ge customized multi-unit prosthetic … abutment comes with its attached holder for easy transfer to...
TRANSCRIPT
GE M U L T I P L E - U N I T S C R E W - R E T A I N E D R E S T O R A T I O N S
H I G H L Y P E R F O R M I N G S O L U T I O N S
MULTI-UNIT AbutmentsGE
Pho
to c
redi
t: A
ntho
gyr
- A
ll ri
ghts
res
erve
d. N
on c
ontr
actu
al p
hoto
s.C1
58_G
B -
201
5-04
ERGONOMIC RANGECOMPREHENSIVE RANGE
A RANGE OF 24 ABUTMENTS!
w 5 Gingival heights: 0.75, 1.5, 2.5, 3.5 and 4.5 mm.
w The 20° morse taper on the platform allowsgreater correction of axial malalignment.
HIGH-PERFORMANCE RANGEINTEGRITY OF AXIOM® ANGULATED MULTI-UNIT ABUTMENTS:Thanks to a unique design, integrity of these screw-retained abutments can be maintained with no trade-off to the wall thickness in critical zones:
The coronal part of the abutment is not truncated in the area that receives the MU M1.4 screw.
The connection system is not truncated at the base of the abutment which accommodates the M1.6 screw.
1
2
Gingival Height (mm) 0.75 1.5 2.5 3.5 4.5
Number of scribe lines
on coronal part0 1 2 3 4
Ø 4.8 mm Multi-Unit Abutments
18°
Angulation
w Angulated abutments (18° and 30°) in both indexed and non-indexed versions.
20° 20° 20°
30°18° or
COMMON PLATFORM
Ø = 4.8 mm
NARROW PLATFORM
Ø = 4.0 mmCOMMON OR NARROW PLATFORMSw Axiom® REG/PX angulated AND straight abutments have
a common Ø 4.8 mm platform and a 2.5 mmcoronal height (CH).Indicated for most multiple-unit screw-retained restorations. Reduced inventory of auxiliary components.
w Axiom® REG/PX straight abutments havea narrow Ø 4.0 mm platform and a reduced 1.5 mmcoronal height (CH).Indicated for multiple-unit screw-retained restorationsin patients with a small inter-implant distance.
EASY HANDLINGw Each abutment comes with its attached holder for easyEach abutment comes with its attached holder for easyEach abutment comes with its attached holder
transfer to the patient’s mouth and safer placement.w Can be used with the angulated drill guide.
QUICK IDENTIFICATIONw Each abutment is laser marked with angulation
(18° or 30°) and gingival height (CH).
EASY MANIPULATIONw Straight abutments have a tapered end which greatly
facilitates insertion.Angulated non indexed abutments feature a repositioning fl at.
w The taper angle on the coronal platform facilitatesplacement of auxiliary components.
ANGULATED DRILL GUIDEfor dental restorations using a limited number of implants
w 30° scribe lines on the drill guide;w 2 mm diameter support tip;w Drill guide height corresponds to tooth height: 10 mm;w Semi-fl exible stainless steel adapts for variances in
anatomy;w Pre-assembled holder assists in achieving parallel
alignment of Multi-Unit abutments.
Anthogyr SAS2 237, Avenue André Lasquin74700 Sallanches - FrancePhone: +33 (0)4 50 58 02 37 Fax: +33 (0)4 50 93 78 60 www.anthogyr.com
FOR ALL PLURAL RESTORATIONSw Partial or complete screw-retained bridges using Multi-Unit straight AND angulated abutments with
a COMMON platform.w Multiple-unit screw-retained restorations using Multi-Unit straight abutments with a NARROW
platform in patients with a small inter-implant distance.
Abutments are supplied Q for immediate loading.Q for immediate loading.Q
Ht 0.75 Ht 1.5 Ht 2.5 Ht 3.5 Ht 4.5
Multiple-UnitScrew-Retained Restorations
GE M U L T I P L E - U N I T S C R E W - R E T A I N E D R E S T O R A T I O N S
GE Ø 4.8 mm MULTI-UNIT RANGEØ 4.8 mm MULTI-UNIT ABUTMENTS
25N.cm
Component Cat. No. Graphics
PROSTHETIC COMPONENTSFOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit protective cap (titanium)Supplied Q MUNCAP
Narrow Multi-Unit temporary coping (titanium)Supplied with one titanium MU M1.4 screw
MUNC100
Narrow Multi-Unit PEEK temporary coping Supplied with one titanium MU M1.4 screw
MUNC200
Narrow Multi-Unit defi nitive castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUNC300
Narrow Multi-Unit CoCr** defi nitive castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUNC400
15N.cm
15N.cm
15N.cm
Manuel
w Used with Axiom® REG/PX implants for multiple-unit or full arch screw-retained restorations.
w Straight AND angulated abutments sharing the same auxiliary components.
w Supplied Q with a pre-assembled holder .
w Auxiliary components have a “yellow“ code.
GE Ø 4.0 mm MULTI-UNIT RANGEØ 4.0 mm NARROW MULTI-UNIT ABUTMENTSw Used with Axiom® REG and Axiom® PX implants for multiple-unit screw-retained restorations in patients with a small
inter-implant distance.w Straight narrow abutments use dedicated auxiliary components.w Supplied Q with a pre-assembled holder .w Auxiliary components have a “green“ code, or are marked «N» for narrow.
25N.cm
Instrument Cat. No. Graphics
TIGHTENING INSTRUMENTS FOR Ø 4.8 mm & 4.0 mm STRAIGHT MULTI-UNIT ABUTMENTS
Multi-Unit mandrel for 4.8 mm and 4.0 mmstraight abutments (short and long)
MUM100 MUM100L
Multi-Unit wrench for 4.8 mm and 4.0 mmstraight abutments
MUW100
SURGICAL INSTRUMENT
Angulated drill guide IN GFA
Ø 4.8 AND Ø 4.0 mmPREHENSILE TOOL
Short prehensile tool for Multi-Unit abutment MUWS
MULTI-UNIT PROSTHETIC & SURGICAL INSTRUMENTS
25N.cm
25N.cm
IMPRESSION TAKING COMPONENTS FOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit Pick-up transfer copingSupplied with two green pick-up screws (one short, one long)
MUNT100 (x1)MUNT100-4 (x4)
Narrow Multi-Unit Pop-in transfer coping MUNT200 (x1)MUNT200-4 (x4)
Narrow Multi-Unit Abutment analogSupplied with one MU M1.4 blue screw
MUNA100 (x1)MUNA100-4 (x4)
Composants Référence Visuels
MULTI-UNIT SCREWS FOR Ø 4.8 mm & 4.0 mm MULTI-UNIT ABUTMENTS
MU Black Tite® M1.6 fi nal screwMU M1.6 screw, Blue (x1)MU M1.6 screw, Blue (x4)
OPMU160OPMU161
OPMU161-4
MU Black Tite® M1.4 fi nal screwMU M1.4 screw, Blue
MU140MU141
Multi-Unit Laboratory screw, ShortMulti-Unit Laboratory screw, Long
MUT101MUT102
MULTI-UNIT ADDITIONAL COMPONENTS (all laboratory screws have a “blue“ code)
MULTI-UNIT PROTECTION ANALOGS, Ø 4.8 mm & 4.0 mm
Multi-Unit Protection analog, 4.8 mm(stainless steel)
MUA200 (x1)MUA200-4 (x4)
Multi-Unt Protection analog, 4.0 mm(stainless steel) MUNA200
MULTI-UNIT PROSTHETIC COMPONENTS FOR CAD/CAM RESTORATIONS ON AXIOM® REG/PX
Component Cat. No. Graphics
WAX-UP ACCESSORIESFOR CAD/CAM RESTORATIONS USING Ø 4.8 mm& 4.0 mm MULTI-UNIT ABUTMENTS
Ø 4.8 mm Multi-Unit Wax-upSupplied with one MU M1.4 blue screw
MUWAXUP (x1)MUWAXUP4 (x4)
Ø 4.8 mm Multi-Unit Wax-up and Laboratory screw Supplied with one MU M1.4 blue screw and one long laboratory blue screw
MUWAXUP-S (x1)MUWAXUP-S4 (x4)
Ø 4.0 mm Multi-Unit Wax-upSupplied with one MU M1.4 blue screw
MUNWAXUP (x1)MUNWAXUP4 (x4)
Ø 4.0 mm Multi-Unit Wax-up and Laboratory screw Supplied with one MU M1.4 blue screw and one long laboratory blue screw
MUNWAXUP-S (x1)MUNWAXUP-S4 (x4)
SCAN-ADAPTERS & SCAN-ADAPTER KITS FOR LABORATORY SCANNERS3
Scan-Adapter for Ø 4.8 mm Multi-Unit abutmentSupplied with fi xation screw
151-03-SAO
Scan-Adapter for Ø 4.0 mm Multi-Unit abutmentSupplied with fi xation screw
151-04-SAO
SA TOOL for fi xation of Scan-Adapter ontomaster model
SA TOOL -01
Scan-Adapter Kit for Axiom® REG/PX platforms.Includes 4 SAA1 for Axiom® REG/PX implants, 6 SAO2 for Axiom® REG/PX Ø 4.8 mm Multi-Unit abutments, and dedicated SA Tool (inserter).
151-02-KIT
PACIFIC COMPONENTSFOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit PACIFIC bonding ring Supplied with one MU Black Tite® M1.4 fi nal screw
MUNPAC100
Narrow Multi-Unit PACIFIC analog - Supplied with one MU M1.4 screw and one long laboratory blue screw
MUNPAC110
Narrow Multi-Unit PACIFIC castable copingSupplied with one MU M1.4 laboratory blue screw
MUNPAC120
Narrow Multi-Unit PACIFIC KitIncludes MUNPAC100/110/120
KITMUNPAC -
simeda®
customized &
solutionssolutions
Ø 4.0 mm NARROW MULTI-UNIT AUXILIARY COMPONENTS (“green“ code or “N“)Ø 4.8 MM MULTI-UNIT AUXILIARY COMPONENTS (“yellow“ code)
Axiom® Ø 4.8 mm Multi-Unit Abutments Angulation (ά)Gingival height
(GH)Cat. No. Graphics
Straight abutment (non-indexed)Supplied with a pre-assembled holder
0°
0.75 mm OPMU0-0
1.5 mm OPMU0-1
2.5 mm OPMU0-2
3.5 mm OPMU0-3
4.5 mm OPMU0-4
18° angulated abutment (indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
18°
1.5 mm OPMU18-1 IN
2.5 mm OPMU18-2 IN
3.5 mm OPMU18-3 IN
30° angulated abutment (indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
30°
0.75 mm OPMU30-0 IN
1.5 mm OPMU30-1 IN
2.5 mm OPMU30-2 IN
3.5 mm OPMU30-3 IN
18° angulated abutment (non-indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
18°
1.5 mm OPMU18-1
2.5 mm OPMU18-2
3.5 mm OPMU18-3
30° angulated abutment (non-indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
30°
0.75 mm OPMU30-0
1.5 mm OPMU30-1
2.5 mm OPMU30-2
3.5 mm OPMU30-3
NEW2015
CH = 2.5 mm
GH
Ø = 4.8 mm CH = 2.5 mm
Hmax*GH
Ø = 4.8 mm
ά
**CoCr = Cobalt Chromium.
IMPRESSION TAKING USING Ø 4.8 mm MULTI-UNIT ABUTMENTSPICK-UP technique: open tray orPOP-IN technique: closed tray
Multi-Unit pick-up transfer copingSupplied with two yellow pick-up screws (one short, one long)
MUT100 (x1)MUT100-4 (x4)
Multi-Unit pop-in transfer copingMUT200 (x1)
MUT200-4 (x4)
Multi-Unit abutment analogSupplied with one MU M1.4 blue screw
MUA100 (x1)MUA100-4 (x4)
Instrument Cat. No. Graphics
PROSTHETIC COMPONENTSFOR USE WITH Ø 4.8 mm MULTI-UNIT ABUTMENTS
Multi-Unit protective cap (titanium)
Supplied QMUCAP (x1)
MUCAP-4 (x4)
Multi-Unit titanium temporary copingSupplied with one titanium MU M1.4 screw
MUC100
Multi-Unit PEEK temporary copingSupplied with one titanium MU M1.4 screw
MUC200
Defi nitive Multi-Unit castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUC300
Defi nitive Multi-Unit CoCr** cast-on copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUC400
15N.cm
15N.cm
15N.cm
15N.cm
Manuel
NEW2015
NEW2015
NEW2015
NARROW MULTI-UNIT AUXILIARY COMPONENTS (
HC = 1.5 mm
HG
Ø = 4.0 mmGingival height
(GH)Cat. No. Graphics
0.75 mm OPMUN0-0
1.5 mm OPMUN0-1
2.5 mm OPMUN0-2
3.5 mm OPMUN0-3
4.5 mm OPMUN0-4*NEW2015
NEW2015
15N.cm
15
1-0
3-S
AO
15
1-0
4-S
AO
1 SAA: Scan-Adapter for implant-supported single-unit restorations2 SAO: Scan-Adapter for multiple-unit restorations using conical abutments3 Compatible with Simeda® approved scanners
*Hmax of 18° angled abutments = GH+1.5 mm. Hmax of 30° angled abutments = GH + 2.4 mm.
25N.cm
Black Tite® M1.6fi nal screw OPMU160
SUPPLIEDWITH
GE M U L T I P L E - U N I T S C R E W - R E T A I N E D R E S T O R A T I O N S
H I G H L Y P E R F O R M I N G S O L U T I O N S
MULTI-UNIT AbutmentsGE
Pho
to c
redi
t: A
ntho
gyr
- A
ll ri
ghts
res
erve
d. N
on c
ontr
actu
al p
hoto
s.C1
58_G
B -
201
5-04
ERGONOMIC RANGECOMPREHENSIVE RANGE
A RANGE OF 24 ABUTMENTS!
w 5 Gingival heights: 0.75, 1.5, 2.5, 3.5 and 4.5 mm.
w The 20° morse taper on the platform allowsgreater correction of axial malalignment.
HIGH-PERFORMANCE RANGEINTEGRITY OF AXIOM® ANGULATED MULTI-UNIT ABUTMENTS:Thanks to a unique design, integrity of these screw-retained abutments can be maintained with no trade-off to the wall thickness in critical zones:
The coronal part of the abutment is not truncated in the area that receives the MU M1.4 screw.
The connection system is not truncated at the base of the abutment which accommodates the M1.6 screw.
1
2
Gingival Height (mm) 0.75 1.5 2.5 3.5 4.5
Number of scribe lines
on coronal part0 1 2 3 4
Ø 4.8 mm Multi-Unit Abutments
18°
Angulation
w Angulated abutments (18° and 30°) in both indexed and non-indexed versions.
20° 20° 20°
30°18° or
COMMON PLATFORM
Ø = 4.8 mm
NARROW PLATFORM
Ø = 4.0 mmCOMMON OR NARROW PLATFORMSw Axiom® REG/PX angulated AND straight abutments have
a common Ø 4.8 mm platform and a 2.5 mmcoronal height (CH).Indicated for most multiple-unit screw-retained restorations. Reduced inventory of auxiliary components.
w Axiom® REG/PX straight abutments havea narrow Ø 4.0 mm platform and a reduced 1.5 mmcoronal height (CH).Indicated for multiple-unit screw-retained restorationsin patients with a small inter-implant distance.
EASY HANDLINGw Each abutment comes with its attached holder for easyEach abutment comes with its attached holder for easyEach abutment comes with its attached holder
transfer to the patient’s mouth and safer placement.w Can be used with the angulated drill guide.
QUICK IDENTIFICATIONw Each abutment is laser marked with angulation
(18° or 30°) and gingival height (CH).
EASY MANIPULATIONw Straight abutments have a tapered end which greatly
facilitates insertion.Angulated non indexed abutments feature a repositioning fl at.
w The taper angle on the coronal platform facilitatesplacement of auxiliary components.
ANGULATED DRILL GUIDEfor dental restorations using a limited number of implants
w 30° scribe lines on the drill guide;w 2 mm diameter support tip;w Drill guide height corresponds to tooth height: 10 mm;w Semi-fl exible stainless steel adapts for variances in
anatomy;w Pre-assembled holder assists in achieving parallel
alignment of Multi-Unit abutments.
Anthogyr SAS2 237, Avenue André Lasquin74700 Sallanches - FrancePhone: +33 (0)4 50 58 02 37 Fax: +33 (0)4 50 93 78 60 www.anthogyr.com
FOR ALL PLURAL RESTORATIONSw Partial or complete screw-retained bridges using Multi-Unit straight AND angulated abutments with
a COMMON platform.w Multiple-unit screw-retained restorations using Multi-Unit straight abutments with a NARROW
platform in patients with a small inter-implant distance.
Abutments are supplied Q for immediate loading.Q for immediate loading.Q
Ht 0.75 Ht 1.5 Ht 2.5 Ht 3.5 Ht 4.5
Multiple-UnitScrew-Retained Restorations
GE M U L T I P L E - U N I T S C R E W - R E T A I N E D R E S T O R A T I O N S
H I G H L Y P E R F O R M I N G S O L U T I O N S
MULTI-UNIT AbutmentsGE
Pho
to c
redi
t: A
ntho
gyr
- A
ll ri
ghts
res
erve
d. N
on c
ontr
actu
al p
hoto
s.C1
58_G
B -
201
5-04
ERGONOMIC RANGECOMPREHENSIVE RANGE
A RANGE OF 24 ABUTMENTS!
w 5 Gingival heights: 0.75, 1.5, 2.5, 3.5 and 4.5 mm.
w The 20° morse taper on the platform allowsgreater correction of axial malalignment.
HIGH-PERFORMANCE RANGEINTEGRITY OF AXIOM® ANGULATED MULTI-UNIT ABUTMENTS:Thanks to a unique design, integrity of these screw-retained abutments can be maintained with no trade-off to the wall thickness in critical zones:
The coronal part of the abutment is not truncated in the area that receives the MU M1.4 screw.
The connection system is not truncated at the base of the abutment which accommodates the M1.6 screw.
1
2
Gingival Height (mm) 0.75 1.5 2.5 3.5 4.5
Number of scribe lines
on coronal part0 1 2 3 4
Ø 4.8 mm Multi-Unit Abutments
18°
Angulation
w Angulated abutments (18° and 30°) in both indexed and non-indexed versions.
20° 20° 20°
30°18° or
COMMON PLATFORM
Ø = 4.8 mm
NARROW PLATFORM
Ø = 4.0 mmCOMMON OR NARROW PLATFORMSw Axiom® REG/PX angulated AND straight abutments have
a common Ø 4.8 mm platform and a 2.5 mmcoronal height (CH).Indicated for most multiple-unit screw-retained restorations. Reduced inventory of auxiliary components.
w Axiom® REG/PX straight abutments havea narrow Ø 4.0 mm platform and a reduced 1.5 mmcoronal height (CH).Indicated for multiple-unit screw-retained restorationsin patients with a small inter-implant distance.
EASY HANDLINGw Each abutment comes with its attached holder for easyEach abutment comes with its attached holder for easyEach abutment comes with its attached holder
transfer to the patient’s mouth and safer placement.w Can be used with the angulated drill guide.
QUICK IDENTIFICATIONw Each abutment is laser marked with angulation
(18° or 30°) and gingival height (CH).
EASY MANIPULATIONw Straight abutments have a tapered end which greatly
facilitates insertion.Angulated non indexed abutments feature a repositioning fl at.
w The taper angle on the coronal platform facilitatesplacement of auxiliary components.
ANGULATED DRILL GUIDEfor dental restorations using a limited number of implants
w 30° scribe lines on the drill guide;w 2 mm diameter support tip;w Drill guide height corresponds to tooth height: 10 mm;w Semi-fl exible stainless steel adapts for variances in
anatomy;w Pre-assembled holder assists in achieving parallel
alignment of Multi-Unit abutments.
Anthogyr SAS2 237, Avenue André Lasquin74700 Sallanches - FrancePhone: +33 (0)4 50 58 02 37 Fax: +33 (0)4 50 93 78 60 www.anthogyr.com
FOR ALL PLURAL RESTORATIONSw Partial or complete screw-retained bridges using Multi-Unit straight AND angulated abutments with
a COMMON platform.w Multiple-unit screw-retained restorations using Multi-Unit straight abutments with a NARROW
platform in patients with a small inter-implant distance.
Abutments are supplied Q for immediate loading.Q for immediate loading.Q
Ht 0.75 Ht 1.5 Ht 2.5 Ht 3.5 Ht 4.5
Multiple-UnitScrew-Retained Restorations
GE M U L T I P L E - U N I T S C R E W - R E T A I N E D R E S T O R A T I O N S
GE Ø 4.8 mm MULTI-UNIT RANGEØ 4.8 mm MULTI-UNIT ABUTMENTS
25N.cm
Component Cat. No. Graphics
PROSTHETIC COMPONENTSFOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit protective cap (titanium)Supplied Q MUNCAP
Narrow Multi-Unit temporary coping (titanium)Supplied with one titanium MU M1.4 screw
MUNC100
Narrow Multi-Unit PEEK temporary coping Supplied with one titanium MU M1.4 screw
MUNC200
Narrow Multi-Unit defi nitive castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUNC300
Narrow Multi-Unit CoCr** defi nitive castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUNC400
15N.cm
15N.cm
15N.cm
Manuel
w Used with Axiom® REG/PX implants for multiple-unit or full arch screw-retained restorations.
w Straight AND angulated abutments sharing the same auxiliary components.
w Supplied Q with a pre-assembled holder .
w Auxiliary components have a “yellow“ code.
GE Ø 4.0 mm MULTI-UNIT RANGEØ 4.0 mm NARROW MULTI-UNIT ABUTMENTSw Used with Axiom® REG and Axiom® PX implants for multiple-unit screw-retained restorations in patients with a small
inter-implant distance.w Straight narrow abutments use dedicated auxiliary components.w Supplied Q with a pre-assembled holder .w Auxiliary components have a “green“ code, or are marked «N» for narrow.
25N.cm
Instrument Cat. No. Graphics
TIGHTENING INSTRUMENTS FOR Ø 4.8 mm & 4.0 mm STRAIGHT MULTI-UNIT ABUTMENTS
Multi-Unit mandrel for 4.8 mm and 4.0 mmstraight abutments (short and long)
MUM100 MUM100L
Multi-Unit wrench for 4.8 mm and 4.0 mmstraight abutments
MUW100
SURGICAL INSTRUMENT
Angulated drill guide IN GFA
Ø 4.8 AND Ø 4.0 mmPREHENSILE TOOL
Short prehensile tool for Multi-Unit abutment MUWS
MULTI-UNIT PROSTHETIC & SURGICAL INSTRUMENTS
25N.cm
25N.cm
IMPRESSION TAKING COMPONENTS FOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit Pick-up transfer copingSupplied with two green pick-up screws (one short, one long)
MUNT100 (x1)MUNT100-4 (x4)
Narrow Multi-Unit Pop-in transfer coping MUNT200 (x1)MUNT200-4 (x4)
Narrow Multi-Unit Abutment analogSupplied with one MU M1.4 blue screw
MUNA100 (x1)MUNA100-4 (x4)
Composants Référence Visuels
MULTI-UNIT SCREWS FOR Ø 4.8 mm & 4.0 mm MULTI-UNIT ABUTMENTS
MU Black Tite® M1.6 fi nal screwMU M1.6 screw, Blue (x1)MU M1.6 screw, Blue (x4)
OPMU160OPMU161
OPMU161-4
MU Black Tite® M1.4 fi nal screwMU M1.4 screw, Blue
MU140MU141
Multi-Unit Laboratory screw, ShortMulti-Unit Laboratory screw, Long
MUT101MUT102
MULTI-UNIT ADDITIONAL COMPONENTS (all laboratory screws have a “blue“ code)
MULTI-UNIT PROTECTION ANALOGS, Ø 4.8 mm & 4.0 mm
Multi-Unit Protection analog, 4.8 mm(stainless steel)
MUA200 (x1)MUA200-4 (x4)
Multi-Unt Protection analog, 4.0 mm(stainless steel) MUNA200
MULTI-UNIT PROSTHETIC COMPONENTS FOR CAD/CAM RESTORATIONS ON AXIOM® REG/PX
Component Cat. No. Graphics
WAX-UP ACCESSORIESFOR CAD/CAM RESTORATIONS USING Ø 4.8 mm& 4.0 mm MULTI-UNIT ABUTMENTS
Ø 4.8 mm Multi-Unit Wax-upSupplied with one MU M1.4 blue screw
MUWAXUP (x1)MUWAXUP4 (x4)
Ø 4.8 mm Multi-Unit Wax-up and Laboratory screw Supplied with one MU M1.4 blue screw and one long laboratory blue screw
MUWAXUP-S (x1)MUWAXUP-S4 (x4)
Ø 4.0 mm Multi-Unit Wax-upSupplied with one MU M1.4 blue screw
MUNWAXUP (x1)MUNWAXUP4 (x4)
Ø 4.0 mm Multi-Unit Wax-up and Laboratory screw Supplied with one MU M1.4 blue screw and one long laboratory blue screw
MUNWAXUP-S (x1)MUNWAXUP-S4 (x4)
SCAN-ADAPTERS & SCAN-ADAPTER KITS FOR LABORATORY SCANNERS3
Scan-Adapter for Ø 4.8 mm Multi-Unit abutmentSupplied with fi xation screw
151-03-SAO
Scan-Adapter for Ø 4.0 mm Multi-Unit abutmentSupplied with fi xation screw
151-04-SAO
SA TOOL for fi xation of Scan-Adapter ontomaster model
SA TOOL -01
Scan-Adapter Kit for Axiom® REG/PX platforms.Includes 4 SAA1 for Axiom® REG/PX implants, 6 SAO2 for Axiom® REG/PX Ø 4.8 mm Multi-Unit abutments, and dedicated SA Tool (inserter).
151-02-KIT
PACIFIC COMPONENTSFOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit PACIFIC bonding ring Supplied with one MU Black Tite® M1.4 fi nal screw
MUNPAC100
Narrow Multi-Unit PACIFIC analog - Supplied with one MU M1.4 screw and one long laboratory blue screw
MUNPAC110
Narrow Multi-Unit PACIFIC castable copingSupplied with one MU M1.4 laboratory blue screw
MUNPAC120
Narrow Multi-Unit PACIFIC KitIncludes MUNPAC100/110/120
KITMUNPAC -
simeda®
customized &
solutionssolutions
Ø 4.0 mm NARROW MULTI-UNIT AUXILIARY COMPONENTS (“green“ code or “N“)Ø 4.8 MM MULTI-UNIT AUXILIARY COMPONENTS (“yellow“ code)
Axiom® Ø 4.8 mm Multi-Unit Abutments Angulation (ά)Gingival height
(GH)Cat. No. Graphics
Straight abutment (non-indexed)Supplied with a pre-assembled holder
0°
0.75 mm OPMU0-0
1.5 mm OPMU0-1
2.5 mm OPMU0-2
3.5 mm OPMU0-3
4.5 mm OPMU0-4
18° angulated abutment (indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
18°
1.5 mm OPMU18-1 IN
2.5 mm OPMU18-2 IN
3.5 mm OPMU18-3 IN
30° angulated abutment (indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
30°
0.75 mm OPMU30-0 IN
1.5 mm OPMU30-1 IN
2.5 mm OPMU30-2 IN
3.5 mm OPMU30-3 IN
18° angulated abutment (non-indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
18°
1.5 mm OPMU18-1
2.5 mm OPMU18-2
3.5 mm OPMU18-3
30° angulated abutment (non-indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
30°
0.75 mm OPMU30-0
1.5 mm OPMU30-1
2.5 mm OPMU30-2
3.5 mm OPMU30-3
NEW2015
CH = 2.5 mm
GH
Ø = 4.8 mm CH = 2.5 mm
Hmax*GH
Ø = 4.8 mm
ά
**CoCr = Cobalt Chromium.
IMPRESSION TAKING USING Ø 4.8 mm MULTI-UNIT ABUTMENTSPICK-UP technique: open tray orPOP-IN technique: closed tray
Multi-Unit pick-up transfer copingSupplied with two yellow pick-up screws (one short, one long)
MUT100 (x1)MUT100-4 (x4)
Multi-Unit pop-in transfer copingMUT200 (x1)
MUT200-4 (x4)
Multi-Unit abutment analogSupplied with one MU M1.4 blue screw
MUA100 (x1)MUA100-4 (x4)
Instrument Cat. No. Graphics
PROSTHETIC COMPONENTSFOR USE WITH Ø 4.8 mm MULTI-UNIT ABUTMENTS
Multi-Unit protective cap (titanium)
Supplied QMUCAP (x1)
MUCAP-4 (x4)
Multi-Unit titanium temporary copingSupplied with one titanium MU M1.4 screw
MUC100
Multi-Unit PEEK temporary copingSupplied with one titanium MU M1.4 screw
MUC200
Defi nitive Multi-Unit castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUC300
Defi nitive Multi-Unit CoCr** cast-on copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUC400
15N.cm
15N.cm
15N.cm
15N.cm
Manuel
NEW2015
NEW2015
NEW2015
NARROW MULTI-UNIT AUXILIARY COMPONENTS (
HC = 1.5 mm
HG
Ø = 4.0 mmGingival height
(GH)Cat. No. Graphics
0.75 mm OPMUN0-0
1.5 mm OPMUN0-1
2.5 mm OPMUN0-2
3.5 mm OPMUN0-3
4.5 mm OPMUN0-4*NEW2015
NEW2015
15N.cm
15
1-0
3-S
AO
15
1-0
4-S
AO
1 SAA: Scan-Adapter for implant-supported single-unit restorations2 SAO: Scan-Adapter for multiple-unit restorations using conical abutments3 Compatible with Simeda® approved scanners
*Hmax of 18° angled abutments = GH+1.5 mm. Hmax of 30° angled abutments = GH + 2.4 mm.
25N.cm
Black Tite® M1.6fi nal screw OPMU160
SUPPLIEDWITH
GE M U L T I P L E - U N I T S C R E W - R E T A I N E D R E S T O R A T I O N S
H I G H L Y P E R F O R M I N G S O L U T I O N S
MULTI-UNIT AbutmentsGE
Pho
to c
redi
t: A
ntho
gyr
- A
ll ri
ghts
res
erve
d. N
on c
ontr
actu
al p
hoto
s.C1
58_G
B -
201
5-04
ERGONOMIC RANGECOMPREHENSIVE RANGE
A RANGE OF 24 ABUTMENTS!
w 5 Gingival heights: 0.75, 1.5, 2.5, 3.5 and 4.5 mm.
w The 20° morse taper on the platform allowsgreater correction of axial malalignment.
HIGH-PERFORMANCE RANGEINTEGRITY OF AXIOM® ANGULATED MULTI-UNIT ABUTMENTS:Thanks to a unique design, integrity of these screw-retained abutments can be maintained with no trade-off to the wall thickness in critical zones:
The coronal part of the abutment is not truncated in the area that receives the MU M1.4 screw.
The connection system is not truncated at the base of the abutment which accommodates the M1.6 screw.
1
2
Gingival Height (mm) 0.75 1.5 2.5 3.5 4.5
Number of scribe lines
on coronal part0 1 2 3 4
Ø 4.8 mm Multi-Unit Abutments
18°
Angulation
w Angulated abutments (18° and 30°) in both indexed and non-indexed versions.
20° 20° 20°
30°18° or
COMMON PLATFORM
Ø = 4.8 mm
NARROW PLATFORM
Ø = 4.0 mmCOMMON OR NARROW PLATFORMSw Axiom® REG/PX angulated AND straight abutments have
a common Ø 4.8 mm platform and a 2.5 mmcoronal height (CH).Indicated for most multiple-unit screw-retained restorations. Reduced inventory of auxiliary components.
w Axiom® REG/PX straight abutments havea narrow Ø 4.0 mm platform and a reduced 1.5 mmcoronal height (CH).Indicated for multiple-unit screw-retained restorationsin patients with a small inter-implant distance.
EASY HANDLINGw Each abutment comes with its attached holder for easyEach abutment comes with its attached holder for easyEach abutment comes with its attached holder
transfer to the patient’s mouth and safer placement.w Can be used with the angulated drill guide.
QUICK IDENTIFICATIONw Each abutment is laser marked with angulation
(18° or 30°) and gingival height (CH).
EASY MANIPULATIONw Straight abutments have a tapered end which greatly
facilitates insertion.Angulated non indexed abutments feature a repositioning fl at.
w The taper angle on the coronal platform facilitatesplacement of auxiliary components.
ANGULATED DRILL GUIDEfor dental restorations using a limited number of implants
w 30° scribe lines on the drill guide;w 2 mm diameter support tip;w Drill guide height corresponds to tooth height: 10 mm;w Semi-fl exible stainless steel adapts for variances in
anatomy;w Pre-assembled holder assists in achieving parallel
alignment of Multi-Unit abutments.
Anthogyr SAS2 237, Avenue André Lasquin74700 Sallanches - FrancePhone: +33 (0)4 50 58 02 37 Fax: +33 (0)4 50 93 78 60 www.anthogyr.com
FOR ALL PLURAL RESTORATIONSw Partial or complete screw-retained bridges using Multi-Unit straight AND angulated abutments with
a COMMON platform.w Multiple-unit screw-retained restorations using Multi-Unit straight abutments with a NARROW
platform in patients with a small inter-implant distance.
Abutments are supplied Q for immediate loading.Q for immediate loading.Q
Ht 0.75 Ht 1.5 Ht 2.5 Ht 3.5 Ht 4.5
Multiple-UnitScrew-Retained Restorations
GE M U L T I P L E - U N I T S C R E W - R E T A I N E D R E S T O R A T I O N S
GE Ø 4.8 mm MULTI-UNIT RANGEØ 4.8 mm MULTI-UNIT ABUTMENTS
25N.cm
Component Cat. No. Graphics
PROSTHETIC COMPONENTSFOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit protective cap (titanium)Supplied Q MUNCAP
Narrow Multi-Unit temporary coping (titanium)Supplied with one titanium MU M1.4 screw
MUNC100
Narrow Multi-Unit PEEK temporary coping Supplied with one titanium MU M1.4 screw
MUNC200
Narrow Multi-Unit defi nitive castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUNC300
Narrow Multi-Unit CoCr** defi nitive castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUNC400
15N.cm
15N.cm
15N.cm
Manuel
w Used with Axiom® REG/PX implants for multiple-unit or full arch screw-retained restorations.
w Straight AND angulated abutments sharing the same auxiliary components.
w Supplied Q with a pre-assembled holder .
w Auxiliary components have a “yellow“ code.
GE Ø 4.0 mm MULTI-UNIT RANGEØ 4.0 mm NARROW MULTI-UNIT ABUTMENTSw Used with Axiom® REG and Axiom® PX implants for multiple-unit screw-retained restorations in patients with a small
inter-implant distance.w Straight narrow abutments use dedicated auxiliary components.w Supplied Q with a pre-assembled holder .w Auxiliary components have a “green“ code, or are marked «N» for narrow.
25N.cm
Instrument Cat. No. Graphics
TIGHTENING INSTRUMENTS FOR Ø 4.8 mm & 4.0 mm STRAIGHT MULTI-UNIT ABUTMENTS
Multi-Unit mandrel for 4.8 mm and 4.0 mmstraight abutments (short and long)
MUM100 MUM100L
Multi-Unit wrench for 4.8 mm and 4.0 mmstraight abutments
MUW100
SURGICAL INSTRUMENT
Angulated drill guide IN GFA
Ø 4.8 AND Ø 4.0 mmPREHENSILE TOOL
Short prehensile tool for Multi-Unit abutment MUWS
MULTI-UNIT PROSTHETIC & SURGICAL INSTRUMENTS
25N.cm
25N.cm
IMPRESSION TAKING COMPONENTS FOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit Pick-up transfer copingSupplied with two green pick-up screws (one short, one long)
MUNT100 (x1)MUNT100-4 (x4)
Narrow Multi-Unit Pop-in transfer coping MUNT200 (x1)MUNT200-4 (x4)
Narrow Multi-Unit Abutment analogSupplied with one MU M1.4 blue screw
MUNA100 (x1)MUNA100-4 (x4)
Composants Référence Visuels
MULTI-UNIT SCREWS FOR Ø 4.8 mm & 4.0 mm MULTI-UNIT ABUTMENTS
MU Black Tite® M1.6 fi nal screwMU M1.6 screw, Blue (x1)MU M1.6 screw, Blue (x4)
OPMU160OPMU161
OPMU161-4
MU Black Tite® M1.4 fi nal screwMU M1.4 screw, Blue
MU140MU141
Multi-Unit Laboratory screw, ShortMulti-Unit Laboratory screw, Long
MUT101MUT102
MULTI-UNIT ADDITIONAL COMPONENTS (all laboratory screws have a “blue“ code)
MULTI-UNIT PROTECTION ANALOGS, Ø 4.8 mm & 4.0 mm
Multi-Unit Protection analog, 4.8 mm(stainless steel)
MUA200 (x1)MUA200-4 (x4)
Multi-Unt Protection analog, 4.0 mm(stainless steel) MUNA200
MULTI-UNIT PROSTHETIC COMPONENTS FOR CAD/CAM RESTORATIONS ON AXIOM® REG/PX
Component Cat. No. Graphics
WAX-UP ACCESSORIESFOR CAD/CAM RESTORATIONS USING Ø 4.8 mm& 4.0 mm MULTI-UNIT ABUTMENTS
Ø 4.8 mm Multi-Unit Wax-upSupplied with one MU M1.4 blue screw
MUWAXUP (x1)MUWAXUP4 (x4)
Ø 4.8 mm Multi-Unit Wax-up and Laboratory screw Supplied with one MU M1.4 blue screw and one long laboratory blue screw
MUWAXUP-S (x1)MUWAXUP-S4 (x4)
Ø 4.0 mm Multi-Unit Wax-upSupplied with one MU M1.4 blue screw
MUNWAXUP (x1)MUNWAXUP4 (x4)
Ø 4.0 mm Multi-Unit Wax-up and Laboratory screw Supplied with one MU M1.4 blue screw and one long laboratory blue screw
MUNWAXUP-S (x1)MUNWAXUP-S4 (x4)
SCAN-ADAPTERS & SCAN-ADAPTER KITS FOR LABORATORY SCANNERS3
Scan-Adapter for Ø 4.8 mm Multi-Unit abutmentSupplied with fi xation screw
151-03-SAO
Scan-Adapter for Ø 4.0 mm Multi-Unit abutmentSupplied with fi xation screw
151-04-SAO
SA TOOL for fi xation of Scan-Adapter ontomaster model
SA TOOL -01
Scan-Adapter Kit for Axiom® REG/PX platforms.Includes 4 SAA1 for Axiom® REG/PX implants, 6 SAO2 for Axiom® REG/PX Ø 4.8 mm Multi-Unit abutments, and dedicated SA Tool (inserter).
151-02-KIT
PACIFIC COMPONENTSFOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit PACIFIC bonding ring Supplied with one MU Black Tite® M1.4 fi nal screw
MUNPAC100
Narrow Multi-Unit PACIFIC analog - Supplied with one MU M1.4 screw and one long laboratory blue screw
MUNPAC110
Narrow Multi-Unit PACIFIC castable copingSupplied with one MU M1.4 laboratory blue screw
MUNPAC120
Narrow Multi-Unit PACIFIC KitIncludes MUNPAC100/110/120
KITMUNPAC -
simeda®
customized &
solutionssolutions
Ø 4.0 mm NARROW MULTI-UNIT AUXILIARY COMPONENTS (“green“ code or “N“)Ø 4.8 MM MULTI-UNIT AUXILIARY COMPONENTS (“yellow“ code)
Axiom® Ø 4.8 mm Multi-Unit Abutments Angulation (ά)Gingival height
(GH)Cat. No. Graphics
Straight abutment (non-indexed)Supplied with a pre-assembled holder
0°
0.75 mm OPMU0-0
1.5 mm OPMU0-1
2.5 mm OPMU0-2
3.5 mm OPMU0-3
4.5 mm OPMU0-4
18° angulated abutment (indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
18°
1.5 mm OPMU18-1 IN
2.5 mm OPMU18-2 IN
3.5 mm OPMU18-3 IN
30° angulated abutment (indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
30°
0.75 mm OPMU30-0 IN
1.5 mm OPMU30-1 IN
2.5 mm OPMU30-2 IN
3.5 mm OPMU30-3 IN
18° angulated abutment (non-indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
18°
1.5 mm OPMU18-1
2.5 mm OPMU18-2
3.5 mm OPMU18-3
30° angulated abutment (non-indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
30°
0.75 mm OPMU30-0
1.5 mm OPMU30-1
2.5 mm OPMU30-2
3.5 mm OPMU30-3
NEW2015
CH = 2.5 mm
GH
Ø = 4.8 mm CH = 2.5 mm
Hmax*GH
Ø = 4.8 mm
ά
**CoCr = Cobalt Chromium.
IMPRESSION TAKING USING Ø 4.8 mm MULTI-UNIT ABUTMENTSPICK-UP technique: open tray orPOP-IN technique: closed tray
Multi-Unit pick-up transfer copingSupplied with two yellow pick-up screws (one short, one long)
MUT100 (x1)MUT100-4 (x4)
Multi-Unit pop-in transfer copingMUT200 (x1)
MUT200-4 (x4)
Multi-Unit abutment analogSupplied with one MU M1.4 blue screw
MUA100 (x1)MUA100-4 (x4)
Instrument Cat. No. Graphics
PROSTHETIC COMPONENTSFOR USE WITH Ø 4.8 mm MULTI-UNIT ABUTMENTS
Multi-Unit protective cap (titanium)
Supplied QMUCAP (x1)
MUCAP-4 (x4)
Multi-Unit titanium temporary copingSupplied with one titanium MU M1.4 screw
MUC100
Multi-Unit PEEK temporary copingSupplied with one titanium MU M1.4 screw
MUC200
Defi nitive Multi-Unit castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUC300
Defi nitive Multi-Unit CoCr** cast-on copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUC400
15N.cm
15N.cm
15N.cm
15N.cm
Manuel
NEW2015
NEW2015
NEW2015
NARROW MULTI-UNIT AUXILIARY COMPONENTS (
HC = 1.5 mm
HG
Ø = 4.0 mmGingival height
(GH)Cat. No. Graphics
0.75 mm OPMUN0-0
1.5 mm OPMUN0-1
2.5 mm OPMUN0-2
3.5 mm OPMUN0-3
4.5 mm OPMUN0-4*NEW2015
NEW2015
15N.cm
15
1-0
3-S
AO
15
1-0
4-S
AO
1 SAA: Scan-Adapter for implant-supported single-unit restorations2 SAO: Scan-Adapter for multiple-unit restorations using conical abutments3 Compatible with Simeda® approved scanners
*Hmax of 18° angled abutments = GH+1.5 mm. Hmax of 30° angled abutments = GH + 2.4 mm.
25N.cm
Black Tite® M1.6fi nal screw OPMU160
SUPPLIEDWITH
GE M U L T I P L E - U N I T S C R E W - R E T A I N E D R E S T O R A T I O N S
H I G H L Y P E R F O R M I N G S O L U T I O N S
MULTI-UNIT AbutmentsGE
Pho
to c
redi
t: A
ntho
gyr
- A
ll ri
ghts
res
erve
d. N
on c
ontr
actu
al p
hoto
s.C1
58_G
B -
201
5-04
ERGONOMIC RANGECOMPREHENSIVE RANGE
A RANGE OF 24 ABUTMENTS!
w 5 Gingival heights: 0.75, 1.5, 2.5, 3.5 and 4.5 mm.
w The 20° morse taper on the platform allowsgreater correction of axial malalignment.
HIGH-PERFORMANCE RANGEINTEGRITY OF AXIOM® ANGULATED MULTI-UNIT ABUTMENTS:Thanks to a unique design, integrity of these screw-retained abutments can be maintained with no trade-off to the wall thickness in critical zones:
The coronal part of the abutment is not truncated in the area that receives the MU M1.4 screw.
The connection system is not truncated at the base of the abutment which accommodates the M1.6 screw.
1
2
Gingival Height (mm) 0.75 1.5 2.5 3.5 4.5
Number of scribe lines
on coronal part0 1 2 3 4
Ø 4.8 mm Multi-Unit Abutments
18°
Angulation
w Angulated abutments (18° and 30°) in both indexed and non-indexed versions.
20° 20° 20°
30°18° or
COMMON PLATFORM
Ø = 4.8 mm
NARROW PLATFORM
Ø = 4.0 mmCOMMON OR NARROW PLATFORMSw Axiom® REG/PX angulated AND straight abutments have
a common Ø 4.8 mm platform and a 2.5 mmcoronal height (CH).Indicated for most multiple-unit screw-retained restorations. Reduced inventory of auxiliary components.
w Axiom® REG/PX straight abutments havea narrow Ø 4.0 mm platform and a reduced 1.5 mmcoronal height (CH).Indicated for multiple-unit screw-retained restorationsin patients with a small inter-implant distance.
EASY HANDLINGw Each abutment comes with its attached holder for easyEach abutment comes with its attached holder for easyEach abutment comes with its attached holder
transfer to the patient’s mouth and safer placement.w Can be used with the angulated drill guide.
QUICK IDENTIFICATIONw Each abutment is laser marked with angulation
(18° or 30°) and gingival height (CH).
EASY MANIPULATIONw Straight abutments have a tapered end which greatly
facilitates insertion.Angulated non indexed abutments feature a repositioning fl at.
w The taper angle on the coronal platform facilitatesplacement of auxiliary components.
ANGULATED DRILL GUIDEfor dental restorations using a limited number of implants
w 30° scribe lines on the drill guide;w 2 mm diameter support tip;w Drill guide height corresponds to tooth height: 10 mm;w Semi-fl exible stainless steel adapts for variances in
anatomy;w Pre-assembled holder assists in achieving parallel
alignment of Multi-Unit abutments.
Anthogyr SAS2 237, Avenue André Lasquin74700 Sallanches - FrancePhone: +33 (0)4 50 58 02 37 Fax: +33 (0)4 50 93 78 60 www.anthogyr.com
FOR ALL PLURAL RESTORATIONSw Partial or complete screw-retained bridges using Multi-Unit straight AND angulated abutments with
a COMMON platform.w Multiple-unit screw-retained restorations using Multi-Unit straight abutments with a NARROW
platform in patients with a small inter-implant distance.
Abutments are supplied Q for immediate loading.Q for immediate loading.Q
Ht 0.75 Ht 1.5 Ht 2.5 Ht 3.5 Ht 4.5
Multiple-UnitScrew-Retained Restorations
GE M U L T I P L E - U N I T S C R E W - R E T A I N E D R E S T O R A T I O N S
GE Ø 4.8 mm MULTI-UNIT RANGEØ 4.8 mm MULTI-UNIT ABUTMENTS
25N.cm
Component Cat. No. Graphics
PROSTHETIC COMPONENTSFOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit protective cap (titanium)Supplied Q MUNCAP
Narrow Multi-Unit temporary coping (titanium)Supplied with one titanium MU M1.4 screw
MUNC100
Narrow Multi-Unit PEEK temporary coping Supplied with one titanium MU M1.4 screw
MUNC200
Narrow Multi-Unit defi nitive castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUNC300
Narrow Multi-Unit CoCr** defi nitive castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUNC400
15N.cm
15N.cm
15N.cm
Manuel
w Used with Axiom® REG/PX implants for multiple-unit or full arch screw-retained restorations.
w Straight AND angulated abutments sharing the same auxiliary components.
w Supplied Q with a pre-assembled holder .
w Auxiliary components have a “yellow“ code.
GE Ø 4.0 mm MULTI-UNIT RANGEØ 4.0 mm NARROW MULTI-UNIT ABUTMENTSw Used with Axiom® REG and Axiom® PX implants for multiple-unit screw-retained restorations in patients with a small
inter-implant distance.w Straight narrow abutments use dedicated auxiliary components.w Supplied Q with a pre-assembled holder .w Auxiliary components have a “green“ code, or are marked «N» for narrow.
25N.cm
Instrument Cat. No. Graphics
TIGHTENING INSTRUMENTS FOR Ø 4.8 mm & 4.0 mm STRAIGHT MULTI-UNIT ABUTMENTS
Multi-Unit mandrel for 4.8 mm and 4.0 mmstraight abutments (short and long)
MUM100 MUM100L
Multi-Unit wrench for 4.8 mm and 4.0 mmstraight abutments
MUW100
SURGICAL INSTRUMENT
Angulated drill guide IN GFA
Ø 4.8 AND Ø 4.0 mmPREHENSILE TOOL
Short prehensile tool for Multi-Unit abutment MUWS
MULTI-UNIT PROSTHETIC & SURGICAL INSTRUMENTS
25N.cm
25N.cm
IMPRESSION TAKING COMPONENTS FOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit Pick-up transfer copingSupplied with two green pick-up screws (one short, one long)
MUNT100 (x1)MUNT100-4 (x4)
Narrow Multi-Unit Pop-in transfer coping MUNT200 (x1)MUNT200-4 (x4)
Narrow Multi-Unit Abutment analogSupplied with one MU M1.4 blue screw
MUNA100 (x1)MUNA100-4 (x4)
Composants Référence Visuels
MULTI-UNIT SCREWS FOR Ø 4.8 mm & 4.0 mm MULTI-UNIT ABUTMENTS
MU Black Tite® M1.6 fi nal screwMU M1.6 screw, Blue (x1)MU M1.6 screw, Blue (x4)
OPMU160OPMU161
OPMU161-4
MU Black Tite® M1.4 fi nal screwMU M1.4 screw, Blue
MU140MU141
Multi-Unit Laboratory screw, ShortMulti-Unit Laboratory screw, Long
MUT101MUT102
MULTI-UNIT ADDITIONAL COMPONENTS (all laboratory screws have a “blue“ code)
MULTI-UNIT PROTECTION ANALOGS, Ø 4.8 mm & 4.0 mm
Multi-Unit Protection analog, 4.8 mm(stainless steel)
MUA200 (x1)MUA200-4 (x4)
Multi-Unt Protection analog, 4.0 mm(stainless steel) MUNA200
MULTI-UNIT PROSTHETIC COMPONENTS FOR CAD/CAM RESTORATIONS ON AXIOM® REG/PX
Component Cat. No. Graphics
WAX-UP ACCESSORIESFOR CAD/CAM RESTORATIONS USING Ø 4.8 mm& 4.0 mm MULTI-UNIT ABUTMENTS
Ø 4.8 mm Multi-Unit Wax-upSupplied with one MU M1.4 blue screw
MUWAXUP (x1)MUWAXUP4 (x4)
Ø 4.8 mm Multi-Unit Wax-up and Laboratory screw Supplied with one MU M1.4 blue screw and one long laboratory blue screw
MUWAXUP-S (x1)MUWAXUP-S4 (x4)
Ø 4.0 mm Multi-Unit Wax-upSupplied with one MU M1.4 blue screw
MUNWAXUP (x1)MUNWAXUP4 (x4)
Ø 4.0 mm Multi-Unit Wax-up and Laboratory screw Supplied with one MU M1.4 blue screw and one long laboratory blue screw
MUNWAXUP-S (x1)MUNWAXUP-S4 (x4)
SCAN-ADAPTERS & SCAN-ADAPTER KITS FOR LABORATORY SCANNERS3
Scan-Adapter for Ø 4.8 mm Multi-Unit abutmentSupplied with fi xation screw
151-03-SAO
Scan-Adapter for Ø 4.0 mm Multi-Unit abutmentSupplied with fi xation screw
151-04-SAO
SA TOOL for fi xation of Scan-Adapter ontomaster model
SA TOOL -01
Scan-Adapter Kit for Axiom® REG/PX platforms.Includes 4 SAA1 for Axiom® REG/PX implants, 6 SAO2 for Axiom® REG/PX Ø 4.8 mm Multi-Unit abutments, and dedicated SA Tool (inserter).
151-02-KIT
PACIFIC COMPONENTSFOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit PACIFIC bonding ring Supplied with one MU Black Tite® M1.4 fi nal screw
MUNPAC100
Narrow Multi-Unit PACIFIC analog - Supplied with one MU M1.4 screw and one long laboratory blue screw
MUNPAC110
Narrow Multi-Unit PACIFIC castable copingSupplied with one MU M1.4 laboratory blue screw
MUNPAC120
Narrow Multi-Unit PACIFIC KitIncludes MUNPAC100/110/120
KITMUNPAC -
simeda®
customized &
solutionssolutions
Ø 4.0 mm NARROW MULTI-UNIT AUXILIARY COMPONENTS (“green“ code or “N“)Ø 4.8 MM MULTI-UNIT AUXILIARY COMPONENTS (“yellow“ code)
Axiom® Ø 4.8 mm Multi-Unit Abutments Angulation (ά)Gingival height
(GH)Cat. No. Graphics
Straight abutment (non-indexed)Supplied with a pre-assembled holder
0°
0.75 mm OPMU0-0
1.5 mm OPMU0-1
2.5 mm OPMU0-2
3.5 mm OPMU0-3
4.5 mm OPMU0-4
18° angulated abutment (indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
18°
1.5 mm OPMU18-1 IN
2.5 mm OPMU18-2 IN
3.5 mm OPMU18-3 IN
30° angulated abutment (indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
30°
0.75 mm OPMU30-0 IN
1.5 mm OPMU30-1 IN
2.5 mm OPMU30-2 IN
3.5 mm OPMU30-3 IN
18° angulated abutment (non-indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
18°
1.5 mm OPMU18-1
2.5 mm OPMU18-2
3.5 mm OPMU18-3
30° angulated abutment (non-indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
30°
0.75 mm OPMU30-0
1.5 mm OPMU30-1
2.5 mm OPMU30-2
3.5 mm OPMU30-3
NEW2015
CH = 2.5 mm
GH
Ø = 4.8 mm CH = 2.5 mm
Hmax*GH
Ø = 4.8 mm
ά
**CoCr = Cobalt Chromium.
IMPRESSION TAKING USING Ø 4.8 mm MULTI-UNIT ABUTMENTSPICK-UP technique: open tray orPOP-IN technique: closed tray
Multi-Unit pick-up transfer copingSupplied with two yellow pick-up screws (one short, one long)
MUT100 (x1)MUT100-4 (x4)
Multi-Unit pop-in transfer copingMUT200 (x1)
MUT200-4 (x4)
Multi-Unit abutment analogSupplied with one MU M1.4 blue screw
MUA100 (x1)MUA100-4 (x4)
Instrument Cat. No. Graphics
PROSTHETIC COMPONENTSFOR USE WITH Ø 4.8 mm MULTI-UNIT ABUTMENTS
Multi-Unit protective cap (titanium)
Supplied QMUCAP (x1)
MUCAP-4 (x4)
Multi-Unit titanium temporary copingSupplied with one titanium MU M1.4 screw
MUC100
Multi-Unit PEEK temporary copingSupplied with one titanium MU M1.4 screw
MUC200
Defi nitive Multi-Unit castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUC300
Defi nitive Multi-Unit CoCr** cast-on copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUC400
15N.cm
15N.cm
15N.cm
15N.cm
Manuel
NEW2015
NEW2015
NEW2015
NARROW MULTI-UNIT AUXILIARY COMPONENTS (
HC = 1.5 mm
HG
Ø = 4.0 mmGingival height
(GH)Cat. No. Graphics
0.75 mm OPMUN0-0
1.5 mm OPMUN0-1
2.5 mm OPMUN0-2
3.5 mm OPMUN0-3
4.5 mm OPMUN0-4*NEW2015
NEW2015
15N.cm
15
1-0
3-S
AO
15
1-0
4-S
AO
1 SAA: Scan-Adapter for implant-supported single-unit restorations2 SAO: Scan-Adapter for multiple-unit restorations using conical abutments3 Compatible with Simeda® approved scanners
*Hmax of 18° angled abutments = GH+1.5 mm. Hmax of 30° angled abutments = GH + 2.4 mm.
25N.cm
Black Tite® M1.6fi nal screw OPMU160
SUPPLIEDWITH
GE M U L T I P L E - U N I T S C R E W - R E T A I N E D R E S T O R A T I O N S
H I G H L Y P E R F O R M I N G S O L U T I O N S
MULTI-UNIT AbutmentsGE
Pho
to c
redi
t: A
ntho
gyr
- A
ll ri
ghts
res
erve
d. N
on c
ontr
actu
al p
hoto
s.C1
58_G
B -
201
5-04
ERGONOMIC RANGECOMPREHENSIVE RANGE
A RANGE OF 24 ABUTMENTS!
w 5 Gingival heights: 0.75, 1.5, 2.5, 3.5 and 4.5 mm.
w The 20° morse taper on the platform allowsgreater correction of axial malalignment.
HIGH-PERFORMANCE RANGEINTEGRITY OF AXIOM® ANGULATED MULTI-UNIT ABUTMENTS:Thanks to a unique design, integrity of these screw-retained abutments can be maintained with no trade-off to the wall thickness in critical zones:
The coronal part of the abutment is not truncated in the area that receives the MU M1.4 screw.
The connection system is not truncated at the base of the abutment which accommodates the M1.6 screw.
1
2
Gingival Height (mm) 0.75 1.5 2.5 3.5 4.5
Number of scribe lines
on coronal part0 1 2 3 4
Ø 4.8 mm Multi-Unit Abutments
18°
Angulation
w Angulated abutments (18° and 30°) in both indexed and non-indexed versions.
20° 20° 20°
30°18° or
COMMON PLATFORM
Ø = 4.8 mm
NARROW PLATFORM
Ø = 4.0 mmCOMMON OR NARROW PLATFORMSw Axiom® REG/PX angulated AND straight abutments have
a common Ø 4.8 mm platform and a 2.5 mmcoronal height (CH).Indicated for most multiple-unit screw-retained restorations. Reduced inventory of auxiliary components.
w Axiom® REG/PX straight abutments havea narrow Ø 4.0 mm platform and a reduced 1.5 mmcoronal height (CH).Indicated for multiple-unit screw-retained restorationsin patients with a small inter-implant distance.
EASY HANDLINGw Each abutment comes with its attached holder for easyEach abutment comes with its attached holder for easyEach abutment comes with its attached holder
transfer to the patient’s mouth and safer placement.w Can be used with the angulated drill guide.
QUICK IDENTIFICATIONw Each abutment is laser marked with angulation
(18° or 30°) and gingival height (CH).
EASY MANIPULATIONw Straight abutments have a tapered end which greatly
facilitates insertion.Angulated non indexed abutments feature a repositioning fl at.
w The taper angle on the coronal platform facilitatesplacement of auxiliary components.
ANGULATED DRILL GUIDEfor dental restorations using a limited number of implants
w 30° scribe lines on the drill guide;w 2 mm diameter support tip;w Drill guide height corresponds to tooth height: 10 mm;w Semi-fl exible stainless steel adapts for variances in
anatomy;w Pre-assembled holder assists in achieving parallel
alignment of Multi-Unit abutments.
Anthogyr SAS2 237, Avenue André Lasquin74700 Sallanches - FrancePhone: +33 (0)4 50 58 02 37 Fax: +33 (0)4 50 93 78 60 www.anthogyr.com
FOR ALL PLURAL RESTORATIONSw Partial or complete screw-retained bridges using Multi-Unit straight AND angulated abutments with
a COMMON platform.w Multiple-unit screw-retained restorations using Multi-Unit straight abutments with a NARROW
platform in patients with a small inter-implant distance.
Abutments are supplied Q for immediate loading.Q for immediate loading.Q
Ht 0.75 Ht 1.5 Ht 2.5 Ht 3.5 Ht 4.5
Multiple-UnitScrew-Retained Restorations
GE M U L T I P L E - U N I T S C R E W - R E T A I N E D R E S T O R A T I O N S
GE Ø 4.8 mm MULTI-UNIT RANGEØ 4.8 mm MULTI-UNIT ABUTMENTS
25N.cm
Component Cat. No. Graphics
PROSTHETIC COMPONENTSFOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit protective cap (titanium)Supplied Q MUNCAP
Narrow Multi-Unit temporary coping (titanium)Supplied with one titanium MU M1.4 screw
MUNC100
Narrow Multi-Unit PEEK temporary coping Supplied with one titanium MU M1.4 screw
MUNC200
Narrow Multi-Unit defi nitive castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUNC300
Narrow Multi-Unit CoCr** defi nitive castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUNC400
15N.cm
15N.cm
15N.cm
Manuel
w Used with Axiom® REG/PX implants for multiple-unit or full arch screw-retained restorations.
w Straight AND angulated abutments sharing the same auxiliary components.
w Supplied Q with a pre-assembled holder .
w Auxiliary components have a “yellow“ code.
GE Ø 4.0 mm MULTI-UNIT RANGEØ 4.0 mm NARROW MULTI-UNIT ABUTMENTSw Used with Axiom® REG and Axiom® PX implants for multiple-unit screw-retained restorations in patients with a small
inter-implant distance.w Straight narrow abutments use dedicated auxiliary components.w Supplied Q with a pre-assembled holder .w Auxiliary components have a “green“ code, or are marked «N» for narrow.
25N.cm
Instrument Cat. No. Graphics
TIGHTENING INSTRUMENTS FOR Ø 4.8 mm & 4.0 mm STRAIGHT MULTI-UNIT ABUTMENTS
Multi-Unit mandrel for 4.8 mm and 4.0 mmstraight abutments (short and long)
MUM100 MUM100L
Multi-Unit wrench for 4.8 mm and 4.0 mmstraight abutments
MUW100
SURGICAL INSTRUMENT
Angulated drill guide IN GFA
Ø 4.8 AND Ø 4.0 mmPREHENSILE TOOL
Short prehensile tool for Multi-Unit abutment MUWS
MULTI-UNIT PROSTHETIC & SURGICAL INSTRUMENTS
25N.cm
25N.cm
IMPRESSION TAKING COMPONENTS FOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit Pick-up transfer copingSupplied with two green pick-up screws (one short, one long)
MUNT100 (x1)MUNT100-4 (x4)
Narrow Multi-Unit Pop-in transfer coping MUNT200 (x1)MUNT200-4 (x4)
Narrow Multi-Unit Abutment analogSupplied with one MU M1.4 blue screw
MUNA100 (x1)MUNA100-4 (x4)
Composants Référence Visuels
MULTI-UNIT SCREWS FOR Ø 4.8 mm & 4.0 mm MULTI-UNIT ABUTMENTS
MU Black Tite® M1.6 fi nal screwMU M1.6 screw, Blue (x1)MU M1.6 screw, Blue (x4)
OPMU160OPMU161
OPMU161-4
MU Black Tite® M1.4 fi nal screwMU M1.4 screw, Blue
MU140MU141
Multi-Unit Laboratory screw, ShortMulti-Unit Laboratory screw, Long
MUT101MUT102
MULTI-UNIT ADDITIONAL COMPONENTS (all laboratory screws have a “blue“ code)
MULTI-UNIT PROTECTION ANALOGS, Ø 4.8 mm & 4.0 mm
Multi-Unit Protection analog, 4.8 mm(stainless steel)
MUA200 (x1)MUA200-4 (x4)
Multi-Unt Protection analog, 4.0 mm(stainless steel) MUNA200
MULTI-UNIT PROSTHETIC COMPONENTS FOR CAD/CAM RESTORATIONS ON AXIOM® REG/PX
Component Cat. No. Graphics
WAX-UP ACCESSORIESFOR CAD/CAM RESTORATIONS USING Ø 4.8 mm& 4.0 mm MULTI-UNIT ABUTMENTS
Ø 4.8 mm Multi-Unit Wax-upSupplied with one MU M1.4 blue screw
MUWAXUP (x1)MUWAXUP4 (x4)
Ø 4.8 mm Multi-Unit Wax-up and Laboratory screw Supplied with one MU M1.4 blue screw and one long laboratory blue screw
MUWAXUP-S (x1)MUWAXUP-S4 (x4)
Ø 4.0 mm Multi-Unit Wax-upSupplied with one MU M1.4 blue screw
MUNWAXUP (x1)MUNWAXUP4 (x4)
Ø 4.0 mm Multi-Unit Wax-up and Laboratory screw Supplied with one MU M1.4 blue screw and one long laboratory blue screw
MUNWAXUP-S (x1)MUNWAXUP-S4 (x4)
SCAN-ADAPTERS & SCAN-ADAPTER KITS FOR LABORATORY SCANNERS3
Scan-Adapter for Ø 4.8 mm Multi-Unit abutmentSupplied with fi xation screw
151-03-SAO
Scan-Adapter for Ø 4.0 mm Multi-Unit abutmentSupplied with fi xation screw
151-04-SAO
SA TOOL for fi xation of Scan-Adapter ontomaster model
SA TOOL -01
Scan-Adapter Kit for Axiom® REG/PX platforms.Includes 4 SAA1 for Axiom® REG/PX implants, 6 SAO2 for Axiom® REG/PX Ø 4.8 mm Multi-Unit abutments, and dedicated SA Tool (inserter).
151-02-KIT
PACIFIC COMPONENTSFOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit PACIFIC bonding ring Supplied with one MU Black Tite® M1.4 fi nal screw
MUNPAC100
Narrow Multi-Unit PACIFIC analog - Supplied with one MU M1.4 screw and one long laboratory blue screw
MUNPAC110
Narrow Multi-Unit PACIFIC castable copingSupplied with one MU M1.4 laboratory blue screw
MUNPAC120
Narrow Multi-Unit PACIFIC KitIncludes MUNPAC100/110/120
KITMUNPAC -
simeda®
customized &
solutionssolutions
Ø 4.0 mm NARROW MULTI-UNIT AUXILIARY COMPONENTS (“green“ code or “N“)Ø 4.8 MM MULTI-UNIT AUXILIARY COMPONENTS (“yellow“ code)
Axiom® Ø 4.8 mm Multi-Unit Abutments Angulation (ά)Gingival height
(GH)Cat. No. Graphics
Straight abutment (non-indexed)Supplied with a pre-assembled holder
0°
0.75 mm OPMU0-0
1.5 mm OPMU0-1
2.5 mm OPMU0-2
3.5 mm OPMU0-3
4.5 mm OPMU0-4
18° angulated abutment (indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
18°
1.5 mm OPMU18-1 IN
2.5 mm OPMU18-2 IN
3.5 mm OPMU18-3 IN
30° angulated abutment (indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
30°
0.75 mm OPMU30-0 IN
1.5 mm OPMU30-1 IN
2.5 mm OPMU30-2 IN
3.5 mm OPMU30-3 IN
18° angulated abutment (non-indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
18°
1.5 mm OPMU18-1
2.5 mm OPMU18-2
3.5 mm OPMU18-3
30° angulated abutment (non-indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
30°
0.75 mm OPMU30-0
1.5 mm OPMU30-1
2.5 mm OPMU30-2
3.5 mm OPMU30-3
NEW2015
CH = 2.5 mm
GH
Ø = 4.8 mm CH = 2.5 mm
Hmax*GH
Ø = 4.8 mm
ά
**CoCr = Cobalt Chromium.
IMPRESSION TAKING USING Ø 4.8 mm MULTI-UNIT ABUTMENTSPICK-UP technique: open tray orPOP-IN technique: closed tray
Multi-Unit pick-up transfer copingSupplied with two yellow pick-up screws (one short, one long)
MUT100 (x1)MUT100-4 (x4)
Multi-Unit pop-in transfer copingMUT200 (x1)
MUT200-4 (x4)
Multi-Unit abutment analogSupplied with one MU M1.4 blue screw
MUA100 (x1)MUA100-4 (x4)
Instrument Cat. No. Graphics
PROSTHETIC COMPONENTSFOR USE WITH Ø 4.8 mm MULTI-UNIT ABUTMENTS
Multi-Unit protective cap (titanium)
Supplied QMUCAP (x1)
MUCAP-4 (x4)
Multi-Unit titanium temporary copingSupplied with one titanium MU M1.4 screw
MUC100
Multi-Unit PEEK temporary copingSupplied with one titanium MU M1.4 screw
MUC200
Defi nitive Multi-Unit castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUC300
Defi nitive Multi-Unit CoCr** cast-on copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUC400
15N.cm
15N.cm
15N.cm
15N.cm
Manuel
NEW2015
NEW2015
NEW2015
NARROW MULTI-UNIT AUXILIARY COMPONENTS (
HC = 1.5 mm
HG
Ø = 4.0 mmGingival height
(GH)Cat. No. Graphics
0.75 mm OPMUN0-0
1.5 mm OPMUN0-1
2.5 mm OPMUN0-2
3.5 mm OPMUN0-3
4.5 mm OPMUN0-4*NEW2015
NEW2015
15N.cm
15
1-0
3-S
AO
15
1-0
4-S
AO
1 SAA: Scan-Adapter for implant-supported single-unit restorations2 SAO: Scan-Adapter for multiple-unit restorations using conical abutments3 Compatible with Simeda® approved scanners
*Hmax of 18° angled abutments = GH+1.5 mm. Hmax of 30° angled abutments = GH + 2.4 mm.
25N.cm
Black Tite® M1.6fi nal screw OPMU160
SUPPLIEDWITH
GE M U L T I P L E - U N I T S C R E W - R E T A I N E D R E S T O R A T I O N S
GE Ø 4.8 mm MULTI-UNIT RANGEØ 4.8 mm MULTI-UNIT ABUTMENTS
25N.cm
Component Cat. No. Graphics
PROSTHETIC COMPONENTSFOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit protective cap (titanium)Supplied Q MUNCAP
Narrow Multi-Unit temporary coping (titanium)Supplied with one titanium MU M1.4 screw
MUNC100
Narrow Multi-Unit PEEK temporary coping Supplied with one titanium MU M1.4 screw
MUNC200
Narrow Multi-Unit defi nitive castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUNC300
Narrow Multi-Unit CoCr** defi nitive castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUNC400
15N.cm
15N.cm
15N.cm
Manuel
w Used with Axiom® REG/PX implants for multiple-unit or full arch screw-retained restorations.
w Straight AND angulated abutments sharing the same auxiliary components.
w Supplied Q with a pre-assembled holder .
w Auxiliary components have a “yellow“ code.
GE Ø 4.0 mm MULTI-UNIT RANGEØ 4.0 mm NARROW MULTI-UNIT ABUTMENTSw Used with Axiom® REG and Axiom® PX implants for multiple-unit screw-retained restorations in patients with a small
inter-implant distance.w Straight narrow abutments use dedicated auxiliary components.w Supplied Q with a pre-assembled holder .w Auxiliary components have a “green“ code, or are marked «N» for narrow.
25N.cm
Instrument Cat. No. Graphics
TIGHTENING INSTRUMENTS FOR Ø 4.8 mm & 4.0 mm STRAIGHT MULTI-UNIT ABUTMENTS
Multi-Unit mandrel for 4.8 mm and 4.0 mmstraight abutments (short and long)
MUM100 MUM100L
Multi-Unit wrench for 4.8 mm and 4.0 mmstraight abutments
MUW100
SURGICAL INSTRUMENT
Angulated drill guide IN GFA
Ø 4.8 AND Ø 4.0 mmPREHENSILE TOOL
Short prehensile tool for Multi-Unit abutment MUWS
MULTI-UNIT PROSTHETIC & SURGICAL INSTRUMENTS
25N.cm
25N.cm
IMPRESSION TAKING COMPONENTS FOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit Pick-up transfer copingSupplied with two green pick-up screws (one short, one long)
MUNT100 (x1)MUNT100-4 (x4)
Narrow Multi-Unit Pop-in transfer coping MUNT200 (x1)MUNT200-4 (x4)
Narrow Multi-Unit Abutment analogSupplied with one MU M1.4 blue screw
MUNA100 (x1)MUNA100-4 (x4)
Composants Référence Visuels
MULTI-UNIT SCREWS FOR Ø 4.8 mm & 4.0 mm MULTI-UNIT ABUTMENTS
MU Black Tite® M1.6 fi nal screwMU M1.6 screw, Blue (x1)MU M1.6 screw, Blue (x4)
OPMU160OPMU161
OPMU161-4
MU Black Tite® M1.4 fi nal screwMU M1.4 screw, Blue
MU140MU141
Multi-Unit Laboratory screw, ShortMulti-Unit Laboratory screw, Long
MUT101MUT102
MULTI-UNIT ADDITIONAL COMPONENTS (all laboratory screws have a “blue“ code)
MULTI-UNIT PROTECTION ANALOGS, Ø 4.8 mm & 4.0 mm
Multi-Unit Protection analog, 4.8 mm(stainless steel)
MUA200 (x1)MUA200-4 (x4)
Multi-Unt Protection analog, 4.0 mm(stainless steel) MUNA200
MULTI-UNIT PROSTHETIC COMPONENTS FOR CAD/CAM RESTORATIONS ON AXIOM® REG/PX
Component Cat. No. Graphics
WAX-UP ACCESSORIESFOR CAD/CAM RESTORATIONS USING Ø 4.8 mm& 4.0 mm MULTI-UNIT ABUTMENTS
Ø 4.8 mm Multi-Unit Wax-upSupplied with one MU M1.4 blue screw
MUWAXUP (x1)MUWAXUP4 (x4)
Ø 4.8 mm Multi-Unit Wax-up and Laboratory screw Supplied with one MU M1.4 blue screw and one long laboratory blue screw
MUWAXUP-S (x1)MUWAXUP-S4 (x4)
Ø 4.0 mm Multi-Unit Wax-upSupplied with one MU M1.4 blue screw
MUNWAXUP (x1)MUNWAXUP4 (x4)
Ø 4.0 mm Multi-Unit Wax-up and Laboratory screw Supplied with one MU M1.4 blue screw and one long laboratory blue screw
MUNWAXUP-S (x1)MUNWAXUP-S4 (x4)
SCAN-ADAPTERS & SCAN-ADAPTER KITS FOR LABORATORY SCANNERS3
Scan-Adapter for Ø 4.8 mm Multi-Unit abutmentSupplied with fi xation screw
151-03-SAO
Scan-Adapter for Ø 4.0 mm Multi-Unit abutmentSupplied with fi xation screw
151-04-SAO
SA TOOL for fi xation of Scan-Adapter ontomaster model
SA TOOL -01
Scan-Adapter Kit for Axiom® REG/PX platforms.Includes 4 SAA1 for Axiom® REG/PX implants, 6 SAO2 for Axiom® REG/PX Ø 4.8 mm Multi-Unit abutments, and dedicated SA Tool (inserter).
151-02-KIT
PACIFIC COMPONENTSFOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit PACIFIC bonding ring Supplied with one MU Black Tite® M1.4 fi nal screw
MUNPAC100
Narrow Multi-Unit PACIFIC analog - Supplied with one MU M1.4 screw and one long laboratory blue screw
MUNPAC110
Narrow Multi-Unit PACIFIC castable copingSupplied with one MU M1.4 laboratory blue screw
MUNPAC120
Narrow Multi-Unit PACIFIC KitIncludes MUNPAC100/110/120
KITMUNPAC -
simeda®
customized &
solutionssolutions
Ø 4.0 mm NARROW MULTI-UNIT AUXILIARY COMPONENTS (“green“ code or “N“)Ø 4.8 MM MULTI-UNIT AUXILIARY COMPONENTS (“yellow“ code)
Axiom® Ø 4.8 mm Multi-Unit Abutments Angulation (ά)Gingival height
(GH)Cat. No. Graphics
Straight abutment (non-indexed)Supplied with a pre-assembled holder
0°
0.75 mm OPMU0-0
1.5 mm OPMU0-1
2.5 mm OPMU0-2
3.5 mm OPMU0-3
4.5 mm OPMU0-4
18° angulated abutment (indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
18°
1.5 mm OPMU18-1 IN
2.5 mm OPMU18-2 IN
3.5 mm OPMU18-3 IN
30° angulated abutment (indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
30°
0.75 mm OPMU30-0 IN
1.5 mm OPMU30-1 IN
2.5 mm OPMU30-2 IN
3.5 mm OPMU30-3 IN
18° angulated abutment (non-indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
18°
1.5 mm OPMU18-1
2.5 mm OPMU18-2
3.5 mm OPMU18-3
30° angulated abutment (non-indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
30°
0.75 mm OPMU30-0
1.5 mm OPMU30-1
2.5 mm OPMU30-2
3.5 mm OPMU30-3
NEW2015
CH = 2.5 mm
GH
Ø = 4.8 mm CH = 2.5 mm
Hmax*GH
Ø = 4.8 mm
ά
**CoCr = Cobalt Chromium.
IMPRESSION TAKING USING Ø 4.8 mm MULTI-UNIT ABUTMENTSPICK-UP technique: open tray orPOP-IN technique: closed tray
Multi-Unit pick-up transfer copingSupplied with two yellow pick-up screws (one short, one long)
MUT100 (x1)MUT100-4 (x4)
Multi-Unit pop-in transfer copingMUT200 (x1)
MUT200-4 (x4)
Multi-Unit abutment analogSupplied with one MU M1.4 blue screw
MUA100 (x1)MUA100-4 (x4)
Instrument Cat. No. Graphics
PROSTHETIC COMPONENTSFOR USE WITH Ø 4.8 mm MULTI-UNIT ABUTMENTS
Multi-Unit protective cap (titanium)
Supplied QMUCAP (x1)
MUCAP-4 (x4)
Multi-Unit titanium temporary copingSupplied with one titanium MU M1.4 screw
MUC100
Multi-Unit PEEK temporary copingSupplied with one titanium MU M1.4 screw
MUC200
Defi nitive Multi-Unit castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUC300
Defi nitive Multi-Unit CoCr** cast-on copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUC400
15N.cm
15N.cm
15N.cm
15N.cm
Manuel
NEW2015
NEW2015
NEW2015
NARROW MULTI-UNIT AUXILIARY COMPONENTS (
HC = 1.5 mm
HG
Ø = 4.0 mmGingival height
(GH)Cat. No. Graphics
0.75 mm OPMUN0-0
1.5 mm OPMUN0-1
2.5 mm OPMUN0-2
3.5 mm OPMUN0-3
4.5 mm OPMUN0-4*NEW2015
NEW2015
15N.cm
15
1-0
3-S
AO
15
1-0
4-S
AO
1 SAA: Scan-Adapter for implant-supported single-unit restorations2 SAO: Scan-Adapter for multiple-unit restorations using conical abutments3 Compatible with Simeda® approved scanners
*Hmax of 18° angled abutments = GH+1.5 mm. Hmax of 30° angled abutments = GH + 2.4 mm.
25N.cm
Black Tite® M1.6fi nal screw OPMU160
SUPPLIEDWITH
GE M U L T I P L E - U N I T S C R E W - R E T A I N E D R E S T O R A T I O N S
H I G H L Y P E R F O R M I N G S O L U T I O N S
MULTI-UNIT AbutmentsGE
Pho
to c
redi
t: A
ntho
gyr
- A
ll ri
ghts
res
erve
d. N
on c
ontr
actu
al p
hoto
s.C1
58_G
B -
201
5-04
ERGONOMIC RANGECOMPREHENSIVE RANGE
A RANGE OF 24 ABUTMENTS!
w 5 Gingival heights: 0.75, 1.5, 2.5, 3.5 and 4.5 mm.
w The 20° morse taper on the platform allowsgreater correction of axial malalignment.
HIGH-PERFORMANCE RANGEINTEGRITY OF AXIOM® ANGULATED MULTI-UNIT ABUTMENTS:Thanks to a unique design, integrity of these screw-retained abutments can be maintained with no trade-off to the wall thickness in critical zones:
The coronal part of the abutment is not truncated in the area that receives the MU M1.4 screw.
The connection system is not truncated at the base of the abutment which accommodates the M1.6 screw.
1
2
Gingival Height (mm) 0.75 1.5 2.5 3.5 4.5
Number of scribe lines
on coronal part0 1 2 3 4
Ø 4.8 mm Multi-Unit Abutments
18°
Angulation
w Angulated abutments (18° and 30°) in both indexed and non-indexed versions.
20° 20° 20°
30°18° or
COMMON PLATFORM
Ø = 4.8 mm
NARROW PLATFORM
Ø = 4.0 mmCOMMON OR NARROW PLATFORMSw Axiom® REG/PX angulated AND straight abutments have
a common Ø 4.8 mm platform and a 2.5 mmcoronal height (CH).Indicated for most multiple-unit screw-retained restorations. Reduced inventory of auxiliary components.
w Axiom® REG/PX straight abutments havea narrow Ø 4.0 mm platform and a reduced 1.5 mmcoronal height (CH).Indicated for multiple-unit screw-retained restorationsin patients with a small inter-implant distance.
EASY HANDLINGw Each abutment comes with its attached holder for easyEach abutment comes with its attached holder for easyEach abutment comes with its attached holder
transfer to the patient’s mouth and safer placement.w Can be used with the angulated drill guide.
QUICK IDENTIFICATIONw Each abutment is laser marked with angulation
(18° or 30°) and gingival height (CH).
EASY MANIPULATIONw Straight abutments have a tapered end which greatly
facilitates insertion.Angulated non indexed abutments feature a repositioning fl at.
w The taper angle on the coronal platform facilitatesplacement of auxiliary components.
ANGULATED DRILL GUIDEfor dental restorations using a limited number of implants
w 30° scribe lines on the drill guide;w 2 mm diameter support tip;w Drill guide height corresponds to tooth height: 10 mm;w Semi-fl exible stainless steel adapts for variances in
anatomy;w Pre-assembled holder assists in achieving parallel
alignment of Multi-Unit abutments.
Anthogyr SAS2 237, Avenue André Lasquin74700 Sallanches - FrancePhone: +33 (0)4 50 58 02 37 Fax: +33 (0)4 50 93 78 60 www.anthogyr.com
FOR ALL PLURAL RESTORATIONSw Partial or complete screw-retained bridges using Multi-Unit straight AND angulated abutments with
a COMMON platform.w Multiple-unit screw-retained restorations using Multi-Unit straight abutments with a NARROW
platform in patients with a small inter-implant distance.
Abutments are supplied Q for immediate loading.Q for immediate loading.Q
Ht 0.75 Ht 1.5 Ht 2.5 Ht 3.5 Ht 4.5
Multiple-UnitScrew-Retained Restorations
GE M U L T I P L E - U N I T S C R E W - R E T A I N E D R E S T O R A T I O N S
GE Ø 4.8 mm MULTI-UNIT RANGEØ 4.8 mm MULTI-UNIT ABUTMENTS
25N.cm
Component Cat. No. Graphics
PROSTHETIC COMPONENTSFOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit protective cap (titanium)Supplied Q MUNCAP
Narrow Multi-Unit temporary coping (titanium)Supplied with one titanium MU M1.4 screw
MUNC100
Narrow Multi-Unit PEEK temporary coping Supplied with one titanium MU M1.4 screw
MUNC200
Narrow Multi-Unit defi nitive castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUNC300
Narrow Multi-Unit CoCr** defi nitive castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUNC400
15N.cm
15N.cm
15N.cm
Manuel
w Used with Axiom® REG/PX implants for multiple-unit or full arch screw-retained restorations.
w Straight AND angulated abutments sharing the same auxiliary components.
w Supplied Q with a pre-assembled holder .
w Auxiliary components have a “yellow“ code.
GE Ø 4.0 mm MULTI-UNIT RANGEØ 4.0 mm NARROW MULTI-UNIT ABUTMENTSw Used with Axiom® REG and Axiom® PX implants for multiple-unit screw-retained restorations in patients with a small
inter-implant distance.w Straight narrow abutments use dedicated auxiliary components.w Supplied Q with a pre-assembled holder .w Auxiliary components have a “green“ code, or are marked «N» for narrow.
25N.cm
Instrument Cat. No. Graphics
TIGHTENING INSTRUMENTS FOR Ø 4.8 mm & 4.0 mm STRAIGHT MULTI-UNIT ABUTMENTS
Multi-Unit mandrel for 4.8 mm and 4.0 mmstraight abutments (short and long)
MUM100 MUM100L
Multi-Unit wrench for 4.8 mm and 4.0 mmstraight abutments
MUW100
SURGICAL INSTRUMENT
Angulated drill guide IN GFA
Ø 4.8 AND Ø 4.0 mmPREHENSILE TOOL
Short prehensile tool for Multi-Unit abutment MUWS
MULTI-UNIT PROSTHETIC & SURGICAL INSTRUMENTS
25N.cm
25N.cm
IMPRESSION TAKING COMPONENTS FOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit Pick-up transfer copingSupplied with two green pick-up screws (one short, one long)
MUNT100 (x1)MUNT100-4 (x4)
Narrow Multi-Unit Pop-in transfer coping MUNT200 (x1)MUNT200-4 (x4)
Narrow Multi-Unit Abutment analogSupplied with one MU M1.4 blue screw
MUNA100 (x1)MUNA100-4 (x4)
Composants Référence Visuels
MULTI-UNIT SCREWS FOR Ø 4.8 mm & 4.0 mm MULTI-UNIT ABUTMENTS
MU Black Tite® M1.6 fi nal screwMU M1.6 screw, Blue (x1)MU M1.6 screw, Blue (x4)
OPMU160OPMU161
OPMU161-4
MU Black Tite® M1.4 fi nal screwMU M1.4 screw, Blue
MU140MU141
Multi-Unit Laboratory screw, ShortMulti-Unit Laboratory screw, Long
MUT101MUT102
MULTI-UNIT ADDITIONAL COMPONENTS (all laboratory screws have a “blue“ code)
MULTI-UNIT PROTECTION ANALOGS, Ø 4.8 mm & 4.0 mm
Multi-Unit Protection analog, 4.8 mm(stainless steel)
MUA200 (x1)MUA200-4 (x4)
Multi-Unt Protection analog, 4.0 mm(stainless steel) MUNA200
MULTI-UNIT PROSTHETIC COMPONENTS FOR CAD/CAM RESTORATIONS ON AXIOM® REG/PX
Component Cat. No. Graphics
WAX-UP ACCESSORIESFOR CAD/CAM RESTORATIONS USING Ø 4.8 mm& 4.0 mm MULTI-UNIT ABUTMENTS
Ø 4.8 mm Multi-Unit Wax-upSupplied with one MU M1.4 blue screw
MUWAXUP (x1)MUWAXUP4 (x4)
Ø 4.8 mm Multi-Unit Wax-up and Laboratory screw Supplied with one MU M1.4 blue screw and one long laboratory blue screw
MUWAXUP-S (x1)MUWAXUP-S4 (x4)
Ø 4.0 mm Multi-Unit Wax-upSupplied with one MU M1.4 blue screw
MUNWAXUP (x1)MUNWAXUP4 (x4)
Ø 4.0 mm Multi-Unit Wax-up and Laboratory screw Supplied with one MU M1.4 blue screw and one long laboratory blue screw
MUNWAXUP-S (x1)MUNWAXUP-S4 (x4)
SCAN-ADAPTERS & SCAN-ADAPTER KITS FOR LABORATORY SCANNERS3
Scan-Adapter for Ø 4.8 mm Multi-Unit abutmentSupplied with fi xation screw
151-03-SAO
Scan-Adapter for Ø 4.0 mm Multi-Unit abutmentSupplied with fi xation screw
151-04-SAO
SA TOOL for fi xation of Scan-Adapter ontomaster model
SA TOOL -01
Scan-Adapter Kit for Axiom® REG/PX platforms.Includes 4 SAA1 for Axiom® REG/PX implants, 6 SAO2 for Axiom® REG/PX Ø 4.8 mm Multi-Unit abutments, and dedicated SA Tool (inserter).
151-02-KIT
PACIFIC COMPONENTSFOR USE WITH Ø 4.0 mm MULTI-UNIT NARROW ABUTMENTS
Narrow Multi-Unit PACIFIC bonding ring Supplied with one MU Black Tite® M1.4 fi nal screw
MUNPAC100
Narrow Multi-Unit PACIFIC analog - Supplied with one MU M1.4 screw and one long laboratory blue screw
MUNPAC110
Narrow Multi-Unit PACIFIC castable copingSupplied with one MU M1.4 laboratory blue screw
MUNPAC120
Narrow Multi-Unit PACIFIC KitIncludes MUNPAC100/110/120
KITMUNPAC -
simeda®
customized &
solutionssolutions
Ø 4.0 mm NARROW MULTI-UNIT AUXILIARY COMPONENTS (“green“ code or “N“)Ø 4.8 MM MULTI-UNIT AUXILIARY COMPONENTS (“yellow“ code)
Axiom® Ø 4.8 mm Multi-Unit Abutments Angulation (ά)Gingival height
(GH)Cat. No. Graphics
Straight abutment (non-indexed)Supplied with a pre-assembled holder
0°
0.75 mm OPMU0-0
1.5 mm OPMU0-1
2.5 mm OPMU0-2
3.5 mm OPMU0-3
4.5 mm OPMU0-4
18° angulated abutment (indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
18°
1.5 mm OPMU18-1 IN
2.5 mm OPMU18-2 IN
3.5 mm OPMU18-3 IN
30° angulated abutment (indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
30°
0.75 mm OPMU30-0 IN
1.5 mm OPMU30-1 IN
2.5 mm OPMU30-2 IN
3.5 mm OPMU30-3 IN
18° angulated abutment (non-indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
18°
1.5 mm OPMU18-1
2.5 mm OPMU18-2
3.5 mm OPMU18-3
30° angulated abutment (non-indexed)Supplied with a pre-assembled holder and one MU Black Tite® M1.6 fi nal screw
30°
0.75 mm OPMU30-0
1.5 mm OPMU30-1
2.5 mm OPMU30-2
3.5 mm OPMU30-3
NEW2015
CH = 2.5 mm
GH
Ø = 4.8 mm CH = 2.5 mm
Hmax*GH
Ø = 4.8 mm
ά
**CoCr = Cobalt Chromium.
IMPRESSION TAKING USING Ø 4.8 mm MULTI-UNIT ABUTMENTSPICK-UP technique: open tray orPOP-IN technique: closed tray
Multi-Unit pick-up transfer copingSupplied with two yellow pick-up screws (one short, one long)
MUT100 (x1)MUT100-4 (x4)
Multi-Unit pop-in transfer copingMUT200 (x1)
MUT200-4 (x4)
Multi-Unit abutment analogSupplied with one MU M1.4 blue screw
MUA100 (x1)MUA100-4 (x4)
Instrument Cat. No. Graphics
PROSTHETIC COMPONENTSFOR USE WITH Ø 4.8 mm MULTI-UNIT ABUTMENTS
Multi-Unit protective cap (titanium)
Supplied QMUCAP (x1)
MUCAP-4 (x4)
Multi-Unit titanium temporary copingSupplied with one titanium MU M1.4 screw
MUC100
Multi-Unit PEEK temporary copingSupplied with one titanium MU M1.4 screw
MUC200
Defi nitive Multi-Unit castable copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUC300
Defi nitive Multi-Unit CoCr** cast-on copingSupplied with one MU Black Tite® M1.4 fi nal screw
MUC400
15N.cm
15N.cm
15N.cm
15N.cm
Manuel
NEW2015
NEW2015
NEW2015
NARROW MULTI-UNIT AUXILIARY COMPONENTS (
HC = 1.5 mm
HG
Ø = 4.0 mmGingival height
(GH)Cat. No. Graphics
0.75 mm OPMUN0-0
1.5 mm OPMUN0-1
2.5 mm OPMUN0-2
3.5 mm OPMUN0-3
4.5 mm OPMUN0-4*NEW2015
NEW2015
15N.cm
15
1-0
3-S
AO
15
1-0
4-S
AO
1 SAA: Scan-Adapter for implant-supported single-unit restorations2 SAO: Scan-Adapter for multiple-unit restorations using conical abutments3 Compatible with Simeda® approved scanners
*Hmax of 18° angled abutments = GH+1.5 mm. Hmax of 30° angled abutments = GH + 2.4 mm.
25N.cm
Black Tite® M1.6fi nal screw OPMU160
SUPPLIEDWITH