gps quick installation guide_080710
TRANSCRIPT
7282019 GPS Quick Installation Guide_080710
httpslidepdfcomreaderfullgps-quick-installation-guide080710 13
Accutime GPS Module Quick Installat ion Guide
- 1 -
This Quick Installation Guide is intended for experienced installers For more information refer to the relevant sections in theSystem Manual and the Base Transceiver Station Installation and Manual
Preliminaries
Check that you have the following items available (all items should be ordered separately)
bull GPS Adapter cable
bull GPS ODU (GPS-OGR Outdoor unit)
bull Cable (IDU-ODU) - available in two lengths 50m 100m
GPS ODU Package Content
bull GPS ODU+antenna
bull Pole mounting kit (including plastic pipe bracket 2 clamps 4 M8 nuts washers and spring washers 1 x 1032 screwwasher and spring washer)
bull Ant GPS Surge Protection - (including 3 x 1032 screws washers and spring washers)
bull This installation guide
IDU-ODU Cable Package Content
bull Shielded Cat5E Ethernet cable (crimped on one side only - 12-pin waterproof round female) This is a proprietary cableand must be ordered from the equipment supplier
bull
2 shielded RJ -45 connectorsbull 1 RJ -45 plastic cover
Addi tional Equipment and Tools required for Installation
bull A grounding cable with appropriate terminations for connecting the indoor units ground terminal to the rack or to a groundconnection
bull Installation tools
WARNING ONLY experienced installation professionals who are familiar with local building and safety codes andwherever applicable are licensed by the appropriate government regulatory authorities should install outdoorunits and antennas Failure to do so may void the product warranty and may expose the end user or ServiceProvider to legal and financial liabilities The manufacturer and its resellers or distributors are not liable forinjury damage or regulation violations associated with the installation of outdoor units or antennas
ODU Installation
Figure 1 Figure 2 Figure 31 Place the bracket on a flat surface
and thread the supplied pipethrough the bracket hole and intothe GPS antenna (see Figure 1)Hand-tighten until snug Do notover-tighten or use a tool
2 Make sure the connector (male) ison the open side of the bracket (seeFigure 2)
3 Use the supplied screws washersand spring washers (2 x 1032) toassemble the surge protectioncable onto the bracket (see Figure3) Apply torque 21[Nm] (192[lbsin])
GPS Antenna
Pipe
Surge
Protectioncable
Bracket
Connector
PN 215041 J uly 2008
7282019 GPS Quick Installation Guide_080710
httpslidepdfcomreaderfullgps-quick-installation-guide080710 23
Accutime GPS Module Quick Installat ion Guide
- 2 -
Figure 4 Figure 5 Figure 6 4 Use a 1032 screw washer and
spring washer to attach the surgeprotectorrsquos grounding cable to thebracket (see Figure 4) Apply torque21[Nm] (192 [lbsin])
Make sure that the femaleconnector faces the antenna
5 Connect the surge protector cable(female connector) to the GPSantenna connector (male) Use thegroove on the cable connector(indicated by an arrow) as a guide
It aligns with the tenon in theconnector on the GPS side Turnthe locking ring on the cableconnector clockwise to secure theconnection Do not over-tighten
6 Use the supplied clamps toassemble the GPS and bracket ona pole Use the M8 nuts washersand spring washers to lock theclamps to the bracket Apply torque
9 [Nm] (80 [lbsin])
Figure 7 Figure 8 Figure 9 7 Connect the IDU-ODU cable Use
the groove on the cable connector(indicated by an arrow) as a guideIt aligns with the tenon in theconnector on the surge protectorside Turn the locking ring on thecable connector clockwise tosecure the connection Do not over-tighten
8 The bracket must be grounded Usean appropriate grounding cable
You can use the same screw usedfor grounding the surge protector (instep 4 above)
9 Fix the cable onto the pole using acable strip
10 Route the cable to the locationselected for the indoor equipment
Note Follow the instructions detailed inthePreparing the Indoor-to-Outdoor GPS Cable (supplied with the Cat5E GPS cable) to crimp the otherside of the IDU-ODU cable
11 Connect the RJ -45 connector fromthe GPS cable to the RJ -45 jack of the adapter cable
12 Connect the other end of the datacable (15-pin micro D-Type plug) tothe GPSSYNC IN connectorlocated on the NPU panel Tightenthe two screws until the cable isheld firmly
PN 215041 J uly 2008
7282019 GPS Quick Installation Guide_080710
httpslidepdfcomreaderfullgps-quick-installation-guide080710 33
Accutime GPS Module Quick Installat ion Guide
- 3 -
Preparing the IDU-ODU Cable
Use a crimp tool for RJ -45 connectors to prepare the wires Insert them into the appropriate pins and use the tool to crimp theconnector Make sure to do the following
bull Remove as small a length as possible of the external jacket Verify that the external jacket is well inside the sealingcover when connected to the unit to ensure good sealing
bull Pull back the shield drain wire before inserting the cable into the RJ -45 connector to ensure a good connection withthe connectors shield after crimping
For detailed instructions refer to the Preparing the Indoor-to-Outdoor GPS Cable instructions supplied with the Cat 5E GPScable
The following diagram shows the required wire pair pin-to-pin connectionsincluding the color codes used in cables supplied by the manufacturer
Wire color Pin
Orangewhite 1
Orange 2
Brownwhite 3
Brown 4
Blue 5
Bluewhite 6
Green 7
Greenwhite 8
PN 215041 J uly 2008
7282019 GPS Quick Installation Guide_080710
httpslidepdfcomreaderfullgps-quick-installation-guide080710 23
Accutime GPS Module Quick Installat ion Guide
- 2 -
Figure 4 Figure 5 Figure 6 4 Use a 1032 screw washer and
spring washer to attach the surgeprotectorrsquos grounding cable to thebracket (see Figure 4) Apply torque21[Nm] (192 [lbsin])
Make sure that the femaleconnector faces the antenna
5 Connect the surge protector cable(female connector) to the GPSantenna connector (male) Use thegroove on the cable connector(indicated by an arrow) as a guide
It aligns with the tenon in theconnector on the GPS side Turnthe locking ring on the cableconnector clockwise to secure theconnection Do not over-tighten
6 Use the supplied clamps toassemble the GPS and bracket ona pole Use the M8 nuts washersand spring washers to lock theclamps to the bracket Apply torque
9 [Nm] (80 [lbsin])
Figure 7 Figure 8 Figure 9 7 Connect the IDU-ODU cable Use
the groove on the cable connector(indicated by an arrow) as a guideIt aligns with the tenon in theconnector on the surge protectorside Turn the locking ring on thecable connector clockwise tosecure the connection Do not over-tighten
8 The bracket must be grounded Usean appropriate grounding cable
You can use the same screw usedfor grounding the surge protector (instep 4 above)
9 Fix the cable onto the pole using acable strip
10 Route the cable to the locationselected for the indoor equipment
Note Follow the instructions detailed inthePreparing the Indoor-to-Outdoor GPS Cable (supplied with the Cat5E GPS cable) to crimp the otherside of the IDU-ODU cable
11 Connect the RJ -45 connector fromthe GPS cable to the RJ -45 jack of the adapter cable
12 Connect the other end of the datacable (15-pin micro D-Type plug) tothe GPSSYNC IN connectorlocated on the NPU panel Tightenthe two screws until the cable isheld firmly
PN 215041 J uly 2008
7282019 GPS Quick Installation Guide_080710
httpslidepdfcomreaderfullgps-quick-installation-guide080710 33
Accutime GPS Module Quick Installat ion Guide
- 3 -
Preparing the IDU-ODU Cable
Use a crimp tool for RJ -45 connectors to prepare the wires Insert them into the appropriate pins and use the tool to crimp theconnector Make sure to do the following
bull Remove as small a length as possible of the external jacket Verify that the external jacket is well inside the sealingcover when connected to the unit to ensure good sealing
bull Pull back the shield drain wire before inserting the cable into the RJ -45 connector to ensure a good connection withthe connectors shield after crimping
For detailed instructions refer to the Preparing the Indoor-to-Outdoor GPS Cable instructions supplied with the Cat 5E GPScable
The following diagram shows the required wire pair pin-to-pin connectionsincluding the color codes used in cables supplied by the manufacturer
Wire color Pin
Orangewhite 1
Orange 2
Brownwhite 3
Brown 4
Blue 5
Bluewhite 6
Green 7
Greenwhite 8
PN 215041 J uly 2008
7282019 GPS Quick Installation Guide_080710
httpslidepdfcomreaderfullgps-quick-installation-guide080710 33
Accutime GPS Module Quick Installat ion Guide
- 3 -
Preparing the IDU-ODU Cable
Use a crimp tool for RJ -45 connectors to prepare the wires Insert them into the appropriate pins and use the tool to crimp theconnector Make sure to do the following
bull Remove as small a length as possible of the external jacket Verify that the external jacket is well inside the sealingcover when connected to the unit to ensure good sealing
bull Pull back the shield drain wire before inserting the cable into the RJ -45 connector to ensure a good connection withthe connectors shield after crimping
For detailed instructions refer to the Preparing the Indoor-to-Outdoor GPS Cable instructions supplied with the Cat 5E GPScable
The following diagram shows the required wire pair pin-to-pin connectionsincluding the color codes used in cables supplied by the manufacturer
Wire color Pin
Orangewhite 1
Orange 2
Brownwhite 3
Brown 4
Blue 5
Bluewhite 6
Green 7
Greenwhite 8
PN 215041 J uly 2008