genuine metaris orbital motor technical catalog€¦ · genuine metaris orbital motor technical...

www.metaris.com www.hydraulex.com

Genuine MetarisOrbital Motor Technical CatalogLow Speed High Torque Orbital Motors

2 Hydraulex Global Genuine Metaris Orbital Motors Technical Catalog

Genuine Metaris Orbital Motors Technical CatalogLow Speed High Torque Disc Valve & Spool Valve Motors

Series Replacement for: Page

Technical Information ALL 3

MMPS

Danfoss® DH, DS, OMP, OMR SeriesChar-Lynn® H(101-), S(103-), T(158-) SeriesParker® TB, TC SeriesWhite® HB(300), RS(200/201), WD(145/146), WG(275/276/277/278/280/281), WP(155/156), WR(255/256) Series

6

MMRSW

Danfoss® OMEW SeriesChar-Lynn® W(162-) SeriesParker® TJ, TF, TL SeriesWhite® WG(275/276) Series

16

MMH

Danfoss® OMH Series

Parker® TG Series

24

MMW

Char-Lynn® W(162-) SeriesParker® TF, TG, TH SeriesWhite® CE(400/401/420/421), HB(300), RE(500/501) Series

31

MMS

Danfoss® OMS SeriesChar-Lynn® 2000(104-, 105-, 106-) SeriesParker® TE, TF SeriesWhite® DR(600/620), HB(300), RE(500/501/520/521), WS (350/351/355/356/357/358) Series

38

MMK

Danfoss® TMT SeriesChar-Lynn® 4000(109-, 110-, 111-) SeriesParker® TG SeriesWhite® DT (700) Series

54

MMT

Danfoss® OMT SeriesChar-Lynn® 6000(112-, 113-, 114-) SeriesParker® TK SeriesWhite® DT(700), D9(800) Series

67

MMV

Danfoss® OMV SeriesChar-Lynn® 10000(119-) Series

White® DT(700), D9(800) Series

78

Special Options ALL 87

Spool Valve

Disc Valve

All measurements are in inches (millimeters) unless otherwise marked.

All manufacturers names, symbols and descriptions in this document are used for reference purposes only, and it is not implied that any parts listed is the product of these manufacturers.

Contents

Hydraulex Global Genuine Metaris Orbital Motors Technical Catalog 3www.hydraulex.com


Technical Information - All SeriesShaft Seal Specifications/Benefits� � Genuine Metaris Motors incorporate a high pressure shaft seal which allows higher back pressures� � Case drain line is recommended when back pressure exceeds individual performance data table� � Increases ability to handle high pressure spikes

Recommended Fluid Specifications� � Anti-wear hydraulic oil� � Viscosity of 172 - 334 SUS (37 - 73 cSt)� � Recommended oil cleanliness - ISO4406 = 18/13� � Maximum recommended operating temperature - 80°C (176°F)

Pressure and Speed Operation Parameters� � Simultaneous maximum RPM and maximum pressure NOT recommended� � Maximum pressure or maximum RPM operation: 10% of every minute� � Intermittent pressure is the allowed pressure at the inlet port� � Continuous pressure is the working pressure difference between inlet and outlet ports

Start-up Procedures (to assure best motor life)� � Ensure motor is filled with equipment manufacturers’ recommended fluids prior to any load application� � Operate motor at 30% of rated pressure for at least one hour before application of full load

Rotation - Port Plumbing

Standard Rotation:(Viewed from the shaft end)

• Port A Pressurized = Clock-wise Rotation (CW)• Port B Pressurized = Counter Clock-wise Rotation (CCW)

Opposite Rotation:(Viewed from the shaft end)

• Port A Pressurized = Counter Clock-wise Rotation (CCW)• Port B Pressurized = Clock-wise Rotation (CW)



Technical Information - All SeriesCase Drain InformationAll Genuine Metaris motors will be supplied with a case drain and shipped with a Steel Hex Socket Plug installed

� � Advantages provided by use of a case drain� � Contamination control - flushing the motor case� � Cooler operating temperatures - exiting oil draws motor heat away� � Extended motor seal life - maintains lower case pressure (due to the fact of a pre-installed preset restriction valve)

Plumbing Diagrams

Parallel Connection Series Connection



GeroterFixed Lobes on Ring:· Higher Friction· Lower Mechanical Efficiency· Lower Start-up Torque· Jerky Low Speed Operation· Greater Wear on Lobes = Shorter Life· Lower Price Point

Roller-StarRotating Rollers on Ring:· Lower Friction· Higher Mechanical Efficiency· Higher Start-up Torque· Smooth Low Speed Operation· Less Wear on Rollers = Longer Life· Higher Price Point*(*Metaris offers the Roller-Star version at the Geroter Price Point.)

Technical Information - All SeriesMotor Testing� � Motors are tested prior to painting

� � Tested� � Cleaned� � Heated and dried� � Painted while warm

� � Test report provided with each unit

� � High quality standards maintained� � Volumetric efficiency 85% or higher� � 10% re-tested by QC Department

Geroter vs Roller-Star� � All Genuine Metaris Orbital Motors incorporate Roller-Star design� � Roller-Star technology at Geroter prices� � Provides longer operational life



· Simultaneous maximum torque & maximum speed NOT recommended.· Continuous Rating » (Cont.) motor may be run continuously at these ratings.· Intermittent Operation » (Int.) 10% of every minute.· ∆ - True pressure difference between inlet port and outlet port.· Maximum case pressure without case drain -- 1” Shaft = 125 Bar (1813 psi) | Greater than 1” Shaft 75 Bar (1088 psi).

MMPS SeriesFeaturesMMPS series motors are spool valve motors that can be used in parallel or series configurations. A diverse offering of mounting flanges, shafts, ports, and displacements allow for easy installation, product replacement or OEM application.

� � Advanced Roller-Star technology, requiring lower pressure at start-up and providing smoother operation at all speeds

� � High efficiency shaft bearing, which allows higher pressure, speed and radial force

� � High pressure shaft seal, which allows for higher back pressures and an increased ability to handle high pressure spike conditions

� � Internal integrated check valve, which limits case pressure by blocking the high pressure port side and allowing the motor housing to drain into the outlet (low pressure) port

� � Motors connected in series will utilize the case drain

MODEL CODE (DISPLACEMENT) 01 02 03 04 05 06 07 08 09 10 11

Displ.cm³/r 50 63 80 100 125 160 200 250 305 370 395

in³/r 3.1 3.8 4.9 6.1 7.6 9.8 12.2 15.3 18.6 22.6 24.1

Flow

LPMCont. 38 53 53 53 53 53 53 53 53 53 53

Int. 45 57 57 57 57 57 57 57 57 57 57

GPMCont. 10.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0

Int. 11.9 15.1 15.1 15.1 15.1 15.1 15.1 15.1 15.1 15.1 15.1

Max Speed RPM

Cont. 750 778 635 510 430 329 266 213 171 142 133

Int. 875 832 680 537 420 347 281 226 182 150 141

Pressure

∆BarCont. 138 138 138 138 138 124 124 124 103 83 83

Int. 155 155 155 155 155 138 138 127 110 90 90

∆PSICont. 2002 2002 2002 2002 2002 1798 1798 1798 1494 1204 1204

Int. 2248 2248 2248 2248 2248 2002 2002 1842 1595 1305 1305

Torque

NMCont. 93 123 155 196 230 271 328 401 417 402 429

Int. 105 138 174 219 256 297 359 410 441 427 458

LBF-INCont. 823 1089 1372 1735 2036 2399 2903 3549 3691 3558 3797

Int. 929 1221 1540 1938 2266 2629 3177 3629 3903 3779 4054

Specifications



Series

Displacement in³/r (cm³/r) 01 = 3.1 (50)02 = 3.8 (63)03 = 4.9 (80)04 = 6.1 (100)05 = 7.6 (125)06 = 9.8 (160)07 = 12.2 (200)08 = 15.3 (250)09 = 18.6 (305)10 = 22.6 (370)11 = 24.1 (395)

Flange & PilotA = 2-Bolt SAE “A”, pilot Ø3.25” (82.5) x .31” (8) StaggeredB = 4-Bolt SAE “A”, pilot Ø3.25” (82.5) x .31” (8) StaggeredC = 2-Bolt SAE “A”, pilot Ø3.25” (82.5) x .11” (2.8) InlineD = 4-Bolt SAE “A”, pilot Ø3.25” (82.5) x .11” (2.8) InlineE = 4-3/8-16 Square-flange, pilot Ø1.75” (44.4) x .11” (2.8) InlineF = 4-M10x1.5 Square-flange, pilot Ø1.75” (44.4) x .11” (2.8) Inline

PaintA = No PaintB = Blue (Standard)C = BlackOptions A & C (or any other color needed) will only be considered for Large Quantity Orders

RotationA = Standard (Clock-wise)B = Opposite (Counter Clock-wise)

Drain Port1 = G 1/4 BSP2 = 7/16”-20UNF3 = M14x1.54 = PT(RC) 1/4”5 = M10x1All motors come with a Steel Hex Socket Plugged Drain Port

PortsA = G 1/2, BSPB = 1/2”-14NPTFC = M18x1.5D = 7/8”-14UNF, O-ringE = G 1/2, O-ringF = M22x1.5G = 4-5/16”-18UNC (Manifold)H = 4-M8x1.5 (Manifold)I = PT(RC) 1/2”J = M20x1.5

MMPS - 01 - A - 01 - D - 2 - B - A

Shafts01 = .984” (25mm) Straight, Flat key 8 x 7 x 3202 = 1” (25.4mm) Straight, Flat key 6.35 x 6.35 x 3203 = 1” (25.4mm) SAE 6B Splined - M8 Tap (European)04 = 1.26” (32mm) Straight, Flat key 10 x 8 x 4505 = 1.25” (31.75mm) Straight, Flat key 7.96 x 7.96 x 3206 = 1.25” (31.75mm) Tapered Shaft, Flat key 7.96 x 7.96 x 3207 = 1.26” (35mm) Tapered Shaft, Flat key 6 x 6 x 2008 = 1.25” (31.75mm) 14t Splined09 = 1” (25.4mm) Straight, Woodruff key10 = 1” (25.4mm) SAE 6B Splined - 1/4” -20 Tap11 = 1” (25.4mm) Straight, with 0.315” dia. crosshole12 = 1” (25.4mm) Straight, with 0.406” dia. crosshole13 = .875” (22.23mm) Straight14 = .875” (22.23mm) SAE B Shaft 13t Splined15 = .984” (25mm) Straight, 8mm keyway16 = 1” (25.4mm) Tapered Shaft, with Woodruff Key and Nut17 = 1” (25.4mm) Straight, with 0.406” dia. crosshole & 6.35 x 6.35 x 32 Flat key

MMPS SeriesModel Code Breakdown



MMPS SeriesPerformance InformationTo assure best motor life, run motor for approximately one hour at 30% of rated pressure before applying full load.Fill motor with equipment manufacturer’s recommended fluid prior to any load application and startup.

Side Load

Shaft Seal



50 cc/r∆ PRESSURE BAR

28 55 69 97 110 124 138 155

FLOW

LP

M

7.6 18152

37147

46142

64134

72124

15.1 18298

37290

47276

66265

75261

84245

93243

22.7 17450

37438

47434

66419

75410

84407

93389

105373

30.3 14603

35590

44583

64584

74554

83545

92536

104520

37.9 14750

34738

44732

64713

73702

83696

92682

104661

45.4 43875

62859

72844

81835

91819

102804


28 55 69 97 110 124 138 155

FLOW

LP

M

7.6 22111

47107

59105

8096

9192

15.1 24229

50216

62212

87194

99190

110186

122183

22.7 22343

48334

60321

86319

99315

111291

123288

138276

30.3 21451

47442

60431

86419

98415

111412

123401

138386

37.9 18565

45552

58547

84532

97525

110512

122504

137496

45.4 18678

44665

57658

82641

95635

109623

121612

137601

53.0 42778

55771

81753

95746

107733

120723

135711

56.8 40832

53826

80806

93800

106786

119779

135766


28 55 69 97 110 124 138 155

FLOW

LP

M

7.6 3090

6183

7780

10670

11963

15.1 30185

62179

78175

109166

124162

140156

155150

22.7 29275

61267

77265

109253

124248

140240

155232

174221

30.3 27367

60359

76354

108343

124338

139333

155324

174313

37.9 26460

58450

74446

106435

122428

138420

153412

173399

45.4 24552

56543

72537

105523

121515

136509

152500

172487

53.0 54635

70630

102616

118609

134599

150592

170578

56.8 52680

69673

101660

117650

133642

149634

168619


28 55 69 97 110 124 138 155FL

OW

LPM

7.6 3971

7966

9883

13556

15251

17146

15.1 38146

79141

99138

139131

158128

177124

195118

22.7 37217

78211

98208

139199

158195

178190

196184

219174

30.3 36290

76284

97280

137217

157267

177262

195255

218245

37.9 33363

74355

95351

135343

155337

174332

193325

217315

45.4 31436

72429

92424

133414

153409

173402

192395

215384

53.0 27510

69501

90497

130487

150482

170475

189469

213456

56.8 67537

88532

128522

148516

168510

187502

211490


28 55 69 97 110 124 138

FLOW

LP

M

7.6 6145

12342

15340

20934

23530

26125

15.1 6195

12491

15590

21485

24282

26978

29573

22.7 59140

123136

155134

215129

243125

271121

297114

30.3 57187

121183

152181

213175

242172

270166

296259

37.9 53234

117230

149227

209222

239218

266211

293203

45.4 49282

114277

146274

206269

235265

263257

291248

53.0 45329

109323

141321

201316

230311

259304

287296

56.8 107347

139344

198339

228334

257327

284318


28 55 69 97 110 124 138 155

FLOW

LP

M

7.6 4856

9651

12150

16644

18940

21234

15.1 48114

95111

121110

166107

189105

21198

24090

22.7 47172

95171

120168

166157

188155

212151

240145

271130

30.3 46230

96225

120220

165216

187212

213206

239200

270190

37.9 45287

95283

120278

165272

185267

210260

237253

270240

45.4 44345

94341

118335

162328

183323

210317

235310

269300

53.0 38405

90401

115395

154390

180384

202378

228371

260358

56.8 82426

108424

143420

170415

195410

210404

245390

MMPS SeriesPerformance Information

Continuous

Intermittent

27510

(Torque Nm)

(Speed RPM)




28 55 69 97 110 114 125 127

FLOW

LP

M

7.6 9429

18726

23024

30617

15.1 9562

19259

23559

31955

35950

36849

22.7 9391

19189

23688

32182

36178

37176

40172

41071

30.3 89122

187120

233119

319113

359108

369106

399101

40899

37.9 84152

182150

288148

313143

356136

366134

396127

406125

45.4 78183

175180

222179

309173

351166

361166

392156

402153

53.0 71213

169211

216209

302202

345195

356193

386185

397182

56.8 165226

212224

298217

341209

352207

383200

394197


28 41 55 69 83 97 103 110

FLOW

LP

M

7.6 11723

17622

23021

28319

32916

36611

15.1 11949

18048

23748

28947

34247

39144

41641

22.7 11674

17872

23772

29071

34269

39164

41762

44160

30.3 11098

17297

23297

28596

33994

39089

41486

43883

37.9 105122

166121

226120

280120

334117

385112

410108

435104

45.4 98146

159145

216145

271145

326142

379136

404131

428127

53.0 89171

151170

209170

264169

318165

371159

397154

423150

56.8 204182

258181

313177

366171

393165

419160


14 28 41 55 69 83 90FL

OW

LPM

7.6 6720

14019

21018

27217

33415

15.1 6641

14341

21540

28340

34239

40238

43037

22.7 6561

14160

21460

28359

34258

40057

42856

30.3 5682

13181

20680

27779

33678

39777

42777

37.9 50102

126102

199101

270101

331100

39397

42496

45.4 38122

120121

191120

255119

318119

383118

416116

53.0 26142

108141

182140

249139

310138

375137

408134

56.8 242150

303149

370147

403146


14 28 41 55 69 83 90

FLOW

LP

M

7.6 7118

15017

22417

29016

35614

15.1 7038

15238

22937

30237

36536

42936

45835

22.7 6957

15057

22857

30255

38554

42753

45652

30.3 6277

14076

22075

29574

35873

42372

45572

37.9 5396

13496

21295

28895

35394

41991

45290

45.4 40114

129113

204112

272111

339111

408110

444108

53.0 28133

115132

194131

267130

330129

400128

435125

56.8 258141

323140

394138

430137

MMPS SeriesPerformance Information Cont.

Continuous

Intermittent

26142

(Torque Nm)

(Speed RPM)


28 55 69 97 110 124 138

FLOW

LP

M

7.6 7636

15233

18731

25325

28320

15.1 7677

15473

19173

25968

29265

32461

35555

22.7 74113

154110

192109

263104

294100

32895

35987

30.3 72151

150148

189146

260142

293139

326132

359123

37.9 67189

146186

185184

255181

290176

323166

355156

45.4 62228

142224

182222

251219

286213

320204

353192

53.0 56266

137261

176259

246256

291251

315242

348229

56.8 133281

172279

242275

278269

313260

346247

Individual Performance Data Graph Information:

• Motors run with high efficiency in all areas designed with a number for torque and speed.

• However, for best motor life, select a motor to run with a torque and speed range shown in the light gray area (Continuous).

• Performance data is typical at 120 SUS (25.2 cSt).• Actual data may vary slightly from unit to unit in production.



MMPS SeriesDimensions - Staggered Ports (Flanges A & B)

.31 (8.0)

Flange Port APort B

4-M8

Case Drain Port:Noneor M14x1.5or G1/4”or 7/16-20UNF

Shaft

1.50 (38) 1.42 (36).79 (20) .79 (20)

Ø3.62 (92)

10.9.71 (18)

.71 (18)

.63 (16)

.79 (20) .79 (20)

X(Displ. Width)

Y

DISPLACEMENT CM³/R 50 63 80 100 125 160 200 250 305 370 395

XInches .35 .45 .57 ,71 ,90 1.14 1.40 1.76 2.21 2.67 2.84

Millimeters (9) (11.5) (14.4) (18.1) (22.8) (29.0) (35.6) (44.7) (56.0) (68.0) (72.0)

YInches 5.64 5.74 5.85 6.00 6.19 6.43 6.69 7.04 7.49 7.96 8.12

Millimeters (143.3) (145.8) (148.7) (152.4) (157.1) (163.2) (170.0) (178.9) (190.3) (202.2) (206.3)

PORT

2-7/8-14UNF O-ring 2-M18x1.5

2-1/2-14NPTF 2-M20x1.5

2-G1/2 (BSP) 2-M22x1.5

2-3/4-16 O-ring 2-PT1/2

Dimensions are in inches (millimeters).



Case Drain Port:G1/4” (BSP)or 7/16-20 O-ringor M14x1.5

Standard Motor End Cap

Groove Provided for 3.25” (82.6) I.D. x .10” (2.65)Cross section O-ring

MMPS SeriesDimensions - Aligned Ports (Flanges C, D, E, F, G, H, I, J)


XInches .35 .45 .57 .71 .90 1.14 1.40 1.76 2.21 2.67 2.84

Millimeters (9) (11.5) (14.4) (18.1) (22.8) (29.0) (35.6) (44.7) (56.0) (68.0) (72.0)

YInches 5.76 586 5.97 6.12 6.30 6.54 6.81 7.17 7.61 8.08 8.24

Millimeters (146.3) (148.8) (151.7) (155.4) (160.1) (166.2) (173.0) (182.0) (193.3) (205.2) (209.3)

Ø3.62 (92)

X(Displ. Width)

PORTS - C, D, E, F, I & J

2-7/8-14UNF O-ring 2-M18x1.5

2-1/2-14NPTF 2-M20x1.5

2-G1/2 (BSP) 2-M22x1.5

2-3/4-16 O-ring 2-PT1/2

PORTS - G & H

4-5/16-18UNC

4-M8x1.5 deep 13 min

2-G1/2 (BSP)

2-3/4-16 O-ring

10.9

Shaft

Port B

Port A

Y

.63 16).11 (2.8)

1.68 (42.7)

1.80 (45.7)

1.68 (42.7)

1.80 (45.7) 2.50 (63.5)

1.25 (31.75)

.56 (14.2)

4-5/16-18UNC or4-M8x1.5 deep 13 min

1.12 (28.4)




MMPS SeriesMounting Flanges

2.17” (55) 2.17” (55)

1.97” (50)

45°

5.17

” (13

1.4)

max

5.17

” (13

1.4)

max

5.17

” (13

1.4)

max

3.81” (96.8) max

3.28

” (83

.3) m

ax

3.28” (83.3) max

4.19

” (10

6.4)

4.19

” (10

6.4)

2- Ø.53” (13.5) 4- Ø.53” (13.5)

22.5° 22.5°

Ø4.19” (106.4)

2- Ø.53” (13.5)

3/8”-16 UNC

Pilot:Ø3.25” (82.5)

Ø3.25” (82.5)

A = 2-Bolt SAE “A”, Long Pilot .31” (8mm) B = 4-Bolt SAE “A”, Long Pilot .31” (8mm)

C = 2-Bolt SAE “A”, Pilot .11” (2.8mm) D = 4-Bolt SAE “A”, Pilot .11” (2.8mm)

E = 4-3/8”-16 Square-flange F = 4-M10x1.5 Square-flange

Pilot:Ø3.25” (82.5)

2.17” (55)

5.17

” (13

1.4)

max

4- Ø.53” (13.5)

22.5° 22.5°

Ø4.19” (106.4)

Pilot:Ø3.25” (82.5)

Pilot:Ø3.25” (82.5)

Pilot:Ø1.75” (44.4)

45°

3.28

” (83

.3) m

ax

3.28” (83.3) max

M10x1.5

Ø3.25” (82.5)

Pilot:Ø1.75” (44.4)




MMPS SeriesShafts

1 = .984” (25mm) Straight, Flat Key 8x7x32 5 = 1.25” (31.75mm) Straight, Flat Key 7.96x7.96x32

3 = 1” (25.4mm) SAE, 6B Splined 7 = 1.38” (35mm) Tapered, Flat Key 6x6x20

2 = 1” (25.4mm) Straight, Flat Key 6.35x6.35x32 6 = 1.25” (31.75mm) Tapered, Flat Key 7.96x7.96x32

4 = 1.26” (32mm) Straight, Flat Key 10x8x45 8 = 1.25” (31.75mm) 14t Splined

2.18” (55.3) max 2.18” (55.3) max

2.18” (55.3) max 2.28” (58)

2.18” (55.3) max

2.68” (68) max

1.81” (46 ± 0.3) 1.81” (46 ± 0.3)

1.7” (43.2) 1.42” (36)

1.81” (46 ± 0.3)

2.17” (55 ± 0.3) 1.81” (46)

.79” (20) .79” (20)

.79” (20) .79” (20) .51” (13)

.16” (4)

.79” (20)

Ø.16” (4)

.79” (20) .79” (20)

.20” (5) .20” (5)

Ø.18” (4.5)

.20” (5).5” (12.7)

.20” (5)1:8∇

.20” (5)

.31” (8) .31” (8)

.25” (6-6.25 ± 0.05)

Ø.85” (21.47 ± 0.07) .24” (6)

.25” (6.35)

.31” (7.9)

.39” (10)

1.1” (28) 1.38” (35)

.75” (19)

1.1” (28).67” (17)

1.38” (35)

1.26” (32) 1.26” (32)

1.04” (26.4)

1.26” (32) 1.39” (35.4)

1.26” (32)

1.77” (45) 1.30” (33)

Ø.9

8” (2

5)

Ø1.

25” (

31.7

5)

Ø.9

96” (

25.3

2)

Ø1.38” (35)

Ø1”

(25.

4)

Ø1.

25” (

31.7

5)

Ø1.

26” (

32)

Ø1.

25” (

31.7

5)

M8

3/8-

16UN

C

M8

M20

x1.5

1.73

” (44

)

M8

1-20

UNEF

M8

3/8-

16UN

C

1:10∇




MMPS SeriesShafts Cont.

9 = 1” (25.4mm) Straight, Woodruff Key 13 = .875” (22.23mm) Straight, Flat Key 6.35x6.35x32

11 = 1” (25.4mm) Straight with .315 dia. Crosshole 15 = .984” (25mm) Straight, 8mm Keyway

10 = 1” (25.4mm) SAE 6B Splined 14 = .875” (22.23mm) SAE B 13t Splined

12 = 1” (25.4mm) Straight with .406 dia. Crosshole 16 = 1” (25.4mm) Tapered, Woodruff Key & Nut

1.77” (45) 1/4-20UNC-2BDeep 14.2 min

1/4-20UNC-2BDeep 14.2 min

Ø.315” (8 ± 0.05)

1” (25.4) x .25” (6.35)

1.5” (38)

1.77” (45)

2.01” (51)

1.5” (38)

.51” (13 ± 0.5)

Ø.16” (4)

.96” (24.5)

.45” (11.5)

.25” (6.35)

.12” (3.10 ± 0.2)

.75” (19) 1” (25.4)

.27” (6.9)/ .19” (4.8)

.26” (6.6)/ .18” (4.6)

Ø.73” (18.5 ± 0.1)

1.38” (34.9)1.46” (37.1)

2.43” (61.8) / 2.37” (60.2)

Ø1”

(25.

4)

1.11

” (28

.2)

Ø.8

7” (2

2)

.98”

(25)

Ø.9

97” (

25.3

25 ±

0.0

25)

Ø1”

(25.

4)

Ø.8

7” (2

2 ±

0.1)

3/4-

16UN

F

Ø1”

(25.

4 ±

0.08

)

Ø.406” (10.3 ± 0.05)1.71” (45)

.63” (16 ± 0.03)

.26” (6.6)/ .18” (4.6)

Ø1”

(25.

4)

1/4-20UNC-2BDeep 14.2 min

.22” (5.6)/ .14” (3.6)

.22” (5.6)/ .14” (3.6)

1.1” (28)

1.1”

(28)

Ø.9

8” (2

5)

1.97” (50)

.29” (7.4)/ .21” (5.4) M8x1.25-6H

Deep 16

1:8∇





MMRSW SeriesFeaturesMMRSW series wheel motors are spool valve motors that can be used in parallel or series configurations. A diverse offering of mounting flanges, shafts, ports, and displacements allow for easy installation, product replacement or OEM application.


� � Dual high efficiency tapered roller bearings, providing excellent low speed and high speed operation with high side load capabilities




MODEL CODE (DISPLACEMENT) 01 02 03 04 05 06 07 08 09 10 11

Displ.cm³/r 50 63 80 100 125 160 200 250 305 370 395

in³/r 3.1 3.8 4.9 6.1 7.6 9.8 12.2 15.3 18.6 22.6 24.1

Flow

LPMCont. 40 50 60 60 60 60 60 60 60 60 60

Int. 50 60 75 75 75 75 75 75 75 75 75

GPMCont. 10.6 13.2 15.9 15.9 15.9 15.9 15.9 15.9 15.9 15.9 15.9

Int. 13.2 15.9 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.8

Max Speed RPM

Cont. 775 760 750 600 475 375 300 240 190 160 150

Int. 970 950 940 750 600 470 375 300 240 200 185

Pressure

∆BarCont. 140 140 175 175 175 175 175 175 135 115 115

Int. 175 175 200 200 200 200 200 200 175 150 150

∆PSICont. 2031 2031 2538 2538 2538 2538 2538 2538 1958 1668 1668

Int. 2538 2538 2901 2901 2901 2901 2901 2901 2538 2176 2176

Torque

NMCont. 100 126 195 240 300 380 450 540 550 580 620

Int. 130 163 220 280 340 430 500 610 690 690 735

LBF-INCont. 885 1115 1726 2124 2655 3363 3983 4779 4868 5133 5487

Int. 1151 1443 1947 2478 3009 3806 4425 5399 6107 6107 6505

Specifications



Series

Displacement in³/r (cm³/r) 01 = 3.1 (50)02 = 3.8 (63)03 = 4.9 (80)04 = 6.1 (100)05 = 7.6 (125)06 = 9.8 (160)07 = 12.2 (200)08 = 15.3 (250)09 = 18.6 (305)10 = 22.6 (370)11 = 24.1 (395)

Flange & PilotA = 4-Bolt Wheel Flange, pilot Ø3.25” (82.5)



Drain Port1 = G 1/4 BSP2 = 7/16”-20UNF, O-ring3 = M14x1.54 = PT(RC) 1/4”5 = M10x1All motors come with a Steel Hex Socket Plugged Drain Port

PortsA = 7/8”-14UNF, O-ringB = G 1/2, BSP

MMRSW - 01 - A - 01 - D - 2 - B - A

Shafts01 = 1.38” (35mm) Tapered02 = 1.25” (31.75mm) Tapered03 = 1” (25.4mm) Tapered Shaft, with Woodruff Key and Nut04 = 1.25” (31.75mm) Straight, Keyed

MMRSW SeriesModel Code Breakdown



MMRSW SeriesPerformance InformationTo assure best motor life, run motor for approximately one hour at 30% of rated pressure before applying full load.Fill motor with equipment manufacturer’s recommended fluid prior to any load application and startup.

Side Load

Shaft Seal




28 55 69 97 110 124 138 155

FLOW

LP

M

7.6 18152

37147

46142

64134

72124

15.1 18298

37290

47276

66265

75261

84245

93243

22.7 17450

37438

47434

66419

75410

84407

93389

105373

30.3 14603

35590

44583

64584

74554

83545

92536

104520

37.9 14750

34738

44732

64713

73702

83696

92682

104661

45.4 43875

62859

72844

81835

91819

102804


28 55 69 97 110 124 138 155

FLOW

LP

M

7.6 22111

47107

59105

8096

9192

15.1 24229

50216

62212

87194

99190

110186

122183

22.7 22343

48334

60321

86319

99315

111291

123288

138276

30.3 21451

47442

60431

86419

98415

111412

123401

138386

37.9 18565

45552

58547

84532

97525

110512

122504

137496

45.4 18678

44665

57658

82641

95635

109623

121612

137601

53.0 42778

55771

81753

95746

107733

120723

135711

56.8 40832

53826

80806

93800

106786

119779

135766


28 55 69 97 110 124 138 155

FLOW

LP

M

7.6 3090

6183

7780

10670

11963

15.1 30185

62179

78175

109166

124162

140156

155150

22.7 29275

61267

77265

109253

124248

140240

155232

174221

30.3 27367

60359

76354

108343

124338

139333

155324

174313

37.9 26460

58450

74446

106435

122428

138420

153412

173399

45.4 24552

56543

72537

105523

121515

136509

152500

172487

53.0 54635

70630

102616

118609

134599

150592

170578

56.8 52680

69673

101660

117650

133642

149634

168619


28 55 69 97 110 124 138 155FL

OW

LPM

7.6 3971

7966

9883

13556

15251

17146

15.1 38146

79141

99138

139131

158128

177124

195118

22.7 37217

78211

98208

139199

158195

178190

196184

219174

30.3 36290

76284

97280

137217

157267

177262

195255

218245

37.9 33363

74355

95351

135343

155337

174332

193325

217315

45.4 31436

72429

92424

133414

153409

173402

192395

215384

53.0 27510

69501

90497

130487

150482

170475

189469

213456

56.8 67537

88532

128522

148516

168510

187502

211490


28 55 69 97 110 124 138

FLOW

LP

M

7.6 6145

12342

15340

20934

23530

26125

15.1 6195

12491

15590

21485

24282

26978

29573

22.7 59140

123136

155134

215129

243125

271121

297114

30.3 57187

121183

152181

213175

242172

270166

296259

37.9 53234

117230

149227

209222

239218

266211

293203

45.4 49282

114277

146274

206269

235265

263257

291248

53.0 45329

109323

141321

201316

230311

259304

287296

56.8 107347

139344

198339

228334

257327

284318


28 55 69 97 110 124 138 155

FLOW

LP

M

7.6 4856

9651

12150

16644

18940

21234

15.1 48114

95111

121110

166107

189105

21198

24090

22.7 47172

95171

120168

166157

188155

212151

240145

271130

30.3 46230

96225

120220

165216

187212

213206

239200

270190

37.9 45287

95283

120278

165272

185267

210260

237253

270240

45.4 44345

94341

118335

162328

183323

210317

235310

269300

53.0 38405

90401

115395

154390

180384

202378

228371

260358

56.8 82426

108424

143420

170415

195410

210404

245390

MMRSW SeriesPerformance Information

Continuous

Intermittent

27510

(Torque Nm)

(Speed RPM)




28 55 69 97 110 114 125 127

FLOW

LP

M

7.6 9429

18726

23024

30617

15.1 9562

19259

23559

31955

35950

36849

22.7 9391

19189

23688

32182

36178

37176

40172

41071

30.3 89122

187120

233119

319113

359108

369106

399101

40899

37.9 84152

182150

288148

313143

356136

366134

396127

406125

45.4 78183

175180

222179

309173

351166

361166

392156

402153

53.0 71213

169211

216209

302202

345195

356193

386185

397182

56.8 165226

212224

298217

341209

352207

383200

394197


28 41 55 69 83 97 103 110

FLOW

LP

M

7.6 11723

17622

23021

28319

32916

36611

15.1 11949

18048

23748

28947

34247

39144

41641

22.7 11674

17872

23772

29071

34269

39164

41762

44160

30.3 11098

17297

23297

28596

33994

39089

41486

43883

37.9 105122

166121

226120

280120

334117

385112

410108

435104

45.4 98146

159145

216145

271145

326142

379136

404131

428127

53.0 89171

151170

209170

264169

318165

371159

397154

423150

56.8 204182

258181

313177

366171

393165

419160


14 28 41 55 69 83 90FL

OW

LPM

7.6 6720

14019

21018

27217

33415

15.1 6641

14341

21540

28340

34239

40238

43037

22.7 6561

14160

21460

28359

34258

40057

42856

30.3 5682

13181

20680

27779

33678

39777

42777

37.9 50102

126102

199101

270101

331100

39397

42496

45.4 38122

120121

191120

255119

318119

383118

416116

53.0 26142

108141

182140

249139

310138

375137

408134

56.8 242150

303149

370147

403146


14 28 41 55 69 83 90

FLOW

LP

M

7.6 7118

15017

22417

29016

35614

15.1 7038

15238

22937

30237

36536

42936

45835

22.7 6957

15057

22857

30255

38554

42753

45652

30.3 6277

14076

22075

29574

35873

42372

45572

37.9 5396

13496

21295

28895

35394

41991

45290

45.4 40114

129113

204112

272111

339111

408110

444108

53.0 28133

115132

194131

267130

330129

400128

435125

56.8 258141

323140

394138

430137

MMRSW SeriesPerformance Information Cont.

Continuous

Intermittent

26142

(Torque Nm)

(Speed RPM)


28 55 69 97 110 124 138

FLOW

LP

M

7.6 7636

15233

18731

25325

28320

15.1 7677

15473

19173

25968

29265

32461

35555

22.7 74113

154110

192109

263104

294100

32895

35987

30.3 72151

150148

189146

260142

293139

326132

359123

37.9 67189

146186

185184

255181

290176

323166

355156

45.4 62228

142224

182222

251219

286213

320204

353192

53.0 56266

137261

176259

246256

291251

315242

348229

56.8 133281

172279

242275

278269

313260

346247







Case Drain Port:G1/4” (BSP)or 7/16-20UNF-2B O-ringor M14x1.5-6H

7/8-14UNF-2BO-ring or G1

Shaft

MMRSW SeriesDimensions - Aligned Ports

Port Thread Versions


XInches .35 .45 .57 ,71 ,90 1.14 1.40 1.76 2.21 2.67 2.84

Millimeters (9) (11.5) (14.4) (18.1) (22.8) (29.0) (35.6) (44.7) (56.0) (68.0) (72.0)

YInches 4.70 4.80 4.91 5.05 5.24 5.48 5.74 6.10 6.55 7.02 7.18

Millimeters (119.3) (121.8) (124.7) (128.3) (133.1) (139.1) (145.9) (154.9) (166.3) (178.3) (182.3)

Ø3.

25 (8

2.55

)

Ø2.

76 (7

0)

Ø1.

38 (3

5)

Ø3.

94 (1

00)

Ø5.

00 (1

27)

1 (2

5.4)

1 (2

5.4)

X(Displ. Width)

Port BPort A

Y

.29 (7.3)

.66

(16.

7) m

in

.59

(15)

min

.13 (3.3)

15°

.75 (19)

1.85 (47) ± 0.1

.94 (24) ± 0.1 G1/2”

0.875-14UNF-2B

1.45 (37)

A = 7/8”-14UNF, O-ring B = G1/2, BSP




MMRSW SeriesMounting Flanges

45°

5.20

” (13

2)

Ø5.81” (147.6)

4- Ø.53” (13.5)5.20” (132)

A = 4-Bolt Wheel Flange, Pilot 3.25” (82.6)




MMRSW SeriesShafts

1 = 1.38” (35mm) Tapered, Flat Key 6x6x20

2 = 1.25” (31.75mm) Tapered, Flat Key 7.96x7.96x32

Ø.16” (4)

.5” (12.7)

.20” (5)1:8∇

.31” (7.9)

.67” (17)

1.39” (35.4)

1.26” (32)

Ø1.

25” (

31.7

5)

1-20

UNEF

2.28” (58)

1.42” (36).79” (20) .51” (13)

.16” (4)

Ø.18” (4.5)

.24” (6)

.75” (19)

Ø1.38” (35)M

20x1

.5

1.73

” (44

)1:10∇





MMH SeriesFeaturesMMH series motors are spool valve motors that can be used in parallel or series configurations. A diverse offering of mounting flanges, shafts, ports, and displacements allow for easy installation, product replacement or OEM application.


� � Dual needle bearings provide high side load capacity with extended operating life




MODEL CODE (DISPLACEMENT) 01 02 03 04 05 06 07

Displ.cm³/r 200 245 310 390 490 630 800

in³/r 12.2 15.0 18.9 23.8 29.9 38.4 48.8

Flow

LPMCont. 80 80 80 80 80 80 80

Int. 100 100 100 100 100 100 100

GPMCont. 21.1 21.1 21.1 21.1 21.1 21.1 21.1

Int. 26.4 26.4 26.4 26.4 26.4 26.4 26.4

Max Speed RPM

Cont. 360 320 250 200 156 120 100

Int. 470 390 300 240 200 150 120

Pressure

∆BarCont. 175 175 175 155 125 125 100

Int. 200 200 200 190 150 150 120

∆PSICont. 2538 2538 2538 2248 1813 1813 1450

Int. 2901 2901 2901 2756 2176 2176 1740

Torque

NMCont. 500 614 777 866 877 1128 1146

Int. 573 700 888 1061 1053 1350 1375

LBF-INCont. 4425 5434 6877 7665 7762 9984 10143

Int. 5071 6196 7859 9391 9320 11949 12170

Specifications



Series

Displacement cm³/r (in³/r) 01 = 12.2 (200)02 = 15.0 (245)03 = 18.9 (310)04 = 23.8 (390)05 = 29.9 (490)06 = 38.4 (630)07 = 48.8 (800)

Flange & PilotA = 4-Bolt SAE “A” Magneto Flange, pilot Ø3.25” (82.5)B = 6-Bolt SAE “A” Magneto Flange, pilot Ø3.25” (82.5)



Drain Port1 = G 1/4 BSP2 = M14x1.53 = 7/16”-20UNF, O-ring4 = PT(RC) 1/4”All motors come with a Steel Hex Socket Plugged Drain Port

PortsA = 7/8”-14UNF, O-ringB = 1/2”-14NPTFC = G 1/2, BSPD = 3/4”-16UNF, O-ringE = M18x1.5F = M20x1.5G = M22x1.5H = PT(RC) 1/2”

MMH - 01 - A - 01 - D - 2 - B - A

Shafts01 = 1.26” (32mm) Straight, Flat key 10 x 8 x 4502 = 1.38” (35mm) Straight, Flat key 10 x 8 x 4503 = 1.25” (31.75mm) Straight, Flat key 7.96 x 7.96 x 3204 = 1” (25.4mm) SAE 6B Splined05 = 1.25” (31.75mm) 14t Splined M8 “European Standard”06 = 1.25” (31.75mm) 14t Splined 3/8” - 16 “US Standard”07 = 1.38” (35mm) Tapered Shaft, Flat key 6 x 6 x 20

MMH SeriesModel Code Breakdown



MMH SeriesPerformance InformationTo assure best motor life, run motor for approximately one hour at 30% of rated pressure before applying full load.Fill motor with equipment manufacturer’s recommended fluid prior to any load application and startup.

Side Load

Shaft Seal




35 70 105 140 175 200

FLOW

LP

M

20 13862

27659

41558

55352

69142

30 13893

27689

41587

55377

69163

79048

40 138124

276119

415116

553103

69184

79065

50 140155

280148

420145

560129

700105

80081

60 138186

276178

415174

553155

691126

79097

70 136217

273208

409203

546181

682147

780113

75 136232

273223

409218

546194

682157

780121

80 136248

273237

409232

546206

682168

90 136279

273267

409261

546232

682189


35 70 105 125 160

FLOW

LP

M

20 21839

43738

65537

78033

30 21859

43756

65555

78049

99940

40 21878

43775

65573

78065

99953

50 22198

44294

66492

79082

101166

60 218118

437113

655110

78098

99980

70 216137

431131

647129

771114

98693

75 216147

431141

647138

771122

98699

80 216157

431150

647147

771131

90 216176

431169

647165

771147


35 70 105 140 175 200

FLOW

LP

M

10 8948

17846

26845

35740

44633

20 8996

17892

26890

35680

44565

51050

30 89144

178138

268135

358120

44298

50975

40 89192

179184

268180

354160

440130

508100

50 89240

181230

268225

357200

439163

508125

60 89288

180276

268270

355240

438195

508150

70 89336

179322

268315

356280

437228

509175

75 89360

178345

267338

358300

436244

507188

80 89384

176368

264360

357320

435260

90 89432

175414

261405

352360

436293

Continuous

Intermittent

172185


35 70 105 140 155 190

FLOW

LP

M

20 17449

34847

52246

69641

77033

30 17474

34871

52269

69662

77050

94438

40 17498

34894

52292

69682

77067

94451

50 176123

352118

528115

704103

78083

95664

60 174148

348142

522138

696123

770100

94477

70 172172

343165

515162

687144

760117

93290

75 172185

343177

515173

687154

760125

93296

80 172197

343189

515185

687164

760133

90 172222

343212

515208

687185

760150


35 70 105 125 150

FLOW

LP

M

20 28130

56229

84329

100325

30 28146

56244

84343

100338

120431

40 28161

56258

84357

100351

120441

50 28476

56973

85371

101663

121952

60 28191

56288

84386

100376

120462

70 277107

555102

832100

99189

118972

75 277114

555110

832107

99195

118977

80 277122

555117

832114

991102

90 277137

555131

832129

991114

(Torque Nm)

(Speed RPM)

MMH SeriesPerformance Information


35 70 105 140 175 200

FLOW

LP

M

10 10939

21838

32837

43733

54627

20 10978

21875

32873

43765

54653

62441

30 109118

218113

328110

43798

54680

62461

40 111157

221150

332147

442131

553106

63282

50 109196

218188

328184

437163

546133

624102

60 108235

216225

324220

431196

539159

616122

70 108274

216263

324257

431229

539186

616143

75 108294

216282

324276

431245

539199

616153

80 108313

216300

324294

431261

539212

90 108353

216338

324331

431294

539239







Case Drain Port:G1/4” (BSP)or 7/16-20 O-ringor M14x1.5or PT(RC) 1/2

MMH SeriesDimensions - Staggered Ports

DISPLACEMENT CM³/R 200 245 310 390 490 630 800

XInches .88 1.08 1.36 1.71 2.15 2.73 3.51

Millimeters (22.4) (27.4) (34.6) (43.4) (54.5) (69.2) (89.1)

YInches 6.77 6.98 7.27 7.61 8.05 8.63 9.41

Millimeters (172) (177.4) (184.6) (193.4) (204.5) (219.2) (239.1)

Ø4.

84 (1

23)

2.83

(72)

.71

(18)

± 0

.2.7

1 (1

8) ±

0.2

X(Displ. Width)

PORT

7/8-14UNF O-ring M18x1.5

1/2-14NPTF M20x1.5

G1/2 (BSP) M22x1.5

3/4-16 O-ring PT1/2

CASE DRAIN PORT

G1/4

M14x1.5

7/16-20UNF

PT(RC) 1/2

None

Shaft

Port B

Port A

Y

.79 (20) ± 0.2.79 (20) ± 0.2

.24 (6).63 (16)

.79 (20) ± 0.2 .79 (20) ± 0.24-M8Deep 13 Min

45°

1.83 (46.5) 1.42 (36)

1.80 (45.7)




MMH SeriesMounting Flanges

45°

5.18

” (13

1.5)

max

2.09

” (53

.2) ±

0.1

52.

09” (

53.2

) ± 0

.15

2.44” (62) ± 0.2

4- Ø.53” (13.5)

A = 4-Bolt SAE “A”, Magneto Flange Pilot 3.25” (82.5) B = 6-Bolt SAE “A”, Magneto Flange Pilot 3.25” (82.5)


45°

5.35

” (13

6) m

ax

2.09

” (53

.2) ±

0.1

52.

09” (

53.2

) ± 0

.15

2.44” (62) ± 0.2

4- Ø.53” (13.5)



MMH SeriesShafts

1 = 1.26” (32mm) Straight, Flat Key 10x8x45 5 = 1.25” (31.75mm) 14t Splined, M8

3 = 1.25” (31.75mm) Straight, Flat Key 7.96x7.96x32 7 = 1.38” (35mm) Tapered, Flat Key 6x6x20

2 = 1.38” (35mm) Straight, Flat Key 10x8x45 6 = 1.25” (31.75mm) 14t Splined, 3/8”-16

4 = 1” (25.4mm) SAE, 6B Splined

2.28” (58)

1.42” (36).79” (20) .51” (13)

.16” (4)

Ø.18” (4.5)

.24” (6)

.75” (19)

Ø1.38” (35)

M20

x1.5

1.73

” (44

)

1:10∇

2.68” (68) max

2.17” (55 ± 0.3)

.79” (20)

.20” (5).39” (10)

1.38” (35)

1.77” (45)Ø

1.26

” (32

)

M8

2.68” (68) max

2.17” (55 ± 0.3)

.79” (20)

.20” (5).39” (10)

1.50” (38)

1.77” (45)

Ø1.

38” (

35)

M8

2.18” (55.3) max

1.57” (40)

.59” (15)

.25” (6-6.25 ± 0.05)

Ø.85” (21.47 ± 0.07)

1.04” (26.4)

Ø1”

(25.

4)

M8

2.18” (55.3) max

1.81” (46 ± 0.3)

.79” (20)

.20” (5).31” (8)

1.38” (35)

1.26” (32)

Ø1.

25” (

31.7

5)

3/8-

16UN

C

1.81” (46)

.79” (20)

1.30” (33)

Ø1.

25” (

31.7

5)

M8

1.89” (48)

.79” (20)

1.30” (33)

Ø1.

25” (

31.7

5)

3/8-

16UN

C





MMW SeriesFeaturesMMH series motors are spool valve motors that can be used in parallel or series configurations. A diverse offering of mounting flanges, shafts, ports, and displacements allow for easy installation, product replacement or OEM application.


� � Dual needle bearings provide high side load capacity with extended operating life





Displ.cm³/r 200 245 310 390 490 630 800

in³/r 12.2 15.0 18.9 23.8 29.9 38.4 48.8

Flow

LPMCont. 80 80 80 80 80 80 80

Int. 100 100 100 100 100 100 100

GPMCont. 21.1 21.1 21.1 21.1 21.1 21.1 21.1

Int. 26.4 26.4 26.4 26.4 26.4 26.4 26.4

Max Speed RPM

Cont. 360 320 250 200 156 120 100

Int. 470 390 300 240 200 150 120

Pressure

∆BarCont. 175 175 175 155 125 125 100

Int. 200 200 200 190 150 150 120

∆PSICont. 2538 2538 2538 2248 1813 1813 1450

Int. 2901 2901 2901 2756 2176 2176 1740

Torque

NMCont. 500 614 777 866 877 1128 1146

Int. 573 700 888 1061 1053 1350 1375

LBF-INCont. 4425 5434 6877 7665 7762 9984 10143

Int. 5071 6196 7859 9391 9320 11949 12170

Specifications



Series

Displacement cm³/r (in³/r) 01 = 12.2 (200)02 = 15.0 (245)03 = 18.9 (310)04 = 23.8 (390)05 = 29.9 (490)06 = 38.4 (630)07 = 48.8 (800)

Flange & PilotA = 4-Bolt Wheel Flange, pilot Ø3.25” (82.5)

PaintA = No PaintB = BlackC = Blue (Standard)Options A & B (or any other color needed) will only be considered for Large Quantity Orders

Rotation0 = Standard (Clock-wise)1 = Opposite (Counter Clock-wise)

Drain PortA = 7/16”-20UNF, O-ringB = G 1/4 BSPAll motors come with a Steel Hex Socket Plugged Drain Port

PortsA = 7/8”-14UNF, O-ringB = G 1/2, BSP

MMW - 01 - A - 01 - A - A - C - 0

Shafts01 = 1.25” (31.75mm) Tapered, Flat key 7.96 x 7.96 x 2202 = 1.25” (31.75mm) Straight, Flat key 7.96 x 7.96 x 3503 = 1.26” (32mm) Straight, Flat key 9.98 x 7.99 x 4504 = 1.25” (31.75mm) 14t Splined

MMW SeriesModel Code Breakdown



MMW SeriesPerformance InformationTo assure best motor life, run motor for approximately one hour at 30% of rated pressure before applying full load.Fill motor with equipment manufacturer’s recommended fluid prior to any load application and startup.

Side Load

Shaft Seal




35 70 105 140 175 200

FLOW

LP

M

20 13862

27659

41558

55352

69142

30 13893

27689

41587

55377

69163

79048

40 138124

276119

415116

553103

69184

79065

50 140155

280148

420145

560129

700105

80081

60 138186

276178

415174

553155

691126

79097

70 136217

273208

409203

546181

682147

780113

75 136232

273223

409218

546194

682157

780121

80 136248

273237

409232

546206

682168

90 136279

273267

409261

546232

682189


35 70 105 125 160

FLOW

LP

M

20 21839

43738

65537

78033

30 21859

43756

65555

78049

99940

40 21878

43775

65573

78065

99953

50 22198

44294

66492

79082

101166

60 218118

437113

655110

78098

99980

70 216137

431131

647129

771114

98693

75 216147

431141

647138

771122

98699

80 216157

431150

647147

771131

90 216176

431169

647165

771147


35 70 105 140 175 200

FLOW

LP

M

10 8948

17846

26845

35740

44633

20 8996

17892

26890

35680

44565

51050

30 89144

178138

268135

358120

44298

50975

40 89192

179184

268180

354160

440130

508100

50 89240

181230

268225

357200

439163

508125

60 89288

180276

268270

355240

438195

508150

70 89336

179322

268315

356280

437228

509175

75 89360

178345

267338

358300

436244

507188

80 89384

176368

264360

357320

435260

90 89432

175414

261405

352360

436293

Continuous

Intermittent

172185


35 70 105 140 155 190

FLOW

LP

M

20 17449

34847

52246

69641

77033

30 17474

34871

52269

69662

77050

94438

40 17498

34894

52292

69682

77067

94451

50 176123

352118

528115

704103

78083

95664

60 174148

348142

522138

696123

770100

94477

70 172172

343165

515162

687144

760117

93290

75 172185

343177

515173

687154

760125

93296

80 172197

343189

515185

687164

760133

90 172222

343212

515208

687185

760150


35 70 105 125 150

FLOW

LP

M

20 28130

56229

84329

100325

30 28146

56244

84343

100338

120431

40 28161

56258

84357

100351

120441

50 28476

56973

85371

101663

121952

60 28191

56288

84386

100376

120462

70 277107

555102

832100

99189

118972

75 277114

555110

832107

99195

118977

80 277122

555117

832114

991102

90 277137

555131

832129

991114

(Torque Nm)

(Speed RPM)

MMW SeriesPerformance Information


35 70 105 140 175 200

FLOW

LP

M

10 10939

21838

32837

43733

54627

20 10978

21875

32873

43765

54653

62441

30 109118

218113

328110

43798

54680

62461

40 111157

221150

332147

442131

553106

63282

50 109196

218188

328184

437163

546133

624102

60 108235

216225

324220

431196

539159

616122

70 108274

216263

324257

431229

539186

616143

75 108294

216282

324276

431245

539199

616153

80 108313

216300

324294

431261

539212

90 108353

216338

324331

431294

539239







Case Drain Port:G1/4” (BSP)or 7/16-20 O-ring

G1/2” (BSP)or 7/8-14UNF-2B SAE O-ring

MMW SeriesDimensions - Aligned Ports


XInches .88 1.08 1.36 1.71 2.15 2.73 3.51

Millimeters (22.4) (27.4) (34.6) (43.4) (54.5) (69.2) (89.1)

YInches 5.92 6.12 6.41 6.75 7.19 7.77 8.55

Millimeters (150.4) (155.5) (162.7) (171.5) (182.6) (197.3) (217.2)

Ø5.

00 (1

27)

1.81

(46)

.91

(23)

X(Displ. Width)

Shaft

Port BPort A

Y

1 (25.4).31 (8)

.35 (9)

Ø3.

25 (8

2.5)

1.80 (45.7) 2.03 (51.5)

2.56

(65)




MMW SeriesMounting Flanges

45°

5.20

” (13

2)

Ø5.81” (147.6)

4- Ø.53” (13.5)

5.20” (132)

A = 4-Bolt Wheel Flange, Pilot 3.25” (82.6)




MMW SeriesShafts

1 = 1.25” (31.75mm) Tapered, Flat Key 7.96x7.96x22

3 = 1.26” (32mm) Straight, Flat Key 9.98x7.99x45

2 = 1.25” (31.75mm) Straight, Flat Key 7.96x7.96x35

4 = 1.25” (31.75mm) 14t Splined

2.28” (58) ± 0.2

.79” (20)

.20” (5).39” (10)

1.38” (35)

1.77” (45)

Ø1.

26” (

32)

M8

Taper per Meter:125.0 ± 0.17/m

Recommended Torque:(373 Nm [275 lb-ft] Dry)(305 Nm [225 lb-ft] Lub)Plus torque required to align the slotted nut with shaft crosshole.

Ø.16” (4)

.5” (12.7)

.20” (5)1:8∇

.31” (7.9)

.67” (17)

2.40” (61)

.87” (22)Ø

1.25

” (31

.75)

1-20

UNEF

1.79” (45.5)

.79” (20)

1.30” (33)

Ø1.

25” (

31.7

5)

3/8-

16UN

C

1.87” (47.5)

.79” (20)

.31” (8)

1.39” (35.3)

1.28” (32.5)

Ø1.

25” (

31.7

5)

3/8-

16UN

C





MMS SeriesFeaturesMMS series motors are disc valve motors that can be used in parallel or series configurations. A diverse offering of mounting flanges, shafts, ports, and displacements along with wheel and bearingless motors allow for easy installation, product replacement or OEM application.


� � Disc valve technology, providing greater speed and efficiency for medium duty applications


� � High pressure shaft seal, which allows for higher back pressures and an increased ability to handle high pressure spike conditions (no shaft seal on bearingless motors)



MODEL CODE (DISPLACEMENT) 01 02 03 04 05 06 07 08 09

Displ.cm³/r 80 100 130 160 195 245 305 395 490

in³/r 4.9 6.1 7.9 9.8 11.9 15 18.6 24.1 29.9

Flow

LPMCont. 75 75 75 75 75 75 75 75 75

Int. 75 95 95 115 115 115 115 130 130

GPMCont. 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.8

Int. 19.8 25.1 25.1 30.4 30.4 30.4 30.4 34.3 34.3

Max Speed RPM

Cont. 799 742 576 477 385 308 246 191 153

Int. 908 924 720 713 577 462 365 335 230

Pressure

∆BarCont. 170 170 170 170 170 170 140 140 120

Int. 275 275 275 240 240 240 205 170 170

∆PSICont. 2466 2466 2466 2466 2466 2466 2031 2031 1740

Int. 3989 3989 3989 3481 3481 3481 2973 2466 2031

Torque

NMCont. 195 245 315 380 455 555 560 700 845

Int. 305 395 505 530 625 765 805 890 930

LBF-INCont. 1726 2168 2788 3363 4027 4912 4956 6196 7479

Int. 2700 3496 4470 4691 5532 6771 7125 7877 8231

Specifications



Series

Displacement in³/r (cm³/r) 01 = 4.9 (80)02 = 6.1 (100)03 = 7.9 (130)04 = 9.8 (160)05 = 11.9 (195)06 = 15.0 (245)07 = 18.6 (305)08 = 24.1 (395)09 = 29.9 (490)

Flange & PilotA = 4-Bolt SAE “B” Flange, pilot Ø3.94” (100)B = 2-Bolt SAE “A” Flange, pilot Ø3.25” (82.5)(Can be replaced by E)C = 4-Bolt SAE “A” Flange, pilot Ø3.25” (82.5) Eaton ‘Standard’D = 4-Bolt Wheel Flange, pilot Ø4.25” (107.9)E = 6-Bolt Magneto Flange, pilot Ø3.25” (82.5)(Can be replacement for B or G)F = 2-Bolt Rhomb Flange, pilot Ø3.15” (80)G = 4-Bolt Magneto Flange, pilot Ø3.25” (82.5)(Can be replaced by E)H = 2-Bolt SAE “B” Flange, pilot Ø4” (101.5)I = 4-Bolt Square Bearingless Flange

PaintA = No PaintB = Blue (Standard)C = BlackD = GreenOptions A, C & D (or any other color needed) will only be considered for Large Quantity Orders


Ports & Drain PortA = 7/8”-14UNF, O-ring & 7/16”-20UNF B = G 1/2, BSP & G 1/4 BSPC = M22 x 1.5 & M14 x 1.5(Manifold Mount 3-M10)D = G 1/2 & M14 x 1.5E = G 1/2 & G 1/4(Manifold Mount 2-M10)F = M14 x 1.5 & M14 x 1.5G = M22 x 1.5 & M10 x 1H = Not AvailableI = M20 x 1.5 & M14 x 1.5J = 1/2”-14NPTF & G 1/4K = 1-1/16”-12 O-ring (Positioned 180° apart) & 7/16”-20UNFL = End Port, 7/8”-14UNF, O-ring& 7/16”-20UNFM = End Port, G 1/2, BSP & G 1/4 BSPN = 12.70mm (.50”) & 15.88mm (.625”) & 7/16”-20UNF (Manifold Mount 3-3/8”)O = 12.70mm (.50”) & 15.88mm (.625”) & G 1/4 BSP (Manifold Mount 3-M10)P = 4-5/16”-18UNC (Manifold)Q = 4-M8x1.5 (Manifold)R = 2-Ø13 & M14x1.5-6HS = 2-Ø13 & 7/16”-20UNF, O-ringAll motors come with a Steel Hex Socket Plugged Drain Port

MMS - 01 - A - 01 - D - B - A

Shafts02 = .98” (25mm) Straight, Flat key 8mm04 = 1” (25.4mm) Straight, Woodruff key 6.35mm05 = 1.25” (31.75mm) Straight, Flat key 7.96mm06 = 1.25” (31.75mm) Tapered, Flat key 7.96mm07 = 1.25” (31.75mm) 14t, Splined09 = 1” (25.4mm) Straight, Flat key 6.35mm10 = 1.18” (30mm) Straight, Flat key 10mm11 = .87” (22mm) Straight, Flat key 6mm12 = 1.26” (32mm) Straight, Flat key 10mm13 = .98” (25mm) Straight, Flat key 8mm14 = 1” (25.4mm) SAE 6B Splined15 = .875” (22.2mm) SAE “B” 13t, Splined16 = Bearingless

MMS SeriesModel Code Breakdown



MMS SeriesPerformance InformationTo assure best motor life, run motor for approximately one hour at 30% of rated pressure before applying full load.Fill motor with equipment manufacturer’s recommended fluid prior to any load application and startup.

Side Load

Shaft Seal




35 70 105 140 170 205 240 275

FLOW

LP

M

0.95 253

451

1.90 3017

508

853

3.80 3544

7540

11037

14534

17528

20522

22014

2402

7.50 3590

7585

11081

15078

18072

21065

23557

26549

15.0 35182

75176

115170

150166

185159

215152

250140

280128

23.0 35273

75267

115259

150254

185246

225238

255223

290207

30.0 35365

75375

115349

150341

190333

230325

265306

300286

38.0 35456

75448

115439

155429

190420

230411

270388

305364

45.0 30547

70537

115530

155516

195507

235497

270470

305442

53.0 30638

70629

110622

150603

195593

235584

270553

305521

61.0 30729

70720

110714

150689

190679

230670

270635

305599

68.0 25818

65810

110795

150775

190765

230756

265717

300677

76.0 25908

65901

105880

145861

185851

225842

260799

295755

Continuous

Intermittent

185851

(Torque Nm)

(Speed RPM)

MMS SeriesPerformance Information


35 70 105 140 170 205 240 275

FLOW

LP

M

0.95 302

1.90 359

705

1052

3.80 4534

9531

13528

17523

21015

2406

7.50 4571

9568

14063

18059

21551

25038

28524

31514

15.0 45145

90141

140136

185131

225121

270104

31094

35580

23.0 45219

90215

140209

190202

235192

280172

325163

370149

30.0 40294

90288

140281

190273

240261

290243

340231

385216

38.0 40368

90362

145354

195344

245330

295316

340300

390283

45.0 40442

90436

145427

195415

245399

295389

345369

395350

53.0 35516

90509

140500

195486

245469

295463

345437

395417

61.0 35591

90583

140573

195558

245540

295537

345506

395485

68.0 35665

85657

140646

190630

240611

290609

340574

390552

76.0 30739

80731

135715

185703

235684

290662

335643

390619

83.0 30813

80805

135794

185777

235758

280749

330712

380687

91.0 30887

80879

130868

175852

230834

280814

330782

375754

95.0 25924

75916

125905

175890

225873

275846

325817







Continuous

Intermittent

MMS SeriesPerformance Information Cont.


15 35 70 105 140 170 205 240

FLOW

LP

M

0.95 253

1.90 259

557

1105

1753

2401

3.80 3023

6521

13019

19517

26013

3208

3753

4302

7.50 3546

7045

13542

20039

26535

33034

39533

46028

15.0 3593

7092

14089

21585

28579

36077

43075

50559

23.0 35142

75140

145137

220131

295124

370118

445113

520104

30.0 35190

75187

150184

225178

300170

375166

450164

525153

38.0 35237

70235

150231

230226

320217

385212

455205

530193

45.0 30286

70283

150279

230274

305265

380254

455246

530235

53.0 25334

65331

145326

230322

305312

380305

455297

530286

61.0 25382

65378

145374

225369

300360

375349

455339

530326

68.0 20429

60426

140422

220416

300407

375394

450387

76.0 20477

60474

135469

215462

300451

375440

445473

83.0 15525

55522

130517

210510

295501

370484

445473

91.0 15572

50569

130564

210556

290546

370531

440522

95.0 10596

50593

130587

210580

290566

265553

440544

114.0 35713

120706

200696

280682

355672

430658






35 70 105 140 170 205 240 275

FLOW

LP

M

0.95

1.90 458

1002

3.80 6027

12023

18019

23016

28513

3309

3753

7.50 6056

12053

18047

23542

29039

33036

37528

41021

15.0 55113

120111

185104

24597

30095

35092

40085

45077

23.0 55171

120169

185161

245153

310149

370146

425132

485118

30.0 55224

120222

185219

250210

315204

375201

435192

495184

38.0 55286

120282

185276

250269

315261

385255

445243

505231

45.0 50344

120338

185333

250327

315317

380307

440295

500284

53.0 50402

115395

185391

250385

340373

380360

440348

500336

61.0 45460

115452

180447

250443

315430

375411

440397

500384

68.0 45517

110509

180504

245500

310484

375471

435456

500440

76.0 45575

110568

175560

240551

305539

370524

435508

83.0 40633

105624

170619

235604

305597

365579

430560

91.0 35691

105682

170676

235665

300651

365633

425616

95.0 35719

100712

165705

230692

295679

360682

420656

240551

(Torque Nm)

(Speed RPM)



Continuous

Intermittent



15 35 70 105 140 170 205 240

FLOW

LP

M

0.95

1.90 454

952

3.80 5014

10513

21011

3159

4106

5154

6153

7151

7.50 5029

11028

21526

32523

42520

54018

64015

74012

15.0 5560

11559

22556

34053

45049

55547

66046

76544

23.0 5091

11590

23087

35083

46578

57073

67569

78065

30.0 50122

115121

235118

360113

475108

585104

690101

38.0 50153

115152

240148

360144

480139

560135

705103

45.0 45184

110183

235180

360175

480170

600165

53.0 40215

105214

235211

355207

480201

585195

61.0 40246

95245

230242

355238

470232

580223

68.0 30277

90276

225273

345269

465263

575253

76.0 30308

90306

215302

340298

465291

83.0 25339

80337

210334

330330

455323

91.0 15370

75369

200364

325360

445353

95.0 15385

75384

200379

325375

445367

114.0 60462

185458

305453

430447





75369

(Torque Nm)

(Speed RPM)


15 35 70 105 140 170 205 240

FLOW

LP

M

0.95 254

652

1.90 358

706

1502

3.80 4517

8016

16014

20011

3057

3704

4302

4901

7.50 4537

8535

16533

25031

32526

41521

51019

57514

15.0 4576

9074

17572

26070

34564

43061

51057

59551

23.0 45115

90113

180110

270108

360102

44599

53094

61587

30.0 45154

90151

185148

275146

370140

455135

540130

625123

38.0 45193

95190

185187

280184

375177

465173

545168

630160

45.0 40231

90229

185226

280221

375218

465211

550204

53.0 35269

85267

185264

280260

380254

465248

550241

61.0 30308

80306

185303

275296

375290

465283

550276

68.0 30346

80345

180342

270334

375327

465315

76.0 25385

75384

175380

270372

370367

460359

83.0 20424

70423

170418

265410

365404

460395

91.0 15462

65461

165457

260449

360441

450432

95.0 15484

60482

160476

260469

355459

445449

114.0 45577

145571

240562

330550



Continuous

Intermittent



15 35 70 105 120 140 155 170

FLOW

LP

M

0.95

1.90 654

1503

3.80 859

1759

3508

5057

5857

6656

7455

8204

7.50 9018

18018

36017

53016

61515

70014

77513

84511

15.0 9037

19037

37536

56035

65034

74033

81531

89028

23.0 9057

19056

38555

57552

67050

76549

84047

90545

30.0 9076

19075

39074

58071

67569

77068

38.0 9095

19094

39593

58590

68088

77586

45.0 85114

190113

390112

580109

675106

770103

53.0 85133

185132

390131

580127

675124

61.0 80153

180152

380150

570146

670144

68.0 70172

170171

375170

565167

665164

76.0 65191

165190

370189

560186

660184

83.0 60210

155209

360208

550206

91.0 50230

150229

350227

540224

98.0 40249

140248

340246

535242

114.0 20287

120286

320283

515277

132.0 95335

300333





350227

(Torque Nm)

(Speed RPM)


15 35 70 105 140 170 205

FLOW

LP

M

0.95

1.90 554

1202

3.80 7012

13511

26010

3909

5006

6101

7.50 7024

13524

27022

39520

52018

64015

76511

15.0 7549

14049

28047

41545

54542

67538

80534

23.0 7074

14574

29072

43069

56064

69558

82552

30.0 7098

14598

29596

44093

57586

70580

38.0 65123

140122

295120

440117

580110

720102

45.0 60148

140147

295144

440142

580133

720124

53.0 55172

135172

290168

440165

580156

61.0 50196

125196

280192

440188

575178

68.0 40221

120221

275217

440212

570202

76.0 35246

110245

265241

420236

565226

83.0 25271

105270

260266

400260

545255

91.0 20296

100294

255290

385285

525280

95.0 15308

95307

250303

375298

510293

114.0 75365

230360

355356



Continuous

Intermittent







15 35 50 70 85 105 120 140

FLOW

LP

M

1.90 752

1801

3.80 1057

2256

3405

4404

5502

7.50 10514

23513

35012

46010

5759

7157

15.0 11030

24029

36528

48027

60526

72024

83522

90020

23.0 11045

24044

36543

48542

60541

72539

84537

93035

30.0 11061

24060

36559

49058

61057

73055

85552

38.0 10576

23075

36074

48573

61072

73072

85568

45.0 9591

22590

35590

48089

60587

73085

85584

53.0 90106

220105

345105

475104

600102

725100

61.0 80122

210121

340120

465119

590118

715116

68.0 70153

190152

315151

445150

570149

700146

76.0 60153

190152

315151

445150

570149

700146

83.0 50168

175168

305167

435165

560164

685161

91.0 40184

165184

295183

420181

550179

675177

98.0 30199

155195

285195

410192

540190

106.0 140212

270211

400209

525207

114.0 125230

255229

385277

510224

285195

(Torque Nm)

(Speed RPM)



MMS SeriesDimensions - Staggered Ports

Case Drain Port:

Shaft

.25 (6.3) .86 (21.9)X

(Displ. Width)

Y

DISPLACEMENT CM³/R 80 100 130 160 195 245 305 395 490

XInches .57 .70 .89 1.14 1.40 1.76 2.20 2.83 3.52

Millimeters (14.4) (17.8) (22.5) (28.9) (35.6) (44.7) (56.0) (72.0) (89.3)

YInches 7.24 7.44 7.68 7.68 7.95 8.31 8.78 9.41 10.08

Millimeters (184) (189) (195) (195) (202) (211) (223) (239) (256)

2.13

” (54

) min

1.91 (48.6) max

2.37

(60.

2) m

ax

Port A

Port B




MMS SeriesDimensions - Wheel Mount (Flange D)

Ø1.

25 (3

1.7)

Ø3.

75 (9

5.2)

Ø4.

25 (1

07.9

)

.88 (22.3).25 (6.3)

.15

(3.7

9)1.00 (25.4) ± 0.5

.13 (3.3)

X(Displ. Width)

Y1.83 (46.5)2.23 (56.7)


XInches .57 .70 .89 1.14 1.40 1.76 2.20 2.83 3.52

Millimeters (14.4) (17.8) (22.5) (28.9) (35.6) (44.7) (56.0) (72.0) (89.3)

YInches 5.67 5.83 6.10 6.10 6.38 6.73 7.17 7.80 8.50

Millimeters (144) (148) (155) (155) (162) (171) (182) (198) (216)

2.13

” (54

) min

5.28

” (13

4.2)

max

5.28” (134.2) max

4- Ø.52” (13.3)Bolt Circle Ø5.81” (147.6)

Ø5”

(127

)




MMS SeriesDimensions - Bearingless (Flange I, Shaft Code 16)

.63 (16).25 (6.3)

4- Ø.54” (13.6)Bolt Circle Ø5.00” (127)Ø

4.00

(101

.5) ±

0.1

-0.0

3

4.69 (119.2)

X(Displ. Width)

Y

E

Dei

DDii

1.65 (42)

SHAFT CODE 16 - DIMENSIONS

Fillet Root Side Fit mm

Number of Teeth Z 12

Diametral Pitch DP 12/24

Pressure Angle D 30

Pitch Dia. D Ø25.4

Major DIa. Dei Ø28

Minor DIa. Dii Ø23

Space Width E 4.308


XInches .57 .70 .89 1.14 1.40 1.76 2.20 2.83 3.52

Millimeters (14.4) (17.8) (22.5) (28.9) (35.6) (44.7) (56.0) (72.0) (89.3)

YInches 5.00 5.16 5.43 5.43 5.71 6.06 6.50 7.13 7.80

Millimeters (127) (131) (138) (138) (145) (154) (165) (181) (198)




MMS SeriesMounting Flanges

45°

5.35

” (13

6) m

ax

4.72

” (12

0)

4.72” (120)

4.25”

(108) 4.25” (108)

4- Ø.51” (13)

Ø5” (127)

4- Ø.53” (13.5)

Pilot:Ø3.94” (100)

Ø3.25” (82.5)

Ø4.19”(106.35)

A = 4-Bolt SAE “B” Flange, Pilot 3.94” (100) B = 2-Bolt SAE “A” Flange, Pilot 3.25” (82.5)

C = 4-Bolt SAE “A” Flange, Pilot 3.25” (82.5) D = 4-Bolt Wheel Flange, Pilot 4.25” (107.9)

E = 6-Bolt Magneto Flange, Pilot 3.25” (82.5) F = 2-Bolt Rhomb Flange, Pilot 3.15” (80)

(For dimensions see page 47)

Pilot:Ø3.25” (82.5)

Bolt Circle:Ø4.19” (106.38)

5.12

” (13

0) m

ax

4.19

” (10

6.4)

2- Ø.53” (13.5)Pilot:Ø3.25” (82.5)

5.12

” (13

0) m

ax

4.29

” (10

9)

2- Ø.43” (11)Pilot:Ø3.15” (80)

6- Ø.53” (13.5)




MMS SeriesMounting Flanges Cont.

G = 4-Bolt Magneto Flange, Pilot 3.25” (82.5)

5.35

” (13

6) m

ax

4- Ø.53” (13.5)

22.5° 22.5°

Ø4.19” (106.4)

Pilot:Ø3.25” (82.5)

H = 2-Bolt SAE “B” Flange, Pilot 4” (101.5)

I = 4-Bolt Square Flange, Pilot 4” (101.5)6.

98” (

177.

3) m

ax

5.75

” (14

6.05

)

2- Ø.57” (14.5)Pilot:Ø4” (101.5)

Bearingless(For dimensions see page 48)




MMS SeriesShafts

1 = 1” (25.6mm) Square Splined, 6D 30x26x8 5 = 1.25” (31.75mm) Straight, Flat Key 7.96x7.96x32

3 = 1.02” (26mm) Square Splined, 6D 30x26x6 7 = 1.25” (31.75mm) 14t Splined

2 = .98” (25mm) Straight, Flat Key 8mm 6 = 1.25” (31.75mm) Tapered, Flat Key 7.96x7.96x32

4 = 1” (25.4mm) Straight, Woodruff Key 6.35mm 8 = 1” (25.4mm) Square Splined, 6D 25.4x21.5x6.25

1.69” (43)

1.87” (47.5)

1.5” (38)

2.17” (55.1)

.79” (20)

Ø.16” (4)

.5” (12.7)

.20” (5)1:8∇

1.24” (31.4)

.79” (20)

.97” (24.6) - 1.03” (26.2)

Ø1.

38” (

35)

Ø1.

25” (

31.7

5)

Ø1.

18” (

30)

Ø1.

25” (

31.7

5)

3/8-16UNC-2B

1-20

UNEF

1.89” (48)

1.26” (32)Ø

1.18

” (30

)

M8-6HDeep 20

Ø1”

(25.

6)

1.1” (28)

1.1”

(28)

Ø.9

8” (2

5)

2.05” (52) - 2.13” (54)

1.89” (48) M8-6HDeep 20

Ø1.

02” (

26)

M8-6HDeep 20

1.96” (49.7) - 2.06” (52.4)

1/4-20UNC-2B

.73” (18.5 ± 0.3)

Ø1”

(25.

4)

1.11

” (28

.2)

2.05” (52) - 2.13” (54)

4.04” (102.8) - 4.15” (105.5)

2.05” (52) - 2.13” (54)

1.30” (33) minØ1.03” (26.2)

Ø1.

24” (

31.4

)

1.87” (47.5)3/8-16UNC-2B

1.85” (47) - 1.93” (49)

1.51” (38.3)

1.04” (26.4)

Ø1”

(25.

4)

3/8-16UNC-2B




MMS SeriesShafts Cont.

9 = 1” (25.4mm) Straight, Flat Key 6.35mm 13 = .98” (25mm) Straight, Flat Key 8mm

11 = .87” (22mm) Straight, Flat Key 6mm 15 = .875” (22.2mm) SAE B, 13t Splined

10 = 1.18” (30mm) Straight, Flat Key 10mm 14 = 1” (25.4mm) SAE, 6B Splined

12 = 1.26” (32mm) Straight, Flat Key 10mm 16 = Bearingless

1.26” (32)

1.11

” (28

.2)

Ø1”

(25.

4)

1.73” (44) - 1.81” (46)

1.54” (39) M8-6HDeep 20

1.85” (47)

1.30

” (33

)

2.44” (62) - 2.52” (64)

2.24” (56.8) M8-6HDeep 20

Ø1.

18” (

30)

1.57” (40)

.96”

(24.

5)

2.48” (63) - 2.56” (65)

2.28” (58) M8-6HDeep 20

Ø.8

7” (2

2)

1.78” (45.3) - 1.80” (45.7)

1.38

” (35

)

2.50” (63.5) - 2.59” (65.8)

2.22” (56.4) M8-6HDeep 20

Ø1.

26” (

32)

1.23” (31.2) - 1.29” (32.8)

1.10

” (28

)

Ø.9

8” (2

5)

1.96” (49.7) - 2.06” (52.4)

1.51” (38.4) M8-6HDeep 20

1.96” (49.7) - 2.06” (52.4)

.91” (23)Ø.83” (21)

Ø1”

(25.

4)

1.13” (28.8)1/4-20UNC-2B

1.57” (39.8) - 1.66” (42.2)

1.26” (32)Ø.70” (17.8)

Ø.8

75” (

22.2

)

1.21” (30.8)

1.64” (41.6) - 1.68” (42.7)

Ø4”

(101

.5)

.25” (6.3 ± 0.3)

Ø1.

73” (

44)




MMS SeriesPort Dimensions

Multiple Options

F = M14x1.5 & M14x1.5 R = 2- Ø13 & M14x1.5-6H S = 2- Ø13 & 7/16”-20UNF, O-ring

C = M22x1.5 & M14x1.5 E = G1/2” & G1/4”

1.83” (46.58) .79” (20.07)1”

(25.

4)

.47”

(11.

94)

.45” (11.55)

1.87” (47.58) .71” (18.07)

.20” (5)

.20” (5).87” (22)

1.83” (46.58)1.83” (46.58)

M22x1.5-6HCase Drain: M14x1.5-6H

M14x1.5-6HCase Drain: M14x1.5-6H

G1/2”Case Drain: G1/4”

2- Ø13Case Drain: M14x1.5-6H2- Ø13Case Drain: 7/16”-20UNF, O-ring

3- M10x1.5-6HDeep 15.7

2- M10x1.5-6HDeep 13

0.875-14UNF-2B O-ringCase Drain: 0.4375-20UNF O-ringG1/2”Case Drain: G1/4”G1/2”Case Drain: M14x1.5-6HM22x1.5-6HCase Drain: M10x1-6HM20x1.5Case Drain: M14x1.5-6HNPTF 1/2”Case Drain: G1/4”

A =

B =

D =

G =

I =J =

1” (2

5.4)

1.4”

(35.

56)

2.56

” (65

.02)

1.04

” (26

.4)

.51” (12.94)

.79” (20.07)

1.4”

(35.

56)

.47”

(11.

94)

1” (2

5.4)

2.56

” (65

.02)

1.83” (46.58)

.63”

(16)

.83”

(21)

.63”

(16)

.83”

(21)

.47”

(11.

94)





MMK SeriesFeaturesMMK series motors are disc valve motors that can be used in parallel or series configurations. A diverse offering of mounting flanges, shafts, ports, and displacements along with wheel and bearingless motors allow for easy installation, product replacement or OEM application.







MODEL CODE (DISPLACEMENT) 01 02 03 04 05 06 07 08 09

Displ.cm³/r 110 130 160 205 245 310 395 495 625

in³/r 6.7 7.9 9.8 12.5 15.0 18.9 24.1 30.2 38.1

Flow

LPMCont. 75 95 95 95 95 95 95 95 95

Int. 95 115 115 115 130 130 150 150 150

GPMCont. 19.8 25.1 25.1 25.1 25.1 25.1 25.1 25.1 25.1

Int. 25.1 30.4 30.4 30.4 34.4 34.4 39.6 39.6 39.6

Max Speed RPM

Cont. 697 722 582 459 383 303 239 191 151

Int. 868 862 693 546 532 422 376 305 241

Pressure

∆BarCont. 205 205 205 205 205 205 190 140 115

Int. 310 310 310 310 260 260 240 170 140

∆PSICont. 2973 2973 2973 2973 2973 2973 2756 2031 1668

Int. 4496 4496 4496 4496 3771 3771 3481 2466 2031

Torque

NMCont. 320 375 485 600 705 850 930 945 970

Int. 470 560 705 800 845 1065 1185 1170 1180

LBF-INCont. 2832 3319 4293 5310 6240 7523 8231 8364 8585

Int. 4160 4956 6240 7081 7479 9426 10488 10355 10444

Specifications



Series

Displacement cm³/r (in³/r) 01 = 6.7 (110)02 = 7.9 (130)03 = 9.8 (160)04 = 12.5 (205)05 = 15.0 (245)06 = 18.9 (310)07 = 24.1 (395)08 = 30.2 (495)09 = 38.1 (625)

Flange & PilotA = 4-Bolt SAE “B”, pilot Ø4.00” (101.6)B = 4-Bolt SAE “C”, pilot Ø5.00” (127)C = 4-Bolt Wheel Flange, pilot Ø5.50” (139.7)D = 4-Bolt Bearingless, pilot Ø5.00” (127)E = 4-Bolt Flange, pilot Ø4.92” (125)F = 4-Bolt Bearingless, pilot Ø4.92” (125)

Seals0 = Buna (Standard)1 = Viton Shaft Seal & Buna Seals2 = Buna Shaft Seal & Viton Seals3 = Viton Shaft Seal & Viton Seals


Ports & Drain PortA = 1-1/16”-12UNF, O-ring & 7/16”-20UNF, O-ringB = G 3/4, BSP & G 1/4, BSPC = 4-Bolt Split Flange (to fit SAEJ518C2) & 7/16”-20UNF, O-ringD = 7/8”-14UNF, O-ring & 9/16”-18UNF, O-ringE = M22 x 1.5-6H & M12 x 1.5-6HAll motors come with a Steel Hex Socket Plugged Drain Port

MMK - 01 - A - 01 - A - 1 - 0 - A

Shafts01 = 1.25” (31.75mm) Straight, Flat key 7.96mm(Available with Code A, B & C Flange Only)02 = 1.25” (31.75mm) 14t, Splined(Available with Code A, B & C Flange Only)03 = 1.57” (40mm) Straight, Flat key 11.96mm(Available with Code A, B & C Flange Only)04 = 1.50” (38.1mm) 17t, Splined(Available with Code B Flange Only)05 = 1.625” (41.275mm) Tapered(Available with Code A & C Flanges Only)06 = Bearingless(Available with Code D Flange Only)

Paint0 = No Paint1 = Blue (Standard)2 = BlackOptions 0 & 2 (or any other color needed) will only be considered for Large Quantity Orders

MMK SeriesModel Code Breakdown



MMK SeriesPerformance InformationTo assure best motor life, run motor for approximately one hour at 30% of rated pressure before applying full load.Fill motor with equipment manufacturer’s recommended fluid prior to any load application and startup.

Side Load

Shaft Seal




15 35 70 105 140 170 205 240 275 310

FLOW

LP

M

1.90 1514

4510

955

1452

3.80 2034

5033

10031

15528

21025

25522

30518

35011

7.50 2068

5067

10562

15556

21050

26044

30536

35528

39018

15.0 20138

50136

105123

160110

21097

26084

31070

35556

40042

44028

23.0 25207

55204

110200

160193

210184

260174

310163

360150

410136

455121

30.0 20277

50274

105270

160262

210253

265241

315228

365213

415196

455179

38.0 20347

50344

105340

160331

215322

265308

320292

370274

420255

460236

45.0 20417

50414

105410

160400

210390

265374

320355

370335

420313

460292

53.0 15487

50484

105480

160469

210458

265440

320419

370446

420471

465348

61.0 15556

50553

105549

160537

210525

265505

320482

375455

425428

465404

68.0 10626

50622

105618

160606

210593

265570

320545

375516

425485

465460

76.0 10697

50694

100690

155677

210664

265638

320611

375579

430545

470518

95.0 45868

95861

155838

210816

260792

320767

375729

425690


15 35 70 105 140 170 205 240 275 310

FLOW

LP

M

1.90 3512

609

1205

1802

3.80 3530

6028

12025

18019

24014

30013

34512

3904

7.50 3057

6056

12553

18547

24042

30040

36038

40529

45520

46012

15.0 30116

60114

125111

185105

250100

30595

36590

41570

46550

51537

23.0 25173

60170

125167

185161

250156

305149

365142

420123

470104

52591

30.0 25228

60225

120222

185216

250210

310202

370194

425176

480158

535145

38.0 25283

60281

120278

185272

250266

310256

375246

430229

490212

545189

45.0 25341

55338

120335

185329

250323

310312

375300

435282

495263

550237

53.0 20400

55396

120392

185386

250380

310368

375355

435335

495315

550286

61.0 20457

55453

120449

185443

250437

310424

375410

435388

495366

555335

68.0 15516

55511

120506

185500

250494

310480

375465

435442

500418

560384

76.0 10574

55569

120564

185559

250551

310536

375520

440495

500470

83.0 10633

50628

115624

180615

245606

310590

375573

440547

500520

95.0 5722

50718

115714

180702

245690

305672

375653

435625

500595

114.0 45862

105855

170842

235827

300806

360783

425749160 cc/r

∆ PRESSURE BAR15 35 70 105 140 170 205 240 275 310

FLOW

LP

M

1.90 358

757

1505

2303

3101

3.80 3523

8022

15520

23519

31518

37516

44515

5008

5602

7.50 3546

8045

15541

23540

31537

37532

45029

51027

57525

63013

15.0 3593

8092

16090

24088

32084

38576

45573

52062

59051

64535

23.0 35137

80135

160134

240131

320126

395120

470114

54090

60575

66557

30.0 30184

80182

165180

245176

330171

400163

480154

550138

620122

680100

38.0 30232

80229

165226

250221

335216

410206

485194

555182

630169

695142

45.0 25277

80274

165272

245266

330260

405250

485238

555224

630209

700182

53.0 25321

75319

160318

245311

325304

405294

480282

555266

630249

700222

61.0 25366

75364

160362

240356

325348

400338

480326

555308

630289

705262

68.0 20410

75409

155407

235401

320392

400382

480370

555350

635329

705302

76.0 15460

70458

150456

235448

315440

395429

480417

555396

635373

83.0 15509

70506

150502

235494

315484

396473

475461

555438

635413

95.0 10582

70578

150573

230563

315552

395540

475526

555501

630474

114.0 65693

145687

225675

305661

390647

450630

525600

Continuous

Intermittent

245690

(Torque Nm)

(Speed RPM)

MMK SeriesPerformance Information








15 35 70 105 140 170 205 240 275 310

FLOW

LP

M

1.90 458

905

1701

3.80 4517

9517

18016

25015

32514

43512

51511

6109

6253

7.50 4536

9535

19034

27032

35529

46027

54025

61022

68016

7008

15.0 5073

10073

20071

29570

38568

48061

57057

64545

71535

76023

23.0 50107

100106

205105

295103

400101

49598

58590

66581

74574

80065

30.0 45144

100143

205142

300138

400136

500132

590125

680116

765109

38.0 45182

95180

205179

305174

405170

505166

600160

690152

780143

45.0 40217

95216

205215

305211

405202

500200

600194

690185

53.0 35256

95254

200252

300248

400243

500237

600229

690219

61.0 35291

95290

200289

300284

400280

500272

595264

690253

68.0 30329

90327

200325

300321

400316

495308

595298

690287

76.0 25366

90364

195362

295358

395353

495345

595334

690321

83.0 20402

90400

190398

295394

395389

495380

595368

95.0 15459

85456

185453

290448

395442

495434

590421

114.0 80546

175542

285537

380529

475520

570504


15 35 50 70 85 105 120 140 155 170 190 205 225 240 260

FLOW

LP

M

1.90 505

1102

3.80 5514

11014

17014

22513

28013

33512

38512

43511

48011

53010

5654

7.50 5530

11530

17029

23029

28528

34527

38526

44524

50023

55522

60020

65018

69516

75014

81011

15.0 6061

11561

17560

23560

29559

35559

41058

46556

52553

58049

63047

68044

73042

77539

83036

23.0 6091

12090

17590

23589

29588

35588

41586

47583

53080

59075

64572

69570

75067

79563

84059

30.0 55121

115121

175120

240119

295118

355117

415115

475113

535111

595106

645103

70099

75596

80091

84587

38.0 55152

115151

175150

235148

295148

355147

415145

480143

540141

600137

650133

705129

760125

805120

45.0 50183

110182

175180

235179

295178

355178

415176

475173

540170

595166

650161

705157

755152

53.0 45213

110212

170211

235210

295209

355208

415206

475203

535200

595195

650190

705185

61.0 45244

105243

170242

230241

290240

355239

415236

475232

535229

595225

650219

705213

68.0 45275

105274

165273

230272

290270

350269

415266

470262

530269

590254

645248

700241

76.0 40305

105305

165304

225303

290302

350300

410296

470292

530288

590283

645276

83.0 36337

100336

160335

225334

280332

345330

405326

465323

530319

590313

640306

95.0 30383

95382

155381

220380

280378

335376

400372

460369

525365

585357

114.0 75457

140456

210455

270453

330450

390445

445442

505437

560427

132.0 125532

195531

255528

315525

375519

440515

495509

Continuous

Intermittent

54025

(Torque Nm)

(Speed RPM)

MMK SeriesPerformance Information Cont.



Continuous

Intermittent



15 35 50 70 85 105 120 140 155 170 190 205 225 240 260

FLOW

LP

M

1.90 704

1302

3.80 7011

14511

21511

29010

36010

42510

4859

5559

6209

6858

7558

8207

8907

9606

10255

7.50 7023

14523

22022

29522

36521

43521

50520

57520

64019

71018

78018

85017

92017

99516

106515

15.0 7047

14547

22046

30046

37045

44545

52044

59044

66543

73542

81042

88041

95541

103040

23.0 7571

14571

22570

30070

37569

45069

53068

60067

67566

75064

82564

89563

30.0 7096

14596

22595

30095

38094

45594

53093

60592

68091

75589

82589

38.0 70121

145120

225120

300119

375119

460118

535117

610116

685115

760112

835109

45.0 70145

140144

220144

295143

375142

455142

535141

610140

685139

760135

53.0 65169

140169

215168

295168

375167

450167

530165

610164

685163

760159

61.0 60193

140193

215192

290192

370190

450189

530188

610187

685185

68.0 55217

135217

210216

290216

365214

445213

530211

605209

680207

76.0 50242

135242

210242

285241

365240

440238

530236

605234

680232

83.0 45267

130266

205266

285265

360264

440262

525260

600258

95.0 40303

120303

200302

285301

355300

430299

520296

595293

114.0 115363

190362

275360

350359

420358

510354

580351

132.0 180422

265420

335419

400418

495413


15 35 50 70 85 105 120 140 155 170 190 205 225 240

FLOW

LP

M

1.90 804

1502

3.80 859

1609

2408

3158

3908

4707

5507

6357

7155

7904

8702

7.50 9018

17018

26017

34016

43516

52015

60015

68014

76513

84513

93012

101511

110010

11858

15.0 9538

18538

28037

37536

46536

55535

63535

72034

81034

89033

99032

23.0 9557

19057

28556

38555

47054

56553

65552

74550

83549

93047

30.0 9576

19076

29075

38574

48073

57572

66570

75068

84566

38.0 9095

19095

29094

38593

48092

57591

67089

76086

85584

45.0 85114

190114

285113

380112

480111

575110

665108

755105

53.0 85133

185133

280132

380131

480130

575129

665127

750124

61.0 80153

185153

280152

380151

480149

575147

660145

68.0 75172

180172

275171

375170

475168

570166

655164

76.0 70192

180191

270190

375189

475187

570185

655183

83.0 65211

170210

265209

365208

470206

565204

650201

95.0 55239

155238

255237

350236

460235

560233

645230

114.0 120285

185284

255282

340281

435279

132.0 170331

240330

325328

425325

151.0 230376

315374

410371

85017

(Torque Nm)

(Speed RPM)



Continuous

Intermittent



15 35 50 70 85 105 120 140 155 170

FLOW

LP

M

1.90 903

2001

3.80 1007

2106

3256

4305

5404

6453

7552

8601

7.50 10018

22017

33517

45016

56515

68012

79011

90510

10158

15.0 10530

22529

34528

47027

59526

71023

83021

94519

106017

117014

23.0 10545

22544

35043

47542

59540

71537

84035

95532

107030

30.0 10061

23060

35559

47557

60055

72052

84549

96046

38.0 10076

22575

35074

47572

60070

72066

84563

96059

45.0 9591

22590

35089

47587

60085

72081

84577

53.0 95106

220105

345104

470102

595100

72096

84092

61.0 90122

215120

340119

465117

595115

715111

840107

68.0 85137

210136

335134

465132

590130

715125

835121

76.0 75153

205152

330150

460147

590145

710140

95.0 65191

190189

315187

455184

590182

695177

114.0 170228

300226

425223

550220

675215

132.0 270265

395263

151.0 245305

370303


15 35 50 70 85 105 110 115 125 140

FLOW

LP

M

1.90 1152

3.80 1205

2655

4055

5504

6904

8303

8853

9352

9902

7.50 12514

27014

41514

56513

71512

86011

91510

9709

10308

11407

15.0 12523

27523

42523

58522

74521

89519

95018

101517

108516

118014

23.0 12535

28035

43035

59034

75033

90031

95030

100529

107028

30.0 12548

28048

44047

59546

75045

90543

95543

101042

38.0 13060

29060

45059

60058

75557

91054

97053

103552

45.0 13072

29572

46071

60570

75569

91565

98064

53.0 12584

28584

45083

60082

75581

91077

97576

61.0 12096

28095

44095

59594

75593

91089

97088

68.0 110108

270107

430107

590105

750104

830100

76.0 105121

265120

425120

590118

750116

95.0 85151

245150

405149

565147

725146

114.0 60181

225180

385179

530177

700176

132.0 355210

515208

151.0 320241

485239

79011

(Torque Nm)

(Speed RPM)







Case Drain Port

Port B

Port A

1.14

(28.

9)

1.16 (29.5)

Y1

Shaft

Y2

MMK SeriesDimensions - Configuration Flange A


XInches .57 .67 .83 1.06 1.26 1.60 2.03 2.54 3.20

Millimeters (14.4) (17.1) (21.1) (26.8) (32.1) (40.6) (51.5) (64.5) (81.4)

Y1Inches 6.02 6.14 6.30 6.54 6.73 7.09 7.48 7.99 8.66

Millimeters (153) (156) (160) (166) (171) (180) (190) (203) (220)

Y2Inches 8.23 8.35 8.50 8.74 8.94 9.29 9.69 10.20 10.86

Millimeters (209) (212) (216) (222) (227) (236) (246) (259) (276)

X(Displ. Width)




Case Drain Port

Port B

Port A

1.14

(28.

9)

1.16 (29.5)

Y1

Shaft

Y2

MMK SeriesDimensions - Configuration Flange B


XInches .57 .67 .83 1.06 1.26 1.60 2.03 2.54 3.20

Millimeters (14.4) (17.1) (21.1) (26.8) (32.1) (40.6) (51.5) (64.5) (81.4)

Y1Inches 6.22 6.30 6.46 6.69 6.89 7.24 7.64 8.15 9.21

Millimeters (158) (160) (164) (170) (175) (184) (194) (207) (224)

Y2Inches 8.43 8.50 8.66 8.90 9.09 9.45 9.84 10.35 11.02

Millimeters (214) (216) (220) (226) (231) (240) (250) (263) (280)

X(Displ. Width)




Case Drain Port

Port B

Port A

1.14

(28.

9)

1.16 (29.5)

Y13.22 (81.8)Y26.37 (161.7)~6.50 (165.1)

MMK SeriesDimensions - Configuration Wheel Mount Flange C


XInches .57 .67 .83 1.06 1.26 1.60 2.03 2.54 3.20

Millimeters (14.4) (17.1) (21.1) (26.8) (32.1) (40.6) (51.5) (64.5) (81.4)

Y1Inches 3.12 3.23 3.39 3.61 3.81 4.15 4.58 5.09 5.76

Millimeters (79) (82) (86) (92) (97) (106) (116) (129) (146)

Y2Inches 5.33 5.43 5.59 5.81 6.02 6.36 6.79 7.30 7.96

Millimeters (135) (138) (142) (148) (153) (162) (172) (185) (202)

X(Displ. Width)




Case Drain Port1.16 (29.5)

MMK SeriesDimensions - Configuration Bearingless Flange D


XInches .57 .67 .83 1.06 1.26 1.60 2.03 2.54 3.20

Millimeters (14.4) (17.1) (21.1) (26.8) (32.1) (40.6) (51.5) (64.5) (81.4)

Y1Inches 3.32 3.43 3.58 3.81 4.02 4.35 4.78 5.29 5.96

Millimeters (84) (87) (91) (97) (102) (111) (121) (134) (151)

Y2Inches 5.52 5.63 5.79 6.01 6.22 6.56 6.98 7.50 8.16

Millimeters (140) (143) (147) (153) (158) (167) (177) (190) (207)

X(Displ. Width)

Port B

Port A1.

14 (2

8.9)

Y1Y21.99 (50.5)~2.08 (52.8)




1.02” (26)~1.04” (26.5)

MMK SeriesMounting Flanges

A = 4-Bolt SAE “B”, Pilot 4” (101.6)

C = 4-Bolt Wheel Flange, Pilot 5.50” (139.7)

4- .57” (14.5)~.60” (15.2)

Ø6.50” (165)

.49” (12.4)

Ø4”

(101

.6)

Ø5.

49” (

139.

57)~

Ø5.

5” (1

39.7

)Ø

4.84

” (12

3) m

axØ

4.27

” (10

8.5)

max

Ø4.

99” (

126.

87)~

5” (1

27)

5.71” (145)

Ø3.07” (78 ± 0.12)

.33” (8.5 ± 0.1)

.48” (12.3)~.49” (12.6)

Ø6.38” (162)

4- Ø.57” (14.5)

4- Ø.57” (14.5 ± 0.15)

Ø6.37” (161.9 ± 0.15)

Ø5.0” (127 ± 0.05)

Ø5.00” (127)

4.69

” (11

9)

3.22” (81.8)

4.69” (119)

45°45°

5.71” (145)

5.71” (145)

5.71

” (14

5)5.

71” (

145)

3.54

” (89

.8)

5.71

” (14

5)

3.54” (89.8)

4- Ø.57” (14.5)

.87” (22)

.35” (9)

.34” (8.6)~.38” (9.7)

.84” (21.3)~.86” (21.8) 1.02” (25.9)

.83” (21.1)~.95” (24.1)

B = 4-Bolt SAE “C”, Pilot 5” (127)

D = 4-Bolt Bearingless, Pilot 5” (127)




2.24” (56.8)~2.33” (59.1)

MMK SeriesShafts

1 = 1.25” (31.75mm) Straight, Flat Key 7.96mmAvailable with Code A Flange Only

Available with Code A & B Flanges Only

Available with Code B Flange Only

Available with Code A Flange Only

Available with Code A & C Flanges Only

Available with Code D Flange Only

5 = 1.625” (41.275mm) Tapered

3 = 1.57” (40mm) Straight, Flat Key 11.96mm

2 = 1.25” (31.75mm) 14t Splined 6 = Bearingless

4 = 1.50” (38.1mm) 17t Splined

Recommended Torque:(645 Nm Dry)(513 Nm Lub)Plus torque required to align the slotted nut with shaft crosshole.

Ø.16” (4.1)

.5” (12.7) .44” (11.1)

.20” (5.2)~.22” (5.54)

3.02” (76.6)

1.25” (31.7)

Ø1.

625”

(41.

275)

1-1/

4-18

UNEF

3.6” (91.4)~3.7” (94)to mounting face

for hub

2.7” (68.5)~2.82” (71.7)

2.09” (53.1) max

.31” (7.96)

1.38” (35.07)~1.39” (35.3)

1.60” (40.6)~1.65” (42)Ø

1.25

” (31

.75)

3/8-

16UN

C

2.09” (53.1) max

2.7” (68.5)~2.82” (71.7)

1.50” (38.1) min

Ø1.

25” (

31.7

5)

3/8-

16UN

C

to mounting face

to mounting face

to mounting face

to mounting face

2.73” (69.3)~2.78” (70.7)

1.68

” (42

.7)~

1.69

” (43

.03)

Flange A = 3.64” (92.5)~3.68” (93.4)Flange B = 3.48” (88.3)~3.52” (89.3)

3.13” (79.6) maxM12x1.75-6H

Deep 24.9

Ø1.

57” (

40)

.47” (11.96)

2.50” (63.5)~2.59” (65.8)

1.23” (31.2) minØ1.30” (33.02)~1.31” (33.28)

Ø1.

5” (3

8.1)

2.04” (51.8) max

(For dimensions see page 64)





MMT SeriesFeaturesMMT series motors are disc valve motors that can be used in parallel or series configurations. A diverse offering of mounting flanges, shafts, ports, and displacements along with wheel and bearingless motors allow for easy installation, product replacement or OEM application.







MODEL CODE (DISPLACEMENT) 01 02 03 04 05 06 07 08

Displ.cm³/r 195 245 310 390 490 625 800 985

in³/r 11.9 15.0 18.9 23.8 29.9 38.1 48.8 60.1

Flow

LPMCont. 150 150 150 150 150 150 150 150

Int. 170 210 225 225 225 225 225 225

GPMCont. 39.6 39.6 39.6 39.6 39.6 39.6 39.6 39.6

Int. 44.9 55.5 59.4 59.4 59.4 59.4 59.4 59.4

Max Speed RPM

Cont. 775 615 485 387 306 240 184 153

Int. 866 834 698 570 454 355 278 230

Pressure

∆BarCont. 170 170 170 170 170 120 120 120

Int. 275 275 275 275 240 140 140 140

∆PSICont. 2466 2466 2466 2466 2466 1740 1740 1740

Int. 3989 3989 3989 3989 3481 2031 2031 2031

Torque

NMCont. 475 615 775 965 1215 1125 1308 1570

Int. 770 980 1225 1455 1685 1330 1650 1875

LBF-INCont. 4204 5443 6859 8541 10754 9957 11577 13986

Int. 6815 8674 10842 12878 14914 11772 14604 16595

Specifications



Series

Displacement in³/r (cm³/r) 01 = 11.9 (195)02 = 15.0 (245)03 = 18.9 (310)04 = 23.8 (390)05 = 29.9 (490)06 = 38.1 (625)07 = 48.8 (800)08 = 60.1 (985)

Flange & PilotA = 4-Bolt SAE Cc Flange, pilot Ø5.00” (127)B = 4-Bolt Flange, pilot Ø4.92” (125)C = 4-Bolt Wheel Flange, pilot Ø5.50” (139.7)D = 4-Bolt Square Mount, pilot Ø6.30” (160)E = 4-Bolt Global Mount, pilot Ø6.30” (160)Similar to ISO3019/2F = 4-Bolt Square, Bearingless, pilot Ø5.00” (127)

Paint0 = No Paint1 = Blue (Standard)2 = Black3 = GreenOptions 0,2 & 3 (or any other color needed) will only be considered for Large Quantity Orders

Ports & Drain PortA = G 1, BSP & G 1/4, BSP B = 1-5/16”-12 O-ring & 7/16”-20UNFC = M33 x 2 & M14 x 1.5D = M33 x 2 & G 1/4 O-ringE = 2-Ø.63” & M14 x 1.5(Standard Manifold Port Face)F = Not AvailableG = G 3/4 & G 1/4, O-ringH = M22 x 1.5 & M14 x 1.5I = M24 x 1.5 & M14 x 1.5J = Not AvailableK = 4-Bolt 3/4” Split Flange (to fit SAEJ518C2) & 7/16”-20UNF, O-ringL = 2-Ø.63” Split Flange & M14 x 1.5 (E2 ref)M = 2-Ø.63” (E3 ref)N = 2-Ø.55” (E4 ref)All motors come with a Steel Hex Socket PluggedDrain Port

All motors for this Series come with Standard (Clockwise) Rotation. For Counter Clockwise Rotation pressurize Port B.

MMT - 01 - A - 01 - D - 1 - A

Shafts01 = 1.50” (38.1mm) Straight, Flat key 9.56mm02 = 1.57” (40mm) Straight, Flat key 12mm (L=84-86mm)03 = 1.57” (40mm) Straight, Flat key 12mm (L=77.7-80.1mm)04 = 1.42” (36mm) Square Spline 8D-42 x 36 x 7 (L=69mm)05 = 1.42” (36mm) Square Spline 8D-42 x 36 x 7 (L=72-74mm)06 = 1.42” (36mm) Square Spline 6D-40 x 35 x 10 (L=66.5-68.5mm)07 = 1.97” (50mm) Straight, Flat key 14mm08 = Non-Standard09 = 1.57” (40mm) Straight, Flat key 12mm (L=58mm)10 = Non-Standard11 = 1.75” (44.42mm) Tapered12 = 1.38” (35mm) Straight, Flat key 12mm (L=84-86mm)13 = 1.42” (36mm) Square Spline 6D-40 x 35 x 10 (L=84-86mm)14 = Non-Standard15 = Non-Standard16 = Non-Standard17 = Non-Standard18 = 1.5” (38.1mm) 17t Splined19 = 1.57” (40mm) Straight, Flat key 12mm “US Standard”20 = Bearingless

StyleA = StandardB = Large BoltC = Wheel

MMT SeriesModel Code Breakdown



MMT SeriesPerformance InformationTo assure best motor life, run motor for approximately one hour at 30% of rated pressure before applying full load.Fill motor with equipment manufacturer’s recommended fluid prior to any load application and startup.

Side Load

Shaft Seal




35 70 105 140 170 205 240 275

FLOW

LP

M

3.8 1752

3651

7.5 18018

37017

55516

73014

87512

10259

11954

15 18538

37537

56035

74033

92029

108022

127514

13705

30 18576

38074

57572

76068

95065

113555

131545

145533

45 185115

385112

580109

770105

965100

115091

134081

154079

61 180154

380151

580147

770143

965132

1155126

1345116

76 180193

380189

580187

775182

970175

1160162

1355152

91 170230

370229

570225

765220

965212

1155204

106 165268

365266

565261

760256

960248

1150236

121 160306

355305

555299

750292

945282

1145269

136 155346

340340

545336

730329

730317

1130301

151 150386

325380

535375

730368

915359

189 130482

300475

515469

730460

910449

227 280570

500562

720552

890538


35 70 105 140 170 205 240 275

FLOW

LP

M

1.9 757

1655

2602

7.5 7537

17035

26534

35030

44026

47018

15 8076

17574

27072

36566

45562

52046

59032

65518

30 85153

180148

275144

370131

465119

545116

62599

70583

45 85230

180225

280221

375212

475203

565186

655167

750148

61 80307

180303

280300

375291

475283

575258

665236

760214

76 80384

180379

280374

380365

480356

575332

670306

770280

91 80462

175456

275450

375440

475429

575413

670388

770363

106 75539

175532

270526

375514

475502

570476

670448

770421

121 70617

170609

270602

370589

470576

570542

670511

765480

136 70692

165683

265674

365659

465645

565601

665564

765527

151 70770

165759

260746

365733

465718

560666

660624

170 65866

160854

260843

360825

460808

555749

655702


35 70 105 140 170 205 240 275

FLOW

LP

M

1.9 954

2151

7.5 10029

22026

34024

44521

55517

57011

6706

15 10560

22556

34554

46048

57542

64039

75030

85512

30 110120

235116

355113

475104

59595

70081

80067

90553

45 110182

235178

360174

480165

605157

720141

840125

955109

61 110244

235240

360236

485228

610221

730202

845184

960165

76 105306

230301

355297

485287

615277

735257

855238

980218

91 105365

230361

355358

480348

610338

735316

860294

980271

106 100426

225421

350416

480404

610376

730358

855340

980322

121 90489

215481

345475

470461

600448

725423

850398

975373

136 80549

210543

335537

460524

580509

710482

840456

151 80612

200606

330599

455585

580570

700540

800510

170 65688

200682

325674

445685

575641

685608

755574

189 195758

315749

440731

555712

670676

208 190834

310824

430804

550783

665744


35 70 105 140 170 205 240 275

FLOW

LP

M

1.9 606

1254

2751

7.5 13023

28022

41020

54017

64514

75510

8804

15 13547

29045

43042

57038

68532

80024

93517

102510

30 14095

30091

45087

59581

73073

87064

98555

110546

45 140143

305140

460135

610129

760121

910111

104599

118588

61 140192

300188

460184

615178

770167

920156

1060141

1205126

76 135241

295236

455232

615226

770216

925201

1075184

1225167

91 130289

295282

455279

615273

775260

930248

1080232

1230215

106 130336

290333

450328

610320

770308

930295

1075276

1225257

121 125384

285381

445375

600368

765354

920341

1065320

136 120430

275421

435416

590410

750396

915383

1055360

151 115478

270466

425461

580456

745441

905427

1040403

189 110597

245582

385576

525570

685551

840534

227 220698

365691

515684

650661

800641

MMT SeriesPerformance Information

Continuous

Intermittent

230301

(Torque Nm)

(Speed RPM)




• Performance data is typical at 120 SUS (25.2 cSt).

• Actual data may vary slightly from unit to unit in production.




15 35 50 70 85 105 120 140

FLOW

LP

M

3.8 2153

4653

6452

8652

10801

7.5 2158

4708

7107

9407

11756

14105

15654

16853

15 22515

48515

77515

96514

120514

144513

157013

179013

30 23030

49530

75030

99529

123528

148027

164026

187525

45 23045

49545

75045

100044

125043

149542

170041

61 22561

49061

74061

99560

124559

150058

76 21577

47577

73076

98576

123575

148574

91 20592

46092

70592

96091

122090

147089

106 185107

445107

700107

950106

1200105

1450103

121 165123

425123

675122

925121

1160120

136 130138

395138

645138

895137

1125135

151 95153

365153

610152

868151

1085150

189 325191

585190

830189

1050188

227 525230

810229

1025226


35 50 70 85 105 120 140

FLOW

LP

M

3.8 4204

5904

7763

9602

7.5 4204

5948

7908

9727

11766

13445

15684

15 43518

60817

84017

102016

120415

130814

165013

30 42036

39635

83035

100534

120433

141531

161029

45 38055

56555

79554

97254

119053

136251

61 34075

52074

76072

94071

117270

76 32593

50092

73090

90089

114087

91 315111

470110

700109

860108

1080105

106 310129

450128

650127

800125

1020123

121 280148

420146

610145

750143

136 270166

400165

550165

700164

151 250184

350183

500182

635180

189 300230

440228

580225

227 380276

520273

MMT SeriesPerformance Information Cont.

Continuous

Intermittent


35 70 105 140 170 205 240

FLOW

LP

M

3.8 2357

4805

6953

7.5 24014

48013

71012

94511

11758

13703

15 23530

48529

72528

96027

119525

141021

164517

30 23560

48559

73557

97554

121551

144545

168538

45 23591

48589

73587

97584

122079

145571

61 235122

480121

730118

975114

1220109

1460100

76 225152

470150

725147

975144

1220139

91 220184

470180

720180

970176

1215171

106 210214

460211

710208

960204

1210198

121 195244

450241

700237

950232

1205226

136 175275

435272

685265

940260

1175255

151 160306

425303

675295

920290

1150284

189 130382

365379

590369

860362

227 325454

550442

805435


35 50 70 85 105 120 140

FLOW

LP

M

3.8 2505

3804

5104

6403

7552

7.5 26012

39513

53513

67010

79510

9258

10606

15 27524

42524

57024

71022

85021

95518

10606

30 29545

45044

60544

75543

92542

109539

127037

45 29572

45071

61071

76570

92068

112566

133064

61 28594

44593

60592

76091

91589

112087

132585

76 280119

440118

595117

755116

915115

1120112

1325110

91 265143

430142

585140

745139

905138

1110135

1320132

106 255168

415166

575165

735164

895162

1105159

1315156

121 240192

400190

560188

720187

880185

1090182

1300179

136 220216

380214

540213

700212

855210

1050207

151 200240

360239

520238

680237

835236

1015233

189 310298

470296

630294

790290

227 255355

430353

590350

745345




• Performance data is typical at 120 SUS (25.2 cSt).

• Actual data may vary slightly from unit to unit in production.

44593

(Torque Nm)

(Speed RPM)



Case Drain Rear

Case DrainCase Drain

Port B

Port B

Port A

Port A

Standard Port Face

Square Port Face

Ø5.

00” (

127)

or Ø

4.92

” (12

5)

Ø6.

30” (

160)

.96 (24.4)

1.34 (34)

.53 (13.5)

.31 (8).28 (7)

2.56 (65)

.79 (20)

Y1

Y1

Y2

Y2

MMT SeriesDimensions - Configuration Flanges A & B

Dimensions - Configuration Flanges D & E

DISPLACEMENT CM³/R 195 245 310 390 490 625 800 985

XInches .86 1.08 1.36 1.71 2.14 2.72 3.50 4.29

Millimeters (22) (27) (35) (44) (54) (69) (89) (109)

Y1Inches 10.63 10.87 11.14 11.50 11.93 12.52 13.11 14.09

Millimeters (270) (276) (283) (292) (303) (318) (333) (358)

Y2Inches 5.91 6.14 6.42 6.77 7.20 7.80 8.43 9.33

Millimeters (150) (156) (163) (172) (183) (198) (214) (237)


XInches .86 1.08 1.36 1.71 2.14 2.72 3.50 4.29

Millimeters (22) (27) (35) (44) (54) (69) (89) (109)

Y1Inches 9.06 9.25 9.69 9.88 10.35 10.91 11.54 12.48

Millimeters (230) (235) (246) (251) (263) (277) (293) (317)

Y2Inches 5.31 5.55 5.83 6.18 6.61 7.20 7.83 8.74

Millimeters (135) (141) (148) (157) (168) (183) (199) (222)

X(Displ. Width)

X(Displ. Width)

G1/4”M14x1.5None





MMT SeriesDimensions - Wheel Mount Flange C, Shaft Code 11

Dimensions - Bearingless Flange F, Shaft Code 20


XInches .86 1.08 1.36 1.71 2.14 2.72 3.50 4.29

Millimeters (22) (27) (35) (44) (54) (69) (89) (109)

Y1Inches 7.28 7.52 7.80 8.15 8.58 9.17 9.80 10.75

Millimeters (185) (191) (198) (207) (218) (233) (249) (273)

Y2Inches 4.06 4.25 4.57 4.88 5.35 5.91 7.01 7.48

Millimeters (103) (108) (116) (124) (136) (150) (178) (190)


XInches .86 1.08 1.36 1.71 2.14 2.72 3.50 4.29

Millimeters (22) (27) (35) (44) (54) (69) (89) (109)

Y1Inches 7.01 7.20 7.52 7.87 8.31 8.90 9.88 10.43

Millimeters (178) (183) (191) (200) (211) (226) (251) (265)

Case Drain Rear

Port B

Port A

Ø5.

00” (

127)

M33

x2

Ø1.

75” (

44.4

25)

.31 (7.87) min.88 (22.3).67 (17)

.22 (5.54)

2.13 (54)

3.87 (98)~3.76 (95.5)

6.88 (174.7)~6.99 (177.5).93 (23.5)~1.05 (26.7)

3.03 (77)

Y1

Y2

X(Displ. Width)

1:81.75” Tapered Shaft

∇

Port B

Port A

Ø5.

00” (

127)

2.68 (68)~2.72 (69.1)

.48 (12.1)~.5 (12.7).89 (22.6 ± 0.15) Y

X(Displ. Width)

SHAFT CODE 20 - DIMENSIONS

Number of Teeth 12

Diametral Pitch 8.5/17

Pressure Angle 30

Major DIa. Ø38.4

Minor DIa. Ø31.5

Space Width 5.7





4- Ø.71” (18)Bolt Circle: Ø7.87” (200)

4- Ø.57” (14.5)Bolt Circle: Ø6.38” (162)

4- Ø.57” (14.5)Bolt Circle: Ø6.38” (162)

MMT SeriesMounting Flanges

5.74

” (14

5.8)

5.74

” (14

5.8)

5.74” (145.8) 5.74” (145.8)

A = 4-Bolt SAE “Cc” Flange, Pilot 5.00” (127) B = 4-Bolt Flange, Pilot 4.92” (125)

C = 4-Bolt Wheel Flange, Pilot 5.50” (139.7) D = 4-Bolt Square Mount, Pilot 6.30” (160)

E = 4-Bolt Global Mount, Pilot 6.30” (160)(Similar to ISO3019/2)

F = 4-Bolt Square Flange, Pilot 5.00” (127)

7.00

” (17

8)7.00” (178)

4- Ø.56” (14.3)

4- Ø.56” (14.3)4- Ø.56” (14.3)

Ø7.25” (184.2)

Ø7.25” (184.2)

Ø6.37” (161.92)

6.51

” (16

5.4)

6.51

” (16

5.4)

6.51” (165.4)

6.51” (165.4)

5.79” (147) x 5.79” (147)Dimensions are in inches (millimeters).



08 = Non-Standard Shaft Code

MMT SeriesShafts

1 = 1.50” (38.1mm) Straight, Flat Key 9.56mm 5 = 1.42” (36mm) Square Splined, 8D 42x36x7

3 = 1.57” (40mm) Straight, Flat Key 12mm 7 = 1.97” (50mm) Straight, Flat Key 14mm

2 = 1.57” (40mm) Straight, Flat Key 12mm 6 = 1.42” (36mm) Square Splined, 6D 40x35x10

4 = 1.42” (36mm) Square Splined, 8D 42x36x7 9 = 1.57” (40mm) Straight, Flat Key 12mm

1.72” (43.8)~1.78” (45.09)

2.07” (52.5)

1.67

” (42

.4)

1.69

” (43

)

Ø1.

50” (

38.1

)Ø

1.57

” (40

)

2.32” (59)

3.19” (81)

3/8-16UNC

C12/19.8GB145-85

.20” (5)

3.31” (84)~3.39” (86)

2.56” (65)

1.69

” (43

)

Ø1.

57” (

40)

3.03” (77)C12/19.8GB145-85

.20” (5)

3.06” (77.7)~3.15” (80.1)

2.48” (63)

2.72” (69)

1.65” (42)

Ø1.

65” (

42)

Ø1.

42” (

36)

2.64” (67)

1.97” (50)

Ø1.

65” (

42)

Ø1.

42” (

36)

2.83” (72)~2.91” (74)C12/19.8GB145-85

2.48” (63)

1.85” (47)

Ø1.

57” (

40)

Ø.9

7” (2

5.3)

2.62” (66.5)~2.70” (68.5)C8/13.2

GB145-85

2.76” (70)

2.11

” (53

.5)

Ø1.

97” (

50)

3.19” (81)3.31” (84)~3.39” (86)

1.97” (50)

1.69

” (43

)

Ø1.

57” (

40)

2.28” (58)C12/19.8GB145-85




10, 14, 15, 16 & 17 = Non-Standard Shaft Codes

MMT SeriesShafts Cont.

11 = 1.75” (44.42mm) Tapered 19 = 1.57” (40mm) Straight, Flat Key 12mm

13 = 1.42” (36mm) Square Splined, 6D 40x35x10

12 = 1.38” (35mm) Straight, Flat Key 12mm 20 = Bearingless

18 = 1.50” (38.1mm) 17t Splined

2.76” (70)

1.52

” (38

.5)

Ø1.

38” (

35)

3.19” (81)C12/19.8GB145-85

.20” (5)

3.31” (84)~3.39” (86)

3.03” (77)

1.25” (31.7)Ø

1.75

” (44

.425

)

1-1/

4-18

UNEF

3.19” (81)

1.39” (35.25)

Ø1.

57” (

40)

Ø.9

7” (2

5.3)

3.31” (84)~3.39” (86)C12/19.8GB145-85

1.59” (40.3)

Ø1.

5” (3

8.1)

2.72” (69)~2.80” (71)3/8-16UNC

2.36” (60 ± 0.2)

3.61” (91.6)~3.72” (94.4)

2.98” (75.6) max

.47” (11.9)

1.68” (42.7)~1.69” (43.0)

2.45” (62.2)~2.51” (63.7)

Ø1.

57” (

40)

M12

x1.7

5-6H

to mounting face

.18” (4.5)~.36” (9.2)

2.68” (68) - 2.72” (69.1)

Ø5.

00” (

127)

.48” (12.1)~.50 (12.7)




MMT SeriesPort Dimensions

.75” (19 ± 0.1) .75” (19 ± 0.1)4-M12

2-Ø.63” (16)

.98” (25 ± 0.1).98” (25 ± 0.1)

1.49

” (37

.9 ±

0.1

)

2.99

” (75

.9 ±

0.1

)

.79” (20 ± 0.3).85” (21.6)

.85” (21.6) .85” (21.6).53” (13.5)

1.26” (32 ± 0.5)

.91” (23 ± 0.6)

.49” (12.5)

4-M10-6H2-G3/4”

.85” (21.6).79” (20 ± 0.3)

Case DrainG1/4”


.76” (19.5) .76” (19.5)

1.47

” (37

.3)

2.86

” (72

.6)

2-1.3125”-12, O-ring

Case Drain7/16”-20UNF

B = 1-5/16”-12 O-ring & 7/16”-20UNF

3.88

” (98

.6)

.57”

(14.

6)1.

48” (

37.6

)2.

23” (

56.6

)

.75” (19)

.87” (22)

1.26” (32 ± 0.1) 1.26” (32 ± 0.1)

.75” (19)

.75” (19 ± 0.1)

.87” (22)4-M12 2-Ø.63” (16)

Case DrainM14x1.5

L = 2-Ø.63” Split Flange & M14 x 1.5

G = G 3/4” & G 1/4”, O-ring

1.49” (37.8)

1.39

” (35

.4 ±

0.1

)

2-M33x2

Case DrainM14x1.5

C = M33 x 2 & M14 x 1.5

M = 2-Ø.63”

.53” (13.5)

.92” (23.4) .92” (23.4)

.92” (23.4) .92” (23.4).53” (13.5)

.53” (13.5)

1.97” (50 ± 0.6)

1.26” (32 ± 0.5)

.91” (23 ± 0.6).53” (13.5)

4-M12-6H2-Ø.55” (14)

N = 2-Ø.55”

.75” (19 ± 0.1).98” (25 ± 0.1)

.98” (25 ± 0.1)

.75” (19 ± 0.1)

1.49

” (37

.9 ±

0.1

)

2.99

” (75

.9 ±

0.1

)

4-M122-Ø.63” (16)

Case DrainM14x1.5

.75” (19 ± 0.1).94” (23.9)

.87” (22.2)

.94” (23.9)

.75” (19 ± 0.1)

1.49

” (37

.9 ±

0.1

)

2.99

” (75

.9 ±

0.1

)

4-Bolt 3/4” Split Flange

Case Drain7/16”-20UNF

E = 2-Ø.63” & M14 x 1.5 (Standard Manifold Port Face)

K = 4-Bolt 3/4” Split Flange

1.49” (37.8)

1.39

” (35

.4 ±

0.1

)

2-M33x2

Case DrainG1/4”

D = M33 x 2 & G 1/4 O-ring

A = G 1” BSP & G 1/4” BSP

1.22” (31)

.94” (24)

2-G1”.92” (23.4 ± 0.5)

1.97” (50 ± 0.6)

Case DrainG1/4”

Case DrainM14x1.5

.84” (21.4 ± 0.5)

.94” (24 ± 0.6)

1.22” (31)

1.89” (48 ± 0.6)

2-M22x1.5

H = M22 x 1.5 & M14 x 1.5

Case DrainM14x1.5

.84” (21.4 ± 0.5)

.94” (24 ± 0.6)

1.22” (31)

1.89” (48 ± 0.6)

2-M24x1.5

I = M24 x 1.5 & M14 x 1.5




MMV SeriesFeaturesMMV series motors are disc valve motors that can be used in parallel or series configurations. A diverse offering of mounting flanges, shafts, ports, and displacements along with wheel and bearingless motors allow for easy installation, product replacement or OEM application.








Displ.cm³/r 310 400 500 630 800 1000 1250

in³/r 18.9 24.4 30.5 38.4 48.8 61.0 76.3

Flow

LPMCont. 160 200 200 200 200 200 200

Int. 200 240 240 240 240 240 240

GPMCont. 42.3 52.8 52.8 52.8 52.8 52.8 52.8

Int. 52.8 63.4 63.4 63.4 63.4 63.4 63.4

Max Speed RPM

Cont. 510 500 400 315 250 200 160

Int. 630 600 480 380 300 240 190

Pressure

∆BarCont. 200 200 200 180 160 160 150

Int. 240 240 240 210 180 180 170

∆PSICont. 2901 2901 2901 2611 2321 2321 2176

Int. 3481 3481 3481 3046 2611 2611 2466

Torque

NMCont. 920 1180 1460 1660 1880 2340 2740

Int. 1110 1410 1760 1940 2110 2640 3120

LBF-INCont. 8143 10444 12922 14692 16639 20711 24251

Int. 9824 12480 15577 17170 18675 23366 27614

Specifications



Series

Displacement in³/r (cm³/r) 01 = 18.9 (310)02 = 24.4 (400)03 = 30.5 (500)04 = 38.4 (630)05 = 48.8 (800)06 = 61.0 (1000)07 = 76.3 (1250)

Flange & PilotA = 4-Bolt Square, pilot Ø6.30” (160)B = 4-Bolt Square, pilot Ø6.30” (160)C = 4-Bolt SAE “C”, pilot Ø5.00” (127)D = 4-Bolt Square, pilot Ø5.00” (127)

Seals0 = Buna (Standard)1 = Viton Shaft Seal & Buna Seals2 = Buna Shaft Seal & Viton Seals3 = Viton Shaft Seal & Viton Seals


Ports & Drain PortA = G 1, BSP & G 1/4, BSPB = 1-5/16”-12UNF, O-ring & 9/16”-18UNF, O-ringC = 16mm (.63”) & G 1/4D = 1-1/4” Split Flange & 9/16”-18UNF, O-ring(Manifold Mount 4-M12)All motors come with a Steel Hex Socket PluggedDrain Port

MMV - 01 - A - 01 - A - 1 - 0 - A

Shafts01 = 1.97” (50mm) Straight, Flat key 13.957mm, M12(Available with Code A & C Flange Only)02 = 2.25” (57.15mm) Straight, Flat key 12.7mm, 3/8-16UNC(Available with Code A Flange Only)03 = 2.125” (53.95mm) 16t, Splined, M12(Available with Code A Flange Only)04 = 2.125” (53.95mm) 16t, Splined, 3/8-16UNC(Available with Code A Flange Only)05 = 1.77” (45mm) 17t, Splined(Available with Code B Flange Only)06 = 2.25” (57.15mm) Straight, Flat key 12.7mm, 1/2-20UNF(Available with Code C Flange Only)07 = 2.125” (53.95mm) 16t, Splined, 1/2-20UNF(Available with Code C Flange Only)08 = 1.65” (41.95mm) Square Splined(Available with Code D Flange Only)09 = 2.25” (57.15mm) Tapered, SAE J501(Available with Code B & C Flange Only)10 = Bearingless

Paint0 = No Paint1 = Blue (Standard)2 = BlackOptions 0 & 2 (or any other color needed) will only be considered for Large Quantity Orders

MMV SeriesModel Code Breakdown



MMV SeriesPerformance InformationTo assure best motor life, run motor for approximately one hour at 30% of rated pressure before applying full load.Fill motor with equipment manufacturer’s recommended fluid prior to any load application and startup.

Side Load

Shaft Seal




30 60 90 120 150 180 210

FLOW

LP

M

10 24413

49411

7498

25 24438

49437

74935

101133

127931

153529

181227

50 24479

49475

74973

101171

127967

153566

181263

75 244117

494115

749112

1011110

1279107

1535105

1812101

100 244157

494154

749151

1011148

1279144

1535143

1812141

125 244196

494192

749188

1011185

1279183

1535181

1812179

150 244236

494231

749229

1011226

1279224

1535221

1812217

175 244275

494269

749267

1011264

1279261

1535258

1812256

200 244314

494308

749305

1011302

1279298

1535295

1812292

240 244377

494370

749366

1011362

1279358

1535354


35 70 105 140 175 200 240

FLOW

LP

M

10 14027

28323

43016

58110

25 14078

28374

43071

58168

73464

83959

101955

50 140160

283153

430148

581144

734137

839134

1019127

75 140237

283235

430227

581223

734218

839213

1019206

100 140319

283313

430306

581300

734294

839290

1019287

125 140399

283391

430383

581375

734371

839367

1019363

150 140479

283469

430465

581460

734455

839450

1019440

160 140511

283501

430495

581490

734485

839480

1019475

200 140639

283626

430619

581613

734606


35 70 105 140 175 200 240

FLOW

LP

M

10 18121

36618

55513

7498

25 18161

36658

55555

74953

94749

108346

131543

50 181124

366119

555115

749111

947106

1083104

131599

75 181184

366182

555176

749173

947169

1083165

1315159

100 181248

366243

555238

749233

947228

1083225

1315223

125 181309

366303

555297

749291

947288

1083284

1315281

150 181371

366364

555360

749356

947353

1083349

1315341

175 181433

366424

555420

749416

947411

1083407

1315403

200 181495

366485

555480

749475

947470

1083465

1315460

240 181594

366582

555576

749570

947564

MMV SeriesPerformance Information

Continuous

Intermittent

494154

(Torque Nm)

(Speed RPM)


35 70 105 140 175 200 240

FLOW

LP

M

10 22617

45714

69410

9366

25 22649

45746

69444

93642

118440

135437

164334

50 22699

45795

69492

93689

118485

135483

164379

75 226147

457146

694141

936138

1184135

1354132

1643128

100 226198

457194

694190

936186

1184182

1354180

1643178

125 226248

457243

694238

936233

1184230

1354228

1643225

150 226297

457291

694288

936285

1184282

1354279

1643273

175 226347

457340

694336

936333

1184329

1354326

1643322

200 226396

457388

694384

936380

1184376

1354372

1643368

240 226475

457466

694461

936456

1184451




25 50 75 100 130 160 180

25 40319

65318

115617

167214

219913

253812

291011

50 40340

65338

115637

167236

219934

253833

291032

75 40359

65358

115656

167255

219954

253853

291051

100 40379

65378

115676

167274

219973

253872

291071

125 40399

65397

115695

167293

219992

253891

291090

150 403119

653116

1156115

1672114

2199113

2538112

2910109

175 403139

653136

1156134

1672133

2199132

2538130

2910129

200 403158

653155

1156154

1672154

2199150

2538149

2910147

240 403190

653186

1156184

1672182

2199180

2538179


25 50 75 100 130 160 180

FLOW

LP

M

15 32212

65311

9918

25 32224

65323

99122

133821

176020

216618

246517

50 32250

65348

99146

133845

176043

216642

246540

75 32274

65373

99171

133869

176068

216666

246564

100 32299

65397

99195

133893

176091

216690

246589

125 322124

653121

991119

1338116

1760115

2166114

2465113

150 322149

653146

991144

1338143

1760141

2166140

2465137

175 322173

653170

991168

1338166

1760165

2166163

2465161

200 322198

653194

991192

1338190

1760188

2166186

2465184

240 322238

653233

991230

1338228

1760226

2166223

MMV SeriesPerformance Information Cont.

Continuous

Intermittent


25 50 75 100 130 160 180

FLOW

LP

M

12 25812

52211

7938

25 25830

52229

79328

107026

140825

173223

197221

50 25862

52259

79358

107056

140853

173252

197249

75 25892

52291

79388

107086

140884

173283

197280

100 258124

522121

793119

1070116

1408114

1732113

1972111

125 258155

522152

793148

1070145

1408144

1732142

1972141

150 258186

522182

793180

1070178

1408176

1732174

1972171

175 258217

522212

793210

1070208

1408206

1732203

1972201

200 258248

522243

793240

1070238

1408235

1732233

1972230

240 258297

522291

793288

1070285

1408282

1732279

253872

(Torque Nm)

(Speed RPM)







Case Drain

Case Drain

Port B

Port B

4-M1212 Deep

4-M1212 Deep

Port A

Port A

.53 (13.5)

.53 (13.5)

.53 (13.5).94 (24)

.94 (24)

2.99 (76)

2.99 (76)

.92

(23.

38)

.92

(23.

38)

.92

(23.

38)

1.97

(50)

1.97

(50)

4.72

(120

)4.

72 (1

20)

.92

(23.

38)

.92

(23.

38)

2.72 (69)

3.24 (82.2)

Y1

Y1

Y2

Y2

MMV SeriesDimensions - Configuration Flanges A & B

Dimensions - Configuration Flange C


XInches .67 .93 1.30 1.69 2.24 2.87 3.50

Millimeters (17) (24) (33) (43) (57) (73) (89)

Y1Inches 7.95 8.19 8.58 8.98 9.53 10.16 10.79

Millimeters (202) (208) (218) (228) (242) (258) (274)

Y2Inches 5.67 5.91 6.30 6.69 7.24 7.87 8.50

Millimeters (144) (150) (160) (170) (184) (200) (216)


XInches .67 .93 1.30 1.69 2.24 2.87 3.50

Millimeters (17) (24) (33) (43) (57) (73) (89)

Y1Inches 8.35 8.58 8.98 9.37 9.92 10.55 11.18

Millimeters (212) (218) (228) (238) (252) (268) (284)

Y2Inches 6.18 6.42 6.81 7.20 7.76 8.39 9.02

Millimeters (157) (163) (173) (183) (197) (213) (229)

X(Displ. Width)

X(Displ. Width)

.92

(23.

38)

.53 (13.5)





MMV SeriesDimensions - Configuration Flange D


XInches .67 .93 1.30 1.69 2.24 2.87 3.50

Millimeters (17) (24) (33) (43) (57) (73) (89)

Y1Inches 8.54 8.78 9.17 9.57 10.12 10.75 11.38

Millimeters (217) (223) (233) (243) (257) (273) (289)

Y2Inches 5.79 6.02 6.42 6.81 7.36 7.99 8.62

Millimeters (147) (153) (163) (173) (187) (203) (219)

Case DrainPort A

4-M1215 Deep

Port B

1.50 (38)3.72 (94.5)

1.50

(38)

4.72

(120

)

3.24 (82.2)

Y1

Y2

X(Displ. Width)

.70 (17.68)

.70

(17.

68)

.70

(17.

68)




MMV SeriesMounting Flanges

A = 4-Bolt Square, Pilot 6.30” (160)

C = 4-Bolt Wheel Flange, Pilot 5.50” (139.7)(U.S. Standard)

1.52” (38.6)~1.55” (39.4)

.52” (13.2)~.54” (13.8) .50” (12.8)~.53” (13.4)

1.02” (25.9)~1.06” (27)

7.01

” (17

8)5.

74” (

145.

8)

5.74

” (14

5.8)

7.01

” (17

8)

7.01” (178)

5.74” (145.8) 5.74” (145.8)

7.01” (178)

.79” (20)

.94” (24) .94” (24)

.79” (20).39” (10) .39” (10)

33°

Ø2.

36” (

60)

Ø2.

36” (

60)

Ø2.

17” (

55)

Ø2.

17” (

55)

Ø3.

27” (

83)

Ø5.

00” (

127)

Ø5.

67” (

144)

Ø5.

00” (

127)

Ø5.

00” (

127)

Ø5.

67” (

144)

Ø6.

30” (

159.

9)6.

30” (

160)

Ø6.

30” (

160)

Ø7.87” (200)

Ø6.38” (162) Ø6.38” (162)

Ø7.87” (200)

4- Ø.71” (18)

4- Ø.67” (17) 4- Ø.67” (17)

4- Ø.71” (18)

B = 4-Bolt Square, Pilot 6.30” (160)

D = 4-Bolt Bearingless, Pilot 5” (127)




MMV SeriesShafts

1 = 1.97” (50mm) Straight, Flat Key 13.957mm 5 = 1.77” (45mm) 17t Splined

3 = 2.125” (53.95mm) 16t Splined 7 = 2.125” (53.95mm) 16t Splined

2 = 2.25” (57.15mm) Straight, Flat Key 12.7mm 6 = 2.25” (57.15mm) Straight, Flat Key 12.7mm

4 = 2.125” (53.95mm) 16t Splined 8 = 1.65” (41.95mm) Square Splined

4.76” (121)~4.84” (123) 3.83” (97.2)~3.92” (99.5)

2.76” (70)~2.78” (70.5) 1.69” (43) min

2.09” (53.2)~2.11” (53.5)

.18” (4.5)~.22” (5.5)

3.22” (81.8)~3.24” (82.2)

3.11” (79)

1.02” (26)

2.45” (62.2)~2.47” (62.8)

M12 C12/19.8GB145-85

60°.55” (13.957)

Ø1.

97” (

50)

Ø2.

17” (

55)

Ø2.

36” (

60)

Ø1.

77” (

45)

Available with Code A Flange Only Available with Code B Flange Only

Available with Code A Flange Only Available with Code C Flange Only

Available with Code A Flange Only Available with Code C Flange Only

Available with Code A Flange Only Available with Code D Flange Only

4.76” (121)~4.84” (123) 4.43” (112.5)~4.54” (115.3)

3.05” (77.5)~3.13” (79.5)

2.53” (64.3)~2.55” (64.7)

3.89” (98.8)~3.91” (99.2)

2.18” (55.3)~2.22” (56.3)

2.24” (56.9)~2.26” (57.5) 2.76” (70.2)~2.77” (70.4)

1.89” (48) min

2.47” (62.6)~2.48” (62.9)

2.47” (62.6)~2.48” (62.9)

Ø1.40” (35.5)~1.41” (35.8)

.43” (10.9)~.52” (13.1)

3.22” (81.8)~3.24” (82.2)

.79” (20) min1.02” (26) min

1.02” (26) min

3/8-16UNC 1/2-20UNF

1/2-20UNF

A6.3/13.2GB145-85

60° 60°

60°

.50” (12.7) .50” (12.7)

.27” (6.95)~.28” (6.987)

Ø2.

25” (

57.1

5)

Ø2.

25” (

57.1

5)

Ø2.

36” (

60)

Ø2.

36” (

60)

Ø2.

17” (

55)

Ø1.

65” (

41.9

5)

4.76” (121)~4.84” (123)

4.76” (121)~4.84” (123)

2.20” (56)~2.28” (58)

2.20” (56)~2.28” (58)

3.22” (81.8)~3.24” (82.2)

3.22” (81.8)~3.24” (82.2)

1.02” (26)

.79” (20) min

M12

3/8-16UNC

45°

45°

Ø2.

125”

(53.

95)

Ø2.

125”

(53.

95)

Ø2.

36” (

60)

Ø2.

36” (

60)

Ø2.

125”

(53.

95)

Ø2.

36” (

60)

3.55” (90.2)~3.66” (93)3.01” (76.5)~3.03” (76.9)




Special Options

Seals A = Buna (Standard)B = Viton Shaft Seal & Buna SealsC = Buna Shaft Seal & Viton SealsD = Viton Shaft Seal & Viton Seals

Setup1 = Standard2 = Free Running3 = Seal Guard4 = Dacromet Screws & Plug5 = Free Running & Dacromet Screws & Plug6 = Seal Guard & Dacromet Screws & Plug7 = Dust Seal Ring8 = Anti-cavitation Port

Shaft Coating1 = Standard (No Coating)2 = Chrome Plated

W - A - 1 - A - 1 - A

Speed SensorsA = Standard (None)B = Ported & Plugged, No SensorC = Ported with Speed SensorD = Ported with Speed SensorFor speed sensor options contact [email protected] or your local salesman

Motor CoatingA = Standard (No Coating)B = Nickel PlatedC = Nickel Plated Motor, Shaft & Bolts

Above options are non-stock. Please call or email for availability.

All Series Special OptionsModel Code Breakdown

GMOMTC Rev 04.2017 © Hydraulex Global. All Rights Reserved.

Hydraulex Global Corporate48175 Gratiot AveChesterfield, MI 48051Toll Free: 800.422.4279Tel: 586.949.4240

www.hydraulex.com

Hydraulex Global - Michigan Tel: 586.949.4240 [email protected] Global - Mississippi Tel: 601.469.1987 [email protected] Global - Ontario Tel: 416.638.6000 [email protected] Global - Washington Tel: 253.604.0400 [email protected] Global - Tennessee Tel: 901.794.2462 [email protected]

Connect with us:

· Inline Piston Pumps· Radial Piston Pumps & Motors· Bent Axis Piston Pumps & Motors· Fixed Volume Vane Pumps· Variable Volume Vane Pumps· Gear Pumps· Vane Motors

· Axial Piston Motors· High Speed Motors· Servo Motors· Orbital Motors· Directional Valves· Flow Control Valves· Pressure Control Valves

· Relief Valves· Check Valves· Stack Valves· Servo Valves· Proportional Valves· PTOs (Power Take-offs)· Cylinders

Products We Offer

Hydraulex Global - A Recognized Global Leading Provider of High Quality Hydraulic Components

All manufacturers names, symbols and descriptions in this document are used for reference purposes only, and it is not implied

that any parts listed is the product of these manufacturers.

genuine metaris orbital motor technical catalog€¦ · genuine metaris orbital motor technical...

Documents