gmc motorhomes international - home - gmcmigmcmi.com/wp-content/uploads/2013/02/in_tank_fuel... ·...
TRANSCRIPT
![Page 1: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/1.jpg)
GMC MOTORHOMES INTERNATIONAL
IN-TANK FUEL PUMPS EMERY STORA September 30, 2010
![Page 2: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/2.jpg)
A very big
Thank You for
The Inventor, Bill Bramlett
and also the assistance of Bob Musgrove
for their help with this project.
![Page 3: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/3.jpg)
Premise: Fuel pumps are good for pumpingbut poor in sucking. Pressure ahead of apump will hold down vapor lock. Suctionbehind a pump creates a low pressure areasubject to vapor lock.
When an external pump sucks air it is some-times difficult to get it primed from the othertank.
By putting pumps into the tanks you eliminatethe lower pressure in the intake hose, eliminatethe selector valve, cool the pumps, and haveinstant priming -- all of which helps eliminatevapor lock.
![Page 4: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/4.jpg)
Picture by Rick Williams
![Page 5: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/5.jpg)
We will not change the fuel fill system.
However check the rubber connectorsat the tank and replace them if necessary.
Available from Jim Kanomata and others.
![Page 6: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/6.jpg)
Picture by Rick Williams
Original
![Page 7: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/7.jpg)
We will replace the rubber lineswith steel lines.
We eliminate the fuel selector valve.The fuel pumps have check valves sotheir outlets can be connected togetherand to the fuel line going to the engine.I tested them to 70 psi and they heldfine.
A new steel line goes from the pumpconnector to a fuel filter and thento the engine.
![Page 8: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/8.jpg)
Picture by Rick Williams
Original
![Page 9: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/9.jpg)
We will replace the rubber hoseson the top of the tank with steellines connected with short hoses tothe steel tube at the frame rail.
The rubber stub hoses can easily bereached alongside the tanks toreplace if ever necessary withoutdropping the tanks.
![Page 10: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/10.jpg)
Picture by Rick Williams
Original
![Page 11: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/11.jpg)
The only change made here isto replace the rubber hoses on the top of the tanks with steel lineswhich connect to the existing hoseswhich are shortened and now connect at the sides of the tanks.
Again making it easy to replace the hoseswithout dropping the tanks.
![Page 12: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/12.jpg)
Longer tube is vent.
Original sending unit
![Page 13: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/13.jpg)
Original sending unit
![Page 14: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/14.jpg)
PARTS
![Page 15: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/15.jpg)
Airtex E3902 Fuel Pump
O’Reilly $68.99 each plus taxAmazon.com $40.24 delivered
![Page 16: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/16.jpg)
Airtex FS1 Fuel Strainer
This has a plastic “cage” in the bottom to prevent the bottom from collapsingagainst the bottom of the tank.
O’Reilly Auto Parts $10.99 each plus tax Amazon.com $7.02 each delivered
![Page 17: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/17.jpg)
Alternate Carter Parts
The Carter equivalent to the Airtexpump E3902 is P74037.
The Carter equivalent to the AirtexSR1 filter is STS-2.
![Page 18: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/18.jpg)
You will need a bracket for the bottomof the pump. You can easily make yourown or find one at a junkyard from a GMpickup truck but you would have to pullthe fuel tank.
Use 1/16” thick steel plate.
Bracket for Bottom of Pump
![Page 19: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/19.jpg)
![Page 20: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/20.jpg)
Different pumps have different size bottoms.Know what you have before you make it.Circle inside tabs is sized by diameter of rubber.
Tabs are just bent up to hold pump. Large tab Is bent upand bolted to new vent pipe to hold bottom of pump.
![Page 21: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/21.jpg)
Brass Fittings
Use six 3/8” for fuel and vent lines.Use two 5/16” for vapor lines.Use one 1/4” right angle inverted flare topipe thread fitting for Onan fuel pickup.
![Page 22: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/22.jpg)
You will cut large rubber connector (comes with pump) and usea 3/4” piece. The insulators are 1/4”+ OD nylon “flangebushings” and smaller ID nylon washers from Ace Hardware.Drill “F” hole (.257”) in washer for press fit.
![Page 23: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/23.jpg)
Misc. Bolts, Nuts, Washers to fit.
Hose clamps to fit pump hose andfuel/vent hoses.
3/8” inverted flare coupler for fuel line.
Wire terminals to fit over bolt andlarger ones to fit over flange bushing.
Hoses for tanks and lines if needed.
![Page 24: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/24.jpg)
IMPORTANT!
BE SURE to test your fuel senderbefore using the sending unit toaccommodate you new pump.It should read approx. 90 ohms atfull and 0 ohms at empty.Mine were both 110 ohms and 10 ohms.
![Page 25: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/25.jpg)
Cutting lines on original fuel pickup.
![Page 26: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/26.jpg)
Cutting swedged ends from top of sender.
![Page 27: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/27.jpg)
View of inside sender
![Page 28: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/28.jpg)
Thread Vent Opening for 3/8 steel line
Use 5/16” x 24 tap followed by bottoming tap.
![Page 29: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/29.jpg)
Cut fuel pickup tube about 3/8”below top connection.
![Page 30: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/30.jpg)
Leave Sender Strap Intact, File Edges
After cutting fuel tube.
![Page 31: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/31.jpg)
A piece of steel 5/16” line will be cutand threaded on one end to screwinto threads tapped into vent opening.
This will support the fuel sending unitand the bottom of the fuel pump.Cut it just long enough to reach the tabon the pump bottom bracket that youwill bolt to it. 5” plus threads will do.
Important: drill 1/8” hole all the waythrough the tube just under thethreads at top to vent fuel tank.
![Page 32: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/32.jpg)
Showing vent tube before bolting sender to it. Position sender atthe approximate height it originally was in tank.
o
![Page 33: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/33.jpg)
Top of Pump Hose Clamps
Cut top of pumpplastic to 3/8”before putting itInto rubber hose.
![Page 34: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/34.jpg)
Close up of clampsand electrical passthrough.
![Page 35: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/35.jpg)
Bolt sending unit to side of vent tube.Bolt pump bracket to bottom of tube.
![Page 36: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/36.jpg)
![Page 37: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/37.jpg)
Drill 1/4” hole for nylon bushing
![Page 38: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/38.jpg)
Press washer over bushing. It helps to use ashort piece of tubing over the bushing and pullit together with a washer and nut. Cut thebushing flush with the top of washer. Don’tforget to put ground lug for pump under theinside of the bushing before pressing.
![Page 39: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/39.jpg)
Use a metalwasher over Nylon washerand a lockwasher overthe connector.
![Page 40: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/40.jpg)
Assembly of electricalpass through connector.Ground goes againstmetal below flange of bushing.
![Page 41: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/41.jpg)
Put groundwire 1/4” terminalunder flangeof bushing.Put hot wireunder bolt head.
![Page 42: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/42.jpg)
Finished Assembly
![Page 43: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/43.jpg)
Insert pumps into tankand connect steel lines.
Don’t forget to installfilter socks onto pumps.
![Page 44: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/44.jpg)
Rear Tank First
![Page 45: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/45.jpg)
After installing test at low pressurewith a soap solution.
![Page 46: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/46.jpg)
Lines connected with 3/8” compressionfittings. Wire connected with terminal.
![Page 47: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/47.jpg)
Rear Tankfuel pickup
![Page 48: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/48.jpg)
Rear tank vapor line hookup5/16” compression fitting.
![Page 49: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/49.jpg)
Rear tank Onan fuel pickup.Use 1/4” inverted flare topipe thread right angle adapter.
![Page 50: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/50.jpg)
Rear TankFinished View 1
![Page 51: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/51.jpg)
Rear TankFinished View 2
![Page 52: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/52.jpg)
Front Tank Next
![Page 53: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/53.jpg)
Front Tank fuel pickup line
![Page 54: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/54.jpg)
Front Tank fuelpickup with tee.Vent line connectswith short hose tosteel vent line
![Page 55: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/55.jpg)
Cutting vapor line
![Page 56: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/56.jpg)
Vapor line ready for fitting.
![Page 57: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/57.jpg)
Vapor line bent tofront of tank. Cut fitting off end for hose
![Page 58: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/58.jpg)
Remount tanks into GMC.
Hook up vapor lines to hosesgoing to vapor/fuel separator.
Connect fuel lines from rear tankwith an extension to tee.Come out of front of tee with afuel line to filter and to engine.
Connect vent lines to stub hosesto steel vent line inside frame.
![Page 59: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/59.jpg)
Fuel Pump Control Relay
![Page 60: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/60.jpg)
87
87a
86 85
30
87 normally open, on when switch is closed
87a normally closed, on when switch is off
86 wire from fuel selector switch on dash used to go to fuel selector valve
goes to AUX tank pump (front tank)
goes to MAIN tank pump (rear tank)
85 goes to ground
30 hot wire from TBI system to fuel pump
RELAY WIRING
![Page 61: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/61.jpg)
![Page 62: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/62.jpg)
![Page 63: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/63.jpg)
![Page 64: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/64.jpg)
![Page 65: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/65.jpg)
Highmountains
or hotdesert, NO
vaporlock here!
![Page 66: GMC MOTORHOMES INTERNATIONAL - Home - GMCMIgmcmi.com/wp-content/uploads/2013/02/In_tank_Fuel... · times difficult to get it primed from the other tank. By putting pumps into the](https://reader036.vdocuments.net/reader036/viewer/2022063012/5fc853ee35286f3ec64bff64/html5/thumbnails/66.jpg)
That’sall,
folks!:-),-)