, 6/8 pole)for centrifugal machines(quadratic-torque)

63 ÷ 315 0.18 ÷ 160.00 T4 T 135°C AB 40 AB 45 AC 40 AC 45

Single phase,(2, 4, 6 pole)

63 ÷ 100 0.10 ÷ 3.00 T4 T 135°C AB 10 AB 15 AC 10 AC 15

Single-phase withcapacitor in extra-sizeterminal box(2, 4, 6 pole)

63 ÷ 100 0.10 ÷ 1.10 T4 T 135°C AB 12 AC 12

Motors energized byinverter(2, 4, 6, 8 poli)

63 ÷ 315 0.18 ÷ 200.00 T4 T 135°C AB 70 AB 75 AC 70 AC 75

Version T3 T5 T6

63 ÷ 160 Same power as T4 Same power as T4 (*) Power lower than T4

180 ÷ 315 Same power as T4 Power lower than T4 Power lower than T4

21

ENGLISH

1.2 Main characteristics

• Flameproof motors compliant with theStandards IEC EN 60079-0, 60079-1,60079-7 for atmospheres where gas ispresent and IEC EN 61241-0, 61241-1 forareas where combustible dust is present.

• Three phase and single phaseSquirrel Cage Asynchronous Inductionmotors.

• Totally enclosed, fan cooled, frame IP55with Terminal box IP65.

• The motors dimensions comply withIEC 60072 standard.

• Power Supply 400V / 50Hz.Three-phase, 1-speed motors, 2-4-6-8poles, T4 (for sizes between 63 and 250,multi-voltage power supply380-400-420V/ 50 Hz).

• Class F insulation.

• Noise level within 80 dB (A).

• Terminal Box:- available both in a flameproof, orincreased safety version

- large size- standard position - top, opposite feet- rotate by 90° in 4 positions.

• Motor frame and terminal box enclosureseparated to avoid the transmission ofexplosions.

• Winding cables connected to the terminalboard by means of terminal blocks or bya flameproof sealing device.

• Internal and external mechanicalcomponents painted with epoxy polyesterpowders;

- stainless steel nameplate,- anti-corrosion screws.

• Highly resistant to impact:- cast iron made frame, terminal box andendshields.

- fan cover in sheet steel.

• Low friction dust seals.

• The conformity certificates also coveralternatives, such as:

- altitude over 1000m- modification of the rated voltage andrated frequency

- power supply from an inverter- motor protection through temperaturedetectors

- duty S1 to S9.

1.2 Main characteristics

22

ENGLISH

1.3 Main options

1.3 Main options

Main versions

• Motors with brakes.

• 2GD motors for areas classified as zone21 and zone 22 (Combustible dusts).

• Group I motors (for mines).

Electrical variants

• Non-standard voltages and frequencies(maximum voltage 1000V).

• Motors for tropical climates.

• Motors for low temperatures (-50°C)

• Temperature rise below 80K.

• Motors insulated to class H.

• Motors with bimetallic detector,thermistor PTC or thermistor PT100.

• Motors with anti-condensation heaters.

• Motors with special electrical design.

• Single-phase motors with capacitorfitted in a large-size terminal box(Ex d, max 50 µF).

Mechanical variants

• Special flanges and shafts.

• Double ended shafts.

• Cable gland fitted to terminal box.

• Terminal box with special cable entries.

• Motors without terminal box and withloose cables. Sealing joints and conduitscan be supplied on request.

• Motors protection IP56 - IP65 - IP66.

• Motors with condensation drainagevalves.

• Motors with special bearings(uni-directional, with sensors, with rollers,insulated, oversized, thrust bearings).

• Grade A or B balancing

• Motors with a rain cap or sun shield,water-shedding disc.

• Side terminal box frame size 160 to 315.

• Separate terminal box for auxiliaryterminals.

• Low noise emission version.

• High protection against corrosion fortropical climates or applications in marineenvironments:

- external mechanical components finishedwith epoxy paint;

- protection of the internal parts (windingand rotor) with protective paint;

- stainless steel screws.

Accessories

• Motors suitable for frequency inverterdrive.

• Motors with encoder.

• Motors with forced ventilation (from framesize 100).

Certificates

• Motors according to American Bureau ofShipping, Bureau Veritas, Det NorskeVeritas, Germanischer LLoyd, KoreanRegister of Shipping, LLoyd Register ofShipping, Nippon Kaiji Kyokaj, R.I.Na., ...

23

ENGLISH

1.4 Nomenclature

A B 2 5 132 S 46 B5 3F 400/50 = Example of the commercial codes

1.4 Nomenclature

Pos. 1 = Motor series:

Pos. 2 = Type of application:

Pos. 3 = Type of motor (electric characteristics):

Pos. 4 = Terminal box version:

Pos. 5 = Size (centre height):

Pos. 6 = Length of stator pack:

* Three-phase, 2-speed version

Pos. 7 = Polarity:

Pos. 8 = Mounting (IM Code I):

Pos. 9 = Supply:

63 71 80 90 100 112 132 160 180 200 225 250 280 315* *

Extra short SAShort A A A S LA SB S MA LA S S SMedium M MB M MB M M MLong B B B L LB ML L L L L LB M M MExtra long L ML L

A Flameproof 63÷315

63 90 132 200 28071 100 160 225 31580 112 180 250

B3 V5 V6B5 V1 V3B14 V18 V19B35 V15 V36

3F xxxD / xxxS / xxThree-phase 1-speed; voltage for delta connection;voltage for star connection; frequency

3F xxx / xx Three-phase, 2-speed: voltage; frequency

1F xxx / xx Single-phase; voltage; frequency

2 2 poles 24 Double polarity: 2 / 4 poles 46 Double polarity: 4 / 6 poles



8 8 poles 43 Double polarity: 4 / 16 poles



0 Protection method Ex d 5 Protection method Ex e

3 Without box, with plate Ex d 2 Ex d capacitor holder in extra-size box

1 Single phase 4 Three-phase 2 speed quadratic torque

2 Three-phase 2 speed, constant torque 5 For lifting

3 Three-phase 1 speed 7 For inverters

B Enclosure group IIB

C Enclosure group IIC

24

ENGLISH

CEI 2-14 B3 V5IEC EN 60034-7 code I IM B3 IM V5IEC EN 60034-7 code II IM 1001 IM 1011

CEI 2-14 B3/B14 V5/V18IEC EN 60034-7 code I IM B34IEC EN 60034-7 code II IM 2101 IM 2111

CEI 2-14 B3/B5 V5/V1IEC EN 60034-7 code I IM B35 IM V15IEC EN 60034-7 code II IM 2001 IM 2011



2. Design features2.1 Mounting arrangements

2.1 Mounting arrangements

The most commonly used mountingarrangements are shown in the table 2 A.Other mounting arrangements areavailable on request.

Standard motors ordered in basicmounting arrangements (universalmounting arrangements)IM B3, IM B5 or IM B14 can also beoperated in the following differentmounting positions:- IM B3 in IM B6, IM B7, IM B8, IM V5 orIM V6,

- IM B5 in IM V1 or IM V3,- IM B14 in IM V18 or IM V19.

According to the safety standard forelectrical machines, foreign objects mustbe prevented from falling into the fancover.

Motors for vertical arrangement with shaftend down are fitted with a protective hoodover the fan cowl.

Table 2 A

Size 63 ÷ 315

Foot-mounted motor

Size 63 ÷ 315

Flange-mounted motor:large flange,clearance fixing holes

Size 63 ÷ 132

Flange-mounted motor:small flange,tapped fixing holes

Size 63 ÷ 315

Foot and flange-mounted motor:large flange, clearancefixing holes

Size 63 ÷ 132

Foot and flange-mounted motor:with small flange, tapped fixingholes

25

ENGLISH

2.1

V6/V19 B6/B14 B7/B14 B8/B14

IM 2131 IM 2151 IM 2161 IM 2171

V6/V3 B6/B5 B7/B5 B8/B5IM V36IM 2031 IM 2051 IM 2061 IM 2071

V19IM V19IM 3631

V3IM V3IM 3031

V6 B6 B7 B8IM V6 IM B6 IM B7 IM B8IM 1031 IM 1051 IM 1061 IM 1071

26

ENGLISH

2.2 Installation and application2.2.1 Installation, mechanical enclosure and cooling

Standard installation

The motors can be installed outdoors and industy, moist and chemically aggressiveenvironment (industrial climate) at ambienttemperatures from -20 °C to 40 °C.

Mechanical protection (IP); Table 2 B

The mechanical protection systems forelectric motors are classified with the IPcode followed by two numbers and, in someapplications, by a letter.

IP (International Protection):this indicates the level of protection againstaccidental contacts of foreign bodies andagainst water.

0 - 6 (1st digit):this indicates the level of protection againstaccidental contacts of foreign bodies.

0 - 8 (2nd digit):this indicates the level of protection againstwater.

W, S and M (additional letters for specialprotections):

W; this means that the machine is to beused in specified weather conditions andwith special protections.The W letter has to be added to the IP code(e. g. IPW55).

S and M; these are used for protectionagainst water.The letter S stands for static protection;protection against water only for astationary motor. Letter M stands forprotection against water when the motor isrunning (e. g. IP56S).

Without the additional letters the protectionapplies in both cases (standing still andrunning motor).

Our standard motors are IP55 (terminal boxIP65). On request we can supply motorswithout ventilation with IP56 or IP57, andself ventilated motors with IP56S.

Upper-Deck Installation

Motors meant for installation on board shipsand offshore areas are designed to complywith the specifications of therelevant classification authorities (see page22).

Gear mounting, Oil-protected Flange

In some applications, it is necessary that theflange and the drive shaft are completelysealed against oil. This need must bespecified during the order phase.

Fixed bearings

Some applications need to have a “zeroaxial play”. This need must be specifiedduring the order phase.

Cooling

Motors are air-cooled by means ofexternal surface ventilation (IC 411).Standard motors have radial flow fanallowing fully reversible rotation.Reference standards are: IEC 60034-6.From frame size 100 to 315 motors maybe supplied with forced ventilation.

2.2.1 Installation, mechanical enclosure and cooling

Table 2 B - Mechanical protection to IEC 60034-5

Protection against accidental contactand the penetration of foreign bodies

Internationalprotection

Protection against water

Complete protection against contact and approachingof voltage-carrying parts as well as against contactwith rotating parts inside the housing.Protection against harmful dust deposits.The penetration of dust is not completely preventedbut the dust cannot enter in such quantities as toaffect operation.

IP55standard design

A jet of water squirting out of a nozzle towardsthe motor from all directions has no harmful effect.

IP56special design

In case of temporary flood, e. g. heavy seas, watercannot enter into the motor in harmful quantities.

IP57special design

Motor can operate under water at given pressure.

Complete protection against contact of voltage-carryingparts as well against contact with rotating parts insidethe housing.Protection against the penetration of dust (dust-proof).

IP65special design

A jet of water squirting out of a nozzle towardsthe motor from all directions as no harmful effect.

27

ENGLISH

2.2.2 Low temperature version and anti-condensation heating

2.22.2.2 Low temperature version and anti-condensation heating

Low Temperature Version

Motors intended for use at extremely lowtemperatures are specially designed.

Flameproof certificates are valid fortemperatures as low as -50°C.

Motors equipped with heating coils keep theminimum temperature of a stopped motor at-20°C (see table 2 C).As an alternative to heaters, the motors canbe powered with low voltage via terminalsU1 and V1 (see table 2 C).

Also, it is possible to use a specialconstruction with suitable materials in lowtemperature areas (-50º C) as an alternativeto heating the motor.

Anti-condensation heating

Condensate may form inside the motor dueto temperature fluctuations.

To prevent this from happening, motorsmust be heated using strip type heaters onthe end windings or low voltage power canbe supplied to the winding via terminals U1and V1.

The heat output is given in table 2 C.

It is vital that during the motor operation theheaters are turned off.

The supply voltage for the heaters is 230V± 10% (115V ± 10% on request).

Table 2 C - Data of the anti-condensation heater

Framesize

For preventing condensationFor protection at temperaturesbelow -20 °C (down to -50 °C)

Withheater

Via Motor winding Withheater

Via Motor winding

Output Heating voltage with arated motor voltage of

Output Heating voltage with arated motor voltage of

Output[W]

[VA]230V[V]

400V[V]

440V[V]

500V[V]

690V[V]

Output[W] [VA]

230V[V]

400V[V]

440V[V]

500V[V]

690V[V]

63 25 35 45 75 90 100 130 50 90 70 120 140 160 210

71 25 55 35 65 75 85 110 50 130 60 100 120 135 175

80 25 70 30 55 65 75 100 50 180 50 90 100 115 155

90 25 100 25 45 50 60 80 50 250 40 70 80 95 125

100 25 140 20 35 40 50 65 50 440 40 65 75 85 115

112 50 190 20 38 45 50 65 100 490 35 60 70 80 105

132 50 300 20 35 40 45 60 100 700 30 55 65 70 90

160 50 420 17 30 35 40 50 100 950 25 45 55 60 80

180 100 500 15 25 30 35 45 200 1200 25 40 50 55 70

200 100 720 13 20 25 30 40 200 1500 20 35 40 45 60

225 100 800 13 20 25 30 40 200 2200 20 35 40 45 60

250 100 950 10 20 25 30 40 200 2700 20 35 40 45 60

280 200 1700 --- 20 22 25 30 400 3000 --- 28 35 40 50

315 200 1900 --- 16 20 25 30 400 3600 --- 25 32 38 48

315 L 200 2100 --- 14 18 24 30 400 4800 --- 22 30 35 45

0 7 2 2 C E S I 0 2 A T E X 1 2 2 n 0 0 0 0 0 1 y 0 4E l e c t r i c Mo t o r A B 3 0 1 6 0 L 4 3 ~I I 2 G E x d I I B T 4 I P 5 5

V A H z 1/m i n c o s ϕ kW4 0 0 ∆ 3 0 , 0 0 5 0 1 4 7 0 0 , 7 9 1 5 , 0 06 9 0 1 7 , 3 2V r a n g e 3 8 0 ÷ 4 2 0 ∆ , 6 6 0 ÷ 7 2 0 ± 5%I C 4 1 1 C L F T a 4 0 ° C S 1i t e m k g 1 9 5

Manufacturer Cemp srl - I 20030 SENAGO (Milan) - ITALYregrease joints after any dismounting - fasteners quality 8.8 EN 898-1

YY

28

ENGLISH

2.3 Materials, painting and nameplate

Nameplate

2.3 Materials, painting and nameplate

The stainless steel nameplate is fitted on themotor frame.

Fig. 2 A

Materials

Table 2 D - Materials of the main components:

Frame size 63 ÷ 250 280 ÷ 315

FrameEndshieldsTerminal box

Cast iron G200 (ISO 185) Cast iron G200 (ISO 185)

Fan coverRain cap

Steel Steel

Fan Non sparking thermoplastic material or aluminium Aluminium

Shaft Steel C40 Steel C40

Rotor Squirrel cage in pressure cast aluminium Squirrel cage in pressure cast aluminium

Winding Insulation class F or H Insulation class F or H

Bolts and screws Galvanised steel 8.8 or A4-80 UNI EN ISO 3506-1 Steel 8.8 zinc plated

Cable gland (on request) Brass or stainless steel Brass or nickel-plated brass

Painting - Table 2 E - Paint system and characteristics

Frame size 63 ÷ 250 280 ÷ 315

PretreatmentAll components are sandblasted, cleaned anddegreased

All components are sandblasted, cleaned anddegreased

PaintingPolymerised epoxy polyester powder, oven-baked at200°C

Treatment with anti-corrosion primer

Final coat of enamel paint

ThicknessTotal 120 µm (different thicknesses available uponrequest)

Total 120 µm (different thicknesses available uponrequest)

Colour RAL 5010 (special colours available upon request) RAL 5010 (special colours available upon request)

Mechanical strengthNon-abrasive, elastic, insensitive to scratches,resistant to impact

Non-abrasive, elastic, insensitive to scratches,resistant to impact

Corrosion resistance Highly resistant to water, water vapour, salt water Highly resistant to water, water vapour, salt water

Chemical resistanceGood resistance in chemically aggressiveenvironments

Good resistance in chemically aggressiveenvironments

Temperature range -40 °C +130°C -40 °C +130°C

29

ENGLISH

2.4 Shaft ends, balancing, vibrations, noise levels, coupling and belt drives

2.4 Shaft ends, balancing, vibrations, noise levels, coupling and belt drives

Shaft ends

The shaft ends are cylindrical and complywith IEC 60072 in their design and in theircorrespondence to frame sizes and outputs.

The shaft ends of all motors are equippedwith a tapped hole to assist in the fitting ofpulleys and couplings.

The keys are always supplied along withthe motors.

On request, special shaft ends or a secondfree shaft end can be provided.

Pole-changing motors with a 2-pole speedhave the same shaft ends as single-speed2-pole motors.

Balancing, and vibration

The motors are dynamically balanced withhalf keys in accordance with vibration grade“A” (N) normal balance IEC 60034-14 (andISO 8821).

The low-vibration version “B” (R) (reduced)can be supplied where high demands aremade on quiet running.

Care must be taken to ensure thattransmission parts (pulleys, couplings)supplied by others are dynamically balancedwith half key.

Noise level

Noise measurements are performed toIEC 60034-9.

In the performance data, the sound pressurelevels “Lp” are given in dB (A) for theindividual frame sizes.

They apply for no load at 50 Hz.The tolerance is + 3 dB (A).

At 60 Hz the values of sound pressureincrease approximately by 4 dB (A).

Coupling drive

When aligning a motor to be coupled direct-ly to the machine, care must be taken thatthe rollers and balls of the bearings do notjam.Elastic couplings are permissible with allmotors.

To ensure vibration-free running and toavoid any inadmissible stress on thebearings, the machine to be coupled muststill be exactly aligned in the case of elasticcoupling.

Maximum accuracy must be applied to thecoupling of 2-pole motors.

Belt drive

Slide rails are used for motors for easytensioning and readjustment at the belts.

Permissible forces have to be taken intoconsideration (See Table 2 I).

Pulleys and couplings must only befitted and removed by means of specifictools.

Table 2 F - Vibration limits according to IEC 60034-14

Terms of measure: Free standing

Balancing rate

Limit values of the speed of vibration/oscillation for framesizes:

63 ÷ 132[mm/s]

160 ÷ 280[mm/s]

315[mm/s]

A 1.6 2.2 2.8

B 0.7 1.1 1.8

30

ENGLISH

2.5 Bearing system2.5.1 Bearing system

2.5.1 Bearing system

Table 2 G - Standard model -Closed non-lubricated bearings

Framesize Poles

Bearing

Drive end Non-Driveend

63 2 - 4 - 6 - 8 6202 ZZ

71 2 - 4 - 6 - 8 6203 ZZ

80 2 - 4 - 6 - 8 6204 ZZ

90 2 - 4 - 6 - 8 6205 ZZ

100 2 - 4 - 6 - 8 6206 ZZ

112 2 - 4 - 6 - 8 6306 ZZ

132 2 - 4 - 6 - 8 6308 ZZ C3

160 2 - 4 - 6 - 8 6309 ZZ C3

180 2 - 4 - 6 - 8 6310 ZZ C3

200 2 - 4 - 6 - 8 6312 ZZ C3

225 2 - 4 - 6 - 8 6313 ZZ C3

2502 6313 ZZ C3

4 - 6 - 8 6314 ZZ C3 6313 ZZ C3280

horizontal 2 - 4 - 6 - 8 6316 ZZ C3

280vertical

2 - 4 - 6 - 8 6316 C3

315horizontal

2 6316 ZZ C3

4 - 6 - 8 6317 ZZ C3 6316 ZZ C3

315vertical

2 6316 C3

4 - 6 - 8 6317 C3 6316 C3

Table 2 H - Upon request -Open bearings with lubricators

* Grease type LGHP2 SKF or equivalent.

Framesize Poles

BearingTime intervalfor lubrication

(hours)

Amount ofgrease*Front ball

bearingsFrontrollers

Rear ballbearings

160

2

6309 C3 NU 309 6309 C3

5500

12 g4 8250

6 - 8 11000

180

2

6310 C3 NU 310 6310 C3

2000 12 g

4 600015 g

6 - 8 7000

200

2

6312 C3 NU 312 6312 C3

2100 12 g

4 500015 g

6 - 8 7000

225

2

6313 C3 NU 313 6313 C3

2000 15 g

4 4500

18 g6 5600

8 6400

250

2 6313 C3 NU 313

6313 C3

2000 18 g

4

6314 C3 NU 314

4100

20 g6 5300

8 6200

280 S

2

6316 C3 NU 316 6316 C3

4100

33 g4 5000

6 5250

8 5800

280 M

2

6316 C3 NU 316 6316 C3

3700

33 g4 4300

6 4600

8 4800

315 S

2 6316 C3 NU 316

6316 C3

3300 33 g

4

6317 C3 NU 317

9500

37 g6 13700

8 15300

315 M

2 6316 C3 NU 316

6316 C3

2900 33 g

4

6317 C3 NU 317

7800

37 g6 11300

8 13600

315 LA

2 6316 C3 NU 316

6316 C3

4100 33 g

4 - 66317 C3 NU 317

1110037 g

8 19500

315 LB

2 6316 C3 NU 316

6316 C3

3500 33 g

4 - 66317 C3 NU 317

950037 g

8 16550

315 LC

2 6316 C3 NU 316

6316 C3

2900 33 g

4 - 66317 C3 NU 317

780037 g

8 13600

31

ENGLISH

2.52.5.1 Bearing system2.5.2 Bearing section

2.5.1 Bearing system

Standard motors are equipped with radialdeep groove ball bearings (ZZ pre-greasedseries) or open bearings complete withgrease nipples.

Where requested roller, or other specialbearings can be fitted.

Lubrication

The ZZ series bearings are lubricated for lifeand require no further lubrication.

Open bearings are supplied with grease nip-ples and are to be lubricated according tothe indications given in the table 2 G - 2 H.

Bearing Seal

In order to prevent dust and waterpenetration, a seal ring is fitted to theendshield on the driving and non-drivingends.

These seal rings are highly resistant tovibrations, thermally stable, and resistant tomineral oils and diluted acids.

Seals for media not listed above areavailable on request.

2.5.2 Bearing section

63 ÷ 132 160 ÷ 250 280 ÷ 315

Fig. 2 BBall bearings - DE (front)

160 ÷ 250 280 ÷ 315

Fig. 2 CRoller bearings - On request execution DE (front)

optional optional(for open bearings) (for open bearings)

32

ENGLISH

2.5.3 Permissible radial loads on the shaft with standard bearings

Table 2 I shows the values of radial loadcalculated considering:- frequency 50 Hz- temperature not exceeding 90°C- 20,000 hours of life for 2-pole motors;- 40,000 hours of life for 4, 6, 8-pole motors

For operation at 60 Hz the values haveto be reduced by 6% in order to achievethe same useful life. For double speedmotors consider always the higher speed.

The distance of the point of action of forceFR from the shoulder of the shaft must notexceed the length of the shaft end.

FR = maximum radial load (e. g.belt load + weight of belt pulley)

F = belt load [N] = 2 · K · MD

M = torque [Nm] = 9550 · Pn

P = rated motor output [kW]

n = rated motor speed [1/min]

D = belt pulley diameter [m]

K = prestress factor governed bybelt type: it is assumedapproximately as follows

K = 3 for normal flat belts withouttensioning pulley

K = 2 for normal flat belts withtensioning pulley

K = 2.2 for V-belts or special flat belts

2.52.5.3 Permissible radial loads

Table 2 I

Framesize

Polenumber

Permissible radial load FR [N]

Ball bearings Roller bearings

X0 X1 X2 X0 X1 X2

63

2468

390390440490

360360410450

340340380420

------------

------------

------------

71

2468

490480550610

450450510560

420420480520

------------

------------

------------

80

2468

640640730800

590580660730

540540610670

------------

------------

------------

90

2468

730720820910

660660750820

610600680750

------------

------------

------------

100

2468

1020101011501270

91091010301140

8308209401030

------------

------------

------------

112

2468

1480147016801850

1350134015301680

1240123014101550

------------

------------

------------

132

2468

2160214024502700

1930191021902410

1750172019702180

------------

------------

------------

160

2468

2790277031503480

2470245027903080

2210219024902750

5720588559956050

5200535054505500

4680481549054950

180

2468

3600350039004300

3200335036003950

2950285033003700

6490704073707480

5900640067006800

5310576060306120

200

2468

4500455053005500

4300435055005350

4000410050005050

9680104501078010945

8800950098009950

7920855088208955

225

2468

5500535059506400

5000490056506100

4650450052005700

11880127601320013420

10800116001200012200

9720104401080010980

250

2468

5300565058206420

5100540056005980

4750530053705520

13860159501650016665

12600145001500015150

11340130501350013635

280

2468

5500566569307920

5000515063007200

4500463556706480

15400159501650018150

14000145001500016500

12600130501350014850

315 S-M

2468

5500627073708360

5000570067007600

4500513060306840

14300280502915029700

13000255002650027000

11700229502385024300

315 L

2468

6820709580309020

6200645073008200

5580580565707380

13640247502750030800

12400225002500028000

11160202502250025200Fig. 2 D

33

ENGLISH

2.52.5.4 Permissible axial load on the shaft

2.5.4 Permissible axial load on the shaft with standard bearings

If the shaft end is loaded at X2 with thepermissible radial load FR an additional axialload FA is allowed (table 2 L).

If the permissible radial load is not fullyutilized, higher loads are possible in axialdirection (Values on request).

B3

V5

V6

Fig. 2 F

Push

Pull

Pus

h

Pul

l

Pus

h

Pul

l

Fig. 2 E

Table 2 L

Framesize

Polenumber

Limit axial load with FR at X2 - FA [N]

Ball bearings Roller bearings

B3push/pull

V5/V6push/pull

B3push/pull

V5/V6push/pull

63

2468

120120140160

110110130150

------------

------------

71

2468

140140170190

130120150170

------------

------------

80

2468

190190220250

170160190220

------------

------------

90

2468

200200240270

170160190220

------------

------------

100

2468

280280330370

230220260300

------------

------------

112

2468

410410480540

330320370430

------------

------------

132

2468

590590690780

430380470560

------------

------------

160

2468

7507508801000

490450520640

1000120013001400

700840910980

180

2468

88088010301160

950115013501550

1000125013501550

7008759451085

200

2468

1160116013601520

1100120014001600

1100120014001600

7708409801120

225

2468

1300130015201710

1250135016001850

1250135016001850

87594511201295

250

2468

1460146017101920

1300140016001920

1300140016001900

91098011201330

280

2468

5500550065007400

3850385045505180

3700370040004500

2590259028003150

315 S-M

2468

5500580068007650

3850406047605355

3700350040004500

2590245028003150

315 L

2468

2200220025003000

1540154017502100

3850380046005500

2695266032203850

63 ÷160 180 ÷ 315

34

ENGLISH

2.6 Terminal box2.6.1 Terminal box design

2.6.1 Terminal box design

On request we can supply:

- additional terminal box for auxiliary terminals (Fig. 2 H)- motors without terminal box and with leads (Fig. 2 I)- bigger terminal box with capacitor for single phase motors (Fig. 2 L).

The standard design has four basic versions:

- Ex d IIB- Ex d IIC- Ex de IIB- Ex de IIC

Fig. 2 G - Terminal box, design IIB

Fig. 2 H Fig. 2 I Fig. 2 L

35

ENGLISH

Fig. 2 M - Positioning of the cableentry, plan view

2.62.6.2 Position of terminal box and terminals2.6.3 Cable-entries

2.6.2 Position of terminal box and terminals

The terminal box is usually located on topand can be turned through 4 x 90° (Fig. 2M).

For a horizontal mounted motor the cableentry is normally located on the right side(looking at the driving-end).

Cable entry:

- standard position: 1

- special positions upon request: 2, 3, 4.

Terminals and earthing terminalThere are a maximum number of 6 powerterminals in the terminal box.

The type of monitoring device depends onthe number of possible additional terminalsin the main terminal box.

PTC thermistors can be connected to twoadditional terminals.Two terminals are also necessary forconnecting the anticondensation heater.

For PT 100 (RTD) thermistors, 3 or 4terminals are necessary depending on thetype chosen.

An earthing terminal is located in theterminal box and another earthing terminal islocated on motor frame.

3

1

24

Table 2 N

* Other threads available upon request

Mains connection cable entries

Framesize

Mains powersupply

Power supply froman inverter

Conical threadingupon request*

ANSI B 2.1 UNI 6125

63 ÷ 112 1 x M25 1 x M25 + 1 x M20 NPT 3/4” Gk 3/4”

132 ÷ 160 2 x M32 1 x M32 + 1 x M20 NPT 1” Gk 1”

180 ÷ 250 2 x M40 1 x M40 + 1 x M20 NPT 1.1/2” Gk 1.1/2”

280 ÷ 315 2 x M63 1 x M63 + 1 x M20 NPT 2” Gk 2”

Auxiliaries cable entries

63 ÷ 315 ---- 1 x M20 NPT 1/2” Gk 1/2”

2.6.3 Cable-entries

As standard, the motors are delivered withone or two threaded cable entries forflameproof packing glands.

Ex de motors can be also provided withEx e packing glands.

Motors fitted with thermodetectors orheaters are always provided with additionalcable entry.

Output

The rated outputs and operatingcharacteristics given in the performancedata refer according to IEC 60034-1 to:- continuous duty (S1)- frequency of 50Hz- voltage 400V (230V for single phase)- maximum ambient temperature of 40 °C- maximum height of installation of 1000 mabove sea level.

Motors can also be operated in ambienttemperatures from 40 °C up to 80 °C and ataltitudes of more than 1000 m up to 4000 mabove sea level.

In these cases the rated output given in thetables must be reduced in accordance withtable 3 A or a larger motor has to bechosen.

The rated data does not need to bechanged if at altitudes in excess of 1000 mabove sea level the ambient temperature isreduced according to the following table:

Altitude of Maximum ambientinstallation [m] temperature [°C]

0 to 1000 401000 to 2000 302000 to 3000 19

3000 to 4000 9

Voltage, frequency

The motors as standard are built to run atthe voltage and frequency with thetolerances indicated in figure 3 A.

The motors can run with the variationsenvisaged in normal operational areas at avoltage of ± 5% and frequency of ± 2%.

Furthermore, the motors can be used in theoperational area with restrictions (variationsin voltage of ± 10% and frequency of ± 3%)as long as the indications given by norm60034-1 are complied with.

36

ENGLISH

3. Electrical design3.1 Standard operating conditions

3.1 Standard operating conditions

Power [%]

130

120

110

100

90

80

70

60

50

Height of installation [m]

0 - 1000 2000 3000 4000

10 20 30 40 50 60 70 80Ambient temperature [°C]

Table 3 A - Power variation of standard motors in case of coolant temperature differentfrom 40 °C or height of installation over 1000 m above sea-level

1,03

1,05

1,10

1,00 1,030,95

0,97

0,95

0,93

0,90

Normaloperationalarea

Operational area with restrictions

0,98 1,02X =

Working frequency

Rated frequency

Y =Working voltage

Rated voltage

Ratedcharacteristicspoint

Fig. 3 A

Speed

The rated speeds shown in the performancedata are valid for 50 Hz and the rated speedequals synchronous speed less slip.

The following speeds result from the numberof poles and the mains frequencies of 50and 60 Hz:

PoleNo-load speed at

number 50 Hz 60 Hz[1/min] [1/min]

2 3000 36004 1500 18006 1000 12008 750 90010 600 72012 500 60016 375 450

Direction of rotation

The motors can be operated in bothdirections of rotation. If the phases areconnected in the sequence L1, L2, L3 to theterminals U1, V1, W1, the motor turnsclockwise.

The direction of rotation can be reversed byinterchanging any two phases.

Note regarding electro-magneticcompatibility

Low voltage induction motors, if installedcorrectly and connected to the powersupply, respect all immunity and emissionlimits as set out in the regulations relating toelectro-magnetic compatibility (EMC“Generic Standard” for industrialenvironments).

In the case of supply by means of electronicimpulse devices (inverters, soft starters etc.),all verifications and any modifications,necessary to ensure that emission andimmunity limits, as stated within theregulations, are respected, are theresponsibility of the installer.

37

ENGLISH

Tolerances

According to IEC 60034-1 the electrical datastated in the tables are subject to thefollowing tolerances:

Efficiency:Pn ≤ 50 kW: - 0.15 (1-η)

Pn > 50 kW: - 0.10 (1-η)

Power factor: - 1 - cos ϕ

6

(minimum 0.02 - maximum 0.07)

Slip at rated load operating temperature:± 20% of rated slip.

Locked rotor torque (starting torque):- 15% + 25%

Maximum torque: - 10%.

Current with locked rotor: + 20% (no lowerlimit).

Torque

The motors are fitted with squirrel-cagerotors suitable for direct-on-line starting.

The resulting starting and maximumtorques, expressed as a multiple of the ratedtorques are given in the performance data.

A deviation in the voltage from the ratedvalue changes the torques as anapproximate function of the square of thevoltages.

Normally two-speed motors have a nominaltorque that is roughly the same for bothspeeds.

A version is also available with quadratictorque, for centrifugal machines (fans,pumps). In this case, the torque at the lowerspeed is roughly half that available at thehigher speed.

Rated current

In the performance data the rated currentsare only indicated for a rated voltage of400V.

For other voltages the rated currents areinversely proportional to the voltages:

U = I'U' I

This results in:

I' = U · IU'

3.1

3.1 Standard operating conditions

38

ENGLISH

3.2 Efficiency and power factor at partial load

3.2 Efficiency and power factor at partial load

The efficiency and power factor valuesshown in the performance data refer to ratedoutput at 50Hz.

Values at partial load given in table 3 B, 3 Care for approximate reference only.

Table 3 B

Efficiency in % at

1/2 3/4 4/4 5/4

of full load

94

93

92

91

91

89

88

87

86

85

85

84

83

82

80

79

78

77

75

74

73

72

71

70

68

67

66

65

64

62

61

60

59

95

94

93

92

92

91

90

89

88

87

86

86

85

84

82

81

80

79

78

77

76

75

74

73

72

71

70

69

67

66

65

64

63

969594939291908988878685848382818079787776757473727170696867666564

95

94

93

92

91

90

88

87

86

84

84

83

82

81

80

79

78

77

76

75

74

73

72

71

70

69

68

67

66

65

64

63

62

Table 3 C

Power factor at

1/2 3/4 4/4 5/4

of full load

0.85

0.84

0.81

0.80

0.77

0.75

0.73

0.71

0.69

0.68

0.67

0.65

0.64

0.62

0.61

0.60

0.58

0.57

0.55

0.54

0.53

0.52

0.50

0.49

0.48

0.47

0.46

0.45

0.44

0.43

0.42

0.41

0.40

0.91

0.90

0.88

0.87

0.86

0.84

0.83

0.81

0.80

0.79

0.78

0.77

0.75

0.74

0.72

0.71

0.70

0.69

0.67

0.66

0.65

0.63

0.62

0.61

0.59

0.58

0.57

0.56

0.55

0.54

0.53

0.52

0.51

0.930.920.910.900.890.880.870.860.850.840.830.820.810.800.790.780.770.760.750.740.730.720.710.700.690.680.670.660.650.640.630.620.61

0.93

0.92

0.91

0.91

0.90

0.89

0.88

0.88

0.87

0.87

0.86

0.85

0.85

0.84

0.83

0.82

0.81

0.80

0.79

0.79

0.78

0.77

0.76

0.75

0.74

0.74

0.73

0.72

0.71

0.70

0.69

0.68

0.67

39

ENGLISH

3.3 Insulation and temperature rise

3.3 Insulation and temperature rise

Insulation

The components of the insulation systemwere selected so as to ensure goodprotection against chemically aggressivegases, vapours, dust, oil and air humidity.All materials used for insulating the windingand winding ends correspond to insulatingclasses F or H according to IEC 60085:• Enamel-insulated copper wires withtemperature index 200 (class H);

• Insulating sheet on polyester base(class F);

• Impregnation with fenolic resins modifiedwith polyesther resins (class H);

Table 3 D - Limit temperature forinsulating material according IEC 60085

Temperature rise

Standard single-speed motors in continuousservice (excluding 315M) have temperaturerises that are within the limits for class B.

Motors with higher output andpole-changing motors normally havetemperature rise within class F limit.

Table 3 E - Temperature rise limit forrotating machines according IEC 60034-1

According to Normative IEC 60034-1, thevalues shown in the table above may be upto 10 °C higher, with a feeding current vari-ance of ± 5%.

Insulationclass

Max temperaturerise [K]

BFH

80105125

Insulationclass

Limit temperature[°C]

BFH

130155180

40

ENGLISH

N

a

b

c

d

max

R

t

N

a

b

c

d

max

3.4 Duty types

In compliance with IEC 60034-1 thefollowing duty-types are distinguished:

Duty-type S1 - continuous running duty.Constant load operation.

Duty-type S2 - short-time duty.Operating times of 10, 30, 60, and 90minutes are recommended.After each operating period the motorremains de-energized until the winding hascooled down to the ambient temperature.

Duty-type where start-ups DO NOTINFLUENCE winding over-heating:

Duty-type S3 - intermittent periodic duty.Where starting does not influence thetemperature. Duty cycle 10 minutes unlessotherwise agreed upon. For the cyclicduration factor the values 15, 25, 40, and60% are recommended.

Duty-type S6 - continuous operationperiodic duty.Duty cycle 10 minutes unless otherwiseagreed upon. For the cyclic duration factorthe value 15, 25, 40, and 60% arerecommended.

N.B.:The output ratings stated in the“Performance data” (Chapter 4.) apply toduty-type S1.

Duty-types where starting and brakinghave a corresponding INFLUENCE on thetemperature rise of the winding:

Duty-type S4 - intermittent periodic dutywith starting.Intermittent periodical operation withidentical cycles.

Duty-type S5 - intermittent periodic dutywith electric braking.Intermittent periodical operation withidentical cycles, which include an electricalbraking phase.

For S4 and S5 duty-types the followingdetails must be given after this code:- Intermittence ratio;- The number of starts per hour;- Moment of inertia of the motor;- Moment of inertia of the load.

Duty-type S7 - continuous operationperiodic duty with electric braking.

Duty-type S8 - continuous operationperiodic duty with related load/speedchanges.

Duty-type S9 - duty with non-periodicalload and speed variations.Typical operation for motors powered byfrequency converters.

Most of the real duty-type conditionsrepresent a combination of duty-types asmentioned under 1. and 2.In order to exactly determine a suitablemotor details of all the operating conditionsare required.

N

a

b

c

d

max

Fig. 3 C - Duty type S2

Fig. 3 B - Duty type S1

Fig. 3 D - Duty type S3

3.4 Duty types

N

a

b

c

d

max

R

t

D

Fig. 3 E - Duty type S4

NIntermittence ratio = · 100%

N + R

D + NIntermittence ratio = · 100%

D + N + R

41

ENGLISH

N1

a

b

c

d

max

t

D

e

F1

N2 F2

N3

3.4 Duty types

a = Loadb = Electrical lossesc = Temperatured = Timee = Speedt = Cycle lengthD = Start-up or acceleration timeF, F1, F2 = Electrical braking timeN, N1, N2, N3 = Constant load operating timeL = Variable load operating timeV = No-load operating timeR = Rest timeS = Overload operating timeP = Full loadθmax = Maximum temperature reached during cycle

N

a

b

c

d

max

R

t

D F

Fig. 3 F - Duty type S5

N

a

b

c

d

max

V

t

Fig. 3 G - Duty type S6

N

a

b

c

d

max

t

D F

Fig. 3 H - Duty type S7

Fig. 3 L - Duty type S9

Fig. 3 I - Duty type S8

a

b

c

d

max

S

e

D R

FL

P

Table 3 F - Simbology

D + N + FIntermittence ratio = · 100%

D + N + F + R

Intermittence ratio = 1

Intermittence ratio =

D + N1· 100%

D + N1 + F1 + N2 + F2 + N3

F1 + N2· 100%

D + N1 + F1 + N2 + F2 + N3

F2 + N3· 100%

D + N1 + F1 + N2 + F2 + N3

NIntermittence ratio = · 100%

N + V

42

ENGLISH

3.5.1 Three-phase motors

Single-speed motors are normallypre-arranged to be connected in star ordelta method.

Star connection

Connecting together the W2, U2, V2terminals (star point) and connecting to themains the U1, V1, W1 terminals a starconnection is obtained.

The phase current Iph and the phasevoltage Uph are the following:

Iph = In

Uph = Un / ED3

where In the line current and Un is the linevoltage.

Delta connection

Connecting the end of each winding to thebeginning of the next winding a deltaconnection is obtained.

The phase current Iph and the phasevoltage Uph are the following:

Iph = In / ED3

Uph = Un

Star - Delta starting

The star-delta starting is an easy way toreduce the starting current and startingtorque.

Motors can be started with the star-deltastarting method whenever the supplyvoltage correspond to the rated voltage ofthe motors in delta connections.

3.5 Connecting diagrams3.5.1 Three-phase motors

Two speed motors

Standard two speed motors are designedfor only one rated voltage and for directstarting.

When the speed ratio is 1/2 the standardmotors have one winding (Dahlanderconnection).

For other speed ratios the motors have twodifferent windings.

Un

L2L1 L3

Uph

V1U1 W1

V2U2 W2

Uph

I ph

L2L1

Un

L3

I ph

In

Fig. 3 N

Un

L2L1 L3

I phUph

V1U1 W1

V2U2 W2 Star point

L2L1

Uph

UphI ph

Un

L3

Fig. 3 M

43

ENGLISH

3.5.1 Three-phase motors

Connection for single speed motors:

Number of pole: 2, 4, 6, 8 ......Synchronous speed at 50 Hz: 3000, 1500, 1000, 750 .....

U2W2 V2

W1V1U1

L1 L2 L3Y-Connection

U1

W1 V1

U1

W2 U2 V2

L1 L2 L3

V1 W1

V1W1

U1

∆-Connection

Two separate windings for two speed motors:

Number of pole: 2/6, 2/8, 4/6, 6/8Synchronous speed at 50 Hz: 3000/1000, 3000/750, 1500/1000, 1000/750.

U1

W2 U2 V2

L1 L2 L3

V1 W1

Low Speed

U1

W1 V1High Speed

W2

V2 U2

U1

W2 U2 V2

V1 W1

L1 L2 L3

Dahlander system for two speed motors:

Number of pole: 2/4, 4/8Synchronous speed at 50 Hz: 3000/1500, 1500/750.

U1

W2 U2 V2

L1 L2 L3

V1 W1

V1W1

U1

Low SpeedU2

V2 W2

High SpeedU2

W2

V2

W1

V1

U1

V1 W1U1

W2 U2 V2

L1 L2 L3

3.53.5.1

Fig. 3 O - Three phase motors connecting diagrams

44

ENGLISH

3.53.5.2 Single phase motors3.5.3 Additional terminal marking

3.5.2 Single phase motors

Single phase motors are designed for onlyone rated voltage.

They have two windings (starting and mainwinding) which have to be connected to thecapacitor supplied with the motor.

The sense of rotation can be reversedaccording to the connecting diagram.

Fig. 3 P - Single phase motors connecting diagram

µFCapacitor

L1 L2

U1

W2 U2 V2

V1 W1

L1 µFCapacitor

U1

W2 U2 V2

V1 W1

L2

Direction of rotation,clockwise

Direction of rotation,anticlockwise

3.5.3 Additional terminal marking (IEC 60034-8)

Motors fitted with accessories are suppliedwith additional terminals, marked asindicated in Table 3 G.

Table 3 G

(*) U rated = 6V - max 30V - (**) U rated = 250V

Marking Nr. terminals Additional terminal for:

TP1 - TP2 (warning)TP3 - TP4 (switch off)

22

Thermistor PTC (*)

R1 - R2 - R3 (I sensor)R4 - R5 - R6 (II sensor)R7 - R8 - R9 (III sensor)

333

Thermistor PT 100 with 3 wire

R11 - R12 - R13 (DE)R21 - R22 - R23 (NDE)

33

Thermistor PT 100 on bearing

TB1 - TB2 (warning)TB3 - TB4 (switch off)

22

Normally closed bi-metallic switch (**)

TB8 - TB9 (switch off) 2 Normally closed brake bi-metallic switch (**)TM1 - TM2 (warning)TM3 - TM4 (switch off)

22

Normally open bi-metallic switch (**)

HE1- HE2 2 Space heaters

U1 - U2 2 Single phase forced ventilation

U - V - W 2 Three phase forced ventilation

colours according manufacturer diagram 9 Encoder

CA1 - CA2 2 Capacitor

PE 1 Earth cable

45

ENGLISH

3.6 Protection devices

In order to protect the winding of athree-phase induction motor against thermaloverloads, resulting in example fromoverloading and operation with only twophases, one of the following devices can beprovided:

• Bimetallic type device:it consists of 2 motor protectorsconnected in series. The contact isnormally closed; the disc opens when thewindings temperature reaches limitsdangerous for the insulation system.On request normally open device areavailable.

• PTC temperature sensor(thermistors):it consists of 3 sensors connected inseries embedded in stator windings.

Once reached the operating temperature,this device quickly changes theresistance; it must be connected to asuitable releasing device (supplied onlyon request).

• PT 100 (RTD) thermometric resistors(from size 132 and above).The resistance value of this device variesaccording to the windings temperature.

They are particularly suitable for acontinuous survey of the windingstemperature.

For a good survey at least two set ofPT 100 are requested; they must beconnected to their proper monitoringequipment (supplied only on request).

PTC and PT 100 also offer reliableprotection for operating modes other thancontinuous operation, e. g. short-timeoperation, switching operation, longtimestart-up as well as for reduced cooling airflow rates and high ambient temperatures.

Motors for operation with frequencyconverter are always supplied with PTCthermistor temperature detectors.

Above devices have their proper terminalblock located inside main box.

Upon request also available with separateterminal box.

3.6 Protection devices

46

ENGLISH

3.7 Frequency converter driven motors

Motors with enclosures in protection type“d”, “de” are designed for variable speeddrives.

Chapter 4.5 lists the electrical data indifferent working conditions of the Ex d,Ex de motors shown in this catalogue.

Specific type-approvals are needed formotors with protection type Ex e, while inmany countries motors with protection typeEx nA are strongly restricted.

When using a squirrel cage “Ex d” motorwith a frequency converter the followingpoints must be taken into account inaddition to the general selection criteria:

• The voltage (or current) fed by thefrequency converter is not purelysinusoidal.

As a result it may increase the losses,vibration, and noise of the motor.

Futhermore, a change in the distributionof the losses may affect the motortemperature balance.

In every case, the motor must becorrectly sized according to theinstructions supplied with the selectedfrequency converter and with ourtechnical data.

• In a frequency converter drive the actualoperating speed of the motor may deviateconsiderably from its rated speed.

For higher speeds it must be ensured thatthe highest permissible speed of rotationof the motor, or the critical speed of theentire equipment, is not exceeded.

In addition, bearing lubrication and anyventilation noise suppressionarrangements will require specialattention.

• The torque values shown in this cataloguefor motors with constant torque atfrequencies over 60Hz can be stablysupplied only if the motor has a deltaconnection.

For example, to stably achieve these val-ues from a 230/400V 50Hz winding motorwith a 400V 50Hz mains voltage supply,the motor must have a delta connectionand, consequently, the inverter must beconfigured so that at 50Hz it supplies avoltage of 230V.

Vice-versa, with a star connection, thevalues listed can be supplied only for veryshort periods.

• Operating periods at a speed above 36001/min must never exceed 10% of theentire work cycle of the motor to ensurethe bearings last accordingly.

• If the rated voltage is 690V or if there is along feeding cable between the motorand the frequency converter, the insula-tion of the motor must be reinforcedbecause of the occuring voltage peaks.

A correct earthing of the motor and thedriven equipment is also important to avoidbearing currents and voltages.

3.7 Frequency converter driven motors

The features of motors for use in constanttorque and those for use in quadratictorque are indicated in section 4.5.

Section 4.5.1 contains graphs showingloading curves for the use of variabletorque motors.

The reference torque value (Mn) is thevalue indicated in the tables in section 4.1.

207

4. Performance data4.1 Three-phase motors, 1 speed4.2 Three-phase motors, 2 speeds, for general purpose (constant torque)4.3 Three-phase motors, 2 speeds, for centrifugal machines (quadratic torque)4.4 Single-phase motors, 1 speed4.5 Motors energized by inverter

4. Données nominales4.1 Moteurs triphasés, 1 vitesse4.2 Moteurs triphasés, 2 vitesses, pour usage général (couple constant)4.3 Moteurs triphasés, 2 vitesses, pour machines centrifuges (couple quadratique)4.4 Moteurs monophasés, 1 vitesse4.5 Moteurs alimentés par variateur

4. Betriebsdaten4.1 Drehstrom Motoren, 1 Drehzahl4.2 Drehstrom Motoren, 2 Drehzahlen, für allgemeinen Gebrauch (konstantes Gegenmoment)4.3 Drehstrom Motoren, 2 Drehzahlen, für Zentrifugalmaschinen (quadratisches Gegenmoment)4.4 Einphasen Motoren, 1 Drehzahl4.5 Motoren mit Umrichterversorgung

4. Datos nominales4.1 Motores trifásicos, 1 velocidad4.2 Motores trifásicos, 2 velocidades, para uso general (par constante)4.3 Motores trifásicos, 2 velocidades, para máquinas centrifugas (par cuadrático)4.4 Motores monofásicos, 1 velocidad4.5 Motores alimentados con inverter

4. Dati nominali4.1 Motori trifase, 1 velocità4.2 Motori trifase, 2 velocità, per uso generale (coppia costante)4.3 Motori trifase, 2 velocità, per macchine centrifughe (coppia quadratica)4.4 Motori monofase, 1 velocità4.5 Motori alimentati da inverter

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

ITALIANO

209208

AB30 63 A 2 AB35 63 A 2 AC30 63 A 2 AC35 63 A 2 0.18 2857 0.75 63.00 0.57 0.63 4.4 3.6 3.8 60 52 0.0001 16 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4AB30 63 B 2 AB35 63 B 2 AC30 63 B 2 AC35 63 B 2 0.25 2805 0.85 66.00 0.66 0.85 3.9 3.5 3.7 60 52 0.0001 16 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4



AB30 90 S 2 AB35 90 S 2 AC30 90 S 2 AC35 90 S 2 1.50 2845 3.26 79.00 0.84 5.04 6.2 2.3 2.5 77 69 0.0012 33 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4AB30 90 L 2 AB35 90 L 2 AC30 90 L 2 AC35 90 L 2 2.20 2820 4.53 80.50 0.87 7.45 5.5 2.6 2.8 77 69 0.0015 33 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4

AB30 100 LA 2 AB35 100 LA 2 AC30 100 LA 2 AC35 100 LA 2 3.00 2910 6.64 82.50 0.79 9.85 7.5 3.2 3.4 80 72 0.0029 46 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4

AB30 112 M 2 AB35 112 M 2 AC30 112 M 2 AC35 112 M 2 4.00 2900 7.97 84.20 0.86 13.17 6.8 2.0 2.2 80 72 0.0074 65 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4

AB30 132 SA 2 AB35 132 SA 2 AC30 132 SA 2 AC35 132 SA 2 5.50 2905 10.90 85.00 0.86 18.08 6.5 2.8 3.1 81 73 0.0124 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4AB30 132 SB 2 AB35 132 SB 2 AC30 132 SB 2 AC35 132 SB 2 7.50 2925 14.10 86.00 0.89 24.49 6.6 2.5 2.7 83 75 0.0150 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4AB30 132 MB 2 AB35 132 MB 2 AC30 132 MB 2 AC35 132 MB 2 9.20 2900 18.00 84.00 0.88 30.30 7.5 2.8 3.0 83 75 0.0178 105 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4AB30 132 ML 2 AB35 132 ML 2 AC30 132 ML 2 AC35 132 ML 2 11.00 2930 20.00 92.00 0.86 36.00 7.0 2.8 3.1 83 75 0.0216 105 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4

AB30 160 MA 2 AB35 160 MA 2 AC30 160 MA 2 AC35 160 MA 2 11.00 2930 20.00 89.00 0.89 35.85 6.6 2.5 2.8 84 76 0.0360 180 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4AB30 160 MB 2 AB35 160 MB 2 AC30 160 MB 2 AC35 160 MB 2 15.00 2950 26.80 89.70 0.90 48.56 7.0 2.9 3.1 84 76 0.0463 180 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4AB30 160 L 2 AB35 160 L 2 AC30 160 L 2 AC35 160 L 2 18.50 2930 33.00 89.80 0.90 60.30 7.0 2.8 3.1 84 76 0.0534 195 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4

AB30 180 M 2 AB35 180 M 2 AC30 180 M 2 AC35 180 M 2 22.00 2945 39.00 90.60 0.90 71.34 7.5 2.8 3.2 83 74 0.0818 230 06 ATEX 074 Pending 06 ATEX 073 Pending 4

AB30 200 LA 2 AB35 200 LA 2 AC30 200 LA 2 AC35 200 LA 2 30.00 2975 54.00 91.50 0.88 96.30 8.5 3.5 3.7 87 77 0.1625 285 06 ATEX 074 Pending 06 ATEX 073 Pending 4AB30 200 LB 2 AB35 200 LB 2 AC30 200 LB 2 AC35 200 LB 2 37.00 2975 65.00 91.70 0.90 118.77 7.9 2.8 3.2 87 77 0.1947 305 06 ATEX 074 Pending 06 ATEX 073 Pending 4



AB30 280 S 2 AB35 280 S 2 AC30 280 S 2 AC35 280 S 2 75.00 2980 134.00 93.00 0.87 240.35 7.3 2.7 3.3 88 76 0.5200 842 08 ATEX 012 --- 00 ATEX 053 01 ATEX 003X 4AB30 280 M 2 AB35 280 M 2 AC30 280 M 2 AC35 280 M 2 90.00 2985 159.00 93.00 0.88 287.94 8.6 3.1 3.8 88 76 0.6300 881 08 ATEX 012 --- 00 ATEX 053 01 ATEX 003X 4


AB30 315 LA 2 AB35 315 LA 2 AC30 315 LA 2 AC35 315 LA 2 132.00 2984 222.00 94.00 0.92 422.47 7.0 2.0 2.3 99 85 1.8800 1340 08 ATEX 021 --- 07 ATEX 073 --- 4AB30 315 LB 2 AB35 315 LB 2 AC30 315 LB 2 AC35 315 LB 2 160.00 2984 269.00 94.50 0.91 512.21 7.0 1.7 2.0 99 85 2.2500 1430 08 ATEX 021 --- 07 ATEX 073 --- 4AB30 315 LC 2 AB35 315 LC 2 AC30 315 LC 2 AC35 315 LC 2 200.00 2983 332.00 95.20 0.91 640.30 7.4 1.7 2.0 99 85 2.7900 1550 08 ATEX 021 --- 07 ATEX 073 --- 4

Versions that need special installation solutions T3, T5 and T6 see table 1BVersions qui demandent des mesures particulières pour l’installation T3, T5 et T6 voir tableau 1BAusführungen, die bei der Installation besondere Vorsichtsmaßnahmen erfordern T3, T5 und T6 siehe Tabelle 1BVersiones que requieren precauciones especiales de instalación T3, T5 y T6 véase tabla 1BVersioni che richiedono particolari accorgimenti di installazione T3, T5 e T6 vedi tabella 1B

Motor type Rated Speed Current Efficiency Power Torque Starting Starting Maximum Noise level Moment of Mass CESI Certificates Class Toutput factor current torque torque inertia

Moteur type Puissance Vitesse Intensité Rendement Facteur de Couple Intensité Couple Couple Niveau de Moment Masse CESI Certificat Classe Tmécanique puissance démarrage démarrage maximal bruit d'inertie

Motor Typ Leistung Drehzahl Strom Wirkungsgrad Leistungs- Moment Anlauf- Anlauf- Kipp- Schalldruck- Trägheits- Masse CESI Konformitäts-Bescheinigung Klasse Tfaktor strom moment moment pegel moment

Tipo de motor Potencia Velocidad Corriente Rendimiento Factor de Par Corriente de Par de Par Nivel de Momento Peso Certificados CESI Clase Tproporcionada potencia arranque arranque máximo ruido de inercia

Tipo motore Potenza Velocità Corrente Rendimento Fattore Coppia Corrente Coppia Coppia Rumorosità Momento Massa Certificato CESI Classe Tresa potenza avviamento avviamento massima d'inerzia

IIB IIC Pn n In η cos ϕ Mn Ia/In Ma/Mn Mm/Mn [dB(A)] J m IIB IIC

Ex d Ex de Ex d Ex de [kW] [1/min] [A] [%] [Nm] Lw Lp [kgm2] [kg] standard standard

PD2J =4

I'n = In ·

400(I'n = current at U' Volt);U'(I'n = intensité à U' Volt);(I'n = Strom mit U' Volt);(I'n = corriente de U' Voltios);(I'n = corrente a U' Volt);

1400 V50 Hz 3000

ENGLISH

4.4.1

Three-phase motors

II 2GII 2GD

Speed Rated data at direct on line start rpm ENGLISH

FRANÇAIS Moteurs triphasés Vitesse Données nominales à démarrage direct tours/min FRANÇAIS

DEUTSCH Drehstrom Motoren Drehzahl Betriebsdaten bei Direkteinschaltung U/min DEUTSCH

ESPAÑOL Motores trifásicos Velocidad Datos nominales arranque directo rev/min ESPAÑOL

ITALIANO Motori trifase Velocità Dati nominali a avviamento diretto giri/min ITALIANO

211210












AB30 100 LA 4 AB35 100 LA 4 AC30 100 LA 4 AC35 100 LA 4 2.20 1427 5.15 80.10 0.77 14.72 4.4 2.1 2.3 63 55 0.0043 46 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4AB30 100 LB 4 AB35 100 LB 4 AC30 100 LB 4 AC35 100 LB 4 3.00 1436 7.07 81.70 0.75 19.95 4.8 2.4 2.8 63 55 0.0053 46 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4


AB30 132 SB 4 AB35 132 SB 4 AC30 132 SB 4 AC35 132 SB 4 5.50 1455 11.90 87.00 0.77 36.10 6.3 2.4 2.8 72 64 0.0250 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4AB30 132 MB 4 AB35 132 MB 4 AC30 132 MB 4 AC35 132 MB 4 7.50 1460 17.20 86.30 0.73 49.06 5.3 2.7 3.1 75 67 0.0324 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4AB30 132 ML 4 AB35 132 ML 4 AC30 132 ML 4 AC35 132 ML 4 8.80 1455 18.50 87.00 0.79 57.59 6.8 2.5 3.5 75 67 0.0405 105 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4

AB30 160 MB 4 AB35 160 MB 4 AC30 160 MB 4 AC35 160 MB 4 11.00 1465 22.90 89.00 0.78 71.71 6.2 2.5 3.0 77 69 0.0627 180 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4AB30 160 L 4 AB35 160 L 4 AC30 160 L 4 AC35 160 L 4 15.00 1470 31.40 89.50 0.77 97.45 5.9 2.5 3.0 77 69 0.0801 195 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4

AB30 180 M 4 AB35 180 M 4 AC30 180 M 4 AC35 180 M 4 18.50 1470 39.00 89.80 0.76 120.19 6.0 3.2 3.0 79 70 0.1236 230 06 ATEX 074 Pending 06 ATEX 073 Pending 4AB30 180 L 4 AB35 180 L 4 AC30 180 L 4 AC35 180 L 4 22.00 1470 44.00 91.00 0.79 142.93 6.5 2.8 3.1 79 70 0.1493 245 06 ATEX 074 Pending 06 ATEX 073 Pending 4

AB30 200 LB 4 AB35 200 LB 4 AC30 200 LB 4 AC35 200 LB 4 30.00 1470 54.00 91.20 0.88 194.90 6.5 2.5 2.9 82 72 0.2456 305 06 ATEX 074 Pending 06 ATEX 073 Pending 4

AB30 225 S 4 AB35 225 S 4 AC30 225 S 4 AC35 225 S 4 37.00 1480 69.00 91.70 0.84 238.75 7.1 2.7 3.0 84 73 0.3737 360 06 ATEX 074 Pending 06 ATEX 073 Pending 4AB30 225 M 4 AB35 225 M 4 AC30 225 M 4 AC35 225 M 4 45.00 1480 85.00 92.50 0.83 290.37 6.2 2.4 2.8 84 73 0.4479 385 06 ATEX 074 Pending 06 ATEX 073 Pending 4





I'n = In ·


PD2J =4


1400 V50 Hz 1500

ENGLISH

4.4.1

Three-phase motors

II 2GII 2GD






213212

AB30 63 B 6 AB35 63 B 6 AC30 63 B 6 AC35 63 B 6 0.09 850 0.65 38.00 0.52 1.00 2.0 2.3 2.2 48 40 0.0002 16 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4




AB30 100 LB 6 AB35 100 LB 6 AC30 100 LB 6 AC35 100 LB 6 1.50 950 3.80 76.00 0.75 15.08 4.2 2.0 2.3 63 55 0.0088 46 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4


AB30 132 SB 6 AB35 132 SB 6 AC30 132 SB 6 AC35 132 SB 6 3.00 950 7.50 80.00 0.72 30.16 5.8 1.4 1.9 68 60 0.0323 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4AB30 132 MB 6 AB35 132 MB 6 AC30 132 MB 6 AC35 132 MB 6 4.00 970 9.50 81.40 0.75 39.38 6.1 1.7 1.9 68 60 0.0395 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4AB30 132 ML 6 AB35 132 ML 6 AC30 132 ML 6 AC35 132 ML 6 5.50 960 12.30 84.00 0.77 54.71 4.8 1.8 2.0 68 60 0.0506 105 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4

AB30 160 MB 6 AB35 160 MB 6 AC30 160 MB 6 AC35 160 MB 6 7.50 950 15.70 85.00 0.81 75.39 5.9 1.6 2.0 72 64 0.0919 180 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4AB30 160 L 6 AB35 160 L 6 AC30 160 L 6 AC35 160 L 6 11.00 950 21.50 87.00 0.85 110.58 6.2 1.7 2.0 72 64 0.1218 195 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4

AB30 180 L 6 AB35 180 L 6 AC30 180 L 6 AC35 180 L 6 15.00 960 29.00 88.00 0.86 149.22 5.4 1.7 2.2 76 67 0.2263 245 06 ATEX 074 Pending 06 ATEX 073 Pending 4

AB30 200 LA 6 AB35 200 LA 6 AC30 200 LA 6 AC35 200 LA 6 18.50 975 38.00 91.00 0.77 181.21 5.9 1.6 2.1 79 69 0.2986 295 06 ATEX 074 Pending 06 ATEX 073 Pending 4AB30 200 LB 6 AB35 200 LB 6 AC30 200 LB 6 AC35 200 LB 6 22.00 980 44.00 91.70 0.78 214.39 6.1 1.6 2.1 79 69 0.3064 305 06 ATEX 074 Pending 06 ATEX 073 Pending 4




AC30 315 S 6 AC35 315 S 6 AC30 315 S 6 AC35 315 S 6 75.00 990 147.20 94.00 0.79 724.00 6.3 2.6 2.7 79 65 1.6300 965 08 ATEX 012 --- 00 ATEX 053 01 ATEX 003X 4AC30 315 M 6 AC35 315 M 6 AC30 315 M 6 AC35 315 M 6 90.00 990 175.00 94.00 0.79 871.00 4.4 1.8 1.8 79 65 1.8300 991 08 ATEX 012 --- 00 ATEX 053 01 ATEX 003X 4









PD2J =4


I'n = In ·


1400 V50 Hz 1000

ENGLISH

4.4.1

Three-phase motors

II 2GII 2GD






215214












AB30 100 LA 8 AB35 100 LA 8 AC30 100 LA 8 AC35 100 LA 8 0.75 720 2.90 67.00 0.56 9.90 3.40 2.0 2.2 60 52 0.0088 46 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045XAB30 100 LB 8 AB35 100 LB 8 AC30 100 LB 8 AC35 100 LB 8 1.10 675 3.10 75.00 0.68 15.50 2.70 1.8 2.2 60 52 0.0088 46 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4


AB30 132 SB 8 AB35 132 SB 8 AC30 132 SB 8 AC35 132 SB 8 2.20 720 6.50 75.00 0.66 29.20 4.00 1.8 2.3 66 58 0.0323 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4AB30 132 ML 8 AB35 132 ML 8 AC30 132 ML 8 AC35 132 ML 8 3.00 720 8.50 82.00 0.63 40.25 3.90 1.7 2.3 66 58 0.0506 105 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4

AB30 160 MA 8 AB35 160 MA 8 AC30 160 MA 8 AC35 160 MA 8 4.00 718 9.70 85.00 0.70 53.20 4.50 2.3 2.6 70 62 0.0919 180 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4AB30 160 MB 8 AB35 160 MB 8 AC30 160 MB 8 AC35 160 MB 8 5.50 720 14.00 76.00 0.77 73.00 4.10 2.2 2.5 70 62 0.0919 180 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4AB30 160 L 8 AB35 160 L 8 AC30 160 L 8 AC35 160 L 8 7.50 720 18.00 80.00 0.77 99.50 4.30 2.4 2.8 70 62 0.1218 195 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 4

AB30 180 L 8 AB35 180 L 8 AC30 180 L 8 AC35 180 L 8 11.00 718 23.00 87.00 0.79 146.40 5.70 2.2 2.4 73 64 0.2791 245 06 ATEX 074 Pending 06 ATEX 073 Pending 4

AB30 200 LB 8 AB35 200 LB 8 AC30 200 LB 8 AC35 200 LB 8 15.00 735 35.00 89.00 0.70 196.00 5.30 1.6 2.1 75 65 0.4595 305 06 ATEX 074 Pending 06 ATEX 073 Pending 4

AB30 225 S 8 AB35 225 S 8 AC30 225 S 8 AC35 225 S 8 18.50 735 42.25 88.00 0.72 240.33 5.80 2.4 2.7 79 68 0.6337 360 06 ATEX 074 Pending 06 ATEX 073 Pending 4AB30 225 M 8 AB35 225 M 8 AC30 225 M 8 AC35 225 M 8 22.00 730 46.00 88.00 0.79 288.00 5.10 2.1 2.3 79 68 0.7617 385 06 ATEX 074 Pending 06 ATEX 073 Pending 4





PD2J =4


I'n = In ·


1400 V50 Hz 750

ENGLISH

4.4.1

Three-phase motors

II 2GII 2GD






Motor type Ratedoutput Speed Current Efficiency Power

factor Torque Startingcurrent

Startingtorque Noise level Moment of

inertia Mass CESI Certificates Class T

Moteur typePuissancemécanique

Vitesse Intensité Rendement Facteur depuissance Couple Intensité

démarrageCoupledémarrage

Niveau debruit

Momentd'inertie Masse CESI Certificat Classe T

Motor Typ Leistung Drehzahl Strom Wirkungsgrad Leistungs-faktor Moment Anlauf-

stromAnlauf-moment

Schalldruck-pegel

Trägheits-moment Masse CESI Konformitäts-Bescheinigung Klasse T

Tipo de motorPotenciaproporcionada

Velocidad Corriente Rendimiento Factor depotencia Par Corriente de

arranquePar dearranque Nivel de ruido Momento

de inercia Peso Certificados CESI Clase T

Tipo motorePotenzaresa

Velocità Corrente Rendimento Fattorepotenza Coppia Corrente

avviamentoCoppiaavviamento Rumorosità Momento

d'inerzia Massa Certificato CESI Classe T

IIB IIC Pn[kW]

n[1/min]

In [A]

η[%]

cos ϕ Mn[Nm]

Ia/In Ma/Mn[dB(A)]

Lw LpJ[kgm2]

m[kg]

IIB IIC

Ex d Ex de Ex d Ex de standard standard

AB20 63 B 24 AB25 63 B 24 AC20 63 B 24 AC25 63 B 24 0.20 2740 0.52 68 0.83 0.7 3.5 2.6 60 52 0.0002 16 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 40.15 1310 0.59 49 0.74 1.1 2.2 1.5

AB20 71 A 24 AB25 71 A 24 AC20 71 A 24 AC25 71 A 24 0.30 2890 1.05 56 0.74 1.0 3.2 1.7 66 58 0.0006 19 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 40.20 1440 1.10 47 0.56 1.3 2.9 1.5




AB20 90 S 24 AB25 90 S 24 AC20 90 S 24 AC25 90 S 24 1.25 2780 2.90 65 0.96 4.3 5.4 2.0 77 69 0.0020 33 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 40.90 1380 2.40 64 0.85 6.2 4.6 1.8

AB20 90 L 24 AB25 90 L 24 AC20 90 L 24 AC25 90 L 24 1.60 2800 3.60 72 0.90 5.5 4.3 2.2 77 69 0.0026 33 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 41.20 1400 2.90 78 0.77 8.2 4.3 2.1

AB20 100 LA 24 AB25 100 LA 24 AC20 100 LA 24 AC25 100 LA 24 2.35 2780 5.40 70 0.90 8.1 6.4 2.4 80 72 0.0043 46 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 41.85 1400 4.50 72 0.82 12.6 5.4 2.1

AB20 100 LB 24 AB25 100 LB 24 AC20 100 LB 24 AC25 100 LB 24 3.00 2880 7.30 73 0.77 10.0 6.6 2.6 80 72 0.0053 46 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 42.40 1420 5.70 79 0.77 16.1 5.1 2.4

AB20 112 M 24 AB25 112 M 24 AC20 112 M 24 AC25 112M 24 4.00 2860 8.60 84 0.80 13.4 7.0 2.3 80 72 0.0103 65 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 43.30 1450 6.80 65 0.80 21.7 6.2 2.2


AB20 132 MB24 AB25 132 MB 24 AC20 132 MB 24 AC25 132MB 24 7.50 2880 14.50 88 0.85 24.9 8.9 2.2 83 75 0.0178 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 45.50 1430 13.50 73 0.80 36.8 7.1 2.1




AB20 180 M 24 AB25 180 M 24 AC20 180 M 24 AC25 180M 24 18.50 2930 36.00 82 0.90 60.3 6.4 2.1 83 74 0.1270 230 06 ATEX 074 Pending 06 ATEX 073 Pending 415.00 1460 29.50 83 0.88 98.1 5.6 2.0

AB20 180 L 24 AB25 180 L 24 AC20 180 L 24 AC25 180 L 24 22.00 2960 42.60 89 0.84 71.2 6.6 2.2 83 74 0.1488 245 06 ATEX 074 Pending 06 ATEX 073 Pending 418.50 1465 38.00 90 0.78 121.1 5.8 2.1

AB20 200 LB 24 AB25 200 LB 24 AC20 200 LB 24 AC25 200 LB 24 30.00 2970 54.60 90 0.88 97.3 7.0 2.3 87 77 0.2436 315 06 ATEX 074 Pending 06 ATEX 073 Pending 424.00 1480 44.60 93 0.84 156.5 6.4 2.3

AB20 225 S 24 AB25 225 S 24 AC20 225 S 24 AC25 225 S 24 33.00 2955 66.00 80 0.90 106.6 6.8 2.2 89 79 0.3762 355 06 ATEX 074 Pending 06 ATEX 073 Pending 430.00 1475 55.00 91 0.87 194.2 6.2 2.1



AB20 280 S 24 AB25 280 S 24 AC20 280 S 24 AC25 280 S 24 66.00 2950 123.30 91 0.85 200.7 9.4 2.8 88 76 0.5200 875 08 ATEX 012 --- 00 ATEX 053 01 ATEX 003X 452.00 1480 102.80 85 0.86 238.8 8.2 2.7

AB20 280 M 24 AB25 280 M 24 AC20 280 M 24 AC25 280 M 24 79.00 2950 145.90 91 0.86 242.8 9.2 2.8 88 76 0.6300 901 08 ATEX 012 --- 00 ATEX 053 01 ATEX 003X 460.00 1480 122.90 84 0.84 290.4 8.0 2.6



AB20 315 LA 24 AB25 315 LA 24 AC20 315 LA 24 AC25 315 LA 24 08 ATEX 021 --- 07 ATEX 073 --- 4

AB20 315 LB 24 AB25 315 LB 24 AC20 315 LB 24 AC25 315 LB 24 08 ATEX 021 --- 07 ATEX 073 --- 4

AB20 315 LC 24 AB25 315 LC 24 AC20 315 LC 24 AC25 315 LC 24 08 ATEX 021 --- 07 ATEX 073 --- 4

217216

2400 V50 Hz

30001500

ENGLISH

4.4.2

Three-phase motors

II 2GII 2GD

Speeds Rated data at direct on line start For general purpose (constant torque) - 1 winding Dahlander-connected rpm ENGLISH

FRANÇAIS Moteurs triphasés Vitesses Données nominales à démarrage direct Pour usage général (couple constant) - 1 enroulement couplage Dahlander tours/min FRANÇAIS

DEUTSCH Drehstrom Motoren Drehzahlen Betriebsdaten bei Direkteinschaltung Für allgemeinen Gebrauch (konstantes Gegenmoment) - 1 Wicklung / Schaltung Dahlander U/min DEUTSCH

ESPAÑOL Motores trifásicos Velocidades Datos nominales arranque directo Para uso general (par constante) - 1 devanado con conexión Dahlander rev/min ESPAÑOL

ITALIANO Motori trifase Velocità Dati nominali a avviamento diretto Per uso generale (coppia costante) - 1 avvolgimento collegamento Dahlander giri/min ITALIANO

Data not indicated is supplied on request - Les données qui ne sont pas indiquées sont fournies sur demande - Die nicht angegebenen Daten werden auf Anfrage geliefert -Los datos que no se han precisado se pueden comunicar cuando se solicite - I dati non indicati sono forniti su richiesta - - - - see the notes in section 4.1 - voir remarques dans la section 4.1 - siehe Anmerkung in Abschnitt 4.1 - véase notas en la sección 4.1 - vedi note di sezione 4.1








Niveau debruit



stromAnlauf-moment

Schalldruck-pegel










IIB IIC Pn[kW]

n[1/min]

In [A]

η[%]

cos ϕ Mn[Nm]

Ia/In Ma/Mn[dB(A)]

Lw LpJ[kgm2]

m[kg]

IIB IIC












AB20 132 MB 48 AB25 132 MB 48 AC20 132 MB 48 AC25 132MB 48 4.80 1410 10.50 77 0.86 32.5 5.3 1.8 75 67 0.0506 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 42.40 700 8.10 68 0.63 32.0 4.4 1.7

















219218

2400 V50 Hz

1500750

ENGLISH

4.4.2

Three-phase motors

II 2GII 2GD

Speeds Rated data at direct on line start For general purpose (constant torque) - 1 winding Dahlander-connected rpm ENGLISH

FRANÇAIS Moteurs triphasés Vitesses Données nominales à démarrage direct Pour usage général (couple constant) - 1 enroulement couplage Dahlander tours/min FRANÇAIS

DEUTSCH Drehstrom Motoren Drehzahlen Betriebsdaten bei Direkteinschaltung Für allgemeinen Gebrauch (konstantes Gegenmoment) - 1 Wicklung / Schaltung Dahlander U/min DEUTSCH

ESPAÑOL Motores trifásicos Velocidades Datos nominales arranque directo Para uso general (par constante) - 1 devanado con conexión Dahlander rev/min ESPAÑOL

ITALIANO Motori trifase Velocità Dati nominali a avviamento diretto Per uso generale (coppia costante) - 1 avvolgimento collegamento Dahlander giri/min ITALIANO


Data not indicated is supplied on request - Les données qui ne sont pas indiquées sont fournies sur demande - Die nicht angegebenen Daten werden auf Anfrage geliefert -Los datos que no se han precisado se pueden comunicar cuando se solicite - I dati non indicati sono forniti su richiesta








Niveau debruit



stromAnlauf-moment

Schalldruck-pegel










IIB IIC Pn[kW]

n[1/min]

In [A]

η[%]

cos ϕ Mn[Nm]

Ia/In Ma/Mn[dB(A)]

Lw LpJ[kgm2]

m[kg]

IIB IIC


221220

2400 V50 Hz

15001000

ENGLISH

4.4.2

Three-phase motors

II 2GII 2GD

Speeds Rated data at direct on line start For general purpose (constant torque) - 2 separate windings rpm ENGLISH

FRANÇAIS Moteurs triphasés Vitesses Données nominales à démarrage direct Pour usage général (couple constant) - 2 enroulements séparés tours/min FRANÇAIS

DEUTSCH Drehstrom Motoren Drehzahlen Betriebsdaten bei Direkteinschaltung Für allgemeinen Gebrauch (konstantes Gegenmoment) - 2 getrennte Wicklungen U/min DEUTSCH

ESPAÑOL Motores trifásicos Velocidades Datos nominales arranque directo Para uso general (par constante) - 2 devanados separados rev/min ESPAÑOL

ITALIANO Motori trifase Velocità Dati nominali a avviamento diretto Per uso generale (coppia costante) - 2 avvolgimenti separati giri/min ITALIANO








AB20 112 M 46 AB25 112 M 46 AC20 112 M 46 AC25 112 M 46 2.40 1420 5.20 79 0.84 16.1 6.5 1.8 68 60 0.0172 65 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 41.60 920 4.20 71 0.78 16.6 4.4 1.6


AB20 132 MA 46 AB25 132 MA 46 AC20 132 MA 46 AC25 132 MA 46 4.00 1460 9.40 79 0.78 26.2 6.2 2.0 75 67 0.0395 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 42.60 960 8.40 72 0.62 25.9 4.6 1.8

AB20 132 MB 46 AB25 132 MB 46 AC20 132 MB 46 AC25 132 MB 46 4.40 1450 10.50 76 0.80 29.0 6.4 2.0 75 67 0.0506 105 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 43.00 950 8.90 79 0.62 30.2 4.5 1.8




AB20 180 M 46 AB25 180 M 46 AC20 180 M 46 AC25 180 M 46 11.00 1470 21.50 88 0.84 71.5 6.6 2.0 79 70 0.2067 230 06 ATEX 074 Pending 06 ATEX 073 Pending 47.50 980 18.50 84 0.70 73.1 5.2 1.9


AB20 200 LA 46 AB25 200 LA 46 AC20 200 LA 46 AC25 200 LA 46 16.00 1480 33.50 82 0.84 103.2 6.7 2.1 82 72 0.2986 295 06 ATEX 074 Pending 06 ATEX 073 Pending 411.00 985 24.50 80 0.81 106.6 5.4 1.9












- - - - see the notes in section 4.1 - voir remarques dans la section 4.1 - siehe Anmerkung in Abschnitt 4.1 - véase notas en la sección 4.1 - vedi note di sezione 4.1








Niveau debruit



stromAnlauf-moment

Schalldruck-pegel










IIB IIC Pn[kW]

n[1/min]

In [A]

η[%]

cos ϕ Mn[Nm]

Ia/In Ma/Mn[dB(A)]

Lw LpJ[kgm2]

m[kg]

IIB IIC

Ex d Ex de Ex d Ex de










AB20 132 MA 68 AB25 132 MA68 AC20 132 MA 68 AC25 132 MA 68 2.55 965 6.80 75 0.72 25.2 4.2 1.8 68 60 0.0395 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 41.85 720 5.80 68 0.68 24.5 4.1 1.8

AB20 132 MB 68 AB25 132 MB68 AC20 132 MB 68 AC25 132 MB 68 3.00 970 7.40 79 0.74 29.5 5.4 1.9 68 60 0.0506 105 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 42.00 730 6.00 73 0.66 26.2 4.0 1.8

















223222

2400 V50 Hz

1000750

ENGLISH

4.4.2

Three-phase motors

II 2GII 2GD

Speeds Rated data at direct on line start For general purpose (constant torque) - 2 separate windings rpm ENGLISH

FRANÇAIS Moteurs triphasés Vitesses Données nominales à démarrage direct Pour usage général (couple constant) - 2 enroulements séparés tours/min FRANÇAIS

DEUTSCH Drehstrom Motoren Drehzahlen Betriebsdaten bei Direkteinschaltung Für allgemeinen Gebrauch (konstantes Gegenmoment) - 2 getrennte Wicklungen U/min DEUTSCH

ESPAÑOL Motores trifásicos Velocidades Datos nominales arranque directo Para uso general (par constante) - 2 devanados separados rev/min ESPAÑOL

ITALIANO Motori trifase Velocità Dati nominali a avviamento diretto Per uso generale (coppia costante) - 2 avvolgimenti separati giri/min ITALIANO









Niveau debruit



stromAnlauf-moment

Schalldruck-pegel










IIB IIC Pn[kW]

n[1/min]

In [A]

η[%]

cos ϕ Mn[Nm]

Ia/In Ma/Mn[dB(A)]

Lw LpJ[kgm2]

m[kg]

IIB IIC














AB40 132 ML 24 AB45 132 ML 24 AC40 132 ML 24 AC45 132ML 24 9.20 2910 17.50 90 0.84 30.2 6.9 2.3 83 75 0.0216 105 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 42.80 1440 5.70 87 0.82 18.6 6.6 2.2
















225224

2400 V50 Hz

30001500

ENGLISH

4.4.3

Three-phase motors

II 2GII 2GD

Speeds Rated data at direct on line start For centrifugal machines (quadratic torque) - 1 winding Dahlander-connected rpm ENGLISH

FRANÇAIS Moteurs triphasés Vitesses Données nominales à démarrage direct Pour machines centrifuges (couple quadratique) - 1 enroulement couplage Dahlander tours/min FRANÇAIS

DEUTSCH Drehstrom Motoren Drehzahlen Betriebsdaten bei Direkteinschaltung Für Zentrifugalmaschinen (quadratisches Gegenmoment) - 1 Wicklung / Schaltung Dahlander U/min DEUTSCH

ESPAÑOL Motores trifásicos Velocidades Datos nominales arranque directo Para máquinas centrífugas (par cuadrático) - 1 devanado con conexión Dahlander rev/min ESPAÑOL

ITALIANO Motori trifase Velocità Dati nominali a avviamento diretto Per macchine centrifughe (coppia quadratica) - 1 avvolgimento collegamento Dahlander giri/min ITALIANO









Niveau debruit



stromAnlauf-moment

Schalldruck-pegel










IIB IIC Pn[kW]

n[1/min]

In [A]

η[%]

cos ϕ Mn[Nm]

Ia/In Ma/Mn[dB(A)]

Lw LpJ[kgm2]

m[kg]

IIB IIC


227226

2400 V50 Hz

1500750

ENGLISH

4.4.3

Three-phase motors

II 2GII 2GD

Speeds Rated data at direct on line start For centrifugal machines (quadratic torque) - 1 winding Dahlander-connected rpm ENGLISH

FRANÇAIS Moteurs triphasés Vitesses Données nominales à démarrage direct Pour machines centrifuges (couple quadratique) - 1 enroulement couplage Dahlander tours/min FRANÇAIS

DEUTSCH Drehstrom Motoren Drehzahlen Betriebsdaten bei Direkteinschaltung Für Zentrifugalmaschinen (quadratisches Gegenmoment) - 1 Wicklung / Schaltung Dahlander U/min DEUTSCH

ESPAÑOL Motores trifásicos Velocidades Datos nominales arranque directo Para máquinas centrífugas (par cuadrático) - 1 devanado con conexión Dahlander rev/min ESPAÑOL

ITALIANO Motori trifase Velocità Dati nominali a avviamento diretto Per macchine centrifughe (coppia quadratica) - 1 avvolgimento collegamento Dahlander giri/min ITALIANO

Data not indicated is supplied on request - Les données qui ne sont pas indiquées sont fournies sur demande - Die nicht angegebenen Daten werden auf Anfrage geliefert -Los datos que no se han precisado se pueden comunicar cuando se solicite - I dati non indicati sono forniti su richiesta











AB40 132 MB 48 AB45 132 MB48 AC40 132 MB 48 AC45 132 MB48 5.90 1460 12.90 82 0.81 38.6 6.4 2.1 75 67 0.0324 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 41.50 710 5.30 69 0.61 20.4 4.0 1.7

























Niveau debruit



stromAnlauf-moment

Schalldruck-pegel










IIB IIC Pn[kW]

n[1/min]

In [A]

η[%]

cos ϕ Mn[Nm]

Ia/In Ma/Mn[dB(A)]

Lw LpJ[kgm2]

m[kg]

IIB IIC


229228










AB40 132 MA 46 AB45 132 MA 46 AC40 132 MA 46 AC45 132 MA 46 4.80 1455 11.50 75 0.80 31.5 6.9 1.9 75 67 0.0324 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 41.40 965 5.10 68 0.58 13.9 5.4 1.8

AB40 132 MB 46 AB45 132 MB 46 AC40 132 MB 46 AC45 132 MB 46 5.50 1460 13.00 76 0.80 36.0 5.7 1.9 75 67 0.0324 105 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 41.70 960 6.50 63 0.60 16.9 4.9 2.0


















2400 V50 Hz

15001000

ENGLISH

4.4.3

Three-phase motors

II 2GII 2GD

Speeds Rated data at direct on line start For centrifugal machines (quadratic torque) - 2 separate windings rpm ENGLISH

FRANÇAIS Moteurs triphasés Vitesses Données nominales à démarrage direct Pour machines centrifuges (couple quadratique) - 2 enroulements séparés tours/min FRANÇAIS

DEUTSCH Drehstrom Motoren Drehzahlen Betriebsdaten bei Direkteinschaltung Für Zentrifugalmaschinen (quadratisches Gegenmoment) - 2 getrennte Wicklungen U/min DEUTSCH

ESPAÑOL Motores trifásicos Velocidades Datos nominales arranque directo Para máquinas centrífugas (par cuadrático) - 2 devanados separados rev/min ESPAÑOL

ITALIANO Motori trifase Velocità Dati nominali a avviamento diretto Per macchine centrifughe (coppia quadratica) - 2 avvolgimenti separati giri/min ITALIANO









Niveau debruit



stromAnlauf-moment

Schalldruck-pegel










IIB IIC Pn[kW]

n[1/min]

In [A]

η[%]

cos ϕ Mn[Nm]

Ia/In Ma/Mn[dB(A)]

Lw LpJ[kgm2]

m[kg]

IIB IIC


AB4080 A 68 AB45 80 A 68 AC40 80 A 68 AC45 80 A 68 0.33 930 1.15 59 0.68 3.4 3.2 1.8 53 45 0.0027 26 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 40.09 700 0.64 33 0.51 1.2 2.0 1.4

AB4080 B 68 AB45 80 B 68 AC40 80 B 68 AC45 80 B 68 0.40 930 1.20 61 0.76 4.1 3.0 1.7 53 45 0.0027 26 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 40.12 680 0.65 44 0.63 1.7 2.1 1.3

AB4090 S 68 AB45 90 S 68 AC40 90 S 68 AC45 90 S 68 0.48 895 1.54 52 0.89 5.3 3.1 1.8 54 46 0.0034 33 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 40.19 705 0.82 52 0.65 2.6 2.2 1.4

AB4090 L 68 AB45 90 L 68 AC40 90 L 68 AC45 90 L 68 0.66 895 2.00 60 0.80 7.0 3.3 1.9 54 46 0.0049 33 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 40.25 700 1.20 51 0.59 3.4 2.4 1.6

AB40100 LA 68 AB45 100 LA 68 AC40 100 LA 68 AC45 100 LA 68 0.88 960 2.90 66 0.66 8.8 4.1 1.8 63 55 0.0088 46 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 40.37 715 1.80 47 0.63 4.9 3.6 1.7

AB40100 LB 68 AB45 100 LB 68 AC40 100 LB 68 AC45 100 LB 68 1.10 950 3.40 69 0.68 11.1 4.0 1.6 63 55 0.0088 46 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 40.44 710 2.10 49 0.62 5.9 3.5 1.4

AB40112 M 68 AB45 112 M 68 AC40 112 M 68 AC45 112M 68 1.50 970 4.60 74 0.64 14.8 4.5 2.0 65 57 0.0172 65 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 40.75 725 3.30 60 0.54 9.9 3.6 1.6

AB40132 S 68 AB45 132 S 68 AC40 132 S 68 AC45 132 S 68 2.20 950 5.70 75 0.74 22.1 4.5 2.2 68 60 0.0323 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 40.88 710 3.30 60 0.64 11.8 3.8 1.7

AB40132 MA 68 AB45 132 MA 68 AC40 132 MA 68 AC45 132MA68 3.00 960 7.00 76 0.81 29.8 4.9 2.0 68 60 0.0395 95 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 41.20 730 4.80 59 0.61 15.7 3.9 2.0

AB40132 MB 68 AB45 132 MB 68 AC40 132 MB 68 AC45 132MB68 3.70 965 8.90 79 0.76 36.6 5.1 2.2 68 60 0.0506 105 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 41.50 715 5.00 64 0.68 20.0 3.9 2.1

AB40160 M 68 AB45 160 M 68 AC40 160 M 68 AC45 160M 68 5.50 980 12.50 87 0.73 53.6 5.6 2.2 72 64 0.0919 180 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 42.50 730 6.80 83 0.64 32.7 4.3 2.3

AB40160 L 68 AB45 160 L 68 AC40 160 L 68 AC45 160 L 68 7.50 970 17.40 83 0.75 73.9 5.8 2.1 72 64 0.1218 195 02 ATEX 122 02 ATEX 124X 02 ATEX 123 02 ATEX 125X 44.00 728 11.60 78 0.64 52.8 4.0 2.0

AB40180 M 68 AB45 180 M 68 AC40 180 M 68 AC45 180M 68 9.00 965 20.00 83 0.78 89.1 5.8 2.3 76 67 0.2067 230 06 ATEX 074 Pending 06 ATEX 073 Pending 44.50 725 11.00 80 0.74 59.3 4.3 2.2

AB40180 L 68 AB45 180 L 68 AC40 180 L 68 AC45 180 L 68 10.00 960 23.50 79 0.78 99.5 5.6 2.1 76 67 0.2067 245 06 ATEX 074 Pending 06 ATEX 073 Pending 45.20 720 13.00 80 0.72 69.0 4.1 2.0

AB40200 LA 68 AB45 200 LA 68 AC40 200 LA 68 AC45 200 LA 68 13.00 970 29.50 81 0.79 128.0 5.3 2.0 79 69 0.2986 295 06 ATEX 074 Pending 06 ATEX 073 Pending 46.50 720 15.50 82 0.74 86.2 4.7 2.1

AB40200 LB 68 AB45 200 LB 68 AC40 200 LB 68 AC45 200 LB 68 16.00 970 36.00 80 0.80 157.5 5.2 1.9 79 69 0.3503 315 06 ATEX 074 Pending 06 ATEX 073 Pending 48.10 725 21.00 72 0.77 106.7 4.6 2.0

AB40225 S 68 AB45 225 S 68 AC40 225 S 68 AC45 225 S 68 20.00 980 41.00 88 0.80 194.9 5.0 2.3 81 70 0.6965 355 06 ATEX 074 Pending 06 ATEX 073 Pending 410.00 730 24.50 76 0.78 130.8 4.9 2.2



AB40280 S 68 AB45 280 S 68 AC40 280 S 68 AC45 280 S 68 40.00 985 81.40 91 0.78 387.8 7.3 3.1 77 65 1.1400 875 08 ATEX 012 --- 00 ATEX 053 01 ATEX 003X 416.00 740 38.20 84 0.72 206.5 5.3 2.7

AB40280 M 68 AB45 280 M 68 AC40 280 M 68 AC45 280 M 68 48.00 990 99.50 90 0.78 464.5 7.5 3.0 77 65 1.3600 901 08 ATEX 012 --- 00 ATEX 053 01 ATEX 003X 420.00 740 53.40 86 0.63 258.0 5.2 2.7

AB40315 S 68 AB45 315 S 68 AC40 315 S 68 AC45 315 S 68 58.00 990 119.60 91 0.77 559.5 7.9 3.4 79 65 1.6300 971 08 ATEX 012 --- 00 ATEX 053 01 ATEX 003X 424.00 742 56.90 87 0.70 308.9 5.4 2.9

AB40315 M 68 AB45 315 M 68 AC40 315 M 68 AC45 315 M 68 65.00 995 130.90 92 0.78 623.9 7.8 3.3 79 65 1.8300 884 08 ATEX 012 --- 00 ATEX 053 01 ATEX 003X 427.00 740 62.30 87 0.72 348.4 5.3 2.9

AB40315 LA 68 AB45 315 LA 68 AC40 315 LA 68 AC45 315 LA 68 08 ATEX 021 --- 07 ATEX 073 --- 4

AB40315 LB 68 AB45 315 LB 68 AC40 315 LB 68 AC45 315 LB 68 08 ATEX 021 --- 07 ATEX 073 --- 4

AB40315 LC 68 AB45 315 LC 68 AC40 315 LC 68 AC45 315 LC 68 08 ATEX 021 --- 07 ATEX 073 --- 4

231230

2400 V50 Hz

1000750

ENGLISH

4.4.3

Three-phase motors

II 2GII 2GD

Speeds Rated data at direct on line start For centrifugal machines (quadratic torque) - 2 separate windings rpm ENGLISH

FRANÇAIS Moteurs triphasés Vitesses Données nominales à démarrage direct Pour machines centrifuges (couple quadratique) - 2 enroulements séparés tours/min FRANÇAIS

DEUTSCH Drehstrom Motoren Drehzahlen Betriebsdaten bei Direkteinschaltung Für Zentrifugalmaschinen (quadratisches Gegenmoment) - 2 getrennte Wicklungen U/min DEUTSCH

ESPAÑOL Motores trifásicos Velocidades Datos nominales arranque directo Para máquinas centrífugas (par cuadrático) - 2 devanados separados rev/min ESPAÑOL

ITALIANO Motori trifase Velocità Dati nominali a avviamento diretto Per macchine centrifughe (coppia quadratica) - 2 avvolgimenti separati giri/min ITALIANO


233232

Motor type Rated Speed Current Efficiency Power Torque Starting Starting Capacitor Sound Moment of Mass CESI Certificates Class Toutput factor current torque pressure inertia

Moteur type Puissance Vitesse Intensité Rendement Facteur de Couple Intensité Couple Conden- Pression Moment Masse CESI Certificat Classe Tmécanique puissance démarrage démarrage sateur sonore d'inertie

Motor Typ Leistung Drehzahl Strom Wirkungsgrad Leistungs- Moment Anlauf- Anlauf- Konden- Geräusch- Trägheits- Masse CESI Konformitäts-Bescheinigung Klasse Tfaktor strom moment sator werte moment

Tipo de motor Potencia Velocidad Corriente Rendimiento Factor de Par Corriente de Par de Conden- Presión Momento Peso Certificados CESI Clase Tproporcionada potencia arranque arranque sador acústica de inercia

Tipo motore Potenza Velocità Corrente Rendimento Fattore Coppia Corrente Coppia Conden- Pressione Momento Massa Certificato CESI Classe Tresa potenza avviamento avviamento satore sonora d'inerzia

IIB IIC Pn n In η cos ϕ Mn Ia/In Ma/Mn C [dB(A)] J m IIB IIC

Ex d Ex de Ex d Ex de [kW] [1/min] [A] [%] [Nm] [µF] Lw Lp [kgm2] [kg] standard standard

AB10 63 A 2 AB15 63 A 2 AC10 63 A 2 AC15 63 A 2 0.10 2750 1.30 35 0.95 0.3 3.3 0.6 6.3 60 52 0.0001 16 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4

AB10 63 B 2 AB15 63 B 2 AC10 63 B 2 AC15 63 B 2 0.15 2750 1.30 53 0.95 0.5 3.8 0.6 8.0 60 52 0.0001 16 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4





AB10 90 S 2 AB15 90 S 2 AC10 90 S 2 AC15 90 S 2 1.10 2750 7.80 63 0.97 3.8 4.4 0.7 45.0 77 69 0.0012 33 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4

AB10 90 L 2 AB15 90 L 2 AC10 90 L 2 AC15 90 L 2 1.50 2800 8.90 74 0.98 5.1 4.9 0.7 60.0 77 69 0.0015 33 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4

AB10 100 LA 2 AB15 100 LA 2 AC10 100 LA 2 AC15 100 LA 2 2.20 2800 15.50 65 0.95 7.5 5.0 0.6 60.0 80 72 0.0029 46 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4

AB10 100 LB 2 AB15 100 LB 2 AC10 100 LB 2 AC15 100 LB 2 3.00 2800 18.00 74 0.98 10.2 5.0 0.6 80.0 80 72 0.0036 46 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4










AB10 100 LA 4 AB15 100 LA 4 AC10 100 LA 4 AC15 100 LA 4 1.30 1370 8.10 72 0.98 9.0 3.2 0.5 35.0 63 55 0.0043 46 01 ATEX 102 02 ATEX 044X 01 ATEX 103 02 ATEX 045X 4










1230 V50 Hz

300015001000

ENGLISH

4.4.4

Single-phase motors

II 2GII 2GD


FRANÇAIS Moteurs monophasé Vitesse Données nominales à démarrage direct tours/min FRANÇAIS

DEUTSCH Einphasen Motoren Drehzahl Betriebsdaten bei Direkteinschaltung U/min DEUTSCH

ESPAÑOL Motores monofásicos Velocidad Datos nominales arranque directo rev/min ESPAÑOL

ITALIANO Motori monofase Velocità Dati nominali a avviamento diretto giri/min ITALIANO

400 V, 50 Hz

[1/min] 3000

[Hz] 5 ÷ 50range 1 ÷ 10

[1/min] 300 ÷ 3000

[Hz] 10 ÷ 50range 1 ÷ 5

[1/min] 600 ÷ 3000

[Hz] 25 ÷ 50range 1 ÷ 2

[1/min] 1500 ÷ 3000

[Hz] 50 ÷ 87range 10 ÷ 17

[1/min] 3000 ÷ 5200

[Hz] 50 ÷ 87range 10 ÷ 17

[1/min] 3000 ÷ 5200

[Hz] 5 ÷ 50range 1 ÷ 10

[1/min] 300 ÷ 3000

[Hz] 5 ÷ 50range 1 ÷ 10

[1/min] 300 ÷ 3000

Motor typeMainsconnection

Constant torque Constant torque Constant torqueConstant torque -Weakened flux

Constant torque -Constant flux ∆ connection

Constant torque -Forced Ventilation

Quadratic torque Class T

Moteur typeAlimentationde secteur

Couple constant Couple constant Couple constantCouple constant -Flux affaibli

Couple constant -Flux constant raccordement ∆

Couple constant -Ventilation Assistée

Couple quadratique Classe T

Motor Typ NetzeinspeisungKonstantesGegenmoment

KonstantesGegenmoment


Konstantes Gegenmoment -Feldschwächbetrieb

Konstantes Gegenmoment -konstanter Strom ∆-Verbindung

Konstantes Gegenmoment -Fremdbelüftung

Quadratisches Gegenmoment Klasse T

Tipo de motorAlimentacióndesde la red

Par constante Par constante Par constantePar constante -Flujo debilitado

Par constante -Flujo constante conexión ∆

Par constante -Ventilación asistida

Par cuadrático Clase T

Tipo motore Alimentazioneda rete Coppia costante Coppia costante Coppia costante

Coppia costante-Flusso indebolito

Coppia costante -Flusso costante collegamento ∆

Coppia costante -Ventilazione Assistita

Coppia quadratica Classe T

IIB IIC Pn[kW]

In[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A] B


AB70 63 B 2 AB75 63 B 2 AC70 63 B 2 AC75 63 B 2 0.25 0.85 0.02-0.16 0.54 0.53 0.04-0.18 0.61 0.60 0.11-0.22 0.76 0.74 0.13-0.23 0.46 0.44 0.21-0.36 0.70 1.18 --- --- --- 0.25 0.85 0.83 4

AB70 71 A 2AB70 71 B 2

AB75 71 A 2AB75 71 B 2

AC70 71 A 2AC70 71 B 2

AC75 71 A 2AC75 71 B 2

0.370.55

1.101.40

0.02-0.240.04-0.35

0.811.19

0.710.91

0.05-0.270.08-0.40

0.911.34

0.801.02

0.16-0.330.24-0.49

1.121.65

0.991.26

0.20-0.350.30-0.51

0.681.00

0.600.76

0.30-0.530.45-0.79

1.041.53

1.602.02

------

------

------

0.370.55

1.261.86

1.121.42

44

AB70 80 A 2AB70 80 B 2

AB75 80 A 2AB75 80 B 2

AC70 80 A 2AC70 80 B 2

AC75 80 A 2AC75 80 B 2

0.751.10

1.902.60

0.05-0.480.07-0.70

1.642.38

1.291.67

0.11-0.540.16-0.79

1.842.67

1.451.88

0.33-0.670.49-0.98

2.283.31

1.802.32

0.40-0.700.59-1.03

1.371.99

1.081.40

0.62-1.070.90-1.57

2.103.05

2.893.73

------

------

------

0.751.10

2.563.71

2.022.61

44

AB70 90 S 2AB70 90 L 2

AB75 90 S 2AB75 90 L 2

AC70 90 S 2AC70 90 L 2

AC75 90 S 2AC75 90 L 2

1.502.20

3.104.80

0.10-0.960.14-1.41

3.194.77

1.993.08

0.22-1.080.32-1.58

3.595.36

2.243.47

0.67-1.340.98-1.96

4.456.64

2.784.29

0.81-1.401.18-2.06

2.684.00

1.672.59

1.23-2.141.81-3.15

4.106.12

4.456.88

------

------

------

1.502.20

4.997.45

3.124.82

44

AB70 100 LA 2 AB75 100 LA 2 AC70 100 LA 2 AC75 100 LA 2 3.00 7.30 0.19-1.92 6.41 4.67 0.43-2.16 7.21 5.26 1.34-2.67 8.93 6.51 1.61-2.80 5.38 3.92 2.47-4.29 8.23 10.44 0.27-2.70 9.02 6.57 3.00 10.02 7.30 4

[Hz] 50 ÷ 70range 10 ÷ 14

[1/min] 3000 ÷ 4200

[Hz] 50 ÷ 70range 10 ÷ 14

[1/min] 3000 ÷ 4200

AB70 112 M 2 AB70 112 M 2 AC70 112 M 2 AC75 112 M 2 4.00 8.70 0.30-2.60 8.40 5.60 0.60-2.90 9.50 6.30 1.80-3.60 11.70 7.80 3.00-4.10 9.80 6.50 3.90-5.40 12.80 14.90 0.40-3.60 11.90 7.90 4.00 13.20 8.80 4

AB70 132 SA 2AB70 132 SB 2AB70 132 MB2

AB75 132 SA 2AB75 132 SB 2AB75 132 MB 2

AC70 132 SA 2AC70 132 SB 2AC70 132 MB2

AC75 132 SA 2AC75 132 SB 2AC75 132 MB 2

5.507.509.20

12.0015.0018.00

0.40-3.500.50-4.800.60-5.90

11.6015.8019.40

7.409.6011.50

0.80-4.001.10-5.401.30-6.60

13.1017.7021.80

8.3010.8013.00

2.50-4.903.30-6.704.10-8.20

16.2021.9027.00

10.3013.4016.10

4.10-5.705.60-7.806.80-9.50

13.5018.2022.40

8.6011.1013.40

5.30-7.507.30-10.208.90-12.50

17.6023.9029.40

19.5025.3030.40

0.50-5.000.70-6.800.80-8.30

16.4022.2027.30

10.4013.5016.20

5.507.509.20

18.2024.6030.30

11.6015.0018.00

444

AB70 160 MA2AB70 160 MB2AB70 160 L 2

AB75 160 MA 2AB75 160 MB 2AB75 160 L 2

AC70 160 MA2AC70 160 MB2AC70 160 L 2

AC75 160 MA 2AC75 160 MB 2AC75 160 L 2

11.0015.0018.50

20.6026.8032.80

0.70-7.001.00-9.601.20-11.80

23.0031.1038.40

13.1016.9020.90

1.60-7.902.20-10.802.70-13.30

25.8035.0043.20

14.8019.0023.50

4.90-9.806.70-13.408.20-16.50

32.0043.3053.50

18.3023.6029.00

8.10-11.4011.10-15.5013.70-19.20

26.5036.0044.40

15.2019.6024.10

10.70-14.9014.60-20.4017.90-25.10

34.8047.2058.20

34.6044.6055.00

1.00-9.901.40-13.501.70-16.70

32.3043.8054.00

18.5023.8029.30

11.0015.0018.50

35.9048.6060.00

20.5026.4032.60

444

[Hz] 50 ÷ 60range 10 ÷ 12

[1/min] 3000 ÷ 3600

[Hz] 50 ÷ 60range 10 ÷ 12

[1/min] 3000 ÷ 3600

AB70 180 M 2 AB75 180 M 2 AC70 180 M 2 AC75 180 M 2 22.00 40.00 1.40-14.10 46.00 25.40 3.20-15.80 51.00 28.50 9.80-19.60 63.00 35.30 19.80-23.80 64.00 35.70 22.00-26.40 71.00 68.90 2.00-19.80 64.00 35.70 22.00 71.00 39.60 4

AB70 200 LA 2AB70 200 LB 2

AB75 200 LA 2AB75 200 LB 2

AC70 200 LA 2AC70 200 LB 2

AC75 200 LA 2AC75 200 LB 2

30.0037.00

55.0067.00

1.90-19.202.40-23.70

62.0076.00

35.2042.40

4.30-21.605.30-26.60

69.0086.00

39.6047.70

13.40-26.7016.50-33.00

86.00106.00

49.0059.00

27.00-32.4033.30-40.00

87.00107.00

49.5059.60

30.00-36.0037.00-44.40

96.00119.00

95.70115.20

2.70-27.003.30-33.30

87.00107.00

49.5059.60

30.0037.00

96.00119.00

55.0066.30

44

AB70 225 M 2 AB75 225 M 2 AC70 225 M 2 AC75 225 M 2 45.00 82.00 2.90-28.80 92.00 52.00 6.50-32.40 104.00 58.50 20.00-40.10 129.00 72.30 40.50-48.60 130.00 73.10 42.70-51.30 137.00 134.20 4.10-40.50 130.00 73.10 45.00 144.00 81.20 4

AB70 250 M 2 AB75 250 M 2 AC70 250 M 2 AC75 250 M 2 55.00 98.00 3.50-35.20 113.00 62.80 7.90-39.60 127.00 70.60 24.50-49.00 157.00 87.40 49.50-59.40 159.00 88.30 52.20-62.70 168.00 162.10 5.00-49.50 159.00 88.30 55.00 176.00 98.10 4

AB70 280 S 2AB70 280 M 2

AB75 280 S 2AB75 280 M 2

AC70 280 S 2AC70 280 M 2

AC75 280 S 2AC75 280 M 2

75.0090.00

132.00165.00

4.60-46.405.60-55.60

149.00178.00

81.00101.40

10.10-50.7012.20-60.80

163.00195.00

88.50110.90

31.70-63.4038.00-76.10

203.00244.00

110.70138.70

63.70-76.5076.50-91.80

204.00245.00

111.30139.40

67.50-81.0081.00-97.20

216.00259.00

205.00256.70

6.40-63.707.70-76.50

204.00245.00

111.30139.40

73.5087.30

240.00288.00

131.00164.00

44

AB70 315 S 2AB70 315 LA 2AB70 315 LB 2AB70 315 LC 2


AC70 315 S 2AC70 315 LA 2AC70 315 LB 2AC70 315 LC 2


110.00132.00160.00200.00

139.00222.00269.00332.00

6.80-68.008.20-81.609.90-98.90

12.40-123.60

218.00262.00317.00396.00

118.50140.70166.00206.00

14.90-74.4017.90-89.2021.60-108.2027.00-135.20

238.00287.00346.00433.00

129.60153.90181.50225.30

46.50-91.0055.80-111.6067.60-135.3084.50-169.10

298.00359.00433.00541.00

162.10192.40227.00281.70

93.50-112.20112.20-134.60136.00-163.20170.00-204.00

300.00361.00435.00544.00

163.00193.40228.20283.20

99.00-118.80118.80-142.50144.00-172.80180.00-216.00

317.00382.00461.00576.00

300.10356.20420.30521.50

9.40-93.5011.20-112.2013.60-136.0017.00-170.00

300.00361.00435.00544.00

163.00193.40228.20283.00

105.60124.10147.20180.00

353.00424.00512.00640.00

191.80227.60268.60333.20

4444

234 235

B Rounded values To reduce noise level, IC 416 is advisable (available from frame size 100) Higher frequency upon request Values refer to 50 Hz Same certificates as section 4.1 T3 upon request;Valeurs arrondies On conseille IC 416 pour réduire le bruit (disponible à partir de hauteur d’axe 100) Fréquence supérieure sur demande Valeurs se réfèrent à 50 Hz Mêmes certificats que ceux de la section 4.1 T3 sur demande;Gerundete Werte Zur Lärmverringerung wird IC 416 empfohlen (verfügbar ab Baugröße 100) Auf Anfrage höhere Frequenz Werte beziehen sich auf 50 Hz Gleiche Bescheinigungen wie in Abschnitt 4.1 T3 auf Wunsch;Valores redondeado Se aconseja IC 416 para reducir el nivel de ruido (disponible a partir de altura del eje 100) Frecuencia mayor a petición del cliente Valores se refieren a 50 Hz Los mismos certificados que en la sección 4.1 T3 según demanda;Valori arrotondati Si consiglia IC 416 per ridurre il rumore (disponibile da altezza d'asse 100) Frequenza superiore su richiesta Valori riferiti a 50 Hz Stessi certificati della sezione 4.1 T3 a richiesta;

ENGLISH

4.4.5

Motors energized by inverter

II 2GII 2GD

Self-ventilated IC 411 Self-ventilated IC 411 or forced ventilation IC 416 Forced ventilation IC 416 Self-ventilated IC 411

2

Pole ENGLISH

FRANÇAIS Moteurs alimentés par variateur Autoventilés IC 411 Autoventilés IC 411 ou ventilation assistée IC 416 Ventilation assistée IC 416 Autoventilés IC 411 Pôles FRANÇAIS

DEUTSCH Motoren mit Umrichterversorgung Eigenbelüftet IC 411 Eigenbelüftet IC 411 oder fremdbelüftet IC 416 Fremdbelüftung IC 416 Eigenbelüftet IC 411 Pole DEUTSCH

ESPAÑOL Motores alimentados con inverter Autoventilados IC 411 Autoventilados IC 411 o ventilación asistida IC 416 Ventilación asistida IC 416 Autoventilados IC 411 Polos ESPAÑOL

ITALIANO Motori alimentati da inverter Autoventilati IC 411 Autoventilati IC 411 o ventilazione assistita IC 416 Ventilazione assistita IC 416 Autoventilati IC 411 Poli ITALIANO

237236

ENGLISH

4.4.5


II 2GII 2GD


4

Pole ENGLISH





400 V, 50 Hz

[1/min] 1500

[Hz] 5 ÷ 50range 1 ÷ 10

[1/min] 150 ÷ 1500

[Hz] 10 ÷ 50range 1 ÷ 5

[1/min] 300 ÷ 1500

[Hz] 25 ÷ 50range 1 ÷ 2

[1/min] 750 ÷ 1500

[Hz] 50 ÷ 87range 10 ÷ 17

[1/min] 1500 ÷ 2600

[Hz] 50 ÷ 87range 10 ÷ 17

[1/min] 1500 ÷ 2600

[Hz] 5 ÷ 50range 1 ÷ 10

[1/min] 150 ÷ 1500

[Hz] 5 ÷ 50range 1 ÷ 10

[1/min] 150 ÷ 1500
























Coppia costante -Flusso indebolito


Coppia costante-Ventilazione Assistita


IIB IIC Pn[kW]

In[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A] B


AB70 63 A 4AB70 63 B 4

AB75 63 A 4AB75 63 B 4

AC70 63 A 4AC70 63 B 4

AC75 63 A 4AC75 63 B 4

0.120.18

0.620.67

0.01-0.080.01-0.12

0.530.82

0.340.44

0.02-0.090.03-0.13

0.600.92

0.380.49

0.05-0.110.08-0.16

0.741.14

0.480.61

0.06-0.110.10-0.17

0.450.69

0.290.37

0.10-0.170.15-0.26

0.681.05

0.760.97

------

------

------

0.120.18

0.831.28

0.530.68

44

AB70 71 A 4AB70 71 B 4

AB75 71 A 4AB75 71 B 4

AC70 71 A 4AC70 71 B 4

AC75 71 A 4AC75 71 B 4

0.250.37

0.801.10

0.02-0.160.02-0.24

1.111.63

0.490.69

0.04-0.180.05-0.27

1.251.83

0.560.77

0.11-0.220.16-0.33

1.552.26

0.690.96

0.13-0.230.20-0.35

0.931.37

0.410.58

0.21-0.360.30-0.53

1.432.09

1.101.54

------

------

------

0.250.37

1.742.54

0.771.07

44

AB70 80 A 4AB70 80 B 4

AB75 80 A 4AB75 80 B 4

AC70 80 A 4AC70 80 B 4

AC75 80 A 4AC75 80 B 4

0.550.75

1.602.00

0.04-0.350.05-0.48

2.443.27

1.041.29

0.08-0.400.11-0.54

2.743.68

1.171.45

0.24-0.490.33-0.67

3.394.56

1.441.79

0.30-0.510.40-0.70

2.042.75

0.871.08

0.45-0.790.62-1.07

3.134.21

2.322.87

------

------

------

0.550.75

3.815.12

1.622.01

44

AB70 90 S 4AB70 90 L 4

AB75 90 S 4AB75 90 L 4

AC70 90 S 4AC70 90 L 4

AC75 90 S 4AC75 90 L 4

1.101.50

2.803.60

0.07-0.700.10-0.96

4.806.46

1.752.31

0.16-0.790.22-1.08

5.407.26

1.972.60

0.49-0.980.67-1.34

6.698.99

2.433.21

0.59-1.030.81-1.40

4.035.42

1.471.94

0.90-1.571.23-2.14

6.178.29

3.915.15

------

------

------

1.101.50

7.5010.09

2.733.61

44

AB70 100 LA 4AB70 100 LB 4

AB75 100 LA 4AB75 100 LB 4

AC70 100 LA 4AC70 100 LB 4

AC75 100 LA 4AC75 100 LB 4

2.203.00

5.256.83

0.14-1.410.19-1.92

9.4212.77

3.344.34

0.32-1.580.43-2.16

10.6014.36

3.764.88

0.98-1.961.34-2.67

13.1217.78

4.656.04

1.18-2.061.61-2.80

7.9110.71

2.803.64

1.81-3.152.47-4.29

12.1016.40

7.469.68

0.20-1.980.27-2.70

13.2517.96

4.706.10

2.203.00

14.7219.95

5.226.78

44

AB70 112 M 4 AB75 112 M 4 AC70 112 M 4 AC75 112 M 4 4.00 8.20 0.30-2.60 17.00 5.10 0.60-2.90 19.10 5.80 1.80-3.60 23.60 7.20 2.20-3.70 14.30 4.30 3.30-5.70 21.80 11.50 0.40-3.60 23.90 7.20 4.00 26.50 8.00 4

AB70 132 SB 4AB70 132 MB4AB70 132 ML 4

AB75 132 SB 4AB75 132 MB 4AB75 132 ML 4

AC70 132 SB 4AC70 132 MB4AC70 132 ML 4

AC75 132 SB 4AC75 132 MB 4AC75 132 ML 4

5.507.508.80

11.6016.5018.50

0.40-3.500.50-4.800.60-5.60

23.1031.6037.00

7.4010.5011.80

0.80-4.001.10-5.401.30-6.30

26.0035.6041.60

8.3011.8013.30

2.50-4.903.30-6.703.90-7.80

32.2044.0051.50

10.3014.6016.50

3.00-5.104.00-7.004.70-8.20

19.4026.5031.00

6.208.809.90

4.50-7.906.20-10.707.20-12.60

29.7040.6047.50

16.5023.3026.40

0.50-5.000.70-6.800.80-7.90

32.5044.5052.00

10.4014.7016.60

5.507.508.80

36.1049.4057.80

11.6016.3018.50

444

AB70 160 MB4AB70 160 L 4

AB75 160 MB 4AB75 160 L 4

AC70 160 MB4AC70 160 L 4

AC75 160 MB 4AC75 160 L 4

11.0015.00

23.0030.00

0.70-7.001.00-9.60

45.7062.40

14.6019.10

1.60-7.902.20-10.80

51.5070.20

16.5021.50

4.90-9.806.70-13.40

63.7086.80

20.4026.70

5.90-10.308.10-14.00

38.4052.30

12.3016.10

9.00-15.7012.30-21.50

58.7080.10

32.7042.80

1.00-9.901.40-13.50

64.3087.70

20.6026.90

11.0015.00

71.5097.50

22.9029.90

44

AB70 180 M 4AB70 180 L 4

AB75 180 M 4AB75 180 L 4

AC70 180 M 4AC70 180 L 4

AC75 180 M 4AC75 180 L 4

18.5022.00

39.0044.00

1.20-11.801.40-14.10

77.0092.00

25.0028.30

2.70-13.303.20-15.80

87.00103.00

28.2031.90

8.20-16.509.80-19.60

107.00127.00

34.9039.40

9.90-17.3011.80-20.60

65.0077.00

21.0023.80

15.20-26.5018.10-31.50

99.00118.00

55.9063.30

1.70-16.702.00-19.80

108.00129.00

35.2039.80

18.5022.00

120.20143.00

39.1044.30

44

AB70 200 LB 4 AB75 200 LB 4 AC70 200 LB 4 AC75 200 LB 4 30.00 54.00 1.90-19.20 124.00 34.30 4.30-21.60 140.00 38.60 13.40-26.70 173.00 47.80 16.10-28.00 104.00 28.80 24.70-42.90 160.00 76.60 2.70-27.00 175.00 48.30 30.00 194.00 53.60 4

AB70 225 S 4AB70 225 M 4

AB75 225 S 4AB75 225 M 4

AC70 225 S 4AC70 225 M 4

AC75 225 S 4AC75 225 M 4

37.0045.00

70.0082.00

2.40-23.702.90-28.80

153.00186.00

44.6052.70

5.30-26.606.50-32.40

172.00209.00

50.2059.30

16.50-33.0020.00-40.10

213.00259.00

62.2073.40

19.90-34.6024.20-42.00

128.00156.00

37.5044.20

28.90-50.3035.10-61.10

186.00227.00

94.70111.90

3.30-33.304.10-40.50

215.00261.00

62.8074.10

37.0045.00

239.00290.00

69.8082.40

44

AB70 250 M 4 AB75 250 M 4 AC70 250 M 4 AC75 250 M 4 55.00 96.00 3.50-35.20 226.00 61.40 7.90-39.60 255.00 69.10 24.50-49.00 315.00 85.50 29.50-51.40 190.00 51.50 42.90-74.70 276.00 130.30 5.00-49.50 318.00 86.40 55.00 354.00 96.00 4

AB70 280 S 4AB70 280 M 4

AB75 280 S 4AB75 280 M 4

AC70 280 S 4AC70 280 M 4

AC75 280 S 4AC75 280 M 4

75.0090.00

136.00163.00

4.80-48.005.80-57.60

310.00370.00

86.60103.90

10.50-52.5012.60-63.00

339.00405.00

94.70113.70

32.20-64.5038.70-77.40

416.00498.00

116.40139.70

33.70-58.7040.50-70.50

218.00261.00

60.9073.10

58.60-101.9070.30-122.30

378.00452.00

183.80220.50

6.60-66.007.90-79.20

426.00509.00

119.10142.90

75.0090.00

484.00579.00

135.40162.40

44





110.00132.00160.00200.00

199.00239.00282.00354.00

7.00-70.408.50-84.50

10.20-102.4012.80-128.00

453.00543.00657.00822.00

127.20154.20179.90225.60

15.40-77.0018.50-92.4022.40-112.0028.00-140.00

495.00594.00719.00899.00

139.10168.70196.80246.80

47.30-94.6056.80-113.5068.80-137.6086.00-172.00

608.00730.00883.001104.00

170.90207.20241.80303.20

49.50-86.1059.40-103.3072.00-125.3090.00-156.60

318.00382.00462.00578.00

89.40108.40126.50158.60

85.90-149.40103.10-179.30124.90-217.40156.20-271.70

552.00663.00802.001002.00

269.80327.30381.80478.80

9.70-96.8011.60-116.1014.10-140.8017.60-176.00

623.00747.00904.001130.00

174.80212.10247.40310.20

110.00132.00160.00200.00

707.00849.001027.001284.00

198.70241.00281.20352.60

4444

B Rounded values Values refer to 50 Hz Same certificates as section 4.1 T3 upon request;Valeurs arrondies Valeurs se réfèrent à 50 Hz Mêmes certificats que ceux de la section 4.1 T3 sur demande;Gerundete Werte Werte beziehen sich auf 50 Hz Gleiche Bescheinigungen wie in Abschnitt 4.1 T3 auf Wunsch;Valores redondeado Valores se refieren a 50 Hz Los mismos certificados que en la sección 4.1 T3 según demanda;Valori arrotondati Valori riferiti a 50 Hz Stessi certificati della sezione 4.1 T3 a richiesta;

239238

400 V, 50 Hz

[1/min] 1000

[Hz] 5 ÷ 50range 1 ÷ 10

[1/min] 100 ÷ 1000

[Hz] 10 ÷ 50range 1 ÷ 5

[1/min] 200 ÷ 1000

[Hz] 25 ÷ 50range 1 ÷ 2

[1/min] 500 ÷ 1000

[Hz] 50 ÷ 87range 10 ÷ 17

[1/min] 1000 ÷ 1750

[Hz] 50 ÷ 87range 10 ÷ 17

[1/min] 1000 ÷ 1750

[Hz] 5 ÷ 50range 1 ÷ 10

[1/min] 100 ÷ 1000

[Hz] 5 ÷ 50range 1 ÷ 10

[1/min] 100 ÷ 1000




























IIB IIC Pn[kW]

In[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A] B


AB70 63 B 6 AB75 63 B 6 AC70 63 B 6 AC75 63 B 6 0.09 0.65 0.01-0.06 0.65 0.42 0.01-0.06 0.73 0.47 0.04-0.08 0.90 0.59 0.05-0.08 0.54 0.35 0.07-0.13 0.83 0.94 --- --- --- 0.09 1.01 0.66 4

AB70 71 A 6AB70 71 B 6

AB75 71 A 6AB75 71 B 6

AC70 71 A 6AC70 71 B 6

AC75 71 A 6AC75 71 B 6

0.180.26

0.921.00

0.01-0.120.02-0.17

1.181.73

0.700.64

0.03-0.130.04-0.19

1.331.95

0.790.71

0.08-0.160.12-0.23

1.652.41

0.970.88

0.10-0.170.14-0.24

0.991.45

0.590.53

0.15-0.260.21-0.37

1.522.22

1.561.42

------

------

------

0.180.26

1.852.70

1.090.99

44

AB70 80 A 6AB70 80 B 6

AB75 80 A 6AB75 80 B 6

AC70 80 A 6AC70 80 B 6

AC75 80 A 6AC75 80 B 6

0.370.55

1.601.80

0.02-0.240.04-0.35

2.433.61

1.021.12

0.05-0.270.08-0.40

2.744.07

1.141.26

0.16-0.330.24-0.49

3.395.03

1.411.55

0.20-0.350.30-0.51

2.043.03

0.850.94

0.30-0.530.45-0.79

3.124.64

2.272.49

------

------

------

0.370.55

3.805.65

1.591.74

44

AB70 90 S 6AB70 90 L 6

AB75 90 S 6AB75 90 L 6

AC70 90 S 6AC70 90 L 6

AC75 90 S 6AC75 90 L 6

0.751.10

2.203.20

0.05-0.480.07-0.70

5.047.19

1.392.00

0.11-0.540.16-0.79

5.678.09

1.572.25

0.33-0.670.49-0.98

7.0110.01

1.942.79

0.40-0.700.59-1.03

4.236.03

1.171.68

0.62-1.070.90-1.57

6.479.24

3.114.47

------

------

------

0.751.10

7.8711.24

2.183.13

44


AB70 112 M 6 AB75 112 M 6 AC70 112 M 6 AC75 112 M 6 2.20 6.20 0.10-1.40 14.00 3.90 0.30-1.60 15.80 4.40 1.00-2.00 19.50 5.40 1.20-2.10 11.80 3.30 1.80-3.20 18.00 8.70 0.20-2.00 19.70 5.50 2.20 21.90 6.10 4

AB70 132 S 6AB70 132 M 6AB70 132 ML 6

AB75 132 S 6AB75 132 M 6AB75 132 ML 6

AC70 132 S 6AC70 132 M 6AC70 132 ML 6

AC75 132 S 6AC75 132 M 6AC75 132 ML 6

3.004.005.50

8.509.5012.00

0.20-1.900.30-2.600.40-3.50

19.3025.2035.00

5.406.107.70

0.40-2.200.60-2.900.80-4.00

21.7028.4039.40

6.106.808.60

1.30-2.701.80-3.602.50-4.90

26.9035.1048.80

7.608.5010.70

1.60-2.802.20-3.703.00-5.10

16.2021.2029.40

4.605.106.40

2.50-4.303.30-5.704.50-7.90

24.8032.4045.00

12.1013.6017.10

0.30-2.700.40-3.600.50-5.00

27.2035.4049.20

7.608.6010.80

3.004.005.50

30.2039.4054.70

8.509.5012.00

444

AB70 160 MB6AB70 160 L 6

AB75 160 MB 6AB75 160 L 6

AC70 160 MB6AC70 160 L 6

AC75 160 MB 6AC75 160 L 6

7.5011.00

16.0023.00

0.50-4.800.70-7.00

48.3070.80

10.2014.80

1.10-5.401.60-7.90

54.3079.60

11.5016.60

3.30-6.704.90-9.80

67.2098.50

14.2020.50

4.00-7.005.90-10.30

40.5059.40

8.5012.40

6.20-10.709.00-15.70

62.0091.00

22.7033.00

0.70-6.801.00-9.90

67.9099.50

14.3020.80

7.5011.00

75.40110.60

15.9023.10

44

AB70 180 L 6 AB75 180 L 6 AC70 180 L 6 AC75 180 L 6 15.00 29.00 1.00-9.60 96.00 18.30 2.20-10.80 107.00 20.60 6.70-13.40 133.00 25.50 8.10-14.00 80.00 15.40 12.30-21.50 123.00 40.90 1.40-13.50 134.00 25.70 15.00 149.00 28.60 4

AB70 200 LA 6AB70 200 LB 6

AB75 200 LA 6AB75 200 LB 6

AC70 200 LA 6AC70 200 LB 6

AC75 200 LA 6AC75 200 LB 6

18.5022.00

38.0044.00

1.20-11.801.40-14.10

116.00137.00

24.4028.30

2.70-13.303.20-15.80

130.00154.00

27.4031.90

8.20-16.509.80-19.60

161.00191.00

34.0039.40

9.90-17.3011.80-20.60

97.00115.00

20.5023.80

15.20-26.5018.10-31.50

149.00176.00

54.5063.30

1.70-16.702.00-18.80

163.00193.00

34.3039.80

18.5022.00

181.00214.00

38.1044.30

44

AB70 225 M 6 AB75 225 M 6 AC70 225 M 6 AC75 225 M 6 30.00 61.00 1.90-19.20 186.00 38.60 4.30-21.60 209.00 43.40 13.40-26.70 259.00 53.80 16.10-28.00 156.00 32.40 23.40-40.80 227.00 81.90 2.70-27.00 262.00 54.30 30.00 291.00 60.30 4

AB70 250 M 6 AB75 250 M 6 AC70 250 M 6 AC75 250 M 6 37.00 72.00 2.40-23.70 228.00 46.00 5.30-26.60 257.00 51.80 16.50-33.00 318.00 64.10 19.90-34.60 192.00 38.60 28.90-50.30 279.00 97.70 3.30-33.30 321.00 64.70 37.00 357.00 71.90 4

AB70 280 S 6AB70 280 M 6

AB75 280 6 6AB75 280 6 6

AC70 280 S 6AC70 280 M 6

AC75 280 S 6AC75 280 M 6

45.0055.00

90.50109.00

2.90-28.803.50-35.20

280.00343.00

58.4068.90

6.30-31.507.70-38.50

306.00375.00

63.8075.40

19.40-38.7023.70-47.30

376.00461.00

78.4092.60

20.30-35.2024.70-43.10

197.00241.00

41.0048.50

35.10-61.1043.00-74.70

342.00419.00

123.90146.20

4.00-39.604.80-48.40

385.00472.00

80.3094.80

45.0055.00

438.00536.00

91.20107.70

44





75.0090.00110.00132.00

147.20167.60205.00243.00

4.80-48.005.80-57.607.00-70.408.50-84.50

463.00558.00676.00811.00

93.30111.90130.20156.30

10.50-52.5012.60-63.0015.40-77.0018.50-92.40

506.00611.00740.00887.00

102.00122.40142.40170.90

32.20-64.5038.70-77.4047.30-94.6056.80-113.50

622.00750.00909.001090.00

125.30150.40175.00210.00

33.70-58.7040.50-70.5049.50-86.1059.40-103.30

326.00393,00476.00570.00

65.6078.7091.60109.90

58.60-101.9070.30-122.3085.90-149.40103.10-179.30

565.00681.00825.00989.00

197.90237.50276.30331.60

6.60-66.007.90-79.209.70-96.80

11.60-116.10

637.00768.00930.001115.00

128.30153.90179.00214.90

75.0090.00110.00132.00

724.00873.001057.001267.00

145.80174.90203.50244.20

4444

ENGLISH

4.4.5


II 2GII 2GD


6

Pole ENGLISH






241240

400 V, 50 Hz

[1/min] 750

[Hz] 5 ÷ 50range 1 ÷ 10

[1/min] 75 ÷ 750

[Hz] 10 ÷ 50range 1 ÷ 5

[1/min] 150 ÷ 750

[Hz] 25 ÷ 50range 1 ÷ 2

[1/min] 375 ÷ 750

[Hz] 50 ÷ 87range 10 ÷ 17

[1/min] 750 ÷ 1300

[Hz] 50 ÷ 87range 10 ÷ 17

[1/min] 750 ÷ 1300

[Hz] 5 ÷ 50range 1 ÷ 10

[1/min] 75 ÷ 750

[Hz] 5 ÷ 50range 1 ÷ 10

[1/min] 75 ÷ 750




























IIB IIC Pn[kW]

In[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A]

P[kW]

M[Nm]

I[A] B


AB70 63 B 8 AB75 63 B 8 AC70 63 B 8 AC75 63 B 8 0.05 0.44 0.003-0.03 0.52 0.29 0.01-0.04 0.58 0.32 0.02-0.04 0.72 0.40 0.03-0.05 0.43 0.24 0.04-0.07 0.67 0.64 --- --- --- 0.05 0.81 0.45 4

AB70 71 B 8 AB75 71 B 8 AC70 71 B 8 AC75 71 B 8 0.15 0.57 0.01-0.10 1.53 0.34 0.02-0.11 1.72 0.38 0.07-0.13 2.13 0.48 0.08-0.14 1.28 0.29 0.12-0.21 1.96 0.76 --- --- --- 0.15 2.39 0.53 4

AB70 80 A 8AB70 80 B 8

AB75 80 A 8AB75 80 B 8

AC70 80 A 8AC70 80 B 8

AC75 80 A 8AC75 80 B 8

0.180.25

0.971.00

0.01-0.120.02-0.16

1.562.21

0.580.63

0.03-0.130.04-0.18

1.762.49

0.650.71

0.08-0.160.11-0.22

2.173.08

0.810.88

0.10-0170.13-0.23

1.311.86

0.490.53

0.15-0.260.21-0.36

2.002.84

1.301.41

------

------

------

0.180.25

2.443.46

0.910.99

44

AB70 90 S 8AB70 90 L 8

AB75 90 S 8AB75 90 L 8

AC70 90 S 8AC70 90 L 8

AC75 90 S 8AC75 90 L 8

0.370.55

1.301.90

0.02-0.240.04-0.35

3.334.94

0.831.22

0.05-0.270.08.0.40

3.745.56

0.931.37

0.16-0.330.24-0.49

4.636.88

1.151.70

0.20-0.350.30-0.51

2.794.15

0.701.02

0.30-0.530.45-0.79

4.276.35

1.852.73

------

------

------

0.370.55

5.207.72

1.291.91

44

AB70 100 LA 8AB70 100 LB 8

AB75 100 LA 8AB75 100 LB 8

AC70 100 LA 8AC70 100 LB 8

AC75 100 LA 8AC75 100 LB 8

0.751.10

2.903.10

0.05-0.480.07-0.70

6.379.96

1.851.99

0.11-0.540.16-0.79

7.1611.21

2.082.24

0.33-0.670.49-0.98

8.8613.87

2.572.77

0.40-0.700.59-1.03

5.348.36

1.551.67

0.62-1.070.90-1.57

8.1812.79

4.124.45

0.07-0.670.10-0.99

8.9514.01

2.602.80

0.751.10

9.9515.56

2.893.11

44

AB70 112 M 8 AB75 112 M 8 AC70 112 M 8 AC75 112 M 8 1.50 4.40 0.10-1.00 12.70 2.80 0.20-1.10 14.30 3.20 0.70-1.30 17.70 3.90 0.80-1.40 10.70 2.40 1.20-2.10 16.40 6.30 0.10-1.40 17.90 3.90 1.50 19.90 4.40 4

AB70 132 SB 8AB70 132 ML 8

AB75 132 SB 8AB75 132 ML 8

AC70 132 SB 8AC70 132 ML 8

AC75 132 SB 8AC75 132 ML 8

2.203.00

6.508.50

0.10-1.400.20-1.90

18.7025.50

4.105.40

0.30-1.600.40-2.20

21.0028.70

4.606.00

1.00-2.001.30-2.70

26.0035.50

5.707.50

1.20-2.101.60-2.80

15.7021.40

3.404.50

1.80-3.202.50-4.30

24.0032.70

9.2012.00

0.20-2.000.30-2.70

26.3035.80

5.807.50

2.203.00

29.2039.80

6.408.40

44

AB70 160 MA8AB70 160 MB8AB70 160 L 8

AB75 160 MA 8AB75 160 MB 8AB75 160 L 8

AC70 160 MA8AC70 160 MB8AC70 160 L 8

AC75 160 MA 8AC75 160 MB 8AC75 160 L 8

4.005.507.50

9.7014.0018.00

0.30-2.600.40-3.500.50-4.80

34.1046.4063.70

6.208.7011.20

0.60-2.900.80-4.001.10-5.40

38.3052.2071.60

7.009.8012.70

1.80-3.602.50-4.903.30-6.70

47.4064.6088.60

8.6012.1015.70

2.20-3.703.00-5.104.00-7.00

28.6038.9053.40

5.207.309.40

3.30-5.704.50-7.906.20-10.70

43.7059.6081.80

13.9019.4025.10

0.40-3.600.50-5.000.70-6.80

47.9065.2089.50

8.7012.2015.80

4.005.507.50

53.2072.5099.50

9.7013.6017.60

444

AB70 180 L 8 AB75 180 L 8 AC70 180 L 8 AC75 180 L 8 11.00 23.00 0.70-7.00 93.00 14.80 1.60-7.90 105.00 16.60 4.90-9.80 130.00 20.60 5.90-10.30 78.00 12.40 9.00-15.70 120.00 33.00 1.00-9.90 131.00 20.80 11.00 146.00 23.10 4


AB70 225 S 8AB70 225 M 8

AB75 225 S 8AB75 225 M 8

AC70 225 S 8AC70 225 M 8

AC75 225 S 8AC75 225 M 8

18.5022.00

42.2546.00

1.20-11.801.40-14.10

155.00184.00

24.6029.20

2.70-13.303.20-15.80

174.00207.00

27.7032.90

8.20-16.509.80-19.60

216.00256.00

34.2040.70

9.90-17.3011.80-20.60

130.00155.00

20.6024.50

14.40-25.1017.20-29.90

189.00225.00

52.2062.00

1.70-16.702.00-19.80

218.00259.00

34.6041.10

18.5022.00

242.00288.00

38.4045.70

44

AB70 250 M 8 AB70 250 M 8 AC70 250 M 8 AC75 250 M 8 30.00 61.00 1.90-19.20 248.00 38.80 4.30-21.60 279.00 43.60 13.40-26.70 345.00 54.00 16.10-28.00 208.00 32.50 23.40-40.80 302.00 82.30 2.70-27.00 348.00 54.50 30.00 387.00 60.60 4

AB70 280 S 8AB70 280 M 8

AB75 280 S 8AB75 280 M 8

AC70 280 S 8AC70 280 M 8

AC75 280 S 8AC75 280 M 8

37.0045.00

71.0083.00

2.40-23.702.90-28.80

310.00372.00

44.2053.30

5.20-25.906.30-31.50

339.00407.00

48.3058.30

15.90-31.8019.40-38.70

416.00500.00

59.3071.60

16.70-29.0020.30-35.20

218.00262.00

31.0037.50

28.90-50.3035.10-61.10

378.00454.00

93.70113.00

3.30-32.604.00-39.60

426.00512.00

60.7073.20

37.0045.00

484.00582.00

69.0083.30

44





55.0075.0090.00110.00

113.50136.60164.50102.00

3.50-35.204.80-48.005.80-57.607.00-70.40

453.00624.00739.00905.00

71.9090.80104.20128.70

7.70-38.5010.50-52.5012.60-63.0015.40-77.00

496.00682.00809.00990.00

78.6099.40113.90140.70

23.70-47.3032.20-64.5038.70-77.4047.30-94.60

609.00838.00994.001216.00

96.60122.10140.00172.90

24.70-43.1033.70-58.7040.50-70.5049.50-86.10

319.00439.00520.00636.00

50.5063.9073.2090.50

42.90-74.7058.60-101.9070.30-122.3085.90-149.40

553.00761.00902.001104.00

152.50192.70221.00273.00

4.80-48.406.60-66.007.90-79.209.70-96.80

623.00858.001017.001244.00

98.80124.90143.20176.90

55.0075.0090.00110.00

708.00975.001155.001414.00

112.30142.00162.80201.10

4444

ENGLISH

4.4.5


II 2GII 2GD


8

Pole ENGLISH






242

ENGLISH

4.4.5.1

Motors energized by inverter - Load capacity curves Variable torque - Weakened flux

FRANÇAIS Moteurs alimentés par variateur - Courbes de chargeabilité Couple variable flux affaibli

DEUTSCH Motoren mit Umrichterversorgung - Belastungskurven Variables Drehmoment mit Feldschwächbetrieb

ESPAÑOL Motores alimentados con inverter - Curvas de capacidad de carga Par variable flujo debilitado

ITALIANO Motori alimentati da inverter - Curve di caricabilità Coppia variabile flusso indebolito

frame size - hauteur d’axe - Baugröße - tamaño - altezza d’asse63 ÷ 100

5 10 15 20 25 30 40 50 60 70 87 (Hz)

Mn (%)120

100

80

60

40

IC 411

IC 416


5 10 15 20 25 30 40 50 60 70 (Hz)

Mn (%)120

100

80

60

40

IC 411

IC 416


5 10 15 20 25 30 40 50 60 (Hz)

Mn (%)120

100

80

60

40

IC 411

IC 416


5 10 15 20 25 30 40 50 60 (Hz)

Mn (%)120

100

80

60

40

IC 411

IC 416



5 10 15 20 25 30 40 50 60 70 87 (Hz) 5 10 15 20 25 30 40 50 60 70 87 (Hz)

Mn (%)120

100

80

60

40

IC 411

IC 416

IC 411

IC 416

Mn (%)120

100

80

60

40

4 - 6 - 8 pole - pôles - polig - polos - poli

2 pole - pôles - polig - polos - poli

Mn (%) (Hz) IC 411 IC 416Torque Frequency Self-ventilated Forced ventilation (available from frame size 100)Couple Fréquence Autoventilés Ventilation assistée (disponible à partir de hauteur d’axe 100)Gegenmoment Frequenz Eigenbelüftet Fremdbelüftung (verfügbar ab Baugröße 100)Par Frequencia Autoventilados Ventilacion asistida (disponible a partir de altura del eje 100)Coppia Frequenza Autoventilati Ventilazione assistita (disponibile da altezza d'asse 100)

243

4.4.5.1

Motors energized by inverter - Load capacity curves Variable torque - constant flux ENGLISH

Moteurs alimentés par variateur - Courbes de chargeabilité Couple variable flux constant FRANÇAIS

Motoren mit Umrichterversorgung - Belastungskurven Variables Drehmoment mit konstantem Fluss DEUTSCH

Motores alimentados con inverter - Curvas de capacidad de carga Par variable flujo constante ESPAÑOL

Motori alimentati da inverter - Curve di caricabilità Coppia variabile flusso costante ITALIANO


5 10 15 20 25 30 40 50 60 70 87 (Hz)

Mn (%)120

100

80

60

40

IC 411

IC 416


5 10 15 20 25 30 40 50 60 70 (Hz)

Mn (%)120

100

80

60

40

IC 411

IC 416


5 10 15 20 25 30 40 50 60 (Hz)

Mn (%)120

100

80

60

40

IC 411

IC 416


5 10 15 20 25 30 40 50 60 (Hz)

Mn (%)120

100

80

60

40

IC 411

IC 416


5 10 15 20 25 30 40 50 60 (Hz)

Mn (%)120

100

80

60

40

IC 411

IC 416

2 pole - pôles - polig - polos - poli

Note:In the constant torque operating mode, the usable torque value is the lowest value of the chosen range of operationLors du fonctionnement à couple constant la valeur de couple utilisable est la valeur inférieure à la plage de fonctionnement sélectionnéeIm Betrieb mit konstantem Drehmoment ist der verwendbare Momentwert der Mindestwert des gewählten BetriebsbereichsEn el funcionamiento con par constante el valor de par que se puede utilizar es el valor menor del intervalo de funcionamiento elegidoNel funzionamento a coppia costante il valore di coppia utilizzabile è il valore minore del range di funzionamento prescelto

The reference torque value (Mn) is the value indicated in the tables in section 4.1La valeur de couple de référence (Mn) est celle indiquée dans les tableaux de la section 4.1Der Richtwert des Drehmoments (Mn) ist der in den Tabellen in Abschnitt 4.1 angegebeneEl valor de par de referencia (Mn) es el que recogen las tablas de la sección 4.1Il valore di coppia di riferimento (Mn) è quello indicato nelle tabelle della sezione 4.1

244


5 10 15 20 25 30 40 50 60 70 87 (Hz)

Mn (%)120

100

80

60

40

IC 411

IC 416


5 10 15 20 25 30 40 50 60 70 87 (Hz)

Mn (%)120

100

80

60

40


5 10 15 20 25 30 40 50 60 70 87 (Hz)

Mn (%)120

100

80

60

40

IC 411

IC 416

IC 411

IC 416


0 10 20 30 40 50 60 (Hz)

Mn (%)120

100

80

60

40

20

0

IC 411

4 - 6 - 8 pole - pôles - polig - polos - poli

2 - 4 - 6 - 8 pole - pôles - polig - polos - poli

ENGLISH

4.4.5.1

Motors energized by inverter - Load capacity curves Variable torque – constant flux

FRANÇAIS Moteurs alimentés par variateur - Courbes de chargeabilité Couple variable flux constant

DEUTSCH Motoren mit Umrichterversorgung - Belastungskurven Variables Drehmoment mit konstantem Fluss

ESPAÑOL Motores alimentados con inverter - Curvas de capacidad de carga Par variable flujo constante

ITALIANO Motori alimentati da inverter - Curve di caricabilità Coppia variabile flusso costante

4.4.5.2

Motors energized by inverter - Load capacity curves Quadratic torque

Moteurs alimentés par variateur - Courbes de chargeabilité Couple quadratique

Motoren mit Umrichterversorgung - Belastungskurven Quadratisches Gegenmoment

Motores alimentados con inverter - Curvas de capacidad de carga Par cuádratico

Motori alimentati da inverter - Curve di caricabilità Coppia quadratica

Note:see page 242, 243;voir page 242, 243;siehe Seite 242, 243;vèase página 242, 243;vedi pagina 242, 243;

245

5. Overall dimensions

5. Dimensions

5. Abmessungen

5. Dimensiones de espacio máximo

5. Dimensioni d'ingombro

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

ITALIANO

246

l AFAL

OA

G

øA

C

øKE C B

BCBB

EA

LLMLC

AO

AAA

AB

HA

HA

DH

D

IM B3

IM B5

AL

O

AG

øA

C

E EA

L

LM

LC

AO

AD

LAT

øM

øP

øN

S

AL

OA

G

øA

C

øKE C B

BCBB

EA

LLMLC

AO

AAA

AB

HA

HA

D

HD

IM B35

LAT

øMS

øP

øN

F

GA

DB

øD øDA

GC

DC

FA ¿

225÷3158 holes8 trous8 Bohrungen8 orificios8 fori

GD

GF

+

l AF+

l AF+

5. 63÷315 IM B3 IM B5 IM B35

ENGLISH Overall dimensions [mm]FRANÇAIS Dimensions [mm]DEUTSCH Abmessungen [mm]ESPAÑOL Dimensiones [mm]

ITALIANO Dimensioni d'ingombro [mm]

Type A AA AB ø AC AD l+ AF AL B BC BB C 0H- 0,5 HA HD ø K L LC

63 100 25 125 123 145 139 95 80 9.5 105 40 63 6 208 7 247 275.571 112 32 140 140 155 139 106 90 11.0 112 45 71 7 226 7 276 311.080 125 40 160 158 165 139 142 100 15.0 130 50 80 8 245 9 327 372.590 S90 L

140140

4545

175175

178178

175175

139139

125125

100125

14.014.0

157157

5656

9090

99

265265

99

390390

441.0441.0

100 160 45 200 196 185 139 125 140 15.0 170 63 100 10 285 12 430 490.5112 190 45 235 223 206 139 138 140 17.0 175 70 112 12 318 12 475 543.5132 S132 M-L

216216

5656

272272

258258

260260

205205

163163

140178

22.022.0

222222

8989

132132

1313

392392

1212

505580

590.0665.0

160 M160 L

254254

6464

318318

310310

290290

205205

166166

210254

25.025.0

305305

108108

160160

1515

450450

1414

693693

811.0811.0

180 M180 L

279279

7171

350350

359359

326326

223223

223223

241279

25.025.0

340340

121121

180180

1717

506506

1414

814814

923.5923.5

200 318 75 393 395 346 223 230 305 27.0 360 133 200 18 546 18 867 985.0225 S225 M 2225 M 4-8

356356356

787878

431431431

445445445

371371371

223223223

240240240

286311311

38.038.038.0

380380380

149149149

225225225

202020

596596596

181818

945915945

1090.01030.01090.0

250 M 2250 M 4-8

406406

9595

500500

467467

396396

223223

221221

349349

33.033.0

415415

168168

250250

2222

646646

2424

963963

1110.01110.0

280 S 2280 S 4-8280 M 2280 M 4-8

457457457457

90909090

540540540540

558558558558

548548548548

320320320320

316316316316

368368419419

80.080.080.080.0

550550550550

190190190190

280280280280

41414141

828828828828

25252525

1119111911191119

1272.01272.01272.01272.0

315 S 2315 S 4-8315 M 2315 M 4-8

508508508508

110110110110

590590590590

558558558558

536536536536

320320320320

316316316316

406406457457

32.032.032.032.0

470470521521

216216216216

315315315315

41414141

851851851851

27272727

1269129912691299

1420.01480.01420.01480.0

315 L 2 508 100 590 626 612 320 330 457 68.5 610 216 315 41 927 24 1407 1560.0315 L 4-8 508 100 590 626 612 320 330 508 68.5 610 216 315 41 927 24 1437 1620.0

Type

LMAO

IEC 423n. x O

AGø Dø DA

EEA

FFA

GAGC

GDGF

DBDC

LA ø M ø N ø P S T

63 275 24 1 x M25 100 11j6 23 4 12.5 4 M4 6.5 115 95j6 140 10 3.071 305 24 1 x M25 110 14j6 30 5 16.0 5 M5 6.5 130 110j6 160 10 3.580 356 24 1 x M25 120 19j6 40 6 21.5 6 M6 11.0 165 130j6 200 12 3.590 S90 L

418418

2424

1 x M251 x M25

130130

24j624j6

5050

88

27.027.0

77

M8M8

12.012.0

165165

130j6130j6

200200

1212

3.53.5

100 458 24 1 x M25 140 28j6 60 8 31.0 7 M10 14.0 215 180j6 250 15 4.0112 503 24 1 x M25 161 28j6 60 8 31.0 7 M10 16.0 215 180j6 250 15 4.0132 S132 M-L

550625

3535

2 x M322 x M32

185185

38k638k6

8080

1010

41.041.0

88

M12M12

17.017.0

265265

230j6230j6

300300

1515

4.04.0

160 M160 L

738738

3535

2 x M322 x M32

215215

42k642k6

110110

1212

45.045.0

88

M16M16

18.018.0

300300

250h6250h6

350350

1818

5.05.0

180 M180 L

860860

3838

2 x M402 x M40

266266

48k648k6

110110

1414

52.052.0

99

M16M16

20.020.0

300300

250h6250h6

350350

1818

5.05.0

200 913 38 2 x M40 286 55m6 110 16 59.0 10 M20 20.0 350 300h6 400 18 5.0225 S225 M 2225 M 4-8

991961991

383838

2 x M402 x M402 x M40

311311311

60m655m660m6

140110140

181618

64.059.064.0

111011

M20M20M20

22.022.022.0

400400400

350h6350h6350h6

450450450

181818

5.05.05.0

250 M 2250 M 4-8

10061006

3838

2 x M402 x M40

336336

60m665m6

140140

1818

64.069.0

1111

M20M20

22.022.0

500500

450h6450h6

550550

1818

5.05.0

280 S 2280 S 4-8280 M 2280 M 4-8

1215121512151215

56565656

2 x M632 x M632 x M632 x M63

410410410410

65m675m665m675m6

140140140140

18201820

69.079.569.079.5

11121112

M20M20M20M20

18.018.018.018.0

500500500500

450h6450h6450h6450h6

550550550550

18181818

5.05.05.05.0

315 S 2315 S 4-8315 M 2315 M 4-8

1365139513651395

56565656

2 x M632 x M632 x M632 x M63

398398398398

65m680m665m680m6

140170140170

18221822

69.085.069.085.0

11141114

M20M20M20M20

22.022.022.022.0

600600600600

550h6550h6550h6550h6

660660660660

22222222

6.06.06.06.0

315 L 2 1503 56 2 x M63 474 65m6 140 18 69.0 11 M20 22.0 600 550h6 660 24 6.0315 L 4-8 1533 56 2 x M63 474 80m6 170 22 85.0 14 M20 22.0 600 550h6 660 24 6.0

247

see page 246; voir page 246; siehe Seite 246; véase página 246; vedi pagina 246;

see page 249; voir page 249; siehe Seite 249; véase página 249; vedi pagina 249;

Overall dimensions [mm] ENGLISH

Dimensions [mm] FRANÇAIS

Abmessungen [mm] DEUTSCH

Dimensiones [mm] ESPAÑOL

Dimensioni d'ingombro [mm] ITALIANO

248

AL

OA

G

øA

C

EEA

LLMLC

AO

AD

IM B14

IM B34

AAA

AB

HA

HA

D

HD

øM

S

AL

O

AG

øA

C

øKE C B

BCBB

EA

L

LM

LC

AO

T

øP

øN

T

øM

F

GA

DB

øD øDA

GC

DC

FA

GD

GF

l AF+

l AF+

øP

øN

S

5. 63÷160 IM B14 IM B34

ENGLISH Overall dimensions [mm]FRANÇAIS Dimensions [mm]DEUTSCH Abmessungen [mm]ESPAÑOL Dimensiones [mm]

ITALIANO Dimensioni d'ingombro [mm]

Type A AA AB ø AC AD l+ AF AL B BC BB C 0H- 0,5 HA HD ø K L LC

63 100 25 125 123 145 139 95 80 9.5 105 40 63 6 208 7 247 275.5

71 112 32 140 140 155 139 106 90 11.0 112 45 71 7 226 7 276 311.0

80 125 40 160 158 165 139 142 100 15.0 130 50 80 8 245 9 327 372.5

90 S90 L

140140

4545

175175

178178

175175

139139

125125

100125

14.014.0

157157

5656

9090

99

265265

99

390390

441.0441.0

100 160 45 200 196 185 139 125 140 15.0 170 63 100 10 285 12 430 490.5

112 190 45 235 223 206 139 138 140 17.0 175 70 112 12 318 12 475 543.5

132 S132 M-L

216216

5656

272272

258258

260260

205205

163163

140178

22.022.0

222222

8989

132132

1313

392392

1212

505580

590.0665.0

160 M160 L

254254

6464

318318

310310

290290

205205

166166

210254

25.025.0

305305

108108

160160

1515

450450

1414

693693

811.0811.0

rain canopy: only when vertical shaft-down mounting 1 in the terminal box, 1 on the frameparapluie: uniquement pour position verticale, arbre vers le bas 1 à l'intérieur de la boîte à bornes, 1 sur la carcasseRegenschutzdach: nur für die Vertikalbauformen 1 am Klemmkasten, 1 am Motorgehäusetapa de protección contra la lluvia: sólo para montaje en vertical, eje en la parte inferior 1 en la caja de bornes, 1 en la carcasaparapioggia: normalmente presente solo per montaggio verticale, albero in basso 1 nella scatola morsetti, 1 sulla carcassa

Tolerances allowedDimensions données à titre indicatifÜbliche ToleranzenCotas no vinculantesQuote non impegnative

280 and 315 L fixed feet. Removable feet available on request with different dimensions.280 et 315 L pieds fixes standards, sur demande pieds amovibles avec des mesures autres que celles indiquées280 und 315 L ortsfeste Standardfüße, auf Wunsch entfernbare Füße mit von den angegebenen abweichenden Abmessungen280 y 315 L pies fijos estándar, bajo pedido pies desmontables de medidas diferentes de las indicadas280 e 315 L piedi fissi standard, su richiesta piedi removibili con misure d’ingombro diverse da quelle indicate

249

Overall dimensions [mm] ENGLISH

Dimensions [mm] FRANÇAIS

Abmessungen [mm] DEUTSCH

Dimensiones [mm] ESPAÑOL

Dimensioni d'ingombro [mm] ITALIANO

Type

LMAO

IEC 423n. x O

AGø Dø DA

EEA

FFA

GAGC

GDGF

DBDC

ø M ø N ø P S T

63 275 24 1 x M25 100 11j6 23 4 12.5 4 M4 75 60j6 90 M5 2.5

71 305 24 1 x M25 110 14j6 30 5 16.0 5 M5 85 70j6 105 M6 2.5

80 356 24 1 x M25 120 19j6 40 6 21.5 6 M6 100 80j6 120 M6 3.0

90 S90 L

418418

2424

1 x M251 x M25

130130

24j624j6

5050

88

27.027.0

77

M8M8

115115

95j695j6

140140

M8M8

3.03.0

100 458 24 1 x M25 140 28j6 60 8 31.0 7 M10 130 110j6 160 M8 3.5

112 503 24 1 x M25 161 28j6 60 8 31.0 7 M10 130 110j6 160 M8 3.5

132 S132 M-L

550625

3535

2 x M322 x M32

185185

38k638k6

8080

1010

41.041.0

88

M12M12

165165

130j6130j6

200200

M10M10

3.53.5

160 M160 L

738738

3535

2 x M322 x M32

215215

42k642k6

110110

1212

45.045.0

88

M16M16

215215

180h6180h6

250250

M12M12

4.04.0

251

6. Spare parts

6. Pièces détachées

6. Ersatzteilliste

6. Piezas de repuesto

6. Parti di ricambio

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

ITALIANO

252

3 4 6 7 8 9 10 11 12 16

17 18 20 25 26 27 (28)

1 (2) 3 4 6 8 7 9 10 11 12 16 12 (14) (15) 16

17 18 20 22 25 26 27 (28) (24) 25 26 27 (28)

6.

ENGLISH Spare partsFRANÇAIS Pièces detachéesDEUTSCH ErsatzteillisteESPAÑOL Piezas de repuesto

ITALIANO Parti di ricambio

63 ÷ 132

160

253

Spare parts ENGLISH

Pièces detachées FRANÇAIS

Ersatzteilliste DEUTSCH

Piezas de repuesto ESPAÑOL

Parti di ricambio ITALIANO

ENGLISH

1 End cap - front(2) Grease nipple - front3 Front bearing4 Terminal box6 Terminal box lid7 Terminal board8 Cable nipple9 Rotor

101112(14)(15)161718

StatorFrameEndshield - rearGrease nipple - rearEnd cap - rearFan cover (cowl)ShaftSealing ring - front

202225(24)2627(28)

Endshield - frontInner bearing cap - frontRear bearingInner bearing cap - rearSealing ring - rearCooling fanRain cap(...) = when provided

FRANÇAIS

1 Couvercle avant(2) Graisseur avant

3 Roulement avant4 Boîte à bornes6 Couvercle boîte à bornes7 Bornes8 Dispositif pour le passage des câbles9 Rotor

101112

(14)(15)

161718

StatorCarcasseFlasque arrièreGraisseur arrièreCouvercle arrièreCapot de ventilateurArbreBague avant d’étanchéité

202225

(24)2627

(28)

Flasque avantFlasque intérieur avantRoulement arrièreFlasque intérieur arrièreBague arrière d’étanchéitéVentilateurTôle parapluie(...) = si prévu

DEUTSCH

1 Äußerer Fettkammerdeckel A-Seite(2) Schmiernippel A-Seite3 Kugellager A-Seite4 Klemmkasten6 Klemmkastendeckel7 Klemmbrett8 Druckfeste Kabeldurchführung9 Läufer

101112(14)(15)161718

StatorpaketMotorgehäuseLagerschild B-SeiteSchmiernippel B-SeiteÄußerer Fettkammerdeckel B-SeiteLüfterhaubeWelleDichtungsring A-Seite

202225(24)2627(28)

Lagerschild A-SeiteInnerer Fettkammerdeckel A-SeiteKugellager B-SeiteInnerer Fettkammerdeckel B-SeiteDichtungsring B-SeiteLüfterflügelRegenschutzdach(...) = wenn vorgesehen

ESPAÑOL

1 Tapa externa delantera(2) Engrasador delantero

3 Cojinete delantero4 Caja de bornes6 Tapa de la caja de bornes7 Placa de bornes8 Niple paso cables9 Rotor

101112

(14)(15)

161718

EstatorArmazónEscudo traseroEngrasador traseroFondo externo traseroCasquete cubre ventiladorEjeAnillo de retención delantero

202225

(24)2627

(28)

Escudo delanteroFondo interno delanteroCojinete traseroTapa interna traseraAnillo de retención traseroVentiladorTapa de protección contra la lluvia(...) = cuando previsto

ITALIANO

1 Fondello esterno anteriore(2) Ingrassatore anteriore3 Cuscinetto anteriore4 Scatola morsetti6 Coperchio scatola morsetti7 Morsettiera8 Nipplo passaggio cavi9 Rotore

101112(14)(15)161718

StatoreCarcassaScudo posterioreIngrassatore posterioreFondello esterno posterioreCalotta copriventolaAlberoAnello di tenuta anteriore

202225(24)2627(28)

Scudo anterioreFondello interno anterioreCuscinetto posterioreFondello interno posterioreAnello di tenuta posterioreVentolaTettuccio parapioggia(...) = quando previsto

254

6.

ENGLISH Spare partsFRANÇAIS Pièces detachéesDEUTSCH ErsatzteillisteESPAÑOL Piezas de repuesto

ITALIANO Parti di ricambio

1 (2) 3 4 6 7 (5) 9 10 11 12 13 (14) (15) 16

17 18 19 20 21 22 (23) (24) 25 26 27 (28)

1 (2) 3 4 (5) 6 7 9 10 11 12 16 12 (14) (15) 16

17 18 20 22 25 26 27 (28) (24) 25 26 27 (28)

180 ÷ 250

280 ÷ 315

255

Spare parts ENGLISH

Pièces detachées FRANÇAIS

Ersatzteilliste DEUTSCH

Piezas de repuesto ESPAÑOL

Parti di ricambio ITALIANO

ENGLISH

1 End cap - front(2) Grease nipple - front3 Front bearing4 Terminal box(5) Auxiliary connections6 Terminal box lid7 Terminal board9 Rotor10 Stator

111213(14)(15)16171819

FrameEndshield - rearGrease sealing ring - rearGrease nipple - rearEnd cap - rearFan cover (cowl)ShaftSealing ring - frontGrease sealing ring - front

202122(23)(24)252627(28)

Endshield - frontPre loading springsInner bearing cap - frontFeetInner bearing cap - rearRear bearingSealing ring - rearCooling fanRain cap(...) = when provided

FRANÇAIS

1 Couvercle avant(2) Graisseur avant

3 Roulement avant4 Boîte à bornes

(5) Dispositif pour le passage desauxiliaires

6 Couvercle boîte à bornes7 Bornes traversante9 Rotor

10 Stator

111213

(14)(15)

16171819

CarcasseFlasque arrièreBague arrière de rétention graisseGraisseur arrièreCouvercle arrièreCapot de ventilateurArbreBague avant d’étanchéitéBague avant de rétention graisse

202122

(23)(24)

252627

(28)

Flasque avantRessorts de préchargeFlasque intérieur avantPattesFlasque intérieur arrièreRoulement arrièreBague arrière d’étanchéitéVentilateurTôle parapluie(...) = si prévu

DEUTSCH

1 Äußerer Fettkammerdeckel A-Seite(2) Schmiernippel A-Seite3 Kugellager A-Seite4 Klemmkasten(5) Kabeldurchfürung Hilfskreise6 Klemmkastendeckel7 Klemmbrett9 Läufer10 Statorpaket

111213(14)(15)16171819

MotorgehäuseLagerschild B-SeiteSchmierfett – Schleuderring B-SeiteSchmiernippel B-SeiteÄußerer Fettkammerdeckel B-SeiteLüfterhaubeWelleDichtungsring A-SeiteSchmierfett Schleuderring A-Seite

202122(23)(24)252627(28)

Lagerschild A-SeiteLagervorspannungInnerer Fettkammerdeckel A-SeiteFüßeInnerer Fettkammerdeckel B-SeiteKugellager B-SeiteDichtungsring B-SeiteLüfterflügelRegenschutzdach(...) = wenn vorgesehen

ESPAÑOL

1 Tapa externa delantera(2) Engrasador delantero

3 Cojinete delantero4 Caja de bornes

(5) Niple paso auxiliares6 Tapa de la caja de bornes7 Placa de bornes9 Rotor

10 Estator

111213

(14)(15)

16171819

ArmazónEscudo traseroAnillo retención grasa traseroEngrasador traseroFondo externo traseroCasquete cubre ventiladorEjeAnillo de retención delanteroAnillo retención grasa delantero

202122

(23)(24)

252627

(28)

Escudo delanteroMuelles de carga previaFondo interno delanteroPiesTapa interna traseraCojinete traseroAnillo de retención traseroVentiladorTapa de protección contra la lluvia(...) = cuando previsto

ITALIANO

1 Fondello esterno anteriore(2) Ingrassatore anteriore3 Cuscinetto anteriore4 Scatola morsetti(5) Nipplo passaggio ausiliari6 Coperchio scatola morsetti7 Morsettiera9 Rotore10 Statore

111213(14)(15)16171819

CarcassaScudo posterioreAnello ritenzione grasso posterioreIngrassatore posterioreFondello esterno posterioreCalotta copriventolaAlberoAnello di tenuta anterioreAnello ritenzione grasso anteriore

202122(23)(24)252627(28)

Scudo anterioreMolle di precaricoFondello interno anteriorePiediFondello interno posterioreCuscinetto posterioreAnello di tenuta posterioreVentolaTettuccio parapioggia(...) = quando previsto

Sales programme Programme Verkaufsprogramm Programa de venta Programma di vendita

Flameproof-Explosion proofmotorsEx d, Ex de• frame size 56 ÷ 315•power 0.06 ÷ 200 kW• threephase,1 or 2 speed,singlephase

• ventilated, unventilated•group I, IIA, IIB, IIC• category M2, 2G, 2D, 2GD• temperature classT3, T4, T5, T6

•maximum surfacetemperature [°C] T150, 135,125, 100, 85, 70

•with brake

MoteursantidéflagrantsEx d, Ex de•hauteur d’axe 56 ÷ 315•puissance 0.06 ÷ 200 kW• triphasés,à 1 ou 2 vitesses,monophasés

• ventilés, non ventilés• groupe I, IIA, IIB, IIC• catégorie M2, 2G, 2D, 2GD• classes de températureT3, T4, T5, T6

• température superficiellemaximum [°C] T150, 135,125, 100, 85, 70

• avec frein

ExplosionsgeschützteMotorenEx d, Ex de•Baugrößen 56 ÷ 315• Leistung 0.06 ÷ 200 kW•Drehstrommotoren,1 oder 2 Geschwindigkeiten,Einphasenmotoren

•mit Lüftung, ohne Lüftung•Gruppe I, IIA, IIB, IIC•Kategorie M2, 2G, 2D, 2GD• TemperaturklassenT3, T4, T5, T6

• maximale Oberflächen-temperatur [°C] T150, 135,125, 100, 85, 70

•mit Bremse

MotoresantideflagrantesEx d, Ex de• tamaños 56 ÷ 315•potencia 0.06 ÷ 200 kW• trifásicos,1 o 2 velocidades,monofásicos

• autoventilados o no•grupo I, IIA, IIB, IIC• categoría M2, 2G, 2D, 2GD• clase temperaturaT3, T4, T5, T6

•màxima temperaturasuperficial [°C] T150, 135,125, 100, 85, 70

• con freno

MotoriantideflagrantiEx d, Ex de•altezza d'asse 56 ÷ 315•potenze 0.06 ÷ 200 kW• trifase,1 o 2 velocità,monofase

• ventilato, non ventilato• gruppo I, IIA, IIB, IIC• categoria M2, 2G, 2D, 2GD• classi di temperaturaT3, T4, T5, T6

•massima temperaturasuperficiale [°C] T150, 135,125, 100, 85, 70

• con freno

Increased safetymotorsEx e• frame size 63 ÷ 132•power 0.12 ÷ 7.5 kW• threephase• group II• category 2G• temperature class T3

Moteurs à sécuritéaugmentéeEx e•hauteur d’axe 63 ÷ 132•puissance 0.12 ÷ 7.5 kW• triphasés• groupe II• catégorie 2G• classes de température T3

Motoren für erhöhteSicherheitEx e•Baugrößen 63 ÷ 132• Leistung 0.12 ÷ 7.5 kW•Drehstrommotoren•Gruppe II• Kategorie 2G• Temperaturklassen T3

Motores de seguridadaumentadaEx e• tamaños 63 ÷ 132•potencia 0.12 ÷ 7.5 kW• trifásicos• grupo II• categoría 2G• clase temperatura T3

Motori a sicurezzaaumentataEx e•altezza d'asse 63 ÷ 132•potenze 0.12 ÷ 7.5 kW• trifase• gruppo II• categoria 2G• classe di temperatura T3

Non sparking motorsEx nA• frame size 63 ÷ 315•power 0.12 ÷ 132 kW• threephase,1 or 2 speed

•group II• category 3G, 3GD• temperature class T3

Moteurs anti-étincellesEx nA•hauteur d’axe 63 ÷ 315•puissance 0.12 ÷ 132 kW• triphasés,à 1 ou 2 vitesses

• groupe II• catégorie 3G, 3GD• classes de température T3

Funkenfreie MotorenEx nA•Baugrößen 63 ÷ 315• Leistung 0.12 ÷ 132 kW•Drehstrommotoren,1 oder 2 Geschwindigkeiten

•Gruppe II• Kategorie 3G, 3GD• Temperaturklassen T3

Motores no sparkingEx nA• tamaños 63 ÷ 315•potencia 0.12 ÷ 132 kW• trifásicos,1 o 2 velocidades

• grupo II• categoría 3G, 3GD• clase temperatura T3

Motori non sparkingEx nA•altezza d'asse 63 ÷ 315•potenze 0.12 ÷ 132 kW• trifase,1 o 2 velocità

• gruppo II• categoria 3G, 3GD• classe di temperatura T3

Totally enclosed fan cooledIEC motors• frame size 63 ÷ 315•power 0.12 ÷ 132 kW• threephase,1 or 2 speed

• category 3D•protection IP55

Moteurs fermés IP55 CEI/IECavec ventilation extérieure•hauteur d’axe 63 ÷ 315•puissance 0.12 ÷ 132 kW• triphasés,à 1 ou 2 vitesses

• catégorie 3D•protection IP55

Geschlossene Motoren mitFremdbelüftung nach IEC•Baugrößen 63 ÷ 315• Leistung 0.12 ÷ 132 kW•Drehstrommotoren,1 oder 2 Geschwindigkeiten

•Kategorie 3D• Schutzart IP55

Motores cerradoscon ventilación exterior IP55• tamaños 63 ÷ 315•potencia 0.12 ÷ 132 kW• trifásicos,1 o 2 velocidades

• categoría 3D•protección IP55

Motori chiusi con ventilazioneesterna CEI/IEC•altezza d'asse 63 ÷ 315•potenze 0.12 ÷ 132 kW• trifase,1 o 2 velocità

• categoria 3D•protezione IP55

Centrifugal flameproofelectric pumpsfor printing machinesEx d - Ex de•group IIB, IIC• output over 300 l/min•head up to 15 m• stem length170 ÷ 550 mm

• special applications• detachable motor from thepump unit

Electropompes centrifugesantidéflagrantespour machines d'imprimerieEx d - Ex de•groupe IIB, IIC• debit supérieur à 300 l/min• hauteur de refoulement jusqu’à 15 m• corps immerge170 ÷ 550 mm

•applications spéciales•moteur détacable de l’unitèpompe

ExplosionsgeschützteZentrifugal-Elektropumpenfür DruckmaschinenEx d - Ex de•Gruppe IIB, IIC• Leistung bis 300 l/min•Bis zu 15 m Förderhöhe• Eintauchtiefe170 ÷ 550 mm

•Sonderanwendungen•Motor vom Pumpenkörperabnehmbar

Electrobombas centrífugasantideflagrantes paramáquinas de impresiónEx d - Ex de•grupo IIB, IIC• capacidad: más 300 l/min• altura: hasta 15 m•cuerpos sumergidos170 ÷ 550 mm

•aplicaciones especiales•motor separable del cuerpobomba

Elettropompe centrifugheantideflagrantiper macchine da stampaEx d - Ex de•gruppo IIB, IIC• portate oltre 300 l/min•prevalenze: fino a 15 m•corpi immersi170 ÷ 550 mm

•applicazioni speciali•motore separabile dal corpopompa

Centrifugal electric pumpsfor machine tools• submersible• output over 300 l/min•head up to 30 m• stem length90 ÷ 550 mm

• special applications

Electropompes centrifugespour machines-outils• immergeables• debit supérieur à 300 l/min• hauteur de refoulement jusqu'à 30 m• corps immerge90 ÷ 550 mm

•applications spéciales

Elektropumpen fürWerkzeugmaschinen•Eintauchfähig• Leistung mehr als 300 l/min•Bis zu 30 m Förderhöhe• Eintauchtiefe90 ÷ 550 mm

•Sonderanwendungen

Electrobombas centrífugaspara máquinas herramientas• sumergibles• capacidad: más 300 l/min• altura: hasta 30 m•cuerpos sumergidos90 ÷ 550 mm

•aplicaciones especiales

Elettropompe centrifugheper macchine utensili•ad immersione•portate oltre 300 l/min•prevalenze fino a 30 m•corpi immersi90 ÷ 550 mm

•applicazioni speciali

Every care has been taken to ensure the accu-racy of the information contained in thispublication.Due to Cemp’s policy of continuous develop-ment and improvement, the companyreserves the right to supply products whichmay differ slightly from those illustrated anddescribed in this publication.Descriptions and technical features listed inthis brochure may not be considered as bind-ing. Under no circumstances should data inthis publication be considered as a contrac-tual obligation.

Dans la préparation de cette documentationnous avons pris le soin d’y intégrer les infor-mations les plus exactes possibles.Néanmoins, compte tenu de notre politiquede développement et d’amélioration continuedes produits, la Société Cemp se réserve ledroit et la faculté d’apporter toute modifica-tion sur la documentation et sur les produits,à tout moment et sans préavis.Les descriptifs et les caractéristiques tech-niques contenus dans ce cataloguen’engagent pas la Société. Par conséquent,ces données ne constituent en aucun cas unengagement contractuel.

Die Ausführungen und technischenEigenschaften, die in dieser Broschüre ange-geben sind, dürfen nicht als verbindlichangesehen werden.In keinem Fall können jedoch die in diesemDokument aufgeführten technischen Datenals rechtlich verbindlich angesehen werden.Cemp behält sich das Recht vor, ohneMitteilung, jegliche Abweichungen und Ände-rungen jederzeit vorzunehmen, sowohl indiesem Dokument als auch bei denProdukten, die hier beschrieben sind.

La presente documentación se ha redactadode manera muy atenta para poder asegurarque las informaciones que contiene soncorrectas.No obstante, como consecuencia de la políti-ca de continuo desarrollo y mejora de la cali-dad del producto que Cemp pone en práctica,la sociedad se reserva el derecho y la facultadde modificar en lo que fuera necesario, encualquier momento y sin que para ello mediepreaviso alguno, tanto este documento comosus productos.Por lo tanto, las descripciones y las caracte-rísticas técnicas indicadas en el presentedocumento no son vinculantes, y los datosque contiene no constituyen en ningún caso,vínculo contractual.

Nel redigere questa documentazione è stataposta ogni cura al fine di assicurare la corret-tezza delle informazioni contenute.Tuttavia, anche in conseguenza della politicadi continuo sviluppo e miglioramento dellaqualità del prodotto perseguita da Cemp, lasocietà si riserva il diritto e la facoltà diapportare modifiche di qualsiasi genere, inqualsiasi momento e senza preavviso, sia aquesto documento sia ai propri prodotti.Le descrizioni e le caratteristiche tecnichedella presente pubblicazione non sono quindiimpegnative e i dati riportati non costituisco-no, in nessun caso, impegno contrattuale.

Cemp srlVia Piemonte, 1620030 SENAGO (Milan)ItalyTel. +39 02 94435401Fax +39 02 [email protected]

Cemp France SA

6 et 8, avenue Victor Hugo27320 NONANCOURTFranceTél. +33 (0)2 32580381Fax +33 (0)2 [email protected]

Cemp International GmbHAm Mollnhof 294036 PASSAUGermanyTel. +49 (0)851 9662320Fax +49 (0)851 [email protected]

Overall sales network at www.cemp.eu

flameproof motors moteurs antidéflagrants ... · pdf fileflameproof motors moteurs...

Documents