gas/light-oil dual burners - schede tecniche · 2017. 1. 3. · g20 g25 g31 g30 max. pressure mbar...
TRANSCRIPT
420010602300
21.11.2014
Multicalor TS 100 AB/AB Multicalor TS 140 AB/AB
GAS/LIGHT-OIL DUAL BURNERS
pag.2
420010602300 Multicalor TS 100-140 AB/AB
Multicalor 100 140Max. Thermal Output kW 1000 1300
kcal/h 860.000 1.118.000Min. Thermal Output kW 300 400
kcal/h 258.000 344.000
FUEL CHARACTERISTICSModel : Multicalor TS 100-140 AB/AB Gas family
G20 G25 G31 G30Max. pressure mbar 25 - 45 -Min. pressure mbar 17 - 25 -Gas Low Heat Value: kcal/Nm3 8.570 - 22.260 -Light-oil Low Heat Value 10.200 kcal/Kg max 1,5° E a 20° C
TECHNICAL FEATURES
OVERALL DIMENSIONS
MODEL A B C D D1 E F G I L M N OMulticalor TS 100 AB/AB 619 454 165 175 395 750 190 250 190 190 M10 140 165Multicalor TS 140 AB/AB 619 454 165 307 457 750 215 250 190 190 M10 140 165
D = short head D1 = long head
L
I
M
CBA
D - D1E
N
G
F
O
Dimensions (mm)
5,6315,63151 51
303
1515
222
252
216°N01R
40172
40
0432204
AIR FLANGE
pag.3
420010602300 Multicalor TS 100-140 AB/AB
ELECTRICAL CONNECTIONSAll burners are factory tested and set at 400 V 50 Hz three-phase for motors and 230 V 50 Hz monophase with neutralfor auxiliaries. If it is necessary to supply the burner at 230 V 50 Hz without neutral,make the necessary alterationsreferring to the wiring diagram of the burner and check that the termal relay is within the absorption range of themotor. Also check that the fan motor rotates in the correct direction.
CONNECTION TO THE GAS PIPELINE Once connected the burner to the gas pipeline, it is necessary to control that this last is perfectly sealed. Also verify thatthe chimney is not obstructed. Open the gas cock and carefully bleed the piping through the pressure gauge connector,then check the pressure value trough a suitable gauge. Power on the system and adjust the thermostats to the desiredtemperature. When thermostats close, the sealing control device runs a seal test of valves; at the end of the test the bur-ner will be enabled to run the start-up sequence.
OPERATION OF BURNER WITH GASPRELIMINARY CHECKSBefore starting up the boiler check the following:• gas type and feed pressure;• gas valves closed;• the seals in the pipe fittings;• gas pipe breather and input pressure;• that the cable complies with the diagram and the phase and neutral wires correspond;• that the burner shuts down when the boiler thermostat opens• the seal of the boiler furnace which prevents air from entering• the seal on the flue-boiler pipe fitting;• the condition of the flue (sealed, free from blockage, etc.).If all these conditions are present, start the burner. The control device starts the motor to carryout prewashing of the combustion chamber. During this prewash period (about 30 seconds) the device checks that airpressure is correct via the air pressure switch. At the end, it supplies power to the transformer and opens the gas valves.The flame must be lit and stabilize within 3 seconds, which is the device's safety time limit. Check to ensure the flameis lit before placing any control instrument in the flue. Adjust and check the gas flow necessary for the boiler at themeter. Adjust the air flow according to the gas flow to obtain correct combustion.IMPORTANT ADVICEAll adjustable parts must be fixed by the installer after making adjustments. Check flue combustion after each adjust-ment. The CO2 values must be approx. 9.7 (G20) 9.6 (G25) 11.7 (G30) 11.7 (G31) and the CO must be less than 75ppm.
0
12
0 - STOP1 - GASOLIO2 - GAS
LIGHT-OIL
ADJUSTING THE COMBUSTION PROCESSIMPORTANT: to obtain the right adjustment of the combustion and thermal capacity it is important to analyze thereducts of combustion with the aid of suitable instruments. The combustion and thermal capacity adjustment is donesimultaneously, together with the analysis of the products of combustion, making sure that the measured values are sui-table and that they comply with current safety standards. On this matter, please refer to the table and figure below.THESE OPERATIONS MUST BE DONE BY PROFESSIONALLY-QUALIFIED TECHNICIANS.NOTE: ALL SAFETY DEVICES (AIR PRESSURE SWITCH, MINIMUM GAS PRESSURE SWITCH, GASSOLENOID VALVES AND GAS GOVERNOR) SHALL BE DULY SEALED AFTER CALIBRATION AND BUR-NER START UP BY EACOON TECHNICIANS.
21 3 4 5
6
7
BURNER INSTALLATION
1 - BURNER 2 - NUT 3 - WASHER 4 - GASKET 5 - BOLT 6 - BOILER 7 - GASKET
pag.4
420010602300 Multicalor TS 100-140 AB/AB
EC
CE
SS
O D
'AR
IA (
%)
FA
TT
OR
E D
'AR
IA10
10 20 30 40 50 6070
8090
100 200 300 400500
600700
800900
1000 20001,1
1,15
1,21,2 1,2
1,25
1,3
15
20
25
30
POTENZA UTILE NOMINALE (kW)
SUGGESTED REFERENCE VALUES
Natural Gas
CO2 9,6%
CO <100 ppmE
XC
ES
S A
IR (
%)
AIR
FA
CT
OR
RATED USEFUL CAPACITY (KW)
To calculate the burner’s working output, in kW, proceed as follows:
- Check at the meter the quantity of supplied litres and the duration, in seconds, of the reading, then calculate the burner’s output through the following formula:
CALCULATION OF WORKING OUTPUT OF THE BURNER
e x f = kWs
e = Litres of gass = Time in seconds
G20 = 34,02G25 = 29,25G30 = 116G31 = 88
f
GAS CIRCUIT
1° STADIO GAS
ASPIRAZIONE
RITORNO
VgS
Vg2
Vg11 2 3
4
5
6VGVGS987
1 - PUMP2 - SAFETY LIGHT-OIL VALVE3 - LOW FLAME LIGHT-OIL VALVE4 - HIGH FLAME LIGHT-OIL FLAME5 - LOW FLAME NOZZLE6 - HIGH FLAME NOZZLE7 - MINIMUM GAS PRESSURE SWITCH8 - SAFETY GAS VALVE9 - GAS VALVE
2 STADIO GAS
ASPIRAZIONE
RITORNO
VgS
Vg2
Vg11 2 3
4
5
6VGVGS987
SUCTION
RETURN
SUCTION
RETURN
Low flame stage High flame stage
LANDIS LGB 22 UP-CYCLEThe control box starts theburner fan, to carry outthe prepurging of the com-bustion chamber, andcheks the vent air pressurethrough the air pressureswitch. At the end of pre-purging, the ignition tran-sformer cuts-in and gene-rates a spark between theelectrodes. At the sametime the two gas valves open (Vs safety valve and Vl Low flame working valve).The total safety, in case of missed ignition or casual burner's flame-out, is gran-ted by a ionisation probe which cuts-in and sets the burner shutdown withinthe safety time. In case of gas lack or a major pressure drop, the minimum airpressure switch shuts down the burner.
t1
t2 t3 t2 t3
t5
t4
t6
t1
t5
t4
Lock out lamp
Flame detection
Gas valve
High flame ON/OFF
Transformer
Air pressure switch
Motor
Gas pressure switch
Normal operative cycle ignition Operative cycle with flameless
Description t1 pressure switch control time-out 9"
t2 time-out for air pressure confirmation 3"
t3 prewashing time 30"
t4 safety time 3"
t5 preignition time 3"
t6 time-out to enable fuel 2nd valve 8"
pag.5
420010602300 Multicalor TS 100-140 AB/AB
ADJUSTMENT OF GAS MINIMUM PRESSURE SWITCHUnscrew off and remove cover M. - Set regulator N to a value equal to 60% of gas nominalfeed pressure (i.e. for nat. gas nom. pressure = 20 mbar, set regulator to a value of 12 mbar;for L.P.G. nom. pressure of G30/G31- 30/37 mbar, set regulator to a value of 18mbar).Screw up cover M.
ADJUSTMENT OF THE AIR PRESSURE SWITCHUnscrew screws A and B and remove cover C.- Set the pressure switch to the mini-mum by turning regulator D to position 1. - Start the burner and keep in low flamerunning, while checking that combustion is correct. Through a small cardboard, pro-gressively obstruct the air intake until to obtain a CO2 increase of 0,5÷0,8% or else,if a pressure gauge is available, connected to pressure port E, until reaching a pressuredrop of 1 mbar (10 mm of W.G.). - Slowly increase the adjustment value of the airpressure switch until to have the burner lockout. Remove the obstruction from the airintake, screw on the cover C and start the burner by pressing the control box rearmbutton. Note: The pressure measured at pressure port E must be within the limits of thepressure switch working range. If not, loose the locking nut of screw F and gradually turnthe same: clockwise to reduce the pressure; counterclockwise to increase. At the end tightenthe locking nut.
2,55
10 15
50
25
35
30
4045
20
0,4
0,6 0,9
3,0
1,5
2,1
1,8
2,42,7
1,2
I
L
MN
A
B
CD
EG
H
gas pressure switch
air pressure switch
ADJUSTEMENT OF THE COMBUSTION AIR
SIEMENS SQN 30 151A2700 AIR DAMPER MOTORRemove cover to gain access to the adjusting cams.The cams are to beadjusted through the suitable key provided for. Description: I - Limit switch for air damper “High Flame” position adjustment
(Max. power)II - Limit switch for the air damper position at burner’s shut downIII - Limit switch for air damper “Low Flame” position adjustment
(Min. power)V - Limit switch for 2nd stage’s solenoid valve opening releaseNOTE : Cam V (to allow the 2nd stage’s solenoid valve opening) must beadjusted to an intermediate position between the Low and High Flameones (to an angle approximately 5° greater than the low flame position).
MANUAL RELEASE SWITCH
GAS TRAIN INSTALLATION AND SETTING INSTRUCTIONS
Fix the gas train to burner body by means of the 4 screws of the flange, pay attention to set correctly the gasket ( O-ring ). Connect electrically the gas train with the 6 pole plug.Switch on the burner (it has already been tested in the factory, so it is pre set on average values) and verify the tightnessof gas train connections made during installation.Act as follows to adapt the burner output to the boiler.
HIGH FLAME1. Bring the burner in high flame , air inlet must be set at 75 ° (maximum opening position).To adjust air capacity operate on the combustion head position.Just in peculiar case it is necessary to reduce the air flow in high flame closing air intake damper.2. The position of gas butterfly valve must be lower then 90° ( typically 85°. It is important not get over 90° to obtaina perfect combustion during passage from high to low flame). Eventually adjust this position acting on the screw “1 “,after loosening nut “ 2 “.3. Regulate gas capacity in high flame through the gas governor, or operate on the adjustable gas valve.
pag.6
420010602300 Multicalor TS 100-140 AB/AB
4
3
2
1
The control of the detector current shall be carried out by plugging a microampe-rometer with full scale at 1000 µA (D.C.) in series with the UV-cell. If the detec-tor current is too low verify the connection between phase and neutral of the bur-ner and the grounding of the burner itself. Minimum required detector current is200 µA.
LGB 22
QRA
AGQ
1.1A
27 1
2
SW
SW
BL
BL
FLAME DETECTOR SYSTEM CHECK
SW = BLACKBL = BLU
Attention : The support of UV-cell A must be connected withthe pipe to the fan ventilator before heat exchan-ger (this pipe is very important in order to put thefresh air into the UV-cell). If you not connectedthis pipe the UV-cell can damage.
A
LOW FLAME4. Choose the first stage position on the servocontrol ( normally between 10° - 30°) on the basis of the reduced chargeoutput required and switch the burner to low flame.5. Regulate gas capacity, to obtain optimal combustion, changing the position of the gas valve disc, act on screw “ 3 “,after loosen nut “ 4 “.
Final operations6. Bring the burner in high flame again, if necessary adjust again gas flow (as shown in point n.2).7. If necessary repeat operations described on point n. 5 and n. 6 until You obtain the exact position of the gas flowboth in high and low flame.8. Fix the nuts.
420010602300 Multicalor TS 100-140 AB/AB
ADJUSTING THE FIRING HEAD
The adjustment of the combustion head position is carried out inorder to obtain the best combustion efficiency. When installed forsmall output operations, the head shall be adjusted back.For maximum operation the position is fully forward. Steps: loosen the locking screw of A lever. Move the lever to theneeded position. Tighten back the locking screw.
A
min. max.
MULTICALOR120-140
I
0
REMOVING THE BLAST TUBE
pag.7
1° STADIO GASOLIO
ASPIRAZIONE
RITORNO
VgS
Vg2
Vg11 2 3
4
5
6VGVGS987
LIGHT-OIL CIRCUITA - HOSEB - OIL FILTER C - OIL COCK 1 - PUMP2 - SAFETY LIGHT-OIL VALVE3 - LOW FLAME LIGHT-OIL VALVE4 - HIGH FLAME LIGHT-OIL FLAME5 - LOW FLAME NOZZLE6 - HIGH FLAME NOZZLE7 - MINIMUM GAS PRESSURE SWITCH8 - SAFETY GAS VALVE9 - GAS VALVE
A
A
B C
2° STADIO GASOLIO
ASPIRAZIONE
RITORNO
VgS
Vg2
Vg11 2 3
4
5
6VGVGS987
Low flame stage
High flame stage
SUCTION
RETURN
SUCTION
RETURN
pag.8
420010602300 Multicalor TS 100-140 AB/AB
The pump is adjusted during testing and inspection to 12 bar. VERIFY: - That pipingsystem is perfectly sealed; - That the use of hoses is avoided whenever is possible (usecopper pipes preferably); - That depression is not greater than 0,45 bar, to avoid pump’s
cavitation; - That check valve is suitably designed for the duty; The pump pressure is set at a value of 12 bar duringthe testing of burners. Before starting the burner, bleed the air in the pump through the gauge port. Fill the piping withlight-oil to facilitate the pump priming. Start the burner and check the pump feeding pressure. In case the pump pri-ming does not take place during the first prepurging, with a consequent, subsequent lock-out of the burner, rearm theburner’s lock-out to restart, by pushing the button on the control box. If, after a successful pump priming, the burnerlocks-out after the prepurging, due to a fuel pressure drop in the pump, rearm the burner’s lock-out to restart the bur-ner. Do not allow the pump to work without oil for more than three minutes. NOTE: Before starting the burner, check that the return pipe is open. An eventual obstruction could damage thepump sealing device.
PRIMING AND ADJUSTMENT OF OIL PUMP
1 - INLET 2 - RETURN 3 - BLEED AND PRESSURE GAUGE PORT4 - VACUUM GAUGE PORT 5 - PRESSURE ADJUSTMENT6 - TO NOZZLE
SUNTEC AN 77
6 5
4
3 3
3
SUNTECSUNTEC
P V
21
H (m)Dall'asse
della pompa
Lunghezza tubazioni
ø 10mm
ø 12mm
00,5123
3,5
323640485660
909090909090
ø 12mm
ø 14mm
666558453225
909080806552
AS 67AN 77
(m)AJ 6(m)
252118105-
706254382010
666052402519
909090805845
RSA 60(m)
RSA 125(m)
ø 10mm
ø 12mm
ø 10mm
ø 12mm
ø 15mm
-4853637378
-99100100100100
-2225293436
-4651617176
-100100100100100
H (m)Dall'asse
della pompa
Lunghezza tubazioni
ø 10mm
ø 12mm
00,5123
3,5
ø 12mm
ø 14mm
AS 67AN 77
(m)AJ 6(m)
RSA 60(m)
RSA 125(m)
ø 10mm
ø 12mm
ø 10mm
ø 12mm
ø 15mm
43373222127
887867462515
2018151063
41363122127
1008977532917
H
H
Bitubo dalla sommità del serbatoio
Bitubo in aspirazione
The correct length of pipes is calculated by summing up the length of all vertical and horizontal right sections andbends. The static suction head will be the distance between the non-return valve and the burner’s pump axle. The depression must not be greater than 0.45 bar; should it be higher, some damage could occur to the pump, withconsequent increase in mechanical noises and ,eventually, a failure.
MAXIMUM LENGTH OF SUCTION LINES FOR TWO-PIPE SYSTEM
Two-pipe lift system
Two-pipe siphon feed system PIPE LENGTH
PIPE LENGTH
pag.9
420010602300 Multicalor TS 100-140 AB/AB
NOZZLE PUMP PRESSURE (bar)GPH 10 11 12 13 14 15 162,50 9,50 9,97 10,41 10,83 11,24 11,64 12,023,00 11,40 11,96 12,49 13,00 13,49 13,96 14,423,50 13,30 13,95 14,57 15,17 15,74 16,29 16,834,00 15,20 15,94 16,65 17,33 17,99 18,62 19,234,50 17,10 17,94 18,73 19,50 20,24 20,95 21,635,00 19,00 19,93 20,82 21,67 22,48 23,27 24,045,50 20,90 21,92 22,90 23,83 24,73 25,60 26,446,00 22,80 23,92 24,98 26,00 26,98 27,93 28,846,50 23,70 25,91 27,06 28,17 29,23 30,26 31,257,00 26,60 27,90 29,14 30,33 31,48 32,58 33,657,50 28,50 29,90 31,22 32,50 33,73 34,91 36,058,30 31,54 33,08 34,55 35,97 37,32 38,63 39,909,50 36,10 37,87 39,55 41,17 42,72 44,22 45,6710,50 40,06 41,73 43,74 45,41 47,20 48,90 50,5012,00 45,60 47,80 50,00 52,00 54,00 55,90 57,7013,80 52,40 55,00 57,50 59,80 62,10 64,20 66,3015,30 58,10 61,00 63,70 66,30 68,80 71,10 73,6017,50 66,50 69,80 72,90 75,80 78,70 81,50 84,1019,50 74,10 77,70 81,20 84,50 87,70 90,80 93,7021,50 81,70 85,70 89,50 93,20 96,70 100,10 103,4024,00 91,20 95,70 99,90 104,00 107,90 111,70 115,40GPH OUTPUT kg/h
NOZZLE FLOW RATE (DELAVAN B - MONARCH PLP)
pag.10
420010602300 Multicalor TS 100-140 AB/AB
NOZZLE CLEANING AND REPLACEMENTUse only the suitable box wrench provided forthis operation to remove the nozzle, takingcare to not damage the electrodes. Fit the newnozzle with the same care.Note: Always check the position of electrodesafter having replaced the nozzle (see illustra-tion). A wrong position could cause ignitiontroubles.
5÷6 mm
3÷4 mm
2 fiamme
OPERATION OF BURNER WITH LIGHT-OIL FUEL Gas/Light-oil dual burners must always be adjusted for a first light-oil ignition. After having installed the burner, checkthe following points: Feeding voltage and protection fuses - Motor connections – The correctness of pipe system lengthand its sealing – The type of fuel, which must be suitable for the burner - The connections of boiler’s thermostats andthe safety devices – The direction of motors rotation – The correct calibration of motors protections – The nozzles flowrate must be suitable for the boiler’s output – At the end, fit a manometer on the pump itself. When all the above con-ditions are met, it will, then, be possible to proceed with the burner start-up. Switch the burner ON. The control boxwill power up the fuel pump and the fan’s motor, thus allowing a prepurging of the combustion chamber at the maxi-mum air flow rate. At the end of prepurging, the servomotor will set up to the light-oil Low flame position, whilst thecontrol box powers up the ignition transformer and the “Safety” and “Low flame” solenoid valves.If the burner ignitesnormally, after a safety time of 3 sec. the control box will power off the ignition transformer and after 10 secs. operatesthe air damper’s servomotor, bringing the burners to High flame operation. In case of faulty ignition, the control boxwill shut down the burner to lockout position within 3 sec. In this case, the burner must be reset manually, by pressingthe lockout enable pushbutton on the control box itself. In order to obtain a correct combu-stion, it will be necessary to adjust the Low and High flame by following the instructionsshowed at pages 8÷9 (Air servomotor and firing head adjustment). During the adjustingphase, it will be possible to manually switch, back and forth, from Low flame to High flamethrough the High-Low flame manual switch. When all the adjusting operations are achieved,leave the switch in High flame position. For a correct reading and calibration, carry out the combustion analysis in thechimney.
0
12
0 - STOP1 - GASOLIO2 - GAS
LIGHT-OIL
The burners are produced with connections suitable for power supply 400 V three-phase.The burners with electric motors of an output lower or equal to 7,5 kW can be adapted to 220-230 V (please follow theinstructions on the backside); motors with higher output can only work 380-400 V three-phase.In case of request of burners different from the above mentioned standard, it is recommended to make specific mentionin the order.
Instructions: how to adapt electric motors of an output lower or equal to 7,5 kW to 220-230 V power supplyIt is possible to change the voltage of the burner by operating as follows:1. change the connection inside the electric box of the motor, from star to delta (see picture);2. change the setting of the thermal relay, referring to the absorption values indicated in themotor nameplate. If necessary, replace the thermal relay with another one of suitable scale.This operation is not possible on motors above 7.5 kW. For more information, please contact the Eacoon staff. 230V
400V
pag.11
420010602300 Multicalor TS 100-140 AB/AB
MAINTENANCE
YEARLY CHECKSThe burner’s periodical check (firing head, electrodes etc.) must be carried out by authorised personnel one or twotimes per year, depending on the utilisation. Before going on with the maintenance controls of the burner, it should beadvisable to check its general conditions, according to the following steps:
Unplug the burner; close the fuel cock; shut down the gas supply; remove burner’s cover and clean the fan and airintake; clean the firing head and check the electrode’s position; reassemble all the parts; check the connection’s sealing;check the chimney; start the burner and check the combustion flue (CO2 = 9.5 ÷ 9.8; O = lower than 75 ppm).
BEFORE EVERY INTERVENTION CHECK:The electric system is duly powered and the burner is plugged in. The gas pressure must be the suitable one and the gas cock open. The control devices must be properly connected. When all the above conditions are met, start the burner by pressing the lockout enable pushbutton. Check the burner’s cycle.
THE BURNER DOES NOT START:Check the ON/OFF switch, the thermostats, the motor and the gas pressure. The master switch is in position “0”. Fuses are blown out. The control box is faulty.
THE BURNER RUNS THE PREPURGING AND SWITCHES TO LOCKOUT AT THE END OF CYCLE:Check the fan and the air pressure. Check the air pressure switch. Control box faulty. Ignition transformer faulty. Check the ignition cable. Electrodes are dirty or in wrong position. Nozzles are clogged or worn. Filters are clogged. Light-oil pressure is too low. Combustion air’s flow rate too high related to nozzle output.
THE BURNER RUNS THE PREPURGING BUT DOES NOT IGNITE:Check the position of the electrodes; check the ignition cable; Check the ignition transformer; Check the control box.
THE BURNERS IGNITES BUT SWITCHES TO LOCKOUT AFTER THE SAFETY TIME:Check phase and neutral for a correct connection. Check gas solenoid valve. Check the position of ionisation probe and its connection. Check the control box. Check nozzles (clogged or worn). The photoresistor does not detect the flame. The filters are clogged. Light-oil pressure too low. Combustion air’s flow rate too high related to nozzle output.
THE BURNERS IGNITES BUT SWITCHES TO LOCKOUT AFTER FEW MOMENTS:Check gas governor and gas filter. Check gas pressure through a manometer. Check ionization value (min. 200 µA).
pag.12
420010602300 Multicalor TS 100-140 AB/AB
TOT.
SHEE
T
SHEE
TDE
SIGNE
RDE
SCRIP
TION
DATE
FIST
CREA
TION
CODE
SIGNA
TURE
R&D
DEPA
RTM
ENT
CONT
ROLL
EREc
oflam
Bru
ciat
ori
SERV
OMOT
OR
FLAM
E SEN
SOR
S.p.
AEC
N FIR
ST CR
EATIO
N
BY TERM LAWS WE RESERVED THE PROPERTY OF THIS WIRING DIAGRAM WITH PROHIBITION OF USE AND REPRODUCTION
LEAK
AGE C
ONTR
OL
CONT
ROL B
OX
DATE
ECN
MOD
ICAT
ION
MOD
IFICA
TION
DESC
RIPTIO
NEC
N M
ODIFI
CATIO
N
MUL
TICAL
OR TS
45-7
0-10
0 AB/
AB (Q
.C)
A.PO
ZZOB
ON
21-0
1-20
11
2
4201
1004
8300
1 A
.RIGO
NI
LAND
IS SQ
N 30
.151A
2700
UV
RBA1
0PC6
63LA
NDIS
LGB 2
2-LM
E 22
PRED
ISPOS
TO
F
1
ED
23
4
CBA
12
34
56
78
FED
56
7
CB
8
A
Q
FMV
97 98KT
_oil
KT_g
as
FMV95 96
SAsr
TP
STAB
KMV
RS
TNO
FMV
LINE
LOAD
Z
FU SAL
HLBT
SAgG
12
30
HLG
HLg
3M
MV
WV
U
SAM
A 12
30
SAM
A
12
30
HLB
HLF
43
21
TP
STC T
P
STS
HLB
NR
ST
107
65
98
11
RPE TS
50 H
z 40
0V
12
N
N18
1716
WV
UF
N
LAND
IS LG
B 22-L
ME 22
31
27
54
611
98
1012
3132
GAS (
2)GA
SOLI
O (1
)
AUTO
(3)
BLAC
KBL
UE
BROW
NRE
DAG
Q1.1A
27BL
UE
BLAC
K
103
104
106
107
108
105
102
101
6061
5156
5710
084
8544
4546
5090
9392
91
SWITC
H M
ANUA
L-AUT
OMAT
ICIN
TERR
RUPT
EUR M
ANUE
L-AUT
OMAT
IQUE
CONM
UTAD
OR M
ANUA
L-AUT
OMAT
ICO
COM
MUT
ATOR
E MAN
UALE
-AUT
OMAT
ICO
pos 1
: ALT
A FIA
MM
A/HI
GH FL
AME/
2meA
LLUR
E/AL
TA LL
AMA
pos 3
: AUT
OMAT
ICO/
AUTO
MAT
IC/A
UTOM
ATIQ
UE/A
UTOM
ATIC
Opo
s 2: B
ASSA
FIAM
MA/
LOW
FLAM
E/1r
e ALL
URE/
BAJA
LLAM
A
pag.13
420010602300 Multicalor TS 100-140 AB/AB
F
1
ED
23
4
CBA
12
34
56
78
FED
56
7
CB
8
A
TOT.
SHEE
T
SHEE
TDE
SIGNE
RDE
SCRIP
TION
DATE
FIST
CREA
TION
CODE
SIGNA
TURE
R&D
DEPA
RTM
ENT
CONT
ROLL
EREc
oflam
Bru
ciat
ori
SERV
OMOT
OR
FLAM
E SEN
SOR
S.p.
AEC
N FIR
ST CR
EATIO
N
BY TERM LAWS WE RESERVED THE PROPERTY OF THIS WIRING DIAGRAM WITH PROHIBITION OF USE AND REPRODUCTION
LEAK
AGE C
ONTR
OL
CONT
ROL B
OX
DATE
ECN
MOD
ICAT
ION
MOD
IFICA
TION
DESC
RIPTIO
NEC
N M
ODIFI
CATIO
N
MUL
TICAL
OR TS
45-7
0-10
0 AB/
AB (Q
.C)
A.PO
ZZOB
ON
21-0
1-20
11
2
4201
1004
8300
2 A
.RIGO
NI
LAND
IS SQ
N 30
.151A
2700
UV
RBA1
0PC6
63LA
NDIS
LGB 2
2-LM
E 22
PRED
ISPOS
TO
HIGH
-LOW
FLAM
E THE
RMOS
TAT
THER
MOS
TAT G
RAND
E-PET
IRE A
LLUR
ETE
RMOS
TATO
DE A
LTA-
BAJA
LLAM
A
TERM
OSTA
TO D
E SEG
URID
AD
SWITC
H (O
IL-GA
S-AUT
O)
TERM
OSTA
TO D
I ALT
A-BA
SSA
FIAM
MA
INTE
RRUT
TORE
GAS
OLIO
-GAS
-AUT
O
INTE
RRUP
TEUR
MAZ
OUT-G
AZ-A
UTO
CONM
UTAD
OR G
ASOL
EO-G
AS-A
UTO
STAB
SAgG
TERM
OSTA
TO D
I SIC
UREZ
ZASA
FETY
THER
MOS
TAT
THER
MOS
TAT D
E SEC
URITE
STS
ESPIA
DE B
LOQU
EO RE
LE TE
RMICO
LAM
PE D
E THE
RMAL
DE S
ECUR
ITETH
ERMA
L LOC
K-OU
T LAM
PHL
BTLA
MPA
DA D
I BLO
CCO
TERM
ICO
TERM
OSTA
TO CA
LDER
ATH
ERM
OSTA
T CHA
UDIER
EBO
ILER T
HERM
OSTA
TTE
RMOS
TATO
CALD
AIA
STC
FILTR
O DE
PROT
ECIO
N A
NTID
ISTUR
BIOFIL
TRE A
NTIPA
RASIT
ESAN
TJAM
MIN
G FIL
TER
FUSIB
LEFU
SIBLE
FUSE
MOT
OR VE
NTILA
DOR
MUT
EUR V
ENTIL
ATEU
RM
OTOR
FAN
RELE
' TER
MICO
MOT
OR VE
NTILA
DOR
RELA
IS TH
ERM
IQUE
MOT
EUR V
ENTIL
ATEU
RM
OTOR
THER
MAL R
ELAY
(FAN
MOT
OR)
ESPIA
GAS
LAM
PE D
E GAZ
GAS L
AMPE
ESPIA
DE B
LOQU
EOLA
MPE
DE S
ECUR
ITELO
CK-O
UT LA
MP
ESPIA
GAS
OLEO
TEM
OIN
MAZO
UTOI
L OR L
AMP
TELE
RRUP
TOR M
OTOR
VENT
ILATO
RCO
NTAC
TEUR
MOT
EUR V
ENTIL
ATEU
RRE
MOT
E CON
TROL
SWITC
H (FA
N M
OTOR
)
INTE
RRUP
TOR G
ENER
AL CO
N FU
SIBLE
INTE
RRUP
TEUR
GEN
ERAL
AVEC
FUSIB
LEMA
IN SW
ITCH
WITH
FUSE
INTE
RRUP
TOR D
E LIN
EAIN
TERR
UPTE
UR D
E LIG
NEW
ORKIN
G SW
ITCH
INTE
RRUT
TORE
DI L
INEA
SAL
CONT
ATTO
RE M
OTOR
E VEN
TILAT
ORE
KMV
SAMA
LAM
PADA
GAS
OLIO
HLg
LAM
PADA
GAS
HLG
LAM
PADA
DI B
LOCC
OHL
B
RELE
' TER
MICO
MOT
ORE V
ENTIL
ATOR
EFM
V
MOT
ORE V
ENTIL
ATOR
EM
V
FUSIB
ILEFU
FILTR
O AN
TIDIST
URBO
Z
INTE
RRUT
TORE
GEN
ERAL
E CON
FUSIB
ILEQ
KT_g
as
KT_o
ilTE
MPO
RIZZA
TORE
TIMER
TEM
PORIS
ATEU
RTIE
MPO
RIZAD
OR
TEM
PORIZ
ZATO
RETIM
ERTE
MPO
RISAT
EUR
TIEM
PORIZ
ADOR
COM
MUT
ATOR
E MAN
UALE
-AUT
OMAT
ICOSW
ITCH
(MAN
UAL-A
UTOM
ATIC
))IN
TERR
UPTE
UR M
ANUE
L-AUT
OMAT
IQUE
CONM
UTAD
OR M
ANUA
L-AUT
OMAT
ICO
SA s.
rPU
LSAN
TE D
I SBL
OCCO
APP
AREC
CHIAT
URA
RESE
T LOC
K OUT
BUTT
ONBO
UTON
DE D
EBLO
CAGE
DU
COFF
RE D
E SEC
URITE
REAR
ME D
E LA
CENT
RALIT
A
pag.14
420010602300 Multicalor TS 100-140 AB/AB
TOT.
SHEE
T
SHEE
TDE
SIGNE
RDE
SCRIP
TION
DATE
FIST
CREA
TION
CODE
SIGNA
TURE
R&D
DEPA
RTM
ENT
CONT
ROLL
EREc
oflam
Bru
ciat
ori
SERV
OMOT
OR
FLAM
E SEN
SOR
S.p.
AEC
N FIR
ST CR
EATIO
N
BY TERM LAWS WE RESERVED THE PROPERTY OF THIS WIRING DIAGRAM WITH PROHIBITION OF USE AND REPRODUCTION
LEAK
AGE C
ONTR
OL
CONT
ROL B
OX
DATE
ECN
MOD
ICAT
ION
MOD
IFICA
TION
DESC
RIPTIO
NEC
N M
ODIFI
CATIO
N
MUL
TICAL
OR TS
45-7
0-10
0-12
0-14
0 AB/
AB (Q
.D)
A.PO
ZZOB
ON
21-0
1-20
11
2
4201
1004
8400
1 A
.RIGO
NI
LAND
IS SQ
N 30
.151A
2700
UV
RBA1
0PC6
63LA
NDIS
LGB 2
2-LM
E 22
PRED
ISPOS
TO
F
1
ED
23
4
CBA
12
34
56
78
FED
56
7
CB
8
A
M1
MP
FN
-+UV 1
2
PT
SPA
TVYV
gSYV
g1YV
g2
87
64
52
31
NLA
NDIS
SQN3
0.151
A270
0
S3T2
NT1
L191
9293
9050
4645
4485
8410
057
5651
6160
101
102
105
108
107
106
NF
104
103
YVG
YVGS
T2N
T1S3
L1
BLUE
YELLOW-GREEN
BLACK
BROWN
CONT
ROLE
D'ET
ANCH
EITI
CONT
ROL D
E EST
ANQU
IDAD
PRED
ISPOS
ICIO
N
PREV
U PO
UR LE
PRED
ISPOS
EDLE
KAGE
CONT
ROL
PRED
ISPOS
IZION
ECO
NTRO
LLO
DI TE
NUTA
TP
SPGm
in
pag.15
420010602300 Multicalor TS 100-140 AB/AB
F
1
ED
23
4
CBA
12
34
56
78
FED
56
7
CB
8
A
TOT.
SHEE
T
SHEE
TDE
SIGNE
RDE
SCRIP
TION
DATE
FIST
CREA
TION
CODE
SIGNA
TURE
R&D
DEPA
RTM
ENT
CONT
ROLL
EREc
oflam
Bru
ciat
ori
SERV
OMOT
OR
FLAM
E SEN
SOR
S.p.
AEC
N FIR
ST CR
EATIO
N
BY TERM LAWS WE RESERVED THE PROPERTY OF THIS WIRING DIAGRAM WITH PROHIBITION OF USE AND REPRODUCTION
LEAK
AGE C
ONTR
OL
CONT
ROL B
OX
DATE
ECN
MOD
ICAT
ION
MOD
IFICA
TION
DESC
RIPTIO
NEC
N M
ODIFI
CATIO
N
MUL
TICAL
OR TS
45-7
0-10
0-12
0-14
0 AB/
AB (Q
.D)
A.PO
ZZOB
ON
21-0
1-20
11
2
4201
1004
8400
1 A
.RIGO
NI
LAND
IS SQ
N 30
.151A
2700
UV
RBA1
0PC6
63LA
NDIS
LGB 2
2-LM
E 22
PRED
ISPOS
TO
ELEC
TROV
ALVU
LA D
E GAS
OLEO
DE S
EGUR
IDAD
ELEC
TROV
ANNE
MAZ
OUT D
E SEC
URITE
EXTR
A SA
FETY
OIL
SOLE
NOID
VALV
EEL
ETTR
OVAL
VOLA
GAS
OLIO
DI S
ICUR
EZZA
ELEC
TROV
ALVU
LA D
E GAS
OLEO
1^ LL
AMA
ELEC
TROV
ANNE
MAZ
OUT P
ETITE
ALL
URE
FIRST
STAG
E OIL
SOLE
NOID
VALV
EEL
ETTR
OVAL
VOLA
GAS
OLIO
DI P
RIMA
FIAM
MA
ELEC
TROV
ALVU
LA D
E GAS
ELEC
TROV
ANNE
GAZ
GAS S
OLEN
OID
VALV
EEL
ETTR
OVAL
VOLA
GAS
SPA
AIR P
RESS
URE S
WITC
H
PRES
OSTA
TO A
IREPR
ESSO
STAT
AIR
PRES
SOST
ATO
ARIA
YVG
YVg1
YVg2
YVgS
ELEC
TROV
ANNE
MAZ
OUT D
E SEC
URITE
EXTR
A SA
FETY
OIL
SOLE
NOID
VALV
EEL
ETTR
OVAL
VOLA
GAS
OLIO
DI S
ICUR
EZZA
ELEC
TROV
ALVU
LA G
AS D
E SEG
URID
ADEL
ECTR
OVAN
NE G
AZ D
E SEC
URITE
EXTR
A SA
FETY
GAS
SOLE
NOID
VALV
EEL
ETTR
OVAL
VOLA
GAS
DI S
ICUR
EZZA
YVGS
SPGm
in
ELEC
TROV
ALVU
LA D
E GAS
OLEO
DE S
EGUR
IDAD
PRES
OSTA
TO G
AS D
E MIN
IMA
POT.
PRES
SOST
AT G
AZ PR
ESSIO
N M
INGA
S PRE
SSUR
E SW
ITCH
MIN
PRES
SOST
ATO
GAS D
I MIN
IMA
MOT
OR BO
MBA
MOT
EUR P
OMPE
OIL P
UMP M
OTOR
TRAN
SFOR
MADO
RTR
ANSF
ORMA
TEUR
D'AL
LUMA
GEIG
NITIO
N TR
ANSF
ORM
ER
FOTO
CELU
LACE
LLUL
E UV
UV CE
LLFO
TOCE
LLUL
AUV
TRAS
FORM
ATOR
ETV
MOT
ORE P
OMPA
MP
YVG
YVGS
S3N
T1T2
L1
TP
SPGm
in
BLACK 31BLUE
1314
BROWN DUNG
S VDK
200-A
2
YELLOW-GREEN
1
T2N
T1S3
L1
TP
SPGm
in
BLACK L1
BLUE NB5
BROWN
T7T6
T8DU
NGS V
PS 50
4
YVG
YVGS
21
YELLOW-GREEN
pag.16
420010602300 Multicalor TS 100-140 AB/AB
23
0
90
Mul
tical
or T
S 10
0 A
B/A
B
21
22
14
16
17
15
18
20
13
1
3026
19
11
89
10
2431
292827
2532
33
3435
36
74
32
6
12
5
pag.17
420010602300 Multicalor TS 100-140 AB/AB
23
0
90
Mul
tical
or T
S 14
0 A
B/A
B
21
22
14
16
17
15
18
20
13
1
3026
74
32
6
19
1211
89
10
2431
292827
2532
33
3435
36
5
pag.18
420010602300 Multicalor TS 100-140 AB/AB
TC = SHORT HEAD TL = LONG HEAD
Multicalor TS 100
AB/AB
N° DESCRIPTION code
1 AIR PRESSURE SWITCH DUNGS LGW10 A2P 65323047
2 DOWN COVER 65324164
3 UP COVER 65324163
4 GLASS 65321883
5 GASKET 28x28 65321948
6 GLASS 30x50 65321949
7 GLASS COVER 65321884
8 CONTROL BOX BASE SIEMENS AGQ1.1A27 65322038
9 ADAPTER SIEMENS 65320092
10 CONTROL BOX SIEMENS LGB 22.330 A27 65320034
11 IGNITION TRANSFORMER COFI TRS 1020/21 65323223
12 UV CELL SIEMENS QRA2 65320075
13 IGNITION CABLE TC 65322003
TL
14 IGNITION ELECTRODES SET 65322322
15 PIPE 65321638
16 ROD 65325452
17 FIRING HEAD TC 65321639
TL 65321640
18 REAR DISC 65320733
19 FRONT DISC 65320808
20 NOZZLE HOLDER 65320711
21 INNER ASSEMBLY TC
TL
22 BLAST TUBE TC 65320402
TL 65320403
23 GASKET 65321117
24 AIR DAMPER MOTOR SIEMENS SQN 30.151A2700 65322897
25 OIL PUMP SUNTEC AN 77A 72552P 65322953
26 COUPLING 65322918
27 NIPPLE TN 10X1200 65323188
28 HOSES TN 14X1200 65323184
29 OIL FILTER art. 70301-01P 65324051
30 PUMP MOTOR 200 W 65322789
31 CONDENSATOR 6,3 µF 65321852
32 OIL VALVE 1/8 F-F 230- 50-60 65325784
33 COIL DELTA 65323765
SUNTEC 65323767
34 OIL VALVE PARKER SCEM VE131 65323624
35 COIL PARKER 65323782
36 PLUG WIELAND 6 pin 65322072
pag.19
420010602300 Multicalor TS 100-140 AB/AB
Multicalor TS 140
AB/AB
N° DESCRIPTION code
1 AIR PRESSURE SWITCH DUNGS LGW10 A2P 65323047
2 DOWN COVER 65324164
3 UP COVER 65324163
4 GLASS 65321883
5 GASKET 28x28 65321948
6 GLASS GASKET 30x50 65321949
7 GLASS COVER 65321884
8 CONTROL BOX BASE SIEMENS AGQ1.1A27 65322038
9 ADAPTER SIEMENS 65320092
10 CONTROL BOX SIEMENS LGB 22.330 A27 65320034
11 IGNITION TRANSFORMER COFI TRS 1020/21 65323223
12 UV CELL SIEMENS QRA2 65320075
13 IGNITION CABLE TC 65322002
TL
14 IGNITION ELECTRODES SET 65322322
15 PIPE 65321638
16 ROD 65320230
17 FIRING HEAD TC 65321641
TL 65321642
18 DISC ASSEMBLY 65322310
19 FRONT DISC 65320808
20 NOZZLE HOLDER 65320711
21 INNER ASSEMBLY TC 65325175
TL
22 BLAST TUBE TC 65320419
TL 65320420
23 GASKET 65321119
24 AIR DAMPER MOTOR SIEMENS SQN 30.151A2700 65322897
25 OIL PUMP SUNTEC AJ6CC10002P 65322950
26 COUPLING 65325387
27 NIPPLE TN 10X1200 65323188
28 HOSES TN 14X1200 65323184
29 OIL FILTER art. 70301-01P 65324051
30 PUMP MOTOR 370 W 65322775
31 CONDENSATOR 14 µF 65321854
32 OIL VALVE 1/8 F-F 230- 50-60 65325784
33 COIL DELTA 65323765
SUNTEC 65323767
34 OIL VALVE PARKER SCEM VE131 65323624
35 COIL PARKER 65323782
36 PLUG WIELAND 6 pin 65322072
TC = SHORT HEAD TL = LONG HEAD
Ecoflam Bruciatori S.p.A. via Roma, 64 - 31023 RESANA (TV) - Italy - tel. 0423.719500 - fax 0423.719580 http://www.ecoflam-burners.com - e-mail: [email protected]
"società soggetta alla direzione e al coordinamento della Ariston Thermo S.p.A., via A. Merloni, 45 - 60044 Fabriano (An) CF 01026940427"
La ECOFLAM BRUCIATORI S.p.A si riserva il diritto di apportare ai prodotti quelle modifiche che riterrà necessarie outili, senza pregiudicarne le caratteristiche principali.
ECOFLAM BRUCIATORI S.p.A. reserves the right to make any adjustments, without prior notice, which it considersnecessary or useful to its products, without affecting their main features.
La Maison ECOFLAM BRUCIATORI S.p.A. se réserve le droit d’apporter les modifications qu’elle jugera nécessaires ouutiles à ses produits sans pour autant nuire à leurs caractéristiques principales.
ECOFLAM BRUCIATORI S.p.A. se reserva el derecho a introductor en sus productos todas las modificaciones queconsidere necesarias o utiles, sin prejudicar sus caracteristicas.
“Экофлам С.п.А.” оставляет за собой право вносить в конструкцию оборудования любые необходимыеизменения без особого предупреждения.