fum-t10-user menu-english video server de la enivision
TRANSCRIPT
![Page 1: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/1.jpg)
FUM-T10 Video Server User’s Manual
第 1 頁
VIDEO SERVER
USER MANUAL
![Page 2: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/2.jpg)
FUM-T10 Video Server User’s Manual
第 2 頁
Cautions
1. Read this user manual before use
2. Keep this user manual accessible
3. Follow instruction
4. Keep this unit away from cleanser
5. Keep this unit dry in ventilation
6. Give way to ventilation outlet
7. Power cord must be fixed properly
8. To avoid damage, unit must not be stuffed or be splashed with something
9. Do not repair this unit on your own
10. Please contact local dealer for the following condition:
a. Power cord damaged
b. Showered unit
c. Failure in operation
d. Unit dropped or cabinet damaged
11. Repairing components must be approved by original manufacturer.
12. Ground wire of outdoor image source must be well connected to the ground to prevent from
thunder attack
13. Power cord and outdoor image source cable should be detached in case of thunder attack
Warning Only qualified engineer can detach the cover. There is nothing inside for end users. Cover must not be removed in case of power on.
![Page 3: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/3.jpg)
FUM-T10 Video Server User’s Manual
第 3 頁
CONTENT
1. OUTLINE 1.1 INTRODUCTION ------------------------------------------ 4 1.2 FEATURE ---------------------------------------------------- 5 1.3 ACCESSORY ------------------------------------------------ 5 1.4 SYSTEM REQUIREMENT ------------------------------ 5 1.5 PANELS ------------------------------------------------------- 6 1.5.1 FRONT PANEL ------------------------------------------- 6 1.5.2 REAR PANEL --------------------------------------------- 6
2. INSTALLATION 2.1 CABLING ---------------------------------------------------- 8 2.2 SURVEILLANCE SOFTWARE ------------------------ 11 2.3 ETHERNET FRAMEWORK & CONNECTION -- 13 2.3.1 PC TO VIDEO SERVER CONNECTION --------- 13 2.3.2 INTRANET CONNECTION -------------------------- 17
3. OPERATION 3.1 LivePlayer SURVEILLANCE SOFTWARE --------- 20 3.1.1 LivePlay SOFTWARE INTERFACE ---------------- 20 3.1.2 LivePlayer INTERFACE SETUP --------------------- 22 3.2 IE BROWSER SETUP CAMERA FUNCTION ----- 30 3.2.1 Web Server AUTHORIZATION ---------------------- 31 3.2.2 Status ---------------------------------------------------- --- 32 3.2.3 View --------------------------------------------------------- 33 3.2.4 System ------------------------------------------------------ 35 3.2.5 Network ---------------------------------------------------- 36 3.2.6 Image ------------------------------------------------------- 37 3.2.7 User --------------------------------------------------------- 38 3.2.8 Alert -------------------------------------------------------- 39 3.2.9 Factory Default Function ------------------------------ 40 3.2.10 Restart Function --------------------------------------- 41 3.2.11 Upgrade -------------------------------------------------- 41
4. ELSE 4.1 SPECIFICATIONS --------------------------------------- 42
![Page 4: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/4.jpg)
FUM-T10 Video Server User’s Manual
第 4 頁
1. OUTLINE Video Server is a low cost provision of network surveillance facility which transmits images
on network to remote PC in format of compression technology. Monitoring, storage and
recognition on line are provided by video server. Image transmission remains the same quality on
both ends of server site and remote site. Single image source can be transmitted to multi ports
saving lots of cabling overhead.
1.1 INTRODUCTION
Dual compression technology JPEG & MPEG-4, remote site operator can access to the server
site via IE browser to secure personal safeguard and property. Video Server works with existing
digital network transmission system. LivePlayer software provides functions of live monitoring,
monitoring setup conditions & motion/schedule recording.
![Page 5: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/5.jpg)
FUM-T10 Video Server User’s Manual
第 5 頁
1.2 FEATURE
Image & audio transmission via network
Dynamic IP & static IP support
Dual compression technology JPEG & MPEG-4
Digital alarm I/O
RS-485 for PTZ control
LivePlayer client software
Built in motion detection & recording functions
IE browser remote monitoring & setup support
Firmware upgrade via IE browser on line
1.3 ACCESSORY
CD ROM
Remarks
[1] . Please contact local dealer in case of accessory shortage
[2] . Video server may be damaged & warranty void in use of other power adaptors
1.4 SYSTEM REQUIREMENT
Pentium4 or above
Windows 2000/XP OS
Protocol comply to 802.11 or ADSL network
Microsoft Internet Explorer 6.0 or above
Microsoft Codec Installation Package for Windows Media Player 6.4 or above
( http://www.microsoft.com/windows/windowsmedia/format/codecdownload.aspx )
![Page 6: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/6.jpg)
FUM-T10 Video Server User’s Manual
第 6 頁
1.5 PANELS
1.5.1 FRONT PANEL
Video In
Video input port takes images from camera or other image sources
Video Out Video output port provides images to monitor or recording devices
Audio In Audio input port takes audio from microphone or other audio devices
Reset Button Press this button to restart
RS-485 RS-485 control port for PTZ control
1.5.2 REAR PANEL
DC +12V
Power input port receives 12VDC power
![Page 7: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/7.jpg)
FUM-T10 Video Server User’s Manual
第 7 頁
LAN
RJ-45 10/100 Based-T Ethernet transmission port ALARM I/O
Alarm input/output port two sets for digital sensor input one set for digital alarm output
Definition of the pins
1. +12VDC
2. digital sensor input #1; Hi active
3. digital sensor # 2; Hi active
4. GND。
5. digital output out
6. digital output in
caution: pin #2 & pin #3 are individual input ports Hi active input voltage rated 12VDC
pin #5 & pin #6 are the same output port normal open alarm close
POWER LED
Power indicator power on indicator red
LAN LED Network indicator LED ON LAN working
![Page 8: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/8.jpg)
FUM-T10 Video Server User’s Manual
第 8 頁
2. INSTALLATION
2.1 CABLING
1. Power Input Plug in the power adaptor which supplies +12VDC. Video server could be damaged of
improper voltage input. Power LED turns to red in five seconds video server system activated.
2. Video Input Video source from camera or other device is to be connected to the “VIDEO IN" port.
Video source must be format of CVBS, 1 Vp-p Composite Video Signal, 75 Ω. Prior to video
input, camera or other device must be sure of working well. Other device could be DVR or VCR.
![Page 9: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/9.jpg)
FUM-T10 Video Server User’s Manual
第 9 頁
3. Plug in Ethernet Cable
Plug the cable in the Ethernet port with “LAN" mark for Ethernet connection.
4. Video Output “VIDEO OUTPUT" is to be connected to CCTV monitor for live monitoring. The video
output format is 1 Vp-p Composite Video Signal, 75 Ω
![Page 10: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/10.jpg)
FUM-T10 Video Server User’s Manual
第 10 頁
5. RS-485 Connection RS-485 --- Pan Tilt Control Port. User can setup pan tilt control on IE browser. Please
keep alert on the polarity D+ & D- of RS-485 port.
6. Audio Input “AUDIO IN" receives audio from microphone or other audio device.
![Page 11: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/11.jpg)
FUM-T10 Video Server User’s Manual
第 11 頁
2.2 SURVEILLANCE SOFTWARE
Please use the enclosed CD ROM to install the software 1. Put the CD ROM in CD drive 2. Execute the file “Liveplayer_Setup.exe” to start installation. This software promptly supports OS of English, traditional Chinese & simplified Chinese.
3. Click “Next” to initiate software
installation 4. Click “Next” in the dialog of “Choose Components” 5. Choose the default directory
![Page 12: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/12.jpg)
FUM-T10 Video Server User’s Manual
第 12 頁
6. Execute Codec Installation Package to download software via internet
7. Click “Close” upon installation finished
8. Click “start” ”program files”
”IPCam” ”LivePlayer”
![Page 13: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/13.jpg)
FUM-T10 Video Server User’s Manual
第 13 頁
2.3 ETHERNET FRAMEWORK & CONNECTION
Video Server can be connected to DSL modem or hub. Video server will start detecting
DHCP protocol upon power input. Video server enables DHCP protocol to work with NAT IP
address when NAT router in use. Default IP address 192.168.1.200 starts working when NAT
router not in use. Suppose 192.168.1.200has been occupied by other device. Other device must
be shut down beforehand until video server finishes IP setup.
2.3.1 PC TO VIDEO SERVER
CONNECTION
1. Use Cat5 Cross-over Cable to connect PC Cat5 Cross-over Cable (EIA 568A/B)layout & definition
2. Video server default setup as follows
![Page 14: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/14.jpg)
FUM-T10 Video Server User’s Manual
第 14 頁
3. Setup IP address of PC’s LAN card same as video server’s domain. In condition of Windowns-2000/XP OS a. Select “My Network Places” by clicking mouse on the right.
Click “properties” accordingly.
b. Select “Local Area Connection” by clicking mouse on the right. Click “Properties” accordingly.
c. Select ”TCP/IP” and click “Properties”
![Page 15: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/15.jpg)
FUM-T10 Video Server User’s Manual
第 15 頁
d. Select “Use the following IP address” to input IP address, Subnet mask and Default gateway. Click “OK” accordingly.
4. Follow the following procedure to make sure IP address correct.
a. Click “START” ”RUN” and input “cmd”. Click “OK”.
![Page 16: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/16.jpg)
FUM-T10 Video Server User’s Manual
第 16 頁
b. Enter DOS and input “ipconfig”. Click “enter” to inspect IP address, Subnet mask and Default gateway.
Please log out and log in if IP incorrect. 5. Connection
a. Execute the client software LivePlayer. Click “Setup” and “Refresh” to search video server. It takes time to search the video server. Please be patient. Alert dialog pops up upon video server found. Please review 3.1.2 for details.
![Page 17: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/17.jpg)
FUM-T10 Video Server User’s Manual
第 17 頁
b. Click “View” and “OK” to start connection.
2.3.2 INTRANET CONNECTION
1. Cat 5 cable must be used in condition of connection via router, DSL modem and hub.
![Page 18: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/18.jpg)
FUM-T10 Video Server User’s Manual
第 18 頁
2. Please make sure PC and video server same domain. 3. Video server detects DHCP when system starts working. Video server enables DHCP
protocol to accept IP address from NAT when NAT router detected. Default IP address
becomes 192.168.1.200 when NAT router not detected. Suppose there is an IP address
192.168.1.200 on internet. This device must be turned off prior to video server renew the
IP setup.
4. Connection a. Execute client software “LivePlayer”. Click “Setup” and “Refresh” to start video
server search. Please be patient for waiting video server search. Click “OK” by the time video server detected. Please review 3.1.2 for details.
![Page 19: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/19.jpg)
FUM-T10 Video Server User’s Manual
第 19 頁
b. Tick the item “View” and click “OK” to start connection.
![Page 20: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/20.jpg)
FUM-T10 Video Server User’s Manual
第 20 頁
3. OPERATION
3.1 LivePlayer SURVEILLANCE SOFTWARE Video Server provides LivePlay client software. Four units of video servers can be
monitored and managed at the same moment.
3.1.1 LivePlay SOFTWARE INTERFACE
1. LivePlay icon comes up on the desktop after installation. Double clicks on the mouse to
activate LivePlay software. Screen shot and control panel displays as follows:
2. Click “Change to Small Panel” for small size panel.
![Page 21: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/21.jpg)
FUM-T10 Video Server User’s Manual
第 21 頁
3. Definition of buttons in the control panel
Exit Exit LivePlayer
Hide the Panel Minimize LivePlayer
Quad View Viewing four channels at the same time
Single view Viewing single channel
Setting Entering setup menu to setup internet server, recording, system configuration,
alarm…… View recorded files
Click this button to execute the folder in explorer. Default directory can be found C:\Program files\IPCam. Recorded files can be found there.
Audio volume PC’s Sound Card Volume Adjustment Can monitor the sound at the remote site.
Mute Mute the sound of sound card.
Change to big panel/change to small panel Change the size of the panel.
Hide the status menu Hide the channel selection and alarm status to clarify the screen shot.
Camera 1-4 Inspect the intended channel in single channel status. Input audio in quad status.
motion detection status Motion Detection Indicator Video Server gives alert when motion detected.
Camera record status Recording Indicator PC keeps writing video files in the hard drive.
Digital input trigger status Digital Sensor Input Indicator Indicator of Digital Input Left --- Port # 1 Right --- Port # 2 Video Server comes with two digital input ports to receive alert from sensor.
Digital output alarm status Digital Alarm Output Indicator Indicator gives alert when video server delivers digital output.
![Page 22: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/22.jpg)
FUM-T10 Video Server User’s Manual
第 22 頁
3.1.2 LivePlayer INTERFACE SETUP
1. Refresh
Refresh function makes installation user-friendly.
a. Click “Setting” to activate LivePlayer software. b. Enter “Camera” setup mode.
c. Click ”Refresh” to detect NAT router and to add camera status in the list.
![Page 23: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/23.jpg)
FUM-T10 Video Server User’s Manual
第 23 頁
d. LivePlayer tells quantity of camera being added. e. Click OK
f. Tick up the camera items and click OK
g. Camera image comes up to the screen display
![Page 24: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/24.jpg)
FUM-T10 Video Server User’s Manual
第 24 頁
2. Add New Camera a. Fill in IP address to add up a new camera
b. Click “Test” to make sure
camera on line
c. Camera name and description will be seen and test indicator green in condition of well connected. Test indicator red in condition of camera disconnected.
d. Click “Add” to add the new camera to the list. Software will search the cameras in the list upon next activation.
![Page 25: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/25.jpg)
FUM-T10 Video Server User’s Manual
第 25 頁
e. If your router or your server requires Name and Password. Name and Password must be given. Click “Modify”.
f. Tick up “View” item, click “APPLY” and click “OK”.
g. Back to LivePlayer screen display.
![Page 26: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/26.jpg)
FUM-T10 Video Server User’s Manual
第 26 頁
3. Test on Camera Connection
a. Find a camera in the list. b. Click “Test” to make sure camera on line. c. Camera name and description will be seen and test indicator green in condition of well connected. Test indicator red in condition of camera disconnected.
4. Setup in IE Browser a. Click camera name in the list b. Click “Setup”. c. IE browser must be executed.
![Page 27: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/27.jpg)
FUM-T10 Video Server User’s Manual
第 27 頁
5. Recording Setup a. Browse Setup the location for saved video files.
b. Time Limit For Recording Setup recording time for a video file. File name will be changed upon time up.
c. Scheduled Recordings Users can choose a camera to setup its Scheduled Type, Start Time and Duration.
6. LivePlayer Password Setup a. Click “SYSTEM” to enter system setup mode.
b. Tick up “Enable” to start password setup. Password can be a single letter or
digit up to eight letters or digits. Users must keep password firmly in mind.
![Page 28: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/28.jpg)
FUM-T10 Video Server User’s Manual
第 28 頁
c. Password request pops out before entering setup mode. Input password to enter the system.
7. Superimpose camera information on the image view
a. Tick “Superimpose camera information on the image view” to input some information on the imge.
![Page 29: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/29.jpg)
FUM-T10 Video Server User’s Manual
第 29 頁
b. Click “Superimpose camera information on the image view” in the live mode to show time and date.
8. Alarm Setup a. Click “Alarm” to enter alarm setup. b. There are two event types.
One is motion detection the other Is Din. We can setup event type in alarm setup mode.
![Page 30: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/30.jpg)
FUM-T10 Video Server User’s Manual
第 30 頁
3.2 IE BROWSER SETUP CAMERA FUNCTION System manager can setup hardware via Goahead web server interface. Users must install
LivePlayer to modify device setup via IE browser.
Execute IE browser to input camera IP address or enter camera setup to click “CAMERA".
Both are used to modify camera setup.
Please execute “Restart" function before leaving.
![Page 31: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/31.jpg)
FUM-T10 Video Server User’s Manual
第 31 頁
The interface menu includes --- System, Network, Image, User, Alerts, States, View and Support
3.2.1 Web Server AUTHORIZATION
Different users have different limit on the web pages. Please read 3.2.7for detils.
Page Name Administrator View’s User Config’s User Everyone System YES NO YES NO Network YES NO YES NO Images YES NO YES NO User YES NO NO NO Alerts YES NO YES NO Status YES YES YES YES View YES YES YES YES* Support YES YES YES YES Factory Default YES NO YES NO Restart YES NO YES NO Upgrade YES NO YES NO
(1) YES stands for positive. NO stands for negative. (2) * is the mark for everyone in User Access option. If setup “Only users in database”
only User Database person can operate the page.
Sub menu
![Page 32: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/32.jpg)
FUM-T10 Video Server User’s Manual
第 32 頁
Default User Name & Password
User Name:admin
Password:passwd
User Name and Password can be changed at the first time. User name and Password must be kept carefully in mind. Tick “Save this password in your password list”. Password will be save in the remote site PC. 3.2.2 Status
Status includes device name, description, MAC address, IP address, Network Mask, Gateway,
Firmware Version, Built Date, Setup Date, Current Viewers.
![Page 33: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/33.jpg)
FUM-T10 Video Server User’s Manual
第 33 頁
3.2.3 View
View enables users to monitor camera. Provision of View: Scale Up, Scale Down, Record,
Snap……
Main Page Click “Main Page" for previous page.
Pan/Tilt Set Click down pull option of protocol to choose Fum-MMS or Pelco-D. Choose correct baud rate and ID. Connect Pan/Tilt and video server via RS-485 control port.
Pan/Tilt Control Click “Up/Down/Left/Right/Stop” to control Pan/Tilt.
Zoom/Focus Control Click “Zoom In/Zoom Out/Stop” to control zoom lens.
Auto Pan Pan/Tilt auto scanning feature.
Browse System saves the files in C:\ as default directory.
Message Display Tick “Time” & “Date” for time & date display. Tick “Text” for other display of “IP Address”, “Device Name” & “Description”.
Snap Please be aware of the directory of saving files prior to snap feature executed. System generates file name promptly. Format of the file is .Bmp.
![Page 34: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/34.jpg)
FUM-T10 Video Server User’s Manual
第 34 頁
Record Please remember the directory before record button executed. Record button will become stop button soon as recording starts. Filename will be generated to device name plus system time. Asf is the format of the file.
Scale Up Amplify the picture
Scale Down Minimize the picture
![Page 35: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/35.jpg)
FUM-T10 Video Server User’s Manual
第 35 頁
3.2.4 System Prior to system setup, User Name and Password are requested. System provides administrator with amendment on camera information, NTP protocol, IPaddress, email alert. Please click ok upon amendment finished.
System Settings
System settings are time, date and area. Device name is not a setting for administrator.
NTP NTP makes time rectification possible via time server. Time rectification can be pre-scheduled through local time server. NTP time server as follows: time.nist.gov
time-A.timefreq.bldrdoc.gov
tick.stdtime.gov.tw prefer
time.stdtime.gov.tw prefer
clock.stdtime.gov.tw
IP Address Notification Tick “Notify by E-Mail” and input email information. Video server will notify users IP address change by email.
![Page 36: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/36.jpg)
FUM-T10 Video Server User’s Manual
第 36 頁
3.2.5 Network DHCP, DDNS and HTTP can be modified in “Network”. Click OK upon information
amended.
IP Setting DHCP on video server detects and receives IP address from NAT network. IP address 192.168.1.200 will be used in condition of NAT router not detected. DHCP off video server works in static IP mode.
DDNS Please register on http://www.dyndns.com prior to DDNS setting.
Option HTTP control port Number: 80
![Page 37: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/37.jpg)
FUM-T10 Video Server User’s Manual
第 37 頁
3.2.6 Image Provides image format settings including resolution, compression quality and live mode
display. Picture quality adjustment includes brightness, contrast, sharpness and audio. Image rotation provides mirror and reversal function. Please click ok upon setting finished.
Video Settings Provides image format settings including resolution, compression quality and live mode display. There are three options on resolution: 640*240、320*240、160*128.
Power line frequency:50HZ/60HZ can be different from different area. Image
Quality: High/Normal/Low. Image quality will decline in condition of Max Frame
Rate. Default frame rate 30 is the second best.
Adjustment Provides adjustment on brightness, contrast and sharpness.
![Page 38: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/38.jpg)
FUM-T10 Video Server User’s Manual
第 38 頁
3.2.7 User Provides administrator information and password setting. Provides User Name and
Password setup also. Only users in the list are authorized to enter system setup. Administrator is the only user to get into user setup. Please click ok upon setup finished.
Admin Login User Name and Password can be created and amended in Admin Login. User Name and Password must be kept in mind firmly.
User Access Click “Everyone” for all users viewing via network. Click “Only users in database” for users in the list only viewing via network.
User Database
Administrator creates users in the list and gives authorization to the users. Input User Name and Password. Setup authorization in “Privilege” down pull bar. Click “Add” to save the information upon setup finished.
![Page 39: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/39.jpg)
FUM-T10 Video Server User’s Manual
第 39 頁
3.2.8 Alert Video server comes with external sensor input and motion detection. Setup parameters
can be modified. Record mode, email transmission and ftp upload can be pre-scheduled also. Please click ok upon setup finished.
Alerts Tick “Enable" to enable motion detection.
![Page 40: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/40.jpg)
FUM-T10 Video Server User’s Manual
第 40 頁
User can enable or disable Movement on image, Digital Input 1 and Digital Input 2 in
Detect Method. There are five degrees for the sensitivity of Movement on image.
Record mode, email transmission and ftp upload can be pre-scheduled in “Video Record”. System sends emails only if “No, e-mail notify only”. System sends recorded files if “Yes, and send recordings only”. System sends snap pictures if “Yes, and send snaps only”. Transmission can be email or ftp upload.
Recording Pre-record time, record time and Gap to next detect can be modified.
Create information about email transmission. FTP
Information must be correct for ftp upload. 3.2.9 Factory Default Function
Back to factory default. Everything will be back to the initial including User Name,
Password and IP address.
3.2.10 Restart Function
Better restart system after amendment. Live mode must be closed prior to restart
function. It takes time to finish restart function. System gets back to “Status” when restart finished. IP address should be given again if previous IP address changed while restarting.
![Page 41: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/41.jpg)
FUM-T10 Video Server User’s Manual
第 41 頁
3.2.11 Upgrade Firmware can be upgraded via IE browser.
![Page 42: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/42.jpg)
FUM-T10 Video Server User’s Manual
第 42 頁
4. ELSE
4.1 SPECIFICATIONS
Compression MPEG4 / JPEG
VGA 640x240
QVGA 320x240 Resolution
QQVGA 160x128
VGA (MPEG-4) 8 frames/sec
QVGA (JPEG ) 10 frames/sec Transmission Speed
QVGA (MPEG-4) 26 frames/sec
Network Protocol TCP/UDP/IP, DHCP,SMTP, HTTP, NTP/SNTP,DDNS, and TFTP
File Format AVI (MPEG-4/M-JPEG video stream with 32kbps ADPCM audio)
Recorded format AVI (MPEG-4/M-JPEG video stream with 32kbps ADPCM audio)
Movement on image Motion Detection
Digital Sensor
Email and file attached Alert Files
Transmission
ftp upload
IE Browser Internet Explorer 5.0 or above
IP setup
Image Mirror
Image Reversal
Brightness
Contrast
Sharpness
Pan/Tilt Control --- FUHO MMS / PELCO-D
Camera Setup via IE
Audio on/off
![Page 43: FUM-T10-User Menu-English Video Server de La Enivision](https://reader033.vdocuments.net/reader033/viewer/2022052410/54f5db5d4a795949198b468b/html5/thumbnails/43.jpg)
FUM-T10 Video Server User’s Manual
第 43 頁
Memory 2M Byte Flash ROM / 8M Byte SDRAM
network 10/100 Ethernet
X1 power input port
X1 RJ-45 network port
X1 audio port
Motion Detection Port
X1 Video Input Port
X1 Video Output Port
X1 System Reset
I/O Ports
X1 RS-485 Control Port
Dimension 100mm × 170mm × 30mm
Weight 800g
Power Input DC +12V
Power Consumption 400mA
Operating
Temperature 5°C ~ 40°C
Storage Temperature 0°C ~ 70°C
Humidity 10% ~ 80%