flow control cartridges - ertansoydan.com
TRANSCRIPT
Flow Control Cartridges
Powered by Sun QuickPrint,your on-demand, customized catalogue solution.
This information is subject to change without notice. Visit www.sunhydraulics.com for complete and up to date information.
© 2016 Sun Hydraulics
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Table of Contents
FQBA Fixed orifice, flow fusevalve
1
FQCA Fixed orifice, flow fusevalve
2
FQEA Fixed orifice, flow fusevalve
3
FQGA Fixed orifice, flow fusevalve
4
FQIA Fixed orifice, flow fusevalve
5
NFBC Fully adjustable needlevalve
6
NFCC Fully adjustable needlevalve
7
NFCD Fully adjustable needlevalve
8
NFDC Fully adjustable needlevalve
9
NFDD Fully adjustable needlevalve
10
NFEC Fully adjustable needlevalve
11
NFED Fully adjustable needlevalve
12
NFFC Fully adjustable needlevalve
13
NFFD Fully adjustable needlevalve
14
NCBB Fully adjustable needle valve with reverse flowcheck
15
NCCB Fully adjustable needle valve with reverse flowcheck
16
NCCC Fully adjustable needle valve with reverse flowcheck
17
NCCD Fully adjustable needle valve with reverse flowcheck
18
NCEB Fully adjustable needle valve with reverse flowcheck
19
NCEC Fully adjustable needle valve with reverse flowcheck
20
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Table of Contents
NCFB Fully adjustable needle valve with reverse flowcheck
21
NCFC Fully adjustable needle valve with reverse flowcheck
22
NCGB Fully adjustable needle valve with reverse flowcheck
23
NCGC Fully adjustable needle valve with reverse flowcheck
24
NFAB Fully adjustable needle valve - pilotcapacity
25
CNAC Fixed orifice, non-pressure compensated, flow control valve with reverse flowcheck
26
CNCC Fixed orifice, non-pressure compensated, flow control valve with reverse flowcheck
27
CNEC Fixed orifice, non-pressure compensated, flow control valve with reverse flowcheck
28
CNGC Fixed orifice, non-pressure compensated, flow control valve with reverse flowcheck
29
CNIC Fixed orifice, non-pressure compensated, flow control valve with reverse flowcheck
30
FXAA Fixed orifice, pressure compensated flow controlvalve
31
FXAG Flush mount, pressure compensated flowcontrol
32
FXAM Insert style, pressure compensated flowcontrol
33
FXBA Fixed orifice, pressure compensated flow controlvalve
34
FXCA Fixed orifice, pressure compensated flow controlvalve
35
FXDA Fixed orifice, pressure compensated flow controlvalve
36
FXEA Fixed orifice, pressure compensated flow controlvalve
37
FXFA Fixed orifice, pressure compensated flow controlvalve
38
FCBB Fixed orifice pressure compensated flow control valve with reverse flowcheck
39
FCCB Fixed orifice pressure compensated flow control valve with reverse flowcheck
40
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Table of Contents
FCDB Fixed orifice pressure compensated flow control valve with reverse flowcheck
41
FCEB Fixed orifice pressure compensated flow control valve with reverse flowcheck
42
FCFB Fixed orifice pressure compensated flow control valve with reverse flowcheck
43
FDBA Fully adjustable pressure compensated flow control valve with reverse flowcheck
44
FDCB Fully adjustable pressure compensated flow control valve with reverse flowcheck
45
FDEA Fully adjustable pressure compensated flow control valve with reverse flowcheck
46
FDFA Fully adjustable pressure compensated flow control valve with reverse flowcheck
47
FXDA8 Ventable fixed orifice, pressure compensated flow control valve with integral T-8Acontrol cavity
48
FRBA Fixed orifice, bypass/restrictive, priority, flow controlvalve
49
FRCA Fixed orifice, bypass/restrictive, priority, flow controlvalve
50
FRDA Fixed orifice, bypass/restrictive, priority, flow controlvalve
51
FREA Fixed orifice, bypass/restrictive, priority, flow controlvalve
52
FRFA Fixed orifice, bypass/restrictive, priority, flow controlvalve
53
FVCA Ventable, fixed orifice, bypass/restrictive, priority, flow controlvalve
54
FVDA Ventable, fixed orifice, bypass/restrictive, priority, flow controlvalve
55
FVEA Ventable, fixed orifice, bypass/restrictive, priority, flow controlvalve
56
FVFA Ventable, fixed orifice, bypass/restrictive, priority, flow controlvalve
57
FVCA8 Ventable, fixed orifice, bypass/restrictive, priority, flow control valve with integral T-8Acontrol cavity
58
FVDA8 Ventable, fixed orifice, bypass/restrictive, priority, flow control valve with integral T-8Acontrol cavity
59
FVEA8 Ventable, fixed orifice, bypass/restrictive, priority, flow control valve with integral T-8Acontrol cavity
60
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Table of Contents
FVFA8 Ventable, fixed orifice, bypass/restrictive, priority, flow control valve with integral T-8Acontrol cavity
61
FPCC Electro-proportional flow control valve - normallyclosed
62
FPCH Electro-proportional flow control valve - normallyopen
63
FPFK Pilot operated, normally closed, electro-proportional throttle with reverse flowcheck
64
FPHK Pilot operated, normally closed, electro-proportional throttle with reverse flowcheck
65
FMDA Electro-proportional 3-way flow control valve, meterin
66
FMDB Electro-proportional 3-way flow control valve, meterin
67
FTCA 2-way, pilot shifted, dual path, proportionalthrottle
68
FTDA 2-way, pilot shifted, dual path, proportionalthrottle
69
FTEA 2-way, pilot shifted, dual path, proportionalthrottle
70
FTFA 2-way, pilot shifted, dual path, proportionalthrottle
71
FTCAZ 2-way, pilot shifted, dual path, proportional throttle with positionswitch
72
FTDAZ 2-way, pilot shifted, dual path, proportional throttle with positionswitch
73
FTEAZ 2-way, pilot shifted, dual path, proportional throttle with positionswitch
74
FTFAZ 2-way, pilot shifted, dual path, proportional throttle with positionswitch
75
FKBA 2-way, pilot shifted, proportionalthrottle
76
FKCA 2-way, pilot shifted, proportional throttle, highcapacity
77
FKDA 2-way, pilot shifted, proportionalthrottle
78
FKEA 2-way, pilot shifted, proportional throttle, highcapacity
79
FKFA 2-way, pilot shifted, proportionalthrottle
80
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Table of Contents
FKGA 2-way, pilot shifted, proportional throttle, highcapacity
81
FKHA 2-way, pilot shifted, proportionalthrottle
82
FKIA 2-way, pilot shifted, proportional throttle, highcapacity
83
FKBB 2-way, pilot shifted, proportional throttle with bleeddown
84
FKCB 2-way, pilot shifted, proportional throttle with bleed down, highcapacity
85
FKDB 2-way, pilot shifted, proportional throttle with bleeddown
86
FKEB 2-way, pilot shifted, proportional throttle with bleed down, highcapacity
87
FKFB 2-way, pilot shifted, proportional throttle with bleeddown
88
FKGB 2-way, pilot shifted, proportional throttle with bleed down, highcapacity
89
FKHB 2-way, pilot shifted, proportional throttle with bleeddown
90
FKIB 2-way, pilot shifted, proportional throttle with bleed down, highcapacity
91
FSCD Flow dividervalve
92
FSDD Flow dividervalve
93
FSED Flow dividervalve
94
FSFD Flow dividervalve
95
FSBD High accuracy flow dividervalve
96
FSDC High accuracy flow dividervalve
97
FSEC High accuracy flow dividervalve
98
FSFC High accuracy flow dividervalve
99
FSCA Closed center, flow divider-combinervalve
100
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Table of Contents
FSDA Closed center, flow divider-combinervalve
101
FSEA Closed center, flow divider-combinervalve
102
FSFA Closed center, flow divider-combinervalve
103
FSAA High accuracy, closed center, flow divider-combinervalve
104
FSBA High accuracy, closed center, flow divider-combinervalve
105
FSDG High accuracy, closed center, flow divider-combinervalve
106
FSEG High accuracy, closed center, flow divider-combinervalve
107
FSFG High accuracy, closed center, flow divider-combinervalve
108
FSCH High capacity, closed center, flow divider-combinervalve
109
FSDH High capacity, closed center, flow divider-combinervalve
110
FSEH High capacity, closed center, flow divider-combinervalve
111
FSFH High capacity, closed center, flow divider-combinervalve
112
FSCS Synchronizing, flow divider-combinervalve
113
FSDS Synchronizing, flow divider-combinervalve
114
FSES Synchronizing, flow divider-combinervalve
115
FSFS Synchronizing, flow divider-combinervalve
116
FSAS High accuracy synchronizing, flow divider-combinervalve
117
FSBS High accuracy synchronizing, flow divider-combinervalve
118
FSDR High accuracy synchronizing, flow divider-combinervalve
119
FSER High accuracy synchronizing, flow divider-combinervalve
120
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Table of Contents
FSFR High accuracy synchronizing, flow divider-combinervalve
121
LRBC Normally closed, modulatingelement
122
LRDC Normally closed, modulatingelement
123
LRFC Normally closed, modulatingelement
124
LRHC Normally closed, modulatingelement
125
LRJC Normally closed, modulatingelement
126
LRBA Normally closed, modulating element with pilot source from port1
127
LRDA Normally closed, modulating element with pilot source from port1
128
LRFA Normally closed, modulating element with pilot source from port1
129
LRHA Normally closed, modulating element with pilot source from port1
130
LRJA Normally closed, modulating element with pilot source from port1
131
LRDS Normally closed modulating element withshuttle
132
LPBC Normally open, modulatingelement
133
LPDC Normally open, modulatingelement
134
LPFC Normally open, modulatingelement
135
LPFCL Tuneable, normally open modulatingelement
136
LPHC Normally open, modulatingelement
137
LPJC Normally open, modulatingelement
138
LPBA Normally open, modulating element with pilot source from port1
139
LPDA Normally open, modulating element with pilot source from port1
140
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Table of Contents
LPFA Normally open, modulating element with pilot source from port1
141
LPHA Normally open, modulating element with pilot source from port1
142
LPJA Normally open, modulating element with pilot source from port1
143
LPJA8 Normally open, modulating element with integral T-8A control cavity and pilot sourcefrom port 1
144
LPDS Normally open modulating element withshuttle
145
LHDT Normally open, bi-directional, modulatingelement
146
LHFT Normally open, bi-directional, modulatingelement
147
LHHT Normally open, bi-directional, modulatingelement
148
LHDA Bypass/restrictive, priority modulatingelement
149
LHFA Bypass/restrictive, priority modulatingelement
150
LHHA Bypass/restrictive, priority modulatingelement
151
LHJA Bypass/restrictive, priority modulatingelement
152
RVBB Normally closed modulating element valve with relieffunction
153
RVCB Normally closed modulating element valve with relieffunction
154
RVEB Normally closed modulating element valve with relieffunction
155
RVGB Normally closed modulating element valve with relieffunction
156
RVIB Normally closed modulating element valve with relieffunction
157
LRFCL Tuneable, normally closed, modulatingelement
158
Cavity Information
Series Ports Cavities
Series Z Cartridges3/8-24 UNF Cartridge Thread5 mm Valve Hex Size11 - 14 Nm Valve Installation Torque
2-Port T-382A
Series P CartridgesM16 Cartridge Thread22,2 mm Valve Hex Size27 - 33 Nm Valve Installation Torque
2-Port2-Port (Deep)3-Port
T-8AT-8DPT-9A
Series 0 CartridgesM16 Cartridge Thread19,1 mm Valve Hex Size25,4 mm Valve Hex Size27 - 33 Nm Valve Installation Torque
2-Port2-Port (Deep)3-Port
T-162AT-162DPT-163A
Series 1 CartridgesM20 Cartridge Thread22,2 mm Valve Hex Size41 - 47 Nm Valve Installation Torque
2-Port2-Port3-Port4-Port4-Port6-Port
T-10AT-13AT-11AT-21AT-31AT-61A
Series 2 Cartridges1"-14 UNS Cartridge Thread28,6 mm Valve Hex Size61 - 68 Nm Valve Installation Torque
2-Port2-Port3-Port4-Port4-Port4-Port (Dual path)6-Port6-Port
T-3AT-5AT-2AT-22AT-32AT-52ADT-52AT-62A
Series 3 CartridgesM36 Cartridge Thread31,8 mm Valve Hex Size203 - 217 Nm Valve Installation Torque
2-Port3-Port4-Port4-Port4-Port (Dual path)6-Port6-Port
T-16AT-17AT-23AT-33AT-53ADT-53AT-63A
Series 4 CartridgesM48 Cartridge Thread41,3 mm Valve Hex Size474 - 508 Nm Valve Installation Torque
2-Port2-Port (Undercut)3-Port3-Port (Undercut)4-Port4-Port (Undercut)4-Port4-Port (Dual path)6-Port6-Port
T-18AT-18AUT-19AT-19AUT-24AT-24AUT-34AT-54ADT-54AT-64A
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 1 of 158
MODELFQBA
Fixed orifice, flow fuse valveCAPACITY: 8,5 L/min. / CAVITY: T-162A
Flow fuse cartridges are used to maintain the position of a hydraulic actuator in the event of a hose or line break.The valve allows flow to and from the actuator but closes instantly if flow from the actuator exceeds the setting ofthe valve. NOTE: Because the valve responds so rapidly, it is sensitive to any transient flow above the valvesetting.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 15 cc/min.@70 barSeal kit - Cartridge Buna: 990162007Seal kit - Cartridge Polyurethane: 990162002Seal kit - Cartridge Viton: 990162006
(X)CONTROLX Not Adjustable
(A)SETTING RANGEA Replaceable Orifice .5 - 2.25 gpm (2 -
8,5 L/min.)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FQBA
Model Code Example: FQBAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 2 of 158
MODELFQCA
Fixed orifice, flow fuse valveSERIES 1 / CAPACITY: 23 L/min. / CAVITY: T-13A
Flow fuse cartridges are used to maintain the position of a hydraulic actuator in the event of a hose or line break.The valve allows flow to and from the actuator but closes instantly if flow from the actuator exceeds the setting ofthe valve. NOTE: Because the valve responds so rapidly, it is sensitive to any transient flow above the valvesetting.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barSeal kit - Cartridge Buna: 990010007Seal kit - Cartridge Polyurethane: 990010002Seal kit - Cartridge Viton: 990010006
(X)CONTROLX Not Adjustable
(A)SETTING RANGEA Replaceable Orifice .5 - 6 gpm (2 - 23
L/min.)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FQCA
Model Code Example: FQCAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 3 of 158
MODELFQEA
Fixed orifice, flow fuse valveSERIES 2 / CAPACITY: 60 L/min. / CAVITY: T-5A
Flow fuse cartridges are used to maintain the position of a hydraulic actuator in the event of a hose or line break.The valve allows flow to and from the actuator but closes instantly if flow from the actuator exceeds the setting ofthe valve. NOTE: Because the valve responds so rapidly, it is sensitive to any transient flow above the valvesetting.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 50 cc/min.@70 barSeal kit - Cartridge Buna: 990203007Seal kit - Cartridge Viton: 990203006
(X)CONTROLX Not Adjustable
(A)SETTING RANGEA Replaceable Orifice 1 - 15 gpm (4 - 60
L/min.)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FQEA
Model Code Example: FQEAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 4 of 158
MODELFQGA
Fixed orifice, flow fuse valveSERIES 3 / CAPACITY: 95 L/min. / CAVITY: T-16A
Flow fuse cartridges are used to maintain the position of a hydraulic actuator in the event of a hose or line break.The valve allows flow to and from the actuator but closes instantly if flow from the actuator exceeds the setting ofthe valve. NOTE: Because the valve responds so rapidly, it is sensitive to any transient flow above the valvesetting.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 65 cc/min.@70 barSeal kit - Cartridge Buna: 990016007Seal kit - Cartridge Polyurethane: 990016002Seal kit - Cartridge Viton: 990016006
(X)CONTROLX Not Adjustable
(A)SETTING RANGEA Replaceable Orifice 1 - 25 gpm (4 - 95
L/min.)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FQGA
Model Code Example: FQGAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 5 of 158
MODELFQIA
Fixed orifice, flow fuse valveSERIES 4 / CAPACITY: 200 L/min. / CAVITY: T-18A
Flow fuse cartridges are used to maintain the position of a hydraulic actuator in the event of a hose or line break.The valve allows flow to and from the actuator but closes instantly if flow from the actuator exceeds the setting ofthe valve. NOTE: Because the valve responds so rapidly, it is sensitive to any transient flow above the valvesetting.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 80 cc/min.@70 barSeal kit - Cartridge Buna: 990018007Seal kit - Cartridge Polyurethane: 990018002Seal kit - Cartridge Viton: 990018006
(X)CONTROLX Not Adjustable
(A)SETTING RANGEA Replaceable Orifice 1 - 50 gpm (4 - 200
L/min.)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FQIA
Model Code Example: FQIAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 6 of 158
MODELNFBC
Fully adjustable needle valveCAPACITY: 20 L/min. (4 mm) / CAVITY: T-162A
Needle valves are fully adjustable orifices used to regulate flow. They are infinitely adjustable from fully closed up tothe maximum orifice diameter. They are not pressure compensated and may be used as flow controls or as shutoffvalves.
TECHNICAL DATAMaximum Operating Pressure 350 barAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990162007Seal kit - Cartridge EPDM: 990162014Seal kit - Cartridge Polyurethane: 990162002Seal kit - Cartridge Viton: 990162006
(L)CONTROLL Standard Screw AdjustmentK HandknobW Hex Wrench Adjustment
(C)MAXIMUM ORIFICE DIAMETERC .16 in. (4 mm)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NFBC
Model Code Example: NFBCLCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 7 of 158
MODELNFCC
Fully adjustable needle valveSERIES 1 / CAPACITY: 28 L/min. (4,8 mm) / CAVITY: T-13A
Needle valves are fully adjustable orifices used to regulate flow. They are infinitely adjustable from fully closed up tothe maximum orifice diameter. They are not pressure compensated and may be used as flow controls or as shutoffvalves.
TECHNICAL DATAMaximum Operating Pressure 350 barAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990010007Seal kit - Cartridge EPDM: 990010014Seal kit - Cartridge Polyurethane: 990010002Seal kit - Cartridge Viton: 990010006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob, Flow Control
(C)MAXIMUM ORIFICE DIAMETERC .19 in. (4,8 mm)D .09 in. (2,3 mm)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NFCC
For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.NOTES
Model Code Example: NFCCLCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 8 of 158
MODELNFCD
Fully adjustable needle valveSERIES 1 / CAPACITY: 80 L/min. (8,4 mm) / CAVITY: T-13A
Needle valves are fully adjustable orifices used to regulate flow. They are infinitely adjustable from fully closed up tothe maximum orifice diameter. They are not pressure compensated and may be used as flow controls or as shutoffvalves.
TECHNICAL DATAMaximum Operating Pressure 350 barAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990010007Seal kit - Cartridge EPDM: 990010014Seal kit - Cartridge Polyurethane: 990010002Seal kit - Cartridge Viton: 990010006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(F)MAXIMUM ORIFICE DIAMETERF .33 in. (8,4 mm)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NFCD
For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.NOTES
Model Code Example: NFCDLFNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 9 of 158
MODELNFDC
Fully adjustable needle valveSERIES 2 / CAPACITY: 45 L/min. (6,4 mm) / CAVITY: T-5A
Needle valves are fully adjustable orifices used to regulate flow. They are infinitely adjustable from fully closed up tothe maximum orifice diameter. They are not pressure compensated and may be used as flow controls or as shutoffvalves.
TECHNICAL DATAMaximum Operating Pressure 350 barAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990203007Seal kit - Cartridge EPDM: 990203014Seal kit - Cartridge Viton: 990203006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(A)MAXIMUM ORIFICE DIAMETERA .25 in. (6,4 mm)B .12 in. (3,0 mm)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NFDC
For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.NOTES
Model Code Example: NFDCLANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 10 of 158
MODELNFDD
Fully adjustable needle valveSERIES 2 / CAPACITY: 200 L/min. (12,7 mm) / CAVITY: T-5A
Needle valves are fully adjustable orifices used to regulate flow. They are infinitely adjustable from fully closed up tothe maximum orifice diameter. They are not pressure compensated and may be used as flow controls or as shutoffvalves.
TECHNICAL DATAMaximum Operating Pressure 350 barAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990203007Seal kit - Cartridge Polyurethane: 990203014Seal kit - Cartridge Viton: 990203006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(G)MAXIMUM ORIFICE DIAMETERG .5 in. (12,7 mm)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NFDD
For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.NOTES
Model Code Example: NFDDLGNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 11 of 158
MODELNFEC
Fully adjustable needle valveSERIES 3 / CAPACITY: 120 L/min. (9,7 mm) / CAVITY: T-16A
Needle valves are fully adjustable orifices used to regulate flow. They are infinitely adjustable from fully closed up tothe maximum orifice diameter. They are not pressure compensated and may be used as flow controls or as shutoffvalves.
TECHNICAL DATAMaximum Operating Pressure 350 barAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990016007Seal kit - Cartridge EPDM: 990016014Seal kit - Cartridge Polyurethane: 990016002Seal kit - Cartridge Viton: 990016006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(E)MAXIMUM ORIFICE DIAMETERE .38 in. (9,7 mm)F .28 in. (7,1 mm)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NFEC
Model Code Example: NFECLENCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 12 of 158
MODELNFED
Fully adjustable needle valveSERIES 3 / CAPACITY: 340 L/min. (17,5 mm) / CAVITY: T-16A
Needle valves are fully adjustable orifices used to regulate flow. They are infinitely adjustable from fully closed up tothe maximum orifice diameter. They are not pressure compensated and may be used as flow controls or as shutoffvalves.
TECHNICAL DATAMaximum Operating Pressure 350 barAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990016007Seal kit - Cartridge EPDM: 990016014Seal kit - Cartridge Polyurethane: 990016002Seal kit - Cartridge Viton: 990016006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(H)MAXIMUM ORIFICE DIAMETERH .69 in. (17,5 mm)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NFED
Model Code Example: NFEDLHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 13 of 158
MODELNFFC
Fully adjustable needle valveSERIES 4 / CAPACITY: 240 L/min. (14,2 mm) / CAVITY: T-18A
Needle valves are fully adjustable orifices used to regulate flow. They are infinitely adjustable from fully closed up tothe maximum orifice diameter. They are not pressure compensated and may be used as flow controls or as shutoffvalves.
TECHNICAL DATAMaximum Operating Pressure 350 barAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990018007Seal kit - Cartridge EPDM: 990018014Seal kit - Cartridge Polyurethane: 990018002Seal kit - Cartridge Viton: 990018006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob, Flow Control
(G)MAXIMUM ORIFICE DIAMETERG .56 in. (14,2 mm)H .38 in. (9,7 mm)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/NFFC
Model Code Example: NFFCLGNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 14 of 158
MODELNFFD
Fully adjustable needle valveSERIES 4 / CAPACITY: 530 L/min. (21,6 mm) / CAVITY: T-18A
Needle valves are fully adjustable orifices used to regulate flow. They are infinitely adjustable from fully closed up tothe maximum orifice diameter. They are not pressure compensated and may be used as flow controls or as shutoffvalves.
TECHNICAL DATAMaximum Operating Pressure 350 barAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990018007Seal kit - Cartridge EPDM: 990018014Seal kit - Cartridge Polyurethane: 990018002Seal kit - Cartridge Viton: 990018006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobR Capped Screw AdjustmentY Tri-Grip Handknob
(I)MAXIMUM ORIFICE DIAMETERI .85 in. (21,6 mm)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NFFD
Model Code Example: NFFDLINCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 15 of 158
MODELNCBB
Fully adjustable needle valve with reverse flow checkCAPACITY: 20 L/min. (4 mm) / CAVITY: T-162A
Needle valves with reverse-flow check are fully adjustable orifices used to regulate flow. They are infinitelyadjustable from fully closed up to the maximum orifice diameter. An integral high-capacity check valve providesunrestricted flow from port 2 to port 1. They are not pressure compensated.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 0,7 cc/min.Adjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990162007Seal kit - Cartridge Polyurethane: 990162002Seal kit - Cartridge Viton: 990162006
(L)CONTROLL Standard Screw AdjustmentK Handknob
(C)REVERSE FLOW CHECKC 30 psi (2 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NCBB
Model Code Example: NCBBLCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 16 of 158
MODELNCCB
Fully adjustable needle valve with reverse flow checkSERIES 1 / CAPACITY: 28 L/min. (4,8 mm) / CAVITY: T-13A
Needle valves with reverse-flow check are fully adjustable orifices used to regulate flow. They are infinitelyadjustable from fully closed up to the maximum orifice diameter. An integral high-capacity check valve providesunrestricted flow from port 2 to port 1. They are not pressure compensated.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 0,7 cc/min.Adjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990010007Seal kit - Cartridge EPDM: 990010014Seal kit - Cartridge Polyurethane: 990010002Seal kit - Cartridge Viton: 990010006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobR Capped Screw AdjustmentY Tri-Grip Handknob
(C)REVERSE FLOW CHECKC 30 psi (2 bar)A 4 psi (0,3 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NCCB
For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.NOTES
Model Code Example: NCCBLCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 17 of 158
MODELNCCC
Fully adjustable needle valve with reverse flow checkSERIES 1 / CAPACITY: 8 L/min. (2,3 mm) / CAVITY: T-13A
Needle valves with reverse-flow check are fully adjustable orifices used to regulate flow. They are infinitelyadjustable from fully closed up to the maximum orifice diameter. An integral high-capacity check valve providesunrestricted flow from port 2 to port 1. They are not pressure compensated.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 0,3 cc/min.Adjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990010007Seal kit - Cartridge Polyurethane: 990010002Seal kit - Cartridge Viton: 990010006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobO Handknob with Panel MountR Capped Screw AdjustmentY Tri-Grip Handknob
(C)REVERSE FLOW CHECKC 30 psi (2 bar)A 4 psi (0,3 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NCCC
For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.NOTES
Model Code Example: NCCCLCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 18 of 158
MODELNCCD
Fully adjustable needle valve with reverse flow checkSERIES 1 / CAPACITY: 4 L/min. (1,5 mm) / CAVITY: T-13A
Needle valves with reverse-flow check are fully adjustable orifices used to regulate flow. They are infinitelyadjustable from fully closed up to the maximum orifice diameter. An integral high-capacity check valve providesunrestricted flow from port 2 to port 1. They are not pressure compensated.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 0,3 cc/min.Adjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990010007Seal kit - Cartridge Polyurethane: 990010002Seal kit - Cartridge Viton: 990010006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobO Handknob with Panel MountR Capped Screw AdjustmentY Tri-Grip Handknob
(A)REVERSE FLOW CHECKA 4 psi (0,3 bar)B 15 psi (1 bar)C 30 psi (2 bar)D 50 psi (3,5 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NCCD
For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.NOTES
Model Code Example: NCCDLANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 19 of 158
MODELNCEB
Fully adjustable needle valve with reverse flow checkSERIES 2 / CAPACITY: 45 L/min. (6,4 mm) / CAVITY: T-5A
Needle valves with reverse-flow check are fully adjustable orifices used to regulate flow. They are infinitelyadjustable from fully closed up to the maximum orifice diameter. An integral high-capacity check valve providesunrestricted flow from port 2 to port 1. They are not pressure compensated.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 0,7 cc/min.Adjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990203007Seal kit - Cartridge EPDM: 990203014Seal kit - Cartridge Viton: 990203006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(C)REVERSE FLOW CHECKC 30 psi (2 bar)A 4 psi (0,3 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NCEB
For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.NOTES
Model Code Example: NCEBLCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 20 of 158
MODELNCEC
Fully adjustable needle valve with reverse flow checkSERIES 2 / CAPACITY: 11 L/min. (3,3 mm) / CAVITY: T-5A
Needle valves with reverse-flow check are fully adjustable orifices used to regulate flow. They are infinitelyadjustable from fully closed up to the maximum orifice diameter. An integral high-capacity check valve providesunrestricted flow from port 2 to port 1. They are not pressure compensated.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 0,3 cc/min.Adjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990203007Seal kit - Cartridge Viton: 990203006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(C)REVERSE FLOW CHECKC 30 psi (2 bar)A 4 psi (0,3 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/LH Mild Steel, Zinc-Nickel
snhy.com/NCEC
For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.NOTES
Model Code Example: NCECLCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 21 of 158
MODELNCFB
Fully adjustable needle valve with reverse flow checkSERIES 3 / CAPACITY: 120 L/min. (9,7 mm) / CAVITY: T-16A
Needle valves with reverse-flow check are fully adjustable orifices used to regulate flow. They are infinitelyadjustable from fully closed up to the maximum orifice diameter. An integral high-capacity check valve providesunrestricted flow from port 2 to port 1. They are not pressure compensated.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 0,7 cc/min.Adjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990016007Seal kit - Cartridge Polyurethane: 990016002Seal kit - Cartridge Viton: 990016006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(C)REVERSE FLOW CHECKC 30 psi (2 bar)A 4 psi (0,3 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NCFB
Model Code Example: NCFBLCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 22 of 158
MODELNCFC
Fully adjustable needle valve with reverse flow checkSERIES 3 / CAPACITY: 60 L/min. (7,1 mm) / CAVITY: T-16A
Needle valves with reverse-flow check are fully adjustable orifices used to regulate flow. They are infinitelyadjustable from fully closed up to the maximum orifice diameter. An integral high-capacity check valve providesunrestricted flow from port 2 to port 1. They are not pressure compensated.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 0,3 cc/min.Adjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990016007Seal kit - Cartridge Polyurethane: 990016002Seal kit - Cartridge Viton: 990016006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(C)REVERSE FLOW CHECKC 30 psi (2 bar)A 4 psi (0,3 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NCFC
Model Code Example: NCFCLCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 23 of 158
MODELNCGB
Fully adjustable needle valve with reverse flow checkSERIES 4 / CAPACITY: 240 L/min. (14,2 mm) / CAVITY: T-18A
Needle valves with reverse-flow check are fully adjustable orifices used to regulate flow. They are infinitelyadjustable from fully closed up to the maximum orifice diameter. An integral high-capacity check valve providesunrestricted flow from port 2 to port 1. They are not pressure compensated.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 0,7 cc/min.Adjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990018007Seal kit - Cartridge EPDM: 990018014Seal kit - Cartridge Polyurethane: 990018002Seal kit - Cartridge Viton: 990018006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(C)REVERSE FLOW CHECKC 30 psi (2 bar)A 4 psi (0,3 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/NCGB
Model Code Example: NCGBLCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 24 of 158
MODELNCGC
Fully adjustable needle valve with reverse flow checkSERIES 4 / CAPACITY: 120 L/min. (9,7 mm) / CAVITY: T-18A
Needle valves with reverse-flow check are fully adjustable orifices used to regulate flow. They are infinitelyadjustable from fully closed up to the maximum orifice diameter. An integral high-capacity check valve providesunrestricted flow from port 2 to port 1. They are not pressure compensated.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 0,3 cc/min.Adjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990018007Seal kit - Cartridge Polyurethane: 990018002Seal kit - Cartridge Viton: 990018006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(C)REVERSE FLOW CHECKC 30 psi (2 bar)A 4 psi (0,3 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/NCGC
Model Code Example: NCGCLCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 25 of 158
MODELNFAB
Fully adjustable needle valve - pilot capacitySERIES P / CAPACITY: 0,8 L/min. (0,9 mm) / CAVITY: T-8A
Two-port, pilot-stage needle valves are fully adjustable devices used to regulate pilot flow in a main-stage valve orto meter in/out flow in low flow applications. These cartridges are designed for pilot flow applications and utilizeSun's T-8A cavity so they can be used in conjunction with Sun's pilot-operated, main-stage valves.
TECHNICAL DATAMaximum Operating Pressure 350 barAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 3Effective Orifice Size 0,9 mmSeal kit - Cartridge Buna: 990008007Seal kit - Cartridge EPDM: 990008014Seal kit - Cartridge Polyurethane: 990008002Seal kit - Cartridge Viton: 990008006
(K)CONTROLK Handknob
(X)MAXIMUM ORIFICE DIAMETERX .03 in. (0,8 mm)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/NFAB
Model Code Example: NFABKXNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 26 of 158
MODELCNAC
Fixed orifice, non-pressure compensated, flow control valve with reverse flowcheckCAPACITY: 30 L/min. / CAVITY: T-162A
This valve is a fixed-orifice, non-pressure-compensated flow control with a reverse flow check. The flow setting isspecified by the user and is set at the factory.
TECHNICAL DATAMaximum Operating Pressure 350 barOrifice Range 0,4 - 1,6 mmSeal kit - Cartridge Buna: 990162007Seal kit - Cartridge Polyurethane: 990162002Seal kit - Cartridge Viton: 990162006
(X)CONTROLX Not Adjustable
(C)SETTING RANGEC 30 psi (2 bar) Cracking Pressure, .016 -
.062 in. (0,4 - 1,6 mm)A 4 psi (0,3 bar) Cracking Pressure, .016
- .062 in. (0,4 - 1,6 mm)E 75 psi (5 bar) Cracking Pressure, .016 -
.062 in. (0,4 - 1,6 mm)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/CNAC
Model Code Example: CNACXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 27 of 158
MODELCNCC
Fixed orifice, non-pressure compensated, flow control valve with reverse flowcheckSERIES 1 / CAPACITY: 60 L/min. / CAVITY: T-13A
This valve is a fixed-orifice, non-pressure-compensated flow control with a reverse flow check. The flow setting isspecified by the user and is set at the factory.
TECHNICAL DATAMaximum Operating Pressure 350 barOrifice Range 0,4 - 3,9 mmSeal kit - Cartridge Buna: 990010007Seal kit - Cartridge Polyurethane: 990010002Seal kit - Cartridge Viton: 990010006
(X)CONTROLX Not Adjustable
(C)SETTING RANGEC 30 psi (2 bar) Cracking Pressure, .016 -
.153 in. (0,4 - 3,9 mm)A 4 psi (0,3 bar) Cracking Pressure, .016
- .153 in. (0,4 - 3,9 mm)B 15 psi (1 bar) Cracking Pressure, .016 -
.153 in. (0,4 - 3,9 mm)D 50 psi (3,5 bar) Cracking Pressure,
.016 - .153 in. (0,4 - 3,9 mm)E 75 psi (5 bar) Cracking Pressure, .016 -
.153 in. (0,4 - 3,9 mm)F 100 psi (7 bar) Cracking Pressure, .016
- .153 in. (0,4 - 3,9 mm)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/CNCC
Model Code Example: CNCCXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 28 of 158
MODELCNEC
Fixed orifice, non-pressure compensated, flow control valve with reverse flowcheckSERIES 2 / CAPACITY: 120 L/min. / CAVITY: T-5A
This valve is a fixed-orifice, non-pressure-compensated flow control with a reverse flow check. The flow setting isspecified by the user and is set at the factory.
TECHNICAL DATAMaximum Operating Pressure 350 barOrifice Range 0,4 - 3,4 mmSeal kit - Cartridge Buna: 990203007Seal kit - Cartridge Viton: 990203006
(X)CONTROLX Not Adjustable
(C)SETTING RANGEC 30 psi (2 bar) Cracking Pressure, .016 -
.135 in. (0,4 - 3,4 mm)A 4 psi (0,3 bar) Cracking Pressure, .016
- .135 in. (0,4 - 3,4 mm)B 15 psi (1 bar) Cracking Pressure, .016 -
.135 in. (0,4 - 3,4 mm)D 50 psi (3,5 bar) Cracking Pressure,
.016 - .135 in. (0,4 - 3,4 mm)E 75 psi (5 bar) Cracking Pressure, .016 -
.135 in. (0,4 - 3,4 mm)F 100 psi (7 bar) Cracking Pressure, .016
- .135 in. (0,4 - 3,4 mm)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/CNEC
Model Code Example: CNECXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 29 of 158
MODELCNGC
Fixed orifice, non-pressure compensated, flow control valve with reverse flowcheckSERIES 3 / CAPACITY: 240 L/min. / CAVITY: T-16A
This valve is a fixed-orifice, non-pressure-compensated flow control with a reverse flow check. The flow setting isspecified by the user and is set at the factory.
TECHNICAL DATAMaximum Operating Pressure 350 barOrifice Range 0,4 - 5,5 mmSeal kit - Cartridge Buna: 990016007Seal kit - Cartridge Polyurethane: 990016002Seal kit - Cartridge Viton: 990016006
(X)CONTROLX Not Adjustable
(C)SETTING RANGEC 30 psi (2 bar) Cracking Pressure, .016 -
.218 in. (0,4 - 5,5 mm)A 4 psi (0,3 bar) Cracking Pressure, .016
- .218 in. (0,4 - 5,5 mm)B 15 psi (1 bar) Cracking Pressure, .016 -
.218 in. (0,4 - 5,5 mm)D 50 psi (3,5 bar) Cracking Pressure,
.016 - .218 in. (0,4 - 5,5 mm)E 75 psi (5 bar) Cracking Pressure, .016 -
.218 in. (0,4 - 5,5 mm)F 100 psi (7 bar) Cracking Pressure, .016
- .218 in. (0,4 - 5,5 mm)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/CNGC
Model Code Example: CNGCXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 30 of 158
MODELCNIC
Fixed orifice, non-pressure compensated, flow control valve with reverse flowcheckSERIES 4 / CAPACITY: 480 L/min. / CAVITY: T-18A
This valve is a fixed-orifice, non-pressure-compensated flow control with a reverse flow check. The flow setting isspecified by the user and is set at the factory.
TECHNICAL DATAMaximum Operating Pressure 350 barOrifice Range 0,4 - 5,5 mmSeal kit - Cartridge Buna: 990018007Seal kit - Cartridge Polyurethane: 990018002Seal kit - Cartridge Viton: 990018006
(X)CONTROLX Not Adjustable
(C)SETTING RANGEC 30 psi (2 bar) Cracking Pressure, .016 -
.218 in. (0,4 - 5,5 mm)A 4 psi (0,3 bar) Cracking Pressure, .016
- .218 in. (0,4 - 5,5 mm)B 15 psi (1 bar) Cracking Pressure, .016 -
.218 in. (0,4 - 5,5 mm)D 50 psi (3,5 bar) Cracking Pressure,
.016 - .218 in. (0,4 - 5,5 mm)E 75 psi (5 bar) Cracking Pressure, .016 -
.218 in. (0,4 - 5,5 mm)F 100 psi (7 bar) Cracking Pressure, .016
- .218 in. (0,4 - 5,5 mm)
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/CNIC
Model Code Example: CNICXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 31 of 158
MODELFXAA
Fixed orifice, pressure compensated flow control valveSERIES P / CAPACITY: 2 L/min. / CAVITY: T-8A
Fixed-orifice, pressure-compensated flow controls provide precise flow regulation for meter-in or meter-outapplications where there may be wide pressure fluctuations. A variety of flow rates are available.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990008007Seal kit - Cartridge EPDM: 990008014Seal kit - Cartridge Polyurethane: 990008002Seal kit - Cartridge Viton: 990008006
(X)CONTROLX Not Adjustable
(A)FLOW RATEA 15 in³/min. (250 cc/min.)B 20 in³/min. (330 cc/min.)D 40 in³/min. (660 cc/min.)F 60 in³/min. (1 L/min.)H 80 in³/min. (1.3 L/min.)J 100 in³/min. (1.6 L/min.)L 120 in³/min. (2.0 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FXAA
Model Code Example: FXAAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 32 of 158
MODELFXAG
Flush mount, pressure compensated flow controlSERIES P / CAPACITY: 2 L/min. / CAVITY: T-8A
Fixed-orifice, pressure-compensated flow controls provide precise flow regulation for meter-in or meter-outapplications where there may be wide pressure fluctuations. A variety of flow rates are available.
TECHNICAL DATAMaximum Operating Pressure 350 barValve Internal Hex Size 8 mmSeal kit - Cartridge Buna: 990008007Seal kit - Cartridge Polyurethane: 990008002Seal kit - Cartridge Viton: 990008006
(X)CONTROLX Not Adjustable
(A)FLOW RATEA 15 in³/min. (250 cc/min.)B 20 in³/min. (330 cc/min.)D 40 in³/min. (660 cc/min.)F 60 in³/min. (1 L/min.)H 80 in³/min. (1.3 L/min.)J 100 in³/min. (1.6 L/min.)L 120 in³/min. (2.0 L/min.)
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FXAG
Model Code Example: FXAGXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 33 of 158
MODELFXAM
Insert style, pressure compensated flow controlSERIES P / CAPACITY: 2 L/min. / CAVITY: T-8DP
Fixed-orifice, pressure-compensated flow controls provide precise flow regulation for meter-in or meter-outapplications where there may be wide pressure fluctuations. A variety of flow rates are available. The THRU port atthe top of the valve can be used as the outlet with port 2 blocked. See cavity drawing for details.
TECHNICAL DATAMaximum Operating Pressure 350 barValve Internal Hex Size 8 mm
(X)CONTROLX Not Adjustable
(A)FLOW RATEA 15 in³/min. (250 cc/min.)B 20 in³/min. (330 cc/min.)D 40 in³/min. (660 cc/min.)F 60 in³/min. (1 L/min.)H 80 in³/min. (1.3 L/min.)J 100 in³/min. (1.6 L/min.)L 120 in³/min. (2.0 L/min.)
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FXAM
Model Code Example: FXAMXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 34 of 158
MODELFXBA
Fixed orifice, pressure compensated flow control valveCAPACITY: 11 L/min. / CAVITY: T-162A
Fixed-orifice, pressure-compensated flow controls provide precise flow regulation for meter-in or meter-outapplications where there may be wide pressure fluctuations. The flow setting is specified by the user and is set atthe factory.
TECHNICAL DATAMaximum Operating Pressure 350 barLocknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990162007Seal kit - Cartridge EPDM: 990162014Seal kit - Cartridge Polyurethane: 990162002Seal kit - Cartridge Viton: 990162006
(X)CONTROLX Not AdjustableL Tuning AdjustmentK Handknob
(A)SETTING RANGEA Replaceable Orifice .1 - 3 gpm (0,4 - 11
L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FXBA
Model Code Example: FXBAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 35 of 158
MODELFXCA
Fixed orifice, pressure compensated flow control valveSERIES 1 / CAPACITY: 23 L/min. / CAVITY: T-13A
Fixed-orifice, pressure-compensated flow controls provide precise flow regulation for meter-in or meter-outapplications where there may be wide pressure fluctuations. The flow setting is specified by the user and is set atthe factory.
TECHNICAL DATAMaximum Operating Pressure 350 barLocknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990010007Seal kit - Cartridge EPDM: 990010014Seal kit - Cartridge Polyurethane: 990010002Seal kit - Cartridge Viton: 990010006
(X)CONTROLX Not AdjustableL Tuning AdjustmentK Handknob
(A)SETTING RANGEA Replaceable Orifice .1 - 6 gpm (0,4 - 23
L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FXCA
Model Code Example: FXCAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 36 of 158
MODELFXDA
Fixed orifice, pressure compensated flow control valveSERIES 2 / CAPACITY: 45 L/min. / CAVITY: T-5A
Fixed-orifice, pressure-compensated flow controls provide precise flow regulation for meter-in or meter-outapplications where there may be wide pressure fluctuations. The flow setting is specified by the user and is set atthe factory.
TECHNICAL DATAMaximum Operating Pressure 350 barLocknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990203007Seal kit - Cartridge EPDM: 990203014Seal kit - Cartridge Viton: 990203006
(X)CONTROLX Not AdjustableL Tuning AdjustmentK Handknob
(A)SETTING RANGEA Replaceable Orifice .1 - 12 gpm (0,4 -
45 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FXDA
Model Code Example: FXDAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 37 of 158
MODELFXEA
Fixed orifice, pressure compensated flow control valveSERIES 3 / CAPACITY: 95 L/min. / CAVITY: T-16A
Fixed-orifice, pressure-compensated flow controls provide precise flow regulation for meter-in or meter-outapplications where there may be wide pressure fluctuations. The flow setting is specified by the user and is set atthe factory.
TECHNICAL DATAMaximum Operating Pressure 350 barLocknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990016007Seal kit - Cartridge EPDM: 990016014Seal kit - Cartridge Polyurethane: 990016002Seal kit - Cartridge Viton: 990016006
(L)CONTROLL Tuning AdjustmentC Tamper Resistant - Factory SetK HandknobX Not Adjustable
(A)SETTING RANGEA Replaceable Orifice .2 - 25 gpm (0,8 -
95 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FXEA
Model Code Example: FXEALANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 38 of 158
MODELFXFA
Fixed orifice, pressure compensated flow control valveSERIES 4 / CAPACITY: 200 L/min. / CAVITY: T-18A
Fixed-orifice, pressure-compensated flow controls provide precise flow regulation for meter-in or meter-outapplications where there may be wide pressure fluctuations. The flow setting is specified by the user and is set atthe factory.
TECHNICAL DATAMaximum Operating Pressure 350 barLocknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990018007Seal kit - Cartridge EPDM: 990018014Seal kit - Cartridge Polyurethane: 990018002Seal kit - Cartridge Viton: 990018006
(X)CONTROLX Not AdjustableL Tuning AdjustmentK Handknob
(A)SETTING RANGEA Replaceable Orifice .2 - 50 gpm (1 -
200 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FXFA
Model Code Example: FXFAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 39 of 158
MODELFCBB
Fixed orifice pressure compensated flow control valve with reverse flow checkCAPACITY: 11 L/min. / CAVITY: T-162A
Fixed-orifice, pressure-compensated flow controls with reverse-flow check provide precise flow regulation formeter-in or meter-out applications where there may be wide pressure fluctuations. An integral high-capacity checkvalve provides unrestricted flow from port 2 to port 1. The flow setting is specified by the user and is set at thefactory.
TECHNICAL DATAMaximum Operating Pressure 350 barLocknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990162007Seal kit - Cartridge Polyurethane: 990162002Seal kit - Cartridge Viton: 990162006
(X)CONTROLX Not AdjustableL Tuning AdjustmentK Handknob
(A)SETTING RANGEA Replaceable Orifice .1 - 3 gpm (0,4 - 11
L/min.)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FCBB
Model Code Example: FCBBXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 40 of 158
MODELFCCB
Fixed orifice pressure compensated flow control valve with reverse flow checkSERIES 1 / CAPACITY: 23 L/min. / CAVITY: T-13A
Fixed-orifice, pressure-compensated flow controls with reverse-flow check provide precise flow regulation formeter-in or meter-out applications where there may be wide pressure fluctuations. An integral high-capacity checkvalve provides unrestricted flow from port 2 to port 1. The flow setting is specified by the user and is set at thefactory.
TECHNICAL DATAMaximum Operating Pressure 350 barLocknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990010007Seal kit - Cartridge Polyurethane: 990010002Seal kit - Cartridge Viton: 990010006
(X)CONTROLX Not AdjustableL Tuning AdjustmentK Handknob
(A)SETTING RANGEA Replaceable Orifice .1 - 6 gpm (0,4 - 23
L/min.)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FCCB
Model Code Example: FCCBXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 41 of 158
MODELFCDB
Fixed orifice pressure compensated flow control valve with reverse flow checkSERIES 2 / CAPACITY: 45 L/min. / CAVITY: T-5A
Fixed-orifice, pressure-compensated flow controls with reverse-flow check provide precise flow regulation formeter-in or meter-out applications where there may be wide pressure fluctuations. An integral high-capacity checkvalve provides unrestricted flow from port 2 to port 1. The flow setting is specified by the user and is set at thefactory.
TECHNICAL DATAMaximum Operating Pressure 350 barLocknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990203007Seal kit - Cartridge Viton: 990203006
(X)CONTROLX Not AdjustableL Tuning AdjustmentK Handknob
(A)SETTING RANGEA Replaceable Orifice .1 - 12 gpm (0,4 -
45 L/min.)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FCDB
Model Code Example: FCDBXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 42 of 158
MODELFCEB
Fixed orifice pressure compensated flow control valve with reverse flow checkSERIES 3 / CAPACITY: 95 L/min. / CAVITY: T-16A
Fixed-orifice, pressure-compensated flow controls with reverse-flow check provide precise flow regulation formeter-in or meter-out applications where there may be wide pressure fluctuations. An integral high-capacity checkvalve provides unrestricted flow from port 2 to port 1. The flow setting is specified by the user and is set at thefactory.
TECHNICAL DATAMaximum Operating Pressure 350 barLocknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990016007Seal kit - Cartridge Polyurethane: 990016002Seal kit - Cartridge Viton: 990016006
(X)CONTROLX Not AdjustableL Tuning AdjustmentK Handknob
(A)SETTING RANGEA Replaceable Orifice .2 - 25 gpm (0,8 -
95 L/min.)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FCEB
Model Code Example: FCEBXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 43 of 158
MODELFCFB
Fixed orifice pressure compensated flow control valve with reverse flow checkSERIES 4 / CAPACITY: 200 L/min. / CAVITY: T-18A
Fixed-orifice, pressure-compensated flow controls with reverse-flow check provide precise flow regulation formeter-in or meter-out applications where there may be wide pressure fluctuations. An integral high-capacity checkvalve provides unrestricted flow from port 2 to port 1. The flow setting is specified by the user and is set at thefactory.
TECHNICAL DATAMaximum Operating Pressure 350 barLocknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990018007Seal kit - Cartridge Polyurethane: 990018002Seal kit - Cartridge Viton: 990018006
(X)CONTROLX Not AdjustableL Tuning AdjustmentK Handknob
(A)SETTING RANGEA Replaceable Orifice .2 - 50 gpm (1 -
200 L/min.)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FCFB
Model Code Example: FCFBXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 44 of 158
MODELFDBA
Fully adjustable pressure compensated flow control valve with reverse flowcheckSERIES 1 / CAPACITY: 23 L/min. / CAVITY: T-13A
Fully adjustable, pressure-compensated flow controls with reverse-flow check provide precise flow regulation formeter-in or meter-out applications where there may be wide pressure fluctuations. They are infinitely adjustablefrom nearly closed up to the maximum flow. An integral high-capacity check valve provides unrestricted flow fromport 2 to port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990010007Seal kit - Cartridge EPDM: 990010014Seal kit - Cartridge Polyurethane: 990010002Seal kit - Cartridge Viton: 990010006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(A)ADJUSTMENT RANGEA .1 - 6 gpm (0,4 - 23 L/min.)B .1 - 2 gpm (0,4 - 8 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FDBA
For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.NOTES
Model Code Example: FDBALANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 45 of 158
MODELFDCB
Fully adjustable pressure compensated flow control valve with reverse flowcheckSERIES 2 / CAPACITY: 45 L/min. / CAVITY: T-5A
Fully adjustable, pressure-compensated flow controls with reverse-flow check provide precise flow regulation formeter-in or meter-out applications where there may be wide pressure fluctuations. They are infinitely adjustablefrom nearly closed up to the maximum flow. An integral high-capacity check valve provides unrestricted flow fromport 2 to port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990203007Seal kit - Cartridge EPDM: 990203014Seal kit - Cartridge Viton: 990203006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(A)ADJUSTMENT RANGEA .1 - 12 gpm (0,4 - 45 L/min.)B .1 - 3 gpm (0,4 - 11 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/LH Mild Steel, Zinc-Nickel
snhy.com/FDCB
For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.NOTES
Model Code Example: FDCBLANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 46 of 158
MODELFDEA
Fully adjustable pressure compensated flow control valve with reverse flowcheckSERIES 3 / CAPACITY: 95 L/min. / CAVITY: T-16A
Fully adjustable, pressure-compensated flow controls with reverse-flow check provide precise flow regulation formeter-in or meter-out applications where there may be wide pressure fluctuations. They are infinitely adjustablefrom nearly closed up to the maximum flow. An integral high-capacity check valve provides unrestricted flow fromport 2 to port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990016007Seal kit - Cartridge EPDM: 990016014Seal kit - Cartridge Polyurethane: 990016002Seal kit - Cartridge Viton: 990016006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(A)ADJUSTMENT RANGEA .2 - 25 gpm (0,8 - 95 L/min.)B .2 - 16 gpm (0,8 - 60 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/LH Mild Steel, Zinc-Nickel
snhy.com/FDEA
Model Code Example: FDEALANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 47 of 158
MODELFDFA
Fully adjustable pressure compensated flow control valve with reverse flowcheckSERIES 4 / CAPACITY: 200 L/min. / CAVITY: T-18A
Fully adjustable, pressure-compensated flow controls with reverse-flow check provide precise flow regulation formeter-in or meter-out applications where there may be wide pressure fluctuations. They are infinitely adjustablefrom nearly closed up to the maximum flow. An integral high-capacity check valve provides unrestricted flow fromport 2 to port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990018007Seal kit - Cartridge EPDM: 990018014Seal kit - Cartridge Polyurethane: 990018002Seal kit - Cartridge Viton: 990018006
(L)CONTROLL Standard Screw AdjustmentH Calibrated Handknob with Detent LockK HandknobY Tri-Grip Handknob
(A)ADJUSTMENT RANGEA .2 - 50 gpm (1 - 200 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/LH Mild Steel, Zinc-Nickel
snhy.com/FDFA
Model Code Example: FDFALANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 48 of 158
MODELFXDA8
Ventable fixed orifice, pressure compensated flow control valve with integral T-8A control cavitySERIES 2 / CAPACITY: 45 L/min. / CAVITY: T-5A
This valve is a fixed-orifice, pressure-compensated flow control valve with an integral pilot control cavity. The pilotcontrol cavity will accept any T-8A pilot control cartridge. This type of valve provides precise flow regulation formeter-in or meter-out applications where there may be wide pressure fluctuations. The flow setting is specified bythe user and is set at the factory.
TECHNICAL DATAMaximum Operating Pressure 350 barPilot Control Cavity T-8ASeal kit - Cartridge Buna: 990203007Seal kit - Cartridge Viton: 990203006
(A)SETTING RANGEA Replaceable Orifice .1 - 12 gpm (0,4 -
45 L/min.)B Permanent Orifice .1 - 12 gpm (0,4 - 45
L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/FXDA8
Compound cartridge (pilot and main stage) assembly information is provided for reference only. Cartridges must be ordered separately and assembled atpoint of use.NOTES
Model Code Example: FXDA8ANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 49 of 158
MODELFRBA
Fixed orifice, bypass/restrictive, priority, flow control valveCAPACITY: 11 L/min. / CAVITY: T-163A
Bypass/restrictive, fixed-orifice, priority flow controls take an input flow at port 1 and use it to satisfy the priority flowat port 3. If the input flow exceeds the priority flow requirement, the excess is bypassed out port 2. The bypass flowmay be used in a secondary circuit.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Input Flow 30 L/min.Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990163007Seal kit - Cartridge Polyurethane: 990163002Seal kit - Cartridge Viton: 990163006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(A)SETTING RANGEA Replaceable Orifice .1 - 3 gpm (0,4 - 11
L/min.)
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FRBA
Model Code Example: FRBAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 50 of 158
MODELFRCA
Fixed orifice, bypass/restrictive, priority, flow control valveSERIES 1 / CAPACITY: 23 L/min. / CAVITY: T-11A
Bypass/restrictive, fixed-orifice, priority flow controls take an input flow at port 1 and use it to satisfy the priority flowat port 3. If the input flow exceeds the priority flow requirement, the excess is bypassed out port 2. The bypass flowmay be used in a secondary circuit.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Input Flow 60 L/min.Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990011007Seal kit - Cartridge Polyurethane: 990011002Seal kit - Cartridge Viton: 990011006
(X)CONTROLX Not AdjustableL Tuning AdjustmentK Handknob
(A)SETTING RANGEA Replaceable Orifice .1 - 6 gpm (0,4 - 23
L/min.)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FRCA
Model Code Example: FRCAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 51 of 158
MODELFRDA
Fixed orifice, bypass/restrictive, priority, flow control valveSERIES 2 / CAPACITY: 45 L/min. / CAVITY: T-2A
Bypass/restrictive, fixed-orifice, priority flow controls take an input flow at port 1 and use it to satisfy the priority flowat port 3. If the input flow exceeds the priority flow requirement, the excess is bypassed out port 2. The bypass flowmay be used in a secondary circuit.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Input Flow 120 L/min.Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990202007Seal kit - Cartridge EPDM: 990202014Seal kit - Cartridge Polyurethane: 990002002Seal kit - Cartridge Viton: 990202006
(X)CONTROLX Not AdjustableL Tuning AdjustmentK Handknob
(A)SETTING RANGEA Replaceable Orifice .1 - 12 gpm (0,4 -
45 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FRDA
For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.NOTES
Model Code Example: FRDAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 52 of 158
MODELFREA
Fixed orifice, bypass/restrictive, priority, flow control valveSERIES 3 / CAPACITY: 95 L/min. / CAVITY: T-17A
Bypass/restrictive, fixed-orifice, priority flow controls take an input flow at port 1 and use it to satisfy the priority flowat port 3. If the input flow exceeds the priority flow requirement, the excess is bypassed out port 2. The bypass flowmay be used in a secondary circuit.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Input Flow 240 L/min.Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990017007Seal kit - Cartridge Polyurethane: 990017002Seal kit - Cartridge Viton: 990017006
(X)CONTROLX Not AdjustableL Tuning AdjustmentK Handknob
(A)SETTING RANGEA Replaceable Orifice .2 - 25 gpm (0,8 -
95 L/min.)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FREA
Model Code Example: FREAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 53 of 158
MODELFRFA
Fixed orifice, bypass/restrictive, priority, flow control valveSERIES 4 / CAPACITY: 200 L/min. / CAVITY: T-19A
Bypass/restrictive, fixed-orifice, priority flow controls take an input flow at port 1 and use it to satisfy the priority flowat port 3. If the input flow exceeds the priority flow requirement, the excess is bypassed out port 2. The bypass flowmay be used in a secondary circuit.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Input Flow 480 L/min.Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990019007Seal kit - Cartridge Polyurethane: 990019002Seal kit - Cartridge Viton: 990019006
(X)CONTROLX Not AdjustableL Tuning AdjustmentK Handknob
(A)SETTING RANGEA Replaceable Orifice .2 - 50 gpm (1 -
200 L/min.)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FRFA
Model Code Example: FRFAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 54 of 158
MODELFVCA
Ventable, fixed orifice, bypass/restrictive, priority, flow control valveSERIES 1 / CAPACITY: 23 L/min. / CAVITY: T-21A
Ventable, bypass/restrictive, fixed-orifice, priority flow controls take an input flow at port 1 and use it to satisfy thepriority flow at port 3. If the input flow exceeds the priority flow requirement, the excess is bypassed out port 2. Thebypass flow may be used in a secondary circuit. A vent port (port 4) allows these valves to be controlled remotely.
TECHNICAL DATAMaximum Operating Pressure 350 barNominal Vent Flow 0,75 L/min.Maximum Input Flow 60 L/min.Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990021007Seal kit - Cartridge Polyurethane: 990021002Seal kit - Cartridge Viton: 990021006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(A)SETTING RANGEA Replaceable Orifice .1 - 6 gpm (0,4 - 23
L/min.)
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FVCA
Model Code Example: FVCAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 55 of 158
MODELFVDA
Ventable, fixed orifice, bypass/restrictive, priority, flow control valveSERIES 2 / CAPACITY: 45 L/min. / CAVITY: T-22A
Ventable, bypass/restrictive, fixed-orifice, priority flow controls take an input flow at port 1 and use it to satisfy thepriority flow at port 3. If the input flow exceeds the priority flow requirement, the excess is bypassed out port 2. Thebypass flow may be used in a secondary circuit. A vent port (port 4) allows these valves to be controlled remotely.
TECHNICAL DATAMaximum Operating Pressure 350 barNominal Vent Flow 0,75 L/min.Maximum Input Flow 120 L/min.Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990022007Seal kit - Cartridge EPDM: 990022014Seal kit - Cartridge Polyurethane: 990022002Seal kit - Cartridge Viton: 990022006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(A)SETTING RANGEA Replaceable Orifice .1 - 12 gpm (0,4 -
45 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/FVDA
Model Code Example: FVDAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 56 of 158
MODELFVEA
Ventable, fixed orifice, bypass/restrictive, priority, flow control valveSERIES 3 / CAPACITY: 95 L/min. / CAVITY: T-23A
Ventable, bypass/restrictive, fixed-orifice, priority flow controls take an input flow at port 1 and use it to satisfy thepriority flow at port 3. If the input flow exceeds the priority flow requirement, the excess is bypassed out port 2. Thebypass flow may be used in a secondary circuit. A vent port (port 4) allows these valves to be controlled remotely.
TECHNICAL DATAMaximum Operating Pressure 350 barNominal Vent Flow 0,75 L/min.Maximum Input Flow 240 L/min.Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990023007Seal kit - Cartridge Polyurethane: 990023002Seal kit - Cartridge Viton: 990023006
(X)CONTROLX Not AdjustableK HandknobL Tuning Adjustment
(A)SETTING RANGEA Replaceable Orifice .2 - 25 gpm (0,8 -
95 L/min.)
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FVEA
Model Code Example: FVEAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 57 of 158
MODELFVFA
Ventable, fixed orifice, bypass/restrictive, priority, flow control valveSERIES 4 / CAPACITY: 200 L/min. / CAVITY: T-24A
Ventable, bypass/restrictive, fixed-orifice, priority flow controls take an input flow at port 1 and use it to satisfy thepriority flow at port 3. If the input flow exceeds the priority flow requirement, the excess is bypassed out port 2. Thebypass flow may be used in a secondary circuit. A vent port (port 4) allows these valves to be controlled remotely.
TECHNICAL DATAMaximum Operating Pressure 350 barNominal Vent Flow 0,75 L/min.Maximum Input Flow 480 L/min.Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990024007Seal kit - Cartridge EPDM: 990024014Seal kit - Cartridge Polyurethane: 990024002Seal kit - Cartridge Viton: 990024006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(A)SETTING RANGEA Replaceable Orifice .2 - 50 gpm (1 -
200 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/FVFA
Model Code Example: FVFAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 58 of 158
MODELFVCA8
Ventable, fixed orifice, bypass/restrictive, priority, flow control valve with integralT-8A control cavitySERIES 1 / CAPACITY: 23 L/min. / CAVITY: T-21A
This valve is a ventable, bypass/restrictive, fixed-orifice, priority flow control with an integral pilot control cavity. Thepilot control cavity will accept any T-8A pilot pressure or directional control cartridge. It takes an input flow at port 1and uses it to satisfy the priority flow at port 3. If the input flow exceeds the priority flow requirement, the excessflow is bypassed out of port 2. Bypass flow may be used for a secondary circuit. Depending on which pilot controlvalve is installed in the T-8A cavity, priority flow can be selected electrically, manually, hydraulically orpneumatically.
TECHNICAL DATAMaximum Operating Pressure 350 barNominal Vent Flow 0,75 L/min.Maximum Input Flow 60 L/min.Pilot Control Cavity T-8APilot Control Valve Installation Torque 27 - 33 NmPilot Control Valve Hex Size 22,2 mmSeal kit - Cartridge Buna: 990021007Seal kit - Cartridge Polyurethane: 990021002Seal kit - Cartridge Viton: 990021006
(A)SETTING RANGEA Replaceable Orifice .1 - 6 gpm (0,4 - 23
L/min.)B Permanent Orifice .1 - 6 gpm (0,4 - 23
L/min.)
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FVCA8
Compound cartridge (pilot and main stage) assembly information is provided for reference only. Cartridges must be ordered separately and assembled atpoint of use.NOTES
Model Code Example: FVCA8ANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 59 of 158
MODELFVDA8
Ventable, fixed orifice, bypass/restrictive, priority, flow control valve with integralT-8A control cavitySERIES 2 / CAPACITY: 45 L/min. / CAVITY: T-22A
This valve is a ventable, bypass/restrictive, fixed-orifice, priority flow control with an integral pilot control cavity. Thepilot control cavity will accept any T-8A pilot pressure or directional control cartridge. It takes an input flow at port 1and uses it to satisfy the priority flow at port 3. If the input flow exceeds the priority flow requirement, the excessflow is bypassed out of port 2. Bypass flow may be used for a secondary circuit. Depending on which pilot controlvalve is installed in the T-8A cavity, priority flow can be selected electrically, manually, hydraulically orpneumatically.
TECHNICAL DATAMaximum Operating Pressure 350 barNominal Vent Flow 0,75 L/min.Maximum Input Flow 120 L/min.Pilot Control Cavity T-8APilot Control Valve Installation Torque 27 - 33 NmPilot Control Valve Hex Size 22,2 mmSeal kit - Cartridge Buna: 990022007Seal kit - Cartridge EPDM: 990022014Seal kit - Cartridge Polyurethane: 990022002Seal kit - Cartridge Viton: 990022006
(A)SETTING RANGEA Replaceable Orifice .1 - 12 gpm (0,4 -
45 L/min.)B Permanent Orifice .1 - 12 gpm (0,4 - 45
L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/FVDA8
Compound cartridge (pilot and main stage) assembly information is provided for reference only. Cartridges must be ordered separately and assembled atpoint of use.NOTES
Model Code Example: FVDA8ANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 60 of 158
MODELFVEA8
Ventable, fixed orifice, bypass/restrictive, priority, flow control valve with integralT-8A control cavitySERIES 3 / CAPACITY: 95 L/min. / CAVITY: T-23A
This valve is a ventable, bypass/restrictive, fixed-orifice, priority flow control with an integral pilot control cavity. Thepilot control cavity will accept any T-8A pilot pressure or directional control cartridge. It takes an input flow at port 1and uses it to satisfy the priority flow at port 3. If the input flow exceeds the priority flow requirement, the excessflow is bypassed out of port 2. Bypass flow may be used for a secondary circuit. Depending on which pilot controlvalve is installed in the T-8A cavity, priority flow can be selected electrically, manually, hydraulically orpneumatically.
TECHNICAL DATAMaximum Operating Pressure 350 barNominal Vent Flow 0,75 L/min.Maximum Input Flow 240 L/min.Pilot Control Cavity T-8APilot Control Valve Installation Torque 27 - 33 NmPilot Control Valve Hex Size 22,2 mmSeal kit - Cartridge Buna: 990023007Seal kit - Cartridge Polyurethane: 990023002Seal kit - Cartridge Viton: 990023006
(A)SETTING RANGEA Replaceable Orifice .2 - 25 gpm (0,8 -
95 L/min.)B Permanent Orifice .2 - 25 gpm (0,8 - 95
L/min.)
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FVEA8
Compound cartridge (pilot and main stage) assembly information is provided for reference only. Cartridges must be ordered separately and assembled atpoint of use.NOTES
Model Code Example: FVEA8ANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 61 of 158
MODELFVFA8
Ventable, fixed orifice, bypass/restrictive, priority, flow control valve with integralT-8A control cavitySERIES 4 / CAPACITY: 200 L/min. / CAVITY: T-24A
This valve is a ventable, bypass/restrictive, fixed-orifice, priority flow control with an integral pilot control cavity. Thepilot control cavity will accept any T-8A pilot pressure or directional control cartridge. It takes an input flow at port 1and uses it to satisfy the priority flow at port 3. If the input flow exceeds the priority flow requirement, the excessflow is bypassed out of port 2. Bypass flow may be used for a secondary circuit. Depending on which pilot controlvalve is installed in the T-8A cavity, priority flow can be selected electrically, manually, hydraulically orpneumatically.
TECHNICAL DATAMaximum Operating Pressure 350 barNominal Vent Flow 0,75 L/min.Maximum Input Flow 480 L/min.Pilot Control Cavity T-8APilot Control Valve Installation Torque 27 - 33 NmPilot Control Valve Hex Size 22,2 mmSeal kit - Cartridge Buna: 990024007Seal kit - Cartridge EPDM: 990024014Seal kit - Cartridge Polyurethane: 990024002Seal kit - Cartridge Viton: 990024006
(A)SETTING RANGEA Replaceable Orifice .2 - 50 gpm (1 -
200 L/min.)B Permanent Orifice .2 - 50 gpm (1 - 200
L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/FVFA8
Compound cartridge (pilot and main stage) assembly information is provided for reference only. Cartridges must be ordered separately and assembled atpoint of use.NOTES
Model Code Example: FVFA8ANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 62 of 158
MODELFPCC
Electro-proportional flow control valve - normally closedSERIES 1 / CAPACITY: 40 L/min. / CAVITY: T-13A
This valve is a normally closed, electro-proportional throttle that is spring-biased closed. Energizing the coilgenerates an opening force on the spool proportional to the command current, and this force is countered by thespring and flow forces. This force balance creates a metering orifice whose effective size is proportional to thecurrent. The valve exhibits a large degree of self-compensation in the 1-to-2 direction and will provide proportionalflow control in the 2-to-1 direction with the addition of an external compensator. Full reverse flow (2-to-1) with 100%command in the 2-to-1 direction is possible without a compensator under all conditions.
TECHNICAL DATAMaximum Valve Leakage at 110 SUS (24 cSt) 100 cc/min.@210 barManual Override Force Requirement 33 N/100 bar @ Port 1Manual Override Stroke 2,5 mmSeal kit - Cartridge Buna: 990413007Seal kit - Cartridge EPDM: 990010014Seal kit - Cartridge Polyurethane: 990413002Seal kit - Cartridge Viton: 990413006
(X)CONTROLX No Manual OverrideD Twist/Lock (Dual) Manual OverrideE Twist (Extended) Manual OverrideL Twist/Lock (Detent) Manual OverrideM Manual OverrideT Twist (Momentary) Manual Override
(C)FLOW RATEC .25 - 7 gpm (1 - 28 L/min.)A .1 - 1.5 gpm (0,4 - 6 L/min.)B .15 - 3.5 gpm (0,6 - 14 L/min.)D .25 - 10 gpm (1 - 40 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
COIL *No coil
212 DIN 43650-Form A, 12 VDC224 DIN 43650-Form A, 24 VDC712 Twin Lead, 12 VDC724 Twin Lead, 24 VDC912 Deutsch DT04-2P, 12 VDC924 Deutsch DT04-2P, 24 VDC
* Additional coil options are available
snhy.com/FPCC
Please verify cartridge clearance requirements when choosing a Sun manifold. Different valve controls and coils require different clearances.NOTES
Model Code Example: FPCCXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 63 of 158
MODELFPCH
Electro-proportional flow control valve - normally openSERIES 1 / CAPACITY: 28 L/min. / CAVITY: T-13A
This valve is a normally open electro-proportional throttle that is spring-biased open. Energizing the coil generatesan closing force on the spool proportional to the command current, and this force is countered by the spring andflow forces. This force balance creates a metering orifice whose effective size is proportional to the current. Thevalve exhibits a large degree of self-compensation in the 1-to-2 direction and will provide proportional flow control inthe 2-to-1 direction with the addition of an external compensator. Full reverse flow (2-to-1) with no command in the2-to-1 direction is possible without a compensator under all conditions.
TECHNICAL DATAMaximum Valve Leakage at 110 SUS (24 cSt) 100 cc/min.@210 barManual Override Force Requirement 33 N/100 bar @ Port 1Manual Override Stroke 2,5 mmSeal kit - Cartridge Buna: 990413007Seal kit - Cartridge Polyurethane: 990413002Seal kit - Cartridge Viton: 990413006
(X)CONTROLX No Manual OverrideD Twist/Lock (Dual) Manual OverrideE Twist (Extended) Manual OverrideL Twist/Lock (Detent) Manual OverrideM Manual OverrideT Twist (Momentary) Manual Override
(C)FLOW RATEC .25 - 7 gpm (1 - 28 L/min.)A .1 - 1.5 gpm (0,4 - 6 L/min.)B .15 - 3.5 gpm (0,6 - 14 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
COIL *No coil
212 DIN 43650-Form A, 12 VDC224 DIN 43650-Form A, 24 VDC712 Twin Lead, 12 VDC724 Twin Lead, 24 VDC912 Deutsch DT04-2P, 12 VDC924 Deutsch DT04-2P, 24 VDC
* Additional coil options are available
snhy.com/FPCH
Please verify cartridge clearance requirements when choosing a Sun manifold. Different valve controls and coils require different clearances.NOTES
Model Code Example: FPCHXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 64 of 158
MODELFPFK
Pilot operated, normally closed, electro-proportional throttle with reverse flowcheckSERIES 2 / CAPACITY: 80 L/min. / CAVITY: T-5A
X-Control
E-Control
M-Control
This valve is a pilot-operated, normally closed, electro-proportional throttle with reverse free-flow check. Energizingthe coil generates an opening force on the pilot stage which vents the main stage poppet to open proportionally.Metered flow is from port 1 to port 2 with reverse free flow from port 2 to port 1.
TECHNICAL DATARecommended dither frequency 100 HzMaximum Valve Leakage at 110 SUS (24 cSt) 20 drops/min.@5000 psiManual Override Force Requirement 33 N/100 bar @ Port 1Deadband, nominal (as a percentage of input) 25%Manual Override Stroke 1,50 mmSeal kit - Cartridge Buna: 990203007Seal kit - Cartridge EPDM: 990203014Seal kit - Cartridge Viton: 990203006
(X)CONTROLX No Manual OverrideE Twist (Extended) Manual OverrideM Manual Override
(D)FLOW RATED Nominal 20 gpm @ 200 psi (14 bar)
differential (80 L/min.)B Nominal 10 gpm @ 200 psi (14 bar)
differential (40 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
COIL *No coil
212 DIN 43650-Form A, 12 VDC224 DIN 43650-Form A, 24 VDC712 Twin Lead, 12 VDC724 Twin Lead, 24 VDC912 Deutsch DT04-2P, 12 VDC924 Deutsch DT04-2P, 24 VDC
* Additional coil options are available
snhy.com/FPFK
Model Code Example: FPFKXDNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 65 of 158
MODELFPHK
Pilot operated, normally closed, electro-proportional throttle with reverse flowcheckSERIES 3 / CAPACITY: 240 L/min. / CAVITY: T-16A
X-Control
E-Control
M-Control
This valve is a pilot-operated, normally closed, electro-proportional throttle with reverse free-flow check. Energizingthe coil generates an opening force on the pilot stage which vents the main stage poppet to open proportionally.Metered flow is from port 1 to port 2 with reverse free flow from port 2 to port 1.
TECHNICAL DATARecommended dither frequency 100 HzMaximum Valve Leakage at 110 SUS (24 cSt) 0,7 cc/min.@350 barManual Override Force Requirement 33 N/100 bar @ Port 1Deadband, nominal (as a percentage of input) 25%Manual Override Stroke 1,50 mmSeal kit - Cartridge Buna: 990016007Seal kit - Cartridge Polyurethane: 990016002Seal kit - Cartridge Viton: 990016006
(X)CONTROLX No Manual OverrideE Twist (Extended) Manual OverrideM Manual Override
(C)FLOW RATEC Nominal 40 gpm @ 200 psi (14 bar)
differential (160 L/min.)A Nominal 20 gpm @ 200 psi (14 bar)
differential (80 L/min.)E Nominal 60 gpm @ 200 psi ( 14 bar)
differential (240 L/min.)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
COIL *No coil
212 DIN 43650-Form A, 12 VDC224 DIN 43650-Form A, 24 VDC712 Twin Lead, 12 VDC724 Twin Lead, 24 VDC912 Deutsch DT04-2P, 12 VDC924 Deutsch DT04-2P, 24 VDC
* Additional coil options are available
snhy.com/FPHK
Model Code Example: FPHKXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 66 of 158
MODELFMDA
Electro-proportional 3-way flow control valve, meter inSERIES 1 / CAPACITY: 34 L/min. / CAVITY: T-11A
X-Control D-Control
E-Control L-Control
M-Control T-Control
This valve is a 3-way, meter-in, electro-proportional throttle. The flow path, unenergized, has the supply blocked atport 1 and port 2 is drained to tank at port 3. Energizing the coil generates a closing force on the spool, creating ametering orifice in the 1 to 2 direction that is proportional to the coil command current. The valve self-compensatesin the 1-to-2 direction and with the addition of an external compensator will provide pressure compensated flowcontrol.
Flow in the 2-to-3 direction is not proportional and is limited in the interest of increased resolution and capacity.Flow capacity in the 2-to-3 direction is about 1.5 gpm (6 L/min). This valve is meant to be used in a circuit that hasa separate passage to tank such as a cushion lock circuit. Two FMDAs in conjunction with a cushion lock circuitcreate a meter-in/meter-out 3-position 4-way.
TECHNICAL DATAMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barManual Override Force Requirement 33 N/100 bar @ Port 1Manual Override Stroke 2,5 mmSeal kit - Cartridge Buna: 990411007Seal kit - Cartridge Viton: 990411006
(X)CONTROLX No Manual OverrideD Twist/Lock (Dual) Manual OverrideE Twist (Extended) Manual OverrideL Twist/Lock (Detent) Manual OverrideM Manual OverrideT Twist (Momentary) Manual Override
(D)FLOW RATED .1 - 9 gpm (0,4 - 34 L/min.)A .1 - 1.6 gpm (0,4 - 6.1 L/min.)B .1 - 4 gpm (0,4 - 15 L/min.)C .1 - 6 gpm (0,4 - 23 L/min.)
(N)SEAL MATERIALN Buna-NV Viton
COIL *No coil
212 DIN 43650-Form A, 12 VDC224 DIN 43650-Form A, 24 VDC712 Twin Lead, 12 VDC724 Twin Lead, 24 VDC912 Deutsch DT04-2P, 12 VDC924 Deutsch DT04-2P, 24 VDC
* Additional coil options are available
snhy.com/FMDA
Please verify cartridge clearance requirements when choosing a Sun manifold. Different valve controls and coils require different clearances.NOTES
Model Code Example: FMDAXDNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 67 of 158
MODELFMDB
Electro-proportional 3-way flow control valve, meter inSERIES 1 / CAPACITY: 23 L/min. / CAVITY: T-11A
This valve is a 3-way, meter-in, electro-proportional throttle. The flow path, unenergized, has the supply blocked atport 1 and port 2 connected to tank at port 3. Energizing the coil generates a closing force on the spool, creating ametering orifice in the 1 to 2 direction that is proportional to the coil command current. The valve self-compensatesin the 1 to 2 direction and with the addition of an external compensator will provide pressure compensated flowcontrol. Flow in the 2 to 3 direction is not proportional.
TECHNICAL DATAMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barManual Override Force Requirement 33 N/100 bar @ Port 1Manual Override Stroke 2,5 mmSeal kit - Cartridge Buna: 990411007Seal kit - Cartridge Viton: 990411006
(X)CONTROLX No Manual OverrideD Twist/Lock (Dual) Manual OverrideE Twist (Extended) Manual OverrideL Twist/Lock (Detent) Manual OverrideM Manual OverrideT Twist (Momentary) Manual Override
(C)FLOW RATEC .1 - 6 gpm (0,4 - 23 L/min.)A .1 - 1.6 gpm (0,4 - 6.1 L/min.)B .1 - 4 gpm (0,4 - 15 L/min.)
(N)SEAL MATERIALN Buna-NV Viton
COIL *No coil
212 DIN 43650-Form A, 12 VDC224 DIN 43650-Form A, 24 VDC712 Twin Lead, 12 VDC724 Twin Lead, 24 VDC912 Deutsch DT04-2P, 12 VDC924 Deutsch DT04-2P, 24 VDC
* Additional coil options are available
snhy.com/FMDB
Please verify cartridge clearance requirements when choosing a Sun manifold. Different valve controls and coils require different clearances.NOTES
Model Code Example: FMDBXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 68 of 158
MODELFTCA
2-way, pilot shifted, dual path, proportional throttleSERIES 2 / CAPACITY: 60 L/min. / CAVITY: T-52AD
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1opposes the spring and creates a variable metering orifice between port 2 and 3 that is proportional to the pressureat 1. The force balance of the flow forces, spring and pilot pressure results in a degree of partial self-compensationas the load pressure changes.
Pressure at port 4 directly opposes pressure at port 1.
The valve uses a dual-path design. Ports 2 and 3 incorporate a double-port area.
TECHNICAL DATAMinimum Pilot Pressure Required to Shift Valve 5,5 barPilot Pressure Required for Full Shift at Rated Flow 20 barMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barPilot Volume Displacement 0,82 ccAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Hysteresis ± 2 %Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990152007Seal kit - Cartridge Viton: 990152006
(X)CONTROLX Not AdjustableL Stroke Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FTCA
When installed in Sun's standard T-52A line mount manifold, plug unused ports and expect higher pressure drops.NOTES
Model Code Example: FTCAXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 69 of 158
MODELFTDA
2-way, pilot shifted, dual path, proportional throttleSERIES 2 / CAPACITY: 120 L/min. / CAVITY: T-52AD
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1opposes the spring and creates a variable metering orifice between port 2 and 3 that is proportional to the pressureat 1. The force balance of the flow forces, spring and pilot pressure results in a degree of partial self-compensationas the load pressure changes.
Pressure at port 4 directly opposes pressure at port 1.
The valve uses a dual-path design. Ports 2 and 3 incorporate a double-port area.
TECHNICAL DATAMinimum Pilot Pressure Required to Shift Valve 5,5 barPilot Pressure Required for Full Shift at Rated Flow 20 barMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barPilot Volume Displacement 0,82 ccHysteresis ± 2 %Seal kit - Cartridge Buna: 990152007Seal kit - Cartridge Viton: 990152006
(X)CONTROLX Not AdjustableL Stroke Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FTDA
When installed in Sun's standard T-52A line mount manifold, plug unused ports and expect higher pressure drops.NOTES
Model Code Example: FTDAXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 70 of 158
MODELFTEA
2-way, pilot shifted, dual path, proportional throttleSERIES 3 / CAPACITY: 95 L/min. / CAVITY: T-53AD
This valve is a 2-way, 2-position proportional throttle. Pilot pressure at port 1 opposes the spring and creates avariable metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of the flowforces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
Pressure at port 4 directly opposes pressure at port 1.
The valve uses a dual-path design. Ports 2 and 3 incorporate a double-port area.
TECHNICAL DATAMinimum Pilot Pressure Required to Shift Valve 5,5 barPilot Pressure Required for Full Shift at Rated Flow 24 barMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 160 cc/min.@70 barPilot Volume Displacement 1,6 ccAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Hysteresis ± 2 %Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990053007Seal kit - Cartridge Viton: 990053006
(X)CONTROLX Not AdjustableL Stroke Adjustment
(C)SPOOL CONFIGURATIONC Normally ClosedH Normally Open
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FTEA
When installed in Sun's standard T-53A line mount manifold, plug unused ports and expect higher pressure drops.NOTES
Model Code Example: FTEAXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 71 of 158
MODELFTFA
2-way, pilot shifted, dual path, proportional throttleSERIES 3 / CAPACITY: 200 L/min. / CAVITY: T-53AD
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1opposes the spring and creates a variable metering orifice between port 2 and 3 that is proportional to the pressureat 1. The force balance of the flow forces, spring and pilot pressure results in a degree of partial self-compensationas the load pressure changes.
Pressure at port 4 directly opposes pressure at port 1.
The valve uses a dual-path design. Ports 2 and 3 incorporate a double-port area.
TECHNICAL DATAMinimum Pilot Pressure Required to Shift Valve 4 barPilot Pressure Required for Full Shift at Rated Flow 20 barMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 190 cc/min.@70 barPilot Volume Displacement 1,9 ccAdjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open 5Hysteresis ± 2 %Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990053007Seal kit - Cartridge Viton: 990053009
(X)CONTROLX Not AdjustableL Stroke Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FTFA
When installed in Sun's standard T-53A line mount manifold, plug unused ports and expect higher pressure drops.NOTES
Model Code Example: FTFAXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 72 of 158
MODELFTCAZ
2-way, pilot shifted, dual path, proportional throttle with position switchSERIES 2 / CAPACITY: 60 L/min. / CAVITY: T-52AD
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The metering passage isself-compensating.
This valve uses a dual-path design. Ports 2 and 3 incorporate a double-port area.
This valve incorporates a position switch to provide confirmation that the valve is closed.
TECHNICAL DATAMinimum Pilot Pressure Required to Shift Valve 3,5 barPilot Pressure Required for Full Shift at Rated Flow 20 barMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barPilot Volume Displacement 0,82 ccSeal kit - Cartridge Buna: 990152007Seal kit - Cartridge Viton: 990152006
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FTCAZ
When installed in Sun's standard T-52A line mount manifold, plug unused ports and expect higher pressure drops.NOTES
Model Code Example: FTCAZCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 73 of 158
MODELFTDAZ
2-way, pilot shifted, dual path, proportional throttle with position switchSERIES 2 / CAPACITY: 120 L/min. / CAVITY: T-52AD
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The metering passage isself-compensating.
This valve uses a dual-path design. Ports 2 and 3 incorporate a double-port area.
This valve incorporates a position switch to provide confirmation that the valve is closed.
TECHNICAL DATAPilot Pressure Required for Full Shift at Rated Flow 20 barMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barPilot Volume Displacement 0,82 ccSeal kit - Cartridge Buna: 990152007Seal kit - Cartridge Viton: 990152006
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FTDAZ
When installed in Sun's standard T-52A line mount manifold, plug unused ports and expect higher pressure drops.NOTES
Model Code Example: FTDAZCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 74 of 158
MODELFTEAZ
2-way, pilot shifted, dual path, proportional throttle with position switchSERIES 3 / CAPACITY: 95 L/min. / CAVITY: T-53AD
This valve is a 2-way, 2-position proportional throttle. Pilot pressure at port 1 creates a metering orifice between port2 and 3 that is proportional to the pressure at 1. The metering passage is self-compensating.
This valve uses a dual-path design, Ports 2 and 3 incorporate a double-port area.
This valve incorporates a position switch to provide position confirmation.
TECHNICAL DATAMinimum Pilot Pressure Required to Shift Valve 5,5 barPilot Pressure Required for Full Shift at Rated Flow 24 barMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 160 cc/min.@70 barPilot Volume Displacement 1,6 ccSeal kit - Cartridge Buna: 990053007Seal kit - Cartridge Viton: 990053006
(C)SPOOL CONFIGURATIONC Normally ClosedH Normally Open
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FTEAZ
When installed in Sun's standard T-53A line mount manifold, plug unused ports and expect higher pressure drops.NOTES
Model Code Example: FTEAZCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 75 of 158
MODELFTFAZ
2-way, pilot shifted, dual path, proportional throttle with position switchSERIES 3 / CAPACITY: 200 L/min. / CAVITY: T-53AD
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The metering passage isself-compensating.
This valve uses a dual-path design. Ports 2 and 3 incorporate a double-port area.
This valve incorporates a position switch to provide confirmation that the valve is closed.
TECHNICAL DATAMinimum Pilot Pressure Required to Shift Valve 4 barPilot Pressure Required for Full Shift at Rated Flow 20 barMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 160 cc/min.@70 barPilot Volume Displacement 1,6 ccSeal kit - Cartridge Buna: 990053007Seal kit - Cartridge Viton: 990053006
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FTFAZ
When installed in Sun's standard T-53A line mount manifold, plug unused ports and expect higher pressure drops.NOTES
Model Code Example: FTFAZCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 76 of 158
MODELFKBA
2-way, pilot shifted, proportional throttleSERIES 1 / CAPACITY: 20 L/min. / CAVITY: T-21A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barPilot Volume Displacement 0,33 ccMinimum Pilot Pressure to Operate 7 barHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990021007Seal kit - Cartridge EPDM: 990021014Seal kit - Cartridge Polyurethane: 990021002Seal kit - Cartridge Viton: 990021006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/FKBA
Model Code Example: FKBAXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 77 of 158
MODELFKCA
2-way, pilot shifted, proportional throttle, high capacitySERIES 1 / CAPACITY: 34 L/min. / CAVITY: T-21A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barPilot Volume Displacement 0,33 ccMinimum Pilot Pressure to Operate 7 barHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990021007Seal kit - Cartridge Polyurethane: 990021002Seal kit - Cartridge Viton: 990021006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FKCA
Model Code Example: FKCAXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 78 of 158
MODELFKDA
2-way, pilot shifted, proportional throttleSERIES 2 / CAPACITY: 40 L/min. / CAVITY: T-22A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barPilot Volume Displacement .03 in³Minimum Pilot Pressure to Operate 7 barHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990022002Seal kit - Cartridge Polyurethane: 990022002Seal kit - Cartridge Viton: 990022006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FKDA
Model Code Example: FKDAXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 79 of 158
MODELFKEA
2-way, pilot shifted, proportional throttle, high capacitySERIES 2 / CAPACITY: 80 L/min. / CAVITY: T-22A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barPilot Volume Displacement 4,9 ccMinimum Pilot Pressure to Operate 7 barHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990022002Seal kit - Cartridge Polyurethane: 990022002Seal kit - Cartridge Viton: 990022006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FKEA
Model Code Example: FKEAXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 80 of 158
MODELFKFA
2-way, pilot shifted, proportional throttleSERIES 3 / CAPACITY: 80 L/min. / CAVITY: T-23A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 65 cc/min.@70 barPilot Volume Displacement 1,6 ccMinimum Pilot Pressure to Operate 7 barHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990023007Seal kit - Cartridge Polyurethane: 990023002Seal kit - Cartridge Viton: 990023006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FKFA
Model Code Example: FKFAXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 81 of 158
MODELFKGA
2-way, pilot shifted, proportional throttle, high capacitySERIES 3 / CAPACITY: 120 L/min. / CAVITY: T-23A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 95 cc/min.@70 barPilot Volume Displacement 1,9 ccMinimum Pilot Pressure to Operate 7 barHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990023007Seal kit - Cartridge EPDM: 990023014Seal kit - Cartridge Polyurethane: 990023002Seal kit - Cartridge Viton: 990023009
(X)CONTROLX Not AdjustableL Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/FKGA
Model Code Example: FKGAXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 82 of 158
MODELFKHA
2-way, pilot shifted, proportional throttleSERIES 4 / CAPACITY: 160 L/min. / CAVITY: T-24A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) �8 cc/min.@70 barPilot Volume Displacement 3,3 ccMinimum Pilot Pressure to Operate 7 barHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990024007Seal kit - Cartridge Polyurethane: 990024002Seal kit - Cartridge Viton: 990024006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FKHA
Model Code Example: FKHAXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 83 of 158
MODELFKIA
2-way, pilot shifted, proportional throttle, high capacitySERIES 4 / CAPACITY: 240 L/min. / CAVITY: T-24A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) ✁8 cc/min.@70 barPilot Volume Displacement 3,3 ccMinimum Pilot Pressure to Operate 7 barHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque ✁ - 10 NmSeal kit - Cartridge Buna: ✁✁0024007Seal kit - Cartridge Polyurethane: ✁✁0024002Seal kit - Cartridge Viton: ✁✁0024006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FKIA
Model Code Example: FKIAXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 84 of 158
MODELFKBB
2-way, pilot shifted, proportional throttle with bleed downSERIES 1 / CAPACITY: 20 L/min. / CAVITY: T-21A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
This valve includes a bleed-down feature which connects ports 3 to 4 in the spring-biased position. The bleed-downfeature is useful when the valve is used as a meter-in flow control in circuits which include counterbalance valvesdownstream of port 3. The bleed-down connection is closed as the valve is piloted with increasing pressure at port1.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barPilot Volume Displacement 0,33 ccMinimum Pilot Pressure to Operate 7 barBypass orifice 0,8 mmHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990021007Seal kit - Cartridge Polyurethane: 990021002Seal kit - Cartridge Viton: 990021006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FKBB
Model Code Example: FKBBXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 85 of 158
MODELFKCB
2-way, pilot shifted, proportional throttle with bleed down, high capacitySERIES 1 / CAPACITY: 34 L/min. / CAVITY: T-21A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
This valve includes a bleed-down feature which connects ports 3 to 4 in the spring-biased position. The bleed-downfeature is useful when the valve is used as a meter-in flow control in circuits which include counterbalance valvesdownstream of port 3. The bleed-down connection is closed as the valve is piloted with increasing pressure at port1.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barPilot Volume Displacement 0,33 ccMinimum Pilot Pressure to Operate 7 barBypass orifice 0,8 mmHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990021007Seal kit - Cartridge Polyurethane: 990021002Seal kit - Cartridge Viton: 990021006
(X)CONTROLX Not AdjustableL Standard Screw Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FKCB
Model Code Example: FKCBXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 86 of 158
MODELFKDB
2-way, pilot shifted, proportional throttle with bleed downSERIES 2 / CAPACITY: 40 L/min. / CAVITY: T-22A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
This valve includes a bleed-down feature which connects ports 3 to 4 in the spring-biased position. The bleed-downfeature is useful when the valve is used as a meter-in flow control in circuits which include counterbalance valvesdownstream of port 3. The bleed-down connection is closed as the valve is piloted with increasing pressure at port1.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barPilot Volume Displacement 4,✂ ccMinimum Pilot Pressure to Operate 7 barBypass orifice 0,8 mmHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990022002Seal kit - Cartridge Polyurethane: 990022002Seal kit - Cartridge Viton: 990022006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FKDB
Model Code Example: FKDBXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 87 of 158
MODELFKEB
2-way, pilot shifted, proportional throttle with bleed down, high capacitySERIES 2 / CAPACITY: 80 L/min. / CAVITY: T-22A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
This valve includes a bleed-down feature which connects ports 3 to 4 in the spring-biased position. The bleed-downfeature is useful when the valve is used as a meter-in flow control in circuits which include counterbalance valvesdownstream of port 3. The bleed-down connection is closed as the valve is piloted with increasing pressure at port1.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barPilot Volume Displacement 4,9 ccMinimum Pilot Pressure to Operate 7 barBypass orifice 0,8 mmHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990022002Seal kit - Cartridge Polyurethane: 990022002Seal kit - Cartridge Viton: 990022006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FKEB
Model Code Example: FKEBXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 88 of 158
MODELFKFB
2-way, pilot shifted, proportional throttle with bleed downSERIES 3 / CAPACITY: 80 L/min. / CAVITY: T-23A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
This valve includes a bleed-down feature which connects ports 3 to 4 in the spring-biased position. The bleed-downfeature is useful when the valve is used as a meter-in flow control in circuits which include counterbalance valvesdownstream of port 3. The bleed-down connection is closed as the valve is piloted with increasing pressure at port1.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 95 cc/min.@70 barPilot Volume Displacement 1,9 ccMinimum Pilot Pressure to Operate 7 barBypass orifice 0,8 mmHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990023007Seal kit - Cartridge EPDM: 990023014Seal kit - Cartridge Polyurethane: 990023002Seal kit - Cartridge Viton: 990023006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/FKFB
Model Code Example: FKFBXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 89 of 158
MODELFKGB
2-way, pilot shifted, proportional throttle with bleed down, high capacitySERIES 3 / CAPACITY: 120 L/min. / CAVITY: T-23A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
This valve includes a bleed-down feature which connects ports 3 to 4 in the spring-biased position. The bleed-downfeature is useful when the valve is used as a meter-in flow control in circuits which include counterbalance valvesdownstream of port 3. The bleed-down connection is closed as the valve is piloted with increasing pressure at port1.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) 65 cc/min.@70 barPilot Volume Displacement 1,6 ccMinimum Pilot Pressure to Operate 7 barBypass orifice 0,8 mmHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990023007Seal kit - Cartridge Polyurethane: 990023002Seal kit - Cartridge Viton: 990023006
(X)CONTROLX Not Adjustable
L Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-N
V Viton
snhy.com/FKGB
Model Code Example: FKGBXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 90 of 158
MODELFKHB
2-way, pilot shifted, proportional throttle with bleed downSERIES 4 / CAPACITY: 160 L/min. / CAVITY: T-24A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
This valve includes a bleed-down feature which connects ports 3 to 4 in the spring-biased position. The bleed-downfeature is useful when the valve is used as a meter-in flow control in circuits which include counterbalance valvesdownstream of port 3. The bleed-down connection is closed as the valve is piloted with increasing pressure at port1.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) ✄8 cc/min.@70 barPilot Volume Displacement 3,3 ccMinimum Pilot Pressure to Operate 7 barBypass orifice 0,8 mmHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque ✄ - 10 NmSeal kit - Cartridge Buna: ✄✄0024007Seal kit - Cartridge EPDM: ✄✄0024014Seal kit - Cartridge Polyurethane: ✄✄0024002Seal kit - Cartridge Viton: ✄✄0024006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/FKHB
Model Code Example: FKHBXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 91 of 158
MODELFKIB
2-way, pilot shifted, proportional throttle with bleed down, high capacitySERIES 4 / CAPACITY: 240 L/min. / CAVITY: T-24A
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The force balance of theflow forces, spring and pilot pressure results in a degree of partial self-compensation as the load pressure changes.
This valve includes a bleed-down feature which connects ports 3 to 4 in the spring-biased position. The bleed-downfeature is useful when the valve is used as a meter-in flow control in circuits which include counterbalance valvesdownstream of port 3. The bleed-down connection is closed as the valve is piloted with increasing pressure at port1.
Pressure at port 4 directly opposes pressure at port 1.
TECHNICAL DATAMaximum Operating Pressure 350 barMaximum Valve Leakage at 110 SUS (24 cSt) ☎8 cc/min.@70 barPilot Volume Displacement 3,3 ccMinimum Pilot Pressure to Operate 7 barBypass orifice 0,8 mmHysteresis ± 2 %Adjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque ☎ - 10 NmSeal kit - Cartridge Buna: ☎☎0024007Seal kit - Cartridge Polyurethane: ☎☎0024002Seal kit - Cartridge Viton: ☎☎0024006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(C)SPOOL CONFIGURATIONC Normally Closed
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FKIB
Model Code Example: FKIBXCNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 92 of 158
MODELFSCD
Flow divider valveSERIES 1 / CAPACITY: 6 - 30 L/min. / CAVITY: T-31A
Flow dividers are sliding-spool, pressure-compensated devices used to split oil flow to two different branches of acircuit in a designated ratio. These valves are suitable for applications that use the following: unidirectionalhydraulic motors, hydraulic cylinders where flow division in one direction only is required, and multiple circuits thatare serviced from one pump supply.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow ±6.5%Divisional Accuracy at Max Input Flow ±3.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 18 barRated Input Flow with 50/50 Split 6 - 30 L/min.Rated Input Flow with 40/60 Split 5,3 - 26,5 L/min.Rated Input Flow with 33/67 Split 4,5 - 22,7 L/min.Seal kit - Cartridge Buna: 990031007Seal kit - Cartridge Polyurethane: 990031002Seal kit - Cartridge Viton: 990031006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50B 40/60C 33/67
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FSCD
Model Code Example: FSCDXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 93 of 158
MODELFSDD
Flow divider valveSERIES 2 / CAPACITY: 12 - 60 L/min. / CAVITY: T-32A
Flow dividers are sliding-spool, pressure-compensated devices used to split oil flow to two different branches of acircuit in a designated ratio. These valves are suitable for applications that use the following: unidirectionalhydraulic motors, hydraulic cylinders where flow division in one direction only is required, and multiple circuits thatare serviced from one pump supply.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow ±6.5%Divisional Accuracy at Max Input Flow ±3.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 18 barRated Input Flow with 50/50 Split 12 - 60 L/min.Rated Input Flow with 40/60 Split 9,4 - 47 L/min.Rated Input Flow with 33/67 Split 8,4 - 42 L/min.Seal kit - Cartridge Buna: 990032007Seal kit - Cartridge Polyurethane: 990032002Seal kit - Cartridge Viton: 990032006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50B 40/60C 33/67
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FSDD
Model Code Example: FSDDXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 94 of 158
MODELFSED
Flow divider valveSERIES 3 / CAPACITY: 23 - 120 L/min. / CAVITY: T-33A
Flow dividers are sliding-spool, pressure-compensated devices used to split oil flow to two different branches of acircuit in a designated ratio. These valves are suitable for applications that use the following: unidirectionalhydraulic motors, hydraulic cylinders where flow division in one direction only is required, and multiple circuits thatare serviced from one pump supply.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow ±6.5%Divisional Accuracy at Max Input Flow ±3.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 18 barRated Input Flow with 50/50 Split 23 - 120 L/min.Rated Input Flow with 40/60 Split 19 - 95 L/min.Rated Input Flow with 33/67 Split 17 - 85 L/min.Seal kit - Cartridge Buna: 990033007Seal kit - Cartridge Polyurethane: 990033002Seal kit - Cartridge Viton: 990033006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50B 40/60C 33/67
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FSED
Model Code Example: FSEDXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 95 of 158
MODELFSFD
Flow divider valveSERIES 4 / CAPACITY: 45 - 240 L/min. / CAVITY: T-34A
Flow dividers are sliding-spool, pressure-compensated devices used to split oil flow to two different branches of acircuit in a designated ratio. These valves are suitable for applications that use the following: unidirectionalhydraulic motors, hydraulic cylinders where flow division in one direction only is required, and multiple circuits thatare serviced from one pump supply.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow ±6.5%Divisional Accuracy at Max Input Flow ±3.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 18 barRated Input Flow with 50/50 Split 45 - 240 L/min.Rated Input Flow with 40/60 Split 38 - 200 L/min.Rated Input Flow with 33/67 Split 36 - 180 L/min.Seal kit - Cartridge Buna: 990034007Seal kit - Cartridge Polyurethane: 990034002Seal kit - Cartridge Viton: 990034006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50B 40/60C 33/67D 25/75
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/LH Mild Steel, Zinc-Nickel
snhy.com/FSFD
Model Code Example: FSFDXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 96 of 158
MODELFSBD
High accuracy flow divider valveSERIES 1 / CAPACITY: 2,5 - 12 L/min. / CAVITY: T-31A
Flow dividers are sliding-spool, pressure-compensated devices used to split oil flow to two different branches of acircuit in a designated ratio. These valves are suitable for applications that use the following: unidirectionalhydraulic motors, hydraulic cylinders where flow division in one direction only is required, and multiple circuits thatare serviced from one pump supply.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow ±4.5%Divisional Accuracy at Max Input Flow ±2.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 18 barRated Input Flow with 50/50 Split 2,5 - 12 L/min.Rated Input Flow with 40/60 Split 2,8 - 9,5 L/min.Rated Input Flow with 33/67 Split 1,7 - 8,5 L/min.Seal kit - Cartridge Buna: 990031007Seal kit - Cartridge Polyurethane: 990031002Seal kit - Cartridge Viton: 990031006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50B 40/60C 33/67
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FSBD
Model Code Example: FSBDXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 97 of 158
MODELFSDC
High accuracy flow divider valveSERIES 2 / CAPACITY: 6 - 30 L/min. / CAVITY: T-32A
Flow dividers are sliding-spool, pressure-compensated devices used to split oil flow to two different branches of acircuit in a designated ratio. These valves are suitable for applications that use the following: unidirectionalhydraulic motors, hydraulic cylinders where flow division in one direction only is required, and multiple circuits thatare serviced from one pump supply.
TECHNICAL DATAPressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 18 barSeal kit - Cartridge Buna: 990032007Seal kit - Cartridge Polyurethane: 990032002Seal kit - Cartridge Viton: 990032006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FSDC
Model Code Example: FSDCXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 98 of 158
MODELFSEC
High accuracy flow divider valveSERIES 3 / CAPACITY: 12 - 60 L/min. / CAVITY: T-33A
Flow dividers are sliding-spool, pressure-compensated devices used to split oil flow to two different branches of acircuit in a designated ratio. These valves are suitable for applications that use the following: unidirectionalhydraulic motors, hydraulic cylinders where flow division in one direction only is required, and multiple circuits thatare serviced from one pump supply.
TECHNICAL DATAPressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 18 barSeal kit - Cartridge Buna: 990033007Seal kit - Cartridge Polyurethane: 990033002Seal kit - Cartridge Viton: 990033006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FSEC
Model Code Example: FSECXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 99 of 158
MODELFSFC
High accuracy flow divider valveSERIES 4 / CAPACITY: 23 - 120 L/min. / CAVITY: T-34A
Flow dividers are sliding-spool, pressure-compensated devices used to split oil flow to two different branches of acircuit in a designated ratio. These valves are suitable for applications that use the following: unidirectionalhydraulic motors, hydraulic cylinders where flow division in one direction only is required, and multiple circuits thatare serviced from one pump supply.
TECHNICAL DATAPressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 18 barSeal kit - Cartridge Buna: 990034007Seal kit - Cartridge Polyurethane: 990034002Seal kit - Cartridge Viton: 990034006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FSFC
Model Code Example: FSFCXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 100 of 158
MODELFSCA
Closed center, flow divider-combiner valveSERIES 1 / CAPACITY: 6 - 30 L/min. / CAVITY: T-31A
Closed-center flow divider/combiners are sliding-spool, pressure-compensated devices used to split flow in onedirection and combine flow in the opposite direction. These valves may be used to accurately control two or morecylinders or hydraulic motors where bidirectional operation is required.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±4.5%Divisional Accuracy at Max Input Flow 50% ±2.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990031007Seal kit - Cartridge Polyurethane: 990031002Seal kit - Cartridge Viton: 990031006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FSCA
Model Code Example: FSCAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 101 of 158
MODELFSDA
Closed center, flow divider-combiner valveSERIES 2 / CAPACITY: 12 - 60 L/min. / CAVITY: T-32A
Closed-center flow divider/combiners are sliding-spool, pressure-compensated devices used to split flow in onedirection and combine flow in the opposite direction. These valves may be used to accurately control two or morecylinders or hydraulic motors where bidirectional operation is required.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±4.5%Divisional Accuracy at Max Input Flow 50% ±2.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990032007Seal kit - Cartridge EPDM: 990032014Seal kit - Cartridge Polyurethane: 990032002Seal kit - Cartridge Viton: 990032006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FSDA
Model Code Example: FSDAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 102 of 158
MODELFSEA
Closed center, flow divider-combiner valveSERIES 3 / CAPACITY: 23 - 120 L/min. / CAVITY: T-33A
Closed-center flow divider/combiners are sliding-spool, pressure-compensated devices used to split flow in onedirection and combine flow in the opposite direction. These valves may be used to accurately control two or morecylinders or hydraulic motors where bidirectional operation is required.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±4.5%Divisional Accuracy at Max Input Flow 50% ±2.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990033007Seal kit - Cartridge Polyurethane: 990033002Seal kit - Cartridge Viton: 990033006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FSEA
Model Code Example: FSEAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 103 of 158
MODELFSFA
Closed center, flow divider-combiner valveSERIES 4 / CAPACITY: 45 - 240 L/min. / CAVITY: T-34A
Closed-center flow divider/combiners are sliding-spool, pressure-compensated devices used to split flow in onedirection and combine flow in the opposite direction. These valves may be used to accurately control two or morecylinders or hydraulic motors where bidirectional operation is required.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±4.5%Divisional Accuracy at Max Input Flow 50% ±2.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990034007Seal kit - Cartridge Polyurethane: 990034002Seal kit - Cartridge Viton: 990034006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
snhy.com/FSFA
Model Code Example: FSFAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 104 of 158
MODELFSAA
High accuracy, closed center, flow divider-combiner valveSERIES 1 / CAPACITY: 1 - 6 L/min. / CAVITY: T-31A
High accuracy, closed-center flow divider/combiners are sliding-spool, pressure-compensated devices used to splitflow in one direction and combine flow in the opposite direction. These valves may be used to accurately controltwo or more cylinders or hydraulic motors where bidirectional operation is required.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±3.5%Divisional Accuracy at Max Input Flow 50% ±2.0%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990031007Seal kit - Cartridge Polyurethane: 990031002Seal kit - Cartridge Viton: 990031006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FSAA
Model Code Example: FSAAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 105 of 158
MODELFSBA
High accuracy, closed center, flow divider-combiner valveSERIES 1 / CAPACITY: 2,5 - 12 L/min. / CAVITY: T-31A
Closed-center flow divider/combiners are sliding-spool, pressure-compensated devices used to split flow in onedirection and combine flow in the opposite direction. These valves may be used to accurately control two or morecylinders or hydraulic motors where bidirectional operation is required.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±3.0%Divisional Accuracy at Max Input Flow 50% ±2.0%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990031007Seal kit - Cartridge Polyurethane: 990031002Seal kit - Cartridge Viton: 990031006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FSBA
Model Code Example: FSBAXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 106 of 158
MODELFSDG
High accuracy, closed center, flow divider-combiner valveSERIES 2 / CAPACITY: 6 - 30 L/min. / CAVITY: T-32A
High accuracy, closed-center flow divider/combiners are sliding-spool, pressure-compensated devices used to splitflow in one direction and combine flow in the opposite direction. These valves may be used to accurately controltwo or more cylinders or hydraulic motors where bidirectional operation is required.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±2.5%Divisional Accuracy at Max Input Flow 50% ±1.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990032007Seal kit - Cartridge Polyurethane: 990032002Seal kit - Cartridge Viton: 990032006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/LH Mild Steel, Zinc-Nickel
snhy.com/FSDG
Model Code Example: FSDGXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 107 of 158
MODELFSEG
High accuracy, closed center, flow divider-combiner valveSERIES 3 / CAPACITY: 12 - 60 L/min. / CAVITY: T-33A
High accuracy, closed-center flow divider/combiners are sliding-spool, pressure-compensated devices used to splitflow in one direction and combine flow in the opposite direction. These valves may be used to accurately controltwo or more cylinders or hydraulic motors where bidirectional operation is required.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±2.5%Divisional Accuracy at Max Input Flow 50% ±1.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990033007Seal kit - Cartridge Polyurethane: 990033002Seal kit - Cartridge Viton: 990033006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FSEG
Model Code Example: FSEGXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 108 of 158
MODELFSFG
High accuracy, closed center, flow divider-combiner valveSERIES 4 / CAPACITY: 23 - 120 L/min. / CAVITY: T-34A
High accuracy, closed-center flow divider/combiners are sliding-spool, pressure-compensated devices used to splitflow in one direction and combine flow in the opposite direction. These valves may be used to accurately controltwo or more cylinders or hydraulic motors where bidirectional operation is required.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±2.5%Divisional Accuracy at Max Input Flow 50% ±1.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990034007Seal kit - Cartridge Polyurethane: 990034002Seal kit - Cartridge Viton: 990034006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FSFG
Model Code Example: FSFGXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 109 of 158
MODELFSCH
High capacity, closed center, flow divider-combiner valveSERIES 1 / CAPACITY: 8 - 34 L/min. / CAVITY: T-31A
High-capacity, closed-center flow divider/combiners are sliding-spool, pressure-compensated devices used to splitflow in one direction and combine flow in the opposite direction. These valves have approximate 15% greatercapacity than standard closed-center divider/combiners and are designed for use in tractive drive systems. Note:Accuracy on these cartridges is not equivalent to the accuracy of standard closed-center divider/combiners.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±6.5%Divisional Accuracy at Max Input Flow 50% ±3.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990031007Seal kit - Cartridge Polyurethane: 990031002Seal kit - Cartridge Viton: 990031006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FSCH
Model Code Example: FSCHXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 110 of 158
MODELFSDH
High capacity, closed center, flow divider-combiner valveSERIES 2 / CAPACITY: 15 - 65 L/min. / CAVITY: T-32A
High-capacity, closed-center flow divider/combiners are sliding-spool, pressure-compensated devices used to splitflow in one direction and combine flow in the opposite direction. These valves have approximate 15% greatercapacity than standard closed-center divider/combiners and are designed for use in tractive drive systems. Note:Accuracy on these cartridges is not equivalent to the accuracy of standard closed-center divider/combiners.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±6.5%Divisional Accuracy at Max Input Flow 50% ±3.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990032007Seal kit - Cartridge Polyurethane: 990032002Seal kit - Cartridge Viton: 990032006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FSDH
Model Code Example: FSDHXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 111 of 158
MODELFSEH
High capacity, closed center, flow divider-combiner valveSERIES 3 / CAPACITY: 32 - 130 L/min. / CAVITY: T-33A
High-capacity, closed-center flow divider/combiners are sliding-spool, pressure-compensated devices used to splitflow in one direction and combine flow in the opposite direction. These valves have approximate 15% greatercapacity than standard closed-center divider/combiners and are designed for use in tractive drive systems. Note:Accuracy on these cartridges is not equivalent to the accuracy of standard closed-center divider/combiners.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±6.5%Divisional Accuracy at Max Input Flow 50% ±3.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990033007Seal kit - Cartridge Polyurethane: 990033002Seal kit - Cartridge Viton: 990033006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FSEH
Model Code Example: FSEHXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 112 of 158
MODELFSFH
High capacity, closed center, flow divider-combiner valveSERIES 4 / CAPACITY: 60 - 270 L/min. / CAVITY: T-34A
High-capacity, closed-center flow divider/combiners are sliding-spool, pressure-compensated devices used to splitflow in one direction and combine flow in the opposite direction. These valves have approximate 15% greatercapacity than standard closed-center divider/combiners and are designed for use in tractive drive systems. Note:Accuracy on these cartridges is not equivalent to the accuracy of standard closed-center divider/combiners.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±6.5%Divisional Accuracy at Max Input Flow 50% ±3.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990034007Seal kit - Cartridge Polyurethane: 990034002Seal kit - Cartridge Viton: 990034006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/LH Mild Steel, Zinc-Nickel
snhy.com/FSFH
Model Code Example: FSFHXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 113 of 158
MODELFSCS
Synchronizing, flow divider-combiner valveSERIES 1 / CAPACITY: 6 - 30 L/min. / CAVITY: T-31A
Synchronizing flow divider/combiners are sliding-spool, pressure-compensated devices used to split flow in onedirection and combine flow in the opposite direction. With a sychronizing feature, these valves can be used to allowtwo hydraulic cylinders to fully stroke and synchronize at the end of the stroke. When the first cylinder has reachedthe end of its stroke, a pressure-compensated, reduced flow is metered to or from the second cylinder until it alsoreaches the end of its stroke.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±4.5%Divisional Accuracy at Max Input Flow 50% ±2.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990031007Seal kit - Cartridge Polyurethane: 990031002Seal kit - Cartridge Viton: 990031006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FSCS
Model Code Example: FSCSXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 114 of 158
MODELFSDS
Synchronizing, flow divider-combiner valveSERIES 2 / CAPACITY: 12 - 60 L/min. / CAVITY: T-32A
Synchronizing flow divider/combiners are sliding-spool, pressure-compensated devices used to split flow in onedirection and combine flow in the opposite direction. With a sychronizing feature, these valves can be used to allowtwo hydraulic cylinders to fully stroke and synchronize at the end of the stroke. When the first cylinder has reachedthe end of its stroke, a pressure-compensated, reduced flow is metered to or from the second cylinder until it alsoreaches the end of its stroke.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±4.5%Divisional Accuracy at Max Input Flow 50% ±2.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990032007Seal kit - Cartridge Polyurethane: 990032002Seal kit - Cartridge Viton: 990032006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FSDS
Model Code Example: FSDSXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 115 of 158
MODELFSES
Synchronizing, flow divider-combiner valveSERIES 3 / CAPACITY: 23 - 120 L/min. / CAVITY: T-33A
Synchronizing flow divider/combiners are sliding-spool, pressure-compensated devices used to split flow in onedirection and combine flow in the opposite direction. With a sychronizing feature, these valves can be used to allowtwo hydraulic cylinders to fully stroke and synchronize at the end of the stroke. When the first cylinder has reachedthe end of its stroke, a pressure-compensated, reduced flow is metered to or from the second cylinder until it alsoreaches the end of its stroke.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±4.5%Divisional Accuracy at Max Input Flow 50% ±2.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990033007Seal kit - Cartridge Polyurethane: 990033002Seal kit - Cartridge Viton: 990033006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FSES
Model Code Example: FSESXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 116 of 158
MODELFSFS
Synchronizing, flow divider-combiner valveSERIES 4 / CAPACITY: 45 - 240 L/min. / CAVITY: T-34A
Synchronizing flow divider/combiners are sliding-spool, pressure-compensated devices used to split flow in onedirection and combine flow in the opposite direction. With a sychronizing feature, these valves can be used to allowtwo hydraulic cylinders to fully stroke and synchronize at the end of the stroke. When the first cylinder has reachedthe end of its stroke, a pressure-compensated, reduced flow is metered to or from the second cylinder until it alsoreaches the end of its stroke.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±4.5%Divisional Accuracy at Max Input Flow 50% ±2.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990034007Seal kit - Cartridge Polyurethane: 990034002Seal kit - Cartridge Viton: 990034006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/FSFS
Model Code Example: FSFSXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 117 of 158
MODELFSAS
High accuracy synchronizing, flow divider-combiner valveSERIES 1 / CAPACITY: 1 - 6 L/min. / CAVITY: T-31A
High accuracy, synchronizing flow divider/combiners are sliding-spool, pressure-compensated devices used to splitflow in one direction and combine flow in the opposite direction. With a sychronizing feature, these valves can beused to allow two hydraulic cylinders to fully stroke and synchronize at the end of the stroke. When the firstcylinder has reached the end of its stroke, a pressure-compensated, reduced flow is metered to or from the secondcylinder until it also reaches the end of its stroke.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±3.5%Divisional Accuracy at Max Input Flow 50% ±2.0%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990031007Seal kit - Cartridge Polyurethane: 990031002Seal kit - Cartridge Viton: 990031006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FSAS
Model Code Example: FSASXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 118 of 158
MODELFSBS
High accuracy synchronizing, flow divider-combiner valveSERIES 1 / CAPACITY: 2,5 - 12 L/min. / CAVITY: T-31A
Synchronizing flow divider/combiners are sliding-spool, pressure-compensated devices used to split flow in onedirection and combine flow in the opposite direction. With a sychronizing feature, these valves can be used to allowtwo hydraulic cylinders to fully stroke and synchronize at the end of the stroke. When the first cylinder has reachedthe end of its stroke, a pressure-compensated, reduced flow is metered to or from the second cylinder until it alsoreaches the end of its stroke.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±3.0%Divisional Accuracy at Max Input Flow 50% ±2.0%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990031007Seal kit - Cartridge Polyurethane: 990031002Seal kit - Cartridge Viton: 990031006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FSBS
Model Code Example: FSBSXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 119 of 158
MODELFSDR
High accuracy synchronizing, flow divider-combiner valveSERIES 2 / CAPACITY: 6 - 30 L/min. / CAVITY: T-32A
High accuracy, synchronizing flow divider/combiners are sliding-spool, pressure-compensated devices used to splitflow in one direction and combine flow in the opposite direction. With a sychronizing feature, these valves can beused to allow two hydraulic cylinders to fully stroke and synchronize at the end of the stroke. When the firstcylinder has reached the end of its stroke, a pressure-compensated, reduced flow is metered to or from the secondcylinder until it also reaches the end of its stroke.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±3.0%Divisional Accuracy at Max Input Flow 50% ±2.0%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990032007Seal kit - Cartridge Polyurethane: 990032002Seal kit - Cartridge Viton: 990032006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/FSDR
Model Code Example: FSDRXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 120 of 158
MODELFSER
High accuracy synchronizing, flow divider-combiner valveSERIES 3 / CAPACITY: 12 - 60 L/min. / CAVITY: T-33A
High accuracy, synchronizing flow divider/combiners are sliding-spool, pressure-compensated devices used to splitflow in one direction and combine flow in the opposite direction. With a sychronizing feature, these valves can beused to allow two hydraulic cylinders to fully stroke and synchronize at the end of the stroke. When the firstcylinder has reached the end of its stroke, a pressure-compensated, reduced flow is metered to or from the secondcylinder until it also reaches the end of its stroke.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±2.5%Divisional Accuracy at Max Input Flow 50% ±1.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990033007Seal kit - Cartridge Polyurethane: 990033002Seal kit - Cartridge Viton: 990033006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/LH Mild Steel, Zinc-Nickel
snhy.com/FSER
Model Code Example: FSERXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 121 of 158
MODELFSFR
High accuracy synchronizing, flow divider-combiner valveSERIES 4 / CAPACITY: 23 - 120 L/min. / CAVITY: T-34A
High accuracy, synchronizing flow divider/combiners are sliding-spool, pressure-compensated devices used to splitflow in one direction and combine flow in the opposite direction. With a sychronizing feature, these valves can beused to allow two hydraulic cylinders to fully stroke and synchronize at the end of the stroke. When the firstcylinder has reached the end of its stroke, a pressure-compensated, reduced flow is metered to or from the secondcylinder until it also reaches the end of its stroke.
TECHNICAL DATAMaximum Operating Pressure 350 barDivisional Accuracy at Minimum Input Flow 50% ±2.5%Divisional Accuracy at Max Input Flow 50% ±1.5%Pressure Drop at Minimum Rated Input Flow 2 barPressure Drop at Maximum Rated Input Flow 24 barSeal kit - Cartridge Buna: 990034007Seal kit - Cartridge Polyurethane: 990034002Seal kit - Cartridge Viton: 990034006
(X)CONTROLX Not Adjustable
(A)FLOW SPLITA 50/50
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/FSFR
Model Code Example: FSFRXANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 122 of 158
MODELLRBC
Normally closed, modulating elementCAPACITY: 30 L/min. / CAVITY: T-163A
Normally closed modulating elements without an internal orifice act as a bypass compensator to maintain aconstant pressure drop across an orifice, regardless of variations in upstream or downstream pressure.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990163007Seal kit - Cartridge Polyurethane: 990163002Seal kit - Cartridge Viton: 990163006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(H)DIFFERENTIAL PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/LRBC
Model Code Example: LRBCXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 123 of 158
MODELLRDC
Normally closed, modulating elementSERIES 1 / CAPACITY: 60 L/min. / CAVITY: T-11A
Normally closed modulating elements without an internal orifice act as a bypass compensator to maintain aconstant pressure drop across an orifice, regardless of variations in upstream or downstream pressure.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990011007Seal kit - Cartridge Polyurethane: 990011002Seal kit - Cartridge Viton: 990011006
(X)CONTROLX Not Adjustable
(H)DIFFERENTIAL PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)G 150 psi (10,5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/LRDC
Model Code Example: LRDCXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 124 of 158
MODELLRFC
Normally closed, modulating elementSERIES 2 / CAPACITY: 120 L/min. / CAVITY: T-2A
Normally closed modulating elements without an internal orifice act as a bypass compensator to maintain aconstant pressure drop across an orifice, regardless of variations in upstream or downstream pressure.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990202007Seal kit - Cartridge Polyurethane: 990002002Seal kit - Cartridge Viton: 990202006
(X)CONTROLX Not Adjustable
(H)DIFFERENTIAL PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)G 150 psi (10,5 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/LRFC
Model Code Example: LRFCXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 125 of 158
MODELLRHC
Normally closed, modulating elementSERIES 3 / CAPACITY: 240 L/min. / CAVITY: T-17A
Normally closed modulating elements without an internal orifice act as a bypass compensator to maintain aconstant pressure drop across an orifice, regardless of variations in upstream or downstream pressure.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990017007Seal kit - Cartridge Polyurethane: 990017002Seal kit - Cartridge Viton: 990017006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(H)DIFFERENTIAL PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)G 150 psi (10,5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/LRHC
Model Code Example: LRHCXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 126 of 158
MODELLRJC
Normally closed, modulating elementSERIES 4 / CAPACITY: 480 L/min. / CAVITY: T-19A
Normally closed modulating elements without an internal orifice act as a bypass compensator to maintain aconstant pressure drop across an orifice, regardless of variations in upstream or downstream pressure.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990019007Seal kit - Cartridge EPDM: 990019014Seal kit - Cartridge Polyurethane: 990019002Seal kit - Cartridge Viton: 990019006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(H)DIFFERENTIAL PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)G 150 psi (10,5 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/LRJC
Model Code Example: LRJCXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 127 of 158
MODELLRBA
Normally closed, modulating element with pilot source from port 1CAPACITY: 30 L/min. / CAVITY: T-163A
Normally closed modulating elements with an internal orifice between port 1 and port 3 can be used as a main-stage relief valve. The valve can be controlled remotely using a pilot relief or pilot solenoid valve.
TECHNICAL DATAMaximum Operating Pressure 350 barControl Pilot Flow 0,16 - 0,25 L/min.Control Orifice Diameter 0,4 mmSeal kit - Cartridge Buna: 990163007Seal kit - Cartridge Polyurethane: 990163002Seal kit - Cartridge Viton: 990163006
(L)CONTROLL Tuning Adjustment
(D)DIFFERENTIAL PRESSURED 50 psi (3,5 bar)F 100 psi (7 bar)H 200 psi (14 bar)
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/LRBA
Model Code Example: LRBALDNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 128 of 158
MODELLRDA
Normally closed, modulating element with pilot source from port 1SERIES 1 / CAPACITY: 60 L/min. / CAVITY: T-11A
Normally closed modulating elements with an internal orifice between port 1 and port 3 can be used as a main-stage relief valve. The valve can be controlled remotely using a pilot relief or pilot solenoid valve.
TECHNICAL DATAMaximum Operating Pressure 350 barControl Pilot Flow 0,16 - 0,25 L/min.Maximum Valve Leakage at 110 SUS (24 cSt) 15 cc/min.@70 barControl Orifice Diameter 0,4 mmSeal kit - Cartridge Buna: 990011007Seal kit - Cartridge Polyurethane: 990011002Seal kit - Cartridge Viton: 990011006
(X)CONTROLX Not Adjustable
(H)BIAS PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/LRDA
Model Code Example: LRDAXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 129 of 158
MODELLRFA
Normally closed, modulating element with pilot source from port 1SERIES 2 / CAPACITY: 120 L/min. / CAVITY: T-2A
Normally closed modulating elements with an internal orifice between port 1 and port 3 can be used as a main-stage relief valve. The valve can be controlled remotely using a pilot relief or pilot solenoid valve.
TECHNICAL DATAMaximum Operating Pressure 350 barControl Pilot Flow 0,16 - 0,25 L/min.Control Orifice Diameter 0,4 mmSeal kit - Cartridge Buna: 990202007Seal kit - Cartridge Polyurethane: 990002002Seal kit - Cartridge Viton: 990202006
(X)CONTROLX Not Adjustable
(H)BIAS PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)G 150 psi (10,5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/LRFA
Model Code Example: LRFAXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 130 of 158
MODELLRHA
Normally closed, modulating element with pilot source from port 1SERIES 3 / CAPACITY: 240 L/min. / CAVITY: T-17A
Normally closed modulating elements with an internal orifice between port 1 and port 3 can be used as a main-stage relief valve. The valve can be controlled remotely using a pilot relief or pilot solenoid valve.
TECHNICAL DATAMaximum Operating Pressure 350 barControl Pilot Flow 0,25 - 0,50 L/min.Control Orifice Diameter 0,53 mmSeal kit - Cartridge Buna: 990017007Seal kit - Cartridge Polyurethane: 990017002Seal kit - Cartridge Viton: 990017006
(X)CONTROLX Not AdjustableE External 4-SAE Port, Port 3 blockedL Tuning Adjustment
(H)BIAS PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)G 150 psi (10,5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/LRHA
Model Code Example: LRHAXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 131 of 158
MODELLRJA
Normally closed, modulating element with pilot source from port 1SERIES 4 / CAPACITY: 480 L/min. / CAVITY: T-19A
Normally closed modulating elements with an internal orifice between port 1 and port 3 can be used as a main-stage relief valve. The valve can be controlled remotely using a pilot relief or pilot solenoid valve.
TECHNICAL DATAMaximum Operating Pressure 350 barControl Pilot Flow 0,25 - 0,50 L/min.Control Orifice Diameter 0,53 mmSeal kit - Cartridge Buna: 990019007Seal kit - Cartridge Polyurethane: 990019002Seal kit - Cartridge Viton: 990019006
(X)CONTROLX Not Adjustable
(H)DIFFERENTIAL PRESSUREH 200 psi (14 bar)A 12 psiB 20 psi (1,5 bar)C 30 psi (2 bar)D 50 psi (3,5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/LRJA
Model Code Example: LRJAXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 132 of 158
MODELLRDS
Normally closed modulating element with shuttleSERIES 1 / CAPACITY: 60 L/min. / CAVITY: T-21A
A normally closed modulating element, used as a bypass compensator, ensures a constant pressure drop acrossan external orifice to create a pressure compensated flow control. The resulting flow remains constant regardless ofvariations in upstream or downstream pressure.
A ball shuttle connects the after orifice signal from the higher of port 3 or 4 to the pilot area.
TECHNICAL DATANominal Compensating Pressure 14 barMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990021007Seal kit - Cartridge Polyurethane: 990021002Seal kit - Cartridge Viton: 990021006
(X)CONTROLX Not Adjustable
(H)DIFFERENTIAL PRESSUREH 200 psi (14 bar)
(N)SEAL MATERIALN Buna-NV Buna-N
snhy.com/LRDS
Model Code Example: LRDSXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 133 of 158
MODELLPBC
Normally open, modulating elementCAPACITY: 30 L/min. / CAVITY: T-163A
Normally open modulating elements without an internal orifice act as a restrictive compensator to maintain aconstant pressure drop across an orifice, regardless of variations in upstream or downstream pressure.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990163007Seal kit - Cartridge Polyurethane: 990163002Seal kit - Cartridge Viton: 990163006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(H)DIFFERENTIAL PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/LPBC
Model Code Example: LPBCXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 134 of 158
MODELLPDC
Normally open, modulating elementSERIES 1 / CAPACITY: 60 L/min. / CAVITY: T-11A
Normally open modulating elements without an internal orifice act as a restrictive compensator to maintain aconstant pressure drop across an orifice, regardless of variations in upstream or downstream pressure.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990011007Seal kit - Cartridge Polyurethane: 990011002Seal kit - Cartridge Viton: 990011006
(X)CONTROLX Not Adjustable
(H)DIFFERENTIAL PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)G 150 psi (10,5 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/LPDC
Model Code Example: LPDCXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 135 of 158
MODELLPFC
Normally open, modulating elementSERIES 2 / CAPACITY: 120 L/min. / CAVITY: T-2A
Normally open modulating elements without an internal orifice act as a restrictive compensator to maintain aconstant pressure drop across an orifice, regardless of variations in upstream or downstream pressure.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990202007Seal kit - Cartridge Polyurethane: 990002002Seal kit - Cartridge Viton: 990202006
(X)CONTROLX Not Adjustable
(H)DIFFERENTIAL PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)G 150 psi (10,5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/LPFC
Model Code Example: LPFCXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 136 of 158
MODELLPFCL
Tuneable, normally open modulating elementSERIES 2 / CAPACITY: 120 L/min. / CAVITY: T-2A
Normally open modulating elements without an internal orifice act as a restrictive compensator to maintain aconstant pressure drop across an orifice, regardless of variations in upstream or downstream pressure.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990202007Seal kit - Cartridge Polyurethane: 990002002Seal kit - Cartridge Viton: 990202006
(D)DIFFERENTIAL PRESSURED 50 psi (3,5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/LH Mild Steel, Zinc-Nickel
snhy.com/LPFCL
Model Code Example: LPFCLDNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 137 of 158
MODELLPHC
Normally open, modulating elementSERIES 3 / CAPACITY: 240 L/min. / CAVITY: T-17A
Normally open modulating elements without an internal orifice act as a restrictive compensator to maintain aconstant pressure drop across an orifice, regardless of variations in upstream or downstream pressure.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990017007Seal kit - Cartridge EPDM: 990017014Seal kit - Cartridge Polyurethane: 990017002Seal kit - Cartridge Viton: 990017006
(X)CONTROLX Not Adjustable
(H)DIFFERENTIAL PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)G 150 psi (10,5 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/LPHC
Model Code Example: LPHCXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 138 of 158
MODELLPJC
Normally open, modulating elementSERIES 4 / CAPACITY: 480 L/min. / CAVITY: T-19A
Normally open modulating elements without an internal orifice act as a restrictive compensator to maintain aconstant pressure drop across an orifice, regardless of variations in upstream or downstream pressure.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990019007Seal kit - Cartridge Polyurethane: 990019002Seal kit - Cartridge Viton: 990019006
(X)CONTROLX Not AdjustableP External 1/4 NPTF Pilot Port, Port 3
Blocked
(H)DIFFERENTIAL PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)G 150 psi (10,5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/LPJC
Model Code Example: LPJCXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 139 of 158
MODELLPBA
Normally open, modulating element with pilot source from port 1CAPACITY: 30 L/min. / CAVITY: T-163A
These normally open modulating elements with an internal orifice between port 1 and port 3 can be used as amain-stage reducing valve. The valve can be controlled remotely using a pilot relief or pilot solenoid valve.
TECHNICAL DATAMaximum Operating Pressure 350 barControl Orifice Diameter 0,4 mmSeal kit - Cartridge Buna: 990163007Seal kit - Cartridge Polyurethane: 990163002Seal kit - Cartridge Viton: 990163006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(H)BIAS PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/LPBA
Model Code Example: LPBAXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 140 of 158
MODELLPDA
Normally open, modulating element with pilot source from port 1SERIES 1 / CAPACITY: 60 L/min. / CAVITY: T-11A
These normally open modulating elements with an internal orifice between port 1 and port 3 can be used as amain-stage reducing valve. The valve can be controlled remotely using a pilot relief or pilot solenoid valve.
TECHNICAL DATAMaximum Operating Pressure 350 barControl Pilot Flow 0,16 - 0,25 L/min.Control Orifice Diameter 0,4 mmSeal kit - Cartridge Buna: 990011007Seal kit - Cartridge Polyurethane: 990011002Seal kit - Cartridge Viton: 990011006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(H)BIAS PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/LPDA
Model Code Example: LPDAXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 141 of 158
MODELLPFA
Normally open, modulating element with pilot source from port 1SERIES 2 / CAPACITY: 120 L/min. / CAVITY: T-2A
These normally open modulating elements with an internal orifice between port 1 and port 3 can be used as amain-stage reducing valve. The valve can be controlled remotely using a pilot relief or pilot solenoid valve.
TECHNICAL DATAMaximum Operating Pressure 350 barControl Pilot Flow 0,16 - 0,25 L/min.Control Orifice Diameter 0,4 mmSeal kit - Cartridge Buna: 990202007Seal kit - Cartridge Polyurethane: 990002002Seal kit - Cartridge Viton: 990202006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(H)BIAS PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/LPFA
Model Code Example: LPFAXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 142 of 158
MODELLPHA
Normally open, modulating element with pilot source from port 1SERIES 3 / CAPACITY: 240 L/min. / CAVITY: T-17A
These normally open modulating elements with an internal orifice between port 1 and port 3 can be used as amain-stage reducing valve. The valve can be controlled remotely using a pilot relief or pilot solenoid valve.
TECHNICAL DATAMaximum Operating Pressure 350 barControl Pilot Flow 0,25 - 0,50 L/min.Control Orifice Diameter 0,53 mmSeal kit - Cartridge Buna: 990017007Seal kit - Cartridge Polyurethane: 990017002Seal kit - Cartridge Viton: 990017006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(D)BIAS PRESSURED 50 psi (3,5 bar)F 100 psi (7 bar)G 150 psi (10,5 bar)H 200 psi (14 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/LPHA
Model Code Example: LPHAXDNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 143 of 158
MODELLPJA
Normally open, modulating element with pilot source from port 1SERIES 4 / CAPACITY: 480 L/min. / CAVITY: T-19A
These normally open modulating elements with an internal orifice between port 1 and port 3 can be used as amain-stage reducing valve. The valve can be controlled remotely using a pilot relief or pilot solenoid valve.
TECHNICAL DATAMaximum Operating Pressure 350 barControl Pilot Flow 0,25 - 0,50 L/min.Control Orifice Diameter 0,53 mmSeal kit - Cartridge Buna: 990019007Seal kit - Cartridge Polyurethane: 990019002Seal kit - Cartridge Viton: 990019006
(X)CONTROLX Not AdjustableL Tuning Adjustment
(H)BIAS PRESSUREH 200 psi (14 bar)D 50 psi (3,5 bar)F 100 psi (7 bar)G 150 psi (10,5 bar)
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/LPJA
Model Code Example: LPJAXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 144 of 158
MODELLPJA8
Normally open, modulating element with integral T-8A control cavity and pilotsource from port 1SERIES 4 / CAPACITY: 480 L/min. / CAVITY: T-19A
These normally open modulating elements with an internal orifice between port 1 and port 3 can be used as amain-stage reducing valve. The valve can be controlled remotely using a pilot relief or pilot solenoid valve.
TECHNICAL DATAMaximum Operating Pressure 350 barControl Pilot Flow 0,25 - 0,50 L/min.Pilot Control Cavity T-8AControl Orifice Diameter 0,53 mmSeal kit - Cartridge Buna: 990019007Seal kit - Cartridge Polyurethane: 990019002Seal kit - Cartridge Viton: 990019006
(D)BIAS PRESSURED 50 psi (3,5 bar)
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/LPJA8
Compound cartridge (pilot and main stage) assembly information is provided for reference only. Cartridges must be ordered separately and assembled atpoint of use.NOTES
Model Code Example: LPJA8DNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 145 of 158
MODELLPDS
Normally open modulating element with shuttleSERIES 1 / CAPACITY: 60 L/min. / CAVITY: T-21A
A normally open modulating element, used as a restrictive compensator, ensures a constant pressure drop acrossan external orifice to create a pressure compensated flow control. The resulting flow remains constant regardless ofvariations in upstream or downstream pressure.
A ball shuttle connects the after orifice signal from the higher of port 3 or 4 to the pilot area.
TECHNICAL DATANominal Compensating Pressure 14 barMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990021007Seal kit - Cartridge Polyurethane: 990021002Seal kit - Cartridge Viton: 990021006
(X)CONTROLX Not Adjustable
(H)DIFFERENTIAL PRESSUREH 200 psi (14 bar)
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/LPDS
Model Code Example: LPDSXHNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 146 of 158
MODELLHDT
Normally open, bi-directional, modulating elementSERIES 1 / CAPACITY: 60 L/min. / CAVITY: T-31A
These bi-directional, normally open, modulating elements used with an external orifice, create a bi-directional,pressure compensated flow control.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990031007Seal kit - Cartridge EPDM: 990031014Seal kit - Cartridge Polyurethane: 990031002Seal kit - Cartridge Viton: 990031006
(X)CONTROLX Not Adjustable
(F)NOMINAL CONTROL PRESSUREF 100 psi (7 bar)D 50 psi (3,5 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/LHDT
Model Code Example: LHDTXFNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 147 of 158
MODELLHFT
Normally open, bi-directional, modulating elementSERIES 2 / CAPACITY: 120 L/min. / CAVITY: T-32A
These bi-directional, normally open, modulating elements used with an external orifice, create a bi-directional,pressure compensated flow control.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990032007Seal kit - Cartridge EPDM: 990032014Seal kit - Cartridge Polyurethane: 990032002Seal kit - Cartridge Viton: 990032006
(X)CONTROLX Not Adjustable
(F)NOMINAL CONTROL PRESSUREF 100 psi (7 bar)D 50 psi (3,5 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/LHFT
Model Code Example: LHFTXFNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 148 of 158
MODELLHHT
Normally open, bi-directional, modulating elementSERIES 3 / CAPACITY: 240 L/min. / CAVITY: T-33A
These bi-directional, normally open, modulating elements used with an external orifice, create a bi-directional,pressure compensated flow control.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990033007Seal kit - Cartridge EPDM: 990033014Seal kit - Cartridge Polyurethane: 990033002Seal kit - Cartridge Viton: 990033006
(X)CONTROLX Not Adjustable
(F)DIFFERENTIAL PRESSUREF 100 psi (7 bar)D 50 psi (3,5 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/LHHT
Model Code Example: LHHTXFNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 149 of 158
MODELLHDA
Bypass/restrictive, priority modulating elementSERIES 1 / CAPACITY: 60 L/min. / CAVITY: T-31A
Bypass/restrictive modulating elements, when combined with an external orifice, create a bypass/restrictive flowcontrol. Input flow (port 3) is directed to the priority or control flow at port 2. Once the priority requirements are met,excess flow is bypassed out port 4. The after-orifice signal is connected to port 1. The before-orifice design allowsboth pressure and flow to be controlled on the priority side of the circuit regardless of pressure in the bypass circuit.These valves work equally well in either closed or open center systems. Their main use is to allow after-marketaccessories to be driven off the host machine's hydraulic system without adding an additional pump.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990031007Seal kit - Cartridge Polyurethane: 990031002Seal kit - Cartridge Viton: 990031006
(X)CONTROLX Not Adjustable
(F)DIFFERENTIAL PRESSUREF 100 psi (7 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/LHDA
Model Code Example: LHDAXFNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 150 of 158
MODELLHFA
Bypass/restrictive, priority modulating elementSERIES 2 / CAPACITY: 120 L/min. / CAVITY: T-32A
Bypass/restrictive modulating elements, when combined with an external orifice, create a bypass/restrictive flowcontrol. Input flow (port 3) is directed to the priority or control flow at port 2. Once the priority requirements are met,excess flow is bypassed out port 4. The after-orifice signal is connected to port 1. The before-orifice design allowsboth pressure and flow to be controlled on the priority side of the circuit regardless of pressure in the bypass circuit.These valves work equally well in either closed or open center systems. Their main use is to allow after-marketaccessories to be driven off the host machine's hydraulic system without adding an additional pump.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990032007Seal kit - Cartridge EPDM: 990032014Seal kit - Cartridge Polyurethane: 990032002Seal kit - Cartridge Viton: 990032006
(X)CONTROLX Not Adjustable
(F)DIFFERENTIAL PRESSUREF 100 psi (7 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/LHFA
Model Code Example: LHFAXFNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 151 of 158
MODELLHHA
Bypass/restrictive, priority modulating elementSERIES 3 / CAPACITY: 240 L/min. / CAVITY: T-33A
Bypass/restrictive modulating elements, when combined with an external orifice, create a bypass/restrictive flowcontrol. Input flow (port 3) is directed to the priority or control flow at port 2. Once the priority requirements are met,excess flow is bypassed out port 4. The after-orifice signal is connected to port 1. The before-orifice design allowsboth pressure and flow to be controlled on the priority side of the circuit regardless of pressure in the bypass circuit.These valves work equally well in either closed or open center systems. Their main use is to allow after-marketaccessories to be driven off the host machine's hydraulic system without adding an additional pump.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990033007Seal kit - Cartridge EPDM: 990033014Seal kit - Cartridge Polyurethane: 990033002Seal kit - Cartridge Viton: 990033006
(X)CONTROLX Not Adjustable
(F)DIFFERENTIAL PRESSUREF 100 psi (7 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/LHHA
Model Code Example: LHHAXFNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 152 of 158
MODELLHJA
Bypass/restrictive, priority modulating elementSERIES 4 / CAPACITY: 480 L/min. / CAVITY: T-34A
Bypass/restrictive modulating elements, when combined with an external orifice, create a bypass/restrictive flowcontrol. Input flow (port 3) is directed to the priority or control flow at port 2. Once the priority requirements are met,excess flow is bypassed out port 4. The after-orifice signal is connected to port 1. The before-orifice design allowsboth pressure and flow to be controlled on the priority side of the circuit regardless of pressure in the bypass circuit.These valves work equally well in either closed or open center systems. Their main use is to allow after-marketaccessories to be driven off the host machine's hydraulic system without adding an additional pump.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990034007Seal kit - Cartridge EPDM: 990034014Seal kit - Cartridge Polyurethane: 990034002Seal kit - Cartridge Viton: 990034006
(X)CONTROLX Not Adjustable
(F)DIFFERENTIAL PRESSUREF 100 psi (7 bar)E 75 psi (5 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/LHJA
Model Code Example: LHJAXFNCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 153 of 158
MODELRVBB
Normally closed modulating element valve with relief functionCAPACITY: 20 L/min. / CAVITY: T-163A
Three-port normally closed modulating elements with relief provide two functions when combined with an externalorifice. The mainstage is a bypass compensator that controls a priority flow into the circuit, determined by theexternal orifice. Input flow in excess of the priority flow is bypassed to tank (port 2). If the inlet (port 1) pressurerises to the valve setting, the valve operates as a normal relief valve.
TECHNICAL DATAFactory Pressure Settings Established at 15 L/min.Maximum Operating Pressure 350 barResponse Time - Typical 10 msMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barAdjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990163007Seal kit - Cartridge Polyurethane: 990163002Seal kit - Cartridge Viton: 990163006
(L)CONTROLL Standard Screw AdjustmentC Tamper Resistant - Factory SetK Handknob
(A)ADJUSTMENT RANGEA 75 - 3000 psi (5 - 210 bar), 1000 psi (70
bar) Standard SettingB 75 - 1500 psi (5 - 105 bar), 1000 psi (70
bar) Standard SettingC 75 - 6000 psi (5 - 420 bar), 1000 psi (70
bar) Standard SettingN 75 - 800 psi (5 - 55 bar), 400 psi (28
bar) Standard SettingQ 75 - 400 psi (5 - 28 bar), 200 psi (14
bar) Standard SettingW 75 - 4500 psi (5 - 315 bar), 1000 psi (70bar) Standard Setting
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/RVBB
Model Code Example: RVBBLANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 154 of 158
MODELRVCB
Normally closed modulating element valve with relief functionSERIES 1 / CAPACITY: 40 L/min. / CAVITY: T-11A
Three-port normally closed modulating elements with relief provide two functions when combined with an externalorifice. The mainstage is a bypass compensator that controls a priority flow into the circuit, determined by theexternal orifice. Input flow in excess of the priority flow is bypassed to tank (port 2). If the inlet (port 1) pressurerises to the valve setting, the valve operates as a normal relief valve.
TECHNICAL DATAFactory Pressure Settings Established at 15 L/min.Maximum Operating Pressure 350 barResponse Time - Typical 10 msMaximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 barAdjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990011007Seal kit - Cartridge Polyurethane: 990011002Seal kit - Cartridge Viton: 990011006
(L)CONTROLL Standard Screw AdjustmentC Tamper Resistant - Factory SetK Handknob
(A)ADJUSTMENT RANGEA 100 - 3000 psi (7 - 210 bar), 1000 psi
(70 bar) Standard SettingB 50 - 1500 psi (3,5 - 105 bar), 1000 psi
(70 bar) Standard SettingC 150 - 6000 psi (10,5 - 420 bar), 1000
psi (70 bar) Standard Setting
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/RVCB
Model Code Example: RVCBLANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 155 of 158
MODELRVEB
Normally closed modulating element valve with relief functionSERIES 2 / CAPACITY: 80 L/min. / CAVITY: T-2A
Three-port normally closed modulating elements with relief provide two functions when combined with an externalorifice. The mainstage is a bypass compensator that controls a priority flow into the circuit, determined by theexternal orifice. Input flow in excess of the priority flow is bypassed to tank (port 2). If the inlet (port 1) pressurerises to the valve setting, the valve operates as a normal relief valve.
TECHNICAL DATAFactory Pressure Settings Established at 15 L/min.Maximum Operating Pressure 350 barResponse Time - Typical 10 msMaximum Valve Leakage at 110 SUS (24 cSt) 50 cc/min.@70 barAdjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990202007Seal kit - Cartridge Polyurethane: 990002002Seal kit - Cartridge Viton: 990202006
(L)CONTROLL Standard Screw AdjustmentC Tamper Resistant - Factory SetK HandknobW Hex Wrench AdjustmentY Tri-Grip Handknob
(A)ADJUSTMENT RANGEA 100 - 3000 psi (7 - 210 bar), 1000 psi
(70 bar) Standard SettingB 50 - 1500 psi (3,5 - 105 bar), 1000 psi
(70 bar) Standard SettingC 100 - 6000 psi (7 - 420 bar), 1000 psi
(70 bar) Standard SettingW 100 - 4500 psi (7 - 315 bar), 1000 psi
(70 bar) Standard Setting
(N)SEAL MATERIALN Buna-NV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated
snhy.com/RVEB
Model Code Example: RVEBLANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 156 of 158
MODELRVGB
Normally closed modulating element valve with relief functionSERIES 3 / CAPACITY: 160 L/min. / CAVITY: T-17A
Three-port normally closed modulating elements with relief provide two functions when combined with an externalorifice. The mainstage is a bypass compensator that controls a priority flow into the circuit, determined by theexternal orifice. Input flow in excess of the priority flow is bypassed to tank (port 2). If the inlet (port 1) pressurerises to the valve setting, the valve operates as a normal relief valve.
TECHNICAL DATAFactory Pressure Settings Established at 15 L/min.Maximum Operating Pressure 350 barResponse Time - Typical 10 msMaximum Valve Leakage at 110 SUS (24 cSt) 65 cc/min.@70 barAdjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990017007Seal kit - Cartridge Polyurethane: 990017002Seal kit - Cartridge Viton: 990017006
(L)CONTROLL Standard Screw AdjustmentC Tamper Resistant - Factory SetK Handknob
(A)OPERATING RANGEA 100 - 3000 psi (7 - 210 bar), 1000 psi
(70 bar) Standard SettingB 150 - 1500 psi (10,5 - 105 bar), 1000
psi (70 bar) Standard SettingC 150 - 6000 psi (10,5 - 420 bar), 1000
psi (70 bar) Standard Setting
(N)SEAL MATERIALN Buna-NV Viton
snhy.com/RVGB
Model Code Example: RVGBLANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 157 of 158
MODELRVIB
Normally closed modulating element valve with relief functionSERIES 4 / CAPACITY: 320 L/min. / CAVITY: T-19A
Three-port normally closed modulating elements with relief provide two functions when combined with an externalorifice. The mainstage is a bypass compensator that controls a priority flow into the circuit, determined by theexternal orifice. Input flow in excess of the priority flow is bypassed to tank (port 2). If the inlet (port 1) pressurerises to the valve setting, the valve operates as a normal relief valve.
TECHNICAL DATAFactory Pressure Settings Established at 15 L/min.Maximum Operating Pressure 350 barResponse Time - Typical 10 msMaximum Valve Leakage at 110 SUS (24 cSt) 80 cc/min.@70 barAdjustment - Number of Clockwise Turns to Increase Setting 5Locknut Hex Size 15 mmLocknut Torque 9 - 10 NmSeal kit - Cartridge Buna: 990019007Seal kit - Cartridge EPDM: 990019014Seal kit - Cartridge Polyurethane: 990019002Seal kit - Cartridge Viton: 990019006
(L)CONTROLL Standard Screw AdjustmentC Tamper Resistant - Factory SetK Handknob
(A)ADJUSTMENT RANGEA 100 - 3000 psi (7 - 210 bar), 1000 psi
(70 bar) Standard SettingB 50 - 1500 psi (3,5 - 105 bar), 1000 psi
(70 bar) Standard SettingC 150 - 6000 psi (10,5 - 420 bar), 1000
psi (70 bar) Standard Setting
(N)SEAL MATERIALN Buna-NE EPDMV Viton
snhy.com/RVIB
Model Code Example: RVIBLANCONFIGURATION OPTIONS
Created on 11/05/2016 c© 2016 Sun Hydraulics Corporation See www.sunhydraulics.com for detailed product information 158 of 158
MODELLRFCL
Tuneable, normally closed, modulating elementSERIES 2 / CAPACITY: 120 L/min. / CAVITY: T-2A
Normally closed modulating elements without an internal orifice act as a bypass compensator to maintain aconstant pressure drop across an orifice, regardless of variations in upstream or downstream pressure.
TECHNICAL DATAMaximum Operating Pressure 350 barSeal kit - Cartridge Buna: 990202007Seal kit - Cartridge Polyurethane: 990002002Seal kit - Cartridge Viton: 990202006
(D)DIFFERENTIAL PRESSURED 50 psi (3,5 bar)F 100 psi (7 bar)
(N)SEAL MATERIALN Buna-NE EPDMV Viton
MATERIAL/COATINGStandard Material/Coating
/AP Stainless Steel, Passivated/LH Mild Steel, Zinc-Nickel
snhy.com/LRFCL
Model Code Example: LRFCLDNCONFIGURATION OPTIONS
www.sunhydraulics.com Rev. 11Feb15 | © 2015 Sun Hydraulics Corporation
Corporate Headquarters
1500 West University Parkway
Sarasota, FL 34243 U.S.A.
Phone: 941.362.1200
Sun Hydraulics Limited
Wheler Road
Coventry CV3 4LA
England
Ph: +44-2476-217-400
Sun Hydraulics Korea Corp.
92 Hogupo-ro
Namdong-gu
Incheon 405-818
Korea
Ph: +82-32-813-1350
Sun Hydraulik GmbH
Brüsseler Allee 2
D-41812 Erkelenz
Germany
Ph: +49-2431-8091-0
Sun Hydraulics China Co. Ltd
Hong Kong New World Tower
47th Floor
300, Huaihai Zhong Road
Shanghai 200021
P.R.China
Ph: +86-21-5116-2862
Sun Hydraulics Corporation
55 rue Fragonard
Résidence Rambouillet - Appt A-42
33520 Bruges
France
Ph: +33-673063371
Sun Hydraulics (India)
No. 48 ‘Regent Prime’
Unit No. 306, Level 3
Whiteield Main Road, Whiteield, Bangalore - 560 066India
Ph: +0091-80-28456325