general information...addendum no. 1 page - 5 august 20, 2018 sjcsd bid #2018-24 item no. 10.:...
TRANSCRIPT
Addendum No. 1 Page - 1 August 20, 2018 SJCSD Bid #2018-24
August 20, 2018
ADDENDUM NO. 1, to Drawings and Specifications dated July 30, 2018 for the Mill Creek K-8 Conversion
project for the St. Johns County School District, St. Augustine, FL., as prepared by SchenkelShultz, 200 E. Robinson Street, Suite 300, Orlando, Florida.
Bid #2018-24
This ADDENDUM NO. 1 shall hereby be and become a part of the Contract Documents the same as if originally bound thereto. The following clarifications, amendments, additions, revisions, changes and modifications change the original Contract Documents only in the amount and to the extent hereinafter specified and set forth in this ADDENDUM NO. 1.
GENERAL INFORMATION ITEM NO. 1.: PHASING PLAN The proposed Phasing Plan that delineates the scope of work to be completed for Phase 1 and Phase 2 is attached with this addendum. The Phase 1 construction is included in the current site contractor scope of services and is NOT to be included within this bid. The Phase 2 construction will be required by the selected general contractor.
ITEM NO. 2.: ESTIMATED CONSTRUCTION BUDGET Estimated Construction budget is in the range of $10M. ITEM NO. 3.: THE GC IS RESPONSIBLE FOR THEIR ELECTRIC AND WATER UNTIL
SUBSTANTIAL COMPLETION The GC will be required to contact FPL for temporary service. There is an existing single phase OH transformer located near the project site on the northerly side near the construction road. The meter and any low voltage connections would be the responsibility of the GC. ITEM NO. 4.: CONSTRUCTION PERSONNEL As long as construction personnel are within the confines of the construction fence barrier, badging will not be required. If any work is to be performed outside of the construction area, then that person(s) must be badged and cleared by the SJCSD. ITEM NO. 5.: SODDING THE AREA OUTSIDE THE CONSTRUCTION FENCE Sodding the area outside the construction fence and around the pond is part of phase 1. The general contractor will be responsible for fine grading and re-sodding inside the construction fence ITEM NO. 6.: LANDSCAPING There will be no landscaping at this project ITEM NO. 7.: IRRIGATION There will be no irrigation system at this project
Addendum No. 1 Page - 2 August 20, 2018 SJCSD Bid #2018-24
CHANGES TO PROJECT MANUAL ITEM NO. 1.: SPECIFICATION TABLE OF CONTENTS
A. Delete Table of Contents in its entirety and replace with the Table of Contents attached to this addendum. Work included but not limited to:
B. Sections added, deleted or revised as described below.
STRUCTURAL ITEM NO. 2.: SPECIFICATION SECTION 04 22 00 – CONCRETE UNIT MASONRY
A. Deleted Cavity Insulation from 1.2.E.1. ARCHITECTURAL ITEM NO. 3.: SECTION C - OWNER-CONTRACTOR AGREEMENT
A. Add Section C - Owner-Contractor Agreement in its entirety, attached to this addendum. ITEM NO. 4.: GENERAL CONDITIONS OF THE CONTRACT FOR CONSTRUCTION
A. Add the General Conditions of the Contract for Construction in its entirety, attached to this addendum.
ITEM NO. 5.: SECTION SC - SUPPLEMENTARY CONDITIONS
A. Add Section SC - Supplementary Conditions in its entirety, attached to this addendum. ITEM NO. 6.: SECTION 06 41 16 - PLASTIC-LAMINATE-CLAD ARCHITECTURAL CABINETS
A. Delete section 06 41 16 - Plastic-Laminate-Clad Architectural Cabinets in its entirety and replace with section 06 41 16 - Plastic-Laminate-Clad Architectural Cabinets, attached to this addendum. Work included but not limited to:
B. 1.2, A, 2; revise. C. 1.5, B, 1; delete. D. 1.5, C; delete. E. 1.5, C; add. F. 1.5, D, add. G. 2.1, A, 1; delete. H. 2.3; delete. I. 2.3; add. J. 3.3; delete.
ITEM NO. 7.: SECTION 08 71 00 - DOOR HARDWARE
A. Add Section 08 71 00 - Door Hardware in its entirety, attached to this addendum. ITEM NO. 8.: SECTION 09 65 40 - VINYL PLANK FLOORING
A. Revise section 09 65 40 - Vinyl Plank Flooring, in accordance with the following: B. 2.1, A, 4; add Tandus Centiva as an Acceptable Manufacturer. C. 2.1, A, 4, b; revise Wearlayer thickness to be .020” - 20 mils..
ITEM NO. 9.: SECTION 09 67 00 - EPOXY FLOOR COATING
A. Revise section 09 67 00 - Epoxy Floor Coating, in accordance with the following: B. 2.3, A, 1, e; add Tennant Company as an acceptable Manufacturer.
ITEM NO. 10.: SECTION 09 68 13 - CARPET TILE
A. Revise section 09 68 13 - Carpet Tile, in accordance with the following: B. 2.2, A, 3; add Tandus Centiva as an acceptable Manufacturer.
Addendum No. 1 Page - 3 August 20, 2018 SJCSD Bid #2018-24
ITEM NO. 11.: SECTION 10 51 00 - STANDARD LOCKERS A. Delete section 10 51 00 - Standard Lockers in its entirety and replace with section 10 51 00 -
Standard Lockers, attached to this addendum. Work included but not limited to: B. 1.11, A, 3; revise. C. 2.2, A, 3; add. D. 2.2, A, 4; add. E. 2.3, B; revise. F. 3.2, B; delete. G. 3.2, B; add.
ITEM NO. 12.: SECTION 10 51 13 - P.E. LOCKERS
A. Delete section 10 51 13 - P.E. Lockers in its entirety and replace with section 10 51 13 - P.E. Lockers, attached to this addendum. Work included but not limited to:
B. 1.11, A, 3; revise. C. 2.2, A; revise. D. 2.2, A, 3; add. E. 2.3, B; revise. F. 3.2, B; delete. G. 3.2, B; add.
ITEM NO. 13.: SECTION 12 48 13 - WALK-OFF ROLLED CARPET
A. Delete section 12 48 13 - Walk-off Rolled Carpet in its entirety and replace with section 12 48 13 - Walk-off Rolled Carpet, attached to this addendum. Work included but not limited to:
B. 2.4, Add. MECHANICAL ITEM NO. 14.: SPECIFICATION SECTION 23 05 14 – VARIABLE FREQUENCY MOTOR
CONTROLLERS A. Added “ABB” to the approved manufacturers list.
ITEM NO. 15.: SPECIFICATION SECTION 23 09 00 – INSTRUMENTATION AND CONTROL FOR
HVAC A. Delete Section 23 09 00 – Instrumentation and Control For HVAC in its entirety and replace with
section 23 09 00 – Instrumentation and Control For HVAC, attached to this addendum.
ITEM NO. 16.: SPECIFICATION SECTION 23 36 00 – AIR TERMINAL UNITS
A. Added “Enviro-Tec (ETI)” to the approved manufacturers list.
ITEM NO. 17.: SPECIFICATION SECTION 23 64 26 – SCROLL WATER CHILLERS
A. Renamed this section to “Scroll Water Chillers” from “Rotary-Screw Water Chillers”. B. Added “Daikin Applied” to the approved manufacturers list.
Addendum No. 1 Page - 4 August 20, 2018 SJCSD Bid #2018-24
CHANGES TO DRAWINGS CIVIL ITEM NO. 1.: DRAWING SHEET NO. C5 SITE PLAN
A. Delete drawing C5 in its entirety and replace with drawing C5 attached to this addendum. Work included but not limited to:
B. Updated the delineation and labeling for the recreation trail C. Added a note stating “all disturbed areas are to be permanently stabilized with Bahia sod”
ITEM NO. 2.: DRAWING SHEET NO. C10 CONSTRUCTION DETAILS
A. Delete drawing C10 in its entirety and replace with drawing C10 attached to this addendum. Work included but not limited to:
B. Added section detail for the asphalt recreation trail STRUCTURAL
ITEM NO. 3.: DRAWING SHEET NO. S101 CLASSROOM BLDG – FOUNDATION PLAN
A. Delete drawing S101 in its entirety and replace with drawing S101 attached to this addendum. Work included but not limited to:
B. Added north arrow. C. Added dimensions.
ITEM NO. 4.: DRAWING SHEET NO. S102 CLASSROOM BLDG – 2nd FLOOR FRAMING PLAN
A. Delete drawing S102 in its entirety and replace with drawing S102 attached to this addendum. Work included but not limited to:
B. Added north arrow. C. Added dimensions. D. Added bearing elevations
ITEM NO. 5.: DRAWING SHEET NO. S103 CLASSROOM BLDG – ROOF FRAMING PLAN
A. Work included: Added north arrow. ITEM NO. 6.: DRAWING SHEET NO. S104 GYM & CEP BLDG – FOUNDATION PLAN
A. Delete drawing S104 in its entirety and replace with drawing S104 attached to this addendum. Work included but not limited to:
B. Added north arrows. C. Revised top of slab elevations.
ITEM NO. 7.: DRAWING SHEET NO. S105 GYM BLDG – ROOF FRAMING PLAN
A. Work included: Added north arrow. ITEM NO. 8.: DRAWING SHEET NO. S301 FLOOR FRAMING SECTIONS AND DETAILS
A. Delete drawing S301 in its entirety and replace with drawing S301 attached to this addendum. Work included but not limited to:
B. Revised sections 6, 14, and 15. ARCHITECTURAL ITEM NO. 9.: DRAWING SHEET NO. A100 ARCHITECTURAL SITE PLAN
A. Parking areas depicted adjacent to the parking loop near International Golf Parkway are not included in the scope of this project.
B. The proposed new baseball field is a grass only field with a new backstop.
Addendum No. 1 Page - 5 August 20, 2018 SJCSD Bid #2018-24
ITEM NO. 10.: DRAWING SHEET NO. A100.1 CANOPY PLAN AND DETAIL A. Delete drawing A100.1 in its entirety and replace with drawing A100.1 attached to this addendum.
Work included but not limited to: B. Added dimensions and notes to Detail 1 - Overall Canopy Plan
ITEM NO. 11.: DRAWING SHEET NO. A101 CLASSROOM BLDG – 1ST FLOOR PLAN
A. The symbol designation of “A” inside a circle was changed to ”AP” inside a circle indicating rooms with Acoustic Partitions.
B. The symbol designation of “A” inside a diamond was changed to ”AR” inside a diamond indicating rooms with Abuse Resistant Gyp. Bd.
ITEM NO. 12.: DRAWING SHEET NO. A102 CLASSROOM BLDG – 2ND FLOOR PLAN
A. The symbol designation of “A” inside a circle was changed to ”AP” inside a circle indicating rooms with Acoustic Partitions.
B. The symbol designation of “A” inside a diamond was changed to ”AR” inside a diamond indicating rooms with Abuse Resistant Gyp. Bd.
ITEM NO. 13.: DRAWING SHEET NO. A103 GYM BLDG – FLOOR PLAN
A. The symbol designation of “A” inside a circle was changed to ”AP” inside a circle indicating rooms with Acoustic Partitions.
B. The symbol designation of “A” inside a diamond was changed to ”AR” inside a diamond indicating rooms with Abuse Resistant Gyp. Bd.
C. Revised the size for the condensing unit concrete pad outside Band room 708 to 6’-0”x6’-0” D. Revised the note for the condensing unit fence to read “Min. 6'-0" High Fencing with Gate around
the Equipment. Refer to detail 6/A902” ITEM NO. 14.: DRAWING SHEET NO. A301 CLASSROOM BLDG – 1ST FLOOR EQUIPMENT PLAN
A. Item “CC25 Walk Off Mats” was relocated to the Finish Plans B. Revised the equipment schedule, refer to SKA-1 attached with this addendum
ITEM NO. 15.: DRAWING SHEET NO. A302 CLASSROOM BLDG – 2ND FLOOR EQUIPMENT PLAN
A. Item “CC25 Walk Off Mats” was relocated to the Finish Plans B. Revised the equipment schedule, refer to SKA-1 attached with this addendum
ITEM NO. 16.: DRAWING SHEET NO. A303 GYM BLDG – EQUIPMENT PLAN
A. Item “CC25 Walk Off Mats” was relocated to the Finish Plans B. Revised the equipment schedule, refer to SKA-1 attached with this addendum
ITEM NO. 17.: DRAWING SHEET NO. A311 CLASSROOM BLDG – 1ST FLOOR FINISH PLAN
A. Located the fixed Walk Off Mats in this drawing instead of the equipment plans B. The floor finish at rooms 601, 601A, 606, 606A, 607 and 610 was revised to polished concrete
floor finish. C. The indication for LVT-1 and LVT-2 was revised in the finish schedule, refer to SKA-2 attached
with this addendum D. The polished concrete finish was added to the finish schedule, refer to SKA-2 attached with this
addendum
ITEM NO. 18.: DRAWING SHEET NO. A312 CLASSROOM BLDG – 2ND FLOOR FINISH PLAN A. Located the fixed Walk Off Mats in this drawing instead of the equipment plans B. The floor finish at rooms 621, 621A, 626, 626A and 630 was revised to polished concrete floor
finish. C. The indication for LVT-1 and LVT-2 was revised in the finish schedule, refer to SKA-2 attached
with this addendum D. The polished concrete finish was added to the finish schedule, refer to SKA-2 attached with this
addendum
Addendum No. 1 Page - 6 August 20, 2018 SJCSD Bid #2018-24
ITEM NO. 19.: DRAWING SHEET NO. A313 GYM BLDG – FINISH PLAN A. Located the fixed Walk Off Mats in this drawing instead of the equipment plans B. The indication for LVT-1 and LVT-2 was revised in the finish schedule, refer to SKA-2 attached
with this addendum C. The polished concrete finish was added to the finish schedule, refer to SKA-2 attached with this
addendum ITEM NO. 20.: DRAWING SHEET NO. A711 WALL SECTIONS
A. Detail 1 - Classroom Bldg. Wall Section 1 - Revised the top of the concrete beam (the bottom of the hollow core) to 112’-9 ½”
ITEM NO. 21.: DRAWING SHEET NO. A801 INTERIOR ELEVATIONS
A. Detail 12 – Typ. Demonstration Desk. Revised the note above this detail to read ”Plastic Laminate Cabinets, Counters and Backsplash, Typical Countertops and Backsplash at Science and Prep Rooms Shall be Chemical Resistant Plastic Laminate”
B. Detail 13 – Typ. Box Base Cabinet Section. Revised counter top note to read ”Plastic Laminate Countertop & Backsplash - See Interiors”
ITEM NO. 22.: DRAWING SHEET NO. A802 INTERIOR ELEVATIONS A. Detail 2 - Band Class - North West Elevation. Revised backsplash note to read
“High Plastic Laminate Backsplash” ITEM NO. 23.: DRAWING SHEET NO. A903 DETAILS
A. Added detail 7 - Backstop Detail. Refer to SKA-3 B. Added detail 8 - Backstop Section. Refer to SKA-4
PLUMBING
ITEM NO. 24.: DRAWING SHEET NO. P113 – GYM BLDG – PLUMBING PLAN - PRESSURE
A. Delete drawing P113 in its entirety and replace with drawing P113 attached to this addendum. Work included but not limited to:
B. Added cold water make-up line to CEP. MECHANICAL ITEM NO. 25.: DRAWING SHEET NO. M101 – CLASSROOM BLDG – 1ST FLOOR – HVAC PLAN
A. Revised note for outside air louver to clarify louver sizing, refer to SKM-1 attached with this addendum.
ITEM NO. 26.: DRAWING SHEET NO. M102 – CLASSROOM BLDG – 2ND FLOOR – HVAC PLAN
A. Revised note for outside air louver to clarify louver sizing, refer to SKM-2 attached with this addendum.
ITEM NO. 27.: DRAWING SHEET NO. M702 – HVAC CONTROLS
A. Delete drawing M702 in its entirety and replace with drawing M702 attached to this addendum. Work included but not limited to:
B. Added Water Heater Interface Diagram C. Revised BTU Meter Interface Diagram D. Deleted Typical VFD Interface Diagram (now located on M705)
ITEM NO. 28.: DRAWING SHEET NO. M703 – HVAC CONTROLS
A. Revised make-up water and air separator blow down to go to grade, refer to SKM-3 attached with this addendum.
ITEM NO. 29.: DRAWING SHEET NO. M705 – HVAC CONTROLS
A. Delete drawing M705 in its entirety and replace with drawing M705 attached to this addendum. Work included but not limited to:
Addendum No. 1 Page - 7 August 20, 2018 SJCSD Bid #2018-24
B. Added revised Typical VFD Interface Diagram C. Added Domestic Water Meter Interface Diagram D. Added Fire Alarm Meter Interface Diagram E. Added Exterior Lighting Controls Integration
ELECTRICAL
ITEM NO. 30.: DRAWING SHEET NO. E201 CLASSROOM BLDG – 1ST FLOOR POWER PLAN
A. Delete drawing E201 in its entirety and replace with drawing E201 attached to this addendum. Work included but not limited to:
B. Revised receptacles in Intermediate/Middle Science Classroom 601, 606, and 610 to GFCI receptacles.
ITEM NO. 31.: DRAWING SHEET NO. E202 CLASSROOM BLDG – 2ND FLOOR POWER PLAN
A. Delete drawing E202 in its entirety and replace with drawing E202 attached to this addendum. Work included but not limited to:
B. Revised receptacles in Intermediate/Middle Science Classroom 621, 626, and 630 to GFCI receptacles.
ITEM NO. 32.: DRAWING SHEET NO. E501 PANEL SCHEDULES
A. Delete drawing E501 in its entirety and replace with drawing E501 attached to this addendum. Work included but not limited to:
B. Revised panel schedules to indicate room name and number. C. Added note 1 to panel LP1.
ITEM NO. 33.: DRAWING SHEET NO. E502 PANEL SCHEDULES
A. Delete drawing E502 in its entirety and replace with drawing E502 attached to this addendum. Work included but not limited to:
B. Revised panel schedules to indicate room name and number. C. Added note 1 to panel LPG.
ITEM NO. 34.: DRAWING SHEET NO. E601 POWER RISER DIAGRAM
A. Revised riser to indicate transformer grounding electrode to be bonded to building steel, cold water pipe, refer to SKE-3, SKE-4, and SKE-5 attached with this addendum.
B. Revised riser to include reference callout, refer to SKE-3 attached with this addendum. ITEM NO. 35.: DRAWING SHEET NO. E602 FIRE ALARM AND GROUNDING DIAGRAM
A. Revised riser to indicate transformer grounding electrode to be bonded to building steel, cold water pipe, refer to SKE-6, and SKE-7 attached with this addendum.
ITEM NO. 36.: DRAWING SHEET NO. E704 ELECTRICAL DETAILS
A. Added detail 3, Metal Conduit Bonding, refer to SKE-1 attached with this addendum. B. Revised detail 1 to include reference callout, refer to SKE-2 attached with this addendum.
Addendum No. 1 Page - 8 August 20, 2018 SJCSD Bid #2018-24
ATTACHMENTS: GENERAL INFORMATION: PHASING PLAN SPECIFICATION SECTIONS: SPECIFICATION TABLE OF CONTENTS SECTION C - OWNER-CONTRACTOR AGREEMENT GENERAL CONDITIONS OF THE CONTRACT FOR CONSTRUCTION SECTION SC - SUPPLEMENTARY CONDITIONS SECTION 06 41 16 - PLASTIC-LAMINATE-CLAD ARCHITECTURAL CABINETS SECTION 08 71 00 - DOOR HARDWARE SECTION 10 51 00 - STANDARD LOCKERS SECTION 10 51 13 - P.E. LOCKERS SECTION 12 24 13 - WALK-OFF ROLLED CARPET SECTION 23 09 00 – INSTRUMENTATION AND CONTROL FOR HVAC DRAWINGS SHEETS: C5 SITE PLAN C10 CONSTRUCTION DETAILS S101 CLASSROOMS BLDG - FOUNDATION PLAN S102 CLASSROOMS BLDG - 2ND FLOOR FRAMING PLAN S104 GYM & CEP BLDG - FOUNDATION PLAN S301 FLOOR AND ROOF FRAMING SECTIONS AND DETAILS A100.1 CANOPY PLAN AND DETAIL P113 GYM BLDG – PLUMBING PLAN - PRESSURE M702 HVAC CONTROLS M705 HVAC CONTROLS E201 CLASSROOM BLDG – 1ST FLOOR POWER PLAN E202 CLASSROOM BLDG – 2ND FLOOR POWER PLAN E501 PANEL SCHEDULES E502 PANEL SCHEDULES SKETCHES: SKA-1 SKA-2 SKA-3 SKA-4 SKM-1 SKM-2 SKM-3 SKE-1 SKE-2 SKE-3 SKE-4 SKE-5 SKE-6 SKE-7
End of Addendum No. 1
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F F
F
F
F F
F
F F
F
F
F F
F
F
F F
F
F
F F
F
F F
F
F
F F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
FF
F
F
F
F
F
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XXXX
XXXXX
XX
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
XX
X
XX
XX
XX
XX
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X X
X
X X
X X X X
X X
X X X
X X X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
XX
X
XX
XX
X
XX
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
W
W
W
W
W
W
W
W
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X
X X
X
X
X
X
X
X
X
X
X
X X
X X
X
X
XX
X
X
XX
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
XXXXXXXXXXXXXXX
F
F
F
F
F
FF
F
F
F
F
F
W
W
W
W
W
WW
W
W
W
W
W
W
W
W
W
W
WW
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
WW
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
F
F
F
F
FF
F
F
F
F
F
F
F
F
F
F
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
XX
X
X
X
XX
X
X
X
XX
X
X
X
XX
X
X
X
XX
X
X
X
XX
X
X
X
XX
X
X
X
XX
X
X
X
XX
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X X
X
X X
X X
X
X X
X X
X
X X
X X
X X
X
X X
X X
X
X X
X X
X
X X
X X
X
X X
X X
X
X X
X X
X
X X
X X
X
X X
X X
X
X X
X X
X
X X
X X
X
X X
X X
X
X X
X X
X
X X
X X
X X
X
X X X
X
X
X
X X
X
X
X
X X
X
X
X
X
X X
X
X
X
X X
X
X
X
X
X X
X
X
X
X X
X
X
X
X
X X
X
X
X
X
X X
X
X
X
X X
X
X
X
X
X X
X
X
X
X X
X
X
X
X
X X
X
X
X
X X
X
X
X
X
X X
X
X
X X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
FF
F
F
F
F
F
F
FF
F
FF
F
F
FF
F
F
FF
F
F
FF
F
FF
F
F
FF
F
F
FF
F
F
FF
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
FF
F
F F
W
W
W
W
W
W
WW
F
F
F
F
F
F
F F
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
F
FF
F
F
F
F
F
F
F
F
F
F
F
F
FF
F
F
F
F F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
FF
F
F
F
F
F
F
F
M
E
C
H
.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
T
O
W
E
R
C
O
O
L
I
N
G
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
D
U
M
P
S
T
E
R
S
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X X
X X
X X
X X
X X X
X X
X X
X X
X X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
BENCHMARK No. 2:
SET MAG NAIL & DISK "LB
6824"
ELEVATION=26.53' N.G.V.D.
1929
INTERNATIO
NAL GOLF PARKWAY
INTERNATIO
NAL GOLF PARKWAY
BENCHMARK No. 1:
SET MAG NAIL & DISK "LB
6824"
ELEVATION=27.25' N.G.V.D.
1929
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
F
.
F
.
E
.
=
2
8
.
4
1
*
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm fm
fm
fm
fm fm
fm
fm
fm
fm fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
fm
26.90
27.70
27.30
27.75
28.00
28.30
27.75
28.00
27.25
27.63
28.00
28.30
27.70
28.30
27.70
27.70
27.70
27.70
27.10
27.25
26.75
27.00
26.3
26.9
26.3
25.4
26.0
25.4
24.5
25.4
24.5
26.0
26.0
26.0
22.0
25.8
22.3
20.0
23.6
26.0
25.8
22.9
19.8
17.6
17.8
20.7
23.0
25.9
25.9
22.9
19.9
17.7
17.8
20.0
23.2
25.8
25.9
22.9
20.7
17.9
19.7
26.0
23.3
26.0
17.7
19.8
23.0
25.8
17.6
19.8
19.8
22.4
25.8
23.0
25.8
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
XX
X
X
XX
X
X
XX
X
XX
X
X
XX
X
X
XX
X
XX
X
X
XX
X
X
XX
X
XX
X
X
XX
X
XX
X
X
XX
X
X
XX
X
XX
X
X
XX
X
X
XX
X
XX
X
X
XX
X
X
XX
X
XX
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
XX
X
XX
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
oe
EXISTING
BUILDING
EXISTING
BUILDING
EXISTING
BUILDING
EXISTING
BUILDING
EXISTING
BUILDING
EXISTING
PORTABLE UNITS
EXISTING UPLAND
BUFFER
EXISTING SWALE
MODIFIED SWMF
EXISTING SWALE
EXISTING FIRE
DEPARTMENT ACCESS
ROAD AND TURN AROUND
MULTI-PURPOSE
FIELD
BASEBALL
FIELD
PROPOSED
GYM BUILDING
AREA: 22,506 SF
EXISTING
SWMF
PROPOSED
CLASSROOM BUILDING
AREA: 19,042 SF
CHILLER AND
TRANSFORMER
CONSTRUCTION
TRAILER
12
17
18
TIE PERIMETER FENCING
INTO EXISTING
6' RECREATION
TRACK
6' RECREATION
TRACK
HATCH LEGENDPROPOSED SIDEWALK
PROPOSED PAVEMENT
WETLAND
UPLAND BUFFER
N
0
GRAPHIC SCALE120 16080
1"=80'
SHEET No.:
RE
VIS
IO
NS
DE
SC
RIP
TIO
N
MA
TT
HE
WS
DE
SIG
N G
RO
UP,
IN
C.
P.O
. BO
X 3
126,
7 W
AL
DO
ST
RE
ET
ST
. AU
GU
ST
INE
, FL
OR
IDA
320
84P
HO
NE
: 90
4.82
6.13
34F
AX
: 90
4.82
6.45
47IN
FO
@M
AT
TH
EW
SD
ES
IGN
.NE
T
S:\P
RO
JE
CT
S\1
80
00
\1
80
29
- M
IL
L C
RE
EK
K
-8
C
ON
VE
RS
IO
N\D
RA
WIN
GS
\C
ON
ST
RU
CT
IO
N D
OC
UM
EN
TS
\1
80
29
- C
ON
ST
RU
CT
IO
N D
OC
UM
EN
TS
P
HS
2
\1
80
29
- S
IT
E P
LA
N - (P
HA
SIN
G P
LA
N).D
WG
_M
AS
TE
R S
IT
E P
LA
N, 7
/3
0/2
01
8 4
:3
8 P
M, R
usse
ll F
lin
t, M
AT
TH
EW
S D
ES
IG
N G
RO
UP
, IN
C.
DA
TE
NO
.
DA
TE
:
JO
B N
o.:
DS
GN
B
Y:
DW
G B
Y:
CH
K B
Y:
OF
RE
GIS
TE
RE
D E
NG
IN
EE
R
PR
EP
AR
ED
F
OR
CA
#26535 F
L.#
5
18
PH
AS
IN
G P
LA
N
MIL
L C
REE
K S
ITE
IMPR
OV
EMEN
TSST
. JO
HN
S C
OU
NTY
ST. J
OH
NS
CO
UN
TY S
CH
OO
L D
ISTR
ICT
RD
F
NR
H
AR
A
06
/1
4/2
01
8
18
02
9
ALE
X R
. A
CR
EE
, P
.E
.
73155
----
1
----
----
----
----
7/2
6/1
8
----
----
----
----
AR
CH
P
LA
N, R
EC
RE
AT
IO
N T
RA
CK
, &
U
TIL
M
OD
IF
IC
AT
IO
NS
----
----
----
----
LEGENDPARCEL BOUNDARY
ROADWAY CENTERLINE
SILT FENCE
CONSTRUCTION FENCE
XXX
PHASE 1 (SUMMER)
1.GRADING OF PARKING & ACCESS ROAD
2. INSTALLATION OF STORM DRAINAGE FACILITIES
3. INSTALLATION OF WATER MAIN
4. INSTALLATION OF SECURITY FENCING, GATES, AND SILT FENCING.
PHASE 2 (AFTER SUBSTANTIAL COMPLETION OF BUILDINGS
1. REFRESH GRADING OF PARKING LOT AS NEEDED.
2. ASPHALT PAVING OF PARKING LOT AND ACCESS ROAD.
2. INSTALLATION OF WHEEL STOPS
PHASE 1 (SUMMER)
1 EXCAVATION OF ADDITIONAL POND AREA
2. FINISH GRADING OF POND AND MAINTENANCE BERM.
3. MODIFY CONTROL STRUCTURE, AND INSTALL INLET AND PIPE IN NORTHEAST CORNER,
4. STUB OUT THE ROOF DRAIN CONNECTION PIPE FROM THE POND, EXTENDING EASTERLY 10 FEET BEYOND THE
MAINTENANCE BERM AND CAP FOR PHASE 2 CONNECTION.
4. EROSION CONTROL OF POND BANKS BY PLACING SOD ALONG BANKS AND MAINTENANCE BERM.
PHASE 2
1. INSTALLATION OF PERMANENT FENCING AND GATES AROUND POND &
ALONG THE NORTH PROPERTY LINE.
2. SODDING OUTSIDE SLOPES OF POND TO BUILDINGS.
3. CONNECT TO ROOF DRAIN STORM DRAIN PIPING AND EXTEND ROOF DRAIN PIPING AROUND BUILDINGS, ETC.
PHASE 1 (SUMMER)
1. CLEARING AND GRUBBING AREA .
2. FILL IN AREA PER GRADES
3. SOD FIELD
4. PERMANENT PERIMETER FENCING
PHASE 2
1. INSTALLATION OF 6' WIDE TRACK
2. LIGHT POLES
3. COMPLETION OF FIELD AND GRADING
AROUND BUILDINGS AND WITHIN PHASE 2
CONSTRUCTION AREA
PHASE 1 (SUMMER)
1. INSTALLATION OF FIRE MAIN AND F.D.C.
PHASE 1 (SUMMER)
1. INSTALLATION OF FIRE MAIN AND
PHASE 2
SEWER SERVICES WILL BE
INCLUDED ONLY IN PHASE 2
AREAS OUTSIDE CLOUDED AREAS
WILL BE PHASE 2, THIS INCLUDES
1. BUILDING CONSTRUCTION
2. FINAL UTILITY CONNECTIONS
3. REAR PARKING LOT GRADING AND PAVING
4. STORM DRAIN AND ROOF DRAIN CONNECTIONS
5. SIDEWALKS
6. ANYTHING NOT SPECIFICALLY MENTIONED FOR PHASE 1
PHASE 1 (SUMMER)
1. INSTALLATION OF STORM DRAIN PIPE AND STRUCTURES FROM POND
TO TIE INTO EXISTING INLET
PHASE 2
1. OUTER LOOP OF PARKING LOT
MILL CREEK K-8 CONVERSION
St. Johns County School District
#1820108 TABLE OF CONTENTS TOC - 1
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
VOLUME - 1
COVER SHEET
TITLE PAGE
TABLE OF CONTENTS - REVISED ADDENDUM-01
DIVISION 00 - PROCUREMENT AND CONTRACTING REQUIREMENTS
------------ ADVERTISEMENT FOR BIDS
SECTION A INFORMATION FOR BIDDERS
SECTION B FORM OF PROPOSAL
------------ BID BOND
------------ PUBLIC ENTITY CRIMES FORM
------------ JESSICA LUNSFORD ACT FORM
------------ CERTIFICATION REGARDING DEBARMENT FORM
------------ DRUG FREE WORKPLACE CERTIFICATION FORM
SECTION C OWNER-CONTRACTOR AGREEMENT - ADDED ADDENDUM-01
------------ GENERAL CONDITIONS OF THE CONTRACT FOR CONSTRUCTION - ADDED
ADDENDUM-01
SECTION SC SUPPLEMENTARY CONDITIONS - ADDED ADDENDUM-01
00 00 04 STATEMENT OF COMPLIANCE
00 05 00 NON-ASBESTOS STATEMENT
A312-2010 PERFORMANCE BOND SAMPLE
A312-2010 PAYMENT BOND SAMPLE
00 31 33 SOIL INVESTIGATION DATA
------------ GEO-TECHNICAL REPORT
00 43 20 FLORIDA TRENCH SAFETY ACT
MILL CREEK K-8 CONVERSION
St. Johns County School District
#1820108 TABLE OF CONTENTS TOC - 2
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
DIVISION 01 - GENERAL REQUIREMENTS
01 11 00 SUMMARY OF WORK
01 26 13 REQUESTS FOR INFORMATION (RFI) PROCEDURES
------------ RFI FORM
01 28 00 SCHEDULE OF VALUES
01 31 13 PROJECT COORDINATION
01 31 19 PROJECT MEETINGS
01 32 00 SCHEDULES AND REPORTS
01 33 00 SUBMITTAL PROCEDURES
01 34 00 OWNER PURCHASED MATERIALS/EQUIPMENT
01 35 00 PRECEDENCE AND CONFLICT PROCEDURES AND INTENT
01 42 19 REFERENCE STANDARDS AND DEFINITIONS
01 45 00 QUALITY CONTROL
01 45 10 TESTING LABORATORY SERVICE
01 50 00 TEMPORARY FACILITIES AND CONTROLS
01 50 13 PROJECT SIGN
01 55 50 MAINTENANCE OF TRAFFIC
01 56 00 TEMPORARY CONTROLS
01 57 10 NPDES PERMIT CONFORMANCE
------------ STATE OF FLORIDA DEPARTMENT OF ENVIRONMENTAL PROTECTION GENERIC
STORMWATER PERMIT
------------ NOTICE OF INTENT TO USE GENERIC PERMIT FOR STORMWATER DISCHARGE
------------ NOTICE OF TERMINATION OF GENERIC PERMIT COVERAGE
01 60 00 PRODUCT REQUIREMENTS
01 60 10 PRODUCT SUBSTITUTIONS
01 60 20 FLORIDA PRODUCT APPROVAL
01 70 00 CLOSEOUT PROCEDURES
01 71 23 FIELD ENGINEERING
01 73 29 CUTTING AND PATCHING
01 74 13 CONSTRUCTION CLEANING 01 74 15 PEST CONTROL (DURING CONSTRUCTION)
01 78 36 WARRANTIES
01 80 15 SUSTAINABLE DESIGN REQUIREMENTS (GREEN GLOBES)
01 91 13 GENERAL COMMISSIONING REQUIREMENTS
DIVISION 03 - CONCRETE
03 11 00 CONCRETE FORMING
03 20 00 CONCRETE REINFORCING
03 30 00 CAST-IN-PLACE CONCRETE
03 35 43 POLISHED CONCRETE FINISHING
03 41 13 PRECAST CONCRETE HOLLOW CORE PLANKS
03 45 00 ARCHITECTURAL PRECAST CONCRETE
03 47 13 TILT-UP CONCRETE
03 52 16 LIGHTWEIGHT INSULATING CELLULAR CONCRETE
MILL CREEK K-8 CONVERSION
St. Johns County School District
#1820108 TABLE OF CONTENTS TOC - 3
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
DIVISION 04 - MASONRY
04 05 13 MASONRY MORTARING
04 05 16 MASONRY GROUTING
04 05 23 MASONRY ACCESSORIES
04 22 00 CONCRETE UNIT MASONRY
04 40 14 MARBLE WINDOW SILLS
DIVISION 05 - METALS
05 12 00 STRUCTURAL STEEL FRAMING
05 21 00 STEEL JOIST FRAMING
05 31 00 STEEL DECKING
05 50 00 METAL FABRICATIONS
05 52 13 PIPE AND TUBE RAILINGS
05 70 10 DECORATIVE METAL GRILLES
DIVISION 06 - WOOD, PLASTICS, AND COMPOSITES
06 10 53 MISCELLANEOUS ROUGH CARPENTRY
06 16 00 SHEATHING
06 41 16 PLASTIC-LAMINATE-CLAD ARCHITECTURAL CASEWORK - REVISED
ADDENDUM-01
DIVISION 07 - THERMAL AND MOISTURE PROTECTION
07 17 00 BENTONITE WATERPROOFING
07 21 00 BUILDING INSULATION
07 24 11 EXTERIOR FINISH SYSTEM
07 26 10 UNDERSLAB VAPOR RETARDER
07 52 16 MODIFIED BITUMINOUS MEMBRANE ROOFING
07 62 00 FLASHING AND SHEET METAL
07 72 33 ROOF HATCHES
07 84 13 PENETRATION FIRESTOPPING
07 92 00 JOINT SEALANTS
DIVISION 08 - OPENINGS
08 11 13 HOLLOW METAL DOORS AND FRAMES
08 14 16 WOOD DOORS
08 31 13 ACCESS DOORS AND FRAMES
08 41 13 ALUMINUM ENTRANCES AND STOREFRONT
08 51 13 ALUMINUM WINDOWS
08 71 00 DOOR HARDWARE - ADDED ADDENDUM-01
08 80 00 GLAZING
MILL CREEK K-8 CONVERSION
St. Johns County School District
#1820108 TABLE OF CONTENTS TOC - 4
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
DIVISION 09 - FINISHES09 21 16 GYPSUM BOARD SHAFT-WALL ASSEMBLIES
09 22 16 NON-STRUCTURAL METAL FRAMING
09 26 13 VENEER PLASTER
09 29 00 GYPSUM BOARD
09 30 00 TILE
09 51 00 ACOUSTICAL CEILING
09 64 66 WOOD FLOORING
09 65 13 RESILIENT BASE AND ACCESSORIES
09 65 40 VINYL PLANK FLOORING - REVISED ADDENDUM-01
09 67 00 EPOXY FLOOR COATING - REVISED ADDENDUM-01
09 68 13 CARPET TILE - REVISED ADDENDUM-01
09 84 13 FIXED SOUND PANELS
09 91 00 PAINTING
DIVISION 10 - SPECIALTIES
10 11 00 VISUAL DISPLAY BOARDS
10 14 00 IDENTIFYING DEVICES
10 21 13 TOILET COMPARTMENTS
10 26 00 WALL PROTECTION
10 28 13 TOILET ACCESSORIES
10 44 00 FIRE PROTECTION SPECIALTIES
10 51 00 STANDARD LOCKERS - REVISED ADDENDUM-01
10 51 13 P.E. LOCKERS - REVISED ADDENDUM-01
10 73 26 ALUMINUM WALKWAY COVERINGS AND CANOPIES
DIVISION 11 - EQUIPMENT
11 30 00 RESIDENTIAL EQUIPMENT
11 53 00 SCIENCE EQUIPMENT
11 66 00 ATHLETIC EQUIPMENT
11 66 53 GYMNASIUM DIVIDERS
DIVISION 12 - FURNISHINGS
12 20 00 WINDOW TREATMENT
12 35 80 MUSIC CASEWORK
12 66 00 TELESCOPING BLEACHERS
12 48 13 WALK-OFF ROLLED CARPET - REVISED ADDENDUM-01
12 48 16 ENTRANCE FLOOR GRILLES
DIVISION 14 - CONVEYING EQUIPMENT
14 24 23 HOLELESS HYDRAULIC PASSENGER ELEVATORS
MILL CREEK K-8 CONVERSION
St. Johns County School District
#1820108 TABLE OF CONTENTS TOC - 5
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
VOLUME - 2
COVER SHEET
TITLE PAGE
TABLE OF CONTENTS
DIVISION 21 - FIRE SUPPRESSION SYSTEMS
21 05 00 COMMON WORK RESULTS FOR FIRE SUPPRESSION
21 12 00 FIRE-SUPPRESSION STANDPIPES
21 13 13 WET-PIPE SPRINKLER SYSTEMS
21 13 16 DRY-PIPE SPRINKLER SYSTEMS
DIVISION 22 - PLUMBING SYSTEMS
22 05 00 COMMON WORK RESULTS FOR PLUMBING
22 05 19 METERS AND GAGES FOR PLUMBING PIPING
22 05 23 GENERAL-DUTY VALVES FOR PLUMBING PIPING
22 05 29 HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT
22 05 53 IDENTIFICATION FOR PLUMBING PIPING AND EQUIPMENT
22 07 00 PLUMBING PIPING INSULATION
22 11 16 DOMESTIC WATER PIPING
22 11 19 DOMESTIC WATER PIPING SPECIALTIES
22 13 16 SANITARY WASTE AND VENT PIPING
22 13 19 SANITARY WASTE PIPING SPECIALTIES
22 13 23 SANITARY WASTE INTERCEPTORS
22 14 13 FACILITY STORM DRAINAGE PIPING
22 14 23 STORM DRAINAGE PIPING SPECIALTIES
22 14 29 SUMP PUMPS
22 33 00 ELECTRIC DOMESTIC WATER HEATERS
22 40 00 PLUMBING FIXTURES
MILL CREEK K-8 CONVERSION
St. Johns County School District
#1820108 TABLE OF CONTENTS TOC - 6
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
DIVISION 23 - HVAC SYSTEMS
23 00 10 BASIC MECHANICAL REQUIREMENTS
23 05 13 COMMON MOTOR REQUIREMENTS FOR HVAC EQUIPMENT
23 05 14 VARIABLE FREQUENCY MOTOR CONTROLLERS - REVISED ADDENDUM-01
23 05 16 EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING
23 05 17 SLEEVES AND SLEEVE SEALS FOR HVAC PIPING
23 05 18 ESCUTCHEONS FOR HVAC PIPING
23 05 19 METERS AND GAGES FOR HVAC PIPING
23 05 23 GENERAL-DUTY VALVES FOR HVAC PIPING
23 05 29 HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT
23 05 48.13 VIBRATION CONTROLS FOR HVAC
23 05 53 IDENTIFICATION FOR HVAC PIPING AND EQUIPMENT
23 05 93 TESTING, ADJUSTING, AND BALANCING FOR HVAC
23 07 13 DUCT INSULATION
23 07 16 HVAC EQUIPMENT INSULATION
23 07 19 HVAC PIPING INSULATION
23 08 00 COMMISSIONING OF HVAC SYSTEMS
23 09 00 INSTRUMENTATION AND CONTROL FOR HVAC - REVISED ADDENDUM-01
23 11 23 FACILITY NATURAL-GAS PIPING
23 21 13 HYDRONIC PIPING
23 21 16 HYDRONIC PIPING SPECIALTIES
23 21 23 HYDRONIC PUMPS
23 25 00 HVAC WATER TREATMENT
23 31 13 METAL DUCTS
23 33 00 AIR DUCT ACCESSORIES
23 34 23 HVAC POWER VENTILATORS
23 36 00 AIR TERMINAL UNITS - REVISED ADDENDUM-01
23 37 13 DIFFUSERS, REGISTERS, AND GRILLES
23 37 23 HVAC GRAVITY VENTILATORS
23 41 01 AIR PURIFICATION SYSTEM
23 64 26 ROTARY-SCREW WATER CHILLERS - REVISED ADDENDUM-01
23 73 13 MODULAR INDOOR CENTRAL-STATION AIR-HANDLING UNITS
MILL CREEK K-8 CONVERSION
St. Johns County School District
#1820108 TABLE OF CONTENTS TOC - 7
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
DIVISION 26 - ELECTRICAL
26 00 13 POWER SYSTEM STUDY
26 02 00 BASIC MATERIALS AND METHODS FOR ELECTRICAL SYSTEMS
26 05 00 TESTS AND PERFORMANCE VERIFICATION
26 05 19 WIRES AND CABLES
26 05 26 GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS
26 05 33 RACEWAYS AND BOXES FOR ELECTRICAL SYSTEMS
26 05 38 FLOOR BOXES FOR ELECTRICAL SYSTEMS
26 05 43 PRIMARY DUCTBANK SYSTEM
26 05 53 IDENTIFICATION FOR ELECTRICAL SYSTEMS
26 08 16 DEMONSTRATION OF COMPLETED ELECTRICAL SYSTEMS
26 22 13 DRY-TYPE TRANSFORMERS
26 24 16 PANELBOARDS
26 24 17 DISTRIBUTION PANELBOARDS
26 27 26 WIRING DEVICES
26 28 19 ENCLOSED DISCONNECT SWITCHES
26 41 13 LIGHTNING PROTECTION SYSTEM
26 43 00 SURGE PROTECTION DEVICES
26 51 13 LIGHTING
DIVISION 27 - COMMUNICATIONS
27 05 00 COMMON WORK RESULTS FOR COMMUNICATIONS
27 26 26 DATA COMMUNICATIONS INTEGRATION REQUIREMENTS
27 41 00 AUDIO-VIDEO SYSTEMS
27 41 16 INTEGRATED AUDIO-VIDEO SYSTEMS AND EQUIPMENT
27 41 33 LOCAL AREA SOUND SYSTEM - GYMNASIUM
27 51 16 INTERCOM SYSTEM
27 53 13 GPS WIRELESS CLOCK SYSTEMS
DIVISION 28 - ELECTRONIC SAFETY AND SECURITY
28 13 10 ACCESS CONTROL SYSTEM
28 16 00 INTRUSION DETECTION SYSTEM
28 20 00 CAMERA SURVEILLANCE SYSTEM
28 31 11 DIGITAL, ADDRESSABLE FIRE-ALARM SYSTEM
DIVISION 31 - EARTHWORK
31 31 16 TERMITE CONTROL
DIVISION 32 - EXTERIOR IMPROVEMENTS
32 31 13 CHAIN LINK FENCE
END OF TABLE OF CONTENTS
MILL CREEK K-8 CONVERSION
St. Johns County School District
#1820108 TABLE OF CONTENTS TOC - 8
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
THIS PAGE INTENTIONALLY LEFT BLANK
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 PLASTIC LAMINATE-CLAD ARCHITECTURAL CABINETS 06 41 16 - 1
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
SECTION 06 41 16 PLASTIC-LAMINATE-CLAD ARCHITECTURAL CABINETS
PART 1 - GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply to this Section.
1.2 SUMMARY
A. Section Includes:
1. Plastic-laminate-faced architectural cabinets. 2. Laboratory countertops Chemical Resistant Plastic Laminate.
1.3 ACTION SUBMITTALS
A. Product Data: For each type of product, including high-pressure decorative laminate and cabinet hardware and accessories.
B. Shop Drawings: Show location of each item, dimensioned plans and elevations, large-scale details, attachment devices, and other components.
1. Show locations and sizes of furring, blocking, and hanging strips, including concealed blocking and reinforcement specified in other Sections.
2. Show locations and sizes of cutouts and holes for electrical switches and outlets and other items installed in architectural plastic-laminate cabinets.
3. Apply AWI Quality Certification Program label to Shop Drawings.
C. Samples for Initial Selection:
1. Plastic laminates. 2. PVC edge material. 3. Thermoset decorative panels. 4. Countertops.
D. Samples for Verification: For each type of casework, exposed-hardware, and countertop-material finish.
1. Plastic laminates, 12 by 12 inches, for each type, color, pattern, and surface finish, with one sample applied to core material and specified edge material applied to one edge.
2. Thermoset decorative panels, 12 by 12 inches, for each color, pattern, and surface finish, with edge banding on one edge.
3. Corner pieces as follows:
a. Cabinet-front frame joints between stiles and rails, as well as exposed end pieces, 18 inches high by 18 inches wide by 6 inches deep.
b. Miter joints for standing trim.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 PLASTIC LAMINATE-CLAD ARCHITECTURAL CABINETS 06 41 16 - 2
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
4. Exposed cabinet hardware and accessories, one unit for each type and finish. 5. Countertop material, one unit for each type and finish.
1.4 INFORMATIONAL SUBMITTALS
A. Qualification Data: For manufacturer.
B. Product Test Reports: For countertop surface material, based on evaluation of comprehensive tests performed by a qualified testing agency, indicating compliance of laboratory countertop surface material with requirements specified for chemical and physical resistance.
C. Quality Standard Compliance Certificates: AWI Quality Certification Program.
1.5 QUALITY ASSURANCE
A. Defective workmanship or damaged components shall be corrected, repaired, or replaced as requested by the Architect, without further cost to the Owner.
B. Fabricator Qualifications: Shop that employs skilled workers who custom fabricate products similar to those required for this Project and whose products have a record of successful in-service performance.
1. Shop Certification: AWI's Quality Certification Program accredited participant.
C. Installer Qualifications: AWI's Quality Certification Program accredited participant.
C. Manufacturer Qualifications: Minimum 7 years experience in the manufacturer and installation of the type of cabinets specified.
D. Installer Qualifications: Minimum 5 years experience in the installation of the type of cabinets specified.
D.E. Coordinate delivery of templates and other similar items from other trades necessary for the construction of required casework units.
E.F. Coordinate submittals with construction schedule ensuring timely review to avoid delays from installation.
F.G. Casework shall be manufactured and install to meet the requirements of the Florida Building Code 6TH Edition (2017) and the Florida Fire Prevention Code 6TH Edition (2017).
1.6 PREINSTALLATION MEETINGS
A. Preinstallation Conference: Conduct conference at Project site.
1.7 DELIVERY, STORAGE, AND HANDLING
A. Do not deliver cabinets until painting and similar operations that could damage woodwork have been completed in installation areas. If cabinets must be stored in other than installation areas, store only in areas where environmental conditions comply with requirements specified in Field Conditions Article.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 PLASTIC LAMINATE-CLAD ARCHITECTURAL CABINETS 06 41 16 - 3
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
1.8 FIELD CONDITIONS
A. Environmental Limitations: Do not deliver or install cabinets until building is enclosed, wet work is complete, and HVAC system is operating and maintaining temperature and relative humidity at occupancy levels during the remainder of the construction period.
B. Field Measurements: Where cabinets are indicated to fit to other construction, verify dimensions of other construction by field measurements before fabrication, and indicate measurements on Shop Drawings. Coordinate fabrication schedule with construction progress to avoid delaying the Work.
1. Locate concealed framing, blocking, and reinforcements that support cabinets by field measurements before being enclosed, and indicate measurements on Shop Drawings.
C. Established Dimensions: Where cabinets are indicated to fit to other construction, establish dimensions for areas where cabinets are to fit. Provide allowance for trimming at site, and coordinate construction to ensure that actual dimensions correspond to established dimensions.
1.9 COORDINATION
A. Coordinate sizes and locations of framing, blocking, furring, reinforcements, and other related units of Work specified in other Sections to ensure that cabinets can be supported and installed as indicated.
PART 2 - PRODUCTS
2.1 PLASTIC-LAMINATE-FACED ARCHITECTURAL CABINETS
A. Quality Standard: Unless otherwise indicated, comply with the "Architectural Woodwork Standards" for grades of architectural plastic-laminate cabinets indicated for construction, finishes, installation, and other requirements.
1. Provide inspections of fabrication and installation together with labels and certificates from AWI certification program indicating that woodwork complies with requirements of grades specified.
B. Type of Construction: Frameless.
C. Cabinet, Door, and Drawer Front Interface Style: Full Overlay.
D. High-Pressure Decorative Laminate: NEMA LD 3, grades as indicated or if not indicated, as required by woodwork quality standard.
1. Colors, Patterns, and Finishes:
a. Basis of Design Product and Manufacturer; As Scheduled on the interior Finish Schedule, subject to compliance with requirements other Manufacturers offering products which may be incorporated into the work are but not limited to the following:
1) Formica Corporation. 2) Lamin-Art, Inc.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 PLASTIC LAMINATE-CLAD ARCHITECTURAL CABINETS 06 41 16 - 4
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
3) Wilsonart LLC.
E. Laminate Cladding for Exposed Surfaces:
1. Horizontal Surfaces: Grade HGS. 2. Vertical Surfaces: Grade VGS. 3. Edges: Grade HGS.
F. Materials for Semiexposed Surfaces:
1. Horizontal and vertical surfaces: Grade CLS.
G. Concealed Backs of Panels with Exposed Plastic-Laminate Surfaces: High-pressure decorative laminate, NEMA LD 3, Grade BKL.
H. Drawer Construction: Fabricate with exposed fronts fastened to subfront with mounting screws from interior of body.
1. Medium-Density Fiberboard: ANSI A208.2, made with binder containing no urea formaldehyde.
2. Drawer Bottoms: White Birch or White Maple plywood; not less than 1/4-inch thick.
2.2 CABINET CONSTRUCTION
A. Support bases for base cabinets shall be 1-inch x 4-inch minimum pressure treated material. Cabinet Base: 4-inch high, 3/4 inch PT plywood. Provide additional center support for cabinets over 24 inches wide.
B. Base, Wall, and Tall Cabinet Boxes
1. Sides, bottom, and top: Constructed of glued and spline doweled 3/4 inch formaldehyde-free plywood providing balanced construction, surfaced with cabinet liner CLS for semi-exposed and vertical grade laminate for exposed locations.
2. Wall cabinet bottoms and tops: Constructed of glued and spline doweled one inch thick formaldehyde-free plywood, providing balanced construction surfaced with vertical grade laminate for exposed locations and cabinet liner CLS for semi-exposed locations.
3. Back panel: Constructed of minimum 1/4 inch prefinished tempered hard board, surfaced with CLS for semi-exposed and vertical grade laminate for exposed locations, inset and glued into sides, bottom, and top.
4. Exposed backs: Constructed of 3/4 inch formaldehyde-free plywood, surfaced with vertical grade laminate of balanced construction for semi-exposed locations, glued and spline doweled, and mechanically attached if required.
5. Intermediate support rail: Minimum 3/4 inch formaldehyde-free plywood, surfaced with vertical grade laminate of balanced construction, glued and doweled into cabinet sides.
6. Hanger rails: Two located at top and bottom of cabinet back, 3 on tall cabinets, locate at top, bottom, and center of 3/4 inch formaldehyde-free plywood.
C. Fixed and Adjustable Shelves and Dividers
1. One inch (formaldehyde-free plywood) shelves 2. Exposed Locations: Vertical grade plastic laminate both sides. Color to match cabinet
exterior plastic laminate or as selected by Architect. 3. Semi-exposed locations: VGS or CLS
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 PLASTIC LAMINATE-CLAD ARCHITECTURAL CABINETS 06 41 16 - 5
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
4. Front and back leading edges shall be edged with flat 1mm thick high impact PVC edging to match shelf color.
5. Number of adjustable shelves provided, unless indicated otherwise on the Drawings or on the Schedule
a. Low and tall cabinets b. 1 up to 24 inches 4 up to 72 inches c. 2 up to 36 inches 5 up to 84 inches d. 3 up to 60 inches 6 up to 96 inches e. Wall hung cabinets f. 0 up to 24 inches 2 up to 36 inches g. 1 up to 30 inches 3 up to 40 inches
6. Adjustable dividers: 1/4 inch minimum thickness, prefinished tempered hardboard or plywood, smooth both faces, retained by molded plastic support clip.
7. Fixed dividers: Constructed of 3/4 inch plywood, surfaced with vertical grade laminate, providing balanced construction; glued and spline doweled. PVC edged to match laminate or adjacent PVC edging.
D. Cabinet Doors
1. 3/4 inch formaldehyde-free particleboard 2. High pressure plastic vertical grade laminate exterior and interior. 3. Doors 48 inches and less in length shall have 2 hinges per door; doors over 48 inches in
length shall have 3 hinges per door. 4. Corners: Square with radiused edges, 3mm PVC edging.
E. Drawers
1. Manufacturers standard construction of minimum components listed below; or high density fiber board; glued and doweled or dovetail jointed; surfaced with vertical grade laminate of balanced construction. Bottoms constructed of minimum 1/4-inch tempered hardboard, surfaced to match drawer sides, inset and glued to four sides.
2. Drawer Face
a. Constructed of minimum 3/4-inch plywood, surfaced with VGS, screw attached to the drawer box.
1) Corners: To match doors. 2) Edging: To match doors. 3) Plastic Laminate: To match doors.
3. File Drawers: File drawers shall be constructed in accordance with standard drawers specified above with the following: Include front-to-back and side-to-side hanger file capability with hanger channel for letter size files integral with file drawer sides and 3/16-inch by 1/2-inch removable steel channel to span side-to-side for legal size hanging files.
F. Counter tops:
1. High Pressure Plastic Laminate: GP-50 grade. 2. Plywood concealed members; solid formaldehyde-free plywood shall be 7 – Ply marine
grade boat plywood or Baltic birch marine grade boat plywood. 3. Plywood shall incorporate Type II water resistant glue. 4. Horizontal work surfaces to be 1-1/2 inch thick unless otherwise noted.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 PLASTIC LAMINATE-CLAD ARCHITECTURAL CABINETS 06 41 16 - 6
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
5. Cut openings in countertops for sinks or other items required. Cut to size from template furnished by supplier of sinks or use the designated sinks on job.
6. Edging: Radius, with 3mm PVC. 7. Provide balancing sheet on opposite face. 8. Laminate tops shall be continuous in practical lengths. When requiring splice joints, use
a combination of splines or dowels for alignment and Tite-Joint fasteners as required to make a uniform and gapless joint.
9. Backsplash and Endsplashes: Scribable, square set, color matching, and mechanically attached.
a. Backsplashes are required at locations where countertops abut walls where indicated on Drawings.
b. Edges of back and endsplashes shall be of square edge configuration.
2.3 LABORATORY COUNTERTOP MATERIALS
A. Epoxy: Factory-molded, modified epoxy-resin formulation with smooth, nonspecular finish.
1. Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to the following:
a. Durcon Incorporated. b. Prime Industries, Inc.
2. Physical Properties:
a. Flexural Strength: Not less than 10,000 psi. b. Modulus of Elasticity: Not less than 2,000,000 psi. c. Hardness (Rockwell M): Not less than 100. d. Water Absorption (24 Hours): Not more than 0.02 percent. e. Heat Distortion Point: Not less than 260 deg F.
3. Chemical Resistance: Epoxy-resin material has the following ratings when tested with indicated reagents according to NEMA LD 3, Test Procedure 3.4.5:
a. No Effect: Acetic acid (98 percent), acetone, ammonium hydroxide (28 percent), benzene, carbon tetrachloride, dimethyl formamide, ethyl acetate, ethyl alcohol, ethyl ether, methyl alcohol, nitric acid (70 percent), phenol, sulfuric acid (60 percent), and toluene.
b. Slight Effect: Chromic acid (60 percent) and sodium hydroxide (50 percent).
4. Color: As selected by Architect from epoxy manufacturer's full range.
2.3 Chemical-Resistant Plastic Laminate:
A. Basis of Design Product and Manufacturer; Chemtop, Formica Corporation.
B. Subject to compliance with requirements, other available manufacturers offering products that may be incorporated into the Work include, but are not limited to the following:
1. Nevamar; a Panolam Industries International, Inc. brand.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 PLASTIC LAMINATE-CLAD ARCHITECTURAL CABINETS 06 41 16 - 7
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
2. Wilsonart.
C. Color: As selected by Architect from chemical-resistant, plastic-laminate manufacturer's full range.
D. Sealants: Fully bed and seal splashes to tops and to other splashes with Dow Corning 786 Mildew Resistant Silicone Sealant, clear; or Architect approved equal.
2.4 CABINET HARDWARE AND ACCESSORIES
A. General: Provide cabinet hardware and accessory materials associated with architectural cabinets.
1. Hinges:
a. Steel, institutional 5 knuckle with interlaying leaves, 270-degree swing, hospital tipped with non-removable pins fastened with 4 screws each leaf into faces. No edge fastening allowed, equal to National lock No. 851, 2-3/4”.
b. Thickness .090 inch minimum c. Doors 48 inches and over shall have 3 hinges per leaf d. Finish: Powder coat baked-on enamel, color as selected by Architect.
2. Pulls:
a. 4-inch solid aluminum or stainless-steel wire pulls, fastened from back with two screws. For sliding doors, provide recessed stainless steel flush pulls. Provide two pulls for drawers more than 24 inches wide. Pull design shall comply with Americans with Disability Act (ADA).
3. Drawer Slides:
a. Manufacturer's standard, epoxy coated metal, ball bearing type, 75 pounds dynamic load, bottom mounted, captive profile, epoxy finished, nylon rollers, with positive in-stop and out-stop.
b. Provide outstop and outkeeper to maintain drawer in 80 percent open position. c. File drawers and paper storage drawers: Same as above except full extension
and load rating static position to be no less than 150 pounds.
4. Locks
a. Provide locks at clinic, ESE, first aid and gym lobby cabinet doors and drawers. b. Locks shall be of cylinder type cast with 5-disc tumbler mechanism. Each lock
shall be provided with milled brass key and keying as specified in keyed different and master keyed or keyed alike. Locks shall be provided as shown on equipment drawings or described in cabinet description.
c. Each area or room shall be keyed alike. d. Locks shall be master keyed using the casework manufacturer's keying system.
(This is independent to the building master keying system.) e. Provide automatic door bolt on double doors at leaf opposite lock core. f. Provide Locks for clinic, art and science rooms, do not provide locks for cabinetry
in classrooms.
5. Metal Adjustable Shelf Standards and Supports: BHMA A156.9, B04071; with shelf rests, B04081.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 PLASTIC LAMINATE-CLAD ARCHITECTURAL CABINETS 06 41 16 - 8
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
a. At Locations Indicated b. Finish to match other cabinet hardware.
6. Adjustable Shelf Supports: Metal, 2 pin, anti-lift, minimum 200 pounds capacity support clip. Support to accept either 3/4 inch or 1-inch thick shelf.
7. Catches: Magnetic type, adjusted for maximum 5-pound pull. Attach with screws and slotted for adjustment.
2.5 PLASTIC LAMINATE COUNTER TOPS
A. Square Edge Configurations: 1 inch to 1-1/8 inch thick monolithic particleboard with 1-1/4 inch edge face including top and bottom laminates.
B. Top and matching front edge to be high pressure plastic laminate factory bonded.
C. Provide balancing sheet on opposite face.
D. Provide countertops for base cabinets and counter sections.
E. Laminate tops and shall be continuous in practical lengths. When requiring splice joints, use a combination of splines or dowels for alignment and tite-joint fasteners as required to make a uniform and gapless joint.
1. Provide continuous top for counter type cabinets fixed in a line.
F. Provide 4 inch high scribable, square set, color matching, mechanically attached backsplash with endsplashes.
1. Backsplashes are required at locations where countertops abut walls where indicated on Drawings.
G. Edges of back and endsplashes shall be of square edge configuration.
H. Sealants: Fully bed and seal splashes to tops and to other splashes with clear Sanitary Silicone Sealant Refer to Section 07 92 00 Joint Sealants.
2.6 MISCELLANEOUS MATERIALS
A. Furring, Blocking, Shims, and Hanging Strips: Softwood or hardwood lumber, kiln dried to less than 15 percent moisture content.
B. Anchors: Select material, type, size, and finish required for each substrate for secure anchorage. Provide metal expansion sleeves or expansion bolts for post-installed anchors. Use nonferrous-metal or hot-dip galvanized anchors and inserts at inside face of exterior walls and at floors.
C. Adhesives: Do not use adhesives that contain urea formaldehyde.
2.7 FABRICATION
A. General: Fabricate cabinets and shelves to dimensions, profiles, and details indicated.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 PLASTIC LAMINATE-CLAD ARCHITECTURAL CABINETS 06 41 16 - 9
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
1. Complete fabrication, including assembly and hardware application, to maximum extent possible before shipment to Project site. Disassemble components only as necessary for shipment and installation. Where necessary for fitting at site, provide ample allowance for scribing, trimming, and fitting.
2. Shop-cut openings to maximum extent possible to receive hardware, appliances, electrical work, and similar items. Locate openings accurately and use templates or roughing-in diagrams to produce accurately sized and shaped openings. Sand edges of cutouts to remove splinters and burrs.
B. Veneer Core Substrate: As indicated.
C. Countertops: Provide plastic-laminate backer sheet, Grade BKL, on underside of countertop substrates.
D. Shelves: 3/4-inch plywood core with high pressure laminate all sides and edges. Maximum depth shall be 24 –inches. Maximum length shall be 36 inches. Finish all edges including top and bottom.
E. All visible surfaces of cabinetry not concealed shall be laminated.
PART 3 - EXECUTION
3.1 PREPARATION
A. Before installation, condition cabinets to average prevailing humidity conditions in installation areas.
B. Before installing cabinets, examine shop-fabricated work for completion and complete work as required.
3.2 INSTALLATION
A. Grade: Install cabinets to comply with same grade as item to be installed.
B. Assemble cabinets and complete fabrication at Project site to the extent that it was not completed in the shop.
C. Install cabinets level, plumb, true, and straight. Shim as required with concealed shims. Install level and plumb to a tolerance of 1/8 inch in 96 inches.
D. Scribe and cut cabinets to fit adjoining work, refinish cut surfaces, and repair damaged finish at cuts.
E. Anchor cabinets to anchors or blocking built in or directly attached to substrates. Secure with countersunk, concealed fasteners and blind nailing. Use fine finishing nails or finishing screws for exposed fastening, countersunk and filled flush with woodwork.
1. Use filler matching finish of items being installed.
F. Cabinets: Install without distortion so doors and drawers fit openings properly and are accurately aligned. Adjust hardware to center doors and drawers in openings and to provide unencumbered operation. Complete installation of hardware and accessory items as indicated.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 PLASTIC LAMINATE-CLAD ARCHITECTURAL CABINETS 06 41 16 - 10
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
1. Install cabinets with no more than 1/8 inch in 96-inch sag, bow, or other variation from a straight line.
3.3 INSTALLATION OF COUNTERTOPS
A. Comply with installation requirements in SEFA 2. Abut top and edge surfaces true in plane with flush hairline joints and with internal supports placed to prevent deflection. Locate joints where indicated on Shop Drawings.
B. Field Jointing: Where possible, make in same manner as shop-made joints, using dowels, splines, fasteners, adhesives, and sealants recommended by manufacturer. Shop prepare edges for field-made joints.
C. Fastening:
1. Secure epoxy countertops to cabinets with epoxy cement, applied at each corner and along perimeter edges at not more than 48 inches o.c.
2. Where necessary to penetrate countertops with fasteners, countersink heads approximately 1/8 inch and plug hole flush with material equal to countertop in chemical resistance, hardness, and appearance.
D. Provide holes and cutouts required for service fittings.
E. Provide scribe moldings for closures at junctures of countertop, curb, and splash with walls as recommended by manufacturer for materials involved. Match materials and finish to adjacent laboratory casework. Use chemical-resistant, permanently elastic sealing compound where recommended by manufacturer.
F. Dress joints smooth, remove surface scratches, and clean entire surface.
3.43.3 CLEANING AND PROTECTING
A. Clean finished surfaces, touch up as required, and remove or refinish damaged or soiled areas to match original factory finish, as approved by Architect.
B. Protect countertop surfaces during construction with 6-mil plastic or other suitable water-resistant covering. Tape to underside of countertop at a minimum of 48 inches o.c.
C. Repair damaged and defective cabinets, where possible, to eliminate functional and visual defects; where not possible to repair, replace woodwork. Adjust joinery for uniform appearance.
D. Clean, lubricate, and adjust hardware.
END OF SECTION 06 41 16
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 1 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
SECTION 08 71 00 DOOR HARDWARE
PART 1 - GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section.
1.2 SUMMARY
A. This Section includes commercial door hardware for the following:
1. Swinging doors. 2. Other doors to the extent indicated.
B. Door hardware includes, but is not necessarily limited to, the following:
1. Mechanical door hardware. 2. Electromechanical door hardware. 3. Automatic operators. 4. Cylinders specified for doors in other sections.
C. Codes and References: Comply with the version year adopted by the Authority Having Jurisdiction.
1. ANSI A117.1 - Accessible and Usable Buildings and Facilities. 2. ICC/IBC - International Building Code. 3. NFPA 70 - National Electrical Code. 4. NFPA 80 - Fire Doors and Windows. 5. NFPA 101 - Life Safety Code. 6. NFPA 105 - Installation of Smoke Door Assemblies. 7. UL/ULC and CSA C22.2 – Standards for Automatic Door Operators Used on Fire and
Smoke Barrier Doors and Systems of Doors. 8. State Building Codes, Local Amendments.
D. Standards: All hardware specified herein shall comply with the following industry standards:
1. ANSI/BHMA Certified Product Standards - A156 Series 2. UL10C – Positive Pressure Fire Tests of Door Assemblies
1.3 SUBMITTALS
A. Product Data: Manufacturer's product data sheets including installation details, material descriptions, dimensions of individual components and profiles, operational descriptions and finishes.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 2 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
B. Door Hardware Schedule: Prepared by or under the supervision of supplier, detailing fabrication and assembly of door hardware, as well as procedures and diagrams. Coordinate the final Door Hardware Schedule with doors, frames, and related work to ensure proper size, thickness, hand, function, and finish of door hardware.
1. Format: Comply with scheduling sequence and vertical format in DHI's "Sequence and Format for the Hardware Schedule."
2. Organization: Organize the Door Hardware Schedule into door hardware sets indicating complete designations of every item required for each door or opening. Organize door hardware sets in same order as in the Door Hardware Sets at the end of Part 3. Submittals that do not follow the same format and order as the Door Hardware Sets will be rejected and subject to resubmission.
3. Content: Include the following information:
a. Type, style, function, size, label, hand, and finish of each door hardware item.
b. Manufacturer of each item.
c. Fastenings and other pertinent information.
d. Location of door hardware set, cross-referenced to Drawings, both on floor plans and in door and frame schedule.
e. Explanation of abbreviations, symbols, and codes contained in schedule.
f. Mounting locations for door hardware.
g. Door and frame sizes and materials.
h. Warranty information for each product.
4. Submittal Sequence: Submit the final Door Hardware Schedule at earliest possible date, particularly where approval of the Door Hardware Schedule must precede fabrication of other work that is critical in the Project construction schedule. Include Product Data, Samples, Shop Drawings of other work affected by door hardware, and other information essential to the coordinated review of the Door Hardware Schedule.
C. Shop Drawings: Details of electrified access control hardware indicating the following:
1. Wiring Diagrams: Upon receipt of approved schedules, submit detailed system wiring diagrams for power, signaling, monitoring, communication, and control of the access control system electrified hardware. Differentiate between manufacturer-installed and field-installed wiring. Include the following:
a. Wiring instructions for each electronic component scheduled herein.
2. Electrical Coordination: Coordinate with related sections the voltages and wiring details required at electrically controlled and operated hardware openings.
D. Proof of Qualification: Provide copy of manufacturer(s) Factory Trained Installer documentation indicating proof of status as a qualified installer of Windstorm assemblies.
E. Keying Schedule: After a keying meeting with the owner has taken place prepare a separate keying schedule detailing final instructions. Submit the keying schedule in electronic format. Include keying system explanation, door numbers, key set symbols, hardware set numbers and special instructions. Owner must approve submitted keying schedule prior to the ordering of permanent cylinders/cores.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 3 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
F. Informational Submittals:
1. Hurricane Resistant Openings (State of Florida): Within the State of Florida, provide copy of current State of Florida Product Approval or Metro-Dade County Notice of Acceptance (NOA) as proof of compliance that doors, frames and hardware for exterior opening assemblies have been tested and approved for use at the wind load and design pressure level requirements specified for the Project.
a. Hurricane Resistant Components (State of Florida): Within the State of Florida, provide copy of independent, third party certified listing to ANSI A250.13.
2. Product Test Reports: Indicating compliance with cycle testing requirements, based on evaluation of comprehensive tests performed by manufacturer and witnessed by a qualified independent testing agency.
G. Operating and Maintenance Manuals: Provide manufacturers operating and maintenance manuals for each item comprising the complete door hardware installation in quantity as required in Division 01, Closeout Submittals.
1.4 QUALITY ASSURANCE
A. Manufacturers Qualifications: Engage qualified manufacturers with a minimum 5 years of documented experience in producing hardware and equipment similar to that indicated for this Project and that have a proven record of successful in-service performance.
B. Installer Qualifications: A minimum 3 years documented experience installing both standard and electrified door hardware similar in material, design, and extent to that indicated for this Project and whose work has resulted in construction with a record of successful in-service performance.
C. Door Hardware Supplier Qualifications: Experienced commercial door hardware distributors with a minimum 5 years documented experience supplying both mechanical and electromechanical hardware installations comparable in material, design, and extent to that indicated for this Project. Supplier recognized as a factory direct distributor by the manufacturers of the primary materials with a warehousing facility in Project's vicinity. Supplier to have on staff a certified Architectural Hardware Consultant (AHC) available during the course of the Work to consult with Contractor, Architect, and Owner concerning both standard and electromechanical door hardware and keying.
D. Automatic Operator Supplier Qualifications: Power operator products and accessories are required to be supplied and installed through current members of the manufacturer's "Power Operator Preferred Installer" program. Suppliers are to be factory trained, certified, and a direct purchaser of the specified power operators and be responsible for the installation and maintenance of the units and accessories indicated for the Project.
E. Source Limitations: Obtain each type and variety of door hardware specified in this section from a single source unless otherwise indicated.
1. Electrified modifications or enhancements made to a source manufacturer's product line by a secondary or third party source will not be accepted.
2. Provide electromechanical door hardware from the same manufacturer as mechanical door hardware, unless otherwise indicated.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 4 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
F. Hurricane Resistant Exterior Openings (State of Florida including the High Velocity Hurricane Zone (HVHZ)): Provide exterior door hardware as complete and tested assemblies, or component assemblies, including approved doors and frames specified under Section 081113 "Hollow Metal Doors and Frames", to meet the wind loads, design pressures, debris impact resistance, and glass and glazing requirements as detailed in the current State of Florida building code sections applicable to the Project.
1. Each unit to bear third party permanent label in accordance with the Florida Building Code requirements.
G. Each unit to bear third party permanent label demonstrating compliance with the referenced standards.
H. Keying Conference: Conduct conference to comply with requirements in Division 01 Section "Project Meetings." Keying conference to incorporate the following criteria into the final keying schedule document:
1. Function of building, purpose of each area and degree of security required. 2. Plans for existing and future key system expansion. 3. Requirements for key control storage and software. 4. Installation of permanent keys, cylinder cores and software. 5. Address and requirements for delivery of keys.
I. Pre-Submittal Conference: Conduct coordination conference in compliance with requirements in Division 01 Section "Project Meetings" with attendance by representatives of Supplier(s), Installer(s), and Contractor(s) to review proper methods and the procedures for receiving, handling, and installing door hardware.
1. Prior to installation of door hardware, conduct a project specific training meeting to instruct the installing contractors' personnel on the proper installation and adjustment of their respective products. Product training to be attended by installers of door hardware (including electromechanical hardware) for aluminum, hollow metal and wood doors. Training will include the use of installation manuals, hardware schedules, templates and physical product samples as required.
2. Inspect and discuss electrical roughing-in, power supply connections, and other preparatory work performed by other trades.
3. Review sequence of operation narratives for each unique access controlled opening. 4. Review and finalize construction schedule and verify availability of materials. 5. Review the required inspecting, testing, commissioning, and demonstration procedures
J. At completion of installation, provide written documentation that components were applied to manufacturer's instructions and recommendations and according to approved schedule.
1.5 DELIVERY, STORAGE, AND HANDLING
A. Inventory door hardware on receipt and provide secure lock-up and shelving for door hardware delivered to Project site. Do not store electronic access control hardware, software or accessories at Project site without prior authorization.
B. Tag each item or package separately with identification related to the final Door Hardware Schedule, and include basic installation instructions with each item or package.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 5 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
C. Deliver, as applicable, permanent keys, cylinders, cores, access control credentials, software and related accessories directly to Owner via registered mail or overnight package service. Instructions for delivery to the Owner shall be established at the "Keying Conference".
1.6 COORDINATION
A. Templates: Obtain and distribute to the parties involved templates for doors, frames, and other work specified to be factory prepared for installing standard and electrified hardware. Check Shop Drawings of other work to confirm that adequate provisions are made for locating and installing hardware to comply with indicated requirements.
B. Door Hardware and Electrical Connections: Coordinate the layout and installation of scheduled electrified door hardware and related access control equipment with required connections to source power junction boxes, low voltage power supplies, detection and monitoring hardware, and fire and detection alarm systems.
C. Door and Frame Preparation: Doors and corresponding frames are to be prepared, reinforced and pre-wired (if applicable) to receive the installation of the specified electrified, monitoring, signaling and access control system hardware without additional in-field modifications.
1.7 WARRANTY
A. General Warranty: Reference Division 01, General Requirements. Special warranties specified in this Article shall not deprive Owner of other rights Owner may have under other provisions of the Contract Documents and shall be in addition to, and run concurrent with, other warranties made by Contractor under requirements of the Contract Documents.
B. Warranty Period: Written warranty, executed by manufacturer(s), agreeing to repair or replace components of standard and electrified door hardware that fails in materials or workmanship within specified warranty period after final acceptance by the Owner. Failures include, but are not limited to, the following:
1. Structural failures including excessive deflection, cracking, or breakage. 2. Faulty operation of the hardware. 3. Deterioration of metals, metal finishes, and other materials beyond normal weathering. 4. Electrical component defects and failures within the systems operation.
C. Standard Warranty Period: One year from date of Substantial Completion, unless otherwise indicated.
D. Special Warranty Periods:
1. Ten years for mortise locks and latches. 2. Ten years for extra heavy duty cylindrical (bored) locks and latches. 3. Five years for exit hardware. 4. Twenty five years for manual surface door closer bodies. 5. Five years for motorized electric latch retraction exit devices. 6. Two years for electromechanical door hardware.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 6 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
1.8 MAINTENANCE SERVICE
A. Maintenance Tools and Instructions: Furnish a complete set of specialized tools and maintenance instructions as needed for Owner's continued adjustment, maintenance, and removal and replacement of door hardware.
PART 2 - PRODUCTS
2.1 SCHEDULED DOOR HARDWARE
A. General: Provide door hardware for each door to comply with requirements in Door Hardware Sets and each referenced section that products are to be supplied under.
B. Designations: Requirements for quantity, item, size, finish or color, grade, function, and other distinctive qualities of each type of door hardware are indicated in the Door Hardware Sets at the end of Part 3. Products are identified by using door hardware designations, as follows:
1. Named Manufacturer's Products: Product designation and manufacturer are listed for
each door hardware type required for the purpose of establishing requirements. Manufacturers' names are abbreviated in the Door Hardware Schedule.
C. Substitutions: Requests for substitution and product approval for inclusive mechanical and electromechanical door hardware in compliance with the specifications must be submitted in writing and in accordance with the procedures and time frames outlined in Division 01, Substitution Procedures. Approval of requests is at the discretion of the architect, owner, and their designated consultants.
2.2 HANGING DEVICES
A. Hinges: ANSI/BHMA A156.1 certified butt hinges with number of hinge knuckles and other options as specified in the Door Hardware Sets.
1. Quantity: Provide the following hinge quantity:
a. Two Hinges: For doors with heights up to 60 inches.
b. Three Hinges: For doors with heights 61 to 90 inches.
c. Four Hinges: For doors with heights 91 to 120 inches.
d. For doors with heights more than 120 inches, provide 4 hinges, plus 1 hinge for every 30 inches of door height greater than 120 inches.
2. Hinge Size: Provide the following, unless otherwise indicated, with hinge widths sized for door thickness and clearances required:
a. Widths up to 3’0”: 4-1/2” standard or heavy weight as specified.
b. Sizes from 3’1” to 4’0”: 5” standard or heavy weight as specified.
3. Hinge Weight and Base Material: Unless otherwise indicated, provide the following:
a. Exterior Doors: Heavy weight, non-ferrous, ball bearing or oil impregnated bearing hinges unless Hardware Sets indicate standard weight.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 7 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
b. Interior Doors: Standard weight, steel, ball bearing or oil impregnated bearing hinges unless Hardware Sets indicate heavy weight.
4. Hinge Options: Comply with the following:
a. Non-removable Pins: Provide set screw in hinge barrel that, when tightened into a groove in hinge pin, prevents removal of pin while door is closed; for the all out-swinging lockable doors.
5. Manufacturers:
a. Hager Companies (HA).
b. McKinney Products; ASSA ABLOY Architectural Door Accessories (MK).
c. Stanley Hardware (ST).
B. Pin and Barrel Continuous Hinges: ANSI/BHMA A156.26 Grade 1-600 certified pin and barrel continuous hinges with minimum 14 gauge Type 304 stainless steel hinge leaves, concealed teflon coated stainless pin, and twin self lubricated nylon bearings at each knuckle separation. Factory trim hinges to suit door height and prepare for electrical cut-outs.
1. Manufacturers:
a. Markar Products; ASSA ABLOY Architectural Door Accessories (MR).
b. McKinney Products; ASSA ABLOY Architectural Door Accessories (MK).
2.3 POWER TRANSFER DEVICES
A. Electrified Quick Connect Transfer Hinges: Provide electrified transfer hinges with Molex™ standardized plug connectors and sufficient number of concealed wires (up to 12) to accommodate the electrified functions specified in the Door Hardware Sets. Connectors plug directly to through-door wiring harnesses for connection to electric locking devices and power supplies. Wire nut connections are not acceptable.
1. Manufacturers:
a. Hager Companies (HA) - ETW-QC (# wires) Option.
b. McKinney Products; ASSA ABLOY Architectural Door Accessories (MK) - QC (# wires) Option.
c. Stanley Hardware (ST) – C Option.
B. Electrified Quick Connect Stainless Steel Continuous Transfer Hinges: Provide electrified transfer stainless steel continuous hinges with electrical transfer access prep accessible without de-mounting door from the frame. Furnish with Molex™ standardized plug connectors with sufficient number of concealed wires (up to 12) to accommodate the electrified functions specified in the Door Hardware Sets. Connectors plug directly to through-door wiring harnesses for connection to electric locking devices and power supplies. Wire nut connections are not acceptable.
1. Manufacturers:
a. Markar Products; ASSA ABLOY Architectural Door Accessories (MR) - MP-ETAP-EL (# wires) Option.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 8 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
b. McKinney Products; ASSA ABLOY Architectural Door Accessories (MK) - MCK-ETAP-EL (# wires) Option.
C. Concealed Quick Connect Electric Power Transfers: Provide concealed wiring pathway housing mortised into the door and frame for low voltage electrified door hardware. Furnish with Molex™ standardized plug connectors and sufficient number of concealed wires (up to 12) to accommodate the electrified functions specified in the Door Hardware Sets. Connectors plug directly to through-door wiring harnesses for connection to electric locking devices and power supplies. Wire nut connections are not acceptable.
1. Manufacturers:
a. Pemko Products; ASSA ABLOY Architectural Door Accessories (PE) – EL-CEPT Series.
b. Securitron (SU) - EL-CEPT Series.
c. Von Duprin (VD) - EPT-10 Series.
D. Electric Door Wire Harnesses: Provide electric/data transfer wiring harnesses with standardized plug connectors to accommodate up to twelve (12) wires. Connectors plug directly to through-door wiring harnesses for connection to electric locking devices and power supplies. Provide sufficient number and type of concealed wires to accommodate electric function of specified hardware. Provide a connector for through-door electronic locking devices and from hinge to junction box above the opening. Wire nut connections are not acceptable. Determine the length required for each electrified hardware component for the door type, size and construction, minimum of two per electrified opening.
1. Provide one each of the following tools as part of the base bid contract:
a. McKinney Products; ASSA ABLOY Architectural Door Accessories (MK) - Electrical Connecting Kit: QC-R001.
b. McKinney Products; ASSA ABLOY Architectural Door Accessories (MK) - Connector Hand Tool: QC-R003.
2. Manufacturers:
a. McKinney Products; ASSA ABLOY Architectural Door Accessories (MK) – QC-C Series.
2.4 DOOR OPERATING TRIM
A. Flush Bolts and Surface Bolts: ANSI/BHMA A156.3 and A156.16, Grade 1, certified.
1. Flush bolts to be furnished with top rod of sufficient length to allow bolt retraction device location approximately six feet from the floor.
2. Furnish dust proof strikes for bottom bolts. 3. Surface bolts to be minimum 8” in length and U.L. listed for labeled fire doors and U.L.
listed for windstorm components where applicable. 4. Provide related accessories (mounting brackets, strikes, coordinators, etc.) as required
for appropriate installation and operation.
5. Manufacturers:
a. Rockwood Products; ASSA ABLOY Architectural Door Accessories (RO).
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 9 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
b. Trimco (TC).
B. Coordinators: ANSI/BHMA A156.3 certified door coordinators consisting of active-leaf, hold-open lever and inactive-leaf release trigger. Model as indicated in hardware sets.
1. Manufacturers:
a. Rockwood Products; ASSA ABLOY Architectural Door Accessories (RO).
b. Trimco (TC).
C. Door Push Plates and Pulls: ANSI/BHMA A156.6 certified door pushes and pulls of type and design specified in the Hardware Sets. Coordinate and provide proper width and height as required where conflicting hardware dictates.
1. Push/Pull Plates: Minimum .050 inch thick, size as indicated in hardware sets, with beveled edges, secured with exposed screws unless otherwise indicated.
2. Fasteners: Provide manufacturer's designated fastener type as indicated in Hardware Sets.
3. Manufacturers:
a. Rockwood Products; ASSA ABLOY Architectural Door Accessories (RO).
b. Trimco (TC).
2.5 CYLINDERS AND KEYING
A. General: Cylinder manufacturer to have minimum (10) years experience designing secured master key systems and have on record a published security keying system policy.
B. Source Limitations: Obtain each type of keyed cylinder and keys from the same source manufacturer as locksets and exit devices, unless otherwise indicated.
1. Manufacturers:
a. Sargent Manufacturing (SA).
b. No Substitution.
C. Cylinders: Original manufacturer cylinders complying with the following:
1. Mortise Type: Threaded cylinders with rings and cams to suit hardware application. 2. Rim Type: Cylinders with back plate, flat-type vertical or horizontal tailpiece, and raised
trim ring. 3. Bored-Lock Type: Cylinders with tailpieces to suit locks. 4. Mortise and rim cylinder collars to be solid and recessed to allow the cylinder face to be
flush and be free spinning with matching finishes. 5. Keyway: Manufacturer’s Standard.Match Facility Standard.
D. Security Cylinders: ANSI/BHMA A156.5, Grade 1, patterned security cylinders and keys able to be used together under the same facility master or grandmaster key system. Cylinders are to be factory keyed.
1. Manufacturers:
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 10 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
a. Sargent Manufacturing (SA) - Signature Series.
b. No Substitution.
E. Keying System: Each type of lock and cylinders to be factory keyed.
1. Conduct specified "Keying Conference" to define and document keying system instructions and requirements.
2. Furnish factory cut, nickel-silver large bow permanently inscribed with a visual key control number as directed by Owner.
3. Existing System: Key locks to Owner's existing system.
F. Key Quantity: Provide the following minimum number of keys:
1. Change Keys per Cylinder: Two (2) 2. Master Keys (per Master Key Level/Group): Five (5). 3. Construction Keys (where required): Ten (10).
G. Construction Keying: Provide construction master keyed cylinders.
H. Key Registration List (Bitting List):
1. Provide keying transcript list to Owner's representative in the proper format for importing into key control software.
2. Provide transcript list in writing or electronic file as directed by the Owner.
I. Key Control Cabinet: Provide a key control system including envelopes, labels, and tags with self-locking key clips, receipt forms, 3-way visible card index, temporary markers, permanent markers, and standard metal cabinet. Key control cabinet shall have expansion capacity of 150% of the number of locks required for the project.
1. Manufacturers:
a. Lund Equipment (LU).
b. Telkee (TK).
2.6 MECHANICAL LOCKS AND LATCHING DEVICES
A. Mortise Locksets, Grade 1 (Heavy Duty): ANSI/BHMA A156.13, Series 1000, Operational Grade 1 certified. Locksets are to be manufactured with a corrosion resistant steel case and be field-reversible for handing without disassembly of the lock body.
1. Mortise locks to be certified Security Grade 1.
2. Extended cycle test: Locks to have been cycle tested in ordinance with ANSI/BHMA 156.13 requirements to 10 million cycles.
3. Manufacturers:
a. Corbin Russwin Hardware (RU) – ML2000 Series.
b. Sargent Manufacturing (SA) – 8200 Series.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 11 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
B. Tubular Locksets, Grade 1 (Extra-Heavy Duty): ANSI/BHMA A156.2 Series 4000, Grade 1 certified.
1. Locksets to withstand 3000 inch pounds of torque applied to the locked lever without gaining access.
2. Locksets to fit a standard 2 1/8” bore without the use of through-bolts.
3. Lever handles to be made of solid material with no plastic fillers.
4. Latchbolt head to be one-piece stainless steel construction encased within the lock body.
5. Extended cycle test: Locks to have been cycle tested in ordinance with ANSI/BHMA A156.2 requirements to 34 million cycles.
6. Furnish with standard 2 3/4” backset and 1/2" throw latchbolt (3/4" at rated paired openings).
7. Manufacturers:
a. Sargent Manufacturing (SA) – 11 Line.
2.7 AUXILIARY LOCKS
A. Mortise Deadlocks, Small Case: ANSI/BHMA A156.36, Grade 1, small case mortise type deadlocks constructed of heavy gauge wrought corrosion resistant steel. Steel or stainless steel bolts with a 1" throw and hardened steel roller pins. Deadlocks to be products of the same source manufacturer and keyway as other specified locksets.
1. Manufacturers:
a. Corbin Russwin Hardware (RU) - DL4100 Series.
b. Sargent Manufacturing (SA) - 4870 Series.
2.8 LOCK AND LATCH STRIKES
A. Strikes: Provide manufacturer's standard strike with strike box for each latch or lock bolt, with curved lip extended to protect frame, finished to match door hardware set, unless otherwise indicated, and as follows:
1. Flat-Lip Strikes: For locks with three-piece antifriction latchbolts, as recommended by manufacturer.
2. Extra-Long-Lip Strikes: For locks used on frames with applied wood casing trim. 3. Aluminum-Frame Strike Box: Provide manufacturer's special strike box fabricated for
aluminum framing. 4. Double-lipped strikes: For locks at double acting doors. Furnish with retractable stop for
rescue hardware applications.
B. Standards: Comply with the following:
1. Strikes for Mortise Locks and Latches: BHMA A156.13.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 12 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
2. Strikes for Bored Locks and Latches: BHMA A156.2. 3. Strikes for Auxiliary Deadlocks: BHMA A156.36. 4. Dustproof Strikes: BHMA A156.16.
2.9 CONVENTIONAL EXIT DEVICES
A. General Requirements: All exit devices specified herein shall meet or exceed the following criteria:
1. At doors not requiring a fire rating, provide devices complying with NFPA 101 and listed and labeled for "Panic Hardware" according to UL305. Provide proper fasteners as required by manufacturer including sex nuts and bolts at openings specified in the Hardware Sets.
2. Where exit devices are required on fire rated doors, provide devices complying with NFPA 80 and with UL labeling indicating "Fire Exit Hardware". Provide devices with the proper fasteners for installation as tested and listed by UL. Consult manufacturer’s catalog and template book for specific requirements.
3. Except on fire rated doors, provide exit devices with hex key dogging device to hold the pushbar and latch in a retracted position. Provide optional keyed cylinder dogging on devices where specified in Hardware Sets.
4. Devices must fit flat against the door face with no gap that permits unauthorized dogging of the push bar. The addition of filler strips is required in any case where the door light extends behind the device as in a full glass configuration.
5. Electromechanical Options: Subject to same compliance standards and requirements as mechanical exit devices, electrified devices to be of type and design as specified in hardware sets. Include any specific controllers when conventional power supplies are not sufficient to provide the proper inrush current.
6. Motorized Electric Latch Retraction: Devices with an electric latch retraction feature must use motors which have a maximum current draw of 600mA. Solenoid driven latch retraction is not acceptable.
7. Lever Operating Trim: Where exit devices require lever trim, furnish manufacturer's heavy duty escutcheon trim with threaded studs for thru-bolts.
a. Lock Trim Design: As indicated in Hardware Sets, provide finishes and designs to match that of the specified locksets.
b. Where function of exit device requires a cylinder, provide a cylinder (Rim or Mortise) as specified in Hardware Sets.
8. Vertical Rod Exit Devices: Where surface or concealed vertical rod exit devices are used at interior openings, provide as less bottom rod (LBR) unless otherwise indicated. Provide dust proof strikes where thermal pins are required to project into the floor.
9. Narrow Stile Applications: At doors constructed with narrow stiles, or as specified in Hardware Sets, provide devices designed for maximum 2” wide stiles.
10. Dummy Push Bar: Nonfunctioning push bar matching functional push bar.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 13 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
11. Extended cycle test: Devices to have been cycle tested in ordinance with ANSI/BHMA 156.3 requirements to 50 million cycles.
12. Rail Sizing: Provide exit device rails factory sized for proper door width application.
13. Through Bolt Installation: For exit devices and trim as indicated in Door Hardware Sets.
14. Hurricane and Tornado Resistance Compliance: Conventional exit devices are to be U.L. listed for windstorm assemblies where applicable. Provide the appropriate hurricane or tornado resistant products that have been independent third party tested, certified, and labeled to meet state and local windstorm building codes applicable to project.
B. Conventional Push Rail Exit Devices (Heavy Duty): ANSI/BHMA A156.3, Grade 1 certified panic and fire exit hardware devices furnished in the functions specified in the Hardware Sets. Exit device latch to be stainless steel, pullman type, with deadlock feature.
1. Manufacturers:
a. Sargent Manufacturing (SA) - 80 Series.
C. Tube Steel Removable Mullions: ANSI/BHMA A156.3 removable steel mullions with malleable-iron top and bottom retainers and a primed paint finish.
1. Provide keyed removable feature where specified in the Hardware Sets.
2. Provide stabilizers and mounting brackets as required.
3. Provide electrical quick connection wiring options as specified in the hardware sets.
4. Manufacturers:
a. Sargent Manufacturing (SA) - 980S Series.
2.10 DOOR CLOSERS
A. All door closers specified herein shall meet or exceed the following criteria:
1. General: Door closers to be from one manufacturer, matching in design and style, with the same type door preparations and templates regardless of application or spring size. Closers to be non-handed with full sized covers including installation and adjusting information on inside of cover.
2. Standards: Closers to comply with UL-10C for Positive Pressure Fire Test and be U.L. listed for use of fire rated doors.
3. Cycle Testing: Provide closers which have surpassed 15 million cycles in a test witnessed and verified by UL.
4. Size of Units: Comply with manufacturer's written recommendations for sizing of door closers depending on size of door, exposure to weather, and anticipated frequency of use. Where closers are indicated for doors required to be accessible to the physically handicapped, provide units complying with ANSI ICC/A117.1.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 14 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
5. Closer Arms: Provide heavy duty, forged steel closer arms unless otherwise indicated in Hardware Sets.
6. Closers shall not be installed on exterior or corridor side of doors; where possible install
closers on door for optimum aesthetics.
7. Closer Accessories: Provide door closer accessories including custom templates, special mounting brackets, spacers and drop plates as required for proper installation. Provide through-bolt and security type fasteners as specified in the hardware sets.
B. Door Closers, Surface Mounted (Heavy Duty): ANSI/BHMA A156.4, Grade 1 surface mounted, heavy duty door closers with complete spring power adjustment, sizes 1 thru 6; and fully operational adjustable according to door size, frequency of use, and opening force. Closers to be rack and pinion type, one piece cast iron or aluminum alloy body construction, with adjustable backcheck and separate non-critical valves for closing sweep and latch speed control. Provide non-handed units standard.
1. Manufacturers:
a. Sargent Manufacturing (SA) - 351 Series.
b. Norton Door Controls (NO) - 7500 Series.
2.11 ELECTROHYDRAULIC DOOR OPERATORS
A. General: Provide low energy operators of size recommended by manufacturer for door size, weight, and movement; for condition of exposure; and for compliance with UL 325. Coordinate operator mechanisms with door operation, hinges, and activation devices.
1. Fire-Rated Doors: Provide door operators for fire-rated door assemblies that comply with NFPA 80 for fire-rated door components and are listed and labeled by a qualified testing agency.
B. Standard: Certified ANSI/BHMA A156.19.
C. Performance Requirements:
1. Opening Force if Power Fails: Not more than 15 lbf required to release a latch if provided, not more than 30 lbf required to manually set door in motion, and not more than 15 lbf required to fully open door.
2. Entrapment Protection: Not more than 15 lbf required to prevent stopped door from closing or opening.
D. Configuration: Surface mounted or in-ground as required. Door operators to control single swinging and pair of swinging doors.
E. Operation: Power opening and spring closing operation capable of meeting ANSI A117.1 accessibility guideline. Provide time delay for door to remain open before initiating closing cycle as required by ANSI/BHMA A156.19. When not in automatic mode, door operator to function as manual door closer with fully adjustable opening and closing forces, with or without electrical power.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 15 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
F. Features: Operator units to have full feature adjustments for door opening and closing force and speed, backcheck, motor assist acceleration from 0 to 30 seconds, time delay, vestibule interface delay, obstruction recycle, and hold open time from 0 up to 30 seconds.
G. Provide outputs and relays on board the operator to allow for coordination of exit device latch retraction, electric strikes, magnetic locks, card readers, safety and motion sensors and specified auxiliary contacts.
H. Brackets and Reinforcements: Manufacturer's standard, fabricated from aluminum with nonferrous shims for aligning system components.
I. Manufacturers: Subject to compliance with requirements, provide products by one of the following:
1. LCN Closers (LC) - 4640 Series. 2. Norton Door Controls (NO) - 6000 Series. 3. Stanley Security Solutions (ST) – D-4990 Series.
2.12 ARCHITECTURAL TRIM
A. Door Protective Trim
1. General: Door protective trim units to be of type and design as specified below or in the Hardware Sets.
2. Size: Fabricate protection plates (kick, armor, or mop) not more than 2" less than door width (LDW) on stop side of single doors and 1” LDW on stop side of pairs of doors, and not more than 1" less than door width on pull side. Coordinate and provide proper width and height as required where conflicting hardware dictates. Height to be as specified in the Hardware Sets.
3. Where plates are applied to fire rated doors with the top of the plate more than 16” above the bottom of the door, provide plates complying with NFPA 80. Consult manufacturer’s catalog and template book for specific requirements for size and applications.
4. Protection Plates: ANSI/BHMA A156.6 certified protection plates (kick, armor, or mop), fabricated from the following:
a. Stainless Steel: 300 grade, 050-inch thick.
5. Options and fasteners: Provide manufacturer's designated fastener type as specified in the Hardware Sets. Provide countersunk screw holes.
6. Manufacturers:
a. Rockwood Products; ASSA ABLOY Architectural Door Accessories (RO).
b. Trimco (TC).
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 16 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
2.13 DOOR STOPS AND HOLDERS
A. General: Door stops and holders to be of type and design as specified below or in the Hardware Sets.
B. Door Stops and Bumpers: ANSI/BHMA A156.16, Grade 1 certified door stops and wall bumpers. Provide wall bumpers, either convex or concave types with anchorage as indicated, unless floor or other types of door stops are specified in Hardware Sets. Do not mount floor stops where they will impede traffic. Where floor or wall bumpers are not appropriate, provide overhead type stops and holders.
1. Manufacturers:
a. Rockwood Products; ASSA ABLOY Architectural Door Accessories (RO).
b. Trimco (TC).
C. Overhead Door Stops and Holders: ANSI/BHMA A156.6, Grade 1 certified overhead stops and holders to be surface or concealed types as indicated in Hardware Sets. Track, slide, arm and jamb bracket to be constructed of extruded bronze and shock absorber spring of heavy tempered steel. Provide non-handed design with mounting brackets as required for proper operation and function.
1. Manufacturers:
a. Rixson Door Controls (RF).
b. Rockwood Products; ASSA ABLOY Architectural Door Accessories (RO).
c. Sargent Manufacturing (SA).
2.14 ARCHITECTURAL SEALS
A. General: Thresholds, weatherstripping, and gasket seals to be of type and design as specified below or in the Hardware Sets. Provide continuous weatherstrip gasketing on exterior doors and provide smoke, light, or sound gasketing on interior doors where indicated. At exterior applications provide non-corrosive fasteners and elsewhere where indicated.
B. Smoke Labeled Gasketing: Assemblies complying with NFPA 105 that are listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for smoke control ratings indicated, based on testing according to UL 1784.
1. Provide smoke labeled perimeter gasketing at all smoke labeled openings.
C. Fire Labeled Gasketing: Assemblies complying with NFPA 80 that are listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for fire ratings indicated, based on testing according to UL-10C.
1. Provide intumescent seals as indicated to meet UL10C Standard for Positive Pressure Fire Tests of Door Assemblies, and NPFA 252, Standard Methods of Fire Tests of Door Assemblies.
D. Sound-Rated Gasketing: Assemblies that are listed and labeled by a testing and inspecting agency, for sound ratings indicated.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 17 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
E. Replaceable Seal Strips: Provide only those units where resilient or flexible seal strips are easily replaceable and readily available from stocks maintained by manufacturer.
F. Manufacturers:
1. Pemko Products; ASSA ABLOY Architectural Door Accessories (PE). 2. Reese Enterprises, Inc. (RE).
2.15 ELECTRONIC ACCESSORIES
A. Power Supplies: Provide Nationally Recognized Testing Laboratory Listed 12VDC or 24VDC (field selectable) filtered and regulated power supplies. Include battery backup option with integral battery charging capability in addition to operating the DC load in event of line voltage failure. Provide the least number of units, at the appropriate amperage level, sufficient to exceed the required total draw for the specified electrified hardware and access control equipment.
1. Manufacturers:
a. Sargent Manufacturing (SA) - 3500 Series.
b. Security Door Controls (SD) - 630 Series.
c. Securitron (SU) - BPS Series.
2.16 FABRICATION
A. Fasteners: Provide door hardware manufactured to comply with published templates generally prepared for machine, wood, and sheet metal screws. Provide screws according to manufacturers recognized installation standards for application intended.
2.17 FINISHES
A. Standard: Designations used in the Hardware Sets and elsewhere indicate hardware finishes complying with ANSI/BHMA A156.18, including coordination with traditional U.S. finishes indicated by certain manufacturers for their products.
B. Provide quality of finish, including thickness of plating or coating (if any), composition, hardness, and other qualities complying with manufacturer's standards, but in no case less than specified by referenced standards for the applicable units of hardware
C. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 18 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine scheduled openings, with Installer present, for compliance with requirements for installation tolerances, labeled fire door assembly construction, wall and floor construction, and other conditions affecting performance.
B. Notify architect of any discrepancies or conflicts between the door schedule, door types, drawings and scheduled hardware. Proceed only after such discrepancies or conflicts have been resolved in writing.
3.2 PREPARATION
A. Hollow Metal Doors and Frames: Comply with ANSI/DHI A115 series.
B. Wood Doors: Comply with ANSI/DHI A115-W series.
3.3 INSTALLATION
A. Install each item of mechanical and electromechanical hardware and access control equipment to comply with manufacturer's written instructions and according to specifications.
1. Installers are to be trained and certified by the manufacturer on the proper installation and adjustment of fire, life safety, and security products including: hanging devices; locking devices; closing devices; and seals.
B. Mounting Heights: Mount door hardware units at heights indicated in following applicable publications, unless specifically indicated or required to comply with governing regulations:
1. Standard Steel Doors and Frames: DHI's "Recommended Locations for Architectural Hardware for Standard Steel Doors and Frames."
2. Wood Doors: DHI WDHS.3, "Recommended Locations for Architectural Hardware for Wood Flush Doors."
3. Where indicated to comply with accessibility requirements, comply with ANSI A117.1 "Accessibility Guidelines for Buildings and Facilities."
4. Provide blocking in drywall partitions where wall stops or other wall mounted hardware is located.
C. Retrofitting: Install door hardware to comply with manufacturer's published templates and written instructions. Where cutting and fitting are required to install door hardware onto or into surfaces that are later to be painted or finished in another way, coordinate removal, storage, and reinstallation of surface protective trim units with finishing work specified in Division 9 Sections. Do not install surface-mounted items until finishes have been completed on substrates involved.
D. Thresholds: Set thresholds for exterior and acoustical doors in full bed of sealant complying with requirements specified in Division 7 Section "Joint Sealants."
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 19 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
E. Storage: Provide a secure lock up for hardware delivered to the project but not yet installed. Control the handling and installation of hardware items so that the completion of the work will not be delayed by hardware losses before and after installation.
3.4 FIELD QUALITY CONTROL
A. Field Inspection: Supplier will perform a final inspection of installed door hardware and state in report whether work complies with or deviates from requirements, including whether door hardware is properly installed, operating and adjusted.
3.5 ADJUSTING
A. Initial Adjustment: Adjust and check each operating item of door hardware and each door to ensure proper operation or function of every unit. Replace units that cannot be adjusted to operate as intended. Adjust door control devices to compensate for final operation of heating and ventilating equipment and to comply with referenced accessibility requirements.
3.6 CLEANING AND PROTECTION
A. Protect all hardware stored on construction site in a covered and dry place. Protect exposed hardware installed on doors during the construction phase. Install any and all hardware at the latest possible time frame.
B. Clean adjacent surfaces soiled by door hardware installation.
C. Clean operating items as necessary to restore proper finish. Provide final protection and maintain conditions that ensure door hardware is without damage or deterioration at time of owner occupancy.
3.7 DEMONSTRATION
A. Instruct Owner's maintenance personnel to adjust, operate, and maintain mechanical and electromechanical door hardware.
3.8 DOOR HARDWARE SETS
A. The hardware sets represent the design intent and direction of the owner and architect. They are a guideline only and should not be considered a detailed hardware schedule. Discrepancies, conflicting hardware and missing items should be brought to the attention of the architect with corrections made prior to the bidding process. Omitted items not included in a hardware set should be scheduled with the appropriate additional hardware required for proper application and functionality.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 20 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
B. Manufacturer’s Abbreviations:
1. MK - McKinney
2. MR - Markar
3. RO - Rockwood
4. SA - Sargent
5. RF - Rixson
6. NO - Norton
7. PE - Pemko
8. HD - HID
9. SU - Securitron
10. LU - Lund Equipment Co., Inc.
Hardware Sets
Set: 1.0
Doors: 619B, 619C, 619D, 637A, 637B, 637C, 709A, 709B
Description: Exterior Aluminum Card Access / Exit Pair
2 Continuous Hinge FM100 7'0 EL-EPTL 628 MR ⚡
1 Exit Device (electronic) 10 21 55 56 AD8410 113 x 862 GMK
US32D SA
1 Concealed Vert Rod Exit 16 55 AD8410 862 US32D SA ⚡ 2 Door Closer SRI 351 CPS 581-2 EN SA
1 Threshold 171AK WS10SS PE
2 Sweep 315CN PE
1 Door Position Switch 3287 SA
Notes: All exterior doors on this project shall meet FBC standards for windstorm. The door hardware specified is listed as a basis of design. If alternate hardware is proposed, please provide third-party test results and compliance information to architect. Perimeter gasket by frame manufacturer. Door contact switch indicates propped door condition.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 21 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
Set: 2.0
Doors: 618, 700BB
Description: Exterior Aluminum Card Access / Exit Pair + ADA Operators
2 Continuous Hinge FM100 7'0 EL-EPTL 628 MR ⚡
1 Exit Device (electronic) 10 21 55 56 AD8410 113 x 862 GMK
US32D SA
1 Exit Device (electronic) 55 56 AD8410 862 US32D SA
2 Door Operator 6070 D 689 NO ⚡ 1 Threshold 171AK WS10SS PE
2 Sweep 315CN PE
2 ElectroLynx Harness QC-C1500P Hinge to J-Box MK ⚡ 2 ElectroLynx Harness QC-C012 Hinge to Device MK ⚡ 2 Door Position Switch 3287 SA
1 Wall Proximity Reader Match Owner's Standard HD
2 ADA Wall Switch 506 NO ⚡ 1 Power Supply BPS-24 x Amperage as required SU ⚡
Notes: All exterior doors on this project shall meet FBC standards for windstorm. The door hardware specified is listed as a basis of design. If alternate hardware is proposed, please provide third-party test results and compliance information to architect. Perimeter gasket by frame manufacturer. NOTE: Access control panel and security management software by security integrator. Prep door and hinge jamb for electromechanical device. Provide flex conduit and in door & hinge jamb. OPERATION: After Hours: Card Reader outside or inside pushpad retract latchbolts and cycle operator on one leaf. School Hours: Door control panel timer holds both latchbbolts retracted and activates outside ADA switch. AADA switch either side cycles operators. Electronic device function is fail-secure with inside RX switch in rail. Active device has outside key override. Inside rail always allows egress. Door position is monitored by magnetic switch for authorized egress.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 22 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
Set: 3.0
Doors: 700BA
Description: Exterior Aluminum Entry / Exit Pair
2 Continuous Hinge FM100 7'0 628 MR
1 Exit Device 10 16 21 AD8410 113 x 862 GMK
US32D SA
1 Exit Device 10 16 21 AD8410 862 US32D SA
2 Drop Plate 351D EN SA
2 Door Closer SRI 351 CPS 581-2 EN SA
1 Threshold 171AK WS10SS PE
2 Sweep 315CN PE
2 Door Position Switch 3287 SA
Notes: All exterior doors on this project shall meet FBC standards for windstorm. The door hardware specified is listed as a basis of design. If alternate hardware is proposed, please provide third-party test results and compliance information to architect. Perimeter gasket by frame manufacturer. Door contact switch indicates propped door condition.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 23 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
Set: 4.0
Doors: 705B, 708B
Description: Exterior Aluminum / Exit
1 Continuous Hinge FM100 7'0 EL-EPTL 628 MR ⚡ 1 Exit Device HC 10 21 55 56 8804 862 GMK US32D SA ⚡ 1 Door Closer SRI 351 P10 EN SA
1 Kick Plate K1050 8" High US32D RO
1 Threshold 171AK WS10SS PE
1 Jamb Gasketing 290AS PE
1 Head Gasketing 2891AS PE
1 Sweep 315CN PE
1 Door Position Switch 3287 SA
Notes: All exterior doors on this project shall meet FBC standards for windstorm. The door hardware specified is listed as a basis of design. If alternate hardware is proposed, please provide third-party test results and compliance information to architect.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 24 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
Set: 5.0
Doors: 710B, 712B
Description: Exterior Card Access / Exit
1 Hinge (heavy weight) T4A3386 QC12 4-1/2" x 4-1/2" US32D MK ⚡ 2 Hinge (heavy weight) T4A3386 NRP 4-1/2" x 4-1/2" US32D MK
1 Exit Device HC 10 21 55 56 8804 862 GMK US32D SA ⚡ 1 Door Closer SRI 351 P10 EN SA
1 Kick Plate K1050 8" High US32D RO
1 ElectroLynx Harness QC-C1500P Hinge to J-Box MK ⚡ 1 ElectroLynx Harness QC-C012 Hinge to Device MK ⚡ 1 Door Position Switch 3287 SA
1 Wall Proximity Reader Match Owner's Standard HD
1 Power Supply BPS-24 x Amperage as required SU ⚡
Notes: All exterior doors on this project shall meet FBC standards for windstorm. The door hardware specified is listed as a basis of design. If alternate hardware is proposed, please provide third-party test results and compliance information to architect. Access control panel and security software by security contractor. Prep door and hinge jamb for electromechanical device. Provide Wire Harness in door. OPERATION: Card reader outside temporarily retracts latchbolt - auto relock. Device is fail-secure with inside RX switch and outside key override. Inside pushbar always allows egress. Door position is monitored by magnetic switch for authorized egress.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 25 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
Set: 6.0
Doors: 617B
Description: Exterior Electrical Room Exit - NEC
3 Hinge TA2314 NRP 4-1/2" x 4-1/2" US32D MK
1 Rim Exit Device HC 10 21 86 8804 PSB GGMK US32D SA
1 Door Closer SRI 351 CPSH EN SA
1 Threshold 1715AK WS10SS PE
1 Gasketing S88D PE
1 Sweep 315CN PE
1 Door Position Switch 3287 SA
Notes: All exterior doors on this project shall meet FBC standards for windstorm. The door hardware specified is listed as a basis of design. If alternate hardware is proposed, please provide third-party test results and compliance information to architect. Door contact switch indicates propped door condition - by security subcontractor.
Set: 7.0
Doors: 700A
Description: Exterior Exit-Only Pair
6 Hinge (heavy weight) T4A3386 NRP 4-1/2" x 4-1/2" US32D MK
1 Removable Mullion HC980 PC SA
2 Exit Device (exit only) HC LD 8810 US32D SA
2 Door Closer SRI 351 CPS EN SA
2 Kick Plate K1050 8" High US32D RO
1 Threshold 171AK WS10SS PE
2 Jamb Gasketing 290AS PE
1 Head Gasketing 2891AS PE
2 Sweep 315CN PE
2 Door Position Switch 3287 SA
Notes: All exterior doors on this project shall meet FBC standards for windstorm. The door hardware specified is listed as a basis of design. If alternate hardware is proposed, please provide third-party test results and compliance information to architect. Door contact switch indicates propped door condition - by security subcontractor.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 26 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
Set: 8.0
Doors: 714
Description: Exterior Mechanical Room Pair
6 Hinge TA2314 NRP 4-1/2" x 4-1/2" US32D MK
2 Surface Bolt 988 Bright Zinc
SA
1 Storeroom Lock 10 21 8251 LNL US26D SA
1 Surf Overhead Hold Open 9-X26 630 RF
1 Door Closer SRI 351 CPSH EN SA
1 Threshold 1715AK WS10SS PE
2 Jamb Gasketing 290AS PE
1 Head Gasketing 2891AS PE
1 Astragal Seal S771D PE
2 Door Position Switch 3287 SA
Notes: All exterior doors on this project shall meet FBC standards for windstorm. The door hardware specified is listed as a basis of design. If alternate hardware is proposed, please provide third-party test results and compliance information to architect. Door contact switch indicates propped door condition - by security subcontractor. Overlapping astragal by door manufacturer.
Set: 9.0
Doors: 600
Description: Aluminum Entry / Exit
1 Continuous Hinge FM100 7'0 628 MR
1 Exit Device 10 16 21 AD8510 862 US32D SA
1 Door Closer TB 351 CPS 581-2 EN SA
Notes: Perimeter gasket by frame manufacturer.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 27 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
Set: 10.0
Doors: 619A
Description: Card Access / Exit Pair
4 Hinge (heavy weight) T4A3786 NRP 4-1/2" x 4-1/2" US26D MK
2 Hinge (heavy weight) T4A3786 QC12 4-1/2" x 4-1/2" US26D MK ⚡ 1 Removable Mullion L980S PC SA
1 Rim Exit Device 10 21 55 56 8804 862 GMK US32D SA ⚡ 1 Rim Exit Device 10 16 21 55 8810 862 GMK US32D SA ⚡ 1 Cylinder 10 21 980C1 GMK US26D SA
2 Door Closer TB 351 CPS EN SA
2 Kick Plate K1050 8" High US32D RO
2 Silencer 608 RO
2 ElectroLynx Harness QC-C1500P Hinge to J-Box MK ⚡ 2 ElectroLynx Harness QC-C012 Hinge to Device MK ⚡ 2 Door Position Switch 3287 SA
1 Wall Proximity Reader Match Owner's Standard HD
1 Power Supply BPS-24 x Amperage as required SU ⚡
Notes: Access control panel and security software by security contractor. Prep door and hinge jamb for electromechanical device. Provide Wire Harness in door. OPERATION: Card reader outside temporarily retracts latchbolt - auto relock. Device is fail-secure with inside RX switch and outside key override. Inside pushbar always allows egress. Pushbutton (location to be determined by owner) required at desk for allowing entrance.
Set: 11.0
Doors: 705A
Description: Entry / Exit Pair
6 Hinge (heavy weight) T4A3786 NRP 4-1/2" x 4-1/2" US26D MK
1 Removable Mullion L980S PC SA
1 Rim Exit Device 10 16 21 8810 862 GMK US32D SA
1 Rim Exit Device 10 16 21 8804 862 GMK US32D SA
1 Cylinder 10 21 980C1 GMK US26D SA
2 Door Closer TB 351 P10 EN SA
2 Kick Plate K1050 8" High US32D RO
2 Wall Stop 401 EXP US26D RO
2 Silencer 608 RO
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 28 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
Set: 12.0
Doors:
Description: Electrical Room Exit - NEC
3 Hinge TA2714 NRP 4-1/2" x 4-1/2" US26D MK
1 Rim Exit Device 10 21 76 8804 ETL GMK US32D SA
1 Door Closer TB 351 P10 EN SA
1 Wall Stop 401 EXP US26D RO
1 Gasketing S88D PE
Set: 13.0
Doors: 700B, 700C
Description: Rated Classroom Function / Exit Pair
6 Hinge (heavy weight) T4A3786 NRP 4-1/2" x 4-1/2" US26D MK
1 Removable Mullion 12-L980 PC SA
1 Exit Device (exit only) 12 8810 US32D SA
1 Rim Exit Device 12 21 8813 ETL GMK US32D SA
1 Cylinder 10 21 980C1 GMK US26D SA
2 Door Closer TB 351 CPS EN SA
2 Kick Plate K1050 8" High US32D RO
1 Gasketing S88D PE
1 Astragal Seal S771D PE
Set: 14.0
Doors: 710A, 712A
Description: Rated Classroom Function Exit
3 Hinge (heavy weight) T4A3786 NRP 4-1/2" x 4-1/2" US26D MK
1 Exit Device 12 21 8813 ETL US32D SA
1 Door Closer TB 351 P10 EN SA
1 Kick Plate K1050 8" High US32D RO
1 Wall Stop 409 or 442 as required US32D RO
1 Gasketing S88D PE
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 29 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
Set: 15.0
Doors:
Description: Storeroom Function Pair
6 Hinge TA2714 NRP 4-1/2" x 4-1/2" US26D MK
2 Flush Bolt 555 US26D RO
1 Dust Proof Strike 570 US26D RO
1 Storeroom Lock 21 28 11G04 LL US26D SA
2 Surface Overhead Holder 9-X26 652 RF
1 Astragal 357SS PE
2 Silencer 608 RO
Set: 16.0
Doors: 604, 624
Description: Mechanical Room Pair
6 Hinge TA2714 NRP 4-1/2" x 4-1/2" US26D MK
2 Flush Bolt 555 US26D RO
1 Dust Proof Strike 570 US26D RO
1 Storeroom Lock 21 28 76 11G04 LL US26D SA
1 Surface Overhead Holder 9-X26 652 RF
1 Door Closer TB 351 CPSH EN SA
1 Gasketing S88D PE
1 Astragal 357SS PE
1 Astragal Seal S771D PE
Notes: Overlapping astragal by door manufacturer.
Set: 17.0
Doors: 613BA, 704, 705AA, 708AA
Description: Storeroom Function
3 Hinge TA2714 NRP 4-1/2" x 4-1/2" US26D MK
1 Storeroom Lock 21 28 11G04 LL US26D SA
1 Wall Stop 409 or 442 as required US32D RO
3 Silencer 608 RO
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 30 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
Set: 18.0
Doors: 617A, 612A, 632A
Description: Storeroom Function
3 Hinge TA2714 NRP 4-1/2" x 4-1/2" US26D MK
1 Storeroom Lock 21 28 11G04 LL US26D SA
1 Door Closer @ 617A only TB 351 O EN SA
1 Surface Overhead Holder 10-X26 652 RF
3 Silencer 608 RO
Set: 19.0
Doors: 707
Description: Storeroom Function + Closer
3 Hinge TA2714 NRP 4-1/2" x 4-1/2" US26D MK
1 Storeroom Lock 21 28 11G04 LL US26D SA
1 Door Closer TB 351 O EN SA
1 Wall Stop 409 or 442 as required US32D RO
3 Silencer 608 RO
1 Wall Mounted Key Cabinet 150% Capacity with Tags LU
Notes: Install closer on room side. Install key cabinet as directed by owner.
Set: 20.0
Doors: 602, 622, 706
Description: Electrical Room
3 Hinge TA2714 NRP 4-1/2" x 4-1/2" US26D MK
1 Storeroom Lock 21 28 76 11G04 LL US26D SA
1 Door Closer TB 351 O EN SA
1 Wall Stop 409 or 442 as required US32D RO
1 Gasketing S88D PE
Notes: Install closer on room side.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 31 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
Set: 21.0
Doors: 700DA Description: Rated Storeroom Function - Storage
3 Hinge TA2714 NRP 4-1/2" x 4-1/2" US26D MK
1 Storeroom Lock 21 28 11G04 LL US26D SA
1 Door Closer TB 351 CPS EN SA
1 Gasketing S88D PE
Set: 22.0
Doors: 700AA, 700CA
Description: Mechanical Room Pair
6 Hinge TA2714 NRP 4-1/2" x 4-1/2" US26D MK
2 Flush Bolt 555 US26D RO
1 Dust Proof Strike 570 US26D RO
1 Storeroom Lock 21 28 76 11G04 LL US26D SA
2 Surface Overhead Stop 9-X36 652 RF
1 Door Closer 351 O EN SA
1 Gasketing S88D PE
1 Astragal 357SS PE
1 Astragal Seal S771D PE
Notes: Overlapping astragal by door manufacturer.
Set: 23.0
Doors: 600A, 600B, 600C, 600D
Description: Office / Entry Function
3 Hinge TA2714 NRP 4-1/2" x 4-1/2" US26D MK
1 Office Lock 21 28 11G05 LL US26D SA
1 Wall Stop 409 or 442 as required US32D RO
3 Silencer 608 RO
1 Coat Hook 796 US26D RO
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 32 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
Set: 24.0
Doors: 601, 603, 605, 609, 711, 713
Description: Classroom Function
3 Hinge TA2714 NRP 4-1/2" x 4-1/2" US26D MK
1 Office Lock 21 28 11G05 LL US26D SA
1 Wall Stop 409 or 442 as required US32D RO
3 Silencer 608 RO
Set: 25.0
Doors: 601A, 606AA, 606AB, 607A, 607B, 611, 613A, 613B, 615, 616, 620, 621, 621A, 623, 625, 626AA, 626AB, 627, 629, 631, 633A, 633B, 635A, 635B, 636, 705BA, 708BA
Description: Classroom Function
3 Hinge TA2714 NRP 4-1/2" x 4-1/2" US26D MK
1 Classroom Lock 21 28 11G37 LL US26D SA
1 Surface Overhead Stop 9-X36 652 RF
3 Silencer 608 RO
Set: 26.0
Doors: 708A
Description: Classroom Function Pair - Gasketed
6 Hinge TA2714 NRP 4-1/2" x 4-1/2" US26D MK
1 Flush Bolt 2962 US26D RO
1 Dust Proof Strike 570 US26D RO
1 Classroom Lock 21 28 11G37 LL US26D SA
1 Coordinator 2672 US28 RO
2 Mounting Bracket 2601 US28 RO
2 Door Closer TB 351 P10 EN SA
2 Wall Stop 409 or 442 as required US32D RO
1 Gasketing S88D PE
1 Astragal 357SS PE
1 Astragal Seal S771D PE
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 33 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
Set: 27.0
Doors: 606, 610, 626, 630
Description: Classroom Function
3 Hinge (heavy weight) T4A3786 NRP 4-1/2" x 4-1/2" US26D MK
1 Classroom Lock 21 28 11G37 LL US26D SA
1 Wall Stop 409 or 442 as required US32D RO
Set: 28.0
Doors: 613AA, 615AA, 615BA, 711A, 713A
Description: Privacy Function
3 Hinge TA2314 NRP 4-1/2" x 4-1/2" US32D MK
1 Privacy Set 28 11U65 LL US26D SA
1 Mop Plate K1050 5" High US32D RO
1 Wall Stop 409 or 442 as required US32D RO
3 Silencer 608 RO
1 Coat Hook 796 US26D RO
Set: 29.0
Doors: 608, 628, 701
Description: Privacy Function + Closer
3 Hinge TA2314 NRP 4-1/2" x 4-1/2" US32D MK
1 Privacy Set 28 11U65 LL US26D SA
1 Door Closer TB 351 O EN SA
1 Mop Plate K1050 5" High US32D RO
1 Kick Plate K1050 8" High US32D RO
1 Wall Stop 409 or 442 as required US32D RO
3 Silencer 608 RO
1 Coat Hook 796 US26D RO
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 DOOR HARDWARE 08 71 00 - 34 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
Set: 30.0
Doors: 702, 703
Description: Push-Pull + Deadlock
3 Hinge (heavy weight) T4A3386 NRP 4-1/2" x 4-1/2" US32D MK
1 Mortise Deadlock 21 4878 GMK US26D SA
1 Pull Plate BF T111x70C US32D RO
1 Push Plate 70F US32D RO
1 Door Closer TB 351 P10 EN SA
1 Kick Plate K1050 8" High US32D RO
1 Wall Stop 409 or 442 as required US32D RO
3 Silencer 608 RO
Set: 31.0
Description: Chain Link Gates
1 Padlock 10 21 758 C GMK SA
Notes: Balance of hardware by door manufacturer.
END OF SECTION 08 71 00
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 STANDARD LOCKERS 10 51 00 - 1
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
SECTION 10 51 00 STANDARD LOCKERS
PART 1 - GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
1.2 SUMMARY
A. This Section Includes:
1. Lockers. 2. Locker Benches.
1.3 PREINSTALLATION MEETINGS
A. Preinstallation Conference: Conduct conference at Project site.
1.4 ACTION SUBMITTALS
A. Product Data: For each type of metal locker.
1. Include construction details, material descriptions, dimensions of individual components and profiles, and finishes for each type of metal locker and bench.
B. Shop Drawings: For metal lockers.
1. Include plans, elevations, sections, details, and attachments to other work. 2. Show locker trim and accessories. 3. Include locker identification system and numbering sequence.
C. Samples: For each color specified, in manufacturer's standard size.
D. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors available.
E. Samples for Verification: For the following products, in manufacturer's standard size:
1. Lockers and equipment.
F. Product Schedule: For lockers. Use same designations indicated on Drawings.
1.5 INFORMATIONAL SUBMITTALS
A. Qualification Data: For Installer.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 STANDARD LOCKERS 10 51 00 - 2
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
B. Sample Warranty: For special warranty.
1.6 CLOSEOUT SUBMITTALS
A. Maintenance Data: For adjusting, repairing, and replacing locker doors and latching mechanisms to include in maintenance manuals.
1.7 MAINTENANCE MATERIAL SUBMITTALS
A. Furnish extra materials that match products installed and that are packaged with protective covering for storage and identified with labels describing contents.
1. Full-size units of the following metal locker hardware items equal to 10 percent of amount installed for each type and finish installed, but no fewer than five units:
a. Identification plates. b. Hooks.
1.8 DELIVERY, STORAGE, AND HANDLING
A. Do not deliver metal lockers until spaces to receive them are clean, dry, and ready for their installation.
B. Deliver master and control keys combination control charts to Owner by registered mail or overnight package service.
1.9 FIELD CONDITIONS
A. Field Measurements: Verify actual dimensions of recessed openings by field measurements before fabrication.
1.10 COORDINATION
A. Coordinate sizes and locations of bases for metal lockers.
B. Coordinate sizes and locations of framing, blocking, furring, reinforcements, and other related units of work specified in other Sections to ensure that metal lockers can be supported and installed as indicated.
1.11 WARRANTY
A. Special Warranty: Manufacturer agrees to repair or replace components of metal lockers that fail in materials or workmanship, excluding finish, within specified warranty period.
1. Failures include, but are not limited to, the following:
a. Structural failures. b. Faulty operation of latches and other door hardware.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 STANDARD LOCKERS 10 51 00 - 3
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
2. Damage from deliberate destruction and vandalism is excluded. 3. Warranty Period for Knocked-Down Welded Metal Lockers: Two years lifetime from date
of Substantial Completion.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
A. Source Limitations: Obtain metal lockers, locker benches, and accessories from single source from single locker manufacturer.
2.2 MANUFACTURER
A. Basis-of-Design Product: Subject to compliance with requirements, provide DeBourgh Mfg. Co.; Corregidor Corridor Locker, P.E. or a comparable product by one of the following:
1. Penco Products, Inc. 2. Republic Storage Systems, LLC. 3. Lockers MFG. 4. Art Metal Products.
B. Configurations: As Indicated.
2.3 MATERIALS AND CONSTRUCTION
A. Types: Lockers shall be pre-assembled in multiple column units to meet job conditions. Lockers to be installed in the field by bolting units together.
B. Materials: Sheet steel used in fabrication shall be galvanized, prime grade, free from scale and imperfections. Locking mechanisms and hooks must be zinc plated. Installation hardware to be zinc plated. Locker construction shall be of the knocked-down welded type.
C. Body of Lockers:
1. Tops, Bottoms, and Sides: Exterior sides constructed of 16 gauge (Ga) domestic cold rolled sheet steel for maximum durability with 18 Ga intermediate partitions.
2. Backs and Intermediate Partitions: Solid sheet of 18 Ga cold rolled sheet steel bolted or riveted to frames of sides and intermediate partitions.
3. Shelves: Constructed of 18 Ga cold rolled sheet steel bolted or riveted to sides and intermediate partition construction. Shelves provided in lockers 60 inches and taller, located to provide a minimum of 12 inches clearance.
4. Tier Dividers: Full depth 16 Ga CRS securely bolted or riveted on all four sides, to combine with tops, bottoms, sides, and intermediate partitions to create four-sided continuous door strike.
D. Doors
1. 16 Ga CRS formed outer panel with double bends on both sides and a single bend on top and bottom with 18 Ga steel formed stiffener panel.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 STANDARD LOCKERS 10 51 00 - 4
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
a. Provide ten (10) additional doors of each locker color selected for Owner’s attic stock.
E. Door Ventilation:
1. Louvered Ventilation, three-dimensional vertical vents formed on fronts and backs of door.
F. Latching:
1. Door containing stainless steel cup recessed into formed door. 2. 12 Ga steel finger lift mechanism. 3. Rubber bumpers riveted to door stops for silent operation 4. Locking device shall be completely recessed in door and be fingertip lift control and shall
include a built-in combination lock with master key.
G. Hinges:
1. 16 Ga continuous piano hinge on the right side of the opening. 2. Hinges welded to door and riveted to locker frame.
H. Sloped Tops:
1. Provide 18 Ga sloped top with 25 degree pitch, attached at factory with concealed fasteners. Slope top to be in addition to standard 16 Ga flat top.
I. Closed Base:
1. Provide 4 inch high, 14 Ga steel base enclosed on all four sides securely bolted or riveted to locker bottom.
J. Reinforced Bottom:
1. Provide 16 Ga spacer channel bolted or riveted to locker bottom from front to back Spacer channel to have full height 1/2-inch ID tube bolted or riveted over anchor holes to eliminate deflection upon locker installation.
K. Hooks:
1. Hooks to be heavy duty forged steel with ball ends and zinc plated. 2. Provide two single wall hooks and one double ceiling hook in each locker opening 20
inches or taller. 3. Numbering:
a. Furnish each locker with black anodized laser-etched aluminum number plate. b. Locate number plate near center of each door. c. Owner to furnish numbering sequence.
L. Finish: Units shall be thoroughly cleaned, given a bonding and rust inhibitive treatment, electrostatically sprayed with a heavy coat of high quality enamel on epoxy, then baked at 300-325 degrees F.
M. Provide fillers, trim, and necessary accessories.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 STANDARD LOCKERS 10 51 00 - 5
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
N. Opening mechanism for ADA accessible lockers shall be in strict accordance with ADA Accessibility requirements; with steel padlock loop that projects through metal locker door.
2.4 LOCKER BENCHES
A. Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to the following:
1. ASI Storage Solutions; ASI Group. 2. Lyon Workspace Products, LLC. 3. Penco Products, Inc.
B. Provide bench units with overall assembly height of 17-1/2 inches.
C. Bench Tops: Manufacturer's standard one-piece units, with rounded corners and edges.
1. Size: Minimum 9-1/2 inches wide by 1-1/2 inches thick except provide minimum 20-inch- wide tops where accessible benches are indicated.
2. Solid Plastic - HDPE High Density Polyethylene with homogenous color and a matte finish texture.
a. Color: As selected by Architect from manufacturer's full range. b. Length: as indicated.
D. Fixed-Bench Pedestals: Manufacturer's standard supports, with predrilled fastener holes for attaching bench top and anchoring to floor, complete with fasteners and anchors, and as follows:
1. Tubular Steel: 1-1/2-inch- diameter steel tubing threaded on both ends, with standard pipe flange at top and base plate for casting into concrete slab; with baked-enamel or powder-coat finish.
a. Color: As selected by Architect from manufacturer's full range.
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine walls, floors, and support bases, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of the Work.
B. Prepare written report, endorsed by Installer, listing conditions detrimental to performance of the Work.
C. Proceed with installation only after unsatisfactory conditions have been corrected.
3.2 INSTALLATION
A. General: Install lockers level, plumb, and true; shim as required, using concealed shims.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 STANDARD LOCKERS 10 51 00 - 6
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
1. Anchor locker runs at ends and at intervals recommended by manufacturer, but not more than 36 inches o.c. Using concealed fasteners, install anchors through backup reinforcing plates, channels, or blocking as required to prevent metal distortion.
2. Anchor single rows of metal lockers to walls near top of lockers and to floor. 3. Anchor back-to-back metal lockers to floor.
B. Knocked-Down Lockers: Assemble with manufacturer's standard fasteners, with no exposed fasteners on door faces or face frames.
B. Welded Construction: Factory preassemble metal lockers by welding all joints, seams, and connections; with no bolts, nuts, screws, or rivets used in assembly of main locker groups. Factory weld main locker groups into one-piece structures. Grind exposed welds smooth and flush.
C. Equipment:
1. Attach hooks with at least two fasteners. 2. Identification Plates: Identify metal lockers with identification indicated on Drawings.
a. Attach plates to each locker door, near top, centered, with at least two aluminum rivets.
b. Attach plates to upper shelf of each open-front metal locker, centered, with a least two aluminum rivets.
D. Trim: Fit exposed connections of trim, fillers, and closures accurately together to form tight, hairline joints, with concealed fasteners and splice plates.
1. Attach recess trim to recessed metal lockers with concealed clips. 2. Attach filler panels with concealed fasteners. Locate filler panels where indicated on
Drawings. 3. Attach sloping-top units to metal lockers, with closures at exposed ends. 4. Attach boxed solid plastic end panels using concealed fasteners to conceal exposed
ends of nonrecessed metal lockers. 5. Attach finished solid plastic end panels using fasteners only at perimeter to conceal
exposed ends of nonrecessed metal lockers.
E. Fixed Benches: Provide no fewer than two pedestals for each bench, uniformly spaced not more than 72 inches apart. Bases shall be cast into concrete slab and protected, after other installation of adjacent materials is complete, fasten bench tops to bases and protect from damage.
3.3 ADJUSTING
A. Clean, lubricate, and adjust hardware. Adjust doors and latches to operate easily without binding. Verify that integral locking devices operate properly.
3.4 PROTECTION
A. Protect metal lockers from damage, abuse, dust, dirt, stain, or paint. Do not permit use during construction.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 STANDARD LOCKERS 10 51 00 - 7
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
B. Touch up marred finishes, or replace metal lockers that cannot be restored to factory-finished appearance. Use only materials and procedures recommended or furnished by locker manufacturer.
END OF SECTION 10 51 00
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 P.E. LOCKERS 10 51 13 - 1
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
SECTION 10 51 13 P.E. LOCKERS
PART 1 - GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
1.2 SUMMARY
1. Lockers. 2. Locker Benches.
1.3 PREINSTALLATION MEETINGS
A. Preinstallation Conference: Conduct conference at Project site.
1.4 ACTION SUBMITTALS
A. Product Data: For each type of metal locker.
1. Include construction details, material descriptions, dimensions of individual components and profiles, and finishes for each type of metal locker and bench.
B. Shop Drawings: For metal lockers.
1. Include plans, elevations, sections, details, and attachments to other work. 2. Show locker trim and accessories. 3. Include locker identification system and numbering sequence.
C. Samples: For each color specified, in manufacturer's standard size.
D. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors available.
E. Samples for Verification: For the following products, in manufacturer's standard size:
1. Lockers and equipment.
F. Product Schedule: For lockers. Use same designations indicated on Drawings.
1.5 INFORMATIONAL SUBMITTALS
A. Qualification Data: For Installer.
B. Sample Warranty: For special warranty.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 P.E. LOCKERS 10 51 13 - 2
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
1.6 CLOSEOUT SUBMITTALS
A. Maintenance Data: For adjusting, repairing, and replacing locker doors and latching mechanisms to include in maintenance manuals.
1.7 MAINTENANCE MATERIAL SUBMITTALS
A. Furnish extra materials that match products installed and that are packaged with protective covering for storage and identified with labels describing contents.
1. Full-size units of the following metal locker hardware items equal to 10 percent of amount installed for each type and finish installed, but no fewer than five units:
a. Locks. b. Identification plates. c. Hooks.
1.8 DELIVERY, STORAGE, AND HANDLING
A. Do not deliver metal lockers until spaces to receive them are clean, dry, and ready for their installation.
B. Deliver master and control keys combination control charts to Owner by registered mail or overnight package service.
1.9 FIELD CONDITIONS
A. Field Measurements: Verify actual dimensions of recessed openings by field measurements before fabrication.
1.10 COORDINATION
A. Coordinate sizes and locations of bases for metal lockers.
B. Coordinate sizes and locations of framing, blocking, furring, reinforcements, and other related units of work specified in other Sections to ensure that metal lockers can be supported and installed as indicated.
1.11 WARRANTY
A. Special Warranty: Manufacturer agrees to repair or replace components of metal lockers that fail in materials or workmanship, excluding finish, within specified warranty period.
1. Failures include, but are not limited to, the following:
a. Structural failures. b. Faulty operation of latches and other door hardware.
2. Damage from deliberate destruction and vandalism is excluded.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 P.E. LOCKERS 10 51 13 - 3
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
3. Warranty Period for Knocked-Down Welded Metal Lockers: Two yearsLifetime from date of Substantial Completion.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
A. Source Limitations: Obtain metal lockers, locker benches, and accessories from single source from single locker manufacturer.
1. Obtain locks from single lock manufacturer.
2.2 MANUFACTURER
A. Basis-of-Design Product: Subject to compliance with requirements, provide DeBourgh Mfg. Co. Art Metal Products; Corregidor P.E. Locker models “Champ” and “Box,” at locations indicted, or a comparable product by one of the following:
1. Penco Products, Inc. 2. Republic Storage Systems, LLC. 3. Lockers MFG.
B. Configurations: As Indicated.
2.3 MATERIALS AND CONSTRUCTION
A. Types: Lockers shall be pre-assembled in multiple column units to meet job conditions. Lockers to be installed in the field by bolting units together.
B. Materials: Sheet steel used in fabrication shall be galvanized, prime grade, free from scale and imperfections. Locking mechanisms and hooks must be zinc plated. Installation hardware to be zinc plated. Locker construction shall be of the knocked-downwelded type.
C. Body of Lockers:
1. Tops, Bottoms, and Sides: Exterior sides constructed of 16 gauge (Ga) domestic cold rolled sheet steel for maximum durability with 18 Ga intermediate partitions.
2. Backs and Intermediate Partitions: Solid sheet of 18 Ga cold rolled sheet steel bolted or riveted to frames of sides and intermediate partitions.
3. Shelves: Constructed of 18 Ga cold rolled sheet steel bolted or riveted to sides and intermediate partition construction. Shelves provided in lockers 60 inches and taller, located to provide a minimum of 12 inches clearance.
4. Tier Dividers: Full depth 16 Ga CRS securely bolted or riveted on all four sides, to combine with tops, bottoms, sides, and intermediate partitions to create four-sided continuous door strike.
D. Doors
1. 16 Ga CRS formed outer panel with double bends on both sides and a single bend on top and bottom with 18 Ga steel formed stiffener panel.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 P.E. LOCKERS 10 51 13 - 4
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
a. Provide ten (10) additional doors of each locker color selected for Owner’s attic stock.
E. Door Ventilation:
1. Louvered Ventilation, three-dimensional vertical vents formed on fronts and backs of door.
F. Latching:
1. Door containing stainless steel cup recessed into formed door. 2. 12 Ga steel finger lift mechanism. 3. Spring activated nylon slide latch enclosed in steel latch channel allows closing of door
while padlock or built-in lock is in position 4. Rubber bumpers riveted to door stops for silent operation 5. Locking device shall be completely recessed in door and be fingertip lift control and shall
include a built-in combination lock with master key.
G. Hinges:
1. 16 Ga continuous piano hinge on the right side of the opening. 2. Hinges welded to door and riveted to locker frame.
H. Solid Plastic Countertops:
1. Size: As indicated. 2. Solid Plastic - HDPE High Density Polyethylene with homogenous color and a matte
finish texture.
a. Color: As selected by Architect from manufacturer's full range. b. Length: as indicated.
I. Closed Base:
1. Provide 4 inch high, 14 Ga steel base enclosed on all four sides securely bolted or riveted to locker bottom.
J. Reinforced Bottom:
1. Provide 16 Ga spacer channel bolted or riveted to locker bottom from front to back Spacer channel to have full height 1/2-inch ID tube bolted or riveted over anchor holes to eliminate deflection upon locker installation.
K. Hooks:
1. Hooks to be heavy duty forged steel with ball ends and zinc plated. 2. Provide two single wall hooks and one double ceiling hook in each locker opening 20
inches or taller.
3. Numbering:
a. Furnish each locker with black anodized laser-etched aluminum number plate. b. Locate number plate near center of each door. c. Owner to furnish numbering sequence.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 P.E. LOCKERS 10 51 13 - 5
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
L. Finish: Units shall be thoroughly cleaned, given a bonding and rust inhibitive treatment, electrostatically sprayed with a heavy coat of high quality enamel on epoxy, then baked at 300-325 degrees F.
M. Provide fillers, trim, and necessary accessories.
N. Provide solid plastic end panels with minimum penetrations at exposed ends of locker rows and standard solid plastic end panels at unexposed locker ends and inside corners.
O. Opening mechanism for ADA accessible lockers shall be in strict accordance with ADA Accessibility requirements.
P. Tops and Ends Finishing Panels: Solid Plastic: Solid Plastic Materials: High Density Polyethylene (HDPE) containing a minimum of 10% recycled material which is waterproof, corrosion proof, impact resistant nonabsorbent, and has a self lubricating Poly-Glaze "280" surface that resists marking with pens, pencils, lipstick, and other writing or marking utensils.
1. Colors selected by the Architect from manufacturer’s standard colors.
2.4 LOCKER BENCHES
A. Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to the following:
1. ASI Storage Solutions; ASI Group. 2. Lyon Workspace Products, LLC. 3. Penco Products, Inc.
B. Provide bench units with overall assembly height of 17-1/2 inches.
C. Bench Tops: Manufacturer's standard one-piece units, with rounded corners and edges.
1. Size: Minimum 9-1/2 inches wide by 1-1/2 inches thick except provide minimum 20-inch- wide tops where accessible benches are indicated.
2. Solid Plastic - HDPE High Density Polyethylene with homogenous color and a matte finish texture.
a. Color: As selected by Architect from manufacturer's full range. b. Length: as indicated.
D. Fixed-Bench Pedestals: Manufacturer's standard supports, with predrilled fastener holes for attaching bench top and anchoring to floor, complete with fasteners and anchors, and as follows:
1. Tubular Steel: 1-1/2-inch- diameter steel tubing threaded on both ends, with standard pipe flange at top and base plate for casting into concrete slab; with baked-enamel or powder-coat finish.
a. Color: As selected by Architect from manufacturer's full range.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 P.E. LOCKERS 10 51 13 - 6
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine walls, floors, and support bases, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of the Work.
B. Prepare written report, endorsed by Installer, listing conditions detrimental to performance of the Work.
C. Proceed with installation only after unsatisfactory conditions have been corrected.
3.2 INSTALLATION
A. General: Install lockers level, plumb, and true; shim as required, using concealed shims.
1. Anchor locker runs at ends and at intervals recommended by manufacturer, but not more than 36 inches o.c. Using concealed fasteners, install anchors through backup reinforcing plates, channels, or blocking as required to prevent metal distortion.
2. Anchor single rows of metal lockers to walls near top of lockers and to floor. 3. Anchor back-to-back metal lockers to floor.
B. Knocked-Down Lockers: Assemble with manufacturer's standard fasteners, with no exposed fasteners on door faces or face frames.
B. Welded Construction: Factory preassemble metal lockers by welding all joints, seams, and connections; with no bolts, nuts, screws, or rivets used in assembly of main locker groups. Factory weld main locker groups into one-piece structures. Grind exposed welds smooth and flush.
C. Equipment:
1. Attach hooks with at least two fasteners. 2. Attach door locks on doors using security-type fasteners. 3. Identification Plates: Identify metal lockers with identification indicated on Drawings.
a. Attach plates to each locker door, near top, centered, with at least two aluminum rivets.
b. Attach plates to upper shelf of each open-front metal locker, centered, with a least two aluminum rivets.
D. Trim: Fit exposed connections of trim, fillers, and closures accurately together to form tight, hairline joints, with concealed fasteners and splice plates.
1. Attach recess trim to recessed metal lockers with concealed clips. 2. Attach filler panels with concealed fasteners. Locate filler panels where indicated on
Drawings. 3. Attach sloping-top units to metal lockers, with closures at exposed ends. 4. Attach boxed solid plastic end panels using concealed fasteners to conceal exposed
ends of nonrecessed metal lockers. 5. Attach finished solid plastic end panels using fasteners only at perimeter to conceal
exposed ends of nonrecessed metal lockers.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 P.E. LOCKERS 10 51 13 - 7
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
E. Fixed Benches: Provide no fewer than two pedestals for each bench, uniformly spaced not more than 72 inches apart. Bases shall be cast into concrete slab and protected, after other installation of adjacent materials is complete, fasten bench tops to bases and protect from damage.
3.3 ADJUSTING
A. Clean, lubricate, and adjust hardware. Adjust doors and latches to operate easily without binding. Verify that integral locking devices operate properly.
3.4 PROTECTION
A. Protect metal lockers from damage, abuse, dust, dirt, stain, or paint. Do not permit use during construction.
B. Touch up marred finishes, or replace metal lockers that cannot be restored to factory-finished appearance. Use only materials and procedures recommended or furnished by locker manufacturer.
END OF SECTION 10 51 13
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 P.E. LOCKERS 10 51 13 - 8
©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
THIS PAGE INTENTIONALLY LEFT BLANK
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 WALK-OFF ROLLED CARPET 12 48 13 - 1 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
SECTION 12 48 13 WALK-OFF ROLLED CARPET
PART 1 - GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply to this Section.
1.2 SUMMARY
A. Section Includes:
1. Walk-off Rolled Carpet.
1.3 SUBMITTALS
A. Product Data: For each type of product.
1. Include material descriptions and finishes for rolled carpet and edging.
B. Samples: For the following products, in manufacturer's standard sizes:
1. Rolled Carpet. 2. Carpet Edging.
1.4 CLOSEOUT SUBMITTALS
A. Maintenance Data: For rolled caprepts and edging to include in maintenance manuals.
PART 2 - PRODUCTS
2.1 ENTRANCE FLOOR MATS
A. Accessibility Standard: Comply with applicable provisions in the DOJ's "2010 ADA Standards for Accessible Design" and ICC A117.1.
2.2 RESILIENT ENTRANCE MATS
A. Basis-of-Design Product: Subject to compliance with requirements, provide Tandus Centiva, Assertive Stria #04839, powerbond cushion, or a comparable product by one of the following:
1. Babcock-Davis. 2. C/S Group. 3. JL Industries, Inc.; a division of the Activar Construction Products Group.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 WALK-OFF ROLLED CARPET 12 48 13 - 2 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
B. Rolled Carpet: Manufacturers carpet mix bonded to 1/8- to 1/4-inch-thick, flexible vinyl backing to form mats 3/8 or 7/16-inch thick with nonraveling edges.
1. Textures, and Patterns: As selected by Architect from full range of industry colors. 2. Color: As selected by Architect from Manufacturers full range. 3. Mat Size: 4’ X 6’. 4. Edging: Tapered flexible vinyl, not less than 1-1/2 inches wide, attached to mat at all four
edges, with bonded mitered corners.
a. Vinyl Color: As selected by Architect from full range of industry colors.
2.3 FABRICATION
A. Rolled Carpet: Shop fabricate units to greatest extent possible in sizes indicated. Unless otherwise indicated, provide single unit for each mat installation; do not exceed manufacturer's recommended maximum sizes for units that are removed for maintenance and cleaning.
2.4 MISCELLANEOUS ACCESSORIES
A. Metal Edge Strips: Angle or L-shaped, height to match tile and setting-bed thickness, metallic or combination of metal and PVC or neoprene base, designed specifically for flooring applications.
1. Basis of Design Product and Manufacturer; Tandus Centiva, MetalEdge Trois #ME003, or, available manufacturers offering products that may be incorporated into the Work include, but are not limited to the following:
a. Blanke Corporation. b. Ceramic Tool Company, Inc. c. Schluter Systems L.P.
2. Material and Finish: As selected by the Architect from the Manufacturers full range.
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine substrates and floor conditions for compliance with requirements for location, sizes, and other conditions affecting installation of floor mats.
B. Proceed with installation only after unsatisfactory conditions have been corrected.
3.2 INSTALLATION
A. Install surface-type units to comply with manufacturer's written instructions; coordinate with entrance locations and traffic patterns.
END OF SECTION 12 48 13
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 1 ADDENDUM - 01 - 08/20/18
SECTION 23 09 23 INSTRUMENTATION AND CONTROL DEVICES FOR HVAC
PART 1 - GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and SupplementaryConditions and Division 01 Specification Sections, apply to this Section.
B. The following specifications are also related to this section:
1. Specification Section 23 05 93 - Testing, Adjusting and Balancing for HVAC Systems.2. Specification Section 23 08 00 – Commissioning of HVAC System requirements.3. Section 23 33 00 - Air Duct Accessories4. Section 23 36 00 – Air Terminal Units.5. Division 26 - Electrical
1.2 WORK INCLUDED
A. Control system to be installed on an existing campus. System shall be a stand-alone systemintegrated with the existing campus system.
B. Complete stand alone, open protocol Direct Digital Control (DDC) (BACnet) Building ControlSystem (BCS) including all control devices, valves and dampers except where furnished underother sections.
C. The DDC system shall have a BACnet Testing Labs (BTL) approval. The devices that shall beapproved include, but are not limited to, the operator Interface (frontend) software, primarynetwork supervisor and equipment control panels.
D. Interface with Product Integrated Controls specified in other sections of the specifications.
E. Chiller Control Panel Interface: Provide all necessary programming and setup to provide directcommunication to chiller manufacturer’s BACnet translator software to provide the chillercommands, points, and diagnostic messages as specified in the points list and sequence ofoperations. The contractor will coordinate all requirements with the various chiller manufacturersprior to bid and include all costs necessary to provide the chiller data through the BAS networkincluding to the Owner’s remote operator computer.
F. This section also includes Web Based Open Protocol DDC building network controllers andEquipment controllers that are open protocol utilizing BACnet protocol for the purpose ofcontrolling HVAC systems and components, including control components for terminal heatingand cooling units not supplied with factory wired controls, lighting in new and existing facilities.
G. Provide and install 2 copies of all necessary software and programs on 2 different devices (alaptop computer, and the District server) for the Owner. Contractor to coordinate with the Ownerto install this software on the offsite server, and the other computer shall be the service laptopdescribed under this specification.
H. Access to the controls shall be through an owner provided IP address with use of a user.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 2 ADDENDUM - 01 - 08/20/18
I. ID and password. Contractor to provide multi-user web server software as part of the contract forthe District server, District PC and the laptop computer.
1.3 QUALITY ASSURANCE
A. The installation of the building control system shall be by the manufacturer of the controls or hislocal authorized agent who has a minimum of five (5) years of representation in this County.
B. All electrical components 25 V and above shall be U.L. listed or labeled.
C. All equipment or piping used in the conditioned air stream, spaces or return air plenums shallcomply with NFPA 90A Flame/Smoke/Fuel contribution rating of 25/50/0 and all applicable localbuilding codes or requirements.
D. All wiring shall conform to the National Electrical Code (NEC).
E. All smoke dampers shall be rated in accordance with UL 555S.
1.4 DEFINITIONS
A. Control Wiring: All wiring, 120 VAC or low voltage other than power wiring, required for the properoperation of the mechanical system.
B. Power Wiring: All line voltage wiring to the mechanical equipment. Note: Where line voltageserves a control circuit such as power to a transformer, power to a DDC control panel, power for aline voltage thermostat, or damper this shall be considered control wiring.
1.5 SUBMITTALS
A. Submit in accordance with Division 01 Requirements.
B. Provide complete catalog data and installation instructions for each control component. Includedamper and valve sizing details.
C. Control system submittal shall contain the following graphics and documentation for each systembeing controlled:
1. Communications bus schematic showing all panel locations and hardware requirements.2. Schematic wiring diagrams in ladder form for each system including power source.3. Schematic diagram with detail of all hardware, components used, location of instruments,
bulbs, dampers, valves and other components. The chart shall include control chartincluding control symbols, quantity, manufacturer's part number, tech sheet reference(include in submittal) and description of part.
4. Each DDC field panel shall be detailed in the submittal to identify termination boards withineach panel and terminal of their respective field points. Each termination point shall definethe point name and point description by each terminal with the field panel. Point namesand descriptors shall be consistent throughout the submittal on the schematics, wiringdiagrams, equipment list, etc.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 3 ADDENDUM - 01 - 08/20/18
5. Submit the system architecture or configuration complete with all processors, terminals,other peripheral devices, modems, etc., with interconnecting diagrams.
6. A report shall be included in the submittal to include every point in the entire system.The report shall include the programmed data for each point:
a. Point Nameb. Point Type (analog, digital, etc.)c. Point Descriptord. Physical Address (enclose legend)e. Alarm (yes or no)f. Print Alarm (yes or no)g. High Limith. Low Limiti. Totalized (yes or no)j. Hours or Minutes Totalizedk. Engineering Unit of Point
7. A flow chart form of sequence of operation in abbreviated English language.8. English language sequence of operation defining flow chart with control company
programmed inputs to reflect English language sequence. Each sequence task shall befollowed by the control company coded program. One list of coded programmed inputsat the end of each sequence of operation shall be acceptable.
D. For each Direct Digital Control (DDC) panel provide:
1. Point List identifying each input and output by point name, point type, hardwaredescription, wiring terminations, mounting arrangements and software features.
2. Complete English language description of all software.3. Flow diagram and complete details program.
1.6 CONTROL SYSTEM GENERAL REQUIREMENTS
A. The control system shall be of the electronic microprocessor type employing Direct DigitalControl (DDC) Open Protocol (BACnet) technology for all control sequences unless specificallystated otherwise in the Sequences of Operation as indicated on the contract documents.
B. All DDC controllers shall be connected via a communications bus to the operator’s laptop. Inaddition, a portable operator’s laptop shall be capable of connecting to the system at any DDCcontroller location.
C. All DDC controllers shall be connected to a global information handler, which shall send andreceive information of a global nature throughout the system. The information handler shallallow each DDC controller and operators panel access to all information contained within thesystem, regardless of location. The information handler shall also allow commands from anyDDC controller or operators panel to be directed to any other DDC controller on either a globalor individual basis. The information handler may be furnished as an integral part of one or moreDDC controllers. This “Building Network Controller” shall be an Open protocol controller thatwill allow the simultaneous communication to BACnet communication residing on the lower tiercontrollers (equipment controllers). The building controller shall be capable to be accessedusing the majority of internet open protocols such as JAVA, XML, HTTP, Etc.
D. Provisions shall be made to allow additional DDC controllers to be added at any point on thecommunications bus for future expansion.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 4 ADDENDUM - 01 - 08/20/18
E. Field Installed Devices (FID), shall be capable of stand-alone operation, as well as interfacing withthe networked Building Control System. These controllers shall be BACnet Protocols. No otherprotocols for this section will be acceptable.
F. Valve and damper operators shall be of the electronic type.
G. The Building Control System shall be made up of HVAC equipment with factory installedmicroprocessor-based Product Integrated Controls (PIC), distributed microprocessor- based FieldInstalled Devices (FID), input/output modules and necessary software.
H. The Product Integrated Controls (PIC) shall be factory installed controls capable of stand- aloneoperation. The controller shall be specifically designed to operate and monitor the functions of theHVAC equipment on which it is installed. The PIC shall be capable of interfacing onto the network.
I. The Building Network Controller shall incorporate the GUI (Graphical User Interface) via astandard web browser. Use of hardware keys or special licensing requirements to access thesystem with a web browser is unacceptable. The Building controller shall be capable ofstandalone operation should the WAN connectivity to the central server fail for any reason. If theWAN is not working, an operator shall be able to access the system on site via the supplied tech-tool laptop in order to monitor operations and adjust settings as necessary. Loss of WANconnectivity shall generate alarms at both the central server and the local building controller untilWAN connectivity is restored. The central server computer will be located at the energymanagement office to supervise the remote panels and alarm if communications is lost as well asany control alarm function. This central server computer will also archive trended data from thesite. Refer to that requirement within this specification section.
1.7 INTENT OF DRAWINGS AND SPECIFICATIONS
A. The implied and stated intent of the drawings and specifications is to establish minimumacceptable quality standards for materials, equipment and workmanship and to provide acomplete and operable building control system.
B. The drawings are diagrammatic intending to show a workable general arrangement and locationof system components and are not necessarily complete or rigid in all details.
C. Deviation in the detailed building control system due to the inherent differences in alternatecontrol systems will be allowed provided the intent and minimum quality standards detailed andspecified are maintained.
D. No deviation in the specified sequence of operation will be allowed without written approval fromthe Engineer.
1.8 OPERATION AND MAINTENANCE MANUALS AND INSTRUCTIONS FOR OWNER
A. Operation and maintenance manuals shall be provided as outlined in Division 01 Requirements.The manuals shall include all data which was a part of the original submittal with as- built wiringdiagrams, parts lists and operating and maintenance instruction manuals.
B. A total of 40 hours of on the job owner training conducted by a technician or technicians fullyqualified to conduct such training shall be provided. Instruction or Training shall include, but notbe limited to:
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 5 ADDENDUM - 01 - 08/20/18
1. Instructions in the manufacturers recommended maintenance and operatingprocedures.
2. Instructions in the detailed sequence of operation of the mechanical equipment controls.3. Instructions in reading and using the control wiring diagrams.4. Instructions in control setpoint adjustment as relating to each specific system provided
under this section.5. Performance testing as described in Part 3.
1.9 COOPERATION WITH OTHER CONTRACTORS
A. The Building Control Sub-Contractor shall coordinate with other trades to assure a completeand operational Building Control System.
B. This contractor shall furnish to the air balance contractor (Section 23 05 93) a laptop PCcomputer for terminal box set-up (per section 2.2-C below). At the completion of the balancing,the laptop PC computer shall be turned over to the owner.
1.10 MATERIALS, STORAGE AND HANDLING
A. All components shipped to the job-site and stored on-site shall be stored in a clean, dry storagelocation.
1.11 TRAINING
A. Provide 40 hours, on-site, of a factory-authorized representative to train the Owner’smaintenance personnel to adjust, operate and program the DDC System. Provide any requiredtraining requested by the Owner during this 40 hour period.
PART 2 - PRODUCTS
2.1 ACCEPTABLE MANUFACTURERS/REPRESENTATIVES
A. Manufacturers:
1. Certified Controls – Automated Logic
2.2 EQUIPMENT
A. Direct Digital Control (DDC) Controllers:
1. Direct Digital Control (DDC) Controllers shall be field programmable microprocessorbased, electronic controllers incorporating direct digital control technology. The DDCcontrollers shall be capable of performing their assigned control and energymanagement functions as standalone units or as part of a comprehensive BuildingManagement System. The controllers shall be capable of performing energymanagement functions including, but not limited to supply air and water reset,economizer, duty cycling, chiller optimization, morning cool-down and warm-up, solarcompensation, unoccupied setback, and real-time scheduling.
2. The controllers shall have built-in, non-volatile, real-time calendar clocks capable ofgenerating real and elapsed time signals in years, months, days of the week, hours,minutes and seconds, as well as elapsed time in days, hours, minutes and seconds.The controller shall be provided with a minimum of 72 hour back-up capability protectagainst loss of time in the calendar clock and the programmed software and providesurge protection on the head end terminal.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 6 ADDENDUM - 01 - 08/20/18
3. The controllers shall be capable of interfacing with a standard twisted paircommunication channel for local operation and shall be protected with software securitycode keys to prevent unauthorized access. Where practical, controllers shall be fullydistributed and dedicated to an individual piece of equipment or system. Wheninput/output requirements exceed the capacity of a controller, additional controllers shallbe connected serially in a daisy chain configuration to allow for the use of a singleRS485 interface channel for multiple controllers. Global level controllers shall allow fullInternet Protocol (IP) communications through a static IP connection through a 10/100megabit per second Ethernet protocol.
4. The controllers shall be programmed for the sequences of operation defined hereinafter.The execution of these sequences shall be fully automatic and without operatorintervention. The controllers shall sense all of their inputs, test for multiple inputprogrammed conditions and execute appropriate action on valves, dampers, pumps,fans and other equipment. The programmed conditions may include any combination ofinputs, outputs, time and the mathematical operations (addition, subtraction, greaterthan, less than, square root, or absolute value). Program changes shall be entered intothe controllers without interruption of the system operation.
5. The controllers shall be completely field programmable from a standard portableprogramming unit, a CRT terminal or from a remote location through authorized VPNaccess. The program logic shall allow changes without interruption of the systemoperation.
6. The controllers shall be programmed to examine their inputs for emergency conditionsand to automatically initiating the actuation of the appropriate alarm mode.
7. The operator, through a terminal, shall be capable of overriding the programmed controlsequence to manually operate the outputs for system checkout. All sequences ofoperation shall be demonstrated through this simulation technique. The controllers shallbe stepped through their sequence to verify system operation. During the maintenanceroutine, the controllers shall be capable of selectively disabling inputs and outputswithout affecting the operations of the remaining inputs and outputs. The controller’sstatus shall be accessible through the ASCII channel. Upon appropriate commands, thecontroller shall read out time, analog input values, output status, program line numberbeing processed, disabled inputs, disabled outputs and sequencing program logic.Through the ASCII channel, the controllers shall be capable of printing a data history logfor maintenance and troubleshooting of the system.
8. The controllers shall have a minimum of four levels of access available for terminaloperation of the unit. The number of functions allowed an operator shall be determinedby the level of password that is correctly entered into the controller.
9. The executive operating system provided with the controllers shall provide for all thefunctions described herein. The executive system shall provide English error messagesto the user when any command or date is entered that cannot be understood by themicroprocessor. An editing system shall also be provided for program entry. A programand variable trace routine shall also be provided to allow for easier program testing anddebugging.
10. Digital Controllers used to control terminal equipment, such as variable volume boxes,shall be designed as individual control units. All variables shall be capable of beingviewed and changed from the operator’s laptop.
11. Digital Controllers used to control variable air volume (VAV) shall include:
a. Pressure independent air volume controller capable of controlling air volumewithin 5% of design air volume from minimum to maximum flow and at all pointsin between regardless of changes in system static pressure. Air volumemaximum and minimum to be factory set and field readjustable. Controller shall becapable of 3 set positions: Off, Minimum and Maximum with VAV control from themin. to max. position. Minimum air volume shall be accurately controlled as low as100 FPM based on inlet duct size. Maximum and minimum air volumes as
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 7 ADDENDUM - 01 - 08/20/18
scheduled on the drawings. If special multi-point velocity sensor is required to meet the specification, this supplier to furnish and coordinate installation with terminal supplier.
b. 24 VAC damper actuator. NC control operation as specified.c. Digital output for fan control.d. Digital outputs for each step of electric heat control.e. Temperature sensor.f. A factory calibrated damper assembly and multi-point velocity sensor is specified
to be provided with VAV terminals under Section 23 36 00 – Air Terminal Units.Provide 24V power source and wiring to terminal controller on VAV units which donot have a fan under this division, and in addition, a 24V, 40VA controltransformer will be supplied on fan powered units by the terminal manufacturer.This supplier shall coordinate all requirements with the terminal supplier.
B. Operators Communications
1. Communication with school BAS shall be possible via an Owner provided IP addressand use of a User ID and password from any District computer. Software installation toaccess controls is not acceptable. All manufacturers must provide multi-user webserver software on both the District server, and the laptop described below.
2. Central Site: The contractor shall provide a central site system configuration thatincludes, as a minimum, the following components: Placement of computer to bedetermined by SJCSD Energy Management Department.
a. Laptop Computer: The computer shall be Intel® Coretm i7-6500U processor witha minimum CPU speed of 2.5 GHz with 1 terabyte (TB) HDD hard drive, 16gigabyte (GB) memory (minimum 1600 MHz speed) and minimum 15.6” screen.
b. Provide Wi-Fi capability matching Wi-Fi standard 802.11ac.c. Provide Windows® 10 Pro operating system.d. Provide a Wi-Fi capable inkjet printer.e. Controls contractor to verify these requirements meet the minimum requirements
of the software required to be uploaded to the laptop. Controls Contractor to fullload all software and have computer fully set- up prior to issuing to the Owner.The controls vendor is responsible for the condition of the laptop after use by thetest and balance vendor.
C. Input-Output Devices:
1. Temperature Sensors:
a. Temperature sensors shall be provided for space, duct, fluid, and outside airsensing which are compatible with the digital controllers. All temperature sensorsshall be accurate to .36°F over a range of -30 to 220°F and shall have ademonstrated stability of .04°F over a 10 year period.
b. Temperature sensors shall be 10K resistor style.c. All sensors in water lines to be installed in wells. If a permanent thermometer is
not located at sensing point, a second well will be installed adjacent fortemperature verification purposes.
d. All sensors for cooling or heating coil leaving air temperatures shall be serpentinetype across entire coil surface area. Sensing tube type is not acceptable.
e. Room temperature sensors in public spaces (Auditoriums and Gymnasiums) shallhave concealed setpoint adjustment with blank covers.
f. Room temperature sensors in private offices and classrooms shall have useraccessible setpoint adjustment with setpoint indication and space temperatureindication with adjustable minimum and maximum setpoints capability with digital
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 8 ADDENDUM - 01 - 08/20/18
read outs.
2. Humidity Sensors:
a. Electronic Humidity Transmitters: Electronic humidity transmitters shall produce alinear 4-20 ma signal over a range of 0 to 100% RH. Accuracy shall be ±2% of fullscale.
b. Single point calibration.c. Shall be either VAISALA HMD-60U for duct applications and VAISALA HMW-60U
for wall mounted applications or Veris.d. Room Humidity sensors shall be integral to the room temperature sensor so that
there is only one sensor per room.
3. Pressure Sensors:
a. Electronic static and differential pressure transmitters shall be stainless steeldiaphragm type, with a variable capacitance electrode to produce a linear signalover the appropriate input range. Input ranges shall be available from 0.1 in. H2 Oto 7.5 in.H2 O and transmitters shall be selected for 150% of the design pressure.
ull scaleover the selected range, wherever differential pressure transmitters are subject todamage by disconnecting pressure lines, provide three valve manifolds fordisconnection and testing. Based on Delta-Pro
4. Valves and Operators:
a. Isolation Type Valves:
1) 2" and smaller: Ball style, sized for minimum pressure drop.2) 2-1/2" and larger: Butterfly style, sized for minimum pressure drop.
b. Control Valves:
1) Valves shall be provided with equal percentage modulating plugs,renewable composition disk especially compounded for hot or coldwater service to assure tight seating. Three-way valves shall befurnished with modulating type plug assemblies and shall have oneseat machined integral with the body and the other three-way valveend.
2) Valves shall be sized as indicated or as required to guaranteesufficient size to meet the heating or cooling requirements withspecified pressure drops. Water valves shall be sized for 2 psigminimum and 5 psig maximum pressure drop. Valves 2 inches andsmaller shall be screwed and valves 2-1/2 inches and larger shall beflanged.
c. Valve operators:
1) Shall be gear driven electronic. Operators shall be of sufficient sizeto ensure smooth positive, operation and tight shut-off againstsystem pressure.
2) Electronic operators shall be of the positive gear driven type using abrushless DC motor with built-in mechanical stops and electroniccurrent limiting circuit to prevent burn-out. The drive motor shall bemicroprocessor controlled and capable of accepting a 4-20 mA, 0-10 V DC, 0-20 V Dc phasecut, on-off, or floating tri-state control
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 9 ADDENDUM - 01 - 08/20/18
signal as required. Based on Belimo Aircontrols (USA), Inc. 3) Preheat coil valves and valves on the primary and secondary
heating water circuits shall have spring returns. The water valvesshall be designed to go to the open position on power or otherfailure.
4) The source of power for valve operation, electronic shall be theresponsibility of the BCS Contractor.
5. Butterfly Valves and Operators:
a. Isolation valves and control valves 4" and over may be butterfly type.b. Valves to have 416 stainless steel stem, full lug, cast iron or ductile iron body to
permit removal of downstream piping, long neck body extended to allow for aminimum of 2" insulation, aluminum bronze or stainless steel disc, bubble tightEPDM seat, infinite position throttling, Class 150, 20°F to 220°F range.
c. Where three way valves are shown, factory furnished T-assemblies with mountedvalves and cross linkage may be used.
d. Valves to have gear driven electronic operators. Operators to be of sufficient sizeto ensure smooth, positive operation and tight shut-off against system pressure.Preheat coil valves and valves on the primary and secondary heating watercircuits shall have spring returns. The water valves shall be designed to go to theopen position on power or other failure.
1) Shall be gear driven electronic. Operators shall be of sufficient sizeto ensure smooth positive, operation and tight shut-off againstsystem pressure.
2) Electronic operators shall be of the positive gear driven type using abrushless DC motor with built-in mechanical stops and electroniccurrent limiting circuit to prevent burn-out. The drive motor shall bemicroprocessor controlled and capable of accepting a 4-20 mA, 0-10 V DC, 0-20 V Dc phasecut, on-off, or floating tri-state controlsignal as required. Based on Belimo Aircontrols (USA), Inc.
3) Preheat coil valves and valves on the primary and secondaryheating water circuits shall have spring returns. The water valvesshall be designed to go to the open position on power or otherfailure.
4) The source of power for valve operation, electronic shall be theresponsibility of the BCS Contractor.
i. The source of power for valve operation, electronic shall be theresponsibility of the BCS Contractor.
ii. Based on Keystone Fig. AR2.
6. Dampers and Operators:
a. Outside, return, relief and exhaust air dampers shall be low leakage proportion/airtype, and shall have a leakage of less than 1/2% when closing against 4 in. w.g.static pressure. The frame shall be 16 gauge galvanized steel hat shaped channelwith corner braces. Blades shall be constructed of 16 gauge galvanized steel on 6inch centers. Blade seals shall be EPDM and jamb seals shall be flexible metal,compression type. Fan discharge dampers and return air dampers are to be usedas smoke dampers and shall be minimum Class II rated as smoke dampers perUL 555S. Air handling unit maximum outside and relief air dampers shall beopposed blade type. Return air damper shall be parallel blade type positioned to
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 10 ADDENDUM - 01 - 08/20/18
direct return air toward the O.A. damper. Each damper shall have an individual actuator and analog output. Where a minimum O.A. damper is indicated, it shall have a separate digital output.
b. Electronic operators shall be of the positive gear driven type using a brushless DCmotor with built-in mechanical stops and electronic current limiting circuit toprevent burn-out. The drive motor shall be microprocessor controlled and capableof accepting a 4-20 mA, 0-10 V DC, 0-20 V DC phasecut, on-off, or floating tri-state control signal as required. Based on Belimo Air Controls (USA), Inc.
c. Actuators for outdoor air and exhaust air dampers shall have spring return, andthe dampers shall be designed to go to the closed position on power or otherfailure.
7. Smoke Detectors:
a. Smoke detectors (SD) will be furnished and installed by Division 26 – Electricaland Division 23 – Mechanical. (Refer to Specification Section 23 33 00). Detectorswill be required in all air handling systems greater than 2000 CFM. Detectors willbe required in both supply and return ducts of air handling units or on multi-storybuildings in the return at each floor. The detectors shall be wired to shut-down thefans and indicate status to the DDC controls. In the case of an engineered smokecontrol system, they shall be wired to control as specified and shall be interlockedwith the fire alarm system.
8. High limit thermostats (FS) shall be provided for each exhaust fan and shall be of themanual reset type. Thermostats shall be UL listed and shall be wired to shut down theirrespective fans should the temperature in the duct rise above 125°F (adj.).
9. Low limit thermostats (FR) shall be provided as indicated and shall be wired to shutdown their respective unit should the temperature at any point on its sensing elementfall below 35°F (adj.). Thermostats shall require manual reset. Provide 1 foot of sensingelement for each 2 sq. ft. of duct cross section.
10. Panels:
a. All relays and similar devices shall be mounted within Control Panels. Quantityand location of control panels shall be dictated by the controls contractor’s systemarchitecture.
b. Control panels shall be dust tight and furnished with hinged locking doors. Providean engraved nameplate on the face of the panel clearly describing its function. Alldevices located within the panel shall be clearly labeled. All wiring within the panelshall be in accordance with NEMA, UL standard, NEC and local codes. Detailsand proposed mounting location of each panel shall be submitted prior toconstruction. All panels shall be factory prewired and pre-piped to terminal stripsprior to arrival at job site. The wiring shall be installed orderly and easilyidentifiable.
c. Provide wiring diagram mounted inside door with plastic protective covering.
11. Relays:
a. All relays shall be plugged in, interchangeable, mounted on a circuit board andwired to numbered terminal strips.
b. Start/stop relay modules shall provide either momentary or maintained switchingaction as appropriate for the motor being started.
12. Differential Pressure Switches: Binary differential pressure sensors shall be used toindicate pump and fan operation and for indicating high pressure drop across filters.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 11 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
These sensors shall be of the diaphragm type and shall be adjustable and furnished in ranges compatible with their service.
13. Current Sensing Relays:
a. Solid state switch which operates when current level sensed by internal currenttransformer exceeds the threshold value set by the adjusting device. Internalcircuits totally powered by induction from line being monitored.
b. Current range and switching characteristics as required for intended duty.
14. Line Voltage Electric Thermostats:
a. Where mechanical equipment such as certain exhaust fans or unit heaters areindicated to be controlled directly from a space thermostat, provide a thermostat ofeither the heating or cooling type depending upon the application.
b. All line voltage thermostats shall be rated to carry 125% of the load of thecontrolled device.
15. Thermostat/Temperature Sensor Guard:
a. Wire guard with steel base.b. Cast aluminum guard with steel base.c. Clear plastic guard with solid base and tumbler type key lock.d. Contractor to verify the location of these guards with engineer and Owners
representative.
16. Water Flow Meters:
a. Flow meters shall be insertion electromagnetic type, suitable for hot tap insertionand removal as required. The meter shall mount on a 1 inch full opening isolationvalve. The meter assembly shall consist of all necessary interface electronics totransmit a compatible digital pulse train flow signal to the digital system controller.
b. Wiring installed by the contractor between the control system and thetransducer shall be Belden 9320, two wire, shielded twisted cable, and shall notbe included in conduit containing AC circuit wiring.
c. The flow transducer shall utilize an electromagnetic sensing flow meter with nomoving parts. The flow transducer shall have an achievable accuracy of +/-1% offlow rate with flow velocities of 2 to 20 fps when installed with 10 pipe diameters ofstraight pipe before the transducer and 5 pipe diameters after the transducer.Provide 36” clear from pipe to top of meter.
d. The meter shall provide a single analog output for flow rate, a high resolutionfrequency output to drive peripheral devices, a scalable pulse output fortotalization and an empty pipe alarm signal.
e. The system shall include a System-10 BTU meter for energy management andshall be mounted next to the BCS panel in the central energy plant.
f. Based on Onicon electromagnetic flow meter Model F-3500 (No Substitutions)
17. Air Flow Measuring Station: Duct and plenum mounted airflow measurement devices.
a. The following is the only acceptable manufacturer:
1) EBTRON, Inc. Model GTx116-P (basis of design, no substitutions),HTx-104-P (when meeting sensor densities).
b. Alternatives requesting acceptance as “equals” less than 60 days prior to bid dateor products submitted in non-conformance with the requirements of this
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 12 ADDENDUM - 01 - 08/20/18
specification will not be considered. c. For any product to be considered for substitution a written section-by- section
detailed exceptions/compliance document shall be submitted to the Engineerbefore any approval will be considered.
d. Any product offered as an equal to EBTRON shall make a working demo availablefor a side by side evaluation in the specifying engineer’s office.
e. The working demo must be able to demonstrate airflow measurement throughoutthe entire specified range (50 - 5000 FPM), repeatability, and response time andspecification compliance. Providing a working demo in and of itself does notconstitute its approval.
f. Provide airflow/temperature measurement devices (ATMD) where indicated on theplans or as recommended by an authorized EBTRON representative Fan inletmeasurement devices shall not be used unless specifically indicated on the plans.
g. Each ATMD shall consist of one or more sensor probes and a single, remotelymounted, microprocessor-based transmitter capable of independently processingup to 16 independently wired sensor assemblies.
1) Each sensor node shall contain two individually wired, hermeticallysealed bead-in-glass thermistors.
2) Thermistors shall be mounted in the sensor node using a marine-grade, waterproof epoxy. Thermistor leads shall be protected andnot exposed to the environment. Thermistor leads shall not befastened to the thermistor semiconductor substrate by weld orsolder connections.
3) The airflow rate of each sensor assembly shall be equally weightedand averaged by the transmitter prior to output. All integratedcircuitry shall be temperature rated as ‘industrial- grade’.Submissions containing ‘commercial-grade’ integrated circuitry arenot acceptable.
4) The temperature of each sensor assembly shall be velocityweighted and averaged by the transmitter prior to output.
5) Each transmitter shall have a 16-character alpha-numeric displaycapable of displaying airflow, temperature, system status,configuration settings and diagnostics.
6) Devices using chip-in-glass or diode-case chip thermistors are notacceptable.
7) Devices using less than two thermistors in each sensor assemblyare not acceptable.
8) Devices having electronic circuitry mounted in or at the sensorprobe are not acceptable.
9) Pitot tubes and arrays are not acceptable.10) Vortex shedding devices are not acceptable.11) Duct and Plenum Probes
i. Probes shall be constructed of extruded, gold anodized, 6063aluminum tubes or optionally of Type 316 stainless steel tubes.All internal wires within the tube shall be Kynar coated. PVCinsulated conductors are not acceptable.
ii. The number of individual sensor nodes provided for eachlocation shall be as follows:
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 13 ADDENDUM - 01 - 08/20/18
Duct or Plenum Area (ft2) Total # Nodes / Location Duct or Plenum Area (m2)
<= 1 1 or 2 <= 0.093
>1 to <2 4 >0.093 to < 0.372
2 to < 4 6 0.372 to < 0.743
4 to < 8 8 0.743 to < 1.115
8 to <16 12 1.115 to < 1.486
>=16 16 >= 1.486
iii. Sensor probe design shall be capable of providing up to 8sensor nodes per probe.
iv. The minimum operating airflow range shall be 0 to 5,000 FPM(25.4 m/s) unless otherwise indicated on the plans.
v. Each ducted sensor probe shall have an integral, U.L. Listed,plenum rated cable. Cable jackets and conductor insulation shallbe FEP, Teflon-FEP or Neoflon-FEP. Cables shall include aterminal plug for connection to the remotely mounted transmitter.All terminal plug interconnecting pins shall be gold plated. PVCjacketed cables or PVC insulated conductors are not acceptablewith ducted sensor probes.
18. Control Air Tubing:
a. Copper hard drawn or annealed.b. Fittings copper or brass, sweat or flare compression type.c. Non-metallic FR Polytubing. Tubing shall be suitable for use in return air plenums.
19. Domestic Water Recirculation Pumps:
a. Provide a software interlock for control, scheduling and monitoring of all domesticwater pumps.
20. Domestic Water Drinking Fountains:
a. Provide a software interlock for scheduling of all domestic water drinkingfountains.
21. KW Meter:
a. Provided on the following equipment/locations by the BCS manufacturercoordinated with the electrical contractor):
1) All chillers and pumps. If the main service for the entire plant cannotbe monitored through one point of electrical service the KWconsumption shall be totaled for all equipment within the CEP andrecorded through the BCS.
2) Main service to the Building. The KW shall be monitored at the mainMDP for the building.
b. Product description shall include the following:
1) Surface mounted within the pump house.2) Provide BACnet output.3) Provide data logging capability for protection of data in the event of
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 14 ADDENDUM - 01 - 08/20/18
a power failure. 4) Provide combinations of serial communication, pulse output, and
phase alarms.5) Provide pulse inputs to incorporate simple flow sensors to track gas,
water, steam, or other energy forms using a BACnet system.
c. The Features shall include the following:
1) Revenue Grade measurements2) Wall mounted3) ANSI 12.20 0.5% accuracy, IEC 62053-22 Class 0.5S4) Real energy output and phase loss alarm output5) 90-600VAC6) Data logging capability7) Compatible with CTs from 5A to 32000A8) User-enabled password protection (E5xHx)9) BACnet MS/TP support (no gateway) with serial rates up to
115.2 kbaud (E5xHx)10) Bi-directional metering (4-quadrant), an essential solution for solar
and other renewable energy applications, measures Import, Exportand net energy transfer
11) CSI approved
d. The accessories shall include the following:
1) NEMA4 enclosure and locking mechanism, required if mountedoutdoors
2) Fuse Kits with hi-interrupt capability AC Fuses3) Split-core and solid-core CTs4) Replacement mounting clips5) BACnet IP Router
e. Based on Veris Industries Model E5x Series
22. Smoke dampers shall be as specified in Section 23 33 00 – Air Duct Accessories.
2.3 SYSTEM SOFTWARE
A. General:
1. The Contractor shall provide all software required for efficient operation of all functionsrequired by this specification. Software shall be modular in design for flexibility inexpansion or revision of the system. The software shall, as a minimum, include:
a. Complete database entryb. Configuration of all application programs to provide the sequence of operation
indicatedc. Complete graphics package, including graphics floor plans and individual
graphics, for each system.d. Alarm limits and alarm messages for all critical and non-critical alarmse. Configuration of all reports and point summaries indicated
2. The system software shall be complete such that each control loop shall function asspecified in the Sequence of Operation.
3. The building control system manufacturer shall be required to write the softwareprogram and test the operation of every control loop. A letter certifying that the system
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 15 ADDENDUM - 01 - 08/20/18
is ready for inspection shall be submitted to the engineer prior to the controllers being shipped to the field. The engineer may at his option visit the contractor's office and witness proper operation of each control loop prior to shipping from the contractor's point of fabrication. The control contractor shall provide a means of simulating every input to the system as a requirement for debugging the software. Prior to shipping of the microprocessor controller, the debugged software shall be transmitted to the owner for approval.
4. After all field connections have been made and control power is available in the controlpanel, the owner shall be notified and the control system shall be energized. Anyrequired reloading of the software shall be performed and start-up of the mechanicalsystem and building control system shall commence.
5. The building control contractor shall be responsible for all necessary revisions to thesoftware as required to provide a complete and workable system consistent with theletter and intent of the specification. All performance criteria for sequencing of systemas indicated in the control diagrams as indicated in the contract documents shall befollowed.
6. After the system has operated properly for 90 days following start-up of the finalcomponent of the heating and air conditioning systems, an as-built copy of the softwareshall be transmitted to the owner for permanent record purposes. Any softwareupgrading or enhancements to improve the system operation or as required for properoperation of the system during the first year of operation is the responsibility of thebuilding control system contractor. Any changes to the software shall be immediatelytransmitted to the owner.
7. The software required to provide the initial operation routines shall not consume morethan 70% of the programmable capability of the controller.
8. The software shall be provided in these five categories:
a. System executive softwareb. Software for user control over system configuration at the Central Site location,
and by Maintenance Personnel in the fieldc. Facility monitoring functionsd. Direct digital controle. Application software
9. Each category of software shall consist of interactive software modules. Each moduleshall have an associated priority level and shall execute as determined by the programcontroller as defined in the real time operating system.
10. The building operator shall be able to communicate and direct all control functionsthrough the use of a 2-button "mouse" operator interface to monitor and control allfunctions and sequences within the system.
11. The central site shall allow receipt of alarms and messages while in a functional modeother than energy management. i.e. incoming alarms shall be displayed while theoperator is in a word processing, spreadsheet or other operating mode. The systemmust automatically switch from a non- energy management mode, respond to an alarm,and return to the exact position left in the previous functional mode.
12. The central site must be able to generate standard ASCII file formats to allow use withthird-party software (Microsoft Excel) to generate and store owner-designed reports.
B. Systems Software:
1. The central site shall display graphically, in up to 64 different colors, the followingsystem information:
a. Floor plan maps shall show heating and cooling zones throughout the buildings ina range of colors which provide a visual display of temperature relative to their
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 16 ADDENDUM - 01 - 08/20/18
respective setpoints. The colors shall be updated dynamically as zones' comfort condition change. Locations of space sensors shall also be shown for each zone. Setpoint adjustment and color band displays shall be provided as specified.
b. Lighting floor plan maps shall show the status of each individual lighting circuit.When the lights are "on", the area served shall respond in a pre-selected color.When the lights are "off", the area served shall appear gray.
c. Mechanical system graphics shall show the type of mechanical systemcomponents serving any zone through the use of a pictorial representation ofcomponents. It shall also provide a current status of all I/O points being controlledand applicable to each piece of equipment including analog readouts inappropriate engineering units at appropriate locations on the graphicrepresentation.
d. The following information shall be selected from a "pop- up" menu available onvarious graphics:
Quit Trends Alarms Setpoints Messages Module Status Schedules Programming Parameters Schedule Graphs Utilities Schedule Groups
e. Programming, scheduling and set-point changes shall be accessible formodification on each menu for the associated equipment. Operator shall be ableto automatically download changes from the central site to the appropriateprogram for the equipment being controlled. Operator shall be able to uploadinformation from the field modules to the central site.
2. Input Format: Allowable operators, as defined under user access, shall be able tocontrol system functions by their inputs at an appropriate user terminal. The primaryoperator interface shall be via two button mouse.
3. Verification of Operator Input: The system shall acknowledge all inputs as functions orcommands to be performed. The system's handling of operator inputs, such as requeststo start a motor, output a log, change a time program, acknowledge an alarm, or do anyof the other commands described in this specification, shall be in a similar format.
4. Operator Commands: All operator commands shall be in graphics data base and menudriven. After the operator selects the desired object item or menu, the system shalldisplay either the status of selected object item or the allowable options available. Uponentry of a command to the point or points desired as described above, the system shall,before performing any command, request confirmation of the desired command. Systemshall include error monitoring software for user's input error.
5. Output Format: The system shall operate on a System Format basis, regardless of themanner or hardware configuration in which the data is acquired. A "system" shallconsist of a logical grouping of data points, related to a piece of mechanical equipment,an energy distribution system, or an architectural area. For example, in some cases, itmay be desired to display, as a single system, a space temperature with its associatedair handling unit, and in other cases to display all space temperatures on a floor or in abuilding. The DDC shall allow such determinations to be made without regard to thephysical hardware locations of a point or group of points. Likewise, the system shallaccommodate future changes of system grouping and operations without field hardwarechanges.
a. All displays and logs shall contain a header line indicating date, day-of-week, andtime.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 17 ADDENDUM - 01 - 08/20/18
b. All output displays or logs of a point or group of points shall contain, as aminimum, the following information:
1) Graphic presentation of the System2) User name of point3) Point descriptor4) Current value/status5) Associated engineering units6) Alarm description
c. User names, point descriptors, and engineering units shall be operator definableon a per point basis.
6. Setpoints:
a. The system shall utilize a contiguous band of colors each corresponding to actualzone temperatures relative to the desired heating and cooling setpoints. The idealtemperature shall be shown as a green color band. This color band correspondsto the dead band between the onset of mechanical heating or cooling.Temperatures slightly warmer than ideal shall be shown in yellow, and evenwarmer temperature band shall be shown in orange.
b. Temperatures slightly cooler than ideal shall be light blue, and even coolertemperatures shall be shown as dark blue. All alarm colors shall be in red.
c. The system shall be capable of utilizing the mouse operator interface device tochange individual zone temperature setpoints. The change shall be accomplishedby pointing to a graphic temperature bar and by depressing a button, moving themouse cursor to an increased or decreased temperature set-point within thatzone. The system shall also be capable of utilizing the mouse interface device ora conventional keyboard to change a numeric temperature set-point value insteadof utilizing the graphic temperature bar. The floor plan graphic shall then be ableto change colors on a zone by zone basis to reflect the actual temperature in eachzone relative to the changed desired heating or cooling set-point.
d. The system shall be capable of globally changing all setpoints. The global changecapability shall be accessed via a "pop up menu" called by depressing a button onthe mouse.
7. Graphic Structure (controls contractor has the option to demonstrate another option forthis graphical structure, but it must be approved by SJCSD Energy ManagementDepartment prior to installation): The intent of the graphics is to ensure the operator isalways aware of his position within the system as well as how to logically progressthrough the graphical hierarchy to select any desired graphic or other source ofinformation. The GUI will be served as a web page and access from any computerwithout any special software or hardware keys. The building network controller will holdthe graphics for standalone operation. A computer on site will not be acceptable toserve the graphics. The server computer will have the ability to access the system forengineering from the owner, alarming archives and alarms, remote monitoring of thehealth of the communications to the field devices and to archive the trend collectiondata from the building controllers. The web pages will follow a minimum standard asdescribed below:
a. Graphical layout shall be as follows:
1) Main greeting page will have links for all building monitored for quickaccess.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 18 ADDENDUM - 01 - 08/20/18
2) Once a building is selected a picture of the building will be displayedalong with a menu of all systems controlled from this section. Therewill also be links for the floor plans.
3) Once the floor plan has been chosen, the selected graphic page willdisplay the architectural floor plan. This plan will have temperaturereadings and Setpoints of all VAV’s within this floor. There will alsobe links or button depicting the location and equipment number thatis serving that area. This link will hyperlink into the graphic of theAHU. The temperature and setpoint reading will hyperlink to theselected VAV graphic for further review. If the floor has too manyVAV data readings to display for an easy reading the floor plan maybe broken into sections so that the view is easily readable.
4) Graphical VAV – The VAV box will be a graphical representation ofa VAV box. The data shown on the box will be as follows:
i. Box Flowii. Box Flow Trend hyperlinkiii. Box Flow Setpointiv. Box Flow Trend hyperlinkv. Box Flow Min Setpointvi. Box Flow Max Setpointvii. Box Flow Reheat Min Setpoint (if applicable)viii. Reheat Stage Commands (if applicable)ix. Supply Air Temperature (with reheat)x. Room Setpointxi. Room Setpoint Trend hyperlinkxii. Room Temperaturexiii. Room Temperature Trend hyperlinkxiv. Room Humidity (If applicable)xv. Room Humidity Trend hyperlinkxvi. Room Humidity Setpoint (if applicable)xvii. Room Humidity Setpoint Trend hyperlinkxviii. All points above to show a different status color if overridden
5) Graphical AHU – The AHU will be a graphical representation of thephysical air handling unit specified. The data will be located on theAHU as physically located on the unit. The data on the AHU will beas follows:
i. Schedule for Unit hyperlink – link to the scheduling editorii. Schedule for Ventilation hyperlink – link to the scheduling editor.iii. Occupied/Unoccupied status for each scheduleiv. Fan commandv. Fan statusvi. Fan speedvii. Fan VFD alarmviii. Temperature sensors as specified in the control sequence of
operation and trending points
ix. All setpoints as specified in the sequence of operation
1. Example – VAV AHU will have a supply air temperatureand setpoint
x. Supply air static and trend hyperlink
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 19 ADDENDUM - 01 - 08/20/18
xi. Supply air static Setpoint and trend hyperlinkxii. Return air damper positionxiii. Outside air damper positionxiv. Outside air flow and trend hyperlinkxv. Outside air flow setpoint and trend hyperlinkxvi. Outside air heater commandxvii. Outside air heater setpointxviii. Any misc. points needed from a sequence of operationxix. All points above to show a different status color if overridden
6) Graphical Chiller Plant – The plant will be a graphical representationof the physical chiller plant as specified and installed. The data willbe located on the graphical screen as physically installed in theplant.
i. All Chiller interface dataii. Enable/Disable of Chillers and isolation valvesiii. Primary pump command and statusiv. Secondary Pump command, status, speed, and general alarm
from the VFD.v. Flow metersvi. Temperature sensors
7) Misc. Points and graphical screens
b. Graphical representation of text on these screens – The text blocks will have anopposing color for easier reading
c. Graphical representation of the trends – each point to be trended will have an iconnext to the point being trended. This icon will hyperlink to the trending chartbuilder for the individual trend screen. A trend icon on the main building screenwill be a trend chart builder. This trend builder will allow to select multiple trendsfrom a list, pick whether recent trending data or archived (in the server), daterange, etc. Then after selection the trend chart builder will compile the data andbuild the trend for viewing or exporting to a spread sheet. This all happens with astandard web browser.
d. A text block for an over-ridable point shall be highlighted when a mouse is scrolledover an object. When the text block and or pint is overridden the graphical pointwill turn to a different color. This allows for easy viewing of which points areoverridden on a graphic screen.
8. User Access Restriction. Operator sign-on shall require an assignable password.Passwords shall have four levels of system access or user defined:
a. Level 1 - Trainee: The level shall allow readout of data only. The system shalldisplay all operation data base.
b. Level 2 - Maintenance: This level shall allow performance of Level 1 functions plusthe changing of all setpoints.
c. Level 3 - System Programmer: This level shall allow performance of Level 3functions plus the modifying the system configuration.
d. Level 4 - System Manager: This level shall allow performance of Level 4 functionsplus the changing of passwords.
9. Power Failure/Automatic Restart:
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 20 ADDENDUM - 01 - 08/20/18
a. Power failures shall cause the system to go into an orderly shutdown with no lossof program memory.
b. Upon resumption of power, the system shall automatically restart and printout thetime and date of the power failure and restoration at the Central Site.
c. The restart program shall automatically restart affected field equipment. Theoperator shall be able to define an automatic power up time delay for each pieceof equipment under control.
C. User Control Over System Configuration:
1. Database Creation and Modification. All changes shall be done utilizing standardprocedures and be capable of being done while the system is on-line and operational.The system shall allow changes to be made through the portable operator terminal andform the central site. To aid the user, instructive prompting software shall be provided.
2. The system shall permit the operator, with proper password, to perform as a minimumthe following:
a. Add and delete pointsb. Modify point parametersc. Create and modify control sequencesd. Reconfigure application programse. Add and/or modify graphics
3. All data points within the database shall be completely accessible as independent ordependent variables for custom programming, calculation, interlocking, or manipulation.
4. Graphics Software:
a. The graphics software shall permit the easy construction of infinitely variableshapes and sizes through the use of the mouse pointing device.
b. The graphics shall include a digital picture of the school with school name on thefront page of the graphics.
c. A selection of 64 colors and various fill textures, line types and text styles shall allbe accessible through the use of the mouse interface. The software shallresemble many of the computer aided design programs currently available andallow graphics to be easily moved, edited, added or deleted.
d. Graphics software shall be fully implemented and operational to accomplish thefollowing:
1) Create a new graphic picture2) Modify a portion of a graphic picture3) Delete a graphic picture, or any portion thereof4) Call up a graphic picture5) Cancel the display of a graphic picture6) Assign conditions which automatically initiate the display7) Overlay alphanumeric and graphics8) Save the graphic picture9) Display latest process data fully integrated with the graphic display
D. Facility Management Functions:
1. Trend Logging:
a. The system shall be able to trend and display either numerically or graphically any
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 21 ADDENDUM - 01 - 08/20/18
analog or digital points in the system. b. System shall be able to simultaneously graphically display any two trended points
within a module function block or any point in the module versus the outside airtemperature, enthalpy or relative humidity.
c. Each field module shall be capable of storing the most recent 60 samples for eachsingle trend point or the most recent 30 samples for each of two trended pointsfrom one module function block.
d. Each module shall be capable of automatically uploading on a daily basis allaccumulated trend data to the central site for permanent storage on hard disk.
2. Run Time:
a. The system shall provide run time information for all digital output and input pointson command from the operator. Maximum run time limits shall be operatordefinable and shall be capable of automatically issuing a visual when the run timemaximum is exceeded. The operator shall be able to reset the run timeaccumulator.
b. Run time hours and start time date shall be retained in non-volatile modulememory.
c. Each module shall be capable of automatically uploading all accumulated data tothe central site for permanent storage on hard disk.
3. Alarm Conditions and Maintenance Messages:
a. The central site shall allow receipt of alarms and messages while in a functionalmode other than energy management. i.e., Incoming alarms shall be displayedand generate an audible alarm while the operator is utilizing another mode suchas word processing and allow the operator to automatically return to wordprocessing after the alarm is received.
b. The system shall distinguish between alarms and messages with alarms having ahigher priority.
c. The system shall be capable of calling up to three different remote locations todeliver an alarm or message through E-Mail, E-Page or alphanumeric page. Theoperator shall determine if alarms or messages are to be based on temperaturelimit, status or off-normal reporting.
d. The system shall be capable of printing maintenance messages when run timeaccumulation maximum limits are exceeded.
e. The text for operator alarm and messages shall be operator definable. The systemshall be capable of storing at least 100 messages each of any length. Genericmessages used for multiple points throughout the system shall only count as onemessage. In the event the central site is powered down, the alarms shall be storedin the modules until the central site is restored.
f. The central site shall be capable of transferring all alarms to hard disk for storage.
4. Reports and Archiving:
a. The field modules shall be capable of automatically uploading all current andaccumulated data. This shall be delivered to the central server for permanentstorage on hard disk. The system shall further be capable of transferring hard diskinformation onto a digital storage medium or device for remote site storage.
b. The system shall be capable of reporting and archiving the following informationas a minimum:
1) Outside air temperature history and degree day history2) Electric demand and usage history
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 22 ADDENDUM - 01 - 08/20/18
3) All trended points4) All alarms and messages5) Equipment runtime information
c. The system shall also provide the following additional reports for which archivingis not applicable:
1) All points summary2) Building operating schedules3) Printout of any graphic screen
d. The system shall be capable of providing all points summaries on a hierarchicalbasis. e.g., only the points associated with a particular graphic shall be selectableand printed. For example, if the operator is viewing an air handling unit (AHU), hemay request an all points summary at this level and receive only the pointsassociated with the AHU. If the building is being viewed and an all pointssummary selected, all building points will be listed. Similarly, the system shall printbuilding operating schedules pertinent to the graphic level being viewed. e.g., if azone or tenant zone group is being viewed on the graphic display, then the systemshall be capable of printing the building operating schedules for the zone or tenantzone group. If the entire building graphic is being viewed, the system shall becapable of printing schedules at the building level. All systems reports shall becapable to being viewed at the operator’s terminal and printed at the operator'sdiscretion.
E. Direct Digital Control Software:
1. The system shall continuously perform DDC functions at the local DDC controller in astand-alone mode. The operator shall be able to design and modify the control loops tomeet the requirements of the system being operated. The operators shall use systemprovided displays for tuning of PID loops. These displays shall be demonstrated to theowner.
2. Each Controller shall perform the following minimum functions:
a. Identify and report alarm conditionsb. Execute DDC algorithmsc. Execute all application programs indicated on the I/O Summary tabled. Trend and store data
3. In the event of a Controller failure, all points under its control shall be commanded to thefailure mode.
4. All DDC software shall reside in the respective DDC Controller.
F. Application Software: Application software shall be as required to produce the sequence ofoperation specified in the control diagrams as indicated in the contract documents shall befollowed.
PART 3 - EXECUTION
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 23 ADDENDUM - 01 - 08/20/18
3.1 GENERAL INSTALLATION REQUIREMENTS
A. All system components and appurtenances shall be installed in accordance with themanufacturer's instructions and requirements. All necessary interconnections, services andadjustments required for a complete and operable system shall be provided by this contractor.
B. The contractor shall review all contract drawings and specifications, including addenda andreferenced material and shall visit the job site, if applicable in order to become informed prior tobidding as to existing conditions and limitations of the project. The contractor shall bringexceptions and inconsistencies in drawings, specifications, addenda, referenced material, othercontract documents and site conditions to the attention of the engineer.
C. The location of material, equipment and devices shown on the drawings are approximate andare subject to such revisions as may be necessary or desirable at the time that the work isbeing installed. The contractor shall install the work in relation to existing conditions. Shouldproject conditions require rearrangement, or if equipment or accessories can be installed tobetter advantage in a different manner, prepare and submit five copies of shop drawingsindicating the proposed rearrangement for the Engineer's review.
D. Chilled Water Systems: Furnish a test well for installation under Section 23 05 19
E. Meters and Gages for HVAC Piping, adjacent to each temperature sensor where a fixedthermometer is not provided.
F. Control Wiring:
1. All wiring incidental to the building control system, including electrical interlocks shall beincluded in this section and provided as part of the building control system.
2. All control wiring shall be run in conduit where required by code or where the possibilityof harm or permanent damage exist. In addition, all wiring installed below 8 feet orbelow suspended ceilings shall be installed in conduit.
3. Any wiring not installed in conduit shall be multi-conductor cable, with individual wirescolor codes for ease of installation and troubleshooting. All wiring installed above aplenum ceiling shall be Teflon coated and rated for plenum service.
4. All wiring shall be concealed wherever possible, and installed in a neat and workmanlikemanner. All wiring and conduit shall be run parallel or perpendicular to the buildingstructure. All cables shall be supported at frequent intervals and attached to supports bythe use of nylon tie-wraps.
G. Terminal Controls: Unless provided by the terminal manufacturer, Direct Digital Controllerscontrolling VAV boxes, damper operators and velocity transmitters shall be shipped to the VAVbox manufacturer for factory installation. Provide the box manufacturer with complete wiringand piping diagrams and detailed installation instructions. Box manufacturer shall furnish andinstall 24 volt transformer.
H. System Start-up and Check-out:
1. The manufacturer shall provide a control technician for the start-up, check-out of allinput and outputs, implement and check the software function and submit report oncheck-out of each system.
2. Demonstrate to the Owner that all functions are operating as per final approvedsequences.
3. The manufacturer shall provide a control technician for the training of the Owner'soperators as detailed in Division 01 Requirements.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 24 ADDENDUM - 01 - 08/20/18
I. System Acceptance & Trend Log Submittal:
1. After completion of the installation, check-out and control loop tuning, and trend logsshall be submitted, as listed below, to demonstrate the satisfactory performance of thesystem and to serve as a data base for the owner's future use.
2. The trend logs shall be organized in spread sheet format and presented in both tabularand graphical form. A disc or tape copy of each final accepted trend log set shall also beprovided. Trend logs shall be as follows:
3. Control Stability Trend Logs:
a. Each digital or analog output to valves, dampers, adjustable frequency drives andother control devices shall be included.
b. Scan time shall be at five second intervals for a duration of ten minutes.c. Start of the sets shall be immediately after change from one mode to another, i.e.,
unoccupied to occupied, no economizer to economizer, off to on, etc. Only one logwill be required for each output as long as it addresses all controlled elements.
d. Where control of a piece of equipment is by factory furnished packaged controls,then the controlled temperature which is monitored shall be included. Forinstance, where a chiller is controlled by its own control system and control is fromleaving chilled water temperature, then leaving chilled water temperature shall beincluded in the log set.
4. System Operation Trend Logs:
a. Each measured value (temperature, pressure, amps, etc.), equipment status (on-off, percent speed or position, etc.), each mode (unoccupied, cool-down,occupied, etc.), each setpoint and each alarm shall be included.
b. Scan time shall be at operation adjustable intervals with a duration of 24 hours.c. Sets shall be included for cooling only, cooling plus economizer and heating only.
Where start up occurs at a defined season and both heating and cooling cannotbe logged, then the system will be accepted subject to a final demonstration of theother season, when weather permits.
5. Load Profile Trend Log Sets:
a. The total campus load in tons shall be calculated using flow and temperaturedifference between supply and return water.
b. Chiller plant load shall be calculated using chiller flow and temperature differencebetween supply and return water.
c. Static ice system load shall be calculated using ice builder flow and temperaturedifference between the supply and return water.
d. Ice system direct cooling load shall be calculated using heat exchanger flow andtemperature difference between supply and return water. It shall be checked byglycol flow and temperature differential between supply and return glycol.
e. Ice production load shall be calculated glycol flow and temperature difference besupply and return glycol to the chiller.
f. Heat rejection load on water cooled equipment shall be calculated based oncondenser water flow and temperature difference between supply and returnwater.
g. Compressor power input (KWH) shall be calculated based on measured KW orvolts and amps and a look-up table provided by the compressor supplier. Thisshall be logged and converted to tons (KW x 3414 divided by 12,000) andcompared to the compressor tons obtained by subtracting chiller tons fromcondenser tons.
h. Tonnage shall be calculated by averaging six instantaneous readings per hourtaken at ten minute intervals. Tonnage for each of the 24 hours shall be listed.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 25 ADDENDUM - 01 - 08/20/18
6. Energy Use Trend Log Sets:
a. Energy use (KWH) of each chiller compressor shall be calculated using KWH ormeasured volts, amps and a look-up table provided by the manufacturer.
b. Energy use of each dedicated primary chilled water pump, condenser water pumpand cooling tower fan shall be calculated using measured KWH or volts and ampsprorated to motor nameplate data to convert to KW. Chiller auxiliary power use(KWH) shall be added to the chiller power use to get each individual chiller systempower use.
c. Energy use of the secondary chilled water distribution pumps shall be obtained ina similar manner and added to the chiller system energy use to get central planttotal energy use. This shall be compared to the measured central plant KWHwhere available.
d. Energy use of each fan shall be calculated using measured amps and a look-uptable provided by the motor manufacturer to convert to KW.
e. Energy use of constant flow exhaust fans, small pumps, etc. shall be estimatedbased on input data of KW taken from the test and balance data and added basedon fan on or off status.
f. Energy use of the boiler plant shall be calculated using measured gas flow volumeconverted to BTU and/or BTU/Hr.
g. Energy use of the boiler auxiliary including constant flow primary heating waterpump, forced draft blowers and variable flow secondary heating water pumps shallbe calculated based on measured KWH, volts and amps prorated to motornameplate data or amp data taken from the TAB final submittal to convert to KW.
h. The sum of all HVAC power use shall be totaled and listed.i. KWH shall be calculated by averaging six instantaneous KW readings per hour
taken at the same ten-minute intervals as the load measurements. Each chiller,central plant and total building energy use shall be converted to KW/ton and listed.
j. Energy consumption of the entire building shall be taken from the power companymeters and listed.
k. Outdoor air wet bulb shall be listed.l. Data shall be presented for each of the 24 hours each day.m. Energy use shall be presented in bar graph form.
7. Life Safety Trend Logs: A separate set of trend logs shall be developed for each lifesafety system. These shall be in the "change of value" format when going from "normaloperation" to "emergency operation" and shall show the condition of each input device,fan and damper. Where air flow is measured, as in an engineered smoke controlsystem, the air flow in each possible smoke condition shall be included.
8. Custom Trend Log Sets:
a. The operator shall have the ability to customize all trend logs by adjusting bothsampling time and duration.
b. After the initial graph data is accepted, the print-out shall be changed from a fixedinterval to a change of value.
9. Trend Log Design: As a part of the initial submittal process, the proposed trend logformat shall be submitted for approval.
3.2 EQUIPMENT ADDITIONAL REQUIREMENTS
A. Smoke Detectors:
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 26 ©SCHENKELSHULTZ ADDENDUM - 01 - 08/20/18
1. Smoke detectors will be furnished and installed under Division 26. Power wiring, alarmcircuit and supervisory circuit will be provided under Division 26. Control wiring toauxiliary contacts required to shut-down fans (hard wired) and alarm BCS shall beprovided by this Section.
2. All detectors shall function properly, equipment shall shut-down and dampers must betested for operation prior to building occupancy with design air flow to ensure operationunder normal conditions. Provide a letter to the Owners Representative certifying thatthese tests have been conducted.
3. When an engineered smoke control system is specified, the smoke detectors shallfunction as specified.
B. Air Flow Measuring Stations:
1. Install air flow measuring stations on the inlet bells of the fan as specified. 120V2. AC power wiring and control wiring will be provided under this section.3. For airflow measuring stations that cannot be mounted on the inlet bells of the fan,
furnish air flow measuring stations for installation under Section 23 33 00 - Air DuctAccessories wiring will be provided under this section.
4. Coordinate location, duct size and confirm that there is proper space for access beforereleasing for fabrication. Coordinate installation requirements with sheet metal sub-contractor as specified in Section 23 33 00 - Air Duct Accessories.
C. Dampers:
1. Unless specifically stated otherwise, the outside air, return air and relief air dampers forall air handling units shall be provided under this section of the specifications. Wheredamper sizes are not shown on drawings, size outdoor air and relief air dampers at1500 ft/min. and return air dampers at 2000 ft/min. face velocity. Discharge dampersshall be furnished on systems over 5000 CFM. Where so indicated, provide separateminimum and maximum O.A. damper.
2. Return air, relief air and discharge dampers to be smoke rated on systems over 15,000CFM and arranged to close in response to smoke detector or function as specified in anengineered smoke control system.
3. Turn dampers over to sheet metal contractor for installation as specified in Section 2333 00 - Air Duct Accessories.
D. Line Voltage Thermostats: (Used only for exhaust fans only, not for classrooms HVACSystems). Provide and wire including necessary outlet box, conduit box and all interconnectingwiring.
E. Room Temperature Sensors:
1. General:
a. Provide a room temperature sensor in each location shown on the drawings.b. Each room temperature sensor shall be wired to a local control device that shall
maintain the established setpoints within the space in response to time, mode andtemperature inputs.
c. Each sensor shall have a digital display and an override button.
2. Room Temperature Sensor Mounting:
a. In classrooms and offices, each room sensor shall be installed immediately inside
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 27 ADDENDUM - 01 - 08/20/18
door, next to the light switch with its center approximately 4'-0" above the floor. Each room sensor mounted on an exterior wall of the building with an insulating block of wood or other approved material.
b. In public spaces and other unsupervised areas, locate temperature sensors withits center approximately 7'-0" above the floor.
c. Devices with exposed setpoint adjustment, override switches, or any otheroperable feature shall be installed at a height in compliance with ADA for thelocation intended.
F. Thermostat/Temperature Sensor Guard: For schools, install in all public spaces and otherunsupervised areas. Not required in offices or classrooms unless called for on the drawings.
3.3 SOFTWARE ENHANCEMENTS
A. Include an allowance for revisions to the software as required to provide a complete andworkable system consistent with the intent of the specification. All control performance criteriaare specified in the Sequence of Operations section of the specification.
B. After the system has operated properly for 90 days following start-up of the final component ofthe heating and air conditioning systems, an as-built copy of the software shall be transmittedto the owner for permanent record purposes. An allowance shall also be included for anysoftware upgrading or enhancements to improve the system operation or as required for properoperation of the system during the first year of operation. Any changes to the software shall beimmediately transmitted to the owner.
3.4 CALIBRATION AND TESTING
A. The Building Control Contractor shall calibrate all building controlled system equipment andverify operation before this system is placed on-line. All testing, calibrating, and adjusting shallbe completed by the contractor prior to the start of the acceptance test; including all DDCcontrol loops, interlocks, sequences, energy management programs, and alarms shall betested and proper operation verified.
B. The Product Integrated Controls shall be factory installed, configured and tested for stand- alone operation. Specific configuration, such as setpoints and time schedules, shall becompleted before the HVAC equipment on which it is installed and is placed in operation. Alltesting, calibrating and adjusting of individual HVAC equipment PIC controls shall be done as apart of that individual unit start-up and acceptance. Only the PIC's network communicationsfunction shall be included with the automation (BCS) acceptance test.
3.5 ACCEPTANCE TEST
A. After start-up and calibration, the building controls sub-contractor shall submit to the engineertrend logs of all points on each system demonstrating stable and proper operation. Thedemonstration shall cover the following conditions:
1. Cooling Only (O.A. Temperature > 70°F).2. Cooling and Heating (O.A. Temperature 55°F to 70°F).3. Heating Only (O.A. Temperature < 40°F).
B. The trend logs shall be as follows:
1. 24 hour period at 15 minute intervals.2. 3 hour start-up period at 5 minute intervals.3. A total of two sets covering two days during each period are required.
MILL CREEK K-8 CONVERSION St. Johns County School District
#1820108 ©SCHENKELSHULTZ
INSTRUMENTATION AND CONTROL DEVICES FOR HVAC 23 09 23 - 28 ADDENDUM - 01 - 08/20/18
C. After submission of the logs for any one of the periods, the engineer will review them foracceptability, and if acceptable, schedule a final walk-thru of the system for final acceptanceand start of hardware warranty.
D. During the hardware warranty period, the controls sub-contractor shall submit trend datacovering the other two periods. Any adjustments or modifications to get acceptable results ineach period shall be considered to be part of the warranty obligation.
E. Upon completion of the project installation, a hard copy (disc based) backup of the installed jobpoint, program, and graphics databases shall be provided by the vendor. This backup, whenused with the server software and support tools provided by the vendor, shall allow full siterestoration onto a new/replacement server platform in the event of a hard drive failure of theprimary server. This will be the last step in the final acceptance process.
3.6 SEQUENCE OF OPERATION
A. Refer to the control diagrams as indicated in the contract documents for actual system andequipment details.
END OF SECTION 23 09 00
CARPET
DESCRIPTION
COLOR SCHEMES WHERE PATTERN OCCURS
LUXURY VINYL TILE ( NOT PATTERNED )
INDICATION
FLOORCPT
FINISH
LVT
LVT-A
LVT-C
LVT-B
LVT-D
F I N I S H S C H E D U L E
PMT-1
SEALED CONCRETESC
PORCELAIN FLOOR TILE
WOOD FLOORING SYSTEM @ GYM (SEE SPECS)WD-GEPOXY FLOORINGEPX
RECESSED (WALK-OFF) FLOOR GRILLEWALK-OFF GRILLE
FIXED FLOOR MATFLOOR MAT
POLISHED CONCRETEPC
comm no.:
SS Lic. No. −schenkelshultz.comfaxvoice
SCHENKEL SHULTZA R C H I T E C T U R E
date:
drawn:checked: sheet reference:
revisions:
project :
detail reference:
1820108
200 E. Robinson StreetSuite 300Orlando, Fl 32801
407−872−3322407−872−3303
AA-C000937A311, A312, A313
MILL CREEK K−8 CONVERSION
1
1
1
NHANHA / DT8/20/2018
SKA-2 1 ADDENDUM NO. 1
FINISH SCHEDULE
8/A903
GALVANIZED POSTS,MESH, AND RAILS
NOTE:END POSTS: 3" DIA. INTERMEDIATE POSTS: 3" DIA.
20' - 0"
10' -
0"
8"6'
- 0"
2'-0" DIA. CONC. FOOTINGS (TYP.)
2' - 0"
comm no.:
SS Lic. No. −schenkelshultz.comfaxvoice
SCHENKEL SHULTZA R C H I T E C T U R E
date:
drawn:checked: sheet reference:
revisions:
project :
detail reference:
1820108
200 E. Robinson StreetSuite 300Orlando, Fl 32801
407−872−3322407−872−3303
AA-C000937A903
MILL CREEK K−8 CONVERSION
1/4" = 1'-0"
7 BACKSTOP DETAIL
NHANHA / DT8/20/2018
SKA-3 1 ADDENDUM NO. 1
NEW DETAIL
1
FINISH GRADE
CONCRETE FOOTINGS
GALVANIZED POSTS,MESH, AND RAILS
NOTE:END POSTS: 3" DIA. INTERMEDIATE POSTS: 3" DIA.
8"6'
- 0"
2'-0" DIA. CONC. FOOTINGS (TYP.)
2' - 0"
10' -
0"
comm no.:
SS Lic. No. −schenkelshultz.comfaxvoice
SCHENKEL SHULTZA R C H I T E C T U R E
date:
drawn:checked: sheet reference:
revisions:
project :
detail reference:
1820108
200 E. Robinson StreetSuite 300Orlando, Fl 32801
407−872−3322407−872−3303
AA-C000937A903
MILL CREEK K−8 CONVERSION
1/4" = 1'-0"
8 BACKSTOP SECTION
NHANHA / DT8/20/2018
SKA-4 1 ADDENDUM NO. 1
NEW DETAIL
1
1
comm no.:
SS Lic. No. −schenkelshultz.comfaxvoice
SCHENKEL SHULTZA R C H I T E C T U R E
date:
drawn:
checked: sheet reference:
revisions:
project :
detail reference:
ADDENDUM NO. 11
1820108
200 E. Robinson Street
Suite 300
Orlando, Fl 32801407−872−3322
407−872−3303
AA-C000937
CJF
CJF M101
08/20/18
SKM−1MILL CREEK K−8 CONVERSION
FLOOR PLAN
1
comm no.:
SS Lic. No. −schenkelshultz.comfaxvoice
SCHENKEL SHULTZA R C H I T E C T U R E
date:
drawn:
checked: sheet reference:
revisions:
project :
detail reference:
ADDENDUM NO. 11
1820108
200 E. Robinson Street
Suite 300
Orlando, Fl 32801407−872−3322
407−872−3303
AA-C000937
CJF
CJF M102
08/20/18
SKM−2MILL CREEK K−8 CONVERSION
FLOOR PLAN
1
comm no.:
SS Lic. No. −schenkelshultz.comfaxvoice
SCHENKEL SHULTZA R C H I T E C T U R E
date:
drawn:
checked: sheet reference:
revisions:
project :
detail reference:
ADDENDUM NO. 11
1820108
200 E. Robinson Street
Suite 300
Orlando, Fl 32801407−872−3322
407−872−3303
AA-C000937
CJF
CJF M702
08/20/18
SKM−3MILL CREEK K−8 CONVERSION
CHILLED WATERLOOP DIAGRAM
comm no.:
SS Lic. No. −schenkelshultz.comfaxvoice
SCHENKEL SHULTZA R C H I T E C T U R E
date:
drawn:
checked: sheet reference:
revisions:
project :
detail reference:
ADDENDUM NO. 11
1820108
200 E. Robinson Street
Suite 300
Orlando, Fl 32801407−872−3322
407−872−3303
AA-C000937
HLN
MCC E704
08/20/18
SKE−1MILL CREEK K−8 CONVERSION
3
1
comm no.:
SS Lic. No. −schenkelshultz.comfaxvoice
SCHENKEL SHULTZA R C H I T E C T U R E
date:
drawn:
checked: sheet reference:
revisions:
project :
detail reference:
ADDENDUM NO. 11
1820108
200 E. Robinson Street
Suite 300
Orlando, Fl 32801407−872−3322
407−872−3303
AA-C000937
HLN
MCC E704
08/20/18
SKE−2MILL CREEK K−8 CONVERSION
1
1
sheet reference:
revisions:
detail reference:
comm no.:
SS Lic. No. −
schenkelshultz.comfaxvoice
SCHENKEL SHULTZA R C H I T E C T U R E
date:
drawn:
checked:
project : ADDENDUM NO. 11
E601
SKE−3
POWER RISERDIAGRAM
1820108
200 E. Robinson Street
Suite 300
Orlando, Fl 32801407−872−3322
407−872−3303
AA-C000937
HLN
MCC
08/20/18
MILL CREEK K−8 CONVERSION
1
1
sheet reference:
revisions:
detail reference:
comm no.:
SS Lic. No. −
schenkelshultz.comfaxvoice
SCHENKEL SHULTZA R C H I T E C T U R E
date:
drawn:
checked:
project : ADDENDUM NO. 11
E601
SKE−4
POWER RISERDIAGRAM
1820108
200 E. Robinson Street
Suite 300
Orlando, Fl 32801407−872−3322
407−872−3303
AA-C000937
HLN
MCC
08/20/18
MILL CREEK K−8 CONVERSION
1
sheet reference:
revisions:
detail reference:
comm no.:
SS Lic. No. −
schenkelshultz.comfaxvoice
SCHENKEL SHULTZA R C H I T E C T U R E
date:
drawn:
checked:
project : ADDENDUM NO. 11
E601
SKE−5
POWER RISERDIAGRAM
1820108
200 E. Robinson Street
Suite 300
Orlando, Fl 32801407−872−3322
407−872−3303
AA-C000937
HLN
MCC
08/20/18
MILL CREEK K−8 CONVERSION
1
sheet reference:
revisions:
detail reference:
comm no.:
SS Lic. No. −
schenkelshultz.comfaxvoice
SCHENKEL SHULTZA R C H I T E C T U R E
date:
drawn:
checked:
project : ADDENDUM NO. 11
E602
SKE−6
FIRE ALARMANDGROUNDINGRISERDIAGRAMS
1820108
200 E. Robinson Street
Suite 300
Orlando, Fl 32801407−872−3322
407−872−3303
AA-C000937
HLN
MCC
08/20/18
MILL CREEK K−8 CONVERSION
1
1
sheet reference:
revisions:
detail reference:
comm no.:
SS Lic. No. −
schenkelshultz.comfaxvoice
SCHENKEL SHULTZA R C H I T E C T U R E
date:
drawn:
checked:
project : ADDENDUM NO. 11
E602
SKE−7
FIRE ALARMANDGROUNDINGRISERDIAGRAMS
1820108
200 E. Robinson Street
Suite 300
Orlando, Fl 32801407−872−3322
407−872−3303
AA-C000937
HLN
MCC
08/20/18
MILL CREEK K−8 CONVERSION
1