ga h97m d3h (ga z97m d3h) english

GA-Z97M-D3HGA-H97M-D3H

User's ManualRev. 100112ME-Z97MD3H-1001R

GA-Z97M-D3H GA-H97M-D3H

Copyright 2014 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.The trademarks mentioned in this manual are legally registered to their respective owners.DisclaimerInformation in this manual is protected by copyright laws and is the property of GIGABYTE.Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice.No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission.

In order to assist in the use of this product, carefully read the User's Manual. For product-related information, check on our website at: http://www.gigabyte.com

Identifying Your Motherboard RevisionThe revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information.Example:

MotherboardGA-Z97M-D3HGA-H97M-D3H

Apr. 11, 2014

Apr. 11, 2014

Motherboard

GA-Z97M-D3HGA-H97M-D3H

- 3 -

Table of Contents

GA-Z97M-D3H/GA-H97M-D3H Motherboard Layout ......................................................4GA-Z97M-D3H/GA-H97M-D3H Motherboard Block Diagram .........................................5

Chapter 1 Hardware Installation .....................................................................................61-1 Installation Precautions .................................................................................... 61-2 Product Specifications ...................................................................................... 71-3 Installing the CPU ............................................................................................ 91-4 Installing the Memory ..................................................................................... 101-5 Installing an Expansion Card ......................................................................... 101-6 Back Panel Connectors .................................................................................. 101-7 Internal Connectors ........................................................................................ 12

Chapter 2 BIOS Setup ..................................................................................................182-1 Startup Screen ............................................................................................... 182-2 M.I.T. .............................................................................................................. 192-3 System Information ........................................................................................ 242-4 BIOS Features ............................................................................................... 252-5 Peripherals ..................................................................................................... 282-6 Power Management ....................................................................................... 302-7 Save & Exit ..................................................................................................... 32

Chapter 3 Appendix ......................................................................................................333-1 Configuring SATA Hard Drive(s) ..................................................................... 333-2 Drivers Installation .......................................................................................... 35

Regulatory Statements .............................................................................................. 36Contact Us ................................................................................................................ 40

- 4 -

The box contents above are for reference only and the actual items shall depend on the product package you obtain. The box contents are subject to change without notice.

Box Contents 5 GA-Z97M-D3H or GA-H97M-D3H motherboard 5 Motherboard driver disk 5 Two SATA cables 5 User's Manual 5 I/O Shield

GA-Z97M-D3H/GA-H97M-D3H Motherboard Layout

F_US

B30

KB_MS_USBCPU_FAN

LGA1150

ATX

AUDIODD

R3_4

DDR3

_2

DDR3

_3

DDR3

_1

BAT

ATX_12V_2X4

Intel Z97jIntel H97k

CODEC

CLR_CMOS

M_BIOSB_BIOS

VGA

DVI

USB3

0LA

N

PCIEX16

PCI1

PCI2

PCIEX4

SYS_FAN2

SYS_FAN1

GA-Z97M-D3H/GA-H97M-D3H

R_US

B30

HDMI

F_PANEL

SYS_FAN3F_USB3 F_USB1COMF_USB2

F_AUDIO

SPDIF_O

LPT TPM

SATA

31

35

02

4

Realtek GbE LAN

PCIe to PCI Bridge

iTE Super I/O

j Only for GA-Z97M-D3H.k Only for GA-H97M-D3H.

- 5 -

GA-Z97M-D3H/GA-H97M-D3H Motherboard Block Diagram

For detailed product information/limitation(s), refer to "1-2 Product Specifications."

iTE Super I/O

PS/2 KB/Mouse

LGA1150CPU

Intel Z97 jIntel H97 k

PCIe CLK(100 MHz)

PCIe CLK(100 MHz)

PCI CLK(33 MHz)

CPU CLK+/- (100 MHz)

1 PCI Express x16

COM

LPT

8 USB 2.0/1.1

2 PCI

6 USB 3.0/2.0

DDR3 1600/1333 MHz

PCI Express Bus

PCI Express Bus

6 SATA 6Gb/s

HDMI

DVI-D

D-Sub

DMI 2

.0

FDI

x16

x1

LAN

RJ45

Realtek GbE LAN

PCIe to PCI Bridge LPC

Bus

x4 x1

1 PCI Express x4

Cente

r/Sub

woofe

r Spe

aker

Out

Line O

utMI

C

Line I

n

S/PD

IF O

ut

Side

Spe

aker

Out

Rear

Spe

aker

Out

CODEC

Dual Channel Memory

Dual BIOS


- 6 -

Chapter 1 Hardware Installation1-1 Installation PrecautionsThe motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures:

Prior to installation, make sure the chassis is suitable for the motherboard. Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation. Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components. When connecting hardware components to the internal connectors on the motherboard, make

sure they are connected tightly and securely. When handling the motherboard, avoid touching any metal leads or connectors. It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity.

Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container.

Before unplugging the power supply cable from the motherboard, make sure the power supply has been turned off.

Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard.

Before using the product, please verify that all cables and power connectors of your hardware components are connected.

To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components.

Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.

Do not place the computer system on an uneven surface. Do not place the computer system in a high-temperature environment. Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user. If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certified computer technician.

- 7 -

1-2 ProductSpecifications

CPU Support for Intel Core i7 processors/Intel Core i5 processors/ Intel Core i3 processors/Intel Pentium processors/ Intel Celeron processors in the LGA1150 package(Go to GIGABYTE's website for the latest CPU support list.)

L3 cache varies with CPUChipset Intel Z97j/H97k Express ChipsetMemory 4 x DDR3 DIMM sockets supporting up to 32 GB of system memory

* Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than the size of the physical memory installed.

Dual channel memory architecture Support for DDR3 1600/1333 MHz memory modules Support for non-ECC memory modules Support for Extreme Memory Profile (XMP) memory modules

(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

Onboard Graphics

Integrated Graphics Processor:- 1 x D-Sub port, supporting a maximum resolution of 1920x1200@60Hz- 1 x DVI-D port, supporting a maximum resolution of 1920x1200@60Hz

* The DVI-D port does not support D-Sub connection by adapter.- 1 x HDMI port, supporting a maximum resolution of 4096x2160@24Hz or

2560x1600@60Hz* Support for HDMI 1.4a version.

- Support for up to 3 displays at the same time- Maximum shared memory of 1 GB

Audio Realtek ALC892 codec High Definition Audio 2/4/5.1/7.1-channel Support for S/PDIF Out

LAN Realtek GbE LAN chip (10/100/1000 Mbit)Expansion Slots 1 x PCI Express x16 slot, running at x16 (PCIEX16)

* For optimum performance, if only one PCI Express graphics card is to be installed, be sure to install it in the PCIEX16 slot.

(The PCIEX16 slot conforms to PCI Express 3.0 standard.) 1 x PCI Express x16 slot, running at x4 (PCIEX4)

(The PCIEX4 slot conforms to PCI Express 2.0 standard.) 2 x PCI slots

Multi-Graphics Technology Support for 2-Way AMD CrossFire

technology

Storage Interface Chipset:- 6 x SATA 6Gb/s connectors- Support for RAID 0, RAID 1, RAID 5, and RAID 10

USB Chipset:- 6 x USB 3.0/2.0 ports (4 ports on the back panel, 2 ports available through

the internal USB header)- 8 x USB 2.0/1.1 ports (2 ports on the back panel, 6 ports available through

the internal USB headers)


- 8 -

Internal Connectors

1 x 24-pin ATX main power connector 1 x 8-pin ATX 12V power connector 6 x SATA 6Gb/s connectors 1 x CPU fan header 3 x system fan headers 1 x front panel header 1 x front panel audio header 1 x S/PDIF Out header 1 x USB 3.0/2.0 header 3 x USB 2.0/1.1 headers 1 x serial port header 1 x parallel port header 1 x Clear CMOS jumper 1 x Trusted Platform Module (TPM) header

Back Panel Connectors

1 x PS/2 keyboard/mouse port 1 x D-Sub port 1 x DVI-D port 1 x HDMI port 4 x USB 3.0/2.0 ports 2 x USB 2.0/1.1 ports 1 x RJ-45 port 6 x audio jacks (Center/Subwoofer Speaker Out, Rear Speaker Out, Side Speaker

Out, Line In, Line Out, Mic In)

I/O Controller iTE I/O Controller ChipHardware Monitor

System voltage detection CPU/System temperature detection CPU/System fan speed detection CPU/System overheating warning CPU/System fan fail warning CPU/System fan speed control

* Whether the fan speed control function is supported will depend on the cooler you install.

BIOS 2 x 64 Mbit flash Use of licensed AMI UEFI BIOS Support for DualBIOS PnP 1.0a, DMI 2.7, SM BIOS 2.7, ACPI 2.0

Unique Features Support for APP Center* Available applications in APP Center may differ by motherboard model. Supported

functions of each application may also differ depending on motherboard specifications.

- @BIOS- EasyTune- EZ Setup- Fast Boot- ON/OFF Charge- Smart TimeLock- Smart Recovery 2- System Information Viewer- USB Blocker

- 9 -

1-3 Installing the CPURead the following guidelines before you begin to install the CPU: Make sure that the motherboard supports the CPU.

(Go to GIGABYTE's website for the latest CPU support list.) Always turn off the computer and unplug the power cord from the power outlet before installing the

CPU to prevent hardware damage. Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may

locate the notches on both sides of the CPU and alignment keys on the CPU socket.) Apply an even and thin layer of thermal grease on the surface of the CPU. Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage

of the CPU may occur. Set the CPU host frequency in accordance with the CPU specifications. It is not recommended

that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals. If you wish to set the frequency beyond the standard specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc.

Installing the CPULocate the alignment keys on the motherboard CPU socket and the notches on the CPU.

Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load plate automatically during the process of re-engaging the lever after you insert the CPU.

NotchAlignment KeyAlignment Key Notch

LGA1150 CPULGA1150 CPU Socket

Pin One Corner of the CPU Socket Triangle Pin One Marking on the CPU

Unique Features Support for Q-Flash Support for Smart Switch Support for Xpress Install

Bundled Software

Norton Internet Security (OEM version) Intel Rapid Start Technology Intel Smart Connect Technology Intel Smart Response Technology Intel Small Business Advantage k

Operating System Support for Windows 8.1/8/7

Form Factor Micro ATX Form Factor; 24.4cm x 22.5cm

* GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.

* Please visit the Support & Downloads\Utility page on GIGABYTE's website to check the supported operating system(s) for the software listed in the "Unique Features" and "Bundled Software" columns.

k Only for GA-H97M-D3H.

- 10 -

1-5 Installing an Expansion CardRead the following guidelines before you begin to install an expansion card: Make sure the motherboard supports the expansion card. Carefully read the manual that came

with your expansion card. Always turn off the computer and unplug the power cord from the power outlet before installing an

expansion card to prevent hardware damage.

DualChannelMemoryConfigurationThis motherboard provides four DDR3 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual Channel memory mode will double the original memory bandwidth.The four DDR3 memory sockets are divided into two channels and each channel has two memory sockets as following:

Channel A: DDR3_2, DDR3_4 Channel B: DDR3_1, DDR3_3

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.1. Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.2. When enabling Dual Channel mode with two or four memory modules, it is recommended that memory

of the same capacity, brand, speed, and chips be used and installed in the same colored DDR3 sockets. For optimum performance, when enabling Dual Channel mode with two memory modules, we recommend that you install them in the DDR3_1 and DDR3_2 sockets.

1-4 Installing the MemoryRead the following guidelines before you begin to install the memory: Make sure that the motherboard supports the memory. It is recommended that memory of the

same capacity, brand, speed, and chips be used.(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.

Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.

1-6 Back Panel Connectors

USB 2.0/1.1 PortThe USB port supports the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.PS/2 Keyboard/Mouse PortUse this port to connect a PS/2 mouse or keyboard.

When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.

When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.

- 11 -

After installing the HDMI device, make sure to set the default sound playback device to HDMI.

D-Sub PortThe D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of 1920x1200@60Hz (the actual resolutions supported depend on the monitor being used). Connect a monitor that supports D-Sub connection to this port.DVI-D Port (Note)The DVI-D port conforms to the DVI-D specification and supports a maximum resolution of 1920x1200@60Hz (the actual resolutions supported depend on the monitor being used). Connect a monitor that supports DVI-D connection to this port.HDMI Port

The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD Master Audio formats. It also supports up to 192KHz/24bit 8-channel LPCM audio

output. You can use this port to connect your HDMI-supported monitor. The maximum supported resolution is 4096x2160@24Hz or 2560x1600@60Hz, but the actual resolutions supported are dependent on the monitor being used.

Triple-DisplayConfigurationsfortheOnboardGraphics: Triple-display configurations are supported after you install motherboard drivers in OS. Only dual-display

configurations are supported during the BIOS Setup or POST process.

(Note) The DVI-D port does not support D-Sub connection by adapter.

Activity LEDConnection/Speed LED

LAN Port

Activity LED:Connection/Speed LED:State DescriptionOrange 1 Gbps data rateGreen 100 Mbps data rateOff 10 Mbps data rate

State DescriptionBlinking Data transmission or receiving is occurringOff No data transmission or receiving is occurring

USB 3.0/2.0 PortThe USB 3.0 port supports the USB 3.0 specification and is compatible to the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.RJ-45 LAN PortThe Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.

Center/SubwooferSpeakerOutJack(Orange)Use this audio jack to connect center/subwoofer speakers in a 5.1/7.1-channel audio configuration.

RearSpeakerOutJack(Black)This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration.

SideSpeakerOutJack(Gray)Use this audio jack to connect side speakers in a 7.1-channel audio configuration.

Line In Jack (Blue)The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.LineOutJack(Green)The line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration.

- 12 -

Mic In Jack (Pink)The Mic in jack. Microphones must be connected to this jack.

The audio jacks can be reconfigured to perform different functions via the audio software (supported functions may vary based on hardware specification). Only microphones still MUST be connected to the default Mic in jack.

1-7 Internal Connectors

1) ATX_12V_2X42) ATX3) CPU_FAN4) SYS_FAN1/2/35) SATA3 0/1/2/3/4/56) F_PANEL7) F_AUDIO8) SPDIF_O

9) F_USB3010) F_USB1/F_USB2/F_USB311) COM12) LPT13) TPM14) CLR_CMOS15) BAT

1 4 3 15

2

9

14

10

4

8

64117 1312

5

Read the following guidelines before connecting external devices: First make sure your devices are compliant with the connectors you wish to connect. Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices. After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

- 13 -

1/2) ATX_12V_2X4/ATX (2x4 12V Power Connector and 2x12 Main Power Connector) With the use of the power connector, the power supply can supply enough stable power to all the components

on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed. The power connector possesses a foolproof design. Connect the power supply cable to the power connector in the correct orientation.

The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will not start.

3/4) CPU_FAN/SYS_FAN1/SYS_FAN2/SYS_FAN3 (Fan Headers) All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.

When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

ATX_12V_2X4:

DEBUG PORT

G.QBOFM

131

2412

ATX

ATX:

Pin No. Definition Pin No. Definition1 3.3V 13 3.3V2 3.3V 14 -12V3 GND 15 GND4 +5V 16 PS_ON (soft On/Off)5 GND 17 GND6 +5V 18 GND7 GND 19 GND8 Power Good 20 -5V9 5VSB (stand by +5V) 21 +5V

10 +12V 22 +5V11 +12V (Only for 2x12-pin

ATX)23 +5V (Only for 2x12-pin ATX)

12 3.3V (Only for 2x12-pin ATX)

24 GND (Only for 2x12-pin ATX)

Pin No. Definition Pin No. Definition1 GND (Only for 2x4-pin 12V) 5 +12V (Only for 2x4-pin 12V)2 GND (Only for 2x4-pin 12V) 6 +12V (Only for 2x4-pin 12V)3 GND 7 +12V4 GND 8 +12V

CPU_FAN: SYS_FAN:Pin No. Definition

1 GND2 +12V3 Sense4 Speed Control

Pin No. Definition1 GND2 +12V/Speed Control3 Sense4 VCC

Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang.

These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.

SYS_FAN1/SYS_FAN2CPU_FAN

DEBUG PORT

G.QBOFMDEBUG PORT

G.QBOFM

1 1

ATX_12V_2X4

DEBUG PORT

G.QBOFM

5 8

1 4

SYS_FAN3

DEBUG PORT

G.QBOFM

1

To meet expansion requirements, it is recommended that a power supply that can withstand high power consumption be used (500W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system.

- 14 -

5) SATA3 0/1/2/3/4/5 (SATA 6Gb/s Connectors) The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s

standard. Each SATA connector supports a single SATA device. The Intel Chipset supports RAID 0, RAID 1, RAID 5, and RAID 10. Refer to Chapter 3, "Configuring SATA Hard Drive(s)," for instructions on configuring a RAID array.

Pin No. Definition1 GND2 TXP3 TXN4 GND5 RXN6 RXP7 GND

SATA3

7 1

7 1

DEBUG PORT

G.QBOFM1

35

02

4

DEBUG PORT

G.QBOFMDEBUG PORT

G.QBOFMDEBUG PORT

G.QBOFMDEBUG PORT

G.QBOFM

7 7

1 1

6) F_PANEL (Front Panel Header) Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator

on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PW (Power Switch): Connects to the power switch on the chassis front panel. You may

configure the way to turn off your system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management," for more information).

SPEAK (Speaker): Connects to the speaker on the chassis front panel. The system reports

system startup status by issuing a beep code. One single short beep will be heard if no problem is detected at system startup.

HD (Hard Drive Activity LED): Connects to the hard drive activity LED on the chassis front panel. The

LED is on when the hard drive is reading or writing data.

PLED/PWR_LED (Power LED):System Status LEDS0 OnS3/S4/S5 Off

Connects to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.

Hard Drive Activity LED

12

1920

CI- C

I+

MSG-

PW-

SPEA

K+

SPEA

K-MSG+

PW+

HD-

RES+

HD+

RES-

Reset Switch Chassis Intrusion

Header

Power Switch Speaker

F_USB30 F_U

B_

F_ F_

_B

BS_B

SB_B

_S

S__B

_U_B

S

123

123

123

1 2 3

1

1

1

1

BSS

S

_S

SSU

123

S3 BSSS U __ 3

F_USB3F

S _

S _

S _

SF

Power LED

Power LED

PWR_

LED-

PWR_

LED+

PWR_

LED-

RES (Reset Switch): Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer

if the computer freezes and fails to perform a normal restart. CI (Chassis Intrusion Header):

Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has been removed. This function requires a chassis with a chassis intrusion switch/sensor.

A RAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard drives are to be used, the total number of hard drives must be an even number.

A RAID 5 configuration requires at least three hard drives. (The total number of hard drives does not have to be an even number.)

A RAID 10 configuration requires four hard drives. To enable hot-plugging for the SATA ports, refer to Chapter 2, "BIOS Setup," "Peripherals\SATA Configuration,"

for more information.

- 15 -

7) F_AUDIO(FrontPanelAudioHeader) The front panel audio header supports Intel High Definition audio (HD) and AC'97 audio. You may connect

your chassis front panel audio module to this header. Make sure the wire assignments of the module connector match the pin assignments of the motherboard header. Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it.

12

910

For HD Front Panel Audio: For AC'97 Front Panel Audio:Pin No. Definition

1 MIC2_L2 GND3 MIC2_R4 -ACZ_DET5 LINE2_R6 GND7 FAUDIO_JD8 No Pin9 LINE2_L

10 GND

Pin No. Definition1 MIC2 GND3 MIC Power4 NC5 Line Out (R)6 NC7 NC8 No Pin9 Line Out (L)

10 NC

The front panel audio header supports HD audio by default. Audio signals will be present on both of the front and back panel audio connections simultaneously. Some chassis provide a front panel audio module that has separated connectors on each wire instead of a

single plug. For information about connecting the front panel audio module that has different wire assignments, please contact the chassis manufacturer.

8) SPDIF_O(S/PDIFOutHeader) This header supports digital S/PDIF Out and connects a S/PDIF digital audio cable (provided by expansion

cards) for digital audio output from your motherboard to certain expansion cards like graphics cards and sound cards. For example, some graphics cards may require you to use a S/PDIF digital audio cable for digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display to the graphics card and have digital audio output from the HDMI display at the same time. For information about connecting the S/PDIF digital audio cable, carefully read the manual for your expansion card.

Pin No. Definition1 SPDIFO2 GND1

9) F_USB30 (USB 3.0/2.0 Header) The header conforms to USB 3.0/2.0 specification and can provide two USB ports. For purchasing the

optional 3.5" front panel that provides two USB 3.0/2.0 ports, please contact the local dealer.

F_USB30 F_U

B_

F_ F_

_B

BS_B

SB_B

_S

S__B

_U_B

S

123

123

123

1 2 3

1

1

1

1

BSS

S

_S

SSU

123

S3 BSSS U __ 3

F_USB3F

S _

S _

S _

SF

10

20 1

11

Pin No. Definition Pin No. Definition Pin No. Definition1 VBUS 8 D1- 15 SSTX2-2 SSRX1- 9 D1+ 16 GND3 SSRX1+ 10 NC 17 SSRX2+4 GND 11 D2+ 18 SSRX2-5 SSTX1- 12 D2- 19 VBUS6 SSTX1+ 13 GND 20 No Pin7 GND 14 SSTX2+

Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket.

- 16 -

10) F_USB1/F_USB2/F_USB3 (USB 2.0/1.1 Headers) The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an

optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

Pin No. Definition Pin No. Definition1 Power (5V) 6 USB DY+2 Power (5V) 7 GND3 USB DX- 8 GND4 USB DY- 9 No Pin5 USB DX+ 10 NC

Pin No. Definition Pin No. Definition1 NDCD- 6 NDSR-2 NSIN 7 NRTS-3 NSOUT 8 NCTS-4 NDTR- 9 NRI-5 GND 10 No Pin

Do not plug the IEEE 1394 bracket (2x5-pin) cable into the USB header. Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord from the power

outlet to prevent damage to the USB bracket.

11) COM(SerialPortHeader) The COM header can provide one serial port via an optional COM port cable. For purchasing the optional

COM port cable, please contact the local dealer.

10

10

9

9

2

2

1

1

12) LPT (Parallel Port Header) The LPT header can provide one parallel port via an optional LPT port cable. For purchasing the optional

LPT port cable, please contact the local dealer.

Pin No. Definition Pin No. Definition Pin No. Definition1 STB- 10 GND 19 ACK-2 AFD- 11 PD4 20 GND3 PD0 12 GND 21 BUSY4 ERR- 13 PD5 22 GND5 PD1 14 GND 23 PE6 INIT- 15 PD6 24 No Pin7 PD2 16 GND 25 SLCT8 SLIN- 17 PD7 26 GND9 PD3 18 GND

DEBUG PORT

G.QBOFM

1226

25

- 17 -

20

19

2

1

F_USB30 F_U

B_

F_ F_

_B

BS_B

SB_B

_S

S__B

_U_B

S

123

123

123

1 2 3

1

1

1

1

BSS

S

_S

SSU

123

S3 BSSS U __ 3

F_USB3F

S _

S _

S _

SF

13) TPM (Trusted Platform Module Header) You may connect a TPM (Trusted Platform Module) to this header.

Pin No. Definition Pin No. Definition Pin No. Definition1 LCLK 8 LAD2 15 SB3V2 GND 9 VCC3 16 SERIRQ3 LFRAME 10 LAD1 17 GND4 No Pin 11 LAD0 18 NC5 LRESET 12 GND 19 NC6 NC 13 NC 20 SUSCLK7 LAD3 14 ID

14) CLR_CMOS(ClearCMOSJumper) Use this jumper to clear the BIOS configuration and reset the CMOS values to factory defaults. To clear

the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.

Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values. After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or manually

configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS configurations).

Open: Normal

Short: Clear CMOS Values

15) BAT (Battery) The battery provides power to keep the values (such as BIOS configurations, date, and time information)

in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery:1. Turn off your computer and unplug the power cord.2. Gently remove the battery from the battery holder and wait for one minute. (Or use a metal

object like a screwdriver to touch the positive and negative terminals of the battery holder, making them short for 5 seconds.)

3. Replace the battery.4. Plug in the power cord and restart your computer.

Always turn off your computer and unplug the power cord before replacing the battery. Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with an incorrect model. Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain

about the battery model. When installing the battery, note the orientation of the positive side (+) and the negative side (-) of the battery

(the positive side should face up). Used batteries must be handled in accordance with local environmental regulations.

- 18 -

Chapter2 BIOSSetupBIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup, saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows the user to modify basic system configuration settings or to activate certain system features.When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to keep the configuration values in the CMOS.To access the BIOS Setup program, press the key during the POST when the power is turned on.To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility. Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system. @BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the Internet

and updates the BIOS.

Because BIOS flashing is potentially risky, if you do not encounter problems using the current version of BIOS, it is recommended that you not flash the BIOS. To flash the BIOS, do it with caution. Inadequate BIOS flashing may result in system malfunction.

It is recommended that you not alter the default settings (unless you need to) to prevent system instability or other unexpected results. Inadequately altering the settings may result in system's failure to boot. If this occurs, try to clear the CMOS values and reset the board to default values. (Refer to the "Load Optimized Defaults" section in this chapter or introductions of the battery/clear CMOS jumper in Chapter 1 for how to clear the CMOS values.)

2-1 Startup ScreenThe following startup Logo screen will appear when the computer boots.(Sample BIOS Version: GA-Z97M-D3H F1i)

Function Keys

When the system is not stable as usual, select the LoadOptimizedDefaults item to set your system to its defaults. The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version.

There are three different BIOS modes as follows and you can use the key to switch between these modes.Startup Guide screen (default) simplifies conventional complicated BIOS setup menus and presents only the most frequently used options in the easy-to-use interface. It helps first-time users to perform basic system setups more quickly and easily. The ST Mode (for the GA-Z97M-D3H only) provides a fancy and user-friendly BIOS environment where users can easily point and click through various settings and make adjustments for optimum performance. Classic Setup is the conventional BIOS Setup interface where you can press the arrow keys on your keyboard to move among the items and press to accept or enter a sub-menu. Or you can use your mouse to select the item you want.

- 19 -

2-2 M.I.T.

Whether the system will work stably with the overclock/overvoltage settings you made is dependent on your overall system configurations. Incorrectly doing overclock/overvoltage may result in damage to CPU, chipset, or memory and reduce the useful life of these components. This page is for advanced users only and we recommend you not to alter the default settings to prevent system instability or other unexpected results. (Inadequately altering the settings may result in system's failure to boot. If this occurs, clear the CMOS values and reset the board to default values.)

This section provides information on the BIOS version, CPU base clock, CPU frequency, memory frequency, total memory size, CPU temperature, Vcore, and memory voltage.

` M.I.T. Current Status This screen provides information on CPU/memory frequencies/parameters.

& Performance Upgrade (Note) j Provides you with five different overclocking configurations. Options are: 20% Upgrade, 40% Upgrade,

60% Upgrade, 80% Upgrade, 100% Upgrade. (Default: Auto) & CPU Base Clock j

Allows you to manually set the CPU base clock in 0.01 MHz increments. (Default: Auto) Important: It is highly recommended that the CPU frequency be set in accordance with the CPU

specifications. & Host/PCIe Clock Frequency (Note) j

Allows you to manually set the host clock frequency (which controls CPU, PCIe, and memory frequencies) in 0.01 MHz increments.

This item is configurable only when CPU Base Clock is set to Manual. & Processor Base Clock (Gear Ratio) (Note) j

Allows you to configure the Processor Base Clock by multiplying the Host/PCIe Clock Frequency by several preset host clock multipliers. This item is configurable only when CPU Base Clock is set to Manual.

& Spread Spectrum Control (Note) j Enables or disables CPU/PCIe Spread Spectrum. (Default: Auto) This item is configurable only when CPU Base Clock is set to Manual.

(Note) This item is present only when you install a CPU that supports this feature. For more information about Intel CPUs' unique features, please visit Intel's website.

j Only for GA-Z97M-D3H.

- 20 -

` Advanced CPU Core Settings & CPU Clock Ratio, CPU Frequency

The settings above are synchronous to those under the same items on the Advanced Frequency Settings menu.

& KOC (Note) Allows for increased performance by using certain CPUs. (Default: Auto)

& CPU PLL Selection Allows you to set the CPU PLL. Auto lets the BIOS automatically configure this setting. (Default: Auto)

& Filter PLL Level Allows you to set the Filter PLL. Auto lets the BIOS automatically configure this setting. (Default: Auto)

& Uncore Ratio Allows you to set the CPU Uncore ratio. The adjustable range is dependent on the CPU being used.

& Uncore Frequency Displays the current CPU Uncore frequency.

& Intel(R) Turbo Boost Technology (Note) Allows you to determine whether to enable the Intel CPU Turbo Boost technology. Auto lets the BIOS

automatically configure this setting. (Default: Auto) & Turbo Ratio (1-Core Active~4-Core Active) (Note)

Allows you to set the CPU Turbo ratios for different number of active cores. Auto sets the CPU Turbo ratios according to the CPU specifications. (Default: Auto)

& Turbo Power Limit (Watts) Allows you to set a power limit for CPU Turbo mode. When the CPU power consumption exceeds the

specified power limit, the CPU will automatically reduce the core frequency in order to reduce the power. Auto sets the power limit according to the CPU specifications. (Default: Auto)

& Core Current Limit (Amps) Allows you to set a current limit for CPU Turbo mode. When the CPU current exceeds the specified current

limit, the CPU will automatically reduce the core frequency in order to reduce the current. Auto sets the power limit according to the CPU specifications. (Default: Auto)

& No. of CPU Cores Enabled (Note) Allows you to select the number of CPU cores to enable in an Intel multi-core CPU (the number of CPU

cores may vary by CPU). Auto lets the BIOS automatically configure this setting. (Default: Auto)


& Host Clock Value j This value is determined by multiplying the Host/PCIe Clock Frequency value by the Processor Base

Clock (Gear Ratio) value. & Processor Graphics Clock

Allows you to set the onboard graphics clock. The adjustable range is from 400 MHz to 4000 MHz. (Default: Auto)

& CPU Upgrade (Note) Allows you to set the CPU frequency. Options may vary depending on the CPU being used. (Default: Auto)

& CPU Clock Ratio Allows you to alter the clock ratio for the installed CPU. The adjustable range is dependent on the CPU

being installed. & CPU Frequency

Displays the current operating CPU frequency.


- 21 -

& Hyper-Threading Technology (Note 1) Allows you to determine whether to enable multi-threading technology when using an Intel CPU that

supports this function. This feature only works for operating systems that support multi-processor mode. Auto lets the BIOS automatically configure this setting. (Default: Auto)

& CPU Enhanced Halt (C1E) (Note 1) Enables or disables Intel CPU Enhanced Halt (C1E) function, a CPU power-saving function in system

halt state. When enabled, the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption. Auto lets the BIOS automatically configure this setting. (Default: Auto)

& C3 State Support (Note 1) Allows you to determine whether to let the CPU enter C3 mode in system halt state. When enabled, the

CPU core frequency and voltage will be reduced during system halt state to decrease power consumption. The C3 state is a more enhanced power-saving state than C1. Auto lets the BIOS automatically configure this setting. (Default: Auto)

& C6/C7 State Support (Note 1) Allows you to determine whether to let the CPU enter C6/C7 mode in system halt state. When enabled, the

CPU core frequency and voltage will be reduced during system halt state to decrease power consumption. The C6/C7 state is a more enhanced power-saving state than C3. Auto lets the BIOS automatically configure this setting. (Default: Auto)

& CPU Thermal Monitor (Note 1) Enables or disables Intel Thermal Monitor function, a CPU overheating protection function. When enabled,

the CPU core frequency and voltage will be reduced when the CPU is overheated. Auto lets the BIOS automatically configure this setting. (Default: Auto)

& CPU EIST Function (Note 1) Enables or disables Enhanced Intel Speed Step Technology (EIST). Depending on CPU loading, Intel

EIST technology can dynamically and effectively lower the CPU voltage and core frequency to decrease average power consumption and heat production. Auto lets the BIOS automatically configure this setting. (Default: Auto)

& ExtremeMemoryProfile(X.M.P.)(Note 2) Allows the BIOS to read the SPD data on XMP memory module(s) to enhance memory performance when

enabled. Disabled Disables this function. (Default) Profile1 Uses Profile 1 settings. Profile2 (Note 2) Uses Profile 2 settings.

& System Memory Multiplier Allows you to set the system memory multiplier. Auto sets memory multiplier according to memory SPD

data. (Default: Auto) & MemoryFrequency(MHz)

The first memory frequency value is the normal operating frequency of the memory being used; the second is the memory frequency that is automatically adjusted according to the System Memory Multiplier settings.

(Note 1) This item is present only when you install a CPU that supports this feature. For more information about Intel CPUs' unique features, please visit Intel's website.

(Note 2) This item is present only when you install a CPU and a memory module that support this feature.

` Advanced Memory Settings & ExtremeMemoryProfile(X.M.P.)(Note 2),SystemMemoryMultiplier,MemoryFrequency(MHz)

The settings above are synchronous to those under the same items on the Advanced Frequency Settings menu. & MemoryOverclockingProfiles (Note) j

Allows you to set the memory frequency. Options may vary depending on the memory being used. (Default: Disabled)


- 22 -

` PC Health Status & ResetCaseOpenStatus

Disabled Keeps or clears the record of previous chassis intrusion status. (Default) Enabled Clears the record of previous chassis intrusion status and the CaseOpen field will

show "No" at next boot. & CaseOpen

Displays the detection status of the chassis intrusion detection device attached to the motherboard CI header. If the system chassis cover is removed, this field will show "Yes", otherwise it will show "No". To clear the chassis intrusion status record, set ResetCaseOpenStatus to Enabled, save the settings to the CMOS, and then restart your system.

& CPU Vcore/CPU VRIN/Dram Voltage/+3.3V/+5V/+12V/CPU VAXG Displays the current system voltages.

& CPU/System Temperature Displays current CPU/system temperature.

` Channel A/B Memory Sub TimingsThis sub-menu provides memory timing settings for each channel of memory. This sub-menu provides memory timing settings for each channel of memory. The respective timing setting screens are configurable only when Memory Timing Mode is set to Manual or Advanced Manual. Note: Your system may become unstable or fail to boot after you make changes on the memory timings. If this occurs, please reset the board to default values by loading optimized defaults or clearing the CMOS values.

` Advanced Voltage SettingsThis sub-menu allows you to set CPU, chipset and memory voltages.

& Memory Boot Mode Provides memory detection and training methods.

Auto Lets the BIOS automatically configure this setting. (Default) Enable Fast Boot Skip memory detection and training in some specific criteria for faster memory

boot. Disable Fast Boot Detect and train memory at every single boot.

& Memory Enhancement Settings Provides three different memory performance enhancement settings: Normal (basic performance), Enhanced

Stability, and Enhanced Performance. (Default: Normal) & Memory Timing Mode

Manual and Advanced Manual allows the Channel Interleaving, Rank Interleaving, and memory timing settings below to be configurable. Options are: Auto (default), Manual, Advanced Manual.

& ProfileDDRVoltage When using a non-XMP memory module or ExtremeMemoryProfile(X.M.P.) is set to Disabled, the

value is displayed according to your memory specification. When Extreme Memory Profile (X.M.P.) is set to Profile1 or Profile2, the value is displayed according to the SPD data on the XMP memory.

& Channel Interleaving Enables or disables memory channel interleaving. Enabled allows the system to simultaneously access

different channels of the memory to increase memory performance and stability. Auto lets the BIOS automatically configure this setting. (Default: Auto)

& Rank Interleaving Enables or disables memory rank interleaving. Enabled allows the system to simultaneously access different

ranks of the memory to increase memory performance and stability. Auto lets the BIOS automatically configure this setting. (Default: Auto)

- 23 -

& CPU/System Fan Speed Displays current CPU/system fan speeds.

& CPU/System Temperature Warning Sets the warning threshold for CPU/system temperature. When temperature exceeds the threshold, BIOS

will emit warning sound. Options are: Disabled (default), 60oC/140oF, 70oC/158oF, 80oC/176oF, 90oC/194oF. & CPU/System Fan Fail Warning

Allows the system to emit warning sound if the fan is not connected or fails. Check the fan condition or fan connection when this occurs. (Default: Disabled)

& CPU Fan Speed Control (CPU_FAN Connector) Allows you to determine whether to enable the fan speed control function and adjust the fan speed.

Normal Allows the fan to run at different speeds according to the CPU temperature. You can adjust the fan speed with EasyTune based on your system requirements. (Default)

Silent Allows the fan to run at slow speeds. Manual Allows you to control the fan speed under the Fan Speed Percentage item. Full Speed Allows the fan to run at full speeds.

& Fan Speed Percentage Allows you to control the fan speed. This item is configurable only when CPU Fan Speed Control is set

to Manual. Options are: 0.75 PWM value /oC ~ 2.50 PWM value /oC. & 1st System Fan Speed Control (SYS_FAN1 Connector)

Allows you to determine whether to enable the fan speed control function and adjust the fan speed. Normal Allows the fan to run at different speeds according to the system temperature. You can

adjust the fan speed with EasyTune based on your system requirements. (Default) Silent Allows the fan to run at slow speeds. Manual Allows you to control the fan speed under the Fan Speed Percentage item. Full Speed Allows the fan to run at full speeds.

& Fan Speed Percentage Allows you to control the fan speed. This item is configurable only when 1st System Fan Speed Control

is set to Manual. Options are: 0.75 PWM value /oC ~ 2.50 PWM value /oC. & 2nd System Fan Speed Control (SYS_FAN2 Connector)



& Fan Speed Percentage Allows you to control the fan speed. This item is configurable only when 2nd System Fan Speed Control

is set to Manual. Options are: 0.75 PWM value /oC ~ 2.50 PWM value /oC. & 3rd System Fan Speed Control (SYS_FAN3 Connector)



& Fan Speed Percentage Allows you to control the fan speed. This item is configurable only when 3rd System Fan Speed Control

is set to Manual. Options are: 0.75 PWM value /oC ~ 2.50 PWM value /oC.

- 24 -

2-3 System Information

This section provides information on your motherboard model and BIOS version. You can also select the default language used by the BIOS and manually set the system time.

& System Language Selects the default language used by the BIOS.

& System Date Sets the system date. The date format is week (read-only), month, date, and year. Use to switch

between the Month, Date, and Year fields and use the or key to set the desired value.

& System Time Sets the system time. The time format is hour, minute, and second. For example, 1 p.m. is 13:0:0. Use

to switch between the Hour, Minute, and Second fields and use the or key to set the desired value.

& Access Level Displays the current access level depending on the type of password protection used. (If no password is

set, the default will display as Administrator.) The Administrator level allows you to make changes to all BIOS settings; the User level only allows you to make changes to certain BIOS settings but not all.

` Miscellaneous Settings & PCIeSlotConfiguration

Allows you to set the operation mode of the PCI Express slots to Gen 1, Gen 2, or Gen 3. Actual operation mode is subject to the hardware specification of each slot. Auto lets the BIOS automatically configure this setting. (Default: Auto)

& DMI Gen2 Speed Allows you to configure the DMI link speed.

Auto Lets the BIOS automatically configure this setting. Enabled Sets the DMI link speed to Gen 2. (Default) Disabled Sets the DMI link speed to Gen 1.

& 3DMark01 Boost Allows you to determine whether to enhance some legacy benchmark performance. (Default: Disabled)

- 25 -

2-4 BIOSFeatures

& BootOptionPriorities Specifies the overall boot order from the available devices. Removable storage devices that support GPT format will be prefixed with "UEFI:" string on the boot device

list. To boot from an operating system that supports GPT partitioning, select the device prefixed with "UEFI:" string.

Or if you want to install an operating system that supports GPT partitioning such as Windows 7 64-bit, select the optical drive that contains the Windows 7 64-bit installation disk and is prefixed with "UEFI:" string.

& Bootup NumLock State Enables or disables Numlock feature on the numeric keypad of the keyboard after the POST. (Default:

Enabled) & SecurityOption

Specifies whether a password is required every time the system boots, or only when you enter BIOS Setup. After configuring this item, set the password(s) under the Administrator Password/User Password item.

Setup A password is only required for entering the BIOS Setup program. System A password is required for booting the system and for entering the BIOS Setup program.

(Default) & FullScreenLOGOShow

Allows you to determine whether to display the GIGABYTE Logo at system startup. Disabled skips the GIGABYTE Logo when the system starts up. (Default: Enabled)

& Fast Boot Enables or disables Fast Boot to shorten the OS boot process. Ultra Fast provides the fastest bootup

speed. (Default: Disabled) & VGA Support

Allows you to select which type of operating system to boot. Auto Enables legacy option ROM only. EFI Driver Enables EFI option ROM. (Default)

This item is configurable only when Fast Boot is set to Enabled or Ultra Fast.

- 26 -

& USB Support Disabled All USB devices are disabled before the OS boot process completes. Full Initial All USB devices are functional in the operating system and during the POST. Partial Initial Part of the USB devices are disabled before the OS boot process completes. (Default)

This item is configurable only when Fast Boot is set to Enabled. This item is disabled when Fast Boot is set to Ultra Fast.

& PS2 Devices Support Disabled All PS/2 devices are disabled before the OS boot process completes. Enabled All PS/2 devices are functional in the operating system and during the POST. (Default)

This item is configurable only when Fast Boot is set to Enabled. This item is disabled when Fast Boot is set to Ultra Fast.

& NetWork Stack Driver Support Disabled Disables booting from the network. (Default) Enabled Enables booting from the network.

This item is configurable only when Fast Boot is set to Enabled or Ultra Fast. & Next Boot After AC Power Loss

Normal Boot Enables normal bootup upon the return of the AC power. (Default) Fast Boot Keeps the Fast Boot settings upon the return of the AC power.

This item is configurable only when Fast Boot is set to Enabled or Ultra Fast. & Limit CPUID Maximum (Note)

Allows you to determine whether to limit CPUID maximum value. Set this item to Disabled for Windows XP operating system; set this item to Enabled for legacy operating system such as Windows NT4.0. (Default: Disabled)

& Execute Disable Bit (Note) Enables or disables Intel Execute Disable Bit function. This function may enhance protection for the

computer, reducing exposure to viruses and malicious buffer overflow attacks when working with its supporting software and system. (Default: Enabled)

& IntelVirtualizationTechnology(Note) Enables or disables Intel Virtualization Technology. Virtualization enhanced by Intel Virtualization

Technology will allow a platform to run multiple operating systems and applications in independent partitions. With virtualization, one computer system can function as multiple virtual systems. (Default: Enabled)

& Intel TXT(LT) Support (Note) Enables or disables Intel Trusted Execution Technology (Intel TXT). Intel Trusted Execution Technology

provides a hardware-based security foundation. (Default: Disabled) & Dynamic Storage Accelerator

Enables or disables Intel Dynamic Storage Accelerator. When enabled, the hard drive I/O performance will be adjusted according to hard drive load. (Default: Disabled)

& VT-d (Note) Enables or disables Intel Virtualization Technology for Directed I/O. (Default: Enabled)

& Windows 8 Features Allows you to select the operating system to be installed. (Default: Other OS)

& CSM Support Enables or disables UEFI CSM (Compatibility Support Module) to support a legacy PC boot process.

Always Enables UEFI CSM. (Default) Never Disables UEFI CSM and supports UEFI BIOS boot process only.

This item is configurable only when Windows 8 Features is set to Windows 8.


- 27 -

& Boot Mode Selection Allows you to select which type of operating system to boot.

UEFI and Legacy Allows booting from operating systems that support legacy option ROM or UEFI option ROM. (Default)

Legacy Only Allows booting from operating systems that only support legacy Option ROM. UEFI Only Allows booting from operating systems that only support UEFI Option ROM.

This item is configurable only when CSM Support is set to Always. & LANPXEBootOptionROM

Allows you to select whether to enable the legacy option ROM for the LAN controller. (Default: Disabled) This item is configurable only when CSM Support is set to Always.

& StorageBootOptionControl Allows you to select whether to enable the UEFI or legacy option ROM for the storage device controller.

Disabled Disables option ROM. Legacy only Enables legacy option ROM only. (Default) UEFI only Enables UEFI option ROM only. Legacy First Enables legacy option ROM first. UEFI First Enables UEFI option ROM first.

This item is configurable only when CSM Support is set to Always. & OtherPCIDeviceROMPriority

Allows you to select whether to enable the UEFI or Legacy option ROM for the PCI device controller other than the LAN, storage device, and graphics controllers.

Legacy OpROM Enables legacy option ROM only. UEFI OpROM Enables UEFI option ROM only. (Default)

This item is configurable only when CSM Support is set to Always. & Network stack

Disables or enables booting from the network to install a GPT format OS, such as installing the OS from the Windows Deployment Services server. (Default: Disabled)

& Ipv4 PXE Support Enables or disables IPv4 PXE Support. This item is configurable only when Network stack is enabled.

& Ipv6 PXE Support Enables or disables IPv6 PXE Support. This item is configurable only when Network stack is enabled.

& Administrator Password Allows you to configure an administrator password. Press on this item, type the password, and

then press . You will be requested to confirm the password. Type the password again and press . You must enter the administrator password (or user password) at system startup and when entering BIOS Setup. Differing from the user password, the administrator password allows you to make changes to all BIOS settings.

& User Password Allows you to configure a user password. Press on this item, type the password, and then press

. You will be requested to confirm the password. Type the password again and press . You must enter the administrator password (or user password) at system startup and when entering BIOS Setup. However, the user password only allows you to make changes to certain BIOS settings but not all.

To cancel the password, press on the password item and when requested for the password, enter the correct one first. When prompted for a new password, press without entering any password. Press again when prompted to confirm.

- 28 -

& InitialDisplayOutput Specifies the first initiation of the monitor display from the installed PCI graphics card, PCI Express graphics

card or the onboard graphics. IGFX Sets the onboard graphics as the first display. PCIe 1 Slot Sets the graphics card on the PCIEX16 slot as the first display. (Default) PCIe 2 Slot Sets the graphics card on the PCIEX4 slot as the first display. PCI Sets the graphics card on the PCI slot as the first display.

& XHCI Mode Allows you to determine the operating mode for the xHCI controller in OS.

Smart Auto This mode is available only when the BIOS supports the xHCI controller in the pre-boot environment. This mode is similar to Auto, but it adds the capability to route the ports to xHCI or EHCI according to setting used in previous boots (for non-G3 boot) in the pre-boot environment. This allows the use of USB 3.0 devices prior to OS boot. xHCI controller enabling and rerouting should follow the steps in Auto, when previous boot routs ports to EHCI. Note: This is the recommended mode when BIOS has xHCI pre-boot support. (Default)

Auto BIOS routes the sharable ports to EHCI controller. Then it uses ACPI protocols to provide an option to enable the xHCI controller and reroute the sharable ports. Note: This is the recommended mode when BIOS does NOT have xHCI pre-boot support.

Enabled All shared ports are eventually routed to the xHCI controller during the BIOS boot process. If BIOS does not have pre-boot support for the xHCI controller, it should initially route the sharable ports to the EHCI controller and then prior to OS boot it should route the ports to xHCI controller. Note: OS has to provide support for the xHCI controller in this mode. If the OS does not provide support, all sharable ports won't work.

Disabled The USB 3.0 ports are routed to the EHCI controller and the xHCI controller is turned off. All USB 3.0 devices function as High Speed devices regardless of xHCI software support/availability.

& Audio Controller Enables or disables the onboard audio function. (Default: Enabled) If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to

Disabled.

2-5 Peripherals

- 29 -

& Intel Processor Graphics Enables or disables the onboard graphics function. (Default: Enabled)

& Intel Processor Graphics Memory Allocation Allows you to set the onboard graphics memory size. Options are: 32M~1024M. (Default: 64M)

& DVMTTotalMemorySize Allows you to allocate the DVMT memory size of the onboard graphics. Options are: 128M, 256M, MAX.

(Default: MAX)

& Intel(R) Rapid Start Technology Enables or disables Intel Rapid Start Technology. (Default: Disabled)

& Legacy USB Support Allows USB keyboard/mouse to be used in MS-DOS. (Default: Enabled)

& XHCI Hand-off Determines whether to enable XHCI Hand-off feature for an operating system without XHCI Hand-off

support. (Default: Enabled) & EHCI Hand-off

Determines whether to enable EHCI Hand-off feature for an operating system without EHCI Hand-off support. (Default: Disabled)

& USB Storage Devices Displays a list of connected USB mass storage devices. This item appears only when a USB storage device

is installed. & Two Layer KVM Switch

Set to Enabled to ensure proper device functionality when chaining two KVM switches. (Default: Disabled) & OnBoardLANController

Enables or disables the onboard LAN function. (Default: Enabled) If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to

Disabled.

` SATAConfiguration & Integrated SATA Controller

Enables or disables the integrated SATA controllers. (Default: Enabled) & SATA Mode Selection

Enables or disables RAID for the SATA controllers integrated in the Chipset or configures the SATA controllers to AHCI mode.

IDE Configures the SATA controller to IDE mode. RAID Enables RAID for the SATA controller. AHCI Configures the SATA controllers to AHCI mode. Advanced Host Controller Interface (AHCI)

is an interface specification that allows the storage driver to enable advanced Serial ATA features such as Native Command Queuing and hot plug. (Default)

` Serial ATA Port 0/1/2/3/4/5 & Port 0/1/2/3/4/5

Enables or disables each SATA port. (Default: Enabled) & Hot plug

Enables or disable the hot plug capability for each SATA port. (Default: Disabled) & External SATA

Enables or disables support for external SATA devices. (Default: Disabled)

- 30 -

` SuperIOConfiguration This section provides information on the super I/O chip and allows you to configure the serial port and

parallel port. & Serial Port A

Enables or disables the onboard serial port. (Default: Enabled) & Parallel Port

Enables or disables the onboard parallel port. (Default: Enabled) ` Device Mode

This item is configurable only when Parallel Port is set to Enabled. Selects an operating mode for the onboard parallel (LPT) port. Options are: Standard Parallel Port Mode (Default), EPP Mode (Enhanced Parallel Port), ECP Mode (Extended Capabilities Port), EPP Mode & ECP Mode.

` Intel(R) Smart Connect Technology & ISCT Support

Enables or disables Intel Smart Connect Technology. (Default: Disabled) ` Realtek PCIe GBE Family Controller

This sub-menu provides information on LAN configuration.

2-6 Power Management

& Power Loading Enables or disables dummy load. When the power supply is at low load, a self-protection will activate causing

it to shutdown or fail. If this occurs, please set to Enabled. Auto lets the BIOS automatically configure this setting. (Default: Auto)

& Resume by Alarm Determines whether to power on the system at a desired time. (Default: Disabled) If enabled, set the date and time as following:

Wake up day: Turn on the system at a specific time on each day or on a specific day in a month. Wake up hour/minute/second: Set the time at which the system will be powered on automatically.

Note: When using this function, avoid inadequate shutdown from the operating system or removal of the AC power, or the settings may not be effective.

- 31 -

& Soft-OffbyPWR-BTTN Configures the way to turn off the computer in MS-DOS mode using the power button.

Instant-Off Press the power button and then the system will be turned off instantly. (Default) Delay 4 Sec. Press and hold the power button for 4 seconds to turn off the system. If the power

button is pressed for less than 4 seconds, the system will enter suspend mode. & RC6(Render Standby)

Allows you to determine whether to let the onboard graphics enter standby mode to decrease power consumption. (Default: Enabled)

& AC BACK Determines the state of the system after the return of power from an AC power loss.

Memory The system returns to its last known awake state upon the return of the AC power. Always On The system is turned on upon the return of the AC power. Always Off The system stays off upon the return of the AC power. (Default)

& PowerOnByKeyboard Allows the system to be turned on by a PS/2 keyboard wake-up event. Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.

Disabled Disables this function. (Default) Password Set a password with 1~5 characters to turn on the system. Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system. Any Key Press any key to turn on the system.

& PowerOnPassword Set the password when PowerOnByKeyboard is set to Password. Press on this item and set a password with up to 5 characters and then press to accept.

To turn on the system, enter the password and press . Note: To cancel the password, press on this item. When prompted for the password, press

again without entering the password to clear the password settings. & PowerOnByMouse

Allows the system to be turned on by a PS/2 mouse wake-up event. Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.

Disabled Disables this function. (Default) Move Move the mouse to turn on the system. Double Click Double click on left button on the mouse to turn on the system.

& ErP Determines whether to let the system consume least power in S5 (shutdown) state. (Default: Disabled) Note: When this item is set to Enabled, the following functions will become unavailable: PME event wake

up, power on by mouse, power on by keyboard, and wake on LAN.

& Platform Power Management Enables or disables the Active State Power Management function (ASPM). (Default: Disabled)

& PEG ASPM Allows you to configure the ASPM mode for the device connected to the CPU PEG bus. Auto lets the BIOS

automatically configure this setting. This item is configurable only when Platform Power Management is set to Enabled. (Default: Auto)

& PCIe ASPM Allows you to configure the ASPM mode for the device connected to Chipset's PCI Express bus. Auto

lets the BIOS automatically configure this setting. This item is configurable only when Platform Power Management is set to Enabled. (Default: Auto)

& CPU DMI Link ASPM Control Allows you to configure the ASPM mode for the CPU side of the DMI link. Auto lets the BIOS automatically

configure this setting. This item is configurable only when Platform Power Management is set to Enabled. (Default: L0sL1)

- 32 -

& Save & Exit Setup Press on this item and select Yes. This saves the changes to the CMOS and exits the BIOS Setup

program. Select No or press to return to the BIOS Setup Main Menu. & Exit Without Saving

Press on this item and select Yes. This exits the BIOS Setup without saving the changes made in BIOS Setup to the CMOS. Select No or press to return to the BIOS Setup Main Menu.

& LoadOptimizedDefaults Press on this item and select Yes to load the optimal BIOS default settings. The BIOS defaults

settings help the system to operate in optimum state. Always load the Optimized defaults after updating the BIOS or after clearing the CMOS values.

& BootOverride Allows you to select a device to boot immediately. Press on the device you select and select Yes

to confirm. Your system will restart automatically and boot from that device. & SaveProfiles

This function allows you to save the current BIOS settings to a profile. You can create up to 8 profiles and save as Setup Profile 1~ Setup Profile 8. Press to complete. Or you can select Select File in HDD/USB/FDD to save the profile to your storage device.

& LoadProfiles If your system becomes unstable and you have loaded the BIOS default settings, you can use this function

to load the BIOS settings from a profile created before, without the hassles of reconfiguring the BIOS settings. First select the profile you wish to load and then press to complete. You can select Select File in HDD/USB/FDD to input the profile previously created from your storage device or load the profile automatically created by the BIOS, such as reverting the BIOS settings to the last settings that worked properly (last known good record).

2-7 Save & Exit

& PCH DMI Link ASPM Control Allows you to configure the ASPM mode for both CPU side and Chipset side of the DMI link. Auto lets the

BIOS automatically configure this setting. This item is configurable only when Platform Power Management is set to Enabled. (Default: Enabled)

- 33 -

Chapter 3 Appendix

Before you begin At least two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard drives with identical model and capacity). If you do not want to create RAID, you may prepare only one hard drive.

Windows setup disk. Motherboard driver disk. A USB flash drive.

ConfiguringtheOnboardSATAControllerA. Installing SATA hard drive(s) in your computerAttach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port on the motherboard. Then connect the power connector from your power supply to the hard drive.

B.ConfiguringSATAcontrollermodeinBIOSSetupMake sure to configure the SATA controller mode correctly in system BIOS Setup. For the BIOS Setup menus, refer to Chapter 2, "BIOS Setup," "Integrated Peripherals."Steps:1. Turn on your computer and press to enter BIOS Setup during the POST (Power-On Self-Test). Go

to Peripherals\SATAConfiguration, make sure Integrated SATA Controller is enabled. To create RAID, set SATA Mode Selection to RAID (Figure 1). If you do not want to create RAID, set this item to IDE or AHCI.

2. If you want to configure UEFI RAID, follow the steps in "C-1." To enter the legacy RAID ROM, save the settings and exit BIOS Setup. Refer to "C-2" for more information.

The BIOS Setup menus described in this section may differ from the exact settings for your motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version.

C-1.UEFIRAIDConfigurationOnly Windows 8.1/8 64-bit supports UEFI RAID configuration.Steps:1. After you set the SATA controller to RAID mode, go to BIOSFeatures and set Windows 8 Features to

Windows 8 and CSM Support to Never. Save the changes and exit BIOS Setup.2. After the system reboot, enter BIOS Setup again. Then enter the Peripherals\Intel(R) Rapid Storage

Technology sub-menu.3. On the Intel(R) Rapid Storage Technology menu, press on Create RAID Volume to enter the

Create RAID Volume screen. Enter a volume name with 1~16 letters (letters cannot be special characters) under the Name item and press . Then, select a RAID level. RAID levels supported include RAID 0, RAID 1, Recovery, RAID 10, and RAID 5 (the selections available depend on the number of the hard drives being installed). Next, use the down arrow key to move to Select Disks.

4. Under Select Disks item, select the hard drives to be included in the RAID array. Press the key on the hard drives to be selected (selected hard drives are marked with "X"). Then set the stripe block size. The stripe block size can be set from 4 KB to 128 KB. Once you have selected the stripe block size, set the volume capacity.

5. After setting the capacity, move to Create Volume and press to begin6. After completing, you'll be brought back to the Intel(R) Rapid Storage Technology screen. Under RAID

Volumes you can see the new RAID volume. To see more detailed information, press on the volume to check for information on RAID level, stripe block size, array name, and array capacity, etc.

3-1 ConfiguringSATAHardDrive(s)

- 34 -

C-2.ConfiguringLegacyRAIDROMEnter the Intel legacy RAID BIOS setup utility to configure a RAID array. Skip this step and proceed with the installation of Windows operating system for a non-RAID configuration.Steps:1. After the POST memory test begins and before the operating system boot begins, look for a message which

says "Press to enter Configuration Utility". Press + to enter the RAID Configuration Utility.2. After you press + , the MAIN MENU screen will appear. If you want to create a RAID array, select

Create RAID Volume in MAIN MENU and press .3. After entering the CREATEVOLUMEMENU screen, enter a volume name with 1~16 letters (letters cannot

be special characters) under the Name item and press . Then, select a RAID level. RAID levels supported include RAID 0, RAID 1, Recovery, RAID 10, and RAID 5 (the selections available depend on the number of the hard drives being installed). Press to proceed.

4. Under Disks item, select the hard drives to be included in the RAID array. If only two hard drives are installed, they will be automatically assigned to the array. Set the stripe block size if necessary. The stripe block size can be set from 4 KB to 128 KB. Once you have selected the stripe block size, press .

5. Enter the array capacity and press . Finally press on the Create Volume item to begin creating the RAID array. When prompted to confirm whether to create this volume, press to confirm or to cancel.

6. When completed, you can see detailed information about the RAID array in the DISK/VOLUMEINFORMATION section, including the RAID level, stripe block size, array name, and array capacity, etc. To exit the RAID BIOS utility, press or select 6. Exit in MAIN MENU.

InstallingtheSATARAID/AHCIDriverandOperatingSystemWith the correct BIOS settings, you are ready to install the operating system.

InstallingtheOperatingSystemAs Windows 7 already include Intel SATA RAID/AHCI driver, you do not need to install separate RAID/AHCI driver during the Windows installation process. After the operating system is installed, we recommend that you install all required drivers from the motherboard driver disk using "Xpress Install" to ensure system performance and compatibility. To install Windows 8.1/8, refer to the steps below: Steps:1. Copy the IRST folder under BootDrv in the driver disk to your USB thumb drive.2. Boot from the Windows 8.1/8 setup disk and perform standard OS installation steps. When the screen

requesting you to load the driver appears, select Browse.3. Insert the USB thumb drive and then browse to the location of the driver. The locations of the drivers are

as follows: Windows 32-bit: \iRST\32Bit Windows 64-bit: \iRST\64Bit

4. When a screen as shown, select Intel(R) Desktop/Workstation/Server Express Chipset SATA RAID Controller and click Next to load the driver and continue the OS installation.

- 35 -

Before installing the drivers, first install the operating system. (The following instructions use Windows 8.1 as the example operating system.)

After installing the operating system, insert the motherboard driver disk into your optical drive. Click on the message "Tap to choose what happens with this disc" on the top-right corner of the screen and select "Run Run.exe." (Or go to My Computer, double-click the optical drive and execute the Run.exe program.)

3-2 Drivers Installation

"Xpress Install" will automatically scan your system and then list all of the drivers that are recommended to install. You can click the Xpress Install button and "Xpress Install" will install all of the selected drivers. Or click the arrow icon to individually install the drivers you need.

For more software information, please visit GIGABYTE's website.

- 36 -

Regulatory Statements

Regulatory NoticesThis document must not be copied without our written permission, and the contents there of must not be imparted to a third party nor be used for any unauthorized purpose.Contravention will be prosecuted. We believe that the information contained herein was accurate in all respects at the time of printing. GIGABYTE cannot, however, assume any responsibility for errors or omissions in this text. Also note that the information in this document is subject to change without notice and should not be construed as a commitment by GIGABYTE.

OurCommitmenttoPreservingtheEnvironmentIn addition to high-efficiency performance, all GIGABYTE motherboards fulfill European Union regulations for RoHS (Restriction of Certain Hazardous Substances in Electrical and Electronic Equipment) and WEEE (Waste Electrical and Electronic Equipment) environmental directives, as well as most major worldwide safety requirements. To prevent releases of harmful substances into the environment and to maximize the use of our natural resources, GIGABYTE provides the following information on how you can responsibly recycle or reuse most of the materials in your "end of life" product.

RestrictionofHazardousSubstances(RoHS)DirectiveStatementGIGABYTE products have not intended to add and safe from hazardous substances (Cd, Pb, Hg, Cr+6, PBDE and PBB). The parts and components have been carefully selected to meet RoHS requirement. Moreover, we at GIGABYTE are continuing our efforts to develop products that do not use internationally banned toxic chemicals.

Waste Electrical & Electronic Equipment (WEEE) Directive StatementGIGABYTE will fulfill the national laws as interpreted from the 2002/96/EC WEEE (Waste Electrical and Electronic Equipment) directive. The WEEE Directive specifies the treatment, collection, recycling and disposal of electric and electronic devices and their components. Under the Directive, used equipment must be marked, collected separately, and disposed of properly.

WEEE Symbol StatementThe symbol shown below is on the product or on its packaging, which indicates that this product must not be disposed of with other waste. Instead, the device should be taken to the waste collection centers for activation of the treatment, collection, recycling and disposal procedure. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.

For more information about where you can drop off your waste equipment for recycling, please contact your local government office, your household waste disposal service or where you purchased the product for details of environmentally safe recycling.

When your electrical or electronic equipment is no longer useful to you, "take it back" to your local or regional waste collection administration for recycling.

If you need further assistance in recycling, reusing in your "end of life" product, you may contact us at the Customer Care number listed in your product's user's manual and we will be glad to help you with your effort.

Finally, we suggest that you practice other environmentally friendly actions by understanding and using the energy-saving features of this product (where applicable), recycling the inner and outer packaging (including shipping containers) this product was delivered in, and by disposing of or recycling used batteries properly. With your help, we can reduce the amount of natural resources needed to produce electrical and electronic equipment, minimize the use of landfills for the disposal of "end of life" products, and generally improve our quality of life by ensuring that potentially hazardous substances are not released into the environment and are disposed of properly.

- 37 -

FCCNotice(U.S.A.Only)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult a dealer or experienced TV/radio technician for help.

Canada, Industry Canada (IC) Notices / Canada, avis d'Industry Canada (IC) This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this

device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numrique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer

d'interfrence et (2) cet appareil doit accepter toute interfrence, notamment les interfrences qui peuvent affecter son fonctionnement.

- 38 -

- 39 -

- 40 -

Contact Us

GIGA-BYTETECHNOLOGYCO.,LTD.Address: No.6, Bao Chiang Road, Hsin-Tien Dist., New Taipei City 231,TaiwanTEL: +886-2-8912-4000, FAX: +886-2-8912-4005Tech. and Non-Tech. Support (Sales/Marketing) : http://ggts.gigabyte.com.twWEB address (English): http://www.gigabyte.comWEB address (Chinese): http://www.gigabyte.tw

You may go to the GIGABYTE website, select your language in the language list on the top right corner of the website.

GIGABYTE Global Service System

To submit a technical or non-technical (Sales/Marketing) question, please link to:http://ggts.gigabyte.com.twThen select your language to enter the system.

GA-Z97M-D3H/GA-H97M-D3H Motherboard LayoutGA-Z97M-D3H/GA-H97M-D3H Motherboard Block DiagramChapter 1Hardware Installation1-1Installation Precautions1-2Product Specifications1-3Installing the CPU1-4Installing the Memory1-5Installing an Expansion Card1-6Back Panel Connectors1-7Internal Connectors

Chapter 2BIOS Setup2-1Startup Screen2-2M.I.T.2-3System Information2-4BIOS Features2-5Peripherals2-6Power Management2-7Save & Exit

Chapter 3Appendix3-1Configuring SATA Hard Drive(s)3-2Drivers InstallationRegulatory StatementsContact Us

ga h97m d3h (ga z97m d3h) english

Documents

motherboard bios

h97md3h motherboard

d3h gah97m

d motherboard block

product specifications

bios features

productrelated information

technical information