g-u tilt and turn and side hung jet ak8

8
Tilt-turn and Side hung fittings Tilt-turn, Side hung and Slave leaf fittings JET AK 8 for aluminium windows and doors

Upload: haltcol4567

Post on 16-Nov-2014

1.756 views

Category:

Documents


9 download

DESCRIPTION

Çift açılım aksesuarı,montaj çizimi

TRANSCRIPT

Page 1: G-U Tilt and Turn and Side Hung Jet AK8

Tilt-turn and Side hung fittings

Tilt-turn, Side hung and Slave leaf fittings JET AK 8for aluminium windows and doors

Page 2: G-U Tilt and Turn and Side Hung Jet AK8

2

Clampable JET AK 8 – for an economic production!

Advantages:■ RAL Test Certificate for the complete hardware system

■ Elegant, uniform styling of stay arm bearing and cornerbearing, flush with the sash overlap

■ All bearing parts completely clampable, thus no drillingnecessary

■ Stepless lateral and height adjustment

■ Pre-mounted structural components

■ Optionally with geared handle or mill-in gear withintegrated wrong operation safety device

■ Reversible for DIN left hand and DIN right hand

Range of applications:Sash width from 355 to 1700 mm

Sash height from 500 to 2400 mm

Sash weight to 80 kg, optional to 130 kgwith use of additional parts on hinge side

The programme of fittings JET AK 8 is adapted to windowswith a rebate clearance of 21 mm, Euro-groove 15 x 20 mmin the sash and groove 12 x 15, 14 x 18 or 10 x 14 mm inthe frame.

Page 3: G-U Tilt and Turn and Side Hung Jet AK8

3

Handles for easy operation

Handles for mill-in gearsHandle DIRIGENT-F Handle ADAGIO-FHandle DIRIGENT-F with push- Handle ADAGIO-F with push-button cylinder, to RAL 607/9 button cylinder, to RAL 607/9

Handle DIRIGENT Geared handle SPACIO(Alternative: ADAGIO-A)

Tilt-turn sash JET AK 8 withmill-in gear

Mill-in gears, 180°with wrong operation safetydevice are used for tilt-turnsashes; without wrong operationsafety device for side hung andtilt sashes (Handles DIRIGENTor ADAGIO-F as shown).

Tilt-turn sash JET AK 8 withwrong operation safety device

Clip hooks hold the mill-ingear securely in the hard-ware groove, even beforethe handle is installed.The backset is 14 mm.

Page 4: G-U Tilt and Turn and Side Hung Jet AK8

4

Corner bearing with hingeThe corner bearing with its axleis inserted into the pre-mountedframe casing. The clampingangle is pushed into the sashgroove and then screwed ontothe corner hinge.The hinge can be adjusted:sideways by ± 1 mm and inheight by ± 1.5 mm. The steplesslateral adjustment is made inside hung position of the sash.

Corner transmission4 stainless steel spring leavestransmit the thrust to thehorizontal rod without lossof stroke. Clamping screwssecure the seat of the cornertransmission in the profile.The sash pressure can beadjusted on the locking pin.

Adjustable locking pinsEccentric locking pins enableoptimised pressure and tight-ness of the sash.

Stay arm for tilt-turn sashesThis stay arm allows both left hand and right hand installation.Adjustment possibilities: lifting and lowering of sash ± 3 mm,sash pressure ± 1 mm, with 4 mm Allen key. Fastening on sashwith grub screw, thus no pre-drilling necessary.

Additional stay arm for tilt-turn sashesThe additional stay arm is only used for sash widths exceeding1400 mm and in connection with the stay arm size 50.It extends the range of applications for sash widths to 1700 mm.

Stay arm bearing mounted in secondsThe pre-mounted stay arm bearing is only inserted into theframe corner and fixed by tightening the clamping screws.The stay arm and the stay arm hinge are simply pushed together,quickly connected and secured by turning the stay arm bolt.

JET stay arms for easy installation of the sashes

Wrong operationsafety deviceIt is assembled together withthe handle fastening screwsin a single operation whichprevents triggering of the tiltposition when the sash is inside hung position.

Groove 12 x 15 Groove 14 x 18 Groove 10 x 14

Page 5: G-U Tilt and Turn and Side Hung Jet AK8

5

26

25

27

25

25

4

2 1

3

6 5

9

8

10

257

12 11

13

15

14

16

17

10

25

8

18

19

20

21

17

22

24

23

Tilt-turn fittings JET AK 8

Aluminium windows and doors,with geared handle or mill-in gearSingle parts

1 Geared handle2 Wrong operation safety device3 Mill-in gear

(instead of 1 and 2)4 Carrier5 Shoot bolt, bottom6 Tilt-locking plate7 Supporting plate8 Corner transmission (middle lock)9 Alignment wedge for sash

10 Locking pin element (middle lock)11 Corner bearing12 Casing for corner bearing13 Axle for corner bearing14 Corner hinge15 Clamping angle16 Countersunk screw17 Cover18 Axle for stay arm bearing19 Stay arm bearing20 Bearing sleeve21 Stay arm hinge22 Additional parts 130 kg23 Stay arm size 30, 50, 9024 Push rod size 50, 9025 Locking plate26 Additional stay arm (SW 1401–1700)27 Corner transmission

Total frame width TFW or total frame height TFHAssembly dimensions

Sash width SW or sash height SH

Page 6: G-U Tilt and Turn and Side Hung Jet AK8

6

24

3

1

7

8

97

6

4

24

1011

12

13

14

15

16

17

18

19

20

21

16

22

23

4

424

24

2

4

24

25

Aluminium windows and doors,with geared handle or mill-in gearSingle parts

1 Geared handle2 Carrier3 Mill-in gear without wrong operation

safety device(instead of 1 and 2)

4 Locking pin element5 Shoot bolt, bottom (middle lock)6 Tilt-locking plate (middle lock)7 Alignment wedge for frame8 Alignment wedge for sash9 Corner transmission

10 Corner bearing11 Casing for corner bearing12 Axle for corner bearing13 Corner hinge14 Clamping angle15 Countersunk screw16 Cover17 Middle bearing18 Axle for stay arm bearing19 Stay arm bearing20 Bearing sleeve21 Stay arm hinge22 Additional parts 130 kg23 Side hung sash hinge24 Locking plate25 Corner transmission (middle lock)

Side hung fittings JET AK 8

Total frame width TFW or total frame height TFHAssembly dimensions

Sash width SW or sash height SH

Page 7: G-U Tilt and Turn and Side Hung Jet AK8

7

Slave leaf fittings JET AK 8

23

22

16

21

20

19

18

17

16

15

13

14

12

10 11

24

9

8

7 6

5

3

4

2

1

26

6

25

2424

99

Single parts1 Slave leaf gear2 Key3 Keeper4 Shoot bolt, bottom5 Shoot bolt, bottom6 Locking plate for shoot7 Alignment wedge for sash8 Corner transmission9 Locking pin element

10 Corner bearing11 Casing for corner bearing12 Axle for corner bearing13 Corner hinge14 Clamping angle15 Countersunk screw16 Cover17 Middle bearing18 Axle for stay arm bearing19 Stay arm bearing20 Bearing sleeve21 Stay arm hinge22 Additional parts 130 kg23 Side hung sash hinge24 Locking plate25 Corner transmission26 Shoot bolt, top

Assembly dimensions

according to frame groove

Page 8: G-U Tilt and Turn and Side Hung Jet AK8

8 GB 373 a 11.03 MQ Printed in Germany

Application, specification

SpecificationTilt-turn windows and doorsTilt-turn fittings JET AK 8 according to scheme A (B, C, D, E),for sashes to 80 kg (130 kg).Clampable fittings for sashes with rebate clearance of 21 mm,Euro-groove 15 x 20 mm in the sash and groove 12 x 15,14 x 18 or 10 x 14 mm in the frame.Corner bearing adjustable + 2.5 mm or - 1.5 mm in height,± 1 mm laterally, stay arm adjustable ± 3 mm, sash pressureadjustment ± 1 mm.Identical shape of stay arm and corner bearings.The fittings with one handle operation are concealed within therebate. The locking pins of the gear parts, stay arms and cornertransmissions are adjustable.From a width of 1400 mm the sashes are equipped with anadditional stay arm.The corner transmissions are provided with rust-proof 4-leafsteel spring assemblies.

Side hung windows and doorsSide hung fittings JET AK 8 according to scheme A (A 1, B, C,D), for sashes to 80 kg (130 kg).Clampable fittings for windows with rebate clearance of21 mm, Euro-groove 15 x 20 mm in the sash and groove12 x 15, 14 x 18 or 10 x 14 mm in the frame.Corner bearing adjustable + 2.5 mm or - 1.5 mm in height,± 1 mm laterally, side hung sash hinge adjustable ± 3 mm,sash pressure adjustment ± 1 mm.Identical shape of stay arm and corner bearings.The fittings with one handle operation are concealed withinthe rebate. The locking pins of the gear parts and cornertransmissions are adjustable.The corner transmissions are provided with rust-proof 4-leafsteel spring assemblies.

Slave leaf windows and doorsSlave leaf fittings JET AK 8 according to scheme G (H, I),for sashes to 80 kg (130 kg).Clampable fittings for sashes with rebate clearance of 21 mm,Euro-groove 15 x 20 mm in the sash and groove 12 x 15,14 x 18 or 10 x 14 mm in the frame.Corner bearing adjustable + 2.5 mm or - 1.5 mm in height,± 1 mm laterally, side hung sash hinge adjustable ± 3 mm,sash pressure adjustment ± 1 mm.Identical shape of stay arm and corner bearings.The fittings with inactive sash gear or shoot bolt operation areconcealed within the rebate.The locking pins of the gear parts and corner transmissions areadjustable.The corner transmissions are provided with rust-proof 4-leafsteel spring assemblies.

Materials, protection against corrosionThe fitting parts are made of high quality steel, zinc die-castingand aluminium alloys.After zinc plating and standard bichromating surface treat-ment the zinc die-casting parts receive the additional silvercoloured coating ferGUard* silver.This particularly high quality sealed coating provides per-manent first class protection against corrosion for all surfaces(corresponds to future EU environmental protection require-ments). Aluminium parts are anodized or powder coated.The steel parts consist of stainless alloys.

A B C D E G H I

A A 1 B C D

Gretsch-Unitas GmbHBaubeschlägeD-71252 DitzingenPhone +49 7156 301-0Fax +49 7156 301-293Internet http://www.g-u.deE-Mail [email protected]

Gretsch-Unitas LtdUnitas House, Quinn CloseCoventry CV3 4LHPhone +44 24 76 21 79 00Fax +44 24 76 21 79 09Internet http://www.g-u.co.ukE-Mail [email protected]