fluke 1625 user training final
TRANSCRIPT
![Page 1: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/1.jpg)
Fluke-1625
GEO Earth Ground Testers
![Page 2: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/2.jpg)
Description of the Operating Elements
![Page 3: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/3.jpg)
Detail of Panel
66
![Page 4: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/4.jpg)
Panel Description
![Page 5: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/5.jpg)
Panel Description
![Page 6: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/6.jpg)
LCD Display
1. Digital display of measured value2. Measuring function field to display measuring
function3. Unit field: V, Ω, kΩ, Hz4. Special characters for operator guidance
![Page 7: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/7.jpg)
RA 2-pole, 3-pole MeasurementsTo make 2-pole or dead-earth measurements, connect a jumper between terminals H/C2 and S/P2 with the supplied connector cable. Refer to Figure. Then follow steps 1 thru 4 except use only earth electrode and the auxiliary earth electrode with minimum distance between them of 20 m.
A Select function RA 3-pole. Display is as shown below.
![Page 8: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/8.jpg)
![Page 9: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/9.jpg)
![Page 10: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/10.jpg)
RA 4-pole Measurements
![Page 11: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/11.jpg)
![Page 12: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/12.jpg)
RA 3-pole Selective Earth Resistance Measurement withCurrent Clamp
![Page 13: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/13.jpg)
![Page 14: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/14.jpg)
RA 4-pole Selective Earth Resistance Measurement withCurrent Clamp
![Page 15: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/15.jpg)
![Page 16: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/16.jpg)
Measurement of Resistances• Resistance Measurement (R~)
This measuring function determines the ohmic resistance between 0.001 Ω and
300 kΩ. The measurement is done with AC voltage. For measurements of very low resistances a compensation of the connecting leads is suggested (see “Compensation of Measuring Lead Resistance”).
![Page 17: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/17.jpg)
![Page 18: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/18.jpg)
• Resistance measurement (RF)
In this measuring mode all resistances from 0.001 Ω to 3 kΩ can be measured with
DC voltage and automatic polarity reversal as per EN61557-5. To achieve highest accuracy 4 pole measurements are possible. To balance the extension lead, a compensation has to be done.
![Page 19: Fluke 1625 user training final](https://reader030.vdocuments.net/reader030/viewer/2022020110/5594dd2f1a28ab6d328b45e6/html5/thumbnails/19.jpg)