garden trellis/steel arch - harbor freight...

SKU 99842 For technical questions, please call 1-800-444-3353.

InstructIons and precautIons

distributed exclusively by Harbor Freight tools®.3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

saVe tHese InstructIons. read all precautIons and InstructIons.

Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this document or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this document may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Garden trellIs/steel arcH99842


specIFIcatIons

Frame Steel TubeHardware Low Carbon Steel

unpackInGWhen unpacking, check to make sure that

the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this document as soon as possible.

Important saFetY InFormatIon

assembly precautionsAssemble only according to these in-1. structions. Improper assembly can cre-ate hazards.Wear ANSI-approved safety goggles and 2. heavy-duty work gloves during assembly.Keep assembly area clean and well lit.3. Keep bystanders out of the area during 4. assembly.Do not assemble when tired or when un-5. der the influence of drugs or medication.

use precautionsThis product is not a toy. Do not allow 1. children to play with or near this item.Use for intended purpose(s) only.2. Inspect before use; do not use if parts 3. are loose or damaged.Maintain product labels and nameplates. 4. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.Assem-bly Instructions

read the entIre Important saFetY InFormatIon section at the beginning of this document including all text under subheadings therein before set up or use of this product.

assembly

assemble the arch

Locate the two Arch Halves (1). 1. Locate the three Arch Crosspieces (3).2. Locate the six M6-15 Screws (8).3. Attach a Crosspiece (3) to an Arch 4. Half (1) with one of the supplied M6-15 screws (8) using the supplied L-Shaped hex wrench (10).Repeat this with the other two Cross-5. pieces.Position the second Arch Half (1) against 6. the free ends of the Crosspieces (3) and attach it to the Crosspieces with the remaining M6-15 Screws (8).

Fig. 1

Arch HalfCrosspiece

7. The top arch sub-assembly is now com-plete and ready to be attached to the Arch Sides (2). (See Fig. 1.)With a helper holding one of the sides 8. upright, bring the Arch down onto it, slip-ping the ends of both right and left Arch tubings over the smaller diameter tops of the Arch Side tubes. Be sure the spring-loaded pins snap 9. through the corresponding holes in the Arch tube ends.


Fig. 2

10. Repeat this process with the other Arch Side (2) as well. One of the tubes, at each end of the Arch 11. Side has a built-in spring-loaded pin that goes through a corresponding hole in the Arch tube sliding down over it. This locks the Arch sub-assembly to the Arch Side (2). With both Arch Sides (2) attached, locate 12. the Bases (4). These Bases have a short, small diam-13. eter tube attached to each end of the Base. Each short tube has a built-in spring-a. loaded pin just as the Arch Sides (2) have.

Slip the bottoms of the Arch Side tubes 14. over the short small diameter tube on the bases making sure that all of the

four spring-loaded pins go through their respective holes.

Fig. 3

Arch Base

15. The Arch is now ready for the gates which will hang and swing on built-in hinges.Find the right-hand Gate (6), 16. Located on the right-hand edge will be 17. the gate’s hinge (two mounted pegs pointing downward).These two pegs are to fit into two metal 18. loops (the Arch part of the hinge) at-tached to the inside of the front of the Arch assembly. Slide the pegs into the loops forming the 19. hinges. This gate will have a loop at-tached to it on the left-hand side at the


top horizontal crossbar as part of the lock mechanism. Take the left-hand Gate with Sliding Bar 20. Lock and insert its pegs (located on its left-hand side) into the metal loops on the inside of the left-hand Arch Side.

Fig. 4

21. The gates will now open and close swinging on their hinges allowing access through the Arch. The Sliding Latch on the left-hand gate slides to the right and into the metal loop on the right-hand gate keeping the gates closed.Gate Top Caps (9) ball-shaped parts are 22. fit over the gate’s vertical tubes on either side of each gate.

Assuming the Garden Trellis/Steel Arch 23. is to be located on lawn or dirt sur-face, the four supplied L-Stakes can be pushed through the holes at the ends of the Base, and driven into the ground.

parts lIst & assemblY dIaGram

part description Qty.1 Arch Half 22 Arch Side 23 Arch Crosspiece 34 Base 25 Gate with Sliding Latch 16 Gate 17 Stakes, Low carbon, zinc plated 48 M6-15 Screws 69 Gate top caps 4

10 L-Style steel hex wrench, zinc plated (not shown) 1


Base 4

Gate with Latch 5

Gate 6

L-Shaped Stakes7

M6-15 Screws 8

record serial number Here: note: If product has no serial number, record month and year of purchase instead.note: Some parts are listed and shown for illustration purposes only, and are not available individually as

replacement parts.

please read tHe FolloWInG careFullYTHE MANUFACTURER AND/OR DISTRIBUTOR HAS PROvIDED THE PARTS LIST AND ASSEMBLy DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANy REPRESENTATION OR WARRANTy OF ANy KIND TO THE BUyER THAT HE OR SHE IS qUALIFIED TO MAKE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLy STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN By CERTIFIED AND LICENSED TECHNICIANS, AND NOT By THE BUyER. THE BUyER ASSUMES ALL RISK AND LIABILITy ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Arch Half 1

Arch Side 2

Arch Crosspiece 3

Gate Top Caps 9

Gate Top Caps 9

garden trellis/steel arch - harbor freight...

Documents