geotechnical & structural instrumentation · table of contents 3. inclinometer inclinometer...
TRANSCRIPT
WWW.SMARTEC.CH
Swiss Monitoring at Your Service
GEOTECHNICAL & STRUCTURAL INSTRUMENTATION
PRODUCT CATALOG
SMARTEC SA was founded in 1996, resulting from the development of the Fiber Optic SOFO monitoring system at Swiss Federal Institute of Technology, Lau-sanne (EPFL).
In 2000, the company integrated the DiTeSt system (Brillouin) and the DiTemp system (Raman) in its solutions. In 2005, the MuST product line, based on Fiber Bragg Grating, was intro-duced.
In 2006, SMARTEC joined Roctest, a world leading manufac-turer of instrumentation used in civil engineering, geotechnical and industrial applications. In 2010, Roctest became part of Nova Metrix.
SMARTEC has over 100 years of combined experience in Fiber Optics. You can communicate with SMARTEC in Italian, English, French, German, Spanish and Russian. Our experi-ence and expertise are reflected by more than 1000 monitor-ing projects in 30 countries throughout the world.
SMARTEC is committed to provide the best solution with the highest quality products, services, support and competence.
Fiber Optic Sensing
SMARTEC product range and expertise cover all major fiber optic sensing technolo-gies. We have been pioneers in the use of optical fiber sensors for Structural Health Monitoring and process control.
Optical fiber sensors offer key advantages compared to tradi-tional electrical sensors making them ideal for applications where other sensors are difficult or impossible to deploy:
• Immunity to Electromagnetic iInterference (EMI), Radio Frequency Interference (RFI) and lightning
• Non-conducting cables, requiring no grounding or lightning protection
• Possibility to use very long cables (up to several kilome-ters) without repeaters or signal degradation
• Sensors can be used in explosive environments
• Sensing elements are made of glass and are not subject to aging, corrosion or damage from water ingress
• Ability to combine multiple sensors in a single sensing line
SMARTEC Services SMARTEC offers several engineering services to support our customers in the design, implementation and manage-ment of both simple and complex Structural Health Monitor-ing (SHM) systems. This includes everything from the selec-tion of the optimal sensors, data acquisition units and data management software, to the definition of the best strategies for data analysis and sensor placement. SMARTEC's Solu-tion & Services Team has considerable field experience to support you in the management and execution of your moni-toring projects:
In particular, we offer the following services:
System Design
• Risk / Opportunity analysis in collaboration with design engineers and owners
• Establish expected responses to degradation (e.g. corro-sion, cracks, leak). Design of the SHM system and se-lection of the appropriate sensors to meet the objectives
Installation, Operation and Maintenance
• On-site support and training on installation and testing of the sensors and data acquisition systems - either with your staff, our team or our world-wide qualified partners
• Remote support for troubleshooting and system perfor-mance monitoring
• Extended warranty, hot-swap systems and regular pre-ventive maintenance
Data Management
• Commissioning, datalogger programming and data man-agement systems. Remote access configuration
• Real-time advanced data representation. Generation of warnings and alerts, based on complex conditions
Data Analysis
• Data validation and data quality check
• Data interpretation in line with the original criteria estab-lished in cooperation with the lead engineer
2 SMARTEC PROFILE
Profile
+
FIBER OPTIC - DITEMP - DITEST DiTemp External Multiplexer…………………………….…….. 15
DiTemp Relay Module Switch………………………….……… 15
DiTeSt SMARTape II Strain Sensor……...………….….……. 15
DiTeSt SMARTprofile II Strain Sensor…………………….…. 15
DiTeSt Strain HDPE Sensor…...…………………….……….. 16
DiTeSt / DiTemp Hydro & Geo Sensor………..……………... 16
DiTeSt / DiTemp Ordinary Temperature Sensor….…….….. 16
DiTeSt / DiTemp Medium Temperature Sensor……………... 16
DiTeSt Reading Unit BOTDA…….………...………….…….… 17
DiTeSt Dual Reading Unit BOTDA/BOTDR………….…….… 17
DiTeSt Multiple Channel Optical Switch...………………….… 17
Laser Distance-Meter 3Demon…..……………………………. 17
SOFTWARE
SDB Software…………………………………………………… 18
DiView Software….……………………………………...……... 18
VDV Software Vista Data Vision..…………………………….. 18
FIBER OPTIC - FABRY-PEROT POINT SENSING
Fiber Optic Strain Gauge FOS-N ..……...………………….… 8
Fiber Optic Embedded Strain Gauge EFO.………………….. 8
Fiber Optic Total Pressure Cell TPC……………..…………… 9
Fiber Optic Single-Channel Portable Readout FOR-1…...…. 9
Fiber Optic Multi-Channel Tabletop Datalogger UMI .…….... 9
Fiber Optic Multi-Channel Datalogger FODL-1600/3200 …….. 9
Evolution Chassis ..…………………….…………………….... 10
Fiber Optic Spot-Welded Strain Gauge SFO-W…………….. 8
Evolution Modules…………….………………………………… 10
Fiber Optic Temperature Sensor FOT-T…...………………… 8
Fiber Optic Piezometer FOP ………………………………….. 7
Fiber Optic Piezometer FOP MICRO PZ……………..……… 7
Fiber Optic Displacement Sensor FOD...………….…………. 7
Fiber Optic Temperature Sensor FOT-F…...………………… 7
FIBER OPTIC - SOFO/MUST
MuST FBG Deformation Sensor …….……………………….. 10
MuST FBG Strain Sensor .………….…………………………. 10
MuST FBG SMARTprofile Sensor .……………………….….. 11
MuST FBG Temperature Sensor ...……………...…………… 11
MuST FBG Tiltmeter ………………………...…..…………….. 11
MuST FBG Accelerometer….…….………………….………... 11
SOFO Deformation Sensor.……………….………………..…. 12
SOFO LiTE Reading Unit….………………………...………... 12
SOFO VII / MuST FBG Portable Reading Unit………..…….. 12
MuST Dynamic FBG Reading Unit.…..………………..……... 12
SOFO VII / MuST FBG Universal Reading Unit...…...……… 13
FIBER OPTIC - DITEMP - DITEST DiTemp Temperature Sensors……….……………………….. 13
DiTemp Self-Heating Sensors……….………………….…….. 13
DiTemp Light Reading Unit……………………………………. 13
DiTemp HARSH Reading Unit………………………………... 14
DiTemp HARSH+ Reading Unit………………………..……... 14
DiTemp Reading Unit…………………………………..……… 14
DiTemp ATTS (Automated Trip Testing System)…………... 14
TABLE OF CONTENTS
SMARTEC PROFILE……………………………………….. 2
FIBER OPTIC SENSING…………………………………… 5
Vibrating Wire Piezometer PW Series ……………………… 20
Multi-Level Piezometer PWML ………………………………. 20
Pneumatic Piezometer FPC-2 & FPC-2D ………………….. 20
Standpipe Piezometer CP1 & CP15…………………………. 20
PIEZOMETER
EXTENSOMETER Magnetic Reed Switch Probe Extensometer R-4………….. 21
Tape Extensometer CONVEX –D…………………………… 22
Vibrating Wire Jointmeters JM-S & JM-E…………………… 22
Borehole Extensometer BOR-EX ……..…………………….. 22
Retrievable Borehole Extensometer BOF-EX……………… 22
Crackmeter RTF 1D & 3D……………………………………. 23
Crackmeter RTV 3D………...………………………………… 23
Fill Extensometer ERI………………………………………… 23
Portable Jointmeter PF 8..……………………………………. 23
TRADITIONAL SENSING…………………………………. 19
WATER LEVEL SYSTEM Water Level Indicator CPR…………………………………… 21
V-Notchh / Water Level Sensor NIVOLIC WL………………. 21
Staff Gage………………………………………………………. 21
3 TABLE OF CONTENTS
INCLINOMETER Inclinometer System PROFIL………………………………… 24
Vertical In-Place Inclinometer PISA-M ...…………………… 24
Horizontal In-Place Inclinometer HORIZON-M .……………. 24
Flexible Inclinometer Chain RT-FXI ...……….….…..………. 24
Inclinometer Casing GEO-LOK………………………….….... 25
Anchors or Grout Plugs GEO-LOK....………………….……. 25
Telescoping Section GEO-LOK.……………………….…….. 25
Inclinometer Casing GTI-1A …………………………………. 25
LOAD & PRESSURE CELL Vibrating Wire Load Cell VH ………………………………… 28
Anchor Load Cell ANCLO …………………………………… 28
Hydraulic Load Cell HYDLO …………………………………. 28
Total Pressure Cell TPC ...…………………………………… 28
STRAIN
Surface Mount Strain Gauges SM-5 Series………………… 29
Miniature Strain Gauges SM-2 Series………………………. 29
Embedded Strain Gauge EM Series………………………… 29
Vibrating Wire Strain Gauge C-110 ….……………………… 29
Instrumented Rebar IRHP…………………………………….. 30
SETTLEMENT Settlement System Nivolic SG ...…………………………….. 30
Soil Settlement Gauge SSG .………………………………… 30
Settlement Cell TCP .………….……………………………… 30
TEMPERATURE Temperature Sensor TH Series ……………………………... 31
Thermistor String TH-C…………………………………….…. 31
MISCELLANEOUS Electrical Instrumentation Cable …...………………………… 31
Inflatable Packer LP & MP.……………………………………. 31
READOUT / DATALOGGER
Vibrating Wire Readout MB-3TL……………………………… 32
Portable Datalogger PFC-12 ..………………………………... 32
Compact Datalogger RT-VLOG…………...………………….. 32
Pneumatic Pressure Indicator PR-20 & PR-20D……………. 32
Data Acquisition System SENSLOG……….………………… 33
Switching Box RT-VWSB ..……………………………………. 33
Signal Multiplexer RT-MUX 16/32 ………………………….… 33
Wireless Interface Module SL Series….……………………... 33
PENDULUM / TILTMETER Pendulum DIRECT & INVERTED …………………………… 26
Remote Reading Pendulum Station RxTx..………………… 26
Sighting Reading Table / MVR ……………………………… 26
Beam Sensor & Tiltmeter EL BEAM………………………… 26
MEMS Tiltmeter MEMS TILT………………………………… 27
Wireless MEMS Tiltmeter LS-G6-INC15 …………………… 27
Electrolytic Tiltmeter TUFF TILT 420 ..………………….….. 27
Digital MEMS Tiltmeter JDI-100, JDI-200..…………….…… 27
ANALYZER / WIRELESS / VIBRATION
VW Analyzer CAMPBELL SCIENTIFIC……………………… 34
Wireless Mesh Networking SENSEMETRICS ..…………….. 34
Wireless Star Networking LOAD-SENSING……..………….. 34
Vibration Monitor Micromate INSTANTEL…..…………….… 34
4 TABLE OF CONTENTS
Pressuremeter TEXAMe..……………………………….…..… 36
Borehole Dilatometer PROBEXe………………………….….. 36
Borehole Dilatometer DMP-95e..……………………..………. 36
Dilatometer / Pressuremeter D/P BOX.……………..……….. 36
Pressuremeter G-AM II………………………………..………. 37
Pressuremeter TRI-MOD-S…………………………………… 37
Pressuremeter PENCEL………………………………………. 37
Self-Boring Pressuremeter BOREMAC……………………… 37
Vane Borer M1000.……………………………………..……… 38
Field Inspection Vane Tester H-60…………………………… 38
Penetrometer HSA-5…………………………………...……… 38
Penetrometer PEM-1………………………………..…………. 38
Hoek Triaxial Cell HTC...……………………………..…..…… 39
Point Load Tester PIL-7……………………………..………… 39
Fall Cone Apparatus G-200…………………………………… 39
SMARTEC– EQUIPMENT RENTALS………………………. 39
IN-SITU / LAB TESTING EQUIPMENT 35
TABLE OF CONTENTS
Fiber Optic Sensing SMARTEC’s product range and expertise cover all major fiber optic sensing technologies. Optical fiber sensors offer several advantages compared to traditional sensors making them ideal for applications where other sensors are difficult to deploy.
• Immunity to Electromagnetic Interference (EMI), Radio Frequency Interference (RFI) and Lightning. • Non-conducting cables, requiring no grounding or lightning protection. • Able to use very long cables (up to several kilometers) without repeaters or signal degradation. • Sensors can be used in explosive environments.
FIBER OPTIC SENSING
FIBER OPTIC SENSING
5 FIBER OPTIC - SENSING
+
FIBER OPTIC - TECHNOLOGIES
Fiber Optic Technologies • Fabry-Perot Interferometer (FISO):
These point sensors measure local strain, temperature, pressure and displacement. These values are encoded in a change of length of an optical cavity within the sensors that can be measured accurately. Fabry-Perot sen-sors offer excellent long-term stability. They are the ideal optical replacement for conventional geotechnical sensors.
• Low-Coherence Interferometers (SOFO):
These long-gauge sensors measure displacement or average strain over measurement bases that can extend up to several meters. They are ideal transducers for monitoring concrete and geotechnical structures. Defor-mations are measured by observing the length changes of an optical fiber attached to the structure under ob-servation, compared to a loose reference fiber. This measurement principle allows accurate and stable meas-urements and insensitivity to temperature variations.
• Fiber Bragg Grating (MuST):
FBG sensors are written in the optical fiber core and act as optical filters, reflecting the wavelength that match-es the grating pitch. The reflected wavelength depends on the strain and temperature of the grating, enabling measurement of those two parameters and others that can be transformed to strain (deformation, tilt and accel-eration). It is possible to combine multiple gratings with different reflective wavelength on the same fiber (multiplexing).
• Distributed Raman Scattering (DiTemp):
These sensors use an intrinsic property of optical fibers to measure the local average temperature of each me-ter of fiber for lengths up to several tens of kilometers. This enables the measurement of thousands of tempera-tures along a single cable. This technology is particularly suitable for detecting and localizing hot or cold spots associated with leaks or other defects.
• Distributed Brillouin Scattering (DiTeSt brand):
This technology is similar to Raman scattering, but offers the additional ability to measure distributed strain. This enables the detection of local events such as settlements, deformations, cracks and movements.
ABBREVIATIONS
AC: Alternating Current power supply (e.g. 110 – 220 V)
BOTDA: Brillouin Optical Time Domain Analyzer
DC: Direct Current power supply (e.g. 12 – 24 V) DiTemp: Distributed Temperature Sensing
(Raman DTS, R-OTDR) DiTeSt: Distributed Temperature and Strain Sensing
(Brillouin, B-OTDA)
DTS: Distributed Temperature Sensing
EMF: Electromagnetic Fields
EMI: Electromagnetic Interference
F.S.: Full Scale
FBG: Fiber Bragg Grating
HDPE: High Density Polyethylene
MMF: Multi Mode Optical Fiber
MuST: Multiplexed Strain and Temperature Sensors (FBG)
MUX: Mulitplexer
O.D.: Outer Diameter
OTDR: Optical Time Domain Reflectometer
RFI: Radio Frequency Interference
RU: Reading Unit
SIL: Safety Integrity Level
SMF: Single Mode Optical Fiber SOFO: Surveillance des Ouvrages par Fibres Optiques
(Monitoring with Optical Fiber Sensors)
FIBER OPTIC - TECHNOLOGIES 6
FIBER OPTIC - FABRY-PEROT POINT SENSING
FIBER OPTIC PIEZOMETER FOP Series
The FOP Fiber Optic Piezometer is designed to measure pore water or other fluid pressure. It is used for applications such as hydraulic structures, foundations, dams, embankments and waste repository sites. It is built with a rugged stainless steel body for harsh environ-ments. Accurate and reliable, it is intrinsically safe and immune to EMI, RFI and lightning.
SPECIFICATIONS
Range 200 to 7,000 kPa
Outside diameter 19, 25 or 33 mm
Length 100 to 210 mm
Accuracy ±0.25% F.S.
Resolution 0.025% F.S.
FIBER OPTIC PIEZOMETER FOP MICRO PZ
The FOP-MicroPZ Fiber Optic Piezometer is designed to measure pore water or other fluid pressure. Its very small diameter of 4.8mm al-lows a range of applications where no other piezometer can be used, such as a small diame-ter pipe. The body of the MicroPZ is made of rugged stainless steel for harsh environments. Accurate and reliable, it is intrinsically safe and immune to EMI, RFI and lightning.
SPECIFICATIONS
Range2 100, 200, 3501, 500, 750, 1,000 kPa
Accuracy ±0.5% F.S.
Resolution 0.065% F.S.
Dimensions 4.8 mm (O.D.), 54 mm (Length)
Optional FOP-PZ with plastic filter for ma-rine environment; Packaged into 116 mm PVC housing 16 mm OD
FIBER OPTIC DISPLACEMENT SENSOR FOD
The FOD Fiber Optic Linear Position and Dis-placement Transducer is used to monitor relative movements of adjacent surfaces across cracks or construction joints in concrete, rock and metal structures. Based on Fabry-Perot interferometry principle, it is available in either a rugged stainless steel or aluminum housing for harsh environments. Accurate and reliable, it offers high resolution, intrinsic safety and im-munity to EMI, RFI and lightning.
SPECIFICATIONS
Range 20 or 40 mm (spring-loaded shaft)
Accuracy ±1% F.S. (20 mm)
Resolution 0.002 mm
Length 144 mm
PIEZ
OMET
ER
PIEZ
OMET
ER
TEM
PERA
TURE
EX
TENS
OMET
ER
FIBER OPTIC TEMPERATURE SENSOR FOT-F
The robust FOT-F Fiber Optic Temperature Sensor is used mainly for temperature measurements in harsh environments. Minia-ture and rugged, it may be embedded in con-crete or installed in open air. Intrinsically safe, it is immune to EMI, RFI and lightning.
SPECIFICATIONS
Range −40°C to +85°C (cable dependent)
Accuracy ±1% F.S.
Resolution 0.1°C
Length 51 mm
7 FIBER OPTIC - FABRY-PEROT POINT SENSING
1 Standard 2 Other ranges available as custom products
FIBER OPTIC - FABRY-PEROT POINT SENSING
FIBER OPTIC - FABRY-PEROT POINT SENSING 24
STRA
IN
SPECIFICATIONS
Range ±1,000, ±1,500, ±2,000, ±3,000μɛ
Accuracy Range dependent
Resolution 0.01% F.S.
Operating temperature −40°C to +85°C
Gauge dimensions 12.5mm (dia.) x 70mm (length)
Thermal sensibility -0.1 µm/m / °C
FIBER OPTIC EMBEDDED STRAIN GAUGE EFO
STRA
IN
STRA
IN
TEM
PERA
TURE
SPECIFICATIONS
Range ±1,000, ±1,500, ±2,000μɛ
Accuracy Range dependent
Resolution 0.01% F.S.
Operating temperature −40°C to +85°C
Gauge dimensions 4.7mm (width) x 50.8mm (length)
Thermal sensibility -0.1 µm/m / °C
The SFO-W Fiber Optic Strain Gauge is used for long-term, precise strain measurements on a variety of structures including nuclear power plants, dams corrosive environments. It is suitable for spot-welding on steel surfaces. Intrinsically safe, it allows static/dynamic measurements, low thermal sensitivity (silica) and can deliver signals transmitted over long distances.
FIBER OPTIC SPOT-WELDED STRAIN GAUGE SFO-W
The EFO Fiber Optic Strain Gauge is designed to be embedded in concrete. It may be cast directly into a wet mixture or encapsulated into a concrete briquette to be cast into a wet mix-ture. Intrinsically safe, it is immune to EMI, RFI and lightning. It allows static/dynamic meas-urements, low thermal sensitivity (silica) and its signal can be transmitted over long distanc-es with no interference due to fiber bending.
SPECIFICATIONS
Range ±1,000, ±2,500, ±5,000µɛ
Accuracy Range dependent
Resolution 0.01% F.S.
Operating temperature −40°C to +250°C
Gauge diameter 230 μm
Thermal sensibility -0.1 µm/m / °C
The FOS-N Fiber Optic Strain Gauge is used to measure the deformation of materials due to mechanical stress or thermal effects in nuclear power plants, building monitoring and several civil engineering applications. Intrinsically safe, it allows static/dynamic measurements, low thermal sensitivity (silica) and can deliver sig-nals transmitted over long distances with no interference due to fiber bending.
FIBER OPTIC STRAIN GAUGE FOS-N
FIBER OPTIC TEMPERATURE SENSOR FOT-T
The FOT-T Fiber Optic Temperature Sensor is packaged in either a 51 mm stainless steel or PVC housing. Intrinsically safe, it is immune to EMI, RFI and lightning. PVC housing is particu-larly recommended for salt water applications.
SPECIFICATIONS
Range −40°C to +85°C (cable dependent)
Accuracy ±1% F.S.
Resolution 0.1°C
Housing Stainless Steel or PVC
Outside diameter 16 mm
Length 51 mm
FIBER OPTIC - FABRY-PEROT POINT SENSING 8
FIBER OPTIC - FABRY-PEROT POINT SENSING
1 Higher ranges available as a custom product
SPECIFICATIONS
Pressure range1 200 to 7,000 kPa
Resolution 0.025% F.S.
Options Fiber optic extension cable
Accuracy ±0.25% F.S.
The TPC Total Pressure Cell consists of a sealed pad filled with oil connected via stiff tubing to a fiber optic pressure transducer. It is used for measurement of total pressure in soils and embankments, for measurement of stress in concrete, or for measurement of contact pressures on retaining walls, piles and tunnel linings. Intrinsically safe, it is immune to EMI,RFI and lightning.
CELL
FIBER OPTIC TOTAL PRESSURE CELL TPC
FIBER OPTIC MULTI-CHANNEL DATALOGGER UMI
The UMI Multi-Channel Datalogger is de-signed to read any Fabry-Perot fiber optic trans-ducer. It comes in a 4 or 8-channel version and can be programmed via the front panel interface or through the RS-232 port. The UMI has a non-volatile memory buffer that can store up to 50 000 data samples (discrete or average). Each channel has a dedicated ±5V adjustable analog output.
FIBER OPTIC SINGLE-CHANNEL PORTABLE READOUT FOR-1
The FOR-1 Single-Channel Datalogger is designed to read Fabry-Perot fiber optic trans-ducer. It can store up to 50 000 data samples (discrete or average). The front panel is equipped with a display for programming log-ging sequences, durations and other operational parameters. Battery-powered, the FOR-1 ad-justable analog output offers the possibility to connect to conventional loggers or monitoring systems.
SPECIFICATIONS
Precision 0.025% F.S.
Resolution 0.01% of F.S.
Number of channels 1
Sampling rate 10 Hz standard (other available)
Communication RS-232
Dimensions and weight 9.0 × 16.5 × 4.8 cm, 0.9 kg
Power supply AC + Battery
FIBER OPTIC MULTI-CHANNEL DATALOGGER FODL – 1600/3200
DATA
LOGG
ER
DAT
ALOG
GER
SPECIFICATIONS
Precision 0.025% F.S.
Resolution 0.01% of F.S.
Number of channels 4 or 8
Sampling rate 20 Hz (one specific channel)
Communication RS-232 and USB 1.1
Dimensions and weight 19.0 × 21.1 × 9.7 cm, 2 kg
Power supply AC
SPECIFICATIONS
Precision 0.025% F.S.
Resolution 0.01% of F.S.
Number of channels 16 or 32
Sampling rate 20 Hz
Communication RS-232
Dimensions and weight 44.5 x 49.5 x 22.5 cm, 17 kg
Power supply AC
The FODL – 1600/3200 Datalogger is de-signed for applications that require continuous monitoring of a large number of fiber optic sen-sors. It is fully compatible with Fabry-Perot fiber optic transducers. The FODL – 1600/3200 comes in a 16 or 32 channel version mounted in a NEMA 4X enclosure. The FODL – 1600/3200 can store up to 50000 samples (discrete or average).
DAT
ALOG
GER
9 FIBER OPTIC - FABRY-PEROT POINT SENSING
FIBER OPTIC - FABRY-PEROT / MUST FBG
MuST STRAIN SENSOR FBG
The MuST FBG Strain Sensor transforms a static or dynamic distance variation into a change in reflected wavelength of a pre-stressed Fiber Bragg Grating that can be meas-ured with a MuST reading unit. The strain sen-sors are designed to be bonded or spot welded to structures and components (metal, concrete, etc.). These sensors are fiber optic versions of the conventional resistance strain gauges but completely passive, offering inherent insensitivi-ty to thermal drift.
STRA
IN
EVOLUTION CHASSIS SD-2, SD-5 & Rackmount RM-8
The EVOLUTION Chassis allows easy assem-bly for up to 2 to 5 modules on the tabletop racks and for up to 8 modules on the rack mount unit. USB communication interface is available on all chassis for configuration and data logging via computer. An external data acquisition system, connected to the analog output, is required for ac-quisition rate > 5k samples/sec.
EVOLUTION MODULES FPI-HR, FPI-HR DUAL & FPI-HS
READ
OUT
REA
DOUT
SPECIFICATIONS
Communication USB Data logging Via Computer (not included) Number of module Up to 2, 5 or 8
Dimensions 13.3 x 17.7x 15.6 cm (EVO-SD-2) 26.9 x 17.7 x 15.6 cm (EVO-SD-5) 48.3 x 13.2 x 17.5 cm (EVO-RM-8)
Power supply 24VDC
SPECIFICATIONS
Measurement range ±2000 με
Accuracy ± 2 με
Resolution ±1 με
Operating temperature -20°C to +80ºC
Packaging dimensions Polyimide: 40 x 12 x 0.2 mm Weldable: 83 x 23 x 6 mm Composite: 130 x 20 x 6 mm
The EVOLUTION Platform is the first off the shelf modular monitoring system designed for projects monitoring and tests with Fabry-Perot fiber optic sensors. A variety of modules are available to optimize reading needs. Evolution modules are compatible with SCAI intelligent con-nectors containing calibration parameters for auto-matic configuration. Evolution platform is a mod-ular concept (DIN-rail), upgradeable and expanda-
SPECIFICATIONS
Resolution Strain: ± 0.01% FS Temperature: 0.01°C Pressure: ±0.05% FS Displacement: 0.002 mm
Number of channels 1 or 2 per module
Sampling rate 125 Hz / 250 Hz / 15 kHz
Communication RS-232 & RS-485 + Analog out-put 0 to 5V, optional 4-20 mA
Dimensions 4.5 x 10.3 x 12.6 cm
MuST DEFORMATION SENSOR FBG
The MuST FBG Deformation Sensor transforms a static or dynamic distance variation into a change in reflected wavelength of a pre-stressed Fiber Bragg Grating. These long gauge sensors are surface mountable or embeddable in concrete and permit static/dynamic defor-mation measurements. They are insensitive to corrosion and immune to EMF and RFI. An optional sensor can be provided for temperature compensation.
DEFO
RMAT
ION
SPECIFICATIONS
Length of active zone 1m (20 cm to 2 m upon request)
Measurement range - 0.5% to +0.75%
Strain resolution / accuracy
0.2 με / 2 με
Temperature resolution / accuracy
0.1°C / 0.5°C (using FBG RU)
Operating temperature -50°C to +110°C (+170°C upon request)
FIBER OPTIC - FABRY-PEROT / MUST FBG 10
FIBER OPTIC - MUST FBG
FIBER OPTIC - MUST FBG 11
MuST SMARTprofile SENSOR FBG
The MuST FBG SMARTprofile Sensor consists of a reinforced composite profile inside which an embedded strain-sensing FBG is installed. The SMARTprofile strain sensor transforms a strain variation into a change in reflected wave-length of a FBG. These sensors are compatible with MuST Reading Units. These sensors can withstand high hydraulic pressure. A tempera-ture sensor can optionally be embedded in the same profile at the end of the sensor.
STRA
IN
SPECIFICATIONS
Measurement range ±0.5% (±1 mm)
Accuracy <0.2%
Resolution 2 με
Operating temperature -55°C to +200°C
Sensing profile dimen-sions
Width: 7.8 mm Thickness: 2.9 mm Length: 680 mm
MuST TEMPERATURE SENSORS FBG
The MuST Temperature Sensor is an intrinsi-cally safe sensor that can be embedded or surface mounted. These sensors are fiber optic versions of the conventional electrical tempera-ture sensors but completely passive, offering inherent insensitivity to environmental induced drift. Furthermore, the sensors are immune to electric sparks, EMI/RFI and lightning.
MuST TILTMETER FBG
The MuST FBG Tiltmeter is an inclination/tilt sen-sor based on Fiber Bragg Grating. It is designed to measure small variations of angle towards the verti-cal without the need for temperature compensation by using two FBGs in an innovative push-pull con-figuration. The fiber optic design ensures intrinsic immunity to EMI/RFI and lightning.
SPECIFICATIONS
Measuring range 10 deg (±5 deg)
Accuracy 0.05 deg
Resolution 0.002 deg Operating temperature -20°C to 80°C
Dimensions 220 x 140 x 42.5 mm
SPECIFICATIONS
Measurement range -20°C to +80°C standard
Accuracy ±0.5 °C
Resolution ±0.1 °C
Dimensions General: 140 x 8 mm Weldable: 45 x 15 x 0.3 mm Embedded: 60 x 10 mm
TEM
PERA
TURE
TI
LTM
ETER
MuST ACCELEROMETER FBG
The MuST FBG Accelerometer is suitable for a large range of applications. This FBG sensor is a fiber optic version of the conventional accelerome-ter but completely passive. The sensor is insensi-tive to environmentally induced noise and EMI/RFI.
SPECIFICATIONS
Sensitivity 75 pm/g @ 40 Hz
Frequency range 0 to 50 Hz
Measuring range ± 10 g
Resolution ±12.5 mg
Accuracy 0.1 pm/√ Hz (typical)
Operating temperature -20°C to 80ºC
Dimensions 35 x 20 x 20 mm
ACCE
LERO
MET
ER
FIBER OPTIC - SOFO / MUST FBG
FIBER OPTIC - SOFO / MUST FBG 12
SOFO VII / MuST FBG PORTABLE READING UNIT
The SOFO VII MuST FBG Portable Reading Unit has 4 channels, each channel able to connect up to 5 SOFO sensors (external 1x5 splitter needed) and from 7 to 25 MuST sen-sors (depending on sensor type). The unit con-tains a PC that provides data logging and re-mote interfacing functionalities.
MuST DYNAMIC FBG READING UNIT
The MuST Dynamic FBG Reading Unit is a Fiber Bragg Grating demodulator based on a proven scanning laser engine. It can be inte-grated in a weather tight steel housing and it is used for permanent installation, allowing dy-namic and static measurements for up to 8 sensor strings. The reading unit is designed for a variety of demanding small and large scale industrial and civil engineering applications.
READ
OUT
READ
OUT
READ
OUT
SOFO Lite READING UNIT
The SOFO Lite Reading Unit is able to meas-ure up to 10 or 12 SOFO (Interferometric) sen-sors. SOFO sensors offer the best accuracy and temperature compensation performance for long-gauge sensing. The system is designed for static, long-term measurements and moni-toring of civil structures. The SOFO Lite is inte-grated in a compact housing designed for in-
SPECIFICATIONS
Measurement range Max. 50 mm for SOFO, 100 nm (1500 to 1600 nm) for MuST
Measurement resolution 2 μm RMS SOFO 1 pm MuST (FBG)
Measurement accuracy < 2% SOFO, ±2 pm MuST
Measurement time < 2 s (typ. 1s)
Available channels 4 configurable for SOFO or MuST
Sensors per channel 5 SOFO (using SOFO Splitter) Up to 16 MuST (FBG)
SPECIFICATIONS
Measurement range Max. 50 mm
Measurement resolution 2 μm RMS
Measurement accuracy < 2 ‰
Measurement time < 2 s (incl. SDB writing) per ch.
Communication Ethernet
Available channels 10 or 12 channels total
Data logging Via computer, SENSLOG, DAS or industrial controller (not included)
SPECIFICATIONS
Measurement range 100 nm (1500-1600 nm) MuST (FBG)
Measurement resolution 5 pm MuST (FBG)
Measurement accuracy ± 10 pm
Available channels 1 / 4 / 8 channels
Sensors per channel Max 7 MuST Deformation sensors Up to 12 strain FBG sensors Up to 25 temperature FBG sensors
Sample rate 1000 S/s
DEFO
RMAT
ION
SOFO DEFORMATION SENSOR
The SOFO Deformation Sensor transforms a distance variation into a change in the path unbalance between two optical fibers that can be measured with the SOFO Reading Unit. The SOFO sensor measures deformation with mi-crometer resolution. It is embeddable, surface mountable and insensitive to temperature, cor-rosion and vibration. Furthermore, it is immune to EMI or RFI fields and needs no calibration.
SPECIFICATIONS
Length of active zone Standard: 0.25 to 10 m Special length: 10 to 20 m
Measurement range - 0.5% to +1%
Accuracy 0.2% of the measured deformation
Resolution 2 µm (0.002 mm)
Operating temperature -50°C to +110°C (+170°C upon request)
FIBER OPTIC - SOFO / MUST FBG / DITEMP
13
The SOFO VII/Must FBG Reading Unit is able to read all SOFO and MuST sensors. Each of the 4 or 8 channels can be used to read either SOFO or MuST FBG sensors. The unit contains a PC for remote configuration and datalogging. It is integrated in a compact steel housing, de-signed for permanent installation. It is a conven-ient solution where long-term continuous static monitoring of structures is required.
SOFO VII/ MuST FBG UNIVERSAL READING UNIT
READ
OUT
SPECIFICATIONS
Measurement range Max. 50 mm for SOFO, 100 nm(1500 to 1600 nm) for MuST
Measurement resolution 2 μm RMS SOFO 1 pm MuST (FBG)
Measurement accuracy < 2% SOFO, ±2 pm MuST
Available channels 4 or 8 configurable for SOFO or MuST (FBG) reading.
Sensors per channel 5 SOFO (using SOFO Splitter) Up to 16 MuST (FBG)
DiTemp DISTRIBUTED SELF-HEATING SENSORS
DiTemp LIGHT READING UNIT - DTS
The DiTemp Distributed Self-Heating Sensor cable are used for leak and seepage detection applications, where the temperature contrast between the ground and the leaking fluid to be monitored is small. The cable contains optical fibers to measure temperature and copper wires to heat the cable through the use of electrical current. This enables the determination if the surrounding soil is dry, wet or if water is flowing around it.
The DiTemp Light Reading Unit is designed for distributed temperature measurements over distances of up to 4km with 2 m spatial resolu-tion and 10s measurement time. Featuring a built-in 4 channel multiplexer, this rack mounta-ble unit can be complemented with a relay mod-ule and an ATTS self-testing system, SIL 2 assessment. It is the most cost-effective solu-tion for distributed temperature sensing.
DiTemp DISTRIBUTED TEMPERATURE SENSORS
The DiTemp Distributed Temperature Sensor cables have an armored construction and a plastic sheath. They offer excellent mechanical protection from external pressure, crushing and rodents, while enabling a rapid reaction to tem-perature changes thanks to the small cross-section and use of thermally conductive materi-als. Different cable designs enable measure-ments in standard or extended temp. ranges.
TEM
PERA
TURE
RE
ADOU
T TE
MPE
RATU
RE SPECIFICATIONS
Number of fibers 1, 2 or 4 temperature fibers
Temperature range –190°C to 300°C depending on cable type
Dimensions depending on cable type
Weight depending on cable type
1Values depend on each other
SPECIFICATIONS
Number of fibers 4 temperature fibers 8 isolated copper wires
Temperature range -40°C to +85°C
Dimensions 14.5 mm diameter
Weight 240 kg / km
SPECIFICATIONS
Measurement range 0 to 4 km
Spatial resolution 2 m
Temperature resolution1 0.1°C
Acquisition time1 Min. 10 seconds, typ. 2 min.
Number of channels 4
Operating Temperature 0°C to 40°C
Dimensions 8.7 x 43.5 x 44.5 cm
FIBER OPTIC - SOFO / MUST FBG / DITEMP
FIBER OPTIC - DITEMP
DiTemp READING
DiTemp ATTS
The DiTemp Reading Unit is designed for dis-tributed temperature measurements over dis-tances of up to 60km with 1m spatial resolution and 10s measurement time. It is available in multimode and single mode versions. This rack mountable unit can be complemented with external multiplexers (4, 8, 16 channels), a relay module and an ATTS self-testing sys-tem, SIL 2 assessment.
The DiTemp ATTS is a self-testing fully inde-pendent safety-check system that is able to produce a controlled localized thermal anomaly (hot spot or cold spot) and verify its correct detection. This allows a continuous verification of system availability and a periodic evaluation of the confidence level, SIL proven by experi-ence.
ATTS
RE
ADOU
T
SPECIFICATIONS
Size of hot/cold spot 2 m
# of hot/cold spots 2
Maximum T° change ± 15°C / 10s
Heat/cool period 10 s to 5 minutes (factory set)
Heat/cool cycle 1 minute to 24h (factory set)
Dimensions 9 x 43.5 x 48 cm
SPECIFICATIONS
Measurement range XR12 0-12 Km, XR20 0-20 Km XR30 0-30 Km, XR450-60 Km
Spatial resolution 1 m (< 20 Km ), 2 m (>20 Km)
Temperature resolution Down to 0.1 C°
Acquisition time Min. 10 seconds, typ. 2 min.
Number of channel 1 (external multiplexer available)
Dimensions 18 x 43.5 x 48 cm
READ
OUT
DiTemp HARSH READING UNIT - DTS
The DiTemp Harsh Reading Unit is designed for distributed temperature measurements over distances of up to 12 km with 1m spatial resolu-tion and 10s measurement time. Featuring a built-in 4 channel multiplexer, this rack mounta-ble unit can be complemented with a relay module and an ATTS self-testing system, SIL 2 assessment. It features an extended opera-tional temperature range.
SPECIFICATIONS
Measurement range SR 0-5 km, XR 0-12 km
Spatial resolution 1 m
Temperature resolution 0.1°C
Acquisition time Min. 10 seconds, typ. 2 min.
Number of channels 4
Operating temperature SR - 40°C + 65°C XR - 5°C + 65°C
Dimensions 11.45 x 30.35 x 36.57 cm
READ
OUT
DiTemp HARSH+ READING UNIT - DTS
The DiTemp Harsh+ Reading Unit is provided with an embedded PC for remote configuration and datalogging. It is designed for distributed temperature measurements over distances of up to 30 km with 1m spatial resolution and 10s measurement time. Featuring a built-in 4 chan-nel multiplexer, this rack mountable unit can be complemented with a relay module and an ATTS self-testing system, SIL 2 assess-ment.
SPECIFICATIONS
Measurement range SR 0-5 km, XR12 0-12 km XR20 0-20 km, XR30 0-30 km
Spatial resolution 1 m (SR,XR12), 2 m (XR20, XR30)
Temperature resolution 0.1°C
Acquisition time Min. 10 seconds, typ. 2 min.
Number of channels 4
Operating temperature - 5°C + 65°C
Dimensions 11.45 x 30.35 x 36.57 cm
FIBER OPTIC - DITEMP 14
DiTemp EXTERNAL MULTIPLEXER
The DiTemp EXTERNAL MULTIPLEXER enables a DiTemp to measure up to 16 different sensor cables from one location (up to 480 km of sensing cable per DiTemp reading unit, de-pending on reading unit). Where large scale coverage is required, adding the multiplexer unit is one of the most cost effective sensing solutions.
FIBER OPTIC - DITEMP / DITEST
DiTemp RELAY MODULE SWITCH
The DiTemp RELAY MODULE SWITCH is the ideal complement to the DiTemp reading units when simple alarm transmission is required. The unit can be programmed to open or close relay contacts (24, 48 or 72) based on multiple alarm criteria and multiple zones along the sensing cables. Possible alarm criteria include absolute temperature, rate of temperature change, leak detection, seepage detection, watchdog etc.
MUL
TIPL
EXER
RE
LAY
MOD
ULE
FIBER OPTIC - DITEMP / DITEST 15
SPECIFICATIONS
Number of channels 4 8 16
Dimensions 8.8 x 48.3 x 47.3 cm
Power Supply Powered by DiTemp Reading Unit
Compatibility DiTemp Reading Unit only
SPECIFICATIONS
DiTemp relay module 24 48 72
Dimensions 8.8 x 48.3 x 47.3 cm
Power Supply Powered by DiTemp Reading Unit
Compatibility All DiTemp Reading Unit
DiTeSt SMARTape II STRAIN SENSOR
The DiTeSt SMARTape II Strain Sensor is designed for surface installation on smooth surfaces or for embedding into composites. The DiTeSt SMARTape II sensor consists of a single mode optical fiber embedded in a Glass Fiber Reinforced Polymer tape. The tape itself provides excellent mechanical, chemical and temperature resistance. The small size of the tape makes the sensor easy to transport and install.
DiTeSt/ DiTemp SMARTprofile II STRAIN SENSOR
STRA
IN
SPECIFICATIONS
Number of fibers 1 strain fiber
Temperature range 0°C to 120°C (operation, long term) -5°C to 50°C (installation, storage) -40°C to 80°C (pigtails, connectors)
Strain range Max. –1% compression to +1% elonga-tion depending on installation)
Dimensions ~ 0.32 x ~ 9.9 mm
Weight ~ 3.8 ± 0.2 kg / km
SPECIFICATIONS
Number of fibers 2 strain SM fibers (DiTeSt) 2 temperature SM fibers (DiTeSt) 2 temperature MM fibers (DiTemp)
Temperature range -40°C to 60°C
Strain range -1.5% to +1.5%
Dimensions ~ 4 x ~ 8 mm
Weight 22 ± 0.5 kg / km
This DiTeSt / DiTemp SMARTprofile II Strain Sensor is designed for embedding in con-crete and soil as well as surface installation on uneven surfaces or grooves. For optimal redun-dancy, the cable contains two bonded and four free single mode optical fibers embedded in a polyethylene thermoplastic rectangular profile. The bonded fibers measure strain, while the four free fibers are used for temperature com-pensation.
STRA
IN &
TEM
P
FIBER OPTIC - DISTRIBUTED TEMPERATURE & STRAIN - DITEST / DITEMP
FIBER OPTIC - DITEST / DITEMP
16
DiTeSt / DiTemp DISTRIBUTED ORDINARY TEMPERATURE SENSOR
The DiTeST / DiTemp ORDINARY Tempera-ture Sensing Cable is a unique sensor for the evaluation of distributed temperature over several kilometers. It is used in a wide range of applications, such as monitoring of concrete in massive structures, waste disposal sites, on and off shore sites in the oil & gas industry, hot spots, cold spots and leakage detection of flow lines and reservoirs.
DiTeSt / DiTemp DISTRIBUTED MEDIUM TEMPERATURE SENSOR
The DiTeST / DiTemp MEDIUM Temperature Sensing Cable is a unique sensor for the evaluation of distributed temperature over sev-eral kilometers. It is used in a wide range of applications, such as monitoring of concrete in massive structures, waste disposal sites, on and off shore sites in oil & gas industry, hot spots, cold spots and leakage detection of flow lines and reservoirs.
SPECIFICATIONS
Number of fibers 2 temperature fibers
Temperature range -40°C to 150°C
Dimensions 3.8 mm diameter
Weight 28 kg / km
SPECIFICATIONS
Number of fibers 2 or 4 temperature fibers
Temperature range -40°C to 85°C
Dimensions 3.8 mm diameter
Weight 26 kg / km
TEM
PERA
TURE
TE
MPE
RATU
RE
DiTeSt DISTRIBUTED HDPE STRAIN SENSOR
The DiTeSt HDPE Strain Sensor is recom-mended for a wide range of applications that require distributed strain sensing, such as soil movement and ground monitoring. The DiTeSt HDPE Strain sensor is a small flexible mini armored fiber optic strain sensing cable with central metal tube containing a single optical fiber, metallic armoring wires and HDPE outer sheath.
SPECIFICATIONS
Number of fibers 1 strain fiber
Temperature range -40°C to 85°C
Strain range -1% to +1%
Dimensions 3.5 mm diameter
Weight 19 kg / km
DiTeSt / DiTemp DISTRIBUTED HYDRO & GEO SENSOR
The DiTeSt / DiTemp HYDRO & GEO Sensor measures distributed strain and temperature and is recommended for embedding in soil and concrete or for integration in a geotextile. The cable has a circular cross section and contains 4 singlemode and 2 multimode redundant opti-cal fibers, for use with DiTeSt and DiTemp reading units for distributed strain and tempera-ture monitoring respectively.
STRA
IN
STRA
IN &
TEM
P SPECIFICATIONS
Number of fibers 4 strain SM fibers (DiTeSt) 2 temperature MM fibers (DiTemp)
Strain range -1% to +1%
Temperature range -20°C to 70°C
Dimensions 6.5 mm diameter
Weight 28 kg / km
Optional Armored cable, 12.3 mm diameter
FIBER OPTIC - DITEST / LASER 17
FIBER OPTIC - DITEST / LASER DISTANCE METER
DiTeSt DUAL READING UNIT - BOTDA/BOTDR
The DiTeSt DUAL Reading Unit is a unique tool for the evaluation of distributed strain and/or temperature over several tens of kilometers, allowing the measurement of thousands of loca-tions on a single optical fiber. DiTeSt Dual pro-vides 4 channel fast and accurate strain and temperature measurements up to 50 km in BOTDA mode and up to 45 km with BOTDR single-end mirrorless measurement.
SPECIFICATIONS
Measurement range Up to 10 km or 50 km
Spatial resolution 1 m over 20 km, 2 m over 30 km 3 m over 50 km
Strain resol. / accuracy 2 με / 20 με
T° resolution / accuracy 0.1°C / 1°C
Power Supply AC
Number of channels 4
Dimensions 44.9 x 50 x 17.8 cm
READ
OUT
LASE
R DI
STAN
CE M
ETER
The 3DeMoN Laser Distance Meter allows per-manent monitoring of millimeter-scale move-ments. The measurements are performed be-tween the laser distance meter and remote re-flective targets (if needed). Its modular design allows chaining up to 10 laser instruments and it is ideal for geotechnical and civil engineering applications.
3DeMoN LASER DISTANCE METER
SPECIFICATIONS
Range 0.05 t0 150 m or 0.5 to 500 m
Measurement time 0.3 – 4 sec.
Targets 0.2 m – 50 m 50 m– 400 m >400 m
None Reflecting target or surface Geodetic prism may be needed
Achievable accuracy (standard deviation)
±0.2 mm (indoor measurements) ±1.5 mm (outdoor measurements)
DiTeSt READING UNIT - BOTDA
The DiTeSt Reading Unit is a unique tool for the evaluation of distributed strain and/or tempera-ture over several tens of kilometers, allowing the measurement of thousands of locations on a single optical fiber. The DiTeSt system is based on distributed Brillouin Scattering in optical fi-bers. DiTeSt provides 4 channels with fast and accurate strain and temperature measure-ments up to 60 km in BOTDA mode.
SPECIFICATIONS
Measurement range Up to 60 km (120 km total loop dist.)
Spatial resolution 1 m to 20 m
Strain resol. / accuracy 2 με
T° resolution / accuracy 0.1°C / 1°C
Power Supply AC
Number of channels 4
Dimensions 44.9 x 50 x 17.8 cm
READ
OUT
DiTeSt MULTIPLE CHANNEL OPTIC SWITCH
The Multiple Channel Fiber Optic Switch is specifically designed to extend the monitoring capabilities of the DiTeSt Reading Unit by providing additional channels. The use of the DiTeSt switch is particularly suitable for the kind of application where a monitoring network is needed; power distribution, complex civil engi-neering structures, oil and gas, and well moni-toring. Compatible with DiTeSt BOTDA and DiTeSt Dual BOTDA/BOTDR reading units.
SPECIFICATIONS
Number of channels 4 min up to 20 max
Number of switching cycles
10 Mio
Power Supply AC
Dimensions 44.9 x 30.5 x 13.25 cm SWIT
CH
SOFTWARE
SOFTWARE 18
SDB SOFTWARE
SDB Software offers a unified tool for measurement and monitoring data acquisition and manage-ment. The SDB software package is designed to manage the acquisition, storage, analysis and visualization of static data from fiber optic and conventional sensors. It is compatible with all SMARTEC and Roctest data acquisition units. All data is acquired automatically at pre-defined intervals and stored in a unique relational database. The data can be used to generate alerts based on complex multi-sensor criteria and the software allows the interface to other external systems such as SCADA.
The SDB Pro software is part of the SDB software suite. It simplifies data interpretation, visualization and analysis using real-time calculated virtual sensors called macro-sensors. The value of a macro-sensor is obtained by applying user-defined mathematical functions to the measurements data from real sensors or other macro-sensors, and is stored in a SDB database. The definition of macro-sensors is performed using a user-friendly interface. The representation and properties of this sensor are the same as those of real sensors, i.e. they can be visualized in tables and diagrams and used in alarm criteria.
DiView SOFTWARE
SDB View is part of the SDB suite. It enables easy data navigation and visualization of measure-ments and database. SDB View enables a simultaneous display of multiple user-defined views on sensors chosen from the database over a defined monitoring period. The display can be in form of a map, a table or a graph plot with associated options such as threshold plots, colors and sounds on alert criteria. New views can be generated by the user without any programming and can be exported in different formats for further analysis or publishing.
SOFT
WAR
E SO
FTW
ARE
S
OFTW
ARE
VDV SOFTWARE VISTA DATA VISION
VISTA DATA VISION (VDV) is a comprehensive web-based sensor data management system for long term measurements, storing data in a database, offering web access, alarm service, reports and application specific data handling toolkits for various disciplines. VDV has a powerful and flexible control of all aspects of trend lines and graphs, including, color, thickness, Moving Average, single or dual Y-scales, automatic and fixed Y-scales and linear and logarithmic Y-scale and X-scale (time axis).
VDV includes useful features to associate sensor data with various information. Your data will be sent to your own server or to a cloud server. The imported data can now be viewed on the VDV web based interface. You can organize your data as you like, create dashboards, real time displays, graphs, alarms, give others access to the data and much more. Data can be automatically uploaded from SDB.
The Distributed Data Management and Analysis DiView Software is designed for data storing, processing, representation and analysis, as well as for the control of single or multi-ple DiTeSt and DiTemp reading units. The main functions of DiView software are aimed to measure sensors automatically.
The operator can view in real time the measurements and the alarms on one or multiple maps/graphs. DiView is also able to trigger alerts for different types of events, including strain, tempera-ture, leakage and crack monitoring. DiView can interface relays status and alerts to SCADA sys-tem .
Traditional Sensing Solution Founded in 1967, Roctest, the leading manufacturer of geotechnical and structural health mon-itoring instruments. The products are used in all phases of projects: from the initial planning, construction, operation to rehabilitation.
Roctest Solutions are used in applications such as dams, tunnels, mines, bridges, cliffs, historical monuments, buildings, pipelines, nuclear power plants, offshore / downhole and LNG storage facilities.
Roctest has always been committed to providing high quality service along with the highest level of competence and support.
TRADITIONAL SENSING 19
TRADITIONAL SENSING
TRADITIONAL SENSING
PIEZOMETER 20
PIEZOMETER
VIBRATING WIRE PIEZOMETER PW Series
SPECIFICATIONS
Range1 35 to 7,000 kPa
Accuracy ±0.1% F.S
Length 200 mm to 260 mm
Resolution with MB-3TL 0.025% F.S.
Outside diameter 19 mm to 38 mm
1 Higher ranges available
MULTI-LEVEL PIEZOMETER PWML
The PWML Multi-Level Vibrating Wire Piezo-meter is the perfect tool for measuring pore pressures at various depths inside one bore-hole. It allows for quick and reliable installation since multiple PW-Series Piezometers are connected to a single communication cable. The placement of each sensor along the communi-cation cable is defined by the customer as each multi-level is custom manufactured.
SPECIFICATIONS
Range 200 to 7,000 kPa
Accuracy ±0.1% F.S.
Resolution 0.025% F.S.
Length Sensor placement & total length are custom manufactured.
PNEUMATIC PIEZOMETER FPC-2 & FPC-2D
The FPC-2 Pneumatic Piezometer measures fluid pressure in soil and at the interfaces or in the vicinity of buried structures. The brass or stainless steel construction of FPC-2 makes it suitable for use for both short and long-term monitoring. Low-air or high-air entry filters are available in the FPC-2. Two models are availa-ble: model FPC-2 for borehole installation and model FPC-2D to be pushed into soft soil.
SPECIFICATIONS
Range 0 to 3,500 kPa
Accuracy ±0.25% of pressure gauge
Outside diameter 32 mm
Diaphragm volumetric displacement
<0.01 cm2
STANDPIPE PIEZOMETER CP1 & CP15
The CP Standpipe Piezometer used to measure pore water pressure and water level in permea-ble soils within geotechnical applications such as slope stability, dam performance and em-bankments. It also measures the effectiveness of ground improvement techniques, the effect of construction on surrounding structures, the drawdown due to dewatering and pump tests, as well as the seepage through earth structures.
SPECIFICATIONS
Length 300 mm to 600 mm
Diameter 19 mm to 38 mm
Filter Plastic, ~50 microns, ~10 kPa low air entry
PIEZ
OMET
ER
PIEZ
OMET
ER
PIEZ
OMET
ER
PIEZ
OMET
ER
The PW Vibrating Wire Piezometer is designed to measure pore water or other fluid pressure. It is used for applications such as hydraulic struc-tures, foundations, dams, embankments, exca-vations, tunnels and waste repository sites. The PW has a rugged stainless steel body with triple stage water protection. It offers reliable surge protection and a high level of resistance to EMI and RFI.
WATER LEVEL SYSTEM / EXTENSOMETER 21
WATER LEVEL SYSTEM / EXTENSOMETER
The CPR Water Level Indicator is used to measure the depth of water in boreholes, stand-pipes and wells. Light and compact, it offers an accurate and quick readout of water depth. The CPR is available in a large variety of lengths suitable for all needs. It offers an adjustable sensitivity control with an audible and visual
V-NOTCH WEIR / WATER LEVEL SENSOR NIVOLIC WL
The STAFF GAGE provides a direct visual indi-cator for determining water level. They are de-signed for easy mounting to a wall or pier, with heavy metal grommets and an 0.188 inch open-ing for screws or nails. Each gage consists of a metal core, coated with porcelain enamel and marked with accurate measurement marking at specific intervals.
WATER LEVEL INDICATER CPR-6
The R-4 Magnetic Extensometer is used to measure settlement or heave in engineered backfill structures (dikes, earthfill dams, road foundations) or in natural slopes or embank-ments. The system consists of an access pipe or standpipe, anchor magnets and a portable reed switch probe. It may be used with inclinom-eter casings (70 or 85 mm) to obtain both lateral and vertical movement profiles or with standard PVC access pipe (33 or 48 mm).
MAGNETIC REED SWITCH PROBE EXTENSOMETER R-4
The V-NOTCH is made from stainless steel. On both sides of the notch are engraved two scales showing water levels and corresponding flow rates.
SPECIFICATIONS
Height 16 gauge metal core covered with a bakedon porcelain
Graduation Porcelain enamel
STAFF GAGE
SPECIFICATIONS
Tape length 30 to 150 m
Graduation 1 mm or 0.1 ft
Anchor types Datum ring, push-in or leaf spring
Probe diameter 16 mm
WAT
ER LE
VEL
WAT
ER LE
VEL
EXTE
NSOM
ETER
W
ATER
LEVE
L
SPECIFICATIONS (of the probe)
Diameter 11 mm
Weight 0.110 kg
Tape length1 30, 50, 60, 100 , 150, 200 m
Length 175 mm
Construction Stainless steel, nylon and brass
The NIVOLIC WL uses a vibrating wire hydrau-lic level sensor to measure water level changes. When combined with a weir, it allows for contin-uous monitoring of water flow. It is therefore commonly used for assessing performance of a dam during its filling and operation.
NIVOLIC WL SPECIFICATIONS
Range 100, 150, 300, 450, 600 mm
Accuracy of sensor ±0.1% F.S.
Resolution 0.002% F.S. (min)
V-NOTCH SPECIFICATIONS
Material Stainless steel
Graduation Laser engraving
V-Notch Angle 22.5°, 45°, 60° & 90°
A C I E M
1 Other lengths available on request
EXTENSOMETER
EXTENSOMETER 22
VIBRATING WIRE JOINTMETER JM-S & JM-E
The JM Displacement Transducer is used for monitoring displacements between concrete lifts in concrete dams. Easy to install, extremely stable and reliable, it is also used to monitor separation of shotcrete from a rock face in tun-nel walls as well as to determine crack and joint movement in structures. Ruggedly built, it con-sists of a vibrating wire sensor inside a telescop-ic stainless steel housing.
SPECIFICATIONS
Range1 25 to 300 mm
Accuracy ±0.25% F.S. (±0.1% optional)
Resolution 0.02% F.S.
Waterproof Up to 5 MPa
Operating temperature −20°C to +80°C
TAPE EXTENSOMETER CONVEX-D
The CONVEX-D Tape Extensometer is used to quickly and accurately measure changes in distance between two reference points. It is primarily used to monitor convergence in under-ground excavations such as tunnels. It can also be used to monitor deformations in structures or surface movements.
SPECIFICATIONS
Range 20 or 30 m
Operation temperature 0 to 40°C
Repeatability ±0.1 mm
Weight 2 kg
RETRIEVABLE BOREHOLE EXTENSOMETER
The BOF-EX Incremental Borehole Exten-someter, unlike rod-type extensometers, is designed with 32 mm OD rigid tubing sections to eliminate possible bending and friction be-tween rods. The thermal effect is significantly reduced because the temperature in the bore-hole is less prone to fluctuations. Each measur-ing module is placed inside the borehole next to the anchor. A variety of rod and anchor types are available.
BOREHOLE EXTENSOMETER BOR-EX
The BOR-EX Borehole Rod Extensometer is used to transmit all anchor displacements from zones of movement in soil masses to a collar reference plate for mechanical readings (dial or depth gauge). To simplify reading or remote monitoring, standard electrical head assemblies are available with potentiometer or vibrating wire transducers. Stainless steel or fiberglass rods are available with a variety of anchors.
SPECIFICATIONS
Range1 25 to 250 mm
Anchors 1 to 6 (in a 76 mm borehole)
Anchor types Groutable, hydraulic, leaf spring
Accuracy / Resolution1 ±0.25% F.S. / 0.02% F.S.
Stainless steel rod Fiberglass rod
6.4 mm O.D. 6.4 mm or 9.5 mm O.D.
EXTE
NSOM
ETER
EX
TENS
OMET
ER
EXTE
NSOM
ETER
EX
TENS
OMET
ER
1 Depending on the transducer type
SPECIFICATIONS
Standard range1 5 to 100 mm
Accuracy1 ±0.1% F.S.
Resolution 0.02% F.S.
Operating temperature1 −40°C to +80°C
1 Depending on the transducer type
1Depending on the model
EXTENSOMETER
EXTENSOMETER 23
CRACKMETER RTF 1D & 3D
The RTF Crackmeter is used to measure dis-placement of cracks in structures or rock mass-es. The sensor is housed in a rugged waterproof enclosure which is fitted at one end with a spring-loaded rod resting against the reference surface located on the opposite side of the dis-continuity. Supplied with installation template, the RTF is available in triaxial (RTF 3D) or uni-axial (RTF 1D) version.
SPECIFICATIONS
Range1 25 to 150 mm
Resolution1 0.02% F.S.
Operating temperature1 −20°C to +80°C
Accuracy1 ±0.25% F.S.
1 Depending on the transducer type
CRACKMETER RTV 3D
The RTV 3D Mechanical Crackmeter is used for direct measurement with a caliper of two adja-cent surfaces in three orthogonal directions. This robust instrument is ideal when shear, sliding and tension movements need to be sur-veyed. Easy to install, the RTV 3D requires two drilled holes of 40 mm diameter by 50 mm depth. The legs are grouted in place and read-ings begin when the initial set occurs.
FILL EXTENSOMETER ERI
The ERI Fill Extensometer is designed to moni-tor longitudinal displacements between two points inside any type of man-made fill. It is usually installed horizontally in trenches. It may also be installed vertically to measure settle-ment at the point of contact with the foundation. It is also used to monitor the crest of earthfill dams to locate tension cracks.
SPECIFICATIONS
Range 50 to 200 mm standard
Resolution 0.02% F.S.
Operating temperature −20°C to +80°C
Accuracy ±0.25% F.S.
Sensor type Vibrating wire
PORTABLE JOINTMETER PF 8
The PF 8 Portable Jointmeter is a practical and affordable instrument used to measure relative displacement of cracks or joints over time. The PF8 jointmeter consists of a spring-loaded dial indicator that is set between 8 mm stainless steel reference balls. Extension rods are availa-ble to extend the gauge length of the jointmeter. Fixed or removable reference points are availa-ble with both models.
SPECIFICATIONS
Range 25 mm
Resolution 0.001 mm
Operating temperature 0°C to +40°C
Accuracy ±0.003 mm or less
Reading instrument LCD gauge
EXTE
NSOM
ETER
EX
TENS
OMET
ER
EXTE
NSOM
ETER
EX
TENS
OMET
ER
SPECIFICATIONS
Caliper accuracy ±0.02 mm (digital) or ±0.04 mm (vernier)
Maximum relative displacement (convergence / diver-gence):
x axis: 50 mm / 40 mm y axis: 30 mm / ∞ z axis: 10 mm / ∞
Dimensions (W × L × D) 210 × 180 × 60 mm
INCLINOMETER 24
INCLINOMETER
HORIZONTAL IN-PLACE INCLINOMETER HORIZON-M
FLEXIBLE INCLINOMETER CHAIN RT-FXI
The HORIZON-M In-Place Inclinometer con-sists of inclinometer casing and a chain of incli-nometer sensors. The inclinometer casing, which controls the orientation of the sensors, is installed in a trench or horizontal borehole with one set of grooves oriented vertically. The sen-sors measure the inclination of the casing (tilt from horizontal). Changes in the inclination readings indicate that the casing has been dis-placed by ground movement.
SPECIFICATIONS
Angular range ±10°
Resolution 0.0025°
Repeatability ±0.006°
Sensor type MEMS (tilt) and thermistor (T°)
RT-FXI Flexible Inclinometer Chain can be placed in a borehole or embedded within a structure to monitor lateral deformation. The system consists of a series of interconnected nodes containing MEMS accelerometers. Standard segments are 3 meters long and include 5 nodes. Custom, permanent-assembly segment lengths are also available. The RT-FXI is easily assembled on site, which enables fast deployment for various depth configura-tions.
SPECIFICATIONS
Node length 600 mm or 2 ft
Segment length (Standard)
3 m or 10 ft 5 nodes per segment
Maximum length 100 m
Calibrated range ±0.30°
Casing 38 mm (1.5") ID Schedule 40 pipe 70 mm (2.75") inclinometer casing
INCLINOMETER SYSTEM PROFIL
The PROFIL Inclinometer System used to measure lateral displacement of soil, rock and structures such as dams, retaining walls and tunnels. The system features an Android tablet used to obtain the readings. The free Roctest PROFIL application features a convenient, hands free mode and allows sharing of results through email or Dropbox (Wi-Fi required). The PROFIL comes standard with a detachable probe making it easy to handle and transport.
SPECIFICATIONS
Calibration range ±30° (standard)
Resolution 0.005 mm (0.0002 in)
Repeatability ±0.003°
Operating temperature −20°C to +70°C
Cable lengths 30, 50, 75, 100, 150, 200, 250 or 300 m 100, 150, 200, or 300 feet
Probe Detachable (standard), or fixed
VERTICAL IN-PLACE INCLINOMETER PISA-M
The PISA-M In-Place Inclinometer (IPI) is used for continuous and unattended measure-ments of lateral displacement of soil, rock and structures such as dams, retaining walls and tunnels. The PISA-M uses a MEMS sensor that monitors either uniaxial or biaxial tilt with built-in signal conditioning. This IPI is installed in a serial configuration, requiring only one ca-ble for up to 50 sensors.
SPECIFICATIONS
Angular range ±10°
Resolution 0.0025°
Repeatability ±0.006°
Sensor type MEMS (tilt) and thermistor (T°)
Max # of sensors1 50 (40 m), 40 (92 m), 30 (165 m), 20 (258 m), 10 (375 m)
INCL
INOM
ETER
IN
CLIN
OMET
ER
INCL
INOM
ETER
IN
CLIN
OMET
ER
1 Representing nominal limits of serial sensors per length of jumper cable
INCLINOMETER 25
INCLINOMETER
TELESCOPING SECTION GEO-LOK
GEO-LOK TELESCOPING Sections are at-tached to the same standard couplings that attach standard casings. When installing tele-scopic sections, they sould be supported in their extended position to avoid any premature closing.
SPECIFICATIONS
OD 73 mm / 89 mm
Length fully extended 791 mm
Length fully compressed 639 mm
INCLINOMETER CASING GEO-LOK
The GEO-LOK Inclinometer Casing used to house probes to measure lateral movements and deformation of soil, rock and structures. It requires no glue, rivets or shear wires to con-nect additional sections of pipe. GEO-LOK is easily disassembled and reused in the event of installation problems. Telescopic sections are available. When accuracy is critical, spiral sur-veys may be performed on deep installations.
SPECIFICATIONS
Casing OD 70 mm / 85 mm
Casing ID 59 mm / 72 mm
Coupling OD 72 mm / 87 mm
Casing length 1.5 m / 3 m
Spiral groove control <1/3° / 3 m
ANCHORS & GROUT PLUGS GEO-LOK
GEO-LOK ANCHORS & GROUT VALVES are available for 70 mm and 85 mm casing. The grout valves will typically be used in tight bore-holes where space for grout tubing is limited. The spring loaded anchors can be used in deep boreholes for maintaining casing in place.
SPECIFICATIONS
Anchor grout valve with gasket
70 mm / 85 mm
Plug grout valve with gasket
70 mm / 85 mm
Hydraulic coupling socket B8HP36
Anchor grout valve with quick connect
70 mm / 85 mm
Plug grout valve with quick connect
70 mm / 85 mm
INCL
INOM
ETER
IN
CLIN
OMET
ER
INCL
INOM
ETER
INCLINOMETER CASING GTI-1A
GTI-1A1 Inclinometer Casing is used to house inclinometer probes to measure lateral movements and deformation of soil, rock and structures. Couplings are assembled with sol-vent cement and rivets. When accuracy is criti-cal, spiral surveys may be performed on deep installations. 1Available for the European market only
Casing OD 60 mm
Casing ID 48.5 mm
Coupling OD 68 mm
Casing length 3 m
Spiral groove control <1/3° / 3 m
SPECIFICATIONS
INCL
INOM
ETER
PENDULUM / TILTMETER 26
PENDULUM / TILTMETER
SIGHTING READING TABLE MODEL 76 / OPTICAL COORDINOSCOPE MVR
BEAM SENSOR & TILTMETER EL BEAM
The SIGHTING READING TABLE Model 76 is used to take manual readings. The positions of the cursors are read directly off the scale and the vernier cursor. The readings are converted to wire displacement values.
The OPTICAL COORDINOSCOPE MVR con-sists of a reference base permanently installed at the reading point. Measurements are taken from a portable coordinoscope by reading the current X & Y displacement on the vernier.
READING TABLE 76 SPECIFICATIONS
Range ±15 mm
Resolution 0.1 mm
Accuracy 0.5 mm
The EL BEAM Sensor & Tiltmeter consists of an electrolytic tilt sensor housed in a compact weatherproof enclosure. The sensor can be configured as a beam sensor or a tiltmeter. The sensor has no moving parts. It is easy to install, it can also be removed and reused.
SPECIFICATIONS
Sensor type Electrolytic
Range ± 40 arc minutes
Resolution 1 arc seconds
Repeatability ± 3 arc seconds
Operating temperature −20°C to +50°C
Dimensions 125 x 80 x 59 mm
PENDULUM DIRECT & INVERTED
REMOTE READING PENDULUM STATION RxTx
PEND
ULUM
PE
NDUL
UM
PEND
ULUM
TI
LTM
ETER
The RxTx REMOTE READING PENDULUM STATION is used to monitor the relative hori-zontal and vertical displacements between a direct or inverted pendulum wire and a struc-ture. It optically measures the relative position of a pendulum wire in x and y axis of displacement in dams, foundations and other structures.
SPECIFICATIONS
Data storage capacity 370 readings / non-volatile RAM
Range 50 × 50 × 25 mm
Accuracy ±0.05 mm
Operating temperature −10°C to +40°C
Reading Station Manual or remote stations are
The DIRECT and INVERTED PENDULUM are designed to accurately measure the relative internal horizontal displacement of points along a true vertical line. They may be set up for re-mote reading and automatic data acquisition using a telependulum. Applications include mon-itoring of movements within dams, dam founda-tions, nuclear power stations, viaducts and bridge piers.
PENDULUM COMPONENTS
Direct Pendulum Inverted Pendulum
Stainless steel or invar wire Stainless steel or invar wire
Upper hook and vee-shaped guide bracket
Anchoring weight
Wire tensioning weight and hook
PVC float and float tank assembly
MVR SPECIFICATIONS
Range 400 mm
Accuracy 0.02 mm
Focal Range ±50 mm
TILTMETER 27
TILTMETER
ELECTROLYTIC TILTMETER TUFF TILT 420
The precise and rugged TUFF TILT Uniaxial or Biaxial Tiltmeter is suitable for many different applications. It combines precision, long-term stability and rugged durability in a compact and reliable instrument. Its 4-20 mA output is great for long cable runs, and it includes a thermistor for correlating tilt changes with thermally in-duced structural movement.
SPECIFICATIONS
Range ±0.5°/±3°/±50°
Resolution 0.0001°, 0.0006°, 0.01°
Output 4-20 mA Two wire current loop (per axis)
Operating temperature −40°C to +85°C
Dimensions 120 x 80 x 60 mm
Sensor type Electrolytic
MEMS TILTMETER MEMS TILT
The MEMS TILTMETER is a compact, water-proof tiltmeter with a range of ±10° from vertical. It is used to monitor changes in the inclination of a structure. The tiltmeter is fixed to the structure via an angle bracket that can be welded to steel or bolted to an anchor set into concrete or rock. Because the tiltmeter has a relatively wide range, careful zeroing of the sensor is not re-quired.
SPECIFICATIONS
Sensor type MEMS and a 3K ohm thermistor
Range ± 10 degrees
Resolution 9 arc seconds (13 bits readout)
Repeatability ±22 arc seconds
Operating temperature −8°C to +40°C
Dimensions 32 x 190 mm
WIRELESS MEMS TILTMETER LOADSENSING LS-G6-INC15
The LOADSENSING LS-G6-INC15 Wireless Tiltmeter is a low power long range wireless datalogger and inclinometer in a single compact box. Housed in a IP67 rugged enclosure, it is ideal for structural load testing, monitoring of walls and foundation movement. It features a communication range of up to 15km and over 5 years of battery life. This Tiltmeter is only com-patible with LOADSENSING Wireless Systems.
SPECIFICATIONS
Sensor type MEMS
Range ± 15 degrees
Resolution 0.001°
Battery life 5 years (1 reading/hour)
Operating temperature −40°C to +80°C
Dimensions 150 x 120 x 61 mm
Axes 2 (Biaxial)
TILT
MET
ER
TILT
MET
ER
TILT
MET
ER
DIGITAL MEMS TILTMETER JDI-100, JDI-200
The JDI-100/200 Series Tiltmeter is a MEMS digitally temperature compensated inclinometer available in a single (100) and dual (200) axis configurations. It is designed in a robust and rugged enclosure. A daisy chain version is avail-able.
SPECIFICATIONS
Sensor type MEMS
Axes Single or dual
Range ±1°/±3°/±14.5°/±30°/±60°
Connectivity Daisy chain (RS-485)
Operating temperature −40°C to +85°C
Dimensions 58 x 50 x 44 mm
TILT
MET
ER
CELL 28
LOAD & PRESSURE CELL
ANCHOR LOAD CELL ANCLO
The ANCLO Load Cell is fitted with electrical strain gauges and is used to measure tensile loads in tieback anchors, rock bolts, or com-pressive loads in structures. It is designed to meet the adverse and severe environmental conditions associated with construction or min-ing activities. The cell is available in annular configuration for tensile load, or in a solid con-figuration to monitor a compressive load.
HYDRAULIC LOAD CELL HYDLO
TOTAL PRESSURE CELL TPC
VIBRATING WIRE LOAD CELL VH
The HYDLO Hydraulic Load Cell is designed for direct measurement of loads in tieback anchors, rock bolts or compressive loads in structures. It is made of two plates welded together around the periphery and filled with de-aired oil. This design is also applied to monitor rock bolts used in mines and slope stabilization.
The TPC Total Pressure Cell consists of a sealed pad filled with oil connected via solid tubing to a pressure transducer. It is used for measurement of total pressure in soils and em-bankments, for measurement of stress in con-crete, or for measurement of contact pressure on retaining walls, piles and tunnel linings.
The VH Vibrating Wire Load Cell is used to measure loads in tiebacks, foundation anchors, rock bolts and tunnel supports. It is designed to meet the demand of adverse and severe envi-ronmental conditions associated with construc-tion or mining activities. The cell is available either in an annular configuration to monitor a tensile load, or in a solid configuration to monitor a compressive load.
SPECIFICATIONS
Load range1 100 to 10,000 kN
Operating temperature −40°C to +80°C
Option Submersible model
Accuracy ±0.5% F.S.
1 Higher ranges available for solid cells
SPECIFICATIONS
Load range 250 to 5,000 kN
Accuracy ±1% F.S.
Operating temperature −20°C to +60°C
Options Remote reading and/or electrical sensor
SPECIFICATIONS
Pressure range 200 to 10,000 kPa
Resolution1
With MB-3TL 0.025% F.S.
Options Vibrating wire, 4-20 mA or fiber optic sensor
Accuracy ±0.1% F.S.
1 Higher ranges available
SPECIFICATIONS
Load range1 500 to 10,000 kN
Operating temperature −20°C to +80°C
Option Submersible model
Accuracy ±0.5% F.S.
1 Higher ranges available for hollow cells
CEL
L CE
LL
CELL
C
ELL
STRAIN 29
STRAIN
EMBEDDED STRAIN GAUGE EM Series
The EM series of concrete embedment vibrating wire strain gauges can be directly embedded in concrete structures such as dams, piles, founda-tions and bridges. Three models are available: the standard model (EM-5), a larger model for use in mass concrete (EM-10), and a miniature model for laboratory use (EM-2).
SPECIFICATIONS
Range 3,000 με
Accuracy ±0 .5 % F.S.
Resolution EM-5: 1 με (Min) EM-2 & EM-10: 0.4 με
Operating temperature -20°C to +80ºC
Gauge length 50 mm (EM-2) 168 mm (EM-5) 254 mm (EM-10)
SURFACE MOUNT STRAIN GAUGE SM-5 Series
The SM-5 is a surface mount vibrating wire strain gauge used for monitoring variations in strain, allowing stress evaluation when the ma-terial’s modulus of elasticity is known. The gauge is mounted on structures such as bridg-es, piles, tunnels and linings. Two models, dif-fering in their mechanical supports, are availa-ble: the SM-5A, which is held tight by set- screws, and the SM-5B by hexagonal nuts.
SPECIFICATIONS
Range 3,000 με
Accuracy ±0.5 % F.S.
Resolution 1 με (Min)
Operating temperature −20°C to +80°C
Active gauge length 149 mm (SM-5A) 129 mm (SM-5B)
MINIATURE STRAIN GAUGE SM-2 Series
The SM-2 series of miniature vibrating wire strain gauges are used to measure strain in steel structures where access is limited. The SM-2 is offered in two models: the SM-2W is de-signed to be spot-welded and the SM-2A is generally installed inside a small diameter bore-hole.
SPECIFICATIONS
Range 3,000 με
Accuracy ±0.5 % F.S.
Resolution 0.4 με (Min)
Operating temperature −20ºC to +80ºC
SM-2W total length 76 mm
VIBRATING WIRE STRAIN GAUGE C-110
SPECIFICATIONS
Range 2,900 με
Operating temperature −20ºC to +80ºC
Gauge length 110 mm
Resolution 0.35 με
Total length 144 mm
Tube diameter 6 mm
Flange diameter 20 mm
STRA
IN
STRA
IN
STRA
IN
STRA
IN
Accurate, robust and corrosion resistant, the C-110 strain gauge is built with independent electro-magnetic excitation and pick-up coils. The C-110 strain gauge consists of a thin-wall steel tube with two steel heads soldered to its extremities using solder with a low modulus of deformation. The distance between flanges of the heads determines the gauge length. A small rectangular housing at the gauge midsection encloses the electro-magnetic excitation and pick-up coils.
STRAIN / SETTLEMENT
SETTLEMENT / TEMPERATURE 30
SETTLEMENT CELL TCP
The TCP SETTLEMENT CELL SYSTEM is used for measurement and control of vertical movement caused by settlement in the soil. The standard TCP system comprises two spher-ical cells half-filled with an anti-freeze solution and connected to a reading panel. A hand pump is used to push the anti-freeze solution back to the reading panel. The difference in elevation between the two cells can then be read directly on the two sight tubes mounted on the reading panel.
SPECIFICATIONS
Range 1.8 m
Capacity 2.8 liter
Mounting hole diameter 22 mm
Sphere diameter 203 mm
Accuracy ±2 mm
STRA
IN
SETT
LEM
ENT
SETT
LEM
ENT
SETT
LEM
ENT
SOIL SETTLEMENT GAUGE SSG
The SSG SETTLEMENT GAUGE is a soil set-tlement gauge used to measure settlement or heave at a precise location in soils. The SSG consists of a vibrating wire or fiber optic pres-sure transducer housed in a corrosion resistant stainless steel body. Robust and stable, it can be installed in boreholes, standpipes, soil or concrete. The settlement gauge can also be attached to structures for monitoring settlement.
SPECIFICATIONS
Range 5 m to 75 m
Accuracy ±0.5% F.S. (±0.1% F.S. optional)
Resolution 0.025% F.S.
SETTLEMENT SYSTEM NIVOLIC SG
The NIVOLIC SG SETTLEMENT SYSTEM is designed to measure relative settlement in a multi-point system. It consists of a series of chambers linked by a liquid line. One of the chambers is used as a reference for the calcula-tion of relative movements of all other cham-bers. Typical applications include dam founda-tions, bridge deflection, building columns and floor slabs.
SPECIFICATIONS
Range 100, 150, 300, 450, 600 mm
Accuracy of sensor ±0.1% F.S.
Resolution 0.02% F.S.
INSTRUMENTED REBAR IRHP
The IRHP INSTRUMENTED REBAR is a rein-forcing bar containing a vibrating wire strain gauge. It is used for measuring strain and load in concrete structures such as dams, founda-tions, piles and tunnel linings. It can be used as sister bars, incorporated into a rebar reinforce-ment system, or grouted into a borehole for ground support.
SPECIFICATIONS
Range Up to 360 kN
Resolution 0.4 με
Operating temperature −20ºC to +80ºC
Accuracy ±0.25% F.S.
Nominal rebar length 1 m (standard)
Nominal diameter From 13 to 50 mm
TEMPERATURE/ / MISCELLANEOUS 31
TEMPERATURE/ MISCELLANEOUS
CABL
E
ELECTRICAL CABLE
ELECTRICAL INSTRUMENTATION CABLES are used with most of our electrical transducers in a wide variety of applications and environ-ments. Typical cables are made of twisted shield pairs of conductors and have a copper drain. Special cables, such as vented or rein-forced, are also available. Different amounts of conductors per cable and different types of external sheathings are offered to suit site con-ditions and specific instrumentation.
SPECIFICATIONS
OD 3.7 to 12.7 mm
External sheathing PVC, polyethylene or rubber
Temperature −20 to +80°C (PVC jacket)
INFLATABLE PACKER LP & MP
The LP & MP Inflatable Packers are used to block or isolate specific zones in a borehole. The gland is made of reinforced rubber and a variety of diameters are available. Typical ap-plications include permeability testing, pressure grouting in fractured or unconsolidated for-mations, water injection and methane gas con-trol for mines.
PACK
ER
SPECIFICATIONS
Standard lengths 500 or 1,000 mm
Maximum OD (deflated) 30 to 170 mm
Center tube ID 10 to 81 mm
Types available Single or double
TEMPERATURE SENSOR TH Series
The TH SENSOR is used to monitor tempera-ture in rock, concrete, soil or grout. Ideal for dams, bridges, buildings and tunnel linings mon-itoring, it provides a reliable method to monitor the influence of temperature on instruments. The rugged design allows direct embedment in fresh concrete or grouting in boreholes. Its sens-ing element can either consist of a 3kΩ chip thermistor, a platinum resistor or a thermocou-ple.
SPECIFICATIONS
Temperature range1 −60°C to +400°C
Accuracy1 ±0.5% F.S.
Thermal drift 0.385 Ω / °C (TH-PT100)
Resolution1 0.1°C
1 Depending on sensor type
THERMISTOR STRING TH-C
The TH-C THERMISTOR STRING is a multi-conductor cable with individual temperature sensors distributed along the cable. The chains can be submerged underwater as well as under-ground. The cable is flexible even at low tem-perature. The thermistor used in the string has good stability over time. The temperature value can be obtained from a portable handheld readout instrument or a complete datalogger system.
SPECIFICATIONS
Temperature range −20°C to + 80°C
Thermal drift at 25°C Less than 0.01°C after 100 months
Submersion Up to 200 m deep (IP68)
Resistance at 50 3 kΩ
Max number of sensor per string
20
TEM
PERA
TURE
TE
MPE
RATU
RE
READOUT / DATALOGGER 32
READOUT / DATALOGGER
VIBRATING WIRE READOUT MB-3TL
SPECIFICATIONS
Display LCD, 2 lines, 20 characters
Range 460 to 6,000 Hz
Battery life 60 hours
Weight 1.8 kg
Dimensions 23.5 X 19 X 10.8 cm
PORTABLE DATALOGGER PFC-12
The PFC-12 Portable Datalogger is designed to accurately read and record data of all vibrating wire sensors (VW) in sustained and damped modes. Sensors’ temperature can be read by measuring the resistance of the sensors’ listening coil.
SPECIFICATIONS Measuring range 300 to 3,000 Hz
Displayed resolution 0.01 Hz
Temperature resolution 0.5°C
Accuracy ± 0.1% F.S.
Dimensions 152 x 304 x 355 mm
COMPACT DATALOGGER RT-VLOG
The RT-VLOG is a highly accurate, robust, compact and cost-effective Vibrating Wire (VW) datalogger designed to monitor all pluck and read types of vibrating wire sensors available on the market. The RT-VLOG is ideal for use in small and medium size projects. It is available in 4 & 8 channel configurations. The RT-VLOG is easy to set-up and requires no programming. An internal 900MHz Hermes Radio is an available option.
SPECIFICATIONS
Number of channels 4 or 8
Measuring range 450 to 6,000 Hz
Accuracy ± 0.002% Vibrating Wire Sensors
Displayed resolution ± 0.001% Vibrating Wire Sensors
Temperature resolution 0.1°C
Memory 63,500 records in non volatile memory
The MB-3TL Portable Readout Unit is battery operated with logging capability designed to read vibrating wire gauges and thermistors. The unit is ready to be used in the field, even in harsh environments, thanks to its splash proof case, sealed front panel and connector.
READ
OUT
DATA
LOGG
ER
DATA
LOGG
ER
DATA
LOGG
ER
PNEUMATIC PRESSURE INDICATOR PR-20 & PR-20D
The PR-20 Portable Pneumatic Pressure Indicator is designed to read pneumatic sensors from most manufacturers. It is mount-ed in a strong, watertight case containing a nitrogen gas cylinder with a maximum pres-sure of 10 000 kPa. Easy to use with an auto-matic flow control valve, the PR-20D model comes with a high precision digital pressure gauge.
SPECIFICATIONS
Range 200 kPa to 10,000 kPa
Operating temperature −20°C to +60°C (PR-20)
Dimensions 45 cm × 30 cm × 18 cm
Accuracy ±0.25% F.S. (PR-20)
READOUT / DATALOGGER 33
READOUT / DATALOGGER
1 See specifications on technical datasheet
SIGNAL MULTIPLEXER RT-MUX 16/32
WIRELESS INTERFACE MODULE SL SERIES
The RT-MUX 16/32 Signal Multiplexer is a cost effective way to expand the amount of channels a single datalogger can handle. It can accommodate up to 32 sensors (with 2 conduc-tors each) or 16 sensors (with 4 conductors each). The RT-MUX 16/32 has an ultra low power consumption with a quiescent current of less than 20uA.
The SL Interface Module Series offers a varie-ty of configurable interface modules designed to read data from electrical and/or vibrating wire sensors in a borehole. Available in wire-less mode, they are powered with a long life battery pack. Their modularity, waterproof de-sign, and robust antenna make them ideal for applications in very humid environments.
SPECIFICATIONS
Number of channels 16 channels (4 wires) 32 channels (2 wires)
Operating temperature −40°C to +70°C
Dimension 57 x 126 x 273 mm
Surge protection No protection (Standard) Gas tube protection (Optional) Full Protection (Optional)
SPECIFICATIONS
Dimensions 171 x 381 mm
Temperature range −25 to +50°C (-55 to +80°C option)
Battery Life 1 year (1 reading/ day)
Water resistance IP 68 300k Pa
Vibrating Wire +/- 0.013% of F.S. Accuracy
Analog reading +/- 0.12% of F.S. Accuracy
Radio Module 910 to 918 MHz
DATA ACQUISITION SYSTEM SENSLOG
The SENSLOG DATA ACQUISITION SYSTEM is used for remote monitoring of electrical sen-sors including vibrating wire. It is designed to automatically read any existing sensors on the market. The SENSLOG is well suited to oper-ate in harsh environments that may undergo extreme climatic changes. The capacity of the SENSLOG can be easily expanded by using the RT-MUX 16/32 multiplexer.
SPECIFICATIONS
Number of channels 8 differential or up to 16 single-ended
Excitation output 3 switched excitations, active during measurement1
Voltage requirements 9.6 to 16 V DC
Dimensions 41 × 36 cm
MUL
TIPL
EXER
IN
TERF
ACE
MOD
ULE
DATA
ACQ
UISI
TION
SWITCHING BOX RT-VWSB
The RT-VWSB Switching Box is used to group multiple sensors in a single location providing a convenient means of taking read-ings. It is designed to read up to twenty 4-conductor sensors, such as the vibrating wire gauge with its thermistor. Lightning protection for each sensor can be added as required.
SPECIFICATIONS
Number of channels 10, 16 or 20
Overall dimensions 30.5 × 20 cm NEMA 4X
Rotary switch Sealed contacts
Contact resistance 50 MΩ max
Insulation resistance 1.000 MΩ min
Options Lightning protection Multiplexer SW
ITCH
ING
BOX
ANALYSER / WIRELESS SYSTEM / VIBRATION 34
ANALYSER / WIRELESS SYSTEM / VIBRATION
VW ANALYZER CAMPBELL SCIENTIFIC
SPECIFICATIONS
Channel count 1 channel (VW & Thermistor)
Units Raw data Engineering units
Battery life 20 hours
Weight 0.34 kg
Dimensions 200 x 100 x 58 mm
Display Full color screen Easy to use menus
WIRELESS STAR NETWORKING LOAD SENSING
LOADSENSING Monitoring and Data Acquisi-tion System combines state-of-the-art wireless monitoring devices and advanced software tools.
LOADSENSING Devices are battery-powered and equipped with long-range, low-power wide area network (LPWA) radio communications and are compatible with a wide range of geotech-nical sensors.
SPECIFICATIONS
Software Intuitive web interface
Gateway Can manage up to 500 nodes
Nodes Up to 5 ch. 30 sec to 24hours sampling rate
Range Several kilometers between the nodes. Up to 9 miles/15 km.
Batteries Life span of up to 8 years.
Wireless topology Star Networking
VIBRATION MONITOR MICROMATE INSTANTEL
The robust and reliable MICROMATE Vibration Monitor provides reliable regulatory compli-ance monitoring with an ISEE or DIN Triaxial Geophone and ISEE Linear Microphone or Sound Level Microphone. The MICROMATE provides a touch screen interface. Support of USB 2.0 allows use of memory sticks and ap-proved external devices. It could easily be inte-grated in our SENSLOG.
SPECIFICATIONS
Geophone range Up to 254 mm/s
Geophone accuracy ± 5% F.S. (ISEE/DIN)
Microphone1 ISEE Linear Microphone Soud Level Microphone
Recording mode Waveform, Waveform Manual Histogram, Instantel Histogram
Dimensions 101.6 x 135.1 x 44.5 mm
Channels Microphone and triaxial Geophone
The VIBRATING-WIRE ANALYSER (VWA) is field ready to quickly measure a vibrating wire sensor, save data, and communicate results with custom PDF reports and spreadsheet out-put. Measurements are geo-located with an integrated GPS, allowing the device to verify locations and direct you to your sensors. A Pro-ject file maintains site/sensor information for 40 unique sites with 22 sensors per site.
VW A
NALY
SER
WIR
ELES
S W
IREL
ESS
VIBR
ATIO
N
WIRELESS MESH NETWORKING SENSEMETRICS
SPECIFICATIONS
Topology Mesh Nerworking
Wireless topology Intuitive web interface
Gateway The gateway transfers data from the thread onto the sensemetrics cloud/enterprise server.
Thread The threads are used to power and connect any sensemetrics inte-grated device/sensor.
The SENSEMETRICS Wireless Mesh Net-working Platform is an effortless and secure sensor mesh networking system that reduces the cost of sensor management. Comprehen-sive apps and applets display network metrics provide real-time and historical statistics for distributed devices and sensors.
Login to the cloud app or your enterprise server to manage and monitor your network.
1 Microphone sold separatly
Soil & Rock Testing Equipment Roctest has regularly contributed to the innovation and education of in-situ and laboratory testing equipment for soil and rock. We gained a unique expertise with pressuremeters by developing, manufacturing, and marketing this type of equipment for over 40 years. Roctest has a complete product line, including six types of pressuremeter to cover all your needs. Rentals are also available.
IN-SITU / LAB TESTING EQUIPMENT
An Unbroken Tradition of Quality Roctest has always been committed to providing high quality service along with the highest level of compe-tence and support.
IN-SITU / LAB TESTING EQUIPMENT 35
IN-SITU / LAB TESTING EQUIPMENT
IN-SITU TESTING EQUIPMENT
IN-SITU TESTING EQUIPMENT 36
SPECIFICATIONS
Max. working pressure 10,000 kPa
Probe type Volumetric measurement, monocellular
Probe diameter 44 mm (A), 74 mm (N)
Dimensions (TEXAM) 52 × 31 × 46 cm
Moduli range 1 to 2,000 MPa approx.
Loading Hydraulic
The TEXAMe Pressuremeter is used for in-situ loading tests at various depths on a routine basis. It was developed to offer an easier oper-ating type of pressuremeter. Cyclic and creep testing can be performed with the TEXAMe. It is a reliable instrument for the evaluation of most ground engineering problems. The TEXAMe comes with an optional D/P Box to interface with an optional Android Tablet.
PRESSUREMETER TEXAMe
BOREHOLE DILATOMETER (ROCK PRESSUREMETER) PROBEXe
The PROBEXe Dilatometer (rock pressure-meter) has a radially expandable borehole probe used to determine, in-situ, the modulus of elasticity of soft and moderately hard rocks. Tests run with the PROBEXe can reach working pressures of 30,000 kPa. The probe is inflated hydraulically by means of a two-way ram, and deformation readings are obtained by monitor-ing the displacement of the twin pistons.
SPECIFICATIONS
Max. working pressure 30,000 kPa
Probe type Volumetric measurement, monocellular
Moduli range 30 to 30,000 MPa approx.
Loading Hydraulic
Probe diameter 74 mm
The D/P Box Portable Datalogger Unit is designed to provide a friendly user interface with the TEXAMe, PROBEXe and DMP-95e.. The unit is ready to use in the field, even in harsh environments. The D/P Box Bluetooth connec-tion to an Android Tablet allows the operator to configure, perform the test, monitor live results and store the data on the Tablet.
SPECIFICATIONS Function Configuration, operation and data
collection for the TEXAMe, PRO-BEXe and DMP-95e
User interface Android Tablet
Communication Bluetooth (Android Tablet)
Power supply Rechargeable battery pack
BOREHOLE DILATOMETER DMP-95e
The DMP-95e Borehole Dilatometer is used for measurement of in-situ stress-strain proper-ties of rock. It consists of a probe with an alumi-num alloy central body. A sediment collector placed on top of the probe is equipped with a threaded end. The probe is fitted with displace-ment sensors, allowing anisotropic measure-ments. The DMP-95e comes with an optional D/P Box to interface an optional Android Tab-let.
SPECIFICATIONS
Max. working pressure 20,000 kPa
Moduli range 100 to 50,000 MPa approx.
Loading Pneumatic
Probe weight 45 kg approx.
Probe diameter 95 mm
Probe type Diametric measurement, monocel-lular (displacement sensors fitted)
IN-S
ITU
IN-S
ITU
IN-S
ITU
IN-S
ITU
DILATOMETER/PRESSUREMETER BOX D/P BOX
Android Tablet sold separately
D/P Box and Android Tablet sold separately
D/P Box and Android Tablet sold separately
D/P Box and Android Tablet sold separately
PRESSUREMETER G-AM II
SELF-BORING PRESSUREMETER BOREMAC
SPECIFICATIONS
Maximum working pressure 4,000 kPa
Probe type Volumetric measurement monocellular
Probe diameter 73 mm
Moduli range 1 to 100 MPa approx.
Loading Hydraulic
PRESSUREMETER PENCEL
PRESSUREMETER TRI-MOD-S
IN-S
ITU
IN-S
ITU
IN-S
ITU
IN-S
ITU
IN-SITU TESTING EQUIPMENT 37
SPECIFICATIONS
Maximum working pressure
2,500 kPa
Probe type Volumetric measurement monocellular
Probe diameter 32 mm
Moduli range 1 to 50 MPa approx.
Loading Hydraulic
SPECIFICATIONS
Maximum working pressure
10,000 kPa
Probe type Volumetric measurement, tri cellular
Probe diameter 44 mm, 60 mm, 74 mm
Moduli range 1 to 5,000 MPa approx.
Loading Pneumatic
SPECIFICATIONS
Maximum working pressure
20,000 kPa
Probe diameter 74 mm (N size)
Loading Hydraulic
Probe type Diametric measurement, monocellular (strain gauge canti-levered arms fitted)
Moduli range 30 to 15,000 MPa approx.
The G-AM II Menard Pressuremeter is used for measurement of in-situ strength and stress strain properties of soils, soft rock and perma-frost. It is an efficient instrument for the evalua-tion of many ground engineering problems. It features built-in high pressure conversion facili-ties and direct readout of guard cell pressure.
The BOREMAC Self-Boring Pressuremeter is used for in-situ measurement of properties of fine soils. It comprises a disintegrator module (disintegrator bit and shoe), an expandable probe protected with metallic fins, and the probe to outer EW-rod adaptor. Outer rods are used to insert and extract the probe. Inner rods are used to rotate the cutting tools and to inject drilling fluid.
The PENCEL Pressuremeter is a highly port-able testing equipment, offering simplicity and economical operation. The probe is set directly in place either by dynamically driving it or by statically pushing it into the soil. The probe is loaded hydraulically without the need of any compressed gas. A hollow PENCEL probe can be used in conjunction with a cone.
The TRI-MOD-S Pressuremeter is used to measure the in-situ strength and stress-strain properties of stiff soils and soft rocks. It stands out from the other pressuremeters by allowing tests to 20 000 kPa. It measures diametric changes, allowing anisotropic measurements.
IN-SITU TESTING EQUIPMENT
SPECIFICATIONS
Measurement range 0-200 kPa
Extension rod1 length 0.5 m
Vane dim. / Weight 16 × 32 mm / 0.05 kg 20 × 40 mm / 0.05 kg 25.4 × 50.8 mm / 0.06 kg
SPECIFICATIONS
Pressure gauge range Up to 2,000 kPa
Cones surface areas 5 x 10 cm2
Pressure rods 15 mm (dia.) x 1,000 mm (long)
SPECIFICATIONS
Total length 1,537 mm
Drop height 457 mm
Diam. of graduated stem 25.4 mm
Mass / total weight 4.55 / 11.82 kg
IN-SITU TESTING EQUIPMENT 38
Torque recorder capacity 1,150 kg-cm
Torque recorder dimen-sion / weight
38 x 38 x 25 cm / 25 kg
Vane dim. / capacity 5 x 11 cm / 215 kPa 6.5 x 13 cm / 110 kPa 8 x 17.2 cm / 60 kPa
Boring rods 20.6 mm (dia.) x 1 m (length)
SPECIFICATIONS
IN-SITU TESTING EQUIPMENT
VANE BORER M1000
The M1000 Vane Borer is a precision field instrument which consists of a torque recording head, boring rods, specially designed vanes, and a slip coupling. The head measures and records vane resistance, rod friction and angu-lar rotation. The system is supported by a torque head casing adaptor.
FIELD INSPECTION VANE TESTER H-60
The H-60 Field Inspection Vane Tester is used to provide a rapid check of the stability of foundations, excavations and trenches in clay. It enables quick and easy determination of the undrained shear strength of clay. The instru-ment is strong enough to be used as a handle during penetration and retraction of the vane.
PENETROMETER HSA-5
The HSA-5 Handheld Static Penetrometer was designed to make soundings to limited depths by the “Dutch Cone Static Penetrometer” method with a single string of rods.
PENETROMETER PEM-1
The PEM-1 Penetrometer is designed to per-form in situ dynamic penetration tests. This equipment consists of a hard steel stem with a cone shaped end and is inserted into the ground under the action of a falling mass. The PEM-1 is a compact and rugged piece of fieldequipment.
IN-S
ITU
IN-S
ITU
IN-S
ITU
IN-S
ITU
1 Six extension rods included allow depth measurement up to 3 meters
POINT LOAD TESTER PIL-7
FALL CONE APPARATUS G-200
HOEK TRIAXIAL CELL HTC
• FISO Reading Units1 (Static & Dynamic) • SOFO Reading Units2 (Static & Dynamic) • SOFO Optical Switch • MuST Dynamic Reading Unit • DiTemp Reading Unit3 • DiTeSt Reading Unit4 • Laser Distance Meter 3DeMon5
Note: Contact SMARTEC for specifications and availability.
SMARTEC - EQUIPMENT RENTALS
LAB TESTING EQUIPMENT / RENTALS 39
The PIL-7 Point Load Tester is designed to determine the point load strength index. This index provides a method to establish rock strength classification. The PIL-7 is a rugged system armoured with a shield for protection from flying chips upon failure. It is portable and durable and comes with conical platens.
The G-200 Fall Cone Apparatus is used to provide a quick and accurate method for deter-mining the undrained shear strength and the sensitivity of both undisturbed and remolded clays. This system is portable, fast, accurate and easy to use. It is also used to determine the liquid limits (fineness number).
The Hoek Triaxial Cell is designed to deter-mine the triaxial strength of diamond drill cores of rock or concrete. Tests carried out on a series of samples under different confining pressures allow the user to determine the strength and elastic properties, the shear strength at different confining pressures, the angle of shearing resistance, the cohesion, the modulus of elasticity and Poisson’s ratio.
SPECIFICATIONS
Maximum specimen size 102 mm
Weight 25 kg
Maximum load 70 kN
Pressure gauge range 100,000 kPa
Pressure gauge ±0.2% F.S.
SPECIFICATIONS
Undrained shear strength range
0.06 to 250 kPa
Weight with basic accessories
6 kg
SPECIFICATIONS
Triaxial cell1 complete with quick connect and plug
AWG 30.1 mm (1.185 in.) BWG 42.0 mm (1.655 in.) NQ 47.6 mm (1.875 in.) NWG 54.7 mm (2.155 in.) HQ 63.5 mm (2.500 in.)
Special Hoek Cells Membrane diameter
144.7 mm (5.7 in) 152.4 mm (6.0 in)
1 Other sizes available on request
LABO
RATO
RY
LABO
RATO
RY
EQU
IPM
ENT
RENT
ALS
LABO
RATO
RY
V3.0_R1.1_180401
LAB TESTING EQUIPMENT / RENTALS
1 1 1 5
2
2 2 3 4
SOLUTION PROVIDER Geotechnics | Environment | Structural Integrity | Safety Control | Installa on| Maintenance
Fiber Op c and Tradi onal Geotechnical Instrumenta on, System Design, Installa on, Opera on & Maintenance.
Roctest Ltd. 680 Birch Street St-Lambert, QC J4P 2N3 CANADA
Phone: 1-450-465-1113 Fax: 1-450-465-1938 Email: [email protected] Web: www.roctest.com
Telemac SAS 10 Eiffel Avenue 77220 Gretz-Armainvilliers FRANCE
Phone: +33-1-64-06-40-80 Fax: +33-1-64-06-40-26 Email: [email protected] Web: www.telemac.fr
Geotechnical and Environmental Inves ga ons
Smartec SA Via Pobiette 11 CH-6928 Manno SWITZERLAND
Phone: +41-91-610-18-00 Fax: +41-91-610-18-01 Email: [email protected] Web: www.smartec.ch
EN.OM.FRA. SAS 6-8 Eiffel Avenue 77220 Gretz-Armainvilliers FRANCE Phone: +33-1-64-06-47-76 Fax: +33-1-64-06-47-59 Email: [email protected] Web: www.enomfra.fr
Swiss Monitoring at Your Service