form talysurf series 2
TRANSCRIPT
Taylor Hobson•/ P D C7 Г* I C I О МP R E C I S I O N
Form TalySurf Series 2A unique concept in form and
surface measurement
RM TALYSURF SERIES 2:Setting new standards for Form and
Now with [Jltra Windows NT™ software
Since its launch in 1989, the innovative Form Talysurf
Series has dominated the world market for form and
surfa* texture measurement. Nevertheless, our constant
drivefor advanced accuracy, speed and software capability
has led to the introduction of Form Talysurf Series 2,
incorporating pltra Windows NT™ software.
Flexible By DesignForm Talysurf Series 2 has been designed to meet the varied andchanging needs of industry. A choice of traverse units, softwareand accessories allow high precision surface finish and formmeasurements to be made on small, large or complex components,for laboratory design analysis or production batch measurements.
Form Talysurf Series 2 can offer complete flexibility for use inthe following ways:
Simultaneous form and surface finishHeasurement
Jser customisable interface
vogrammed, automated batch measurement
> On screen comparison to "master"component data
> Non contact measurement for delicateirfaces
) Three dimensional measurements with•-depth analysis and reporting
> Measurement and analysis of asphericalor conical components
> Advanced contour analysis
Revolutionary PrecisionThe nanometric resolution throughout its10mm (0.4in) gauge range makes the PGIthe most powerful gauging system availableon any form and surface texture instrument.
A significant benefit of Form Talysurf Series 2 is systemprogrammability which enables measurement in X, Y and Z axis(Y axis optional), analysis and results output to be madeautomatically, without operator intervention.
• H»' . . . . . i'-..... ..-., -o . :• ..... '.: • : : i
_
The pltra software menus are structured in a logical, easy tounderstand sequence.
The unique wide gauge range/high resolution of Form TalysurfSeries 2 allows highly accurate, simultaneous form, waviness andsurface measurement of components.
03-•
d Surface Texture Measurement
Interfere metric SystemThe 120mm PGI System ...
...A Revolut ionary Technology
High vertical gauge range (10mm)with gauge resolution of 12.8nm
Rotatable gauge for invertedmeasurement
Innovative new "snap off" stylus designto reduce possible pickup damage
Supplied column mounted with PC
Our constant drive to advance the measurement technologyavailable to industry has led to the introduction of the PGI
gauge. This unique and revolutionary interferometric transducer,a Phase Grating Interferometer, provides precise analysis of surfacetexture, form error, radius, inclination and dimensions in a singletraverse. The PGI offers a 10mm gauge range with 12.8nmresolution: this equates to a range to resolution ratio of780,000:1.
The diamond stylus clips onto the gauge using a new "snap off"connector, allowing the stylus to be ejected from the gaug|the force loaded on to the stylus exceeds safe limits. This[reduces possible damage to the gauge in the event of an oplerror. The pick-up cartridges accept a range of stylus arms [various measurement applications.
The gauge is mounted under the traverse unit which can opdin normal or inverted attitude and has high thermal stabililPGI systems incorporate a PC, motorised column and basqintegral joystick control panel.
The nanometric resolution throughout tru
10mm (0.4in) gauge range, makes the PGi
most powerful gauging system available on any
form and surface texture instrument.
120mm PGI System
RM TALYSURF SERIES 2:Inductive Systems
High accuracy straightness
Free standing or column mounted
(Absolute positional control
1mm gauge range with 16nm resolution10.04mm gauge range with 0.6nm resolution
150mm or 120mm traverse units
The versatile inductive traverse units offer high accuracystraightness over their traverse Length, having absolute positional
control throughout their traverse length, with fixed optical endstops at the limit of travel in either direction.
The inductive traverse units may be used free standing orcolumn mounted, in conjunction with a high specification DellPC. They can be used in automatic programmable or manualmode, or using an optional remote hand held controller.
luctive Pick-up options, for maximum flexibility
STANDARD INDUCTIVE PICK-UP Code 112/2564The inductive pick-up has a pivoted and balanced beam for anyattitude use with 1mm (0.039in) range styli. A range ofinterchangeable styli and skids is available (see page 14 ).
WIDE RANGE PICK-UP Code 112/2628The wide range inductive pick-up has a measuring range of28mrm(1.10in) and can detect form errors of less than 15um(бООип). Available as a plug-in accessory for the 50mm and120mni inductive units, it can be used in either column mountedor frfl standing systems. The wide range pick-up is suppliedwith I interchangeable stylus arms.
Resolution: 426nm (17uin)
NONJlONTACT GAUGE Code B112/2671Comprising a focus follower measuring head with a programmablecontroller for fast, simple set-up, the non-contact gauge can beused in place of inductive pick-ups for analysis of more sensitivecomponents, such as:
: and touch sensitive surfaces such as printing pastescoatings
: or dry solder pastes and printed conductive pastesntact and intraocular ophthalmic lenses
RanqdHesolution: ±500um/140nm± 50um/20nm
Right Angle Attachment (SKID) Code 112/2040 orRight Angle Attachment (SKIDLESS) Code 112/2022
A right angle measurementaccessory is available whichsupports the pick-up at rightangles for measuring betweenshoulders on components suchas crankshafts.
Non-Contact Gauge
50mm Traverse UnitThe most economical of the Form Talysurf Series 2 options, the50mm Traverse Unit can be used either free standing or columnmounted. The inductive gauge is mounted to an independentvertical height adjustment arrangement, which also enables thegauge to operate with or without a skid nosepiece.
120mm Traverse UnitThe 120mm Traverse Unit is ideal for longer measurements orwhere contour type measurement is required: when used with amotorised column it can accommodate the wide range pick-upaccessory for profile measurement. This traverse unit can also beused in free standing mode.
The inductive gauge is mounted to the traverse unit on a hingedpick-up stem, allowing the gauge to be used with or without askid nosepiece. Used skidless, the gauge can be inverted tomeasure the underside of a surface.
COLUMN OPTIONS
Motorised Column & Base
This epoxy granite, motorised column gives fully motorisedup/down and tilt movement, offering a rigid, stable base forprecise measurement. Two heights are available to give 450mm(17.7in) or 700mm (27.Sin) vertical traverse.
Both columns have a servo controlled motor drive and encoderto ensure absolute positional control. In addition, amanual/motorised tilt control is provided to allow the traverseunit to be adjusted (under computer control if required)parallel to the component being measured, thus reducing operatorsetup times. An adapter plate is available to extend the rangeof traverse tilt to 45 degrees in 15 degree increments.
Motorised column mounted configurations of Form TalysurfSeries 2 allow automatic stylus "stop on contact" with the workpiece,centred in the gauge range, enabling automatic "hands off"measurement of components.
The epoxy granite base has two integral tee slots for mountingworkholding accessories, the slots being parallel within 0.3mm(0.012in).
Manual Column & Base
For use with the 50mm and 120mm inductive traverse units, toprovide a cost effective alternative to the motorised columnand base.
Free Standing Brackets & Tilt Micrometers
The 50mm and 120mm traverse units (inductive systems) can beused free standing by the use of brackets, for the measurementof flat and arcuate surfaces.
FORM TALYSURF SERIES 2:Flexible Configuration to meet your changing needs
INDUCTIVE OPTIONS
50mm Traverse Unitshown in free standing mode
120mm Traverse Unit- shown in free standing mode
Optional Motorised or Manual Column
CHOOSEN
V
Inductive Pick-upcode 112/2564
Non-Contact Gaugecode B112/2671
PGI SYSTEM
Wide Range Pick-upcode 112/2628
The Form Talysurf Series 2 PGI system comprises:
• Traverse unit • Pick-up• Electronic Interface Unit • Motorised Column & Granite Base• DeskJet printer • PC Form and Surface Texture Analysis Software
COMPUTER OPTIONS
PCHigh specification Dell desktop PCs are supplied as standardwith all Form Talysurf Series instrument systems, ultra WindowsNT™ software, together with any additional modules, arepre-installed and tested at our Leicester head office.
Please refer to your Taylor Hobson representative for thelatest specification and details of Dell's worldwide customersupport at the time of purchase.
PrintersAn HP 895 CXi colour inkjet printer is supplied as standard withPGI systems and is optional with inductive. This allows fulladvantage to be taken of the colour output from ultra, Talymapand Contour software. The systems are also compatible with anoptional laser printer.
Taylomobson•r » •_/ VPRFriQIOM
0 10 20 30 40 50 60 70 £
FORM TALYSURF SERIES 2: Software
ndows NT™ interface providing clear screen presentation,lour hard copy of complex profiles and parameterlue data
werful add-on modules such as form, dual profile, asphericsd conies which offer enhanced functionality
Jyailable in multiple languages: English, French, German,Han, Spanish and Japanese.
« ;: •
II
Software Modules
Ultrindinee
Oth e
software has a range of optional modules to suitdual requirements and can be upgraded as yourchange. They must be ordered separately.
Form analysis (supplied standard on PGI system)
Aspheric analysis
Conic analysis
Enhanced Dual Profile
Contour analysis
Talymap 3D analysis
pedal software needs can be assessed on request.
Surface Finish Parameters
(standard with all systems)
Form Analysis Software
(standard with PGI systemsoptional with inductive systems)
Primary parameters: Pa, PC, Pda, Pdc, Pdq, PHSC, Pku,Pin, PLo, Plq, Pmr(c), Pp, PPc, Pq, PS, Psk, PSm, Pt, Pv,
PVo, Pz, Pz(JIS)
Roughness parameters: R3y, R3z, Ra, Re, Rda, Rdc, Rdq, RHSC,
Rku, Rln, RLo, Rlq, Rmr, Rmr(c), Rp, RPc, Rq, RS, Rsk, RSm, Rt,
Rv, RVo, Rz, Rz(JIS)
Waviness Parameters: Wa, We, Wda, Wdc, Wdq, WHSc, Wku,
Win, WLo, Wlq, Wmr, Wmr(c), Wp, WPc, Wq, WS, Wsk, WSm, Wt,
Wv, WVo, Wz
R+W Parameters: Ar, Aw, Pt, R, Rx, Sar, Saw, Sr, Sw, W, Wte, Wx
Rk Parameters: Al, A2, Mrl, Mr2, Rk, Rpk, Rvk
Aspheric Parameters(optional with 112/2845): Fig, Ra, Rt,
Smn, Smx, Tilt, Xp, Xt, Xv
Where applicable, the above parameters conform toand are named as per ISO standards 13565-1-2,4287-1997 and 12085.
Options for pltra FTSS112/2842 -01 - Base ultra software112/2843 -01 - Surface Finish Form112/2844 -01 - Surface Finish Conies112/2845 -01 - Surface Finish Aspherics112/2846 -01 - Surface Finish Dual Profile
Form Analysis Software Code 112/2345-01
In addition to the full range of surface texture parameters,this module provides:
Form error: calculated with reference to a best fit concaviconvex circular arc or straight line, including all surfaceroughness detail. Alternatively with reference to a minimuzone (which is the minimum separation between two paralllines containing the data set).
Radius: using a least squares best fit, concave or conveBcircular arcs, can be automatically calculated from selecteddata. The option to exclude unwanted surface features such asedges is also available. Alternatively, the absolute radius can beset to analyse the actual deviation from a design master. Othercalculated parameters include the centre co-ordinate and pitc|B
Angle: using a straight line or minimum zone algorithm]surface tilt can be determined and removed prior to paramejanalysis. Other calculated values include intercept and pitc
;ter
"Dimension: the linear relationship of surface features can beassessed and compared, due to the ability to calculate true Вand Z co-ordinate positions.
The above is standard on PGI systems and optional on Induj
Full explanations of the parameters listed are available in our Parameter Booklet - please ask your area representative for a copy.
В
MPREHENSIVE RANGE OF SOFTWARE:
Contour Software Analysis Code 112/2867-01
Fea
Indimea:foretigh
sis of contour measurement features such asangles, length and height, is available usingHobson's new Windows NFM based Contour
are which is fully compatible with ultra.
res include:
Mea urement Macros: These can be Learnt and edited to formuserrepeofd
•ograms for repeat measurement routines, cutting down:ive operator input; execution of programs is via a seriesnable "fastkeys".
dual feature tolerancing: Individual sections of therement template can be toleranced with varying values -mple a wide tolerance on a flat area of a surface and
r tolerances on radii.
Com arison of DXF files to contour: When measuring aknovw contour, "best fit" individual geometric elements arecalculated with reference to a template and the comparison of eachpoint in the contour against the nearest element in the template.
Geometric element fit to unknown contour: When measuringcomponents of an unknown contour, the software finds geometricelements that best suit the profile and determines the size, positionand relationship between profile features, plus other functions.
Radiusj
9.741
Height
55.916
to suit multiple applications
Aspheric Form SoftwareCode 112/2843-01
Aspherical Form: Assessments of form error, surface slope errorand tilt in comparison with operator defined design data, in theform of a polynomial expression.
Conical Form SoftwareCode 112/2844-01
Provides major and minor axes values and tilt, and residualsurface texture analysis after removal of best fit elliptical orhyperbolic forms.
Dual ProfileCode 112/2846-01
The surface geometry of complex asymmetrical components canbe analysed with the Dual Profile facility. This program allowsthe measurement profile of a master shape or prototype componentto be saved as a template. Subsequent components can bemeasured and simultaneously displayed with the template datafor immediate comparison.
re i Analyse Usei Щпйо* Help
Modified Profile 4.2.19.1 - test 5 - Reanaiysis RequiredAsph_02a - 33.836mm/Admin/Asph_02a.prf
30/04/99 07:69:402S/04/99 15:02:46
16 IB 20 23 74 28 29 30 32 34
•145791 mm769780.4049
-0.0140
Aspheric Form Software
а|иМя| N в) т|¥?| I Metric
i »|IH|«| -l.il
1
Modifiec
04-
0 3 -
D 2 -
0.1-
6 "-Q.1-
- 0 2 -
- 0 3 -
-[14-
Profile 4.2.19.2 - test 3 - P/9.820mm/Ellipse-HyperbolaHyp_17_7a - 8mm/Admin/Hyp_17_7a.prf
HalopreEsF1
05/05/9911:13:3829/04/9915:03:35
millimetres
042 ""OflnrinVfJif
90 S.5 1 0 C
SSI—
04
03
01
0 1
oo e
-01
-02
-03
-04
Ч Si ™
OflbHMI adM.r,
Conical Form Software
Cimworks™ SPC
Taylor Hobson, through partnership with Cimworks of the US,offer a range of market leading Cimworks SPC software solutions.These are fully compatible with ultra. Please contact your TaylorHobson representative for details of the most suitable productfor your application.
Dual Prc
2600-
2000-
1500-
1000-
500-
-500-
-1DCO-
-1SOO-
-5DOO-
-2500-
file - Test Bullet - 25mrrVAdmin/s3c 1 9/08/99Bullet - 25mrrVAdmin/s3c
С/V V Ч; •' / \/ \y Vy x--
14 16 IB 10 11 1Л IS 28 30 32 34 ЭЕ 38 40 42 44 4S 48 50 S2 54
3:51:36
2500
2000
1600
1000
600
о i=
-500
-1000
-150П
-2000
-2500
Current Point Max Difference TransformationX 21 0000 mm X 25 Э232 mm UX -0 0040 mmZ -477 2228 мгп Z 224 4895 urn UZ +755.3000 urn
UZ 757 2911 нгп uZ 761 2006 urn Angle 0 00 °
Dual Profile Software
3D TOPOGRAPHY MEASUREMENT
• Topography Measurement
Data for 3D analysis is collected by data logging a number ofparallel profiles at a pre-determined trace length and spacing,usingbhe translation stage below.
Translation Stage Code 112/2635A Y-axis stage, motor driven to ensure accurate sample spacingfor data logging parallel profiles of a component. (1pm stepresolution over 50mm total movement). The stage can be locatedin the tee slots of the Form Talysurf epoxy base.
3D Surface Texture CharacterisationTaylor Hobson is totally committed to the development of 3Dsurface texture characterisation. There are currently no definitiveinternational standards, therefore Taylor Hobson is activelyinvolved in the ISO project for 3D parameters and researchwhich will lead to definitive international standards.
[ of absolute position, relative position and continuousmovelient is achieved through software and an externalcontroller.
Inclination Stage Code 112/2275An optional inclination stage to provide precisely controlledtilt, used with the translation stage (112/2635).
Talymap 3D Topography[ftware
Talymap Software Talymap Basic BH2/2818, ExpertB11Z»819 & Universal B112/2820.
Talymap software allows a 3D surface to be viewed in a variety ofways to identify particular surface features. For example:
Axonometric projection II Wear simulation
Colour height representation • Form removal
Added features include zoom, truncation, dimensional measurementin X, Y and Z axes, view angle and rotation, single trace plot/zoom,least squares plane option, form removal for cylinder, sphere andpolynomial and profile inversion, displayed in monochrome orfull cflilour. Desk Top Publishing facilities allow comprehensivemeasurement reports to be created. For full details please requesta copy of our Talymap brochure.
CALIBRATION STANDARD
Advanced Calibration Techniquesfor optimum system repeatability
Three Line Calibration Standard Code 112/964.A three Line step height calibration standard can be supplied with any Form Talysurf Series 2traverse unit for calibration when surface texture only is to be analysed.
80mm (3.15in) Radius Calibration StandardCode 112/2028For a 120mm system using either the PGI gauge or wide range pick-up, the 80mm (3.15in) radiuscalibration standard is an essential accessory.
Radius Calibration Ball12.7mm (O.SOin) Code 112/2062
22mm (0.86in) Code 112/1844
For inductive systems using form or extended form softwarethese ball calibration standards are an essential requirement.The standards comprise a highly polished tungsten carbideprecision ball with housing and protective screw cap.
The 12.7mm (O.Sin) calibration ball (112/2062) is used withstandard 60mm stylus arms, the 22mm (0.86in) calibrationball (112/1844) being used with long stylus arms.
NB: 12.7mm Calibration Ball required for all miniature borestylus arms regardless of pick-up.
UKAS CALIBRATIONUKAS calibration certificates are available for all the above standards, giving a qualification of your instrument'saccuracies. The calibration is traceable to national standards and the uncertainty of measurement attains the highest approvedrating granted by UKAS.
UKAS calibration has reached mutual recognition agreements with many countries throughout the world. For more detailscontact our independent UKAS laboratory or ++44 116 246 3104 or e-mail [email protected].
STYLUS OPTIONS
A widp choice of pick-ups, styli, workholding accessoriesand furniture is available. If our standard accessories donot fit your requirement, our Applications Department willcustomise accessories to solve your measurement problem.
Stylus Stop Attachment Code 112/2098 Inductive, 112/2701 PGIFor use when measuring interrupted surfaces, this attachmentstops the stylus falling too far into the surface interrupt,thus preventing tip damage when it recontacts the surface whiletraversing.
ill 60mm length styli can be specified with the appropriateskid or nosepiece. A shoe nosepiece may be specified for surfacemeasurement when the cut-offs used are greater than 0.8mm(0.03|n).
120m(| length styli must be used skidless.
For the 120mm traverse unit, a hinged pick-up stem is available(112/2014) for both skid and skidless use. Alternatively asolid |ick-up stem (112/2015, supplied as standard on 120mmcolumn mounted system) may be specified for maximummeasu|ement loop rigidity when higher accuracies are required(skidless use only).
Inductive Stylus Arms
All stylus arms have 90° conisphere diamond styli with2um nominal radius tips unless otherwise stated.
The following styli are suitable for the inductive pick-upCode 112/2564 and 112/2008.
Standard Stylus Arm Code 112/2009Nominal range 1mm (0.039in)8.3mm
I
57.5
Ball Stylus Arm Code 112/2010Nominal range 2mm (0.078in) for form measurementSOOum radius sapphire ball stylus
16.5mm
117.5mm
Recess Stylus Arm Code 112/2011Nominal range 1mm (0.039in)
14.7mm
57.5mm
Small Bore Stylus Arm Code 112/2012Nominal range 1mm (0.039in)
1.2mm
57.5mm
Chisel Edge Stylus Arm Code 112/2013Nominal range 1mm (0.039in)2um x 750um chisel diamond stylus9.0mm
_J 57.5mm* »•
PGI Stylus Arms
The following styli are available for use with the PGIpick-up/traverse unit Code 112/2563
60° Standard Conisphere Stylus Arm Code 112/2689Nominal range 10mm (0.4in)
14.5mm
i60.0mm
Ball Stylus Arm Code 112/2620120mm, nominal range 20mm (O.Sin)
Ball Stylus Arm Code 112/2621150mm, nominal range 25mm (0.98in)
Both 500um sapphire ball styli
112/2620 - 27.8mm
112/2621 - 32.5mm
112/2620 - 120mm
112/2621 - 150mm
Small Bore Stylus Arm Code 112/2522Nominal range 10mm (0.4in)
1.9mm
I
I U. 60.0mm
Miniature Bore Stylus Arm Code 112/2623Nominal range 10mm (0.4in)
Recess Stylus Arm Code 112/2624Nominal range 10mm (0.4in)
Right Angle Stylus Arm Code 112/2625Nominal range 10mm (0.4-in)
Right Angle Rear Facing Stylus ArmCode 112/2626
Nominal range 10mm (0.4in)
13.8mm
*60.0mm
RM TALYSURF SERIES 2compre hensive Range of Accessories
ADJUSTABLE VEE BLOCK Code 112/1326
This accessory has 40mm (l.Sin) of lateral adjustment,particularly useful in bringing the crest of a cylindricalworkpiece directly under the stylus and in line with the axisof thjftiick-up traverse.
Т AXIS TABLE Code 112/1826Provides adjustment of the workpiece position in a direction 90°
to the traverse unit.
The total lateral adjustment of the table is 10mm (0.39in)minimum, indicated by a scaled knob. Table load capacity is20kg (44lb).
The Т axis table can also be used with the adjustable veeblock (112/1326) to position a cylindrical workpiece at right
angles to the pick-up traverse.
PAIR OF VEE BLOCKS Code 112/1645Suppott components such as crankshafts, which cannot be easilysupported on plain or adjustable vee blocks.
AUXILIARY LEVELLING TABLE Code 112/1634Provides a means to level a workpiece to bring its surface parallelto thA'ne of pick-up traverse. The table has a maximumadjustment of 3' and can be fitted with the adjusting wheeltowaras or away from the vertical column.
ADJUSTABLE WORKTABLE Code 112/1644Provides fine adjustment for rotational and lateral positioningof the workpiece. Range of rotational adjustment is ± 3°, range
of lateral adjustment ± 10mm (0.4in).
The adjustable worktable is particularly useful in bringing thecrest of a cylindrical workpiece directly under and in line withthe pick-up traverse.
UNIVERSAL WORKTABLE (Modular Construction)From the selection of components listed below a universalworktable incorporating X, Y and Z axes, rotary stage, tiltingstage and vee block can be configured.
The Universal Tables versatility can save time in setting upcomponents, in addition to having a large range of measuringapplications.
Components: (from top to bottom of illustration)
Vee Plates Code 112/2220
Simple Rotary Stage Code 112/2219
Graduated Rotary Stage Code 112/2218360° of movement, graduated in degrees with
5° of fine movement, graduated to ±0.5°.
Tilting Worktable Code 112/2214The worktable can be manually moved in 2 planes at90°, with a range of 2.5°.
25mm (lin) Linear Stage Code 112/2216To achieve orthogonal X and Y axis traverse use 2 linearstages.
Adapter Plate for 25mm (lin) Linear StageCode 112/2217
Location Dowels Code 112/2215
EYEPIECESUsed to facilitate the positioning of small workpieces relativeto the stylus during set-up.
X25 Eyepiece: Code 112/2194X10 Eyepiece: Code 112/2193Microscope Tube for the Eyepiece: Code 112/2192Microscope Stand for the Tube: Code 112/2190
A Camera with monitor can be specified as a special application.
TRAVERSE UNIT TILT ATTACHMENTCode 112/2060This provides 0, +15, +30 and +45° positions and in conjunctwith the motorised tilt enables the traverse unit to be tilteto +54°. (For use with inductive systems only).
REPLICA KIT Code 112/727Contains prepared quantities of materials for producing replidworkpiece surfaces inaccessible for direct stylus measuremaThe inherent surface texture of the replica material has an |about O.lum (4uin). It is limited to surfaces having an Ragreater than 0.2um (8uin). It is not possible to measure trjform with the kit.
ENVIRONMENTAL CABINET Code K510/944For additional protection against ambient conditions anenvironmental cabinet is available. Cabinets may also bespecified for the processing systems.
FURNITUREA range of instrument and accessory desks is available tothe Form Talysurf Series, computer and related items.
SPECIFICATIONтPGI
H N
Traverse LengthTraverse SpeedMeasuring Speeds
Return Speed
Gauge Type
Measuring RangeResolution
Range to Resolution RatioStraightness Accuracy
Data Resolution
Dimensions (LxDxH)Weight
TRAVERSE UNIT ACCURACIES
SKIDLESS
SURFACE TEXTUREParameters
FORM
To best fit straight line (P+V)
To best fit circular arc (P+V)
INCLINATIONTo best fit straight lineRangeAccuracy
RADIUS0.1 to 12.5mm (0.004 to O.Sin)
12.5 to 25mm (0.5 to l .Oin)
25 to 1000mm (1.0 to 40in)
1000 to 2000mm (40 to 80in)
120mm (4.72in)lOmm/sec (0.39in/sec) maximum1mm and 0.5mm/sec ±5%(0.04in and 0.02in/sec)
up to 5mm/sec (0.2in/sec)
Phase Grating Interferometer, ImN (lOOmg)force nominal10mm (0.39in)12.8nm @ 10mm range(O.Spin @ 0.39in range)
780,000:10.5pm over 120mm traverse(20uin over 4.72in)0.2pm over any 20mm traverse(Spin over any 0.78in)0.25pm (lOpin)396 x 127 x 195mm (15.6 x 5 x 7.7in)
11.5kg (23.3lb)
10mm (0.39in) range:(other stylus arms are available with extended range)
2% +4nm(0.16pin) (peak parameters only)
0.5pm over 120mm (20uin over 4.7in)0.25pm over 60mm (lOuin over 2.Sin)0.2pm over 20mm (Spin over 0.78in)0.2pm over 20mm (Spin over 0.78in)
Over centre 8mm (0.31in) range
±35'less than 0.5 arc mins
Over centre 8mm (0.31in) range:1 to 0.02% of nominal0.02% of nominal0.02 to 0.1% of nominal0.1% of nominal
18
D A T50mm Inductive 120mm Inductive
Traverse Length
Traverse Speed
Measuring Speeds
Return Speed
Gauge Type
Measuring Range
Resolution
Range to Resolution Ratio
Straightness Accuracy -
column mounted
free standing
Data Resolution
Dimensions (LxDxH)
Weight
TRAVERSE UNIT ACCURACIE
SKIDLESS
SURFACE TEXTURE
Parameters
FORM
To best fit straight line
(P+V)
To best fit circular arc
(p+v)
INCLINATION
To best fit straight line
Range
Accuracy
than 0.5 arc mins
RADIUS
0.1 to 12.5mm (0.004 to 0.5in)
12.5 to 25mm (0.5 to l.Oin)
25 to 1000mm (l.Oin to 40in)
Change in radius valuedue to temp, effects oninductive pick-ups
50mm (1.97in)
lOmm/sec (0.39in/sec) maximum
1mm and 0.5mm/sec ±5%
(0.04in and 0.02in/sec)
up to 5mm/sec
(0.2in/sec)
Inductive, ImN (lOOmg) force nominal
1mm (0.039in)
16nm @ 1mm range
(0.64pin @ 0.039in range)
3nm @ 0.2mm range
(0.12pin @ O.OOSin range)
О.бпт @ 0.04rnm range
(0.024|jin @ 0.0016in)
65,536:1
0.4pm over 50mm traverse
(16pin over 1.97in)
0.2pm over any 20mm traverse
(Spin over any 0.78in)
0.4pm over 50mm traverse
(16pm over 1.97in)
0.12pm over any 20mm traverse
(Spin over any 20mm traverse)
0.25pm (lOpin)
374 x 114 x 125mm (14.7 x 4.5 x 4.9in)
7kg (15.4lb)
120mm (4.72in)
lOmm/sec (0.39in/sec) maximum
1mm and 0.5mm/sec ±5%
(0.04in and 0.02in/sec)
up to 5mm/sec
(0.02in/sec)
Inductive, ImN (lOOmg) force nominal
1mm (0.039in)
16nm @ 1mm range
(0.64pin @ 0.039in range)
3nm @ 0.2mm range
(0.12uin @ O.OOSin range)
О.бпт @ 0.04mm range
(0.024pin @ 0.0016in range)
65,536:1
0.5pm over 120mm traverse
(20uin over 4.72in)
0.2pm over any 20mm traverse
(Spin over any OJSin)
1pm over 120mm traverse
(40pin/4.72in)
0.3pm over any 20mm traverse
(12pin/0.78in)
0.25pm (lOpin)
396 x 127 x 195mm (15.6 x 5 x 7.7in)
11.5kg (25.3lb)
1mm (0.039in) range:
other stylus arms are available with extended range
2% ±4nm(0.16pin) (peak parameters only)
0.4pm over 50mm (16pin over 1.97in)
0.2pm over 20mm (Spin over0.78in)
0.2pm over 9.5mm
(Spin over 0.37in)
±35'
less than 0.5 arc mins
1 to 0.02% of nominal
0.02% of nominal
0.02% to 0.1% of
nominal
4pm (160pin) per 'C on 12.5mm (0.5in) radius
Environmental cabinets are available on request
1mm (0.39in) range:
other stylus arms are available with extended range
2% ±4nm(0.16pin) (peak parameters only)
0.5pm over 120mm (20pin over 4.7in)
0.25pm over 60mm (lOpin over 2.Sin)
0.2pm over 20mm (Spin over 0.78in)
0.2pm over 9.5mm
(Spin over 0.37in)
±35'
less than 0.5 arc mins
1 to 0.02% of nominal
0.02% of nominal
0.02 to 0.1% of
nominal
4pm (160pin) per 'C on 12.5mm (O.Sin) radius
Taylor Hobson pursue a policy of continual improvements due to technical developments in all their instruments.We therefore reserve the right to depart from catalogue specifications.
19
О)
CD the measuring
solutionAt Taylor Hobson we don't sell products - we providesolutions. Whatever our customers' measuring needs, wewill find a solution to meet them.
Our reputation for excellence is based on more than 100jsign and manufacturing experience.
Add to this our worldwide coverage, our after salessupport and our commitment to customer care and youhave a company which provides its customers with totalpeace of mind.
The Taylor Hobson service:
Special applicationsWe have a team of engineers who provide a design servicefor dedicated metrology solutions. This can involvecustomising standard Taylor Hobson instruments to meetspecific requirements or designing unique products.
jf your local support centre phone-1-44 116 246 3186 or e-mail [email protected]
Centre of excellenceOur Centre of Excellence, based at our headquarters inLeicester, offers:
• product and theory training either at our Leicestertraining centre or at our customers' premises
• instrument and metrology advice
• a trial measurement service to help you decide whichproduct to buy
• lectures and presentations
Contact the Centre on+44 116 276 3779 ore-mail [email protected]
After sales supportTo ensure that all our products are maintained to thestandards you require, we offer a range of after salesservice packages. They include an on-site calibration
e and a refit and upgrade service.
We also offer an instrument calibration service at ourUKAS laboratory in Leicester.
For details of your local support centre phone+44 116 246 3135 ore-mail [email protected]
Taylor Hobson Limited
PO Box 36, 2 New Star Road, Leicester, LE4 9JQ, England.
Tel: +44 116 276 3771 • Fax: +44 116 274 1350
e-mail: [email protected]
Internet: http://www.taylor-hobson.com
Microsoft Windows and Windows NT are registered Trademarks of the Microsoft Corporation. FTSS 5E 8K CP0300
Taylor Hobson SA6 avenue de Norvege, Hightec 4,
91953 Courtaboeuf Cedex, France
Tel: +33 169 28 53 90 Fax: +33 169 28 33 37
e-mail: [email protected]
Taylor Hobson GmbHPostfach 4827, Kreuzberger Ring 6
65038 Wiesbaden, Germany
Tel: +49 611 973040 Fax: +49 611 97304600
e-mail: [email protected]
Taylor Hobson S.p.A.Via Vigentina 6-8,
20090 Opera, Milan, Italy
Tel: +39 0257 606424 Fax: +39 0257 606740
e-mail: [email protected]
Taylor Hobson Liaison Office
Austria and Eastern Europe
Amalienstrasse 68, A-1130 Vienna, Austria
Tel: +43 1877 557112 Fax: +43 1877 860516
e-mail: [email protected]
Taylor Hobson KKNo 31 Kowa Building 19-1, 3-Chome, Shiroganedai
Minato-Ku, Tokyo 108, Japan
Tel: +81 33473 7001 Fax: +81 33473 7002
e-mail: [email protected]
Taylor Hobson К INCHungkuk Life Insurance Bldg., 5th Floor 6-7, Soonae Dong
Pundang-Ku, Seongnam, kyungki-Do,463-020, Korea
Tel: +82 342 713 1371 Fax: +82 342 713 1372
e-mail: [email protected]
Taylor Hobson China Office
7/F, Corporation Square, 8 Lam Lok Street
Kowloon Bay, Hong Kong
Tel: +85 22757 3033 Fax: +85 22757 1767
e-mail: [email protected]
Taylor Hobson IncSuite 350, 2100 Golf Road, Rolling Meadows,
Illinois 60008, USA.
Tel: +1 847 290 8090 Fax: +1 847 290 1430
e-mail: [email protected]
ii
No. 0026 TAYLOR HOBSONA8248ISO9001